CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Commit 0b0b0893d4 "of/pci: Fix the conversion of IO ranges into IO
resources" changed the behaviour of of_pci_range_to_resource().
Previously it simply populated the resource based on the arguments. Now
it calls pci_register_io_range() and pci_address_to_pio(). These both
have two implementations depending on whether PCI_IOBASE is defined,
which it is not for powerpc.
Further complicating matters, both routines are weak, and powerpc
implements it's own version of one - pci_address_to_pio(). However
powerpc's implementation depends on other initialisations which are done
later in boot.
The end result is incorrectly initialised IO space. Often we can get
away with that, because we don't make much use of IO space. However
virtio requires it, so we see eg:
pci_bus 0000:00: root bus resource [io 0xffff] (bus address [0xffffffffffffffff-0xffffffffffffffff])
PCI: Cannot allocate resource region 0 of device 0000:00:01.0, will remap
virtio-pci 0000:00:01.0: can't enable device: BAR 0 [io size 0x0020] not assigned
The simplest fix for now is to just stop using of_pci_range_to_resource(),
and open-code the original implementation, that's all we want it to do.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit:
b886576 ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping
introduced some code in user_mem_abort that failed to compile if
STRICT_MM_TYPECHECKS was enabled.
This patch fixes up the failing comparison.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
- enable USB gadget support
- enable Maxim77802 support
- enable Maxim77693 and I2C GPIO drivers
- enable Atmel maXTouch support
- enable SBS battery support
- enable Control Groups support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GSyQ
-----END PGP SIGNATURE-----
Merge tag 'samsung-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung defconfig, actually exynos_defconig updates for v3.18" from
Kukjin Kim:
- enable USB gadget support
- enable Maxim77802 support
- enable Maxim77693 and I2C GPIO drivers
- enable Atmel maXTouch support
- enable SBS battery support
- enable Control Groups support
* tag 'samsung-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Signed-off-by: Olof Johansson <olof@lixom.net>
- fix ifdef around cpu_*_do_[suspend, resume] ops to check
CONFIG_ARM_CPU_SUSPEND and not CONFIG_PM_SLEEP
- fix exynos_defconfig build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
- fix enabling Samsung PM debug functionality due to recently merged
patches and previous merge conflicts
- fix pull-up setting in sd4_width8 pin group for exynos4x12
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6hVm
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v3.18" from Kukjin Kim:
- fix ifdef around cpu_*_do_[suspend, resume] ops to check
CONFIG_ARM_CPU_SUSPEND and not CONFIG_PM_SLEEP
- fix exynos_defconfig build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
- fix enabling Samsung PM debug functionality due to recently merged
patches and previous merge conflicts
- fix pull-up setting in sd4_width8 pin group for exynos4x12
* tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
Signed-off-by: Olof Johansson <olof@lixom.net>
- We need to enable ARM errata 430973 for omap3
- The smc91x on some early n900 boards need to be disabled
for now until the dependencies to specific a bootloader
version are fixed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B9g8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.18-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Two omap fixes for v3.18 merge window" from Tony Lindgren:
Two omap fixes for issues noticed during the merge window:
- We need to enable ARM errata 430973 for omap3
- The smc91x on some early n900 boards need to be disabled
for now until the dependencies to specific a bootloader
version are fixed
* tag 'fixes-for-v3.18-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 97a13e5289 ('net: phy: mdio-sun4i: don't select REGULATOR') removed
the select of REGULATOR, which means that it now has to be explicitly
enabled in the defconfig or things won't work very well.
In particular, this fixes a problem with SD/MMC not probing on my A31-based
board.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
fixes and enhancements to existing drivers as well as new drivers. This
tag contains a bit more arch code than I usually take due to some OMAP2+
changes. Additionally it contains the restart notifier handlers which
are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree I
had to revert one patch and follow up with one more fix near the tip of
this tag. Some dead code is introduced but it will soon become live code
after 3.18-rc1 is released as the rest of the PXA family is converted
over to the common clock framework.
Another trend in this tag is that multiple vendors have started to push
the complexity of changing their CPU frequency into the clock driver,
whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to some
confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=w2rN
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux
Pull clock tree updates from Mike Turquette:
"The clk tree changes for 3.18 are dominated by clock drivers. Mostly
fixes and enhancements to existing drivers as well as new drivers.
This tag contains a bit more arch code than I usually take due to some
OMAP2+ changes. Additionally it contains the restart notifier
handlers which are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree
I had to revert one patch and follow up with one more fix near the tip
of this tag. Some dead code is introduced but it will soon become
live code after 3.18-rc1 is released as the rest of the PXA family is
converted over to the common clock framework.
Another trend in this tag is that multiple vendors have started to
push the complexity of changing their CPU frequency into the clock
driver, whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to
some confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems."
* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
clk: pxa clocks build system fix
Revert "arm: pxa: Transition pxa27x to clk framework"
clk: samsung: register restart handlers for s3c2412 and s3c2443
clk: rockchip: add restart handler
clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
doc/kernel-parameters.txt: clarify clk_ignore_unused
arm: pxa: Transition pxa27x to clk framework
dts: add devicetree bindings for pxa27x clocks
clk: add pxa27x clock drivers
arm: pxa: add clock pll selection bits
clk: dts: document pxa clock binding
clk: add pxa clocks infrastructure
clk: gpio-gate: Ensure gpiod_ APIs are prototyped
clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
clk: ti: LLVMLinux: Move __init outside of type definition
clk: ti: consider the fact that of_clk_get() might return an error
clk: ti: dra7-atl-clock: fix a memory leak
clk: ti: change clock init to use generic of_clk_init
clk: hix5hd2: add I2C clocks
clk: hix5hd2: add watchdog0 clocks
...
The AES loops in arch/sparc/crypto/aes_glue.c use a scheme where the
key material is preloaded into the FPU registers, and then we loop
over and over doing the crypt operation, reusing those pre-cooked key
registers.
There are intervening blkcipher*() calls between the crypt operation
calls. And those might perform memcpy() and thus also try to use the
FPU.
The sparc64 kernel FPU usage mechanism is designed to allow such
recursive uses, but with a catch.
There has to be a trap between the two FPU using threads of control.
The mechanism works by, when the FPU is already in use by the kernel,
allocating a slot for FPU saving at trap time. Then if, within the
trap handler, we try to use the FPU registers, the pre-trap FPU
register state is saved into the slot. Then at trap return time we
notice this and restore the pre-trap FPU state.
Over the long term there are various more involved ways we can make
this work, but for a quick fix let's take advantage of the fact that
the situation where this happens is very limited.
All sparc64 chips that support the crypto instructiosn also are using
the Niagara4 memcpy routine, and that routine only uses the FPU for
large copies where we can't get the source aligned properly to a
multiple of 8 bytes.
We look to see if the FPU is already in use in this context, and if so
we use the non-large copy path which only uses integer registers.
Furthermore, we also limit this special logic to when we are doing
kernel copy, rather than a user copy.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1.
JIT compiler using multi-pass approach to converge to final image size,
since x86 instructions are variable length. It starts with large
gaps between instructions (so some jumps may use imm32 instead of imm8)
and iterates until total program size is the same as in previous pass.
This algorithm works only if program size is strictly decreasing.
Programs that use LD_ABS insn need additional code in prologue, but it
was not emitted during 1st pass, so there was a chance that 2nd pass would
adjust imm32->imm8 jump offsets to the same number of bytes as increase in
prologue, which may cause algorithm to erroneously decide that size converged.
Fix it by always emitting largest prologue in the first pass which
is detected by oldproglen==0 check.
Also change error check condition 'proglen != oldproglen' to fail gracefully.
2.
while staring at the code realized that 64-byte buffer may not be enough
when 1st insn is large, so increase it to 128 to avoid buffer overflow
(theoretical maximum size of prologue+div is 109) and add runtime check.
Fixes: 622582786c ("net: filter: x86: internal BPF JIT")
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Tested-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating or moving a memslot, make sure the IPA space is within the
addressable range of the guest. Otherwise, user space can create too
large a memslot and KVM would try to access potentially unallocated page
table entries when inserting entries in the Stage-2 page tables.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch adds the necessary support for all host kernel PGSIZE and
VA_SPACE configuration options for both EL2 and the Stage-2 page tables.
However, for 40bit and 42bit PARange systems, the architecture mandates
that VTCR_EL2.SL0 is maximum 1, resulting in fewer levels of stage-2
pagge tables than levels of host kernel page tables. At the same time,
systems with a PARange > 42bit, we limit the IPA range by always setting
VTCR_EL2.T0SZ to 24.
To solve the situation with different levels of page tables for Stage-2
translation than the host kernel page tables, we allocate a dummy PGD
with pointers to our actual inital level Stage-2 page table, in order
for us to reuse the kernel pgtable manipulation primitives. Reproducing
all these in KVM does not look pretty and unnecessarily complicates the
32-bit side.
Systems with a PARange < 40bits are not yet supported.
[ I have reworked this patch from its original form submitted by
Jungseok to take the architecture constraints into consideration.
There were too many changes from the original patch for me to
preserve the authorship. Thanks to Catalin Marinas for his help in
figuring out a good solution to this challenge. I have also fixed
various bugs and missing error code handling from the original
patch. - Christoffer ]
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
Pull kbuild changes from Michal Marek:
- fix for handling dependencies of *-objs targets by Masahiro Yamada
- lots of cleanups in the kbuild machinery, also by Masahiro
- fixes for the kconfig build to use an UTF-8 capable ncurses library
if possible and to build on not-so-standard installs
- some more minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Do not reference *-n variables in the Makefile
kbuild: simplify build, clean, modbuiltin shorthands
kbuild: arm: Do not define "comma" twice
kbuild: remove obj-n and lib-n handling
kbuild: remove unnecessary variable initializaions
kbuild: remove unnecessary "obj- := dummy.o" trick
kbuild: handle C=... and M=... after entering into build directory
kbuild: use $(Q) for sub-make target
kbuild: fake the "Entering directory ..." message more simply
kconfig/lxdialog: get ncurses CFLAGS with pkg-config
kconfig: nconfig: fix multi-byte UTF handling
kconfig: lxdialog: fix spelling
kbuild: Make scripts executable
kbuild: remove redundant clean-files from scripts/kconfig/Makefile
kbuild: refactor script/kconfig/Makefile
kbuild: handle the dependency of multi-objs hostprogs appropriately
kbuild: handle multi-objs dependency appropriately
Merge second patch-bomb from Andrew Morton:
- a few hotfixes
- drivers/dma updates
- MAINTAINERS updates
- Quite a lot of lib/ updates
- checkpatch updates
- binfmt updates
- autofs4
- drivers/rtc/
- various small tweaks to less used filesystems
- ipc/ updates
- kernel/watchdog.c changes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm: softdirty: enable write notifications on VMAs after VM_SOFTDIRTY cleared
kernel/param: consolidate __{start,stop}___param[] in <linux/moduleparam.h>
ia64: remove duplicate declarations of __per_cpu_start[] and __per_cpu_end[]
frv: remove unused declarations of __start___ex_table and __stop___ex_table
kvm: ensure hard lockup detection is disabled by default
kernel/watchdog.c: control hard lockup detection default
staging: rtl8192u: use %*pEn to escape buffer
staging: rtl8192e: use %*pEn to escape buffer
staging: wlan-ng: use %*pEhp to print SN
lib80211: remove unused print_ssid()
wireless: hostap: proc: print properly escaped SSID
wireless: ipw2x00: print SSID via %*pE
wireless: libertas: print esaped string via %*pE
lib/vsprintf: add %*pE[achnops] format specifier
lib / string_helpers: introduce string_escape_mem()
lib / string_helpers: refactoring the test suite
lib / string_helpers: move documentation to c-file
include/linux: remove strict_strto* definitions
arch/x86/mm/numa.c: fix boot failure when all nodes are hotpluggable
fs: check bh blocknr earlier when searching lru
...
Pull m68knommu update from Greg Ungerer:
"The major change is to remove the arch/m68k/platform directory. The
coldfire (and other non-mmu m68k platform) code is moved to the
arch/m68k level, making them consistent with the traditional m68k
platforms.
A couple of other minor miscellaneous fixes as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: Fix typo 'COFNIG_MBAR'
m68knommu: add missing ioport_map() and ioport_unmap()
m68k/coldfire: remove second asm/mcfclk.h inclusion in m54xx.c
m68knommu: fix size of address field for 5272 interrupt controller
m68k: fix crufty 68000 and 68360 intro comments
m68k: remove the unused arch/m68k/platform directory
m68k: move non-mmu 68360 platform code
m68k: move non-mmu 68000 platform code
m68k: fix crufty ColdFire intro comments
m68k: move coldfire platform code
Pull UML update from Richard Weinberger:
"Besides of fixes this contains also support for CONFIG_STACKTRACE by
Daniel Walter"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: net: Eliminate NULL test after alloc_bootmem
um: Add support for CONFIG_STACKTRACE
um: ubd: Fix for processes stuck in D state forever
um: delete unnecessary bootmem struct page array
um: remove csum_partial_copy_generic_i386 to clean up exception table
Pull s390 updates from Martin Schwidefsky:
"This patch set contains the main portion of the changes for 3.18 in
regard to the s390 architecture. It is a bit bigger than usual,
mainly because of a new driver and the vector extension patches.
The interesting bits are:
- Quite a bit of work on the tracing front. Uprobes is enabled and
the ftrace code is reworked to get some of the lost performance
back if CONFIG_FTRACE is enabled.
- To improve boot time with CONFIG_DEBIG_PAGEALLOC, support for the
IPTE range facility is added.
- The rwlock code is re-factored to improve writer fairness and to be
able to use the interlocked-access instructions.
- The kernel part for the support of the vector extension is added.
- The device driver to access the CD/DVD on the HMC is added, this
will hopefully come in handy to improve the installation process.
- Add support for control-unit initiated reconfiguration.
- The crypto device driver is enhanced to enable the additional AP
domains and to allow the new crypto hardware to be used.
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/ftrace: simplify enabling/disabling of ftrace_graph_caller
s390/ftrace: remove 31 bit ftrace support
s390/kdump: add support for vector extension
s390/disassembler: add vector instructions
s390: add support for vector extension
s390/zcrypt: Toleration of new crypto hardware
s390/idle: consolidate idle functions and definitions
s390/nohz: use a per-cpu flag for arch_needs_cpu
s390/vtime: do not reset idle data on CPU hotplug
s390/dasd: add support for control unit initiated reconfiguration
s390/dasd: fix infinite loop during format
s390/mm: make use of ipte range facility
s390/setup: correct 4-level kernel page table detection
s390/topology: call set_sched_topology early
s390/uprobes: architecture backend for uprobes
s390/uprobes: common library for kprobes and uprobes
s390/rwlock: use the interlocked-access facility 1 instructions
s390/rwlock: improve writer fairness
s390/rwlock: remove interrupt-enabling rwlock variant.
s390/mm: remove change bit override support
...
Pull x86 ras, uv and vdso fixlets from Ingo Molnar:
"ras: tone down a kernel message to only occur during initial bootup,
not during suspend/resume cycles.
uv: a cleanup commit
vdso: a fix to error checking"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Avoid showing repetitive message from intel_init_thermal()
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/uv: Remove unnecessary #ifdef
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Fix vdso2c's special_pages[] error checking
Pull x86 fixes from Ingo Molnar:
"Misc smaller fixes that missed the v3.17 cycle"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/build: Add arch/x86/purgatory/ make generated files to gitignore
x86: Fix section conflict for numachip
x86: Reject x32 executables if x32 ABI not supported
x86_64, entry: Filter RFLAGS.NT on entry from userspace
x86, boot, kaslr: Fix nuisance warning on 32-bit builds
Pull x86 seccomp changes from Ingo Molnar:
"This tree includes x86 seccomp filter speedups and related preparatory
work, which touches core seccomp facilities as well.
The main idea is to split seccomp into two phases, to be able to enter
a simple fast path for syscalls with ptrace side effects.
There's no substantial user-visible (and ABI) effects expected from
this, except a change in how we emit a better audit record for
SECCOMP_RET_TRACE events"
* 'x86-seccomp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64, entry: Use split-phase syscall_trace_enter for 64-bit syscalls
x86_64, entry: Treat regs->ax the same in fastpath and slowpath syscalls
x86: Split syscall_trace_enter into two phases
x86, entry: Only call user_exit if TIF_NOHZ
x86, x32, audit: Fix x32's AUDIT_ARCH wrt audit
seccomp: Document two-phase seccomp and arch-provided seccomp_data
seccomp: Allow arch code to provide seccomp_data
seccomp: Refactor the filter callback and the API
seccomp,x86,arm,mips,s390: Remove nr parameter from secure_computing
Pull x86 platform updates from Ingo Molnar:
"The main changes in this tree are:
- fix and update Intel Quark [Galileo] SoC platform support
- update IOSF chipset side band interface and make it available via
debugfs
- enable HPETs on Soekris net6501 and other e6xx based systems"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Add cpu_detect_cache_sizes to init_intel() add Quark legacy_cache()
x86: Quark: Comment setup_arch() to document TLB/PGE bug
x86/intel/quark: Switch off CR4.PGE so TLB flush uses CR3 instead
x86/platform/intel/iosf: Add debugfs config option for IOSF
x86/platform/intel/iosf: Add better description of IOSF driver in config
x86/platform/intel/iosf: Add Braswell PCI ID
x86/platform/pmc_atom: Fix warning when CONFIG_DEBUG_FS=n
x86: HPET force enable for e6xx based systems
x86/iosf: Add debugfs support
x86/iosf: Add Kconfig prompt for IOSF_MBI selection
Pull x86 mm updates from Ingo Molnar:
"This tree includes the following changes:
- fix memory hotplug
- fix hibernation bootup memory layout assumptions
- fix hyperv numa guest kernel messages
- remove dead code
- update documentation"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Update memory map description to list hypervisor-reserved area
x86/mm, hibernate: Do not assume the first e820 area to be RAM
x86/mm/numa: Drop dead code and rename setup_node_data() to setup_alloc_data()
x86/mm/hotplug: Modify PGD entry when removing memory
x86/mm/hotplug: Pass sync_global_pgds() a correct argument in remove_pagetable()
x86: Remove set_pmd_pfn
Pull x86 FPU updates from Ingo Molnar:
"x86 FPU handling fixes, cleanups and enhancements from Oleg.
The signal handling race fix and the __restore_xstate_sig() preemption
fix for eager-mode is marked for -stable as well"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: copy_thread: Don't nullify ->ptrace_bps twice
x86, fpu: Shift "fpu_counter = 0" from copy_thread() to arch_dup_task_struct()
x86, fpu: copy_process: Sanitize fpu->last_cpu initialization
x86, fpu: copy_process: Avoid fpu_alloc/copy if !used_math()
x86, fpu: Change __thread_fpu_begin() to use use_eager_fpu()
x86, fpu: __restore_xstate_sig()->math_state_restore() needs preempt_disable()
x86, fpu: shift drop_init_fpu() from save_xstate_sig() to handle_signal()
Pull x86 cpufeature updates from Ingo Molnar:
"This tree includes the following changes:
- Introduce DISABLED_MASK to list disabled CPU features, to simplify
CPU feature handling and avoid excessive #ifdefs
- Remove the lightly used cpu_has_pae() primitive"
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Add more disabled features
x86: Introduce disabled-features
x86: Axe the lightly-used cpu_has_pae
Use watchdog_enable_hardlockup_detector() to set hard lockup detection's
default value to false. It's risky to run this detection in a guest, as
false positives are easy to trigger, especially if the host is
overcommitted.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If all the nodes are marked hotpluggable, alloc node data will fail.
Because __next_mem_range_rev() will skip the hotpluggable memory
regions. numa_clear_kernel_node_hotplug() is called after alloc node
data.
numa_init()
...
ret = init_func(); // this will mark hotpluggable flag from SRAT
...
memblock_set_bottom_up(false);
...
ret = numa_register_memblks(&numa_meminfo); // this will alloc node data(pglist_data)
...
numa_clear_kernel_node_hotplug(); // in case all the nodes are hotpluggable
...
numa_register_memblks()
setup_node_data()
memblock_find_in_range_node()
__memblock_find_range_top_down()
for_each_mem_range_rev()
__next_mem_range_rev()
This patch moves numa_clear_kernel_node_hotplug() into
numa_register_memblks(), clear kernel node hotpluggable flag before
alloc node data, then alloc node data won't fail even all the nodes
are hotpluggable.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86_64 allnoconfig:
arch/x86/kernel/cpu/common.c:968: warning: 'syscall32_cpu_init' defined but not used
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the optimized ioresource lookup, "region_is_ram", for the ioremap
function. If the region is not found, it falls back to the
"page_is_ram" function. If it is found and it is RAM, then the usual
warning message is issued, and the ioremap operation is aborted.
Otherwise, the ioremap operation continues.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Alex Thorlton <athorlton@sgi.com>
Reviewed-by: Cliff Wickman <cpw@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells brought to my attention the mails generated by kbuild test
bot and following sparse warnings were present. This patch fixes these
warnings.
arch/x86/kernel/kexec-bzimage64.c:270:5: warning: symbol 'bzImage64_probe' was not declared. Should it be static?
arch/x86/kernel/kexec-bzimage64.c:328:6: warning: symbol 'bzImage64_load' was not declared. Should it be static?
arch/x86/kernel/kexec-bzimage64.c:517:5: warning: symbol 'bzImage64_cleanup' was not declared. Should it be static?
arch/x86/kernel/kexec-bzimage64.c:531:5: warning: symbol 'bzImage64_verify_sig' was not declared. Should it be static?
arch/x86/kernel/kexec-bzimage64.c:546:23: warning: symbol 'kexec_bzImage64_ops' was not declared. Should it be static?
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Reported-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a check if crashk_res_low exists just like GART region does. If
crashk_res_low doesn't exist, calling exclude_mem_range is unnecessary.
Meanwhile, since crashk_res_low has been initialized at definition, it's
safe just use "if (crashk_low_res.end)" to check if it's exist. And this
can make it consistent with other places of check.
Signed-off-by: Baoquan He <bhe@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the Makefile of kexec purgatory be consistent with others in linux
src tree, and make it look generic and simple.
Signed-off-by: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alloc_bootmem and related functions never return NULL. Thus a NULL
test or memset after calls to these functions is unnecessary.
The following Coccinelle semantic patch was used for making the change:
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- if (E == NULL) S
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
Starting with Linux 3.12 processes get stuck in D state forever in
UserModeLinux under sync heavy workloads. This bug was introduced by
commit 805f11a0d5 (um: ubd: Add REQ_FLUSH suppport).
Fix bug by adding a check if FLUSH request was successfully submitted to
the I/O thread and keeping the FLUSH request on the request queue on
submission failures.
Fixes: 805f11a0d5 (um: ubd: Add REQ_FLUSH suppport)
Signed-off-by: Thorsten Knabe <linux@thorsten-knabe.de>
Cc: stable@kernel.org # >= 3.12
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull x86 cpu offlining patch from Ingo Molnar:
"This tree includes a single commit that speeds up x86 suspend/resume
by replacing a naive 100msec sleep based polling loop with proper
completion notification.
This gives some real suspend/resume benefit on servers with larger
core counts"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smpboot: Speed up suspend/resume by avoiding 100ms sleep for CPU offline during S3
Pull x86 cleanups from Ingo Molnar:
"Three small cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tty/serial/8250: Clean up the asm/serial.h include file a bit
x86/tty/serial/8250: Resolve missing-field-initializers warnings
x86: Remove obsolete comment in uapi/e820.h
Pull x86 build update from Ingo Molnar:
"A single commit that simplifies the no-FPU-ops build options"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kbuild: Eliminate duplicate command line options
Pull x86 bootup updates from Ingo Molnar:
"The changes in this cycle were:
- Fix rare SMP-boot hang (mostly in virtual environments)
- Fix build warning with certain (rare) toolchains"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/relocs: Make per_cpu_load_addr static
x86/smpboot: Initialize secondary CPU only if master CPU will wait for it
Pull x86 asm updates from Ingo Molnar:
"The changes in this cycle were:
- Speed up the x86 __preempt_schedule() implementation
- Fix/improve low level asm code debug info annotations"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Unwind-annotate thunk_32.S
x86: Improve cmpxchg8b_emu.S
x86: Improve cmpxchg16b_emu.S
x86/lib/Makefile: Remove the unnecessary "+= thunk_64.o"
x86: Speed up ___preempt_schedule*() by using THUNK helpers
1) uml kernel bootmem managed through bootmem_data->node_bootmem_map,
not the struct page array, so the array is unnecessary.
2) the bootmem struct page array has been pointed by a *local* pointer,
struct page *map, in init_maps function. The array can be accessed only
in init_maps's scope. As a result, uml kernel wastes about 1% of total
memory.
Signed-off-by: Honggang Li <enjoymindful@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
arch/x86/um/checksum_32.S had been copy & paste from x86. When build
x86 uml, csum_partial_copy_generic_i386 mess up the exception table.
In fact, exception table dose not work in uml kernel.
And csum_partial_copy_generic_i386 never been called. So, delete it.
Signed-off-by: Honggang Li <enjoymindful@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Optimized support for Intel "Cluster-on-Die" (CoD) topologies (Dave
Hansen)
- Various sched/idle refinements for better idle handling (Nicolas
Pitre, Daniel Lezcano, Chuansheng Liu, Vincent Guittot)
- sched/numa updates and optimizations (Rik van Riel)
- sysbench speedup (Vincent Guittot)
- capacity calculation cleanups/refactoring (Vincent Guittot)
- Various cleanups to thread group iteration (Oleg Nesterov)
- Double-rq-lock removal optimization and various refactorings
(Kirill Tkhai)
- various sched/deadline fixes
... and lots of other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/dl: Use dl_bw_of() under rcu_read_lock_sched()
sched/fair: Delete resched_cpu() from idle_balance()
sched, time: Fix build error with 64 bit cputime_t on 32 bit systems
sched: Improve sysbench performance by fixing spurious active migration
sched/x86: Fix up typo in topology detection
x86, sched: Add new topology for multi-NUMA-node CPUs
sched/rt: Use resched_curr() in task_tick_rt()
sched: Use rq->rd in sched_setaffinity() under RCU read lock
sched: cleanup: Rename 'out_unlock' to 'out_free_new_mask'
sched: Use dl_bw_of() under RCU read lock
sched/fair: Remove duplicate code from can_migrate_task()
sched, mips, ia64: Remove __ARCH_WANT_UNLOCKED_CTXSW
sched: print_rq(): Don't use tasklist_lock
sched: normalize_rt_tasks(): Don't use _irqsave for tasklist_lock, use task_rq_lock()
sched: Fix the task-group check in tg_has_rt_tasks()
sched/fair: Leverage the idle state info when choosing the "idlest" cpu
sched: Let the scheduler see CPU idle states
sched/deadline: Fix inter- exclusive cpusets migrations
sched/deadline: Clear dl_entity params when setscheduling to different class
sched/numa: Kill the wrong/dead TASK_DEAD check in task_numa_fault()
...
Pull perf updates from Ingo Molnar:
"Kernel side updates:
- Fix and enhance poll support (Jiri Olsa)
- Re-enable inheritance optimization (Jiri Olsa)
- Enhance Intel memory events support (Stephane Eranian)
- Refactor the Intel uncore driver to be more maintainable (Zheng
Yan)
- Enhance and fix Intel CPU and uncore PMU drivers (Peter Zijlstra,
Andi Kleen)
- [ plus various smaller fixes/cleanups ]
User visible tooling updates:
- Add +field argument support for --field option, so that one can add
fields to the default list of fields to show, ie now one can just
do:
perf report --fields +pid
And the pid will appear in addition to the default fields (Jiri
Olsa)
- Add +field argument support for --sort option (Jiri Olsa)
- Honour -w in the report tools (report, top), allowing to specify
the widths for the histogram entries columns (Namhyung Kim)
- Properly show submicrosecond times in 'perf kvm stat' (Christian
Borntraeger)
- Add beautifier for mremap flags param in 'trace' (Alex Snast)
- perf script: Allow callchains if any event samples them
- Don't truncate Intel style addresses in 'annotate' (Alex Converse)
- Allow profiling when kptr_restrict == 1 for non root users, kernel
samples will just remain unresolved (Andi Kleen)
- Allow configuring default options for callchains in config file
(Namhyung Kim)
- Support operations for shared futexes. (Davidlohr Bueso)
- "perf kvm stat report" improvements by Alexander Yarygin:
- Save pid string in opts.target.pid
- Enable the target.system_wide flag
- Unify the title bar output
- [ plus lots of other fixes and small improvements. ]
Tooling infrastructure changes:
- Refactor unit and scale function parameters for PMU parsing
routines (Matt Fleming)
- Improve DSO long names lookup with rbtree, resulting in great
speedup for workloads with lots of DSOs (Waiman Long)
- We were not handling POLLHUP notifications for event file
descriptors
Fix it by filtering entries in the events file descriptor array
after poll() returns, refcounting mmaps so that when the last fd
pointing to a perf mmap goes away we do the unmap (Arnaldo Carvalho
de Melo)
- Intel PT prep work, from Adrian Hunter, including:
- Let a user specify a PMU event without any config terms
- Add perf-with-kcore script
- Let default config be defined for a PMU
- Add perf_pmu__scan_file()
- Add a 'perf test' for tracking with sched_switch
- Add 'flush' callback to scripting API
- Use ring buffer consume method to look like other tools (Arnaldo
Carvalho de Melo)
- hists browser (used in top and report) refactorings, getting rid of
unused variables and reducing source code size by handling similar
cases in a fewer functions (Namhyung Kim).
- Replace thread unsafe strerror() with strerror_r() accross the
whole tools/perf/ tree (Masami Hiramatsu)
- Rename ordered_samples to ordered_events and allow setting a queue
size for ordering events (Jiri Olsa)
- [ plus lots of fixes, cleanups and other improvements ]"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (198 commits)
perf/x86: Tone down kernel messages when the PMU check fails in a virtual environment
perf/x86/intel/uncore: Fix minor race in box set up
perf record: Fix error message for --filter option not coming after tracepoint
perf tools: Fix build breakage on arm64 targets
perf symbols: Improve DSO long names lookup speed with rbtree
perf symbols: Encapsulate dsos list head into struct dsos
perf bench futex: Sanitize -q option in requeue
perf bench futex: Support operations for shared futexes
perf trace: Fix mmap return address truncation to 32-bit
perf tools: Refactor unit and scale function parameters
perf tools: Fix line number in the config file error message
perf tools: Convert {record,top}.call-graph option to call-graph.record-mode
perf tools: Introduce perf_callchain_config()
perf callchain: Move some parser functions to callchain.c
perf tools: Move callchain config from record_opts to callchain_param
perf hists browser: Fix callchain print bug on TUI
perf tools: Use ACCESS_ONCE() instead of volatile cast
perf tools: Modify error code for when perf_session__new() fails
perf tools: Fix perf record as non root with kptr_restrict == 1
perf stat: Fix --per-core on multi socket systems
...
Pull core locking updates from Ingo Molnar:
"The main updates in this cycle were:
- mutex MCS refactoring finishing touches: improve comments, refactor
and clean up code, reduce debug data structure footprint, etc.
- qrwlock finishing touches: remove old code, self-test updates.
- small rwsem optimization
- various smaller fixes/cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Revert qrwlock recusive stuff
locking/rwsem: Avoid double checking before try acquiring write lock
locking/rwsem: Move EXPORT_SYMBOL() lines to follow function definition
locking/rwlock, x86: Delete unused asm/rwlock.h and rwlock.S
locking/rwlock, x86: Clean up asm/spinlock*.h to remove old rwlock code
locking/semaphore: Resolve some shadow warnings
locking/selftest: Support queued rwlock
locking/lockdep: Restrict the use of recursive read_lock() with qrwlock
locking/spinlocks: Always evaluate the second argument of spin_lock_nested()
locking/Documentation: Update locking/mutex-design.txt disadvantages
locking/Documentation: Move locking related docs into Documentation/locking/
locking/mutexes: Use MUTEX_SPIN_ON_OWNER when appropriate
locking/mutexes: Refactor optimistic spinning code
locking/mcs: Remove obsolete comment
locking/mutexes: Document quick lock release when unlocking
locking/mutexes: Standardize arguments in lock/unlock slowpaths
locking: Remove deprecated smp_mb__() barriers
Pull arch atomic cleanups from Ingo Molnar:
"This is a series kept separate from the main locking tree, which
cleans up and improves various details in the atomics type handling:
- Remove the unused atomic_or_long() method
- Consolidate and compress atomic ops implementations between
architectures, to reduce linecount and to make it easier to add new
ops.
- Rewrite generic atomic support to only require cmpxchg() from an
architecture - generate all other methods from that"
* 'locking-arch-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
locking,arch: Use ACCESS_ONCE() instead of cast to volatile in atomic_read()
locking, mips: Fix atomics
locking, sparc64: Fix atomics
locking,arch: Rewrite generic atomic support
locking,arch,xtensa: Fold atomic_ops
locking,arch,sparc: Fold atomic_ops
locking,arch,sh: Fold atomic_ops
locking,arch,powerpc: Fold atomic_ops
locking,arch,parisc: Fold atomic_ops
locking,arch,mn10300: Fold atomic_ops
locking,arch,mips: Fold atomic_ops
locking,arch,metag: Fold atomic_ops
locking,arch,m68k: Fold atomic_ops
locking,arch,m32r: Fold atomic_ops
locking,arch,ia64: Fold atomic_ops
locking,arch,hexagon: Fold atomic_ops
locking,arch,cris: Fold atomic_ops
locking,arch,avr32: Fold atomic_ops
locking,arch,arm64: Fold atomic_ops
locking,arch,arm: Fold atomic_ops
...
There is really no point in faulting in memory regions page by page
if they are not backed by demand paged system RAM but by a linear
passthrough mapping of a host MMIO region. So instead, detect such
regions at setup time and install the mappings for the backing all
at once.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
This patch reduces the value of SIGRTMIN on PARISC from 37 to 32, thus
increasing the number of available RT signals and bring it in sync with other
Linux architectures.
Historically we wanted to natively support HP-UX 32bit binaries with the
PA-RISC Linux port. Because of that we carried the various available signals
from HP-UX (e.g. SIGEMT and SIGLOST) and folded them in between the native
Linux signals. Although this was the right decision at that time, this
required us to increase SIGRTMIN to at least 37 which left us with 27 (64-37)
RT signals.
Those 27 RT signals haven't been a problem in the past, but with the upcoming
importance of systemd we now got the problem that systemd alloctes (hardcoded)
signals up to SIGRTMIN+29 which is beyond our NSIG of 64. Because of that we
have not been able to use systemd on the PARISC Linux port yet.
Of course we could ask the systemd developers to not use those hardcoded
values, but this change is very unlikely, esp. with PA-RISC being a niche
architecture.
The other possibility would be to increase NSIG to e.g. 128, but this would
mean to duplicate most of the existing Linux signal handling code into the
parisc specific Linux kernel tree which would most likely introduce lots of new
bugs beside the code duplication.
The third option is to drop some HP-UX signals and shuffle some other signals
around to bring SIGRTMIN to 32. This is of course an ABI change, but testing
has shown that existing Linux installations are not visibly affected by this
change - most likely because we move those signals around which are rarely used
and move them to slots which haven't been used in Linux yet. In an existing
installation I was able to exchange either the Linux kernel or glibc (or both)
without affecting the boot process and installed applications.
Dropping the HP-UX signals isn't an issue either, since support for HP-UX was
basically dropped a few months back with Kernel 3.14 in commit
f5a408d53e already, when we changed EWOULDBLOCK
to be equal to EAGAIN.
So, even if this is an ABI change, it's better to change it now and thus bring
PARISC Linux in sync with other architectures to avoid other issues in the
future.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Carlos O'Donell <carlos@systemhalted.org>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: PARISC Linux Kernel Mailinglist <linux-parisc@vger.kernel.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Pull networking fixes from David Miller:
"This set fixes a bunch of fallout from the changes that went in during
this merge window, particularly:
- Fix fsl_pq_mdio (Claudiu Manoil) and fm10k (Pranith Kumar) build
failures.
- Several networking drivers do atomic_set() on page counts where
that's not exactly legal. From Eric Dumazet.
- Make __skb_flow_get_ports() work cleanly with unaligned data, from
Alexander Duyck.
- Fix some kernel-doc buglets in rfkill and netlabel, from Fabian
Frederick.
- Unbalanced enable_irq_wake usage in bcmgenet and systemport
drivers, from Florian Fainelli.
- pxa168_eth needs to depend on HAS_DMA, from Geert Uytterhoeven.
- Multi-dequeue in the qdisc layer severely bypasses the fairness
limits the previous code used to enforce, reintroduce in a way that
at the same time doesn't compromise bulk dequeue opportunities.
From Jesper Dangaard Brouer.
- macvlan receive path unnecessarily hops through a softirq by using
netif_rx() instead of netif_receive_skb(). From Jason Baron"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (51 commits)
net: systemport: avoid unbalanced enable_irq_wake calls
net: bcmgenet: avoid unbalanced enable_irq_wake calls
net: bcmgenet: fix off-by-one in incrementing read pointer
net: fix races in page->_count manipulation
mlx4: fix race accessing page->_count
ixgbe: fix race accessing page->_count
igb: fix race accessing page->_count
fm10k: fix race accessing page->_count
net/phy: micrel: Add clock support for KSZ8021/KSZ8031
flow-dissector: Fix alignment issue in __skb_flow_get_ports
net: filter: fix the comments
Documentation: replace __sk_run_filter with __bpf_prog_run
macvlan: optimize the receive path
macvlan: pass 'bool' type to macvlan_count_rx()
drivers: net: xgene: Add 10GbE ethtool support
drivers: net: xgene: Add 10GbE support
drivers: net: xgene: Preparing for adding 10GbE support
dtb: Add 10GbE node to APM X-Gene SoC device tree
Documentation: dts: Update section header for APM X-Gene
MAINTAINERS: Update APM X-Gene section
...
Pull sparc updates from David Miller:
1) Move to 4-level page tables on sparc64 and support up to 53-bits of
physical addressing. Kernel static image BSS size reduced by
several megabytes.
2) M6/M7 cpu support, from Allan Pais.
3) Move to sparse IRQs, handle hypervisor TLB call errors more
gracefully, and add T5 perf_event support. From Bob Picco.
4) Recognize cdroms and compute geometry from capacity in virtual disk
driver, also from Allan Pais.
5) Fix memset() return value on sparc32, from Andreas Larsson.
6) Respect gfp flags in dma_alloc_coherent on sparc32, from Daniel
Hellstrom.
7) Fix handling of compound pages in virtual disk driver, from Dwight
Engen.
8) Fix lockdep warnings in LDC layer by moving IRQ requesting to
ldc_alloc() from ldc_bind().
9) Increase boot string length to 1024 bytes, from Dave Kleikamp.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: (31 commits)
sparc64: Fix lockdep warnings on reboot on Ultra-5
sparc64: Increase size of boot string to 1024 bytes
sparc64: Kill unnecessary tables and increase MAX_BANKS.
sparc64: sparse irq
sparc64: Adjust vmalloc region size based upon available virtual address bits.
sparc64: Increase MAX_PHYS_ADDRESS_BITS to 53.
sparc64: Use kernel page tables for vmemmap.
sparc64: Fix physical memory management regressions with large max_phys_bits.
sparc64: Adjust KTSB assembler to support larger physical addresses.
sparc64: Define VA hole at run time, rather than at compile time.
sparc64: Switch to 4-level page tables.
sparc64: Fix reversed start/end in flush_tlb_kernel_range()
sparc64: Add vio_set_intr() to enable/disable Rx interrupts
vio: fix reuse of vio_dring slot
sunvdc: limit each sg segment to a page
sunvdc: compute vdisk geometry from capacity
sunvdc: add cdrom and v1.1 protocol support
sparc: VIO protocol version 1.6
sparc64: Fix hibernation code refrence to PAGE_OFFSET.
sparc64: Move request_irq() from ldc_bind() to ldc_alloc()
...
Pull powerpc updates from Michael Ellerman:
"Here's a first pull request for powerpc updates for 3.18.
The bulk of the additions are for the "cxl" driver, for IBM's Coherent
Accelerator Processor Interface (CAPI). Most of it's in drivers/misc,
which Greg & Arnd maintain, Greg said he was happy for us to take it
through our tree.
There's the usual minor cleanups and fixes, including a bit of noise
in drivers from some of those. A bunch of updates to our EEH code,
which has been getting more testing. Several nice speedups from
Anton, including 20% in clear_page().
And a bunch of updates for freescale from Scott"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (130 commits)
cxl: Fix afu_read() not doing finish_wait() on signal or non-blocking
cxl: Add documentation for userspace APIs
cxl: Add driver to Kbuild and Makefiles
cxl: Add userspace header file
cxl: Driver code for powernv PCIe based cards for userspace access
cxl: Add base builtin support
powerpc/mm: Add hooks for cxl
powerpc/opal: Add PHB to cxl mode call
powerpc/mm: Add new hash_page_mm()
powerpc/powerpc: Add new PCIe functions for allocating cxl interrupts
cxl: Add new header for call backs and structs
powerpc/powernv: Split out set MSI IRQ chip code
powerpc/mm: Export mmu_kernel_ssize and mmu_linear_psize
powerpc/msi: Improve IRQ bitmap allocator
powerpc/cell: Make spu_flush_all_slbs() generic
powerpc/cell: Move data segment faulting code out of cell platform
powerpc/cell: Move spu_handle_mm_fault() out of cell platform
powerpc/pseries: Use new defines when calling H_SET_MODE
powerpc: Update contact info in Documentation files
powerpc/perf/hv-24x7: Simplify catalog_read()
...
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
- Fix SDIO IRQ bug.
- MMC regulator improvements.
- Fix slot-gpio card detect bug.
- Add support for Driver Stage Register.
- Convert the common MMC OF parser to use GPIO descriptors.
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk().
- Some additional minor fixes.
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA.
- dw_mmc: Use common MMC regulators.
- dw_mmc: Add support for Rock-chips RK3288.
- tmio: Enable runtime PM support.
- tmio: Add support for R-Car Gen2 SoCs.
- tmio: Several fixes and improvements.
- omap_hsmmc: Removed Balaji from MAINTAINERS.
- jz4740: add DMA and pre/post support.
- sdhci: Add support for Intel Braswell.
- sdhci: Several fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VFRY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix SDIO IRQ bug
- MMC regulator improvements
- Fix slot-gpio card detect bug
- Add support for Driver Stage Register
- Convert the common MMC OF parser to use GPIO descriptors
- Convert MMC_CAP2_NO_MULTI_READ into a callback, ->multi_io_quirk()
- Some additional minor fixes
MMC host:
- mmci: Support Qualcomm specific DML layer for DMA
- dw_mmc: Use common MMC regulators
- dw_mmc: Add support for Rock-chips RK3288
- tmio: Enable runtime PM support
- tmio: Add support for R-Car Gen2 SoCs
- tmio: Several fixes and improvements
- omap_hsmmc: Removed Balaji from MAINTAINERS
- jz4740: add DMA and pre/post support
- sdhci: Add support for Intel Braswell
- sdhci: Several fixes and improvements"
* tag 'mmc-v3.18-1' of git://git.linaro.org/people/ulf.hansson/mmc: (119 commits)
ARM: dts: fix MMC2 regulators for Exynos5420 Arndale Octa board
mmc: sdhci-acpi: Fix Braswell eMMC timeout clock frequency
mmc: sdhci-acpi: Pass HID and UID to probe_slot
mmc: sdhci-acpi: Get UID directly from acpi_device
mmc, sdhci, bcm-kona, LLVMLinux: Remove use of __initconst
mmc: sdhci-pci: Fix Braswell eMMC timeout clock frequency
mmc: sdhci: Let a driver override timeout clock frequency
mmc: sdhci-pci: Add Bay Trail and Braswell SD card detect
mmc: sdhci-pci: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers
mmc: sdhci-acpi: Add a HID and UID for a SD Card host controller
mmc: sdhci-acpi: Set SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers
mmc: sdhci: Add quirk for always getting TC with stop cmd
mmc: core: restore detect line inversion semantics
mmc: Fix incorrect warning when setting 0 Hz via debugfs
mmc: Fix use of wrong device in mmc_gpiod_free_cd()
mmc: atmel-mci: fix mismatched section on atmci_cleanup_slot
mmc: rtsx_pci: Set power related cap2 macros
mmc: core: Add new power_mode MMC_POWER_UNDEFINED
mmc: sdhci: execute tuning when device is not busy
mmc: atmel-mci: Release mmc resources on failure in probe
..
Pull dma-mapping update from Marek Szyprowski:
"Provide the dma write coherent api (available previously on ARM
architecture) for all other architectures, which use dma_ops-based dma
mapping implementation.
This lets one to use the same code in the device drivers regardless of
the selected architecture"
* 'for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
dma-mapping: Provide write-combine allocations
s390: Implement dma_{alloc,free}_attrs()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cP1w
-----END PGP SIGNATURE-----
Merge tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull restart handler infrastructure from Guenter Roeck:
"This series was supposed to be pulled through various trees using it,
and I did not plan to send a separate pull request. As it turns out,
the pinctrl tree did not merge with it, is now upstream, and uses it,
meaning there are now build failures.
Please pull this series directly to fix those build failures"
* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
arm/arm64: unexport restart handlers
watchdog: sunxi: register restart handler with kernel restart handler
watchdog: alim7101: register restart handler with kernel restart handler
watchdog: moxart: register restart handler with kernel restart handler
arm: support restart through restart handler call chain
arm64: support restart through restart handler call chain
power/restart: call machine_restart instead of arm_pm_restart
kernel: add support for kernel restart handler call chain
Inconsistently, the raw_* IRQ routines do not interact with and update
the irqflags tracing and lockdep state, whereas the raw_* spinlock
interfaces do.
This causes problems in p1275_cmd_direct() because we disable hardirqs
by hand using raw_local_irq_restore() and then do a raw_spin_lock()
which triggers a lockdep trace because the CPU's hw IRQ state doesn't
match IRQ tracing's internal software copy of that state.
The CPU's irqs are disabled, yet current->hardirqs_enabled is true.
====================
reboot: Restarting system
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:3536 check_flags+0x7c/0x240()
DEBUG_LOCKS_WARN_ON(current->hardirqs_enabled)
Modules linked in: openpromfs
CPU: 0 PID: 1 Comm: systemd-shutdow Tainted: G W 3.17.0-dirty #145
Call Trace:
[000000000045919c] warn_slowpath_common+0x5c/0xa0
[0000000000459210] warn_slowpath_fmt+0x30/0x40
[000000000048f41c] check_flags+0x7c/0x240
[0000000000493280] lock_acquire+0x20/0x1c0
[0000000000832b70] _raw_spin_lock+0x30/0x60
[000000000068f2fc] p1275_cmd_direct+0x1c/0x60
[000000000068ed28] prom_reboot+0x28/0x40
[000000000043610c] machine_restart+0x4c/0x80
[000000000047d2d4] kernel_restart+0x54/0x80
[000000000047d618] SyS_reboot+0x138/0x200
[00000000004060b4] linux_sparc_syscall32+0x34/0x60
---[ end trace 5c439fe81c05a100 ]---
possible reason: unannotated irqs-off.
irq event stamp: 2010267
hardirqs last enabled at (2010267): [<000000000049a358>] vprintk_emit+0x4b8/0x580
hardirqs last disabled at (2010266): [<0000000000499f08>] vprintk_emit+0x68/0x580
softirqs last enabled at (2010046): [<000000000045d278>] __do_softirq+0x378/0x4a0
softirqs last disabled at (2010039): [<000000000042bf08>] do_softirq_own_stack+0x28/0x40
Resetting ...
====================
Use local_* variables of the hw IRQ interfaces so that IRQ tracing sees
all of our changes.
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added 10GbE interface and clock nodes.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu updates from Tejun Heo:
"A lot of activities on percpu front. Notable changes are...
- percpu allocator now can take @gfp. If @gfp doesn't contain
GFP_KERNEL, it tries to allocate from what's already available to
the allocator and a work item tries to keep the reserve around
certain level so that these atomic allocations usually succeed.
This will replace the ad-hoc percpu memory pool used by
blk-throttle and also be used by the planned blkcg support for
writeback IOs.
Please note that I noticed a bug in how @gfp is interpreted while
preparing this pull request and applied the fix 6ae833c7fe
("percpu: fix how @gfp is interpreted by the percpu allocator")
just now.
- percpu_ref now uses longs for percpu and global counters instead of
ints. It leads to more sparse packing of the percpu counters on
64bit machines but the overhead should be negligible and this
allows using percpu_ref for refcnting pages and in-memory objects
directly.
- The switching between percpu and single counter modes of a
percpu_ref is made independent of putting the base ref and a
percpu_ref can now optionally be initialized in single or killed
mode. This allows avoiding percpu shutdown latency for cases where
the refcounted objects may be synchronously created and destroyed
in rapid succession with only a fraction of them reaching fully
operational status (SCSI probing does this when combined with
blk-mq support). It's also planned to be used to implement forced
single mode to detect underflow more timely for debugging.
There's a separate branch percpu/for-3.18-consistent-ops which cleans
up the duplicate percpu accessors. That branch causes a number of
conflicts with s390 and other trees. I'll send a separate pull
request w/ resolutions once other branches are merged"
* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (33 commits)
percpu: fix how @gfp is interpreted by the percpu allocator
blk-mq, percpu_ref: start q->mq_usage_counter in atomic mode
percpu_ref: make INIT_ATOMIC and switch_to_atomic() sticky
percpu_ref: add PERCPU_REF_INIT_* flags
percpu_ref: decouple switching to percpu mode and reinit
percpu_ref: decouple switching to atomic mode and killing
percpu_ref: add PCPU_REF_DEAD
percpu_ref: rename things to prepare for decoupling percpu/atomic mode switch
percpu_ref: replace pcpu_ prefix with percpu_
percpu_ref: minor code and comment updates
percpu_ref: relocate percpu_ref_reinit()
Revert "blk-mq, percpu_ref: implement a kludge for SCSI blk-mq stall during probe"
Revert "percpu: free percpu allocation info for uniprocessor system"
percpu-refcount: make percpu_ref based on longs instead of ints
percpu-refcount: improve WARN messages
percpu: fix locking regression in the failure path of pcpu_alloc()
percpu-refcount: add @gfp to percpu_ref_init()
proportions: add @gfp to init functions
percpu_counter: add @gfp to percpu_counter_init()
percpu_counter: make percpu_counters_lock irq-safe
...
Pull libata update from Tejun Heo:
"AHCI is getting per-port irq handling and locks for better
scalability. The gain is not huge but measureable with multiple high
iops devices connected to the same host; however, the value of
threaded IRQ handling seems negligible for AHCI and it likely will
revert to non-threaded handling soon.
Another noteworthy change is George Spelvin's "libata: Un-break ATA
blacklist". During 3.17 devel cycle, the libata blacklist glob
matching got generalized and rewritten; unfortunately, the patch
forgot to swap arguments to match the new match function and ended up
breaking blacklist matching completely. It got noticed only a couple
days ago so it couldn't make for-3.17-fixes either. :(
Other than the above two, nothing too interesting - the usual cleanup
churns and device-specific changes"
* 'for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
pata_serverworks: disable 64-KB DMA transfers on Broadcom OSB4 IDE Controller
libata: Un-break ATA blacklist
AHCI: Do not acquire ata_host::lock from single IRQ handler
AHCI: Optimize single IRQ interrupt processing
AHCI: Do not read HOST_IRQ_STAT reg in multi-MSI mode
AHCI: Make few function names more descriptive
AHCI: Move host activation code into ahci_host_activate()
AHCI: Move ahci_host_activate() function to libahci.c
AHCI: Pass SCSI host template as arg to ahci_host_activate()
ata: pata_imx: Use the SIMPLE_DEV_PM_OPS() macro
AHCI: Cleanup checking of multiple MSIs/SLM modes
libata-sff: Fix controllers with no ctl port
ahci_xgene: Fix the error print invalid resource for APM X-Gene SoC AHCI SATA Host Controller driver.
libata: change ata_<foo>_printk routines to return void
ata: qcom: Add device tree bindings information
ahci-platform: Bump max number of clocks to 5
ahci: ahci_p5wdh_workaround - constify DMI table
libahci_platform: Staticize ahci_platform_<en/dis>able_phys()
pata_platform: Remove useless irq_flags field
pata_of_platform: Remove "electra-ide" quirk
...
Now that we support read-only memslots, we need to make sure that
pass-through device mappings are not mapped writable if the guest
has requested them to be read-only. The existing implementation
already honours this by calling kvm_set_s2pte_writable() on the new
pte in case of writable mappings, so all we need to do is define
the default pgprot_t value used for devices to be PTE_S2_RDONLY.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that we support read-only memslots, we need to make sure that
pass-through device mappings are not mapped writable if the guest
has requested them to be read-only. The existing implementation
already honours this by calling kvm_set_s2pte_writable() on the new
pte in case of writable mappings, so all we need to do is define
the default pgprot_t value used for devices to be PTE_S2_RDONLY.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Add support for read-only MMIO passthrough mappings by adding a
'writable' parameter to kvm_phys_addr_ioremap. For the moment,
mappings will be read-write even if 'writable' is false, but once
the definition of PAGE_S2_DEVICE gets changed, those mappings will
be created read-only.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Handle the potential NULL return value of find_vma_intersection()
before dereferencing it.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Merge patch-bomb from Andrew Morton:
- part of OCFS2 (review is laggy again)
- procfs
- slab
- all of MM
- zram, zbud
- various other random things: arch, filesystems.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
nosave: consolidate __nosave_{begin,end} in <asm/sections.h>
include/linux/screen_info.h: remove unused ORIG_* macros
kernel/sys.c: compat sysinfo syscall: fix undefined behavior
kernel/sys.c: whitespace fixes
acct: eliminate compile warning
kernel/async.c: switch to pr_foo()
include/linux/blkdev.h: use NULL instead of zero
include/linux/kernel.h: deduplicate code implementing clamp* macros
include/linux/kernel.h: rewrite min3, max3 and clamp using min and max
alpha: use Kbuild logic to include <asm-generic/sections.h>
frv: remove deprecated IRQF_DISABLED
frv: remove unused cpuinfo_frv and friends to fix future build error
zbud: avoid accessing last unused freelist
zsmalloc: simplify init_zspage free obj linking
mm/zsmalloc.c: correct comment for fullness group computation
zram: use notify_free to account all free notifications
zram: report maximum used memory
zram: zram memory size limitation
zsmalloc: change return value unit of zs_get_total_size_bytes
zsmalloc: move pages_allocated to zs_pool
...
The different architectures used their own (and different) declarations:
extern __visible const void __nosave_begin, __nosave_end;
extern const void __nosave_begin, __nosave_end;
extern long __nosave_begin, __nosave_end;
Consolidate them using the first variant in <asm/sections.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the IRQF_DISABLED flag from FRV architecture code. It's a NOOP
since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frv has a macro named cpu_data, interfering with variables and struct
members with the same name:
include/linux/pm_domain.h:75:24: error: expected identifier or '('
before '&' token
struct gpd_cpu_data *cpu_data;
As struct cpuinfo_frv, boot_cpu_data, cpu_data, and current_cpu_data are
not used, removed them to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Performing vma lookups without taking the mm->mmap_sem is asking for
trouble. While doing the search, the vma in question can be modified or
even removed before returning to the caller. Take the lock (shared) in
order to avoid races while iterating through the vmacache and/or rbtree.
In addition, this guarantees that the address space will remain intact
during the CPU flushing.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Activate the RCU fast_gup for ARM64. We also need to force THP splits to
broadcast an IPI s.t. we block in the fast_gup page walker. As THP
splits are comparatively rare, this should not lead to a noticeable
performance degradation.
Some pre-requisite functions pud_write and pud_page are also added.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to implement fast_get_user_pages we need to ensure that the page
table walker is protected from page table pages being freed from under it.
This patch enables HAVE_RCU_TABLE_FREE, any page table pages belonging to
address spaces with multiple users will be call_rcu_sched freed. Meaning
that disabling interrupts will block the free and protect the fast gup
page walker.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Activate the RCU fast_gup for ARM. We also need to force THP splits to
broadcast an IPI s.t. we block in the fast_gup page walker. As THP
splits are comparatively rare, this should not lead to a noticeable
performance degradation.
Some pre-requisite functions pud_write and pud_page are also added.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to implement fast_get_user_pages we need to ensure that the page
table walker is protected from page table pages being freed from under it.
This patch enables HAVE_RCU_TABLE_FREE, any page table pages belonging to
address spaces with multiple users will be call_rcu_sched freed. Meaning
that disabling interrupts will block the free and protect the fast gup
page walker.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need a mechanism to tag ptes as being special, this indicates that no
attempt should be made to access the underlying struct page * associated
with the pte. This is used by the fast_gup when operating on ptes as it
has no means to access VMAs (that also contain this information)
locklessly.
The L_PTE_SPECIAL bit is already allocated for LPAE, this patch modifies
pte_special and pte_mkspecial to make use of it, and defines
__HAVE_ARCH_PTE_SPECIAL.
This patch also excludes special ptes from the icache/dcache sync logic.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DMA-mapping supports CMA regions places either in low or high memory, so
there is no longer needed to limit default CMA regions only to low memory.
The real limit is still defined by architecture specific DMA limit.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neither CMA nor noncoherent allocations support atomic allocations.
Add a dedicated atomic pool to support this.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Riley <davidriley@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ritesh Harjain <ritesh.harjani@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARM currently uses a bitmap for tracking atomic allocations. genalloc
already handles this type of memory pool allocation so switch to using
that instead.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Riley <davidriley@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ritesh Harjain <ritesh.harjani@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For architectures without coherent DMA, memory for DMA may need to be
remapped with coherent attributes. Factor out the the remapping code from
arm and put it in a common location to reduce code duplication.
As part of this, the arm APIs are now migrated away from
ioremap_page_range to the common APIs which use map_vm_area for remapping.
This should be an equivalent change and using map_vm_area is more correct
as ioremap_page_range is intended to bring in io addresses into the cpu
space and not regular kernel managed memory.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Riley <davidriley@chromium.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Ritesh Harjain <ritesh.harjani@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Mitchel Humpherys <mitchelh@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARCH_USES_NUMA_PROT_NONE was defined for architectures that implemented
_PAGE_NUMA using _PROT_NONE. This saved using an additional PTE bit and
relied on the fact that PROT_NONE vmas were skipped by the NUMA hinting
fault scanner. This was found to be conceptually confusing with a lot of
implicit assumptions and it was asked that an alternative be found.
Commit c46a7c81 "x86: define _PAGE_NUMA by reusing software bits on the
PMD and PTE levels" redefined _PAGE_NUMA on x86 to be one of the swap PTE
bits and shrunk the maximum possible swap size but it did not go far
enough. There are no architectures that reuse _PROT_NONE as _PROT_NUMA
but the relics still exist.
This patch removes ARCH_USES_NUMA_PROT_NONE and removes some unnecessary
duplication in powerpc vs the generic implementation by defining the types
the core NUMA helpers expected to exist from x86 with their ppc64
equivalent. This necessitated that a PTE bit mask be created that
identified the bits that distinguish present from NUMA pte entries but it
is expected this will only differ between arches based on _PAGE_PROTNONE.
The naming for the generic helpers was taken from x86 originally but ppc64
has types that are equivalent for the purposes of the helper so they are
mapped instead of duplicating code.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the use of the IRQF_DISABLED flag
from arch/m32r/kernel/time.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
Mike Rapoport