Don't processes too many packets without allowing other IRQ functions
a chance to run. Otherwise, there is a chance of getting a "soft
lockup" messages and poor application response times.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Up to now, we have set the number of available user contexts based on
the number of hardware contexts which is set according to the number
of available CPUs. This was fine since most CPUs had a power of two
number of cores and the chip supported 4, 8, or 16 user contexts. Now
that some systems have 12 cores, the default isn't optimal and should
be set to 12 even though 16 hardware contexts need to be enabled.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We used to allow only full specification, or using all contexts within
an HCA before moving to the next HCA. We now allow an additional
method -- round-robining through HCAs -- and make that the default.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Turn off IB latency mode. This improves link quality for slower
process chips.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the default llseek action gets changed to no_llseek, all file
systems relying on the current behaviour need to set explicit .llseek
operations.
In case of qib_fs, we want the files to be seekable, so
generic_file_llseek fits best.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than use a variable size array allocation on the stack,
define a constant for the maximum array size possible.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extract the microcode for the QLogic QLE7220 series IB HCA and use the
kernel microcode request facility to load the microcode. This
supports Debian Linux's requirements to separate microcode which
doesn't have open source code available from the device driver.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix world-writable child interface control sysfs attributes
IB/qib: Clean up properly if qib_init() fails
IB/qib: Completion queue callback needs to be single threaded
IB/qib: Update 7322 serdes tables
IB/qib: Clear 6120 hardware error register
IB/qib: Clear eager buffer memory for each new process
IB/qib: Mask hardware error during link reset
IB/qib: Don't mark VL15 bufs as WC to avoid a rare 7322 chip problem
RDMA/cxgb4: Derive smac_idx from port viid
RDMA/cxgb4: Avoid false GTS CIDX_INC overflows
RDMA/cxgb4: Don't call abort_connection() for active connect failures
RDMA/cxgb4: Use the DMA state API instead of the pci equivalents
If qib_init() fails, the driver fails to free memory, unregister
device files, and unregister with the PCIe framework. The driver will
unload without error but a subsequent driver load will cause the
system to panic. This was found by changing the 7220 code to load the
serdes microcode separately and not installing the microcode file.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Workqueues aren't exactly equivalent to tasklets since the callback
function may be called from multiple CPUs before the callback returns.
This causes completion notification callbacks to have MT bugs since
they weren't expecting this behavior. The fix is to use a single
threaded work queue.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hardware error register needs to be cleared or another interrupt
will be generated, thus causing an infinite loop. This is a
regression introduced when removing debug output.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The eager buffers are not being cleared before being mmapped into a
new user address space. This is a potential security risk and should
be fixed. Note that the eager header queue is already being cleared.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HCA checks for certain hardware errors which can be falsely
triggered when the IB link is reset. The fix is to mask them rather
than report them.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't set write combining via PAT on the VL15 buffers to avoid a rare
problem with unaligned writes from interrupt-flushed store buffers.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
get_sb_single() calls fill_super with superblock locked; calling
deactivate_super() will deadlock immedately. Moreover, if fill_super
callback returns an error, get_sb_single() will release the reference
to superblock itself just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The DCA code was left over from internal development to test the
hardware feature and allow performance testing. The results were
mixed and will require some additional work to make full use of the
feature. Therefore, it is being removed for now.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
As part of the earlier patches submitted and reviewed, it was agreed
to change the way serdes tuning parameters were specified to the
driver. The updated patch got dropped by the linux-rdma email list so
the earlier version of qib_iba7322.c ended up being used. This patch
updates qib_iab7322.c to the simpler, single parameter method of
setting the serdes parameters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some of the qib sysfs code passes a buffer pointer into
simple_read_from_buffer() but relies on a function call in another
parameter of the same call to initialize that pointer. Since the order
of evaluation of function parameters is undefined, this will break if
gcc chooses the wrong order.
Fix this by splitting the code into two separate function calls.
This was noticed because of warnings like the following on ppc:
drivers/infiniband/hw/qib/qib_fs.c: In function 'portcntrs_2_read':
drivers/infiniband/hw/qib/qib_fs.c:203: warning: 'counters' is used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a compile error saying qib_init_iba6120_funcs() is
undefined when CONFIG_PCI_MSI is not defined. Thanks to Randy Dunlap
<randy.dunlap@oracle.com> for finding this and suggesting the fix.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a low-level IB driver for QLogic PCIe adapters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ralph Campbell