The ISR currently consumes the rx buffer data and re-enables transmission
from within interrupt context. This is bad because if the interrupt
occurs again before the ISR exits, the new interrupt will be erroneously
cleared by the still completing ISR.
Simplified the ISR by just setting the completion variable and exiting with
no action. Then just looped the transmit functionality in
xilinx_spi_txrx_bufs().
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The code uses
return foo;
goto err_type;
when instead the form should have been
ret = foo;
goto err_type;
Here this causes a useful iio_device_put to be skipped.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If we pass an invalid clock type then "ts" is never set. We need to
check for errors earlier, otherwise we end up passing uninitialized
stack data to userspace.
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the no longer used endpoint-array access completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In summary, the symptom is intermittent key events lost after resume
on some machines with synaptics touchpad (seems this is synaptics _only_),
and key events loss is due to serio port reconnect after psmouse sync lost.
Removing psmouse and inserting it back during the suspend/resume process
is able to work around the issue, so the difference between psmouse_connect()
and psmouse_reconnect() is the key to the root cause of this problem.
After comparing the two different paths, synaptics driver has its own
implementation of synaptics_reconnect(), and the missing psmouse_probe()
seems significant, the patch below added psmouse_probe() to the reconnect
process, and has been verified many times that the issue could not be reliably
reproduced.
There are two PS/2 commands in psmouse_probe():
1. PSMOUSE_CMD_GETID
2. PSMOUSE_CMD_RESET_DIS
Only the PSMOUSE_CMD_GETID seems to be significant. The
PSMOUSE_CMD_RESET_DIS is irrelevant to this issue after trying
several times. So we have only implemented this patch to issue
the PSMOUSE_CMD_GETID so far.
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Signed-off-by: James M Leddy <james.leddy@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In intel_sdvo_get_lvds_modes() the wrong i2c adapter record is used
for DDC. Thus the code will always have to rely on a LVDS panel
mode supplied by VBT.
In most cases this succeeds, so this didn't get detected for quite
a while.
This regression seems to have been introduced in
commit f899fc64cd
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jul 20 15:44:45 2010 -0700
drm/i915: use GMBUS to manage i2c links
Signed-off-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about which commit likely introduced this issue.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All r8a7740 platforms now use the pinctrl API to control the HDMI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the FSI pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the CEU pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the GETHER
pins, the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the BSC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the INTC pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All r8a7740 platforms now use the pinctrl API to control the SCIF pins,
the corresponding function GPIOS are unused. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7740 has two LCDC units and two sets of LCDC output signals. By
default LCDC0 is routed to the LCD0 signals, and LCDC1 to the LCD1
signals. However, LCDC1 can be routed to the LCD0 signals by setting bit
MSEL6 in MSEL3CR (the LCD0 signals are further pinmuxed the usual way).
This could be configured by duplicating the LCD0 pin groups for LCDC1.
However, this would unnecessarily complicate the LCD pin groups, as no
r8a7740 board supported in mainline use such a configuration. Hardcode
the MSEL3CR MSEL6 bit to 0 for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When adding the INTC pin groups the INTC function hasn't been added to
the functions list. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No sh7372 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PFC GPIO API implementation moved to using port numbers. Replace all
GPIO_PORTx enum usage with the corresponding port number. The GPIO_PORTx
enum values are identical to the port number on this platform.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
pfc-r8a7778 will have many devices pfc support in the future,
and current pfc-r8a7778 is using pin/mux definition macro for SCIF.
The device definition style using macro is readable code IMO,
but creating new macro for each devices is not good sense.
This patch adds common SH_PFC_xx() macro for each new feature devices
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add VIN DATA[0:7]/CLK/HSYNC/VSYNC pin groups to R8A7779 PFC driver.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[horms+renesas@verge.net.au: trivial rebase on top of
"sh-pfc: r8a7779: Don't group USB OVC and PENC pins"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the RCAR_GP_PIN macro to convert from the documentation pin number
space to the linear pinctrl space.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIFA1 as preparation to switch to pinctrl in board files.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Refactor the GPIO macro magic to use GPIO numbers directly instead of
the GPIO_GP_x_y enum entries. This will allow removing the GPIO enum
entries from the mach/r8a7790.h header.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
No r8a7770 platform use the function GPIOs API. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: fixed typo in changelog: r8a7779 -> r8a7770]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GPIOs are now handled by a separate driver, remove GPIO data from the
SoC information structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make GPIO support optional for platforms that don't support GPIOLIB.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We add all necessary entries to support the external IRQs from the INTC.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial PFC support for the r8a7790 SoC.
At this point only GPIO interface is supported, move to
newer interfaces planned as incremental changes.
Original authors is Koji Matsuoka-san, thanks for him
and his team for the heavy lifting. Adjusted by Magnus
to work together with updated code in drivers/pinctrl.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@rms.renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As hardware support for this feature is not universal for all SoCs a flag,
has_both_edge_trigger, has been added to the platform data of the driver to
allow this feature to be enabled.
The motivation for this is to allow use of the gpio-keys driver on the
lager board which is based on the r8a7790 SoC. The V2 of this patch has been
fully exercised using that driver on that board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car H1 or Gen2 GPIO interrupts are assigned per each GPIO domain,
but, Gen1 E1/M1 GPIO interrupts are shared for all GPIO domain.
gpio-rcar driver needs IRQF_SHARED flags for these.
This patch was tested on Bock-W board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The USB_OVCn pins are alternate options for USB over-current detection
when using a 3.3V USB interface. As they're not mandatory they can be
used independently of the USB PENC pins. Don't group the USB_OVCn and
PENC pins to avoid conflicts when the USB_OVCn pins are used by another
function.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A few small fixes for v3.10, documentation things in the core and a few
driver bugs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yE/I
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small fixes for v3.10, documentation things in the core and a
few driver bugs."
* tag 'regulator-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: palmas: Fix "enable_reg" to point to the correct reg for SMPS10
regulator: palmas: Fix incorrect condition
regulator: core: Correct spelling mistake in comment
regulator: dbx500: Make local symbol static
regulator: Fix kernel-doc generation warnings.
Smatch complains that if we pass an invalid clock type then "ts" is
never set. We need to check for errors earlier, otherwise we end up
passing uninitialized stack data to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cfcec52e97.
This regresses a longstanding behaviour on X86 systems, which end up with
PCI serial ports moving between ttyS4 and ttyS0 when you bisect to opposite
sides of this commit, resulting in the need to constantly modify the console
setting in order to bisect across it.
Please revert, we can work on solving this for ARM platforms in a less
disruptive way.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Karthik Manamcheri <karthik.manamcheri@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the uart controller clock is enabled prior to writing to the
interrupt mask and pending registers in the s3c24xx_serial_init_port
function.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only want to enable hardware flow control if RTS/CTS pins
are connected.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxs interrupt controller does not support polling for interrupts,
but the driver still does it, which is a relict from
pre-MULTI_IRQ_HANDLER times.
The existing code assumes that 0x7f means no interrupt, but this value
is an actually valid irq number, namely gpio bank 0's irq. This results
in the driver not detecting when irq 0x7f is active which makes the
machine effectively dead lock.
This patch removes the interrupt poll loop and allows usage of gpio0
interrupt without an infinite loop.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's not supported yet. Fixes display issues when
users force it on.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
Bug reports:
https://bugzilla.redhat.com/show_bug.cgi?id=845745https://bugs.launchpad.net/ubuntu/+source/linux/+bug/561789https://bbs.archlinux.org/viewtopic.php?id=156964
Signed-off-by: Adis Hamzić <adis@hamzadis.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When we build a kernel with support for both ARMv6 and ARMv7,
gas is trying to be helpful by pointing out that the arm-cci
driver would not work on ARMv6:
/tmp/ccu1LDeU.s: Assembler messages:
/tmp/ccu1LDeU.s:450: Error: selected processor does not support ARM mode `wfi '
/tmp/ccu1LDeU.s:451: Error: selected processor does not support ARM mode `wfe '
make[4]: *** [drivers/bus/arm-cci.o] Error 1
We know that the driver will only be used on ARMv7, hence we
can annotate the inline assembly listing to allow those instructions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Dave Martin <dave.martin@linaro.org>
Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.
The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: Ben Mesman <ben@bnc.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we always force the pipe A to on we can't use the hw state to
decide whether it should be on. Hence quirk the quirk.
The problem is that crtc->active tracks the state of the entire
display pipe, i.e. including planes, encoders and all. But our hw
state readout simply looks at the pipe. But with the pipe A quirk we
force-enable that (together with it's pll). To fix that mismatch we
have two options:
- Quirk the checked state to match what our sw tracking states if the
pipe A quirk is in effect.
- Improve the hw state readout to not get fooled by the pipe A quirk.
Since we already have similar state clamping in e.g. assert_pipe I've
opted for the first variant. Also note that we don't really loose any
state checking: Individual pieces of the abstract crtc pipe are
checked in the enable/disable functions with the various asssert_*
checks we have, and the hw state check code doesn't check anything if
the pipe is off anyway.
v2: Pimp commit message after discussion with Chris and only apply the
quirk for the quirk if we're checking pipe A. Otherwise we'll miss
state checking for pipe B on i830M ...
v3: Make the code comment consistent with the improved commit message,
too (Chris).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64764
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: mlsemon35@gmail.com (v1)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson noticed that since
commit 1f83fee08d [v3.9]
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Nov 15 17:17:22 2012 +0100
drm/i915: clear up wedged transitions
X can again get -EIO when it does not expect it. And even worse score
a SIGBUS when accessing gtt mmaps. The established ABI is that we
_only_ return an -EIO from execbuf - all other ioctls should just
work. And since the reset code moves all bos out of gpu domains and
clears out all the last_seqno/ring tracking there really shouldn't be
any reason for non-execbuf code to ever touch the hw and see an -EIO.
After some extensive discussions we've noticed that these spurios -EIO
are caused by i915_gem_wait_for_error:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg20540.html
That is easy to fix by returning 0 instead of -EIO, since grabbing the
dev->struct_mutex does not yet mean that we actually want to touch the
hw. And so there is no reason at all to fail with -EIO.
But that's not the entire since, since often (at least it's easily
googleable) dmesg indicates that the reset fails and we declare the
gpu wedged. Then, quite a bit later X wakes up with the "Timed out
waiting for the gpu reset to complete" DRM_ERROR message in
wait_for_errror and brings down the desktop with an -EIO/SIGBUS.
So clearly we're missing a wakeup somewhere, since the gpu reset just
doesn't take 10 seconds to complete. And indeed we're do handle the
terminally wedged state wrong.
Fix this all up.
References: https://bugs.freedesktop.org/show_bug.cgi?id=63921
References: https://bugs.freedesktop.org/show_bug.cgi?id=64073
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
smatch reports the following warnings:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi)
See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch reports the following warnings:
drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg)
See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan
Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This
patch adds support for it.
Cc: linux-stable <stable@vger.kernel.org> # >= v3.8
Signed-off-by: Jonas Peterson <jonas.peterson@gmail.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a bug fix for some versions of g200se cards while doing
mode-setting.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
ARM cannot handle udelay for more than 2 miliseconds, so we
should use mdelay instead for those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@gmail.com>
The dependecies for BACKLIGHT_CLASS_DEVICE are defined a bit
strange, but it seems one has to always select both BACKLIGHT_CLASS_DEVICE
and BACKLIGHT_LCD_SUPPORT to avoid this error:
drivers/gpu/drm/tilcdc/tilcdc_panel.c:396:
undefined reference to `of_find_backlight_by_node'
Cc: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@gmail.com>
When GPU acceleration is disabled, drm_vblank_cleanup() will free the
vblank-related data, such as vblank_refcount, vblank_inmodeset, etc.
But we found that drm_vblank_post_modeset() may be called after the
cleanup, which use vblank_refcount and vblank_inmodeset. And this will
cause a kernel panic.
Fix this by return immediately if dev->num_crtcs is zero. This is the
same thing that drm_vblank_pre_modeset() does.
Call trace of a drm_vblank_post_modeset() after drm_vblank_cleanup():
[ 62.628906] [<ffffffff804868d0>] drm_vblank_post_modeset+0x34/0xb4
[ 62.628906] [<ffffffff804c7008>] atombios_crtc_dpms+0xb4/0x174
[ 62.628906] [<ffffffff804c70e0>] atombios_crtc_commit+0x18/0x38
[ 62.628906] [<ffffffff8047f038>] drm_crtc_helper_set_mode+0x304/0x3cc
[ 62.628906] [<ffffffff8047f92c>] drm_crtc_helper_set_config+0x6d8/0x988
[ 62.628906] [<ffffffff8047dd40>] drm_fb_helper_set_par+0x94/0x104
[ 62.628906] [<ffffffff80439d14>] fbcon_init+0x424/0x57c
[ 62.628906] [<ffffffff8046a638>] visual_init+0xb8/0x118
[ 62.628906] [<ffffffff8046b9f8>] take_over_console+0x238/0x384
[ 62.628906] [<ffffffff80436df8>] fbcon_takeover+0x7c/0xdc
[ 62.628906] [<ffffffff8024fa20>] notifier_call_chain+0x44/0x94
[ 62.628906] [<ffffffff8024fcbc>] __blocking_notifier_call_chain+0x48/0x68
[ 62.628906] [<ffffffff8042d990>] register_framebuffer+0x228/0x260
[ 62.628906] [<ffffffff8047e010>] drm_fb_helper_single_fb_probe+0x260/0x314
[ 62.628906] [<ffffffff8047e2c4>] drm_fb_helper_initial_config+0x200/0x234
[ 62.628906] [<ffffffff804e5560>] radeon_fbdev_init+0xd4/0xf4
[ 62.628906] [<ffffffff804e0e08>] radeon_modeset_init+0x9bc/0xa18
[ 62.628906] [<ffffffff804bfc14>] radeon_driver_load_kms+0xdc/0x12c
[ 62.628906] [<ffffffff8048b548>] drm_get_pci_dev+0x148/0x238
[ 62.628906] [<ffffffff80423564>] local_pci_probe+0x5c/0xd0
[ 62.628906] [<ffffffff80241ac4>] work_for_cpu_fn+0x1c/0x30
[ 62.628906] [<ffffffff802427c8>] process_one_work+0x274/0x3bc
[ 62.628906] [<ffffffff80242934>] process_scheduled_works+0x24/0x44
[ 62.628906] [<ffffffff8024515c>] worker_thread+0x31c/0x3f4
[ 62.628906] [<ffffffff802497a8>] kthread+0x88/0x90
[ 62.628906] [<ffffffff80206794>] kernel_thread_helper+0x10/0x18
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Binbin Zhou <zhoubb@lemote.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Pull s390 fixes from Martin Schwidefsky:
"Recent bug fixes, one of them touches a common code file.
It adds two #ifndef/#endif pairs to asm-generic/io.h to be able to
override xlate_dev_kmem_ptr and xlate_dev_mem_ptr."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pgtable: Fix gmap notifier address
s390/dasd: fix handling of gone paths
s390/pgtable: Fix check for pgste/storage key handling
arch: s390: appldata: using strncpy() and strnlen() instead of sprintf()
s390/smp: lost IPIs on cpu hotplug
kernel: Fix s390 absolute memory access for /dev/mem
s390/dma: do not call debug_dma after free
Pull libata changes from Tejun Heo:
"Nothing too interesting. PCI ID additions, some sata_rcar fixes and a
fringe bug fix for DMADIR handling which shouldn't affect any device
remotely modern."
* 'for-3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_rcar: fix interrupt handling
ahci: add an observed PCI ID for Marvell 88se9172 SATA controller
sata_rcar: clear STOP bit in bmdma_start() method
libata: make ata_exec_internal_sg honor DMADIR
ata_piix: add PCI IDs for Intel BayTail
libata: update "Maintained by:" tags
The driver's interrupt handling code is too picky in deciding whether it should
handle an interrupt or not which causes completely unneeded spurious interrupts.
Thus make sata_rcar_{ata|serr}_interrupt() *void*; add ATA status register read
to sata_rcar_ata_interrupt() to clear an unexpected ATA interrupt -- it doesn't
get cleared by writing to the SATAINTSTAT register in the interrupt mode we use.
Also, in sata_rcar_ata_interrupt() we should check SATAINTSTAT register only for
enabled interrupts and we should clear only those interrupts that we have read
as active first time around, because else we have a race and risk clearing an
interrupt that can occur between read and write of the SATAINTSTAT register
and never registering it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This patch addresses kernel bug 56661. BIOS reports an incorrect
backlight value, causing the driver to switch off the backlight
completely during startup. This patch ignores the incorrect value from
BIOS.
References: https://bugzilla.kernel.org/show_bug.cgi?id=56661
Signed-off-by: Ash Willis <ashwillis@programmer.net>
Cc: All <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On HP m4 lapops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugs.launchpad.net/bugs/1184501
Cc: All <stable@vger.kernel.org>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull parisc fixes from Helge Deller:
"This patcheset includes fixes for:
- the PCI/LBA which brings back the stifb graphics framebuffer
console
- possible memory overflows in parisc kernel init code
- parport support on older GSC machines
- avoids that users by mistake enable PARPORT_PC_SUPERIO on parisc
- MAINTAINERS file list updates for parisc."
* 'for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
A node starting before the minimum register is no reason to reject it,
since its end could be in range. The check for the end already exists
two lines lower, so we can just remove the incorrect check.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the above kernel error from parport_announce_port() on 32bit GSC
machines (e.g. B160L). The parport driver requires now a pointer to the
device struct.
Signed-off-by: Helge Deller <deller@gmx.de>
If enabled, CONFIG_PARPORT_PC_SUPERIO scans on PC-like hardware for
various super-io chips by accessing i/o ports in a range which will
crash any parisc hardware at once.
In addition, parisc has it's own incompatible superio chip
(CONFIG_SUPERIO), so if we disable PARPORT_PC_SUPERIO completely for
parisc we can avoid that people by accident enable the parport_pc
superio option too.
Signed-off-by: Helge Deller <deller@gmx.de>
commit dc7dce280a
Author: Bjorn Helgaas <bhelgaas@google.com>
Date: Fri Oct 28 16:27:27 2011 -0600
parisc/PCI: lba: convert to pci_create_root_bus() for correct root bus
resources
Supply root bus resources to pci_create_root_bus() so they're correct
immediately. This fixes the problem of "early" and "header" quirks seeing
incorrect root bus resources.
added tests for elmmio_space.start while it should use
elmmio_space.flags. This for example led to incorrect resource
assignments and a non-working stifb framebuffer on most parisc machines.
LBA 10:1: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0x12000-0x13fff] (bus address [0x2000-0x3fff])
pci_bus 0000:01: root bus resource [mem 0xfffffffffa000000-0xfffffffffbffffff] (bus address [0xfa000000-0xfbffffff])
pci_bus 0000:01: root bus resource [mem 0xfffffffff4800000-0xfffffffff4ffffff] (bus address [0xf4800000-0xf4ffffff])
pci_bus 0000:01: root bus resource [??? 0x00000001 flags 0x0]
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The non-PAT resource probing code failed to set the type of the LBA bus_num
resource (30aa80da43 "parisc/PCI: register busn_res for root buses" did
the corresponding thing for the PAT case).
This causes incorrect resource assignments and a non-working stifb
framebuffer on most parisc machines.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Pull scsi target fixes from Nicholas Bellinger:
"The highlights include:
- Re-instate sess->wait_list in target_wait_for_sess_cmds() for
active I/O shutdown handling in fabrics using se_cmd->cmd_kref
- Make ib_srpt call target_sess_cmd_list_set_waiting() during session
shutdown
- Fix FILEIO off-by-one READ_CAPACITY bug for !S_ISBLK export
- Fix iscsi-target login error heap buffer overflow (Kees)
- Fix iscsi-target active I/O shutdown handling regression in
v3.10-rc1
A big thanks to Kees Cook for fixing a long standing login error
buffer overflow bug.
All patches are CC'ed to stable with the exception of the v3.10-rc1
specific regression + other minor target cleanup."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix iscsit_free_cmd() se_cmd->cmd_kref shutdown handling
target: Propigate up ->cmd_kref put return via transport_generic_free_cmd
iscsi-target: fix heap buffer overflow on error
target/file: Fix off-by-one READ_CAPACITY bug for !S_ISBLK export
ib_srpt: Call target_sess_cmd_list_set_waiting during shutdown_session
target: Re-instate sess_wait_list for target_wait_for_sess_cmds
target: Remove unused wait_for_tasks bit in target_wait_for_sess_cmds
discrete clock expander chip. Most fixes are corrections to lousy clock
data of one form or another.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OuqZ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock subsystem fixes from Mike Turquette:
"A mix of small fixes affecting mostly ARM platforms as well as a
discrete clock expander chip. Most fixes are corrections to lousy
clock data of one form or another."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: Include clk mxs header file
clk: vt8500: Fix unbalanced spinlock in vt8500_dclk_set_rate()
clk: si5351: Set initial clkout rate when defined in platform data.
clk: si5351: Fix clkout rate computation.
clk: samsung: Add CLK_IGNORE_UNUSED flag for the sysreg clocks
clk: ux500: clk-sysctrl: handle clocks with no parents
clk: ux500: Provide device enumeration number suffix for SMSC911x
Pull assorted fixes from Al Viro:
"There'll be more - I'm trying to dig out from under the pile of mail
(a couple of weeks of something flu-like ;-/) and there's several more
things waiting for review; this is just the obvious stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
zoran: racy refcount handling in vm_ops ->open()/->close()
befs_readdir(): do not increment ->f_pos if filldir tells us to stop
hpfs: deadlock and race in directory lseek()
qnx6: qnx6_readdir() has a braino in pos calculation
fix buffer leak after "scsi: saner replacements for ->proc_info()"
vfs: Fix invalid ida_remove() call
From Nicolas Pitre:
This is the first MCPM backend submission for VExpress running on RTSM
aka Fast Models implementing the big.LITTLE system architecture. This
enables SMP secondary boot as well as CPU hotplug on this platform.
A big prerequisite for this support is the CCI driver from Lorenzo
included in this pull request.
Also included is Rob Herring's set_auxcr/get_auxcr allowing nicer code.
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'VExpress_DCSCB' of git://git.linaro.org/people/nico/linux:
ARM: vexpress: Select multi-cluster SMP operation if required
ARM: vexpress/dcscb: handle platform coherency exit/setup and CCI
ARM: vexpress/dcscb: do not hardcode number of CPUs per cluster
ARM: vexpress/dcscb: add CPU use counts to the power up/down API implementation
ARM: vexpress: introduce DCSCB support
ARM: introduce common set_auxcr/get_auxcr functions
drivers/bus: arm-cci: function to enable CCI ports from early boot code
drivers: bus: add ARM CCI support
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
Note: this branch only depends on mvebu/pcie in order to prevent managing a
tricky modify/remove file merge conflict. By rebasing on mvebu/pcie, we are
able to build the resolution into the patch series. The change is small, and
has been tested by the respective authors.
depends:
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRplb0AAoJEAi3KVZQDZAefTAH/1PMcXV+N/9HUgmx9XNpWg7Z
3ODWrA7Ewdvq9hfv9t+EH0FIdrZRA400p+AJuWSUuLzS7NzmCMTk/Pzad/W36ZY2
+8yJXVThSHqEQN/Vi1FtZGTKqRXZX/udVH5oNFV9jrUEFvLwuI/6/hCdkzlFKEol
9YJHNUyiul9P0jpcDXSSTFCpNXUPgQPuGTtIip0TKFmZOdA2QglgQAVkIwACZ+uX
PA7ewiFj1yfOhv8eh+nnb5kAsJEj1ynfMJywn7P/OC6ugAJtE9D0ZpzlYuj3lFEo
Z2snnzU7wVARfp1i6x3kNUyBiGHnJfxJC1KMePj87XP80BVzX1rmCoFY6x9nutg=
=jIi7
-----END PGP SIGNATURE-----
Merge tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu clock restructuring for v3.11
- clk: mvebu
- reorganize by SoC to remove built up #ifdefs
- add clk flags per clock gate
* tag 'seb_clk-3.11' of git://git.infradead.org/users/jcooper/linux:
clk: mvebu: disintegrate obsolete file
ARM: mvebu: move DT boards to SoC-centric clock init
ARM: kirkwood: move DT boards to SoC-centric clock init
ARM: dove: move DT boards to SoC-centric clock init
clk: mvebu: add Armada XP SoC-centric clock init
clk: mvebu: add Armada 370 SoC-centric clock init
clk: mvebu: add Kirkwood SoC-centric clock init
clk: mvebu: add Dove SoC-centric clock init
clk: mvebu: add common clock functions for core clk and clk gating
clk: mvebu: introduce per-clock-gate flags
- mvebu
- allow enumeration of devices beyond physical bridges
- remove faking the slot location
- fix status register emulation
depends
- mvebu/pcie
-mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpP2uAAoJEAi3KVZQDZAean8IAKvwIK5TzLB289GKL26NLgMs
c7FxMseuTLzlc036BU85UhDJ62bjVcUCukWzGhF1YxGGr+46gdJ2/aRZ8cvAz3pu
VDZCFo8V7A9VjoTZZ/MX3bzmdJbtgJD9G9PI69LX1sf+4WqlybVBhR9wFlyh9Zws
iolfLGDpCqDwkI5YH1R3XI6KCcP5P+QC52gXb4Due0lRMULTfDiWUqfJs7nqSAnH
AyM4SjImgXwWNVdKvK73uxbUmfG2pguvN20tq+ox5UHfSIfHOd9Uuj2EIEAC2SE7
eWbr7YV+Ba6fD/2Mfhuia7bCD8LrwrTPz8c7A4Xvjp7tMUW20K53PRAn+W4W6Wo=
=TTX4
-----END PGP SIGNATURE-----
Merge tag 'pcie_bridge-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (bridge) for v3.11
- mvebu
- allow enumeration of devices beyond physical bridges
- remove faking the slot location
- fix status register emulation
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_bridge-3.11' of git://git.infradead.org/users/jcooper/linux:
pci: mvebu: fix the emulation of the status register
pci: mvebu: allow the enumeration of devices beyond physical bridges
pci: mvebu: no longer fake the slot location of downstream devices
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpP1WAAoJEAi3KVZQDZAeItIH/1QVHhqYSpOnXGu4zQHswvIM
SRQoy4hiCJm+yywTnIDJPMQdBKD1vURRRdGWQouNsFoBaHki4v2BBxfBNFoDN+rx
VtECH7F1SbJ/Pb7XLVnswqRXVNqrY5fOY5mW42ALFBT9VxcKoD1FyqCaXfaU9JA4
VQCzR7DjFhr8bppZknQ5ZT/qI66Wj1oNiJtBdItmxT0pVfElvAOV6FHzfMGrrDrM
+v8T8KdFIdmH1Ny5J5KLQSE9qBLqae0vlDNgsfwfh1DY/Lye3rDHqPDKrh7YZjHR
xNc6JU+zEdP3tK1f1jgmjn/giY7HqpAFm46p9k/pF9gsE5SE0L/e0Dh9apOcq24=
=qUyf
-----END PGP SIGNATURE-----
Merge tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: convert db-88f6281/db-88f6282 to the Device Tree
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
arm: kirkwood: move PCIe window init to legacy driver
pci: mvebu: enable driver usage on Kirkwood
- mvebu pcie
- fix return value check in mvebu_pcie_probe()
depends
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPzyAAoJEAi3KVZQDZAeuf0H/2FsmnLgvJh24z1B1HLuWm52
TYgoORahPsuoP7L2RZBU6n3++UuX4NGbVcagqRDe1Asou0oG0fu6oXbdn0d4avff
hoIuRq3LWhQ6DYaeV34vV8vM8x79HYM7FT92zX7VZKJ6TL6KGSHHSvVKhqWo7y65
++Ogtl5hzjyMzcQo5LoDQ+bqVLZpbfF7D/dreCCzzmlODqCNZGoBeZOwTqyR9kDW
aO65yDcsFIky2YAGz+uT0ItNpAtGzshJU/d6QTHNlvKeae2NjMqv2X7hP4161uQ4
NGyCsm7Aif5WnBQGQsvgCIPnuxTaYaGOSZQLMG7pN7TJQgx0sgF93HmX/gUI/WQ=
=ye72
-----END PGP SIGNATURE-----
Merge tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/soc
PCI-e driver for mvebu.
* tag 'pcie-3.11-2' of git://git.infradead.org/users/jcooper/linux:
pci: mvebu: fix return value check in mvebu_pcie_probe()
arm: mvebu: PCIe support is now available on mvebu
pci: PCIe driver for Marvell Armada 370/XP systems
clk: mvebu: add more PCIe clocks for Armada XP
clk: mvebu: create parent-child relation for PCIe clocks on Armada 370
of/pci: Add of_pci_parse_bus_range() function
of/pci: Add of_pci_get_devfn() function
of/pci: Provide support for parsing PCI DT ranges property
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the recent addition of 8021AD, we need to set the new field vlan_proto in
sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx().
This patch fixes the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the port list dump does not fit into one skb currently the
dump would start over again. Fix this by continue from the last dumped
port.
Introduced by commit d90f889e9c (team: handle sending port list in the
same way option list is sent)
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
worse, we lock ->resource_lock too late when we are destroying the
final clonal VMA; the check for lack of other mappings of the same
opened file can race with mmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When removing atmel_lcdfb module, the backlight is unregistered but not
blanked. (only for CONFIG_BACKLIGHT_ATMEL_LCDC case).
This can result in the screen going full white depending on how the PWM
is wired.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
When a too small framebuffer is given, the atmel_lcdfb_check_var
silently fails.
Adding an error message will save some head scratching.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
That patch failed to set proc_scsi_fops' .release method.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some devices only have support for MSI, not MSI-X. While MSI is more
limited, it still provides better performance than line-based interrupts.
Signed-off-by: Ramachandra Gajula <rama@fastorsystems.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
When a path is gone and dasd_generic_path_event is called with a
PE_PATH_GONE event, we must assume that any I/O request on that
subchannel is still running. This is unlike the dasd_generic_notify
handler and the CIO_NO_PATH event, which implies that the subchannel
has been cleared.
If dasd_generic_path_event finds that the path has been the last
usable path, it must not call dasd_generic_last_path_gone (which would
reset the state of running requests), but just set the
DASD_STOPPED_DC_WAIT bit.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.10 stream...
Regarding the NFC bits, Samuel says:
"This is the first batch of NFC fixes for 3.10, and it contains:
- 3 fixes for the NFC MEI support:
* We now depend on the correct Kconfig symbol.
* We register an MEI event callback whenever we enable an NFC device,
otherwise we fail to read anything after an enable/disable cycle.
* We only disable an MEI device from its disable mey_phy_ops,
preventing useless consecutive disable calls.
- An NFC Makefile cleanup, as I forgot to remove a commented out line when
moving the LLCP code to the NFC top level directory."
As for the mac80211 bits, Johannes says:
"This time I have a fix from Stanislaw for a stupid mistake I made in the
auth/assoc timeout changes, a fix from Felix for 64-bit traffic counters
and one from Helmut for address mask handling in mac80211. I also have a
few fixes myself for four different crashes reported by a few people."
And Johannes says this about the iwlwifi bit:
"This fixes a brown paper-bag bug that we really should've caught in
review. More details in the changelog for the fix."
On top of that...
Arend van Spriel and Hante Meuleman cooperate to send a series of AP
and P2P mode fixes for brcmfmac.
Gabor Juhos corrects a register offset for AR9550, avoiding a bus
error.
Dan Carpenter provides a fixup to some dmesg output in the atmel
driver.
And, finally...
Felix Fietkau not only gives us a trio of small AR934x fixes, but
also refactors the ath9k aggregation session start/stop handling
(using the generic mac80211 support) in order to avoid a deadlock.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for probing the COH 901 327 watchdog from
the device tree and also adds associated bindings.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds device tree support for the ST DDC I2C driver known
as "stu300" in the kernel tree.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes it possible to probe the COH901 pinctrl driver from
the device tree, and assigned the device tree node in the
gpio_chip so we can look up cross-references from the device
tree. Start grabbing the per-port (bank) IRQs by index instead
of by name so we don't have to look up the IRQs by name going
forward.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a simple device tree compat string for the U300 pin
controller. The base address is already passed properly as
a resource and everything works fine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Go ahead and propigate up the ->cmd_kref put return value from
target_put_sess_cmd() -> transport_release_cmd() -> transport_put_cmd()
-> transport_generic_free_cmd().
This is useful for certain fabrics when determining the active I/O
shutdown case with SCF_ACK_KREF where a final target_put_sess_cmd()
is still required by the caller.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull drm fixes from Dave Airlie:
"One qxl 32-bit warning fix, the rest is a bunch of radeon fixes from
Alex for some issues we've been seeing."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/qxl: fix build warnings on 32-bit
radeon: use max_bus_speed to activate gen2 speeds
drm/radeon: narrow scope of Apple re-POST hack
drm/radeon: don't check crtcs in card_posted() on cards without DCE
drm/radeon: fix card_posted check for newer asics
drm/radeon: fix typo in cu_per_sh on verde
drm/radeon: UVD block on SUMO2 is the same as on SUMO
Fix the following sparse warnings:
drivers/clk/mxs/clk-imx28.c:72:5: warning: symbol 'mxs_saif_clkmux_select' was not declared. Should it be static?
drivers/clk/mxs/clk-imx28.c:156:12: warning: symbol 'mx28_clocks_init' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed $SUBJECT line]
If a key was larger than 64 bytes, as checked by iscsi_check_key(), the
error response packet, generated by iscsi_add_notunderstood_response(),
would still attempt to copy the entire key into the packet, overflowing
the structure on the heap.
Remote preauthentication kernel memory corruption was possible if a
target was configured and listening on the network.
CVE-2013-2850
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where FILEIO was incorrectly reporting the number
of logical blocks (+ 1) when using non struct block_device export mode.
It changes fd_get_blocks() to follow all other backend ->get_blocks() cases,
and reduces the calculated dev_size by one dev->dev_attrib.block_size
number of bytes, and also fixes initial fd_block_size assignment at
fd_configure_device() time introduced in commit 0fd97ccf4.
Reported-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reported-by: Badari Pulavarty <pbadari@us.ibm.com>
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull x86 fixes from Peter Anvin:
- Three EFI-related fixes
- Two early memory initialization fixes
- build fix for older binutils
- fix for an eager FPU performance regression -- currently we don't
allow the use of the FPU at interrupt time *at all* in eager mode,
which is clearly wrong.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Allow FPU to be used at interrupt time even with eagerfpu
x86, crc32-pclmul: Fix build with older binutils
x86-64, init: Fix a possible wraparound bug in switchover in head_64.S
x86, range: fix missing merge during add range
x86, efi: initial the local variable of DataSize to zero
efivar: fix oops in efivar_update_sysfs_entries() caused by memory reuse
efivarfs: Never return ENOENT from firmware again
During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.
Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use proper error paths
- Clean up APIC IPI usage (incorrect arguments)
- Delay XenBus frontend resume is backend (xenstored) is not running
- Fix build error with various combinations of CONFIG_
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRp59pAAoJEFjIrFwIi8fJRIYIAKvRh2Dp/AB44ZN97MW/QhEN
NUvrSTYr2HlqcUW7bv0ScrMLb0LlFeo+9s/bo0KI2+2F+zK822WPC+2KEZmzQIVs
q261dNsA3/HoyBDOLwWjatjsSus+njBOEgDIwARPwhkoon4fRXBnRJVMy+0bZC3I
fpd1nlUy0J7jW0QLO5ueKqd5ZN0Mkwn2H4+D8TOPVYHCnk3mT2W+qLCEJmkMxOuZ
iFYy95K1ky5r0leUUwCTUIGLmgftoh0Qo/RweXSmzuLiZrY+5ilike3gxQSiAjsM
lIjq+gKXNJJGz4M6wbOTfDzb/WQnKD+2PqlsbulrTD7E6RD6wIsqG/zvc1RqHqw=
=9gi8
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.10-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Use proper error paths
- Clean up APIC IPI usage (incorrect arguments)
- Delay XenBus frontend resume is backend (xenstored) is not running
- Fix build error with various combinations of CONFIG_
* tag 'stable/for-linus-3.10-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_client.c: correct exit path for xenbus_map_ring_valloc_hvm
xen-pciback: more uses of cached MSI-X capability offset
xen: Clean up apic ipi interface
xenbus: save xenstore local status for later use
xenbus: delay xenbus frontend resume if xenstored is not running
xmem/tmem: fix 'undefined variable' build error.
The following warning was seen on 3.9 when a corrected PCIe error was being
handled by the AER subsystem.
WARNING: at .../drivers/pci/search.c:214 pci_get_dev_by_id+0x8a/0x90()
This occurred because a call to pci_get_domain_bus_and_slot() was added to
cper_print_pcie() to setup for the call to cper_print_aer(). The warning
showed up because cper_print_pcie() is called in an interrupt context and
pci_get* functions are not supposed to be called in that context.
The solution is to move the cper_print_aer() call out of the interrupt
context and into aer_recover_work_func() to avoid any warnings when calling
pci_get* functions.
Signed-off-by: Lance Ortiz <lance.ortiz@hp.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch adds some code that inadvertently got left out of commit
c1fdb68e3d (USB: EHCI: changes related
to qh_refresh()). The calls to qh_refresh() and qh_link_periodic()
were taken out of qh_schedule(); therefore it is necessary to call
these routines manually after calling qh_schedule().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix below compile error:
drivers/built-in.o: In function `zcache_pampd_free':
>> zcache-main.c:(.text+0xb1c8a): undefined reference to `ramster_pampd_free'
>> zcache-main.c:(.text+0xb1cbc): undefined reference to `ramster_count_foreign_pages'
drivers/built-in.o: In function `zcache_pampd_get_data_and_free':
>> zcache-main.c:(.text+0xb1f05): undefined reference to `ramster_count_foreign_pages'
drivers/built-in.o: In function `zcache_cpu_notifier':
>> zcache-main.c:(.text+0xb228d): undefined reference to `ramster_cpu_up'
>> zcache-main.c:(.text+0xb2339): undefined reference to `ramster_cpu_down'
drivers/built-in.o: In function `zcache_pampd_create':
>> (.text+0xb26ce): undefined reference to `ramster_count_foreign_pages'
drivers/built-in.o: In function `zcache_pampd_create':
>> (.text+0xb27ef): undefined reference to `ramster_count_foreign_pages'
drivers/built-in.o: In function `zcache_put_page':
>> (.text+0xb299f): undefined reference to `ramster_do_preload_flnode'
drivers/built-in.o: In function `zcache_flush_page':
>> (.text+0xb2ea3): undefined reference to `ramster_do_preload_flnode'
drivers/built-in.o: In function `zcache_flush_object':
>> (.text+0xb307c): undefined reference to `ramster_do_preload_flnode'
drivers/built-in.o: In function `zcache_init':
>> zcache-main.c:(.text+0xb3629): undefined reference to `ramster_register_pamops'
>> zcache-main.c:(.text+0xb3868): undefined reference to `ramster_init'
>> drivers/built-in.o:(.rodata+0x15058): undefined reference to `ramster_foreign_eph_pages'
>> drivers/built-in.o:(.rodata+0x15078): undefined reference to `ramster_foreign_pers_pages'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Passing the value DMA_BIT_MASK(31) to dma_set_mask() causes the
dwc2-pci driver to sometimes fail (cannot enumerate the connected
device). Change it to DMA_BIT_MASK(32) instead, which is a more
sensible value anyway.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator_enable_regmap() uses enable_reg to enable the regulator.
But enable_reg for smps10 points to SMPS10_STATUS which is a
read-only register. Fixed the same by having enable_reg
set to SMPS10_CTRL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Since 'id' cannot take two values at the same time, the condition
should probably be an OR (||) instead of AND (&&).
Introduced by commit 28d1e8cd67 ("regulator: palma: add ramp delay
support through regulator constraints").
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch that converted raid5 to use bio_reset() forgot to initialize
bi_vcnt.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: NeilBrown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Tested-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Given that srpt_release_channel_work() calls target_wait_for_sess_cmds()
to allow outstanding se_cmd_t->cmd_kref a change to complete, the call
to perform target_sess_cmd_list_set_waiting() needs to happen in
srpt_shutdown_session()
Also, this patch adds an explicit call to srpt_shutdown_session() within
srpt_drain_channel() so that target_sess_cmd_list_set_waiting() will be
called in the cases where TFO->shutdown_session() is not triggered
directly by TCM.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Switch back to pre commit 1c7b13fe65 list splicing logic for active I/O
shutdown with tcm_qla2xxx + ib_srpt fabrics.
The original commit was done under the incorrect assumption that it's safe to
walk se_sess->sess_cmd_list unprotected in target_wait_for_sess_cmds() after
sess->sess_tearing_down = 1 has been set by target_sess_cmd_list_set_waiting()
during session shutdown.
So instead of adding sess->sess_cmd_lock protection around sess->sess_cmd_list
during target_wait_for_sess_cmds(), switch back to sess->sess_wait_list to
allow wait_for_completion() + TFO->release_cmd() to occur without having to
walk ->sess_cmd_list after the list_splice.
Also add a check to exit if target_sess_cmd_list_set_waiting() has already
been called, and add a WARN_ON to check for any fabric bug where new se_cmds
are added to sess->sess_cmd_list after sess->sess_tearing_down = 1 has already
been set.
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Six patches fixing up the suspend/resume and wakeup
handling of the Samsung and Exynos drivers.
- Errorpath fixes for four different drivers. All on
the probe() errorpath.
- Make the debugfs code for pin config take the right
mutex.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=J5kT
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin-control fixes from Linus Walleij:
- Six patches fixing up the suspend/resume and wakeup handling of the
Samsung and Exynos drivers.
- Errorpath fixes for four different drivers. All on the probe()
errorpath.
- Make the debugfs code for pin config take the right mutex.
* tag 'pinctrl-fixes-v3.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinconf: take the right mutex
pinctrl: sunxi: fix error return code in sunxi_pinctrl_probe()
pinctrl: exynos: Handle suspend/resume of GPIO EINT registers
pinctrl: samsung: Allow per-bank SoC-specific private data
pinctrl: samsung: Add support for SoC-specific suspend/resume callbacks
pinctrl: Don't override the error code in probe error handling
ARM: EXYNOS: Fix EINT wake-up mask configuration when pinctrl is used
pinctrl: exynos: Add support for set_irq_wake of wake-up EINTs
pinctrl: samsung: fix suspend/resume functionality
With the addition of a DVO clock, a bug is now evident in the vt8500
clock code:
[ 0.290000] WARNING: at init/main.c:698 do_one_initcall+0x158/0x18c()
[ 0.300000] initcall wm8505fb_driver_init+0x0/0xc returned with disabled int
This is caused by an unbalanced spinlock in vt8500_dclk_set_rate().
Replace the second call to spin_lock_irqsave() with spin_unlock_irqrestore().
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clock-frequency property from platform data was read but never used.
Apply defined rate when clock is registered.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: add missing changelog]
Cc: stable@kernel.org
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rate was incorrectly computed because we read from wrong divider register.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
Move the private set_auxcr/get_auxcr functions from
drivers/cpuidle/cpuidle-calxeda.c so they can be used across platforms.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This provides cci_enable_port_for_self(). This is the counterpart to
cci_disable_port_by_cpu(self).
This is meant to be called from the MCPM machine specific power_up_setup
callback code when the appropriate affinity level needs to be initialized.
The code therefore has to be position independent as the MMU is still off
and it cannot rely on any stack space.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
On ARM multi-cluster systems coherency between cores running on
different clusters is managed by the cache-coherent interconnect (CCI).
It allows broadcasting of TLB invalidates and memory barriers and it
guarantees cache coherency at system level through snooping of slave
interfaces connected to it.
This patch enables the basic infrastructure required in Linux to handle and
programme the CCI component.
Non-local variables used by the CCI management functions called by power
down function calls after disabling the cache must be flushed out to main
memory in advance, otherwise incoherency of those values may occur if they
are sitting in the cache of some other CPU when power down functions
execute. Driver code ensures that relevant data structures are flushed
from inner and outer caches after the driver probe is completed.
CCI slave port resources are linked to set of CPUs through bus masters
phandle properties that link the interface resources to masters node in
the device tree.
Documentation describing the CCI DT bindings is provided with the patch.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Switch from function-centric to soc-centric clock drivers now makes
a bunch of files obsolete. This deletes all files and Kconfig options
that are not required anymore.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Apparently we should not free page that has not been allocated.
This is b/c alloc_xenballooned_pages will take care of freeing
the page on its own.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Jiri writes:
please pull from
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/linux-block.git for-jens
to receive one pktcdvd fix. It fixes a highly theoretical issue with using.
pktcdvd to work with media that'd be larger than 2TB :) But it's a correct.
fix and makes static checkers shut up about improperly cleaning upper.
32bits.
This is moving core clock and clock gating init for Armada XP to
its own file and adds a Kconfig option. Also init functions are added
and declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is moving core clock and clock gating init for Armada 370 to
its own file and adds a Kconfig option. Also init functions are added
and declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is moving core clock and clock gating init for Kirkwood to its
own file and adds a Kconfig option. Also init functions are added and
declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is moving core clock and clock gating init for Dove to its own
file and adds a Kconfig option. Also init functions are added and
declared so they get called on of_clk_init.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Based on the current common functions for core clocks and clock
gating control, new common functions are joined in a single file.
Given the opportunity, names of functions and structs are unified,
and also a Kconfig entry is added.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Clock gates found on MVEBU SoCs get registered by a common function.
To allow specific SoCs to provide tweaks introduce flags to the clock
gate descriptor instead of filling up the common function SoC specific
tweaks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently no driver *) handles the sysreg clock, with an assumption
that this clock is always left in its default state (enabled).
Before commit 6e6aac7590
ARM: EXYNOS: Migrate clock support to common clock framework
the sysreg clock was not even defined and hence wasn't handled
explicitly in the kernel.
To restore the previous behaviour disable masking the sysreg clock
off in the clock core by default.
*) Except the Exynos4x12 FIMC-IS driver, which will be modified
to not touch the sysreg clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix clk_reg_sysctrl() to set main clock registers of new struct
clk_sysctrl even if the registered clock has no parents.
This fixes an issue where "ulpclk" was registered with all clk->reg_*
fields uninitialized, causing a -EINVAL error from clk_prepare().
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
First Ethernet device has a ".0" appended onto the device name. It
appears that we need this in order to obtain the correct clock.
Without this fix Ethernet does not function on Ux500 devices, which is a
regression.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: improved changelog]
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This narrows the scope of the apple re-POST hack added in:
drm/radeon: re-POST the asic on Apple hardware when booted via EFI
That patch prevents UVD from working on macs when booted in EFI
mode. The original patch fixed macbook2,1 systems which were
r5xx and hence have no UVD. Limit the hack to those systems to
prevent UVD breakage on newer systems.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
Newer asics have variable numbers of crtcs. Use that
rather than the asic family to determine which crtcs
to check. This avoids checking non-existent crtcs or
missing crtcs on certain asics.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The chip id for SUMO2 isn't used.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Tested-By: Dave Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Static checkers complain about widening the binary "not" operations here
because sectors are u64 and "(pd)->settings.size" is unsigned int.
It unintentionally clears the high 32 bits of the sector. This means
that the driver won't work for devices with over 2TB of space. Since
this is a DVD drive, we're unlikely to reach that limit, but we may as
well silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Save the xenstore local status computed in xenbus_init. It can then be used
later to check if xenstored is running in this domain.
Signed-off-by: Aurelien Chartier <aurelien.chartier@citrix.com>
[Changes in v4:
- Change variable name to xen_store_domain_type]
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If the xenbus frontend is located in a domain running xenstored, the device
resume is hanging because it is happening before the process resume. This
patch adds extra logic to the resume code to check if we are the domain
running xenstored and delay the resume if needed.
Signed-off-by: Aurelien Chartier <aurelien.chartier@citrix.com>
[Changes in v2:
- Instead of bypassing the resume, process it in a workqueue]
[Changes in v3:
- Add a struct work in xenbus_device to avoid dynamic allocation
- Several small code fixes]
[Changes in v4:
- Use a dedicated workqueue]
[Changes in v5:
- Move create_workqueue error handling to xenbus_frontend_dev_resume]
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Increase the current arbitrary limit for isocronous packet size to a
value large enough to account for USB 3.0 super bandwidth streams,
bMaxBurst (0~15 allowed, 1~16 packets)
bmAttributes (bit 1:0, mult 0~2, 1~3 packets)
so the size max for one USB 3 isocronous transfer is
1024 byte * 16 * 3 = 49152 byte
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Federico Manzan <f.manzan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent
device. This will result a mismatch between the number the queues in netdev and
tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was
not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues
later, netif_set_real_num_tx_queues() may fail which result a single queue
netdevice with multiple sockets attached.
Solve this by disallowing changing the mq flag for persistent device.
Bug was introduced by commit edfb6a148c
(tuntap: reduce memory using of queues).
Reported-by: Sriram Narasimhan <sriram.narasimhan@hp.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts commit 3e619d0415
(USB: EHCI: fix bug in scheduling periodic split transfers). The
commit was valid -- it fixed a real bug -- but the periodic scheduler
in ehci-hcd is in such bad shape (especially the part that handles
split transactions) that fixing one bug is very likely to cause
another to surface. That's what happened in this case; the result was
choppy and noisy playback on certain 24-bit audio devices.
The only real fix will be to rewrite this entire section of code. My
next project...
This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1136110.
Thanks to Tim Richardson for extra testing and feedback, and to Joseph
Salisbury and Tyson Tan for tracking down the original source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Joseph Salisbury <joseph.salisbury@canonical.com>
CC: Tim Richardson <tim@tim-richardson.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's four xHCI bug fixes that should be queued for 3.10.
The first two are generic bug fixes, and have been in my queue for a while
because I've been doing the OPW internship coordination. I suspect you'll be
seeing more pull requests from me now that the intern selection process is
almost over. :)
The last two patches fix a nasty kernel crash on resume from S3 for TI hosts
that have the compliance mode quirk. Tony has confirmed that the patches fix
the issue on the effected systems.
All four patches are marked for stable.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CwKx
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2013-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Misc bug fixes for 3.10.
Hi Greg,
Here's four xHCI bug fixes that should be queued for 3.10.
The first two are generic bug fixes, and have been in my queue for a while
because I've been doing the OPW internship coordination. I suspect you'll be
seeing more pull requests from me now that the intern selection process is
almost over. :)
The last two patches fix a nasty kernel crash on resume from S3 for TI hosts
that have the compliance mode quirk. Tony has confirmed that the patches fix
the issue on the effected systems.
All four patches are marked for stable.
Sarah Sharp
A third possible PCI ID, as personally observed, and found in the
pci.ids list.
Signed-off-by: George Spelvin <linux@horizon.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In some circumstances setting a 64-bit DMA mask can fail, as explained
in Documentation/DMA-API-HOWTO.txt. Use the recommended code sequence
to set a 32-bit DMA mask if setting a 64-bit DMA mask fails.
Reported-by: Chayan Biswas <Chayan.Biswas@sandisk.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Since highmem PIO URB handling was introduced in:
8e8a551 usb: musb: host: Handle highmem in PIO mode
when a URB is being handled it may happen that the static use_sg flag
was set by a previous URB with buffer in highmem. This leads to error
in handling the present URB.
Fix this by making the use_sg flag URB specific.
Cc: stable <stable@vger.kernel.org> # 3.7+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
we never allocate a TRB pool for physical endpoints
0 and 1 so trying to free it (a invalid TRB pool pointer)
will lead us in a warning while removing dwc3.ko module.
In order to fix the situation, all we have to do is skip
dwc3_free_trb_pool() for physical endpoints 0 and 1 just
as we while deleting endpoints from the endpoints list.
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the glue layer is removed first (core layer later),
it deletes the phy device first, then the core device.
But at core's removal, it still uses PHY's resources, it may
cause kernel's oops. It is much like the problem
Paul Zimmerman reported at:
http://marc.info/?l=linux-usb&m=136547502011472&w=2.
Besides, it is reasonable the PHY is deleted at last as
the controller is the PHY's user.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For p2p client mode powersave mode should be kept disabled. It is
working but inefficient. In general p2p links do no benefit from this
mode, because these links are setup temporarily to transfer data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multi channel support was disabled. This patch will enable it and
configure the P2P GO on the correct frequency when multi channel
is used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon deleting a P2P_CLIENT/GO interface the vif and consequently
the wdev is freed before the net_device is actually being unregistered
but cfg80211 still needs to access the wdev. Using destructor field
to free the net_device and vif.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When registration fails the net device is no longer needed. Free
the net device and remove reference to private data from the
driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the struct brcmf_cfg80211_info instance instead of obtaining
through vif itself using vif->wdev. This is needed as the netdev
associated with this vif is already unregistered.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware requires that on p2p setup when net interfaces
are created or updated that they start initially with the same
channel as the channel in use for the current connection
(if any). If none exists take default channel 11.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ARP offloading should only be used in STA or P2P client mode. It
is currently configured once at init. When being configured for AP
ARP offloading should be turned off and when AP mode is left it can
be turned back on.
Cc: stable@vger.kernel.org
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull drm fixes from Dave Airlie:
"This is mostly exynos and intel fixes, along with some vblank patches
I lost from Rob a few months ago that make wayland work better on lots
of GPUs, also a qxl kconfig fix."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
qxl: fix Kconfig deps - select FB_DEFERRED_IO
drm/exynos: replace request_threaded_irq with devm function
drm/exynos: remove unnecessary devm_kfree
drm/exynos: fix build warnings from ipp fimc
drm/exynos: cleanup device pointer usages
drm/exynos: wait for the completion of pending page flip
drm/exynos: use drm_send_vblank_event() helper
drm/i915: avoid premature DP AUX timeouts
drm/i915: avoid premature timeouts in __wait_seqno()
drm/i915: use msecs_to_jiffies_timeout instead of open coding the same
drm/i915: add msecs_to_jiffies_timeout to guarantee minimum duration
drm/i915: force full modeset if the connector is in DPMS OFF mode
drm/exynos: page flip fixes
drm/exynos: exynos_hdmi: Pass correct pointer to free_irq()
drm/exynos: exynos_drm_ipp: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: exynos_drm_fbdev: Fix incorrect usage of IS_ERR_OR_NULL
drm/imx: use drm_send_vblank_event() helper
drm/shmob: use drm_send_vblank_event() helper
drm/radeon: use drm_send_vblank_event() helper
drm/nouveau: use drm_send_vblank_event() helper
...
Pull crypto fixes from Herbert Xu:
"This push fixes a crash in the new sha256_ssse3 driver as well as a
DMA setup/teardown bug in caam"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sha256_ssse3 - fix stack corruption with SSSE3 and AVX implementations
crypto: caam - fix inconsistent assoc dma mapping direction
In the (not so useful) kernel configuration where CONFIG_SWAP
is undefined and CONFIG_XEN_SELFBALLOONING is defined,
xen_tmem_init would use undefined variable 'static bool frontswap'.
Added #else to have #define frontswap (0) in the case where
CONFIG_FRONTSWAP is not defined.
Signed-off-by: Frederico Cadete <frederico@cadete.eu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The phy_init_eee has to exit with an error when the
local device and its link partner both do not support EEE.
So this patch fixes a problem when verify this.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allow the pci-mvebu driver to be compiled on the Kirkwood platform,
and add the 'marvell,kirkwood-pcie' as a compatible string supported
by the driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The status register of the PCI configuration space of PCI-to-PCI
bridges contain some read-only bits, and so write-1-to-clear bits. So,
the Linux PCI core sometimes writes 0xffff to this status register,
and in the current PCI-to-PCI bridge emulation code of the Marvell
driver, we do take all those 1s being written. Even the read-only bits
are being overwritten.
For now, all the read-only bits should be emulated to have the zero
value.
The other bits, that are write-1-to-clear bits are used to report
various kind of errors, and are never set by the emulated bridge, so
there is no need to support this write-1-to-clear bits mechanism.
As a conclusion, the easiest solution is to simply emulate this status
register by returning zero when read, and ignore the writes to it.
This has two visible effects:
* The devsel is no longer 'unknown' in, i.e
Flags: bus master, 66MHz, user-definable features, ?? devsel, latency 0
becomes:
Flags: bus master, 66MHz, user-definable features, fast devsel, latency 0
in lspci -v.
This was caused by a value of 11b being read for devsel, which is
an invalid value. This 11b value being read was due to a previous
write of 0xffff into the status register.
* The capability list is no longer broken, because we indicate to the
Linux PCI core that we don't have a Capabilities Pointer in the PCI
configuration space of this bridge. The following message is
therefore no longer visible in lspci -v:
Capabilities: [fc] <chain broken>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Until now, the Marvell PCIe driver was only allowing the enumeration
of the devices in the secondary bus of the emulated PCI-to-PCI
bridge. This works fine when a PCIe device is directly connected into
a PCIe slot of the Marvell board.
However, when the device connected in the PCIe slot is a physical PCIe
bridge, beyond which a real PCIe device is connected, it no longer
worked, as the driver was preventing the Linux PCI core from seeing
such devices.
This commit fixes that by ensuring that configuration transactions on
subordinate busses are properly forwarded on the right PCIe interface.
Thanks to this patch, a PCIe card beyond a PCIe bridge, itself beyond
the emulated PCI-to-PCI bridge is properly detected, with the
following layout:
-[0000:00]-+-01.0-[01]----00.0
+-09.0-[02-07]----00.0-[03-07]--+-01.0-[04]--
| +-05.0-[05]--
| +-07.0-[06]--
| \-09.0-[07]----00.0
\-0a.0-[08]----00.0
Where the PCIe interface that sits beyond the emulated PCI-to-PCI
bridge at 09.0 allows to access the secondary bus 02, on which there
is a PCIe bridge that allows to access the 3 to 7 busses, that are
subordinates to this bridge. And on one of this bus (bus 7), there is
one real PCIe device connected.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
By default, the Marvell hardware, for each PCIe interface, exhibits
the following devices:
* On slot 0, a "Marvell Memory controller", identical on all PCIe
interfaces, and which isn't useful when the Marvell SoC is the PCIe
root complex (i.e, the normal case when we run Linux on the Marvell
SoC).
* On slot 1, the real PCIe card connected into the PCIe slot of the
board.
So, what the Marvell PCIe driver was doing in its PCI-to-PCI bridge
emulation is that when the Linux PCI core was trying to access the
device in slot 0, we were in fact forwarding the configuration
transaction to the device in slot 1. For all other slots, we were
telling the Linux PCI core that there was no device connected.
However, new versions of bootloaders from Marvell change the default
PCIe configuration, and make the real device appear in slot 0, and the
"Marvell Memory controller" in slot 1.
Therefore, this commit modifies the Marvell PCIe driver to adjust the
PCIe hardware configuration to make sure that this behavior (real
device in slot 0, "Marvell Memory controller" in slot 1) is the one
we'll see regardless of what the bootloader has done. It allows to
remove the little hack that was forwarding configuration transactions
on slot 0 to slot 1, which is nice.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In case of error, function of_clk_get_by_name() returns
ERR_PTR() never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The pm runtime reference counting of the driver is broken for the case
when there is more than one transfer queued, leading to the device being
runtime suspend while active. Fix it.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pinconf_dgb_config_print() takes the per-pincontroller
mutex, when what it wants to take is actually the pin maps
mutex.
Reported-by: James Hogan <james.hogan@imgtec.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix to return a negative error code from the devm_clk_get() error
handling case instead of 0, as done elsewhere in this function.
Introduced by commit 950707c0eb
(pinctrl: sunxi: add clock support)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO EINT control registers needs to be preserved across
suspend/resume cycle. This patch extends the driver to take care of
this.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch extends pin bank descriptor structure with SoC-specific
private data field that allows SoC-specific drivers to store their own
private data.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SoC-specific driver might require additional save and restore of
registers. This patch adds pair of SoC-specific callbacks per pinctrl
device to account for this.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise, we return 0 in probe error paths when gpiochip_remove() returns 0.
Also show error message if gpiochip_remove() fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support of IRQ wake-up ability configuration for
wake-up EINTs on Exynos SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO states need to be restored after s2r and this is not currently
supported in the pinctrl driver. This patch saves the gpio states before
suspend and restores them after resume.
Saving and restoring is done very early using syscore_ops and must
happen before pins are released from their powerdown state.
Patch originally from Prathyush K <prathyush.k@samsung.com> but
rewritten by Doug Anderson <dianders@chromium.org>.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In 63b77bf489
iwlwifi: dvm: don't send zeroed LQ cmd
I tried to avoid to send zeroed LQ cmd, but I made a (very)
stupid mistake in the memcmp.
Since this patch has been ported to stable, the fix should
go to stable too.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341
Cc: stable@vger.kernel.org
Reported-by: Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Add a clock controller driver and documentation.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
MMC driver probe will abort for DT case because of failed
platform_get_resource_byname() lookup. Fix it by skipping resource
lookup byname for device tree build.
Issue is hidden because hwmod populates the IO resources which
helps to succeed platform_get_resource_byname() and probe.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert dmaengine channel requests to use
dma_request_slave_channel_compat(). This supports platforms booting
with or without DT populated.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Otherwise SDIO cards won't necessarily work when booted with
device tree as we will never power down the SDIO cards. This
means the SDIO card reset does not happen which at least some
WLAN controllers expect to happen with ifconfig wlan0 down.
The PBIAS voltage is only available for the first controller
instance, so let's limit the PBIAS workaround to the first
controller only.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add three more ACPI HIDs. Also, as some devices must be
further distinguished by ACPI UID, slot information is now
associated with HID and UID.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use generic DMA DT helper. Platforms booting with or without DT populated
are both supported.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The eSDHC controller on the i.MX53 needs an additional, non spec
compliant CMD12 after a multiblock read with a predefined number of
blocks. Otherwise the internal state machine won't go back to the
idle state.
This commit effectively reverts 5b6b0ad6 (mmc: sdhci-esdhc-imx:
fix for mmc cards on i.MX5), which fixed part of the problem by
making multiblock reads work, however this fix was not sufficient
when multi- and singleblock reads got intermixed.
This implements the recommended workaround (Freescale i.MX Reference
Manual, section 29.6.8 "Multi-block Read") by manually sending a
CMD12 with the RSPTYP bits cleared.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently SDIO interrupts do not work on i.MX53 and maybe others.
This was observed with a Marvell 8787 based SDIO wifi adapter
using the mwifiex driver and firmware from the Marvell git
repository.
The symptom was a timeout after firmware download.
Observing the SDIO_DAT1 line showed that an interrupt was requested
(level 0) but no interrupt was generated in software, the line
stayed low until a timeout ocurred and the card was reset.
There is a Freescale errata
ENGcm11186 "eSDHC misses SDIO interrupt when CINT is disabled"
The workaround suggested by this errata is already implemented and
involves clearing and then setting the D3CD bit in the host control
register [see esdhc_writel_le()]
However, when esdhc_writeb_le() is later used to write to
SDHCI_HOST_CONTROL it always resets the D3CD bit.
To fix this simply add the D3CD bit to the set of bits
not modified by esdhc_writeb_le().
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull parisc fixes from Helge Deller:
"This time we made the kernel- and interruption stack allocation
reentrant which fixed some strange kernel crashes (specifically
protection ID traps).
Furthemore this patchset fixes the interrupt stack in UP and SMP
configurations by using native locking instructions. And finally
usage of floating point calculations on parisc were disabled in the
MPILIB."
* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix irq stack on UP and SMP
parisc/superio: Use module_pci_driver to register driver
parisc: make interrupt and interruption stack allocation reentrant
parisc: show number of FPE and unaligned access handler calls in /proc/interrupts
parisc: add additional parisc git tree to MAINTAINERS file
parisc: use PAGE_SHIFT instead of hardcoded value 12 in pacache.S
parisc: add rp5470 entry to machine database
MPILIB: disable usage of floating point registers on parisc
Fix to release resources when ptp_clock_register() fail instead
of return error code directly.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function
qlge_probe() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J. Wysocki.
- New ACPI video blacklist item from Bastian Triller.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Srt8
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J Wysocki.
- New ACPI video blacklist item from Bastian Triller.
* tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
cpufreq: arm_big_little_dt: Instantiate as platform_driver
cpufreq: arm_big_little_dt: Register driver only if DT has valid data
cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
cpufreq / intel_pstate: Add additional supported CPU ID
cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT
ACPI / PM: Allow device power states to be used for CONFIG_PM unset
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
Merge fixes from Andrew Morton:
"A bunch of fixes and one simple fbdev driver which missed the merge
window because people will still talking about it (to no great
effect)."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (30 commits)
aio: fix kioctx not being freed after cancellation at exit time
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
random: fix accounting race condition with lockless irq entropy_count update
drivers/char/random.c: fix priming of last_data
mm/memory_hotplug.c: fix printk format warnings
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
drivers/block/brd.c: fix brd_lookup_page() race
fbdev: FB_GOLDFISH should depend on HAS_DMA
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
auditfilter.c: fix kernel-doc warnings
aio: fix io_getevents documentation
revert "selftest: add simple test for soft-dirty bit"
drivers/leds/leds-ot200.c: fix error caused by shifted mask
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
linux/kernel.h: fix kernel-doc warning
mm compaction: fix of improper cache flush in migration code
rapidio/tsi721: fix bug in MSI interrupt handling
hfs: avoid crash in hfs_bnode_create
...
We didn't have any fixes sent up for -rc2, so this is a slightly larger
batch. A bit all over the place platform-wise; OMAP, at91, marvell,
renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig updates
due to new/changing options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8tMi
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have any fixes sent up for -rc2, so this is a slightly
larger batch. A bit all over the place platform-wise; OMAP, at91,
marvell, renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig
updates due to new/changing options."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
ARM: shmobile: marzen: Use error values in usb_power_*
ARM: tegra: defconfig fixes
ARM: nomadik: fix IRQ assignment for SMC ethernet
ARM: vt8500: Add missing NULL terminator in dt_compat
clk: tegra: add ac97 controller clock
clk: tegra: remove USB from clk init table
ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
ARM: plat-orion: Fix num_resources and id for ge10 and ge11
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
arm: mvebu: fix the 'ranges' property to handle PCIe
ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
...
Currently the driver can crash with a NULL pointer dereference if no
pdata is provided, despite of successful registration of the MFD part.
This patch fixes the problem by adding a NULL check before dereferencing
the pdata pointer.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 902c098a36 ("random: use lockless techniques in the interrupt
path") turned IRQ path from being spinlock protected into lockless
cmpxchg-retry update.
That commit removed r->lock serialization between crediting entropy bits
from IRQ context and accounting when extracting entropy on userspace
read path, but didn't turn the r->entropy_count reads/updates in
account() to use cmpxchg as well.
It has been observed, that under certain circumstances this leads to
read() on /dev/urandom to return 0 (EOF), as r->entropy_count gets
corrupted and becomes negative, which in turn results in propagating 0
all the way from account() to the actual read() call.
Convert the accounting code to be the proper lockless counterpart of
what has been partially done by 902c098a36.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ec8f02da9e ("random: prime last_data value per fips
requirements") added priming of last_data per fips requirements.
Unfortuantely, it did so in a way that can lead to multiple threads all
incrementing nbytes, but only one actually doing anything with the extra
data, which leads to some fun random corruption and panics.
The fix is to simply do everything needed to prime last_data in a single
shot, so there's no window for multiple cpus to increment nbytes -- in
fact, we won't even increment or decrement nbytes anymore, we'll just
extract the needed EXTRACT_SIZE one time per pool and then carry on with
the normal routine.
All these changes have been tested across multiple hosts and
architectures where panics were previously encoutered. The code changes
are are strictly limited to areas only touched when when booted in fips
mode.
This change should also go into 3.8-stable, to make the myriads of fips
users on 3.8.x happy.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stodola <jstodola@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The index on the page must be set before it is inserted in the radix
tree. Otherwise there is a small race which can occur during lookup
where the page can be found with the incorrect index. This will trigger
the BUG_ON() in brd_lookup_page().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Chris Wedgwood <cw@f00f.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `goldfish_fb_remove':
drivers/video/goldfishfb.c:301: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `goldfish_fb_probe':
drivers/video/goldfishfb.c:247: undefined reference to `dma_alloc_coherent'
drivers/video/goldfishfb.c:280: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
free_irq() expects the same pointer that was passed to request_irq(),
otherwise the IRQ is not freed.
The issue was found using the following coccinelle script:
<smpl>
@r1@
type T;
T devid;
@@
request_irq(..., devid)
@r2@
type r1.T;
T devid;
position p;
@@
free_irq@p(..., devid)
@@
position p != r2.p;
@@
*free_irq@p(...)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this
problem was found. It turned out that the released register
documentation is wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix bug in MSI interrupt handling which causes loss of event
notifications.
Typical indication of lost MSI interrupts are stalled message and
doorbell transfers between RapidIO endpoints. To avoid loss of MSI
interrupts all interrupts from the device must be disabled on entering
the interrupt handler routine and re-enabled when exiting it.
Re-enabling device interrupts will trigger new MSI message(s) if Tsi721
registered new events since entering interrupt handler routine.
This patch is applicable to kernel versions starting from v3.2.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Hennerich