None of the BlueFRITZ! devices with manufacurer ID 31 (AVM Berlin)
support HCI_Read_Local_Supported_Commands. It is safe to use the
manufacturer ID (instead of e.g. a USB ID specific quirk) because the
company never created any newer controllers.
< HCI Command: Read Local Supported Comm.. (0x04|0x0002) plen 0 [hci0] 0.210014
> HCI Event: Command Status (0x0f) plen 4 [hci0] 0.217361
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Unknown HCI Command (0x01)
Reported-by: Jörg Esser <jackfritt@boh.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Jörg Esser <jackfritt@boh.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If hci_dev_open() is called after hci_register_dev() added the device to
the hci_dev_list but before the workqueue are created we could run into a
NULL pointer dereference (see below).
This bug is very unlikely to happen, systems using bluetoothd to
manage their bluetooth devices will never see this happen.
BUG: unable to handle kernel NULL pointer dereference
0100
IP: [<ffffffff81077502>] __queue_work+0x32/0x3d0
(...)
Call Trace:
[<ffffffff81077be5>] queue_work_on+0x45/0x50
[<ffffffffa016e8ff>] hci_req_run+0xbf/0xf0 [bluetooth]
[<ffffffffa01709b0>] ? hci_init2_req+0x720/0x720 [bluetooth]
[<ffffffffa016ea06>] __hci_req_sync+0xd6/0x1c0 [bluetooth]
[<ffffffff8108ee10>] ? try_to_wake_up+0x2b0/0x2b0
[<ffffffff8150e3f0>] ? usb_autopm_put_interface+0x30/0x40
[<ffffffffa016fad5>] hci_dev_open+0x275/0x2e0 [bluetooth]
[<ffffffffa0182752>] hci_sock_ioctl+0x1f2/0x3f0 [bluetooth]
[<ffffffff815c6050>] sock_do_ioctl+0x30/0x70
[<ffffffff815c75f9>] sock_ioctl+0x79/0x2f0
[<ffffffff811a8046>] do_vfs_ioctl+0x96/0x560
[<ffffffff811a85a1>] SyS_ioctl+0x91/0xb0
[<ffffffff816d989d>] system_call_fastpath+0x1a/0x1f
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The length check is invalid since the length varies with type of
info response.
This was introduced by the commit cb3b3152b2
Because of this, l2cap info rsp is not handled and command reject is sent.
> ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Info rsp: type 2 result 0
Extended feature mask 0x00b8
Enhanced Retransmission mode
Streaming mode
FCS Option
Fixed Channels
< ACL data: handle 11 flags 0x00 dlen 10
L2CAP(s): Command rej: reason 0
Command not understood
Cc: stable@vger.kernel.org
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Chan-Yeol Park <chanyeol.park@samsung.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even though the HCI_Delete_Stored_Link_Key command is mandatory for 1.1
and later controllers some controllers do not seem to support it
properly as was witnessed by one Broadcom based controller:
< HCI Command: Delete Stored Link Key (0x03|0x0012) plen 7
bdaddr 00:00:00:00:00:00 all 1
> HCI Event: Command Complete (0x0e) plen 4
Delete Stored Link Key (0x03|0x0012) ncmd 1
status 0x11 deleted 0
Error: Unsupported Feature or Parameter Value
Luckily this same controller also doesn't list the command in its
supported commands bit mask (counting from 0 bit 7 of octet 6):
< HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
> HCI Event: Command Complete (0x0e) plen 68
Read Local Supported Commands (0x04|0x0002) ncmd 1
status 0x00
Commands: ffffffffffff1ffffffffffff30fffff3f
Therefore, it makes sense to move sending of HCI_Delete_Stored_Link_Key
to after receiving the supported commands response and to only send it
if its respective bit in the mask is set. The downside of this is that
we no longer send the HCI_Delete_Stored_Link_Key command for Bluetooth
1.1 controllers since HCI_Read_Local_Supported_Command was introduced in
version 1.2, but this is an acceptable penalty as the command in
question shouldn't affect critical behavior.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There has been code in place to check that the L2CAP length header
matches the amount of data received, but many PDU handlers have not been
checking that the data received actually matches that expected by the
specific PDU. This patch adds passing the length header to the specific
handler functions and ensures that those functions fail cleanly in the
case of an incorrect amount of data.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LE-only controllers do not support extended features so any kind of host
feature bit checks do not make sense for them. This patch fixes code
used for both single-mode (LE-only) and dual-mode (BR/EDR/LE) to use the
HCI_LE_ENABLED flag instead of the "Host LE supported" feature bit for
LE support tests.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The order of parameters was mixed up, introduced in commit
"mac80211: improve the rate control API"
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a CAC is running and stop_ap is called (e.g. when hostapd is killed
while performing CAC), the CAC must be aborted immediately.
Otherwise ieee80211_stop_ap() will try to stop it when it's too late -
wdev->channel is already NULL and the abort event can not be generated.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some APs, notably 2G/3G/4G Wifi routers, specifically the
"Onda PN51T", "Vodafone PocketWiFi 2", "ZTE MF60" and a similar
T-Mobile branded device [1] that erroneously don't include all the
needed information in (re)association response frames. Work around
this by assuming the information is the same as it was in the
beacon or probe response and using the data from there instead.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58881.
[1] https://bbs.archlinux.org/viewtopic.php?pid=1277305
Note that this requires marking the first ieee802_11_parse_elems()
argument const, otherwise we'd get a compiler warning.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Michal Zajac <manwe@manwe.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing the MAC address of a single vif mac80211 will check if
the new address fits into the address mask specified by the driver.
This only needs to be done when using multiple BSSIDs. Hence, check
the new address only against all other vifs.
Also fix the MAC address assignment on new interfaces if the user
changed the address of a vif such that perm_addr is not covered by
addr_mask anymore.
Resolves:
https://bugzilla.kernel.org/show_bug.cgi?id=57371
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Cc: Bruno Randolf <br1@thinktube.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since Eric's commit efe117ab8 ("Speedup ieee80211_remove_interfaces")
there's a bug in mac80211 when it unregisters with AP_VLAN interfaces
up. If the AP_VLAN interface was registered after the AP it belongs
to (which is the typical case) and then we get into this code path,
unregister_netdevice_many() will crash because it isn't prepared to
deal with interfaces being closed in the middle of it. Exactly this
happens though, because we iterate the list, find the AP master this
AP_VLAN belongs to and dev_close() the dependent VLANs. After this,
unregister_netdevice_many() won't pick up the fact that the AP_VLAN
is already down and will do it again, causing a crash.
Cc: stable@vger.kernel.org [2.6.33+]
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of code in mac80211 assumes that the hw queues are
set up correctly for all interfaces (except for monitor)
but this isn't true for AP_VLAN interfaces. Fix this by
copying the AP master configuration when an AP VLAN is
brought up, after this the AP interface can't change its
configuration any more and needs to be brought down to
change it, which also forces AP_VLAN interfaces down, so
just copying in open() is sufficient.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code I added in "mac80211: don't start new netdev queues
if driver stopped" crashes for monitor and AP VLAN interfaces
because while they have a netdev, they don't have queues set
up by the driver.
To fix the crash, exclude these from queue accounting here
and just start their netdev queues unconditionally.
For monitor, this is the best we can do, as we can redirect
frames there to any other interface and don't know which one
that will since it can be different for each frame.
For AP VLAN interfaces, we can do better later and actually
properly track the queue status. Not doing this is really a
separate bug though.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Kconfig symbol NFC_LLCP was removed in commit 30cc458765 ("NFC: Move
LLCP code to the NFC top level diirectory"). But the reference to its
macro in this Makefile was only commented out. Remove it now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We send direct probe to broadcast address, as some APs do not respond to
unicast PROBE frames when unassociated. Broadcast frames are not acked,
so we can not use that for trigger MLME state machine, but we need to
use old timeout mechanism.
This fixes authentication timed out like below:
[ 1024.671974] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 1024.694125] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 1024.695450] wlan6: direct probe to 54:e6:fc:98:63:fe (try 2/3)
[ 1024.700586] wlan6: send auth to 54:e6:fc:98:63:fe (try 3/3)
[ 1024.701441] wlan6: authentication with 54:e6:fc:98:63:fe timed out
With fix, we have:
[ 4524.198978] wlan6: authenticate with 54:e6:fc:98:63:fe
[ 4524.220692] wlan6: direct probe to 54:e6:fc:98:63:fe (try 1/3)
[ 4524.421784] wlan6: send auth to 54:e6:fc:98:63:fe (try 2/3)
[ 4524.423272] wlan6: authenticated
[ 4524.423811] wlan6: associate with 54:e6:fc:98:63:fe (try 1/3)
[ 4524.427492] wlan6: RX AssocResp from 54:e6:fc:98:63:fe (capab=0x431 status=0 aid=1)
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if the frame isn't transmitted to the AP, we need to
report it to cfg80211 so the state there can be updated
correctly.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the interface goes down, there's no need to call
cfg80211_mlme_down() after __cfg80211_disconnect() as
the latter will call the former (if appropriate.)
Also, in __cfg80211_disconnect(), if the cfg80211 SME
isn't used, __cfg80211_disconnected() may still need
to be called (depending on the current state) so that
the SME state gets cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, ignore frames with mis-matched BSSID that aren't
multicast or sent to the correct destination. This fixes
reporting public action frames to userspace multiple times
on multiple virtual AP interfaces.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the attributes fixes an issue with P2P Device not
working properly for management frame TX.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_get_tkip_p2k() may be called with interrupts
disabled, so spin_unlock_bh() isn't safe and leads to
warnings. Since it's always called with BHs disabled
already, just use spin_lock().
Cc: stable@vger.kernel.org
Reported-by: Milan Kocian <milon@wq.cz>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Document rx vs tx status concurrency requirements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an HT AP is advertising channel switch in a beacon, it
doesn't (and shouldn't, according to 802.11-2012 Table 8-20)
include a secondary channel offset element. The only possible
interpretation is that the previous secondary channel offset
remains valid, so use that when switching channel based only
on beacon information.
VHT requires the Wide Bandwidth Channel Switch subelement to
be present in the Channel Switch Wrapper element, so the code
for that is probably ok (see 802.11ac Draft 4, 8.4.2.165.)
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 12e7f51702,
IEEE80211_SDATA_DISCONNECT_RESUME no longer worked as
it would simply never be tested. Restore a bit of the
code removed there and in 9b7d72c104
to make it work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device reports a non-wireless wakeup reason, the
tracing code crashes trying to dereference a NULL pointer.
Fix this by checking the pointer on all accesses and also
add a non_wireless tag to the event.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If rfkill_register() fails in wiphy_register() the struct device
is unregistered but everything else isn't (regulatory, debugfs)
and we even leave the wiphy instance on all internal lists even
though it will likely be freed soon, which is clearly a problem.
Fix this by cleaning up properly.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Ensure that we match the 'sec=' mount flavour against the server list
- Fix the NFSv4 byte range locking in the presence of delegations
- Ensure that we conform to the NFSv4.1 spec w.r.t. freeing lock stateids
- Fix a pNFS data server connection race
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=5zpc
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client bugfixes from Trond Myklebust:
- Ensure that we match the 'sec=' mount flavour against the server list
- Fix the NFSv4 byte range locking in the presence of delegations
- Ensure that we conform to the NFSv4.1 spec w.r.t. freeing lock
stateids
- Fix a pNFS data server connection race
* tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4.1 Fix data server connection race
NFSv3: match sec= flavor against server list
NFSv4.1: Ensure that we free the lock stateid on the server
NFSv4: Convert nfs41_free_stateid to use an asynchronous RPC call
SUNRPC: Don't spam syslog with "Pseudoflavor not found" messages
NFSv4.x: Fix handling of partially delegated locks
Rather than having logic to calculate inner protocol in every
tunnel gso handler move it to gso code. This simplifies code.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cong Wang <amwang@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Just a small pile of fixes"
1) Fix race conditions in IP fragmentation LRU list handling, from
Konstantin Khlebnikov.
2) vfree() is no longer verboten in interrupts, so deferring is
pointless, from Al Viro.
3) Conversion from mutex to semaphore in netpoll left trylock test
inverted, caught by Dan Carpenter.
4) 3c59x uses wrong base address when releasing regions, from Sergei
Shtylyov.
5) Bounds checking in TIPC from Dan Carpenter.
6) Fastopen cookies should not be expired as aggressively as other TCP
metrics. From Eric Dumazet.
7) Fix retrieval of MAC address in ibmveth, from Ben Herrenschmidt.
8) Don't use "u16" in virtio user headers, from Stephen Hemminger
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
tipc: potential divide by zero in tipc_link_recv_fragment()
tipc: add a bounds check in link_recv_changeover_msg()
net/usb: new driver for RTL8152
3c59x: fix freeing nonexistent resource on driver unload
netpoll: inverted down_trylock() test
rps_dev_flow_table_release(): no need to delay vfree()
fib_trie: no need to delay vfree()
net: frag, fix race conditions in LRU list maintenance
tcp: do not expire TCP fastopen cookies
net/eth/ibmveth: Fixup retrieval of MAC address
virtio: don't expose u16 in userspace api
The worry here is that fragm_sz could be zero since it comes from
skb->data.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bearer_id here comes from skb->data and it can be a number from 0 to
7. The problem is that the ->links[] array has only 2 elements so I
have added a range check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Ceph changes from Alex Elder:
"This is a big pull.
Most of it is culmination of Alex's work to implement RBD image
layering, which is now complete (yay!).
There is also some work from Yan to fix i_mutex behavior surrounding
writes in cephfs, a sync write fix, a fix for RBD images that get
resized while they are mapped, and a few patches from me that resolve
annoying auth warnings and fix several bugs in the ceph auth code."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (254 commits)
rbd: fix image request leak on parent read
libceph: use slab cache for osd client requests
libceph: allocate ceph message data with a slab allocator
libceph: allocate ceph messages with a slab allocator
rbd: allocate image object names with a slab allocator
rbd: allocate object requests with a slab allocator
rbd: allocate name separate from obj_request
rbd: allocate image requests with a slab allocator
rbd: use binary search for snapshot lookup
rbd: clear EXISTS flag if mapped snapshot disappears
rbd: kill off the snapshot list
rbd: define rbd_snap_size() and rbd_snap_features()
rbd: use snap_id not index to look up snap info
rbd: look up snapshot name in names buffer
rbd: drop obj_request->version
rbd: drop rbd_obj_method_sync() version parameter
rbd: more version parameter removal
rbd: get rid of some version parameters
rbd: stop tracking header object version
rbd: snap names are pointer to constant data
...
The return value is reversed from mutex_trylock().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same story as with fib_trie patch - vfree() from RCU callbacks
is legitimate now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that vfree() can be called from interrupt contexts, there's no
need to play games with schedule_work() to escape calling vfree()
from RCU callbacks.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP metric cache expires entries after one hour.
This probably make sense for TCP RTT/RTTVAR/CWND, but not
for TCP fastopen cookies.
Its better to try previous cookie. If it appears to be obsolete,
server will send us new cookie anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several routines do not use netdev_features_t to hold such bitmasks,
fixes from Patrick McHardy and Bjørn Mork.
2) Update cpsw IRQ software state and the actual HW irq enabling in the
correct order. From Mugunthan V N.
3) When sending tipc packets to multiple bearers, we have to make
copies of the SKB rather than just giving the original SKB directly.
Fix from Gerlando Falauto.
4) Fix race with bridging topology change timer, from Stephen
Hemminger.
5) Fix TCPv6 segmentation handling in GRE and VXLAN, from Pravin B
Shelar.
6) Endian bug in USB pegasus driver, from Dan Carpenter.
7) Fix crashes on MTU reduction in USB asix driver, from Holger
Eitzenberger.
8) Don't allow the kernel to BUG() just because the user puts some crap
in an AF_PACKET mmap() ring descriptor. Fix from Daniel Borkmann.
9) Don't use variable sized arrays on the stack in xen-netback, from
Wei Liu.
10) Fix stats reporting and an unbalanced napi_disable() in be2net
driver. From Somnath Kotur and Ajit Khaparde.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
cxgb4: fix error recovery when t4_fw_hello returns a positive value
sky2: Fix crash on receiving VLAN frames
packet: tpacket_v3: do not trigger bug() on wrong header status
asix: fix BUG in receive path when lowering MTU
net: qmi_wwan: Add Telewell TW-LTE 4G
usbnet: pegasus: endian bug in write_mii_word()
vxlan: Fix TCPv6 segmentation.
gre: Fix GREv4 TCPv6 segmentation.
bridge: fix race with topology change timer
tipc: pskb_copy() buffers when sending on more than one bearer
tipc: tipc_bcbearer_send(): simplify bearer selection
tipc: cosmetic: clean up comments and break a long line
drivers: net: cpsw: irq not disabled in cpsw isr in particular sequence
xen-netback: better names for thresholds
xen-netback: avoid allocating variable size array on stack
xen-netback: remove redundent parameter in netbk_count_requests
be2net: Fix to fail probe if MSI-X enable fails for a VF
be2net: avoid napi_disable() when it has not been enabled
be2net: Fix firmware download for Lancer
be2net: Fix to receive Multicast Packets when Promiscuous mode is enabled on certain devices
...
Jakub reported that it is fairly easy to trigger the BUG() macro
from user space with TPACKET_V3's RX_RING by just giving a wrong
header status flag. We already had a similar situation in commit
7f5c3e3a80 (``af_packet: remove BUG statement in
tpacket_destruct_skb'') where this was the case in the TX_RING
side that could be triggered from user space. So really, don't use
BUG() or BUG_ON() unless there's really no way out, and i.e.
don't use it for consistency checking when there's user space
involved, no excuses, especially not if you're slapping the user
with WARN + dump_stack + BUG all at once. The two functions are
of concern:
prb_retire_current_block() [when block status != TP_STATUS_KERNEL]
prb_open_block() [when block_status != TP_STATUS_KERNEL]
Calls to prb_open_block() are guarded by ealier checks if block_status
is really TP_STATUS_KERNEL (racy!), but the first one BUG() is easily
triggable from user space. System behaves still stable after they are
removed. Also remove that yoda condition entirely, since it's already
guarded.
Reported-by: Jakub Zawadzki <darkjames-ws@darkjames.pl>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set correct skb->protocol so that inner packet can
lookup correct gso handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ipv6 traffic, GRE can generate packet with strange GSO
bits, e.g. ipv4 packet with SKB_GSO_TCPV6 flag set. Therefore
following patch relaxes check in inet gso handler to allow
such packet for segmentation.
This patch also fixes wrong skb->protocol set that was done in
gre_gso_segment() handler.
Reported-by: Steinar H. Gunderson <sesse@google.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bridge should only send topology change notice if it is not
the root bridge. It is possible for message age timer to elect itself
as a new root bridge, and still have a topology change timer running
but waiting for bridge lock on other CPU.
Solve the race by checking if we are root bridge before continuing.
This was the root cause of the cases where br_send_tcn_bpdu would OOPS.
Reported-by: JerryKang <jerry.kang@samsung.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg