Tegra114's AHUB shares a design with Tegra30, with the followin changes:
* Supports more (10 vs. 4) bi-directional FIFO channels into RAM.
* Requires a separate block of registers to support the above.
* Supports more attached clients, i.e. new audio multiplexing and
de-multiplexing modules.
* Is affected by more clocks due to the above.
This change fully defines the device tree binding changes required to
represent these changes, and minimally extends the driver to support
the new hardware, without exposing any of the new FIFO channels.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This register field is 11 bits wide, not 15 bits wide. Given the way
this value is currently, used, this patch has no practical effect.
However, it's still best if the value is correct.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra only supports, and always enables, device tree. Remove all runtime
checks for DT support from the driver.
This allows removal of the hard-coded Harmony ASoC mapping table, since
Harmony only boots with DT now.
All board-specific configuration now comes from device tree, so there is
no need to have a platform_data structure. Rework the driver to parse the
device tree directly into struct tegra_wm8903.
Also some slight re-ordering of probe() so that the code more closely
resembles other drivers for easier comparison. Inparticular, the GPIO DT
parsing and initial programming are moved together for each GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra only supports, and always enables, device tree. Remove all runtime
checks for DT support from the driver.
Also, some minor changes so that the probe() body more closely resembles
other drivers, for easier comparison.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra only supports, and always enables, device tree. Remove all runtime
checks for DT support from the driver.
Also, various minor cleanups so that the probe() body more closely
resembles other drivers, for easier comparison.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra only supports, and always enables, device tree. Remove all runtime
checks for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Various minor cleanups so that the probe() body more closely resembles
other drivers, for easier comparison.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra only supports, and always enables, device tree. Remove all runtime
checks for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
Configlink clock information is added to device tree. Get the clocks
using device node. Remove AUXDATA.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
'tegra30_i2s_startup' and 'tegra30_i2s_shutdown' are used only in this file and
hence made static. Fixes the following sparse warnings:
sound/soc/tegra/tegra30_i2s.c:74:5: warning:
symbol 'tegra30_i2s_startup' was not declared. Should it be static?
sound/soc/tegra/tegra30_i2s.c:101:6: warning:
symbol 'tegra30_i2s_shutdown' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following sparse warnings:
sound/soc/tegra/tegra30_ahub.c:583:16: warning:
Using plain integer as NULL pointer
sound/soc/tegra/tegra30_ahub.c:600:16: warning:
Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
__devinitconst has been removed from the kernel and gives
the following build errors:
sound/soc/tegra/tegra20_ac97.c:460:58: error: Expected ; at end of declaration
sound/soc/tegra/tegra20_ac97.c:460:58: error: got __devinitconst
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This has been removed from the kernel recently and gives following build errors:
sound/soc/tegra/tegra_wm9712.c:155:58: error:
expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘__devinitconst’
sound/soc/tegra/tegra_wm9712.c:165:21: error:
‘tegra_wm9712_of_match’ undeclared here (not in a function)
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds a very simple machine driver using the Wolfson wm9712 AC97
codec.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds the driver for the Tegra 2x AC97 host controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This connection is used by the AC97 controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AC97 uses a fixed rate, unrelated to the sample rate. Add a function to
make the setup more trivial.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=IIsz
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinitconst is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove includes of <mach/dma.h> from sound/soc; nothing from it is used.
Remove include of <mach/dma.h> from mach-tegra/apbio.c; since the DMA
transfers made by this file don't need flow-control with any peripheral,
there's no need to set any slave ID.
Once those changes are made, there are no remaining users of <mach/dma.h>
so remove it. Drivers should get this information from device tree. This
removal is necessary for single zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
Remove the support code which uses the legacy APB DMA driver
for accessing the I2S FIFO.
The driver will use the dmaengine based APB DMA driver for
accessing reqding/writing to I2S FIFO.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The I2S controllers are programmed with an "attention" level of 4 DWORDs.
This must match the configuration passed to the DMA driver, so that when
they burst in data, they don't overflow the available FIFO space. Also,
the burst size is relevant to the destination for playback, and source
for capture, not vice-versa as originally written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Move the Tegra+WM8903 ASoC platform data header out of
arch/arm/mach-tegra, as a pre-requisite of single zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both the schematics and practical testing show that the HP detect GPIO
is high when the headphones are plugged in. Hence, the snd_soc_jack_gpio
should not specify to invert the signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org> # v3.4 v3.5
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pxAa
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-3.6
ASoC: Additional updates for 3.6
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
A bunch of small fixes for ASoC, mainly against regressions due to the
defaulting regmap i/o, in addition to a HD-audio fixup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=XuSA
-----END PGP SIGNATURE-----
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A bunch of small fixes for ASoC, mainly against regressions due to the
defaulting regmap i/o, in addition to a HD-audio fixup."
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: core: Fix check before defaulting to regmap
ALSA: hda - Support dock on Lenovo Thinkpad T530 with ALC269VC
ASoC: wm8962: Allow VMID time to fully ramp
ASoC: AC97 doesn't use regmap by default
ASoC: sgtl5000: enable VAG_POWER for LINE_IN
ASoC: ab8500: Inform SoC Core that we have our own I/O arrangements
ASoC: omap: Add missing modules aliases to get sound working on omap devices
sound: tegra_alc5632: Adjust to of_get_named_gpio() change
sound: tegra_wm8903: Adjust to of_get_named_gpio() change
ASoC: mc13783: Provide codec->control_data
ASoC: ux500: Include the correct header files
ASoC: wm8994: Hold runtime PM reference while handling mic and jack IRQs
ASoC: sgtl5000: remove unneeded snd_soc_dapm_new_widgets in probe
ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work
ASoC: mxs-saif: fix clock prepare and enable unbalance issue
ASoC: wm8994: Ensure there are enough BCLKs for four channels
of_get_named_gpio() was changed to return -EPROBE_DEFER in case of
gpios not probed yet. This patch adjusts tegra_alc5632 to this.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_named_gpio() was changed to return -EPROBE_DEFER in case of
gpios not probed yet. This patch adjusts tegra_wm8903 to this.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a fairly quiet release in all sound area. Only a little bit
of changes in the core side while most of changes are seen in the
drivers.
HD-audio:
- A few new codec additions for Nvidia, Realtek and VIA
- Intel Haswell audio support
- Support for "phantom" jacks for consistent jack reporting
- Major clean-ups in HDMI/DP driver codes
- A workaround for inverted digital-mic pins with Realtek codecs
- Removal of beep_mode=2 option
ASoC:
- Added the ability to add and remove DAPM paths dynamically, mostly
for reparenting on clock changes
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500,
TI Isabelle and Wolfson Microelectronics WM5102 and WM5110
- DAPM fixes for the recent locking changes
- Fix for _PRE and _POST widgets (which have been broken for a few
releases now)
- A couple of minor driver updates
Misc
- Conversion to new dev_pm_ops in platform and PCI drivers
- LTC support and some fixes in PCXHR driver
- A few fixes and PM support for ISA OPti9xx and WSS cards
- Some TLV code cleanup
- Move driver-specific headers from include/sound to local dirs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=N0aj
-----END PGP SIGNATURE-----
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound update from Takashi Iwai:
"This is a fairly quiet release in all sound area. Only a little bit
of changes in the core side while most of changes are seen in the
drivers.
HD-audio:
- A few new codec additions for Nvidia, Realtek and VIA
- Intel Haswell audio support
- Support for "phantom" jacks for consistent jack reporting
- Major clean-ups in HDMI/DP driver codes
- A workaround for inverted digital-mic pins with Realtek codecs
- Removal of beep_mode=2 option
ASoC:
- Added the ability to add and remove DAPM paths dynamically, mostly
for reparenting on clock changes
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500,
TI Isabelle and Wolfson Microelectronics WM5102 and WM5110
- DAPM fixes for the recent locking changes
- Fix for _PRE and _POST widgets (which have been broken for a few
releases now)
- A couple of minor driver updates
Misc
- Conversion to new dev_pm_ops in platform and PCI drivers
- LTC support and some fixes in PCXHR driver
- A few fixes and PM support for ISA OPti9xx and WSS cards
- Some TLV code cleanup
- Move driver-specific headers from include/sound to local dirs"
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (212 commits)
ASoC: dapm: Fix _PRE and _POST events for DAPM performance improvements
ALSA: hda - add dock support for Thinkpad X230 Tablet
ALSA: hda - Turn on PIN_OUT from hdmi playback prepare.
ASoC imx-audmux: add MX31_AUDMUX_PORT7_SSI_PINS_7 define
ASoC: littlemill: Add userspace control of the WM1250 I/O
ASoC: wm8994: Update micdet for irqdomain conversion
ALSA: hda - make sure alc268 does not OOPS on codec parse
ALSA: hda - Add support for Realtek ALC282
ALSA: hda - Fix index number conflicts of phantom jacks
ALSA: opti9xx: Fix section mismatch by PM support
ALSA: snd-opti9xx: Implement suspend/resume
ALSA: hda - Add new GPU codec ID to snd-hda
ALSA: hda - Fix driver type of Haswell controller to AZX_DRIVER_SCH
ALSA: hda - add Haswell HDMI codec id
ALSA: hda - Add DeviceID for Haswell HDA
ALSA: wss_lib: Fix resume on Yamaha OPL3-SAx
ALSA: wss_lib: fix suspend/resume
ALSA: es1938: replace TLV_DB_RANGE_HEAD with DECLARE_TLV_DB_RANGE
ALSA: tlv: add DECLARE_TLV_DB_RANGE()
ALSA: tlv: add DECLARE_TLV_CONTAINER()
...
From Stephen Warren <swarren@wwwdotorg.org>:
This branch contains numerous changes required as a baseline in order to
convert Tegra to the common clock framework. The intention was to also
include patches to actually convert Tegra to the common clock framework.
However, those patches appeared late in the kernel cycle and currently
cause regressions on some boards, so were dropped for now.
* 'for-3.6/common-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
mmc: tegra: add clk_prepare/clk_unprepare
i2c: tegra: Add clk_prepare/clk_unprepare
ARM: tegra: add clk_prepare/clk_unprepare
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI fifo and memory in
place of legacy Tegra APB DMA.
Because generic soc-dmaengine-pcm uses the DMAs API
based on dmaengine, using the exported APIs provided
by this generic driver.
The new driver is selected if legacy driver is not
selected and new dma driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into for-3.6
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If mic detect is left enabled and the WM8903 detects a status change,
the WM8903 driver will make a callback against the free()d jack, which
will cause a crash.
This problem can be triggered by fully initializing an audio card, then
removing and re-inserting the machine driver module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Tegra ASoC machine drivers only depend on Tegra architecture support
to compile, not specific board support. Remove Kconfig dependencies on
any particular board. This is required since Kconfig options for boards
are going away given the migration to device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the module to automatically load when instantiated from
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stop open-coding the caching of the ctrl registers; instead, use
regmap_update_bits() to update parts of the register from different
places. The removal of the open-coded cache will allow controls to be
created which touch registers, which will be necessary if any of these
modules are converted to CODECs.
Get rid of tegra*_read/write; just call regmap_read/write directly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the actual device of the I2S or SPDIF controller reporting the
problem. If a future change converts these controllers to be CODECs, then
there may be no pcm associated with the substream, so this change avoids
a crash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rtd->codec_dai->codec can be used instead.
This is a slight step along the way to not needing the rtd->codec field
any more.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Define the DAI format statically in the dai_link, rather than executing
code to set it each time the hw params are set.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is certainly required if the I2S and SPDIF controllers are converted
to be CODECs, and is probably good practice irrespective.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prior to this patch, the CPU side of a DAI link was specified using a
single name. Often, this was the result of calling dev_name() on the
device providing the DAI, but in the case of a CPU DAI driver that
provided multiple DAIs, it needed to mix together both the device name
and some device-relative name, in order to form a single globally unique
name.
However, the CODEC side of the DAI link was specified using separate
fields for device (name or OF node) and device-relative DAI name.
This patch allows the CPU side of a DAI link to be specified in the same
way as the CODEC side, separating concepts of device and device-relative
DAI name.
I believe this will be important in multi-codec and/or dynamic PCM
scenarios, where a single CPU driver provides multiple DAIs, while also
booting using device tree, with accompanying desire not to hard-code the
CPU side device's name into the original .cpu_dai_name field.
Ideally, both the CPU DAI and CODEC DAI loops in soc_bind_dai_link()
would now be identical. However, two things prevent that at present:
1) The need to save rtd->codec for the CODEC side, which means we have
to search for the CODEC explicitly, and not just the CODEC side DAI.
2) Since we know the CODEC side DAI is part of a codec, and not just
a standalone DAI, it's slightly more efficient to convert .codec_name/
.codec_of_node into a codec first, and then compare each DAI's .codec
field, since this avoids strcmp() on each DAI's CODEC's name within
the loop.
However, the two loops are essentially semantically equivalent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In kernel 3.6, Seaboard will only be supported when booting using device
tree; the board files are being removed. Hence, remove the non-DT support
for Seaboard and derivatives Kaen and Aebl from the audio driver.
Harmony is the only remaining board supported by this driver when not
using DT. This support is currently scheduled for removal in 3.7.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By the time any widget callbacks could be called, if the GPIO ID they
will manipulate is valid, it must have already been requested, or the
card would have failed to probe or initialize. So, testing for GPIO
validity is equivalent to testing whether the GPIO was successfully
requested at this point in the code. Making this change will allow later
patches to remove the gpio_requested variable.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The headphone jack GPIOs are added/initialized in the DAI link's init()
method, and hence in theory may not always have been added before remove()
is called in some unusual cases. In order to prevent calling
snd_soc_jack_free_gpios() if snd_soc_jack_add_gpios() had not been, the
code kept track of the initialization state to avoid the free call when
necessary.
However, it appears that snd_soc_jack_free_gpios() is robust in the face
of being called without snd_soc_jack_add_gpios() first succeeding, so
there is little point manually tracking this information. Hence, remove
the tracking code. All other machine drivers already operate this way.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that deferred probe exists, we can parse device tree and request
GPIOs from probe(), rather than deferring this to the DAI link's init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The headphone jack GPIOs are added/initialized in the DAI link's init()
method, and hence in theory may not always have been added before remove()
is called in some unusual cases. In order to prevent calling
snd_soc_jack_free_gpios() if snd_soc_jack_add_gpios() had not been, the
code kept track of the initialization state to avoid the free call when
necessary.
However, it appears that snd_soc_jack_free_gpios() is robust in the face
of being called without snd_soc_jack_add_gpios() first succeeding, so
there is little point manually tracking this information. Hence, remove
the tracking code. Almost all other machine drivers already operate this
way.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By using this function, the driver no longer needs to explicitly free
the GPIOs. Hence, we can also remove the flags we use to track whether
we allocated these GPIOs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that deferred probe exists, we can parse device tree and request
GPIOs from probe(), rather than deferring this to the DAI link's init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This binding doesn't include the nvidia,model or nvidia,audio-routing
properties the other Tegra audio DT bindings have, because this binding
is targetted at a single machine, rather than for any machine using the
tlv320aic23 codec.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All Tegra ASoC drivers will be reworked to use MMIO regmaps. Select
this in Kconfig.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds Kconfig options for the Tegra30 AHUB and I2S controller, and
updates the Tegra+WM8903 machine driver Kconfig to select those.
Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This provides an ASoC DAI interface for Tegra 30's I2S controller.
Includes a squashed bugfix from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The AHUB (Audio Hub) is a mux/crossbar which links all audio-related
devices except the HDA controller on Tegra30. The devices include the
DMA FIFOs, DAM (Digital Audio Mixers), I2S controllers, and SPDIF
controller. Audio data may be routed between these devices in various
combinations as required by board design/application.
Includes a squashed bugfix from Nikesh Oswal <noswal@nvidia.com>
Includes squashed bugfixes from Sumit Bhattacharya <sumitb@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent list discussions concluded that drivers should not be calling
of_have_populated_dt(), and hence of_have_populated_dt() should not be
exported. Use a different mechanism to detect DT vs. non-DT boot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tegra30 has some additional clocks that need to be manipulated, names
some clocks differently, runs PLLs at different base rates, etc. The
utility code needs to handle this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize the audio clock tree appropriately for some reasonable rate.
This makes sure the PLLs etc. are actually programmed to something
reasonable when the audio driver is loaded.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename Tegra20-specific Kconfig variables, module filenames, all internal
symbol names, clocks, and platform devices, to reflect the fact the DAS
and I2S drivers are for a specific HW version.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename these files so they include a specific hardware version in their
filenames. The contents is only touched minimally so that git's rename
tracking operates correctly; renaming all symbols in the files results
in a diff so large that the rename detection fails.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this, the Tegra20 drivers can be built into a kernel that's
built only for Tegra30.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAS, I2S, and SPDIF Kconfig options are intended to be selected by
the Kconfig options for ASoC machine drivers. As such, they don't need
to be user-visible themselves. Drop the description from the DAS variable
to achieve this. I2S and SPDIF already don't have a description.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_enable/disable() already reference count the enable calls, so there's
no need for the callers to do the same.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAS, I2S, and SPDIF drivers are Tegra20-specific. Group these
together so that when Tegra30-specific equivalents are added later, the
file ordering makes sense.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is mainly for symmetry with a future Tegra30 driver, where the
equivalent of the DAS (the AHUB) is useful separately from the I2S driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ERROR: trailing whitespace
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indent with TABs to be consistent with the rest of the file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These include aren't needed, and some of the files are about to be
renamed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously, the ASoC 'platform' (PCM/DMA) object was instantiated via a
platform_device. This didn't represent the hardware well, since there
was no separate hardware associated with this platform_device; it was a
virtual device with sole purpose to call snd_soc_register_platform().
This mechanism required all board files to register this device, and all
ASoC machine drivers to create and register this device when booting
using device tree.
This change removes the platform_device completely. Each Tegra DAI now
registers the ASoC 'platform' itself. Machine drivers are adjusted for
the new 'platform' name.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix comment indentation to clear checkpatch errors in a later patch.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following warning:
sound/soc/tegra/tegra_alc5632.c: In function 'tegra_alc5632_asoc_init':
sound/soc/tegra/tegra_alc5632.c:118:6: warning: unused variable 'ret' [-Wunused-variable]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALC5632 codec supports digital microphone. This patch adds DAPM widget.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All DAPM routes are configured via device tree, and there is no need in
DAPM route structures in board file.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements device tree support for Tegra boards with ALC5632
codec.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a follow up on 53dea36c70 which fixes the other affected
pcm engines.
Description from 53dea36c70c1857:
Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Without this patch I was seeing null-pointer dereferenc in atmel-pcm.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver is parameterized in two ways:
a) Platform data, which supplies the set of GPIOs used by the driver.
These GPIOs can now be parsed out of device tree.
b) Machine-specific DAPM route arrays embedded into the ASoC machine
driver itself. Historically, the driver picks the appropriate array
to use using machine_is_*(). The driver now requires this array to
be parsed from device tree when instantiated through device tree,
using the core ASoC support for this parsing.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At this stage only Toshiba AC100/Dynabook supported.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move DAS routing setup into the DAS driver itself. This removes the need
to duplicate this in each machine driver, of which we'll soon have three.
An added advantage is that the machine drivers no longer call the Tegra20-
specific DAS functions by name, so the machine driver no longer needs to
be split up into Tegra20 and Tegra30 versions.
If individual machine drivers need a different routing setup to this
default, they can still call the DAS functions to set that up.
Long-term, DAS will be a codec driver, and user-space will be able to
control its routing, possibly within constraints that the machine driver
sets up. Configuring the DAS routing from the DAS driver is a very slight
move in that direction.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the module_platform_driver() macro which makes
the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename it to MICBIAS to reflect the pin name and help any out of tree
users notice the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Set card.fully_routed to request the ASoC core calculated unused codec
pins, and call snd_soc_dapm_nc_pin() for them. Remove the open-coded
calls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set card.fully_routed to request the ASoC core calculated unused codec
pins, and call snd_soc_dapm_nc_pin() for them. Remove the open-coded
calls.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When devices are instantiated from device-tree, pdev->id is set to -1.
Rework the driver so it doesn't depend on the ID.
Tegra I2S instantiated from board files are configured with pdev
name "tegra-i2s" and ID 0 or 1. The driver core then names the
device "tegra-i2s.0" or "tegra-i2s.1". This is not changing.
When a device is instantiated from device-tree, it will have
pdev->name="" and pdev->id=-1. For this reason, the pdev->id value is
not something we can rely on.
This patch doesn't actually change any names though:
When a device is instantiated from device-tree, the overall device name
will be "${unit_address}.${node_name}". This causes issues such as
clk_get() failures due to lack of a device-name match. To solve that,
AUXDATA was invented, to force a specific device name, thus allowing
dev_name() to return the same as the non-device-tree case. Tegra
currently uses AUXDATA for the I2S controllers. Eventually, AUXDATA will
go away, most likely replaced by phandle-based references within the
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_driver saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_driver saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_drive saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This removes potentially machine-specific routing knowledge from the
I2S driverinto the machine drivers, which is better equipped to know
what the appropriate routing configuration is.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_platform_drive saves some boiler-plate code.
The devm_ APIs remove the need to manually clean up allocations,
thus removing some code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Fixes the following sparse warnings:
sound/soc/tegra/tegra_das.c:215:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_das.c:237:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_pcm.c:370:32: warning: symbol 'tegra_pcm_platform' was not declared. Should it be static?
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.
OMAP drivers are omitted as I know Peter already has patches for them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two issues were preventing module snd-soc-tegra-wm8903.ko from being
removed and re-inserted:
a) The speaker-enable GPIO is hosted by the WM8903 chip. This GPIO must
be freed before snd_soc_unregister_card() is called, because that
triggers wm8903.c:wm8903_remove(), which calls gpiochip_remove(), which
then fails if any of the GPIOs are in use. To solve this, free all GPIOs
first, so the code doesn't care where they come from.
b) We need to call snd_soc_jack_free_gpios() to match the call to
snd_soc_jack_add_gpios() during initialization. Without this, the
call to snd_soc_jack_add_gpios() fails during any subsequent modprobe
and initialization, since the GPIO and IRQ are already registered. In
turn, this causes the headphone state not to be monitored, so the
headphone is assumed not to be plugged in, and the audio path to it is
never enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all PCM devices have all sub-streams. Specifically, the SPDIF driver
only supports playback and hence has no capture substream. Check whether
a substream exists before dereferencing it, when de-allocating DMA
buffers in tegra_pcm_deallocate_dma_buffer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This is a minimal driver for the Tegra SPDIF controller.
In hardware, the SPDIF output signal is always routed to any active HDMI
display controllers, and may also be routed to external pins on Tegra
using the pinmux.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The clock needed by the I2S driver is associated with the I2S device name
in the standard fashion. Hence, use clk_get(dev) instead of clk_get_sys(clk_name).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The I2S controller needs a clock to respond to register writes. Without
this, register writes will at worst hang the CPU. In practice, I've only
observed writes being dropped.
Luckily, the dropped register writes historically had no effect:
TEGRA_I2S_TIMING: The value we wrote was the reset default.
TEGRA_I2S_FIFO_SCR: The default was for the FIFOs to request more data
when one slot was empty. The requested value was for the FIFOs to request
when four slots were empty. The DMA controller in the mainline kernel is
configured to burst a single entry at a time into the FIFO, hence there
was no issue. The only negative effect was on bus efficiency losses due
to an increased number of arbitration attempts.
However, in various non-upstream changes, the DMA controller now bursts
four entries at a time into the FIFO. If there is only space for one
entry, the data is simply dropped. In practice, this resulted in 3/4 of
samples being dropped, and playback at 4x the expected rate and pitch.
By fixing the clocking issue, this is solved.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently pcm_new() passes in 3 arguments :- card, pcm and DAI.
Refactor this to only pass in 1 argument (i.e. the rtd) since struct rtd contains
card, pcm and DAI along with other members too that are useful too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We want the default state of the HP_MUTE signal to be asserted, so that
the headphones are muted before the first audio playback. Without this,
the headphones are left unmuted until shortly after the first audio
playback completes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The prototype of the inline dummy version of tegra_i2s_debug_add
was not consistent with the real version.
Reported-by: Rhyland-Klein <rklein@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There needs to be a strong reason for overriding the Kconfig default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
CONFIG_SND_SOC_TEGRA_WM8903 is useful for many Tegra boards. To avoid the
ASoC tegra/Kconfig enumerating them all, instead have the Tegra machine
Kconfig select MACH_HAS_SND_SOC_TEGRA_WM8903 where appropriate, and have
SND_SOC_TEGRA_WM8903 depend on this.
[Redid ASoC diff so it applies. -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace calls to a variety of registration functions by updating
struct snd_soc_card snd_soc_tegra_wm8903 to directly point at the
various control/widget/map tables instead. The ASoC core now
performs any required registration based on these data fields.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Card widgets are created in the card's DAPM context, not any codec's DAPM
context. Hence, w->codec==NULL. Instead, find the card from the widget
through the DAPM context of the widget, not the codec of the widget.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only the clock programming code needs to know whether the clocks changed,
and that is encapsulated within tegra_asoc_utils_set_rate(). The machine
driver's call to snd_soc_dai_set_sysclk(codec_dai, ...) is safe
irrespective of whether the clocks changed.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the driver is not initialized/registered, nothing should be touching
these fields anyway, so there's no point clearing them out.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This machine driver is a platform driver, and hence will only be
instantiated on the correct machines. Hence, there is no need to
check the current machine during probe.
(Applying Mark's TrimSlice review comments to the existing driver)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Ventana is identical to Harmony.
* Seaboard, Kaen, and Aebl are all pretty similar, mainly with slightly
different sets of GPIOs, and slightly different WM8903 pin connectivity.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Storing the struct in an array makes the assignments to the GPIO member a
little non-obvious, and is pointless when there's only a single GPIO.
(I thought I fixed this during the review cycle when first submitting this
driver, but I guess I overlooked that)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The previous commit renames SND_TEGRA_SOC_HARMONY to SND_TEGRA_SOC_WM8903.
While we're breaking people's .config files, rename all Tegra/SOC-related
Kconfig variables to be more consistent with at least the core codec
variables. Note that there exist machines that name their variables both
ways.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the file in advance to reflect this.
Fix the content of tegra_wm8903.c to match the rename; replace references
to Harmony board with something more generic.
* s/struct tegra_harmony/struct tegra_wm8903/
* s/harmony/machine/ # variable name
* Similar rename for some functions
* Similar comment fix
* Similar MODULE_DESCRIPTION fix
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Soon, this machine driver will be updated to handle a number of Tegra boards
using the WM8903 codec. Rename the platform device in advance to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The audio driver will soon support more than just the Tegra Harmony board.
Rename the platform data header file and data type to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC machine drivers that are their own platform_driver (as opposed to
those using the soc-audio platform_driver) need to explicitly set up
power-management operation callbacks.
To avoid cut/paste, snd_soc_pm_ops also needs to be exported.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tegra_dma_allocate_channel() returns NULL on errors, not an error pointer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The utilities will be required by every machine driver. Including the
utility object directly into every machine driver causes a build failure
if the modules are actually built into the kernel, since each will define
the symbols exported by the utility file. Solve this by moving the
utility object into a separate module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With the appropriate MODULE_ALIAS in place, the audio modules will be
automatically loaded; there is no longer a need for manual modprobes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Harmony has both an external mic (a regular mic jack) and an internal mic
(a 0.1" two-pin header on the board).
The external mic is connected to the WM8903's IN1L pin, and is supported
by the current driver.
The internal mic is connected to the WM8903's IN1R pin, and is not supported
by the current driver.
It appears that no Harmony systems were shipped with any internal mic
connected; users were expected to provide their own. This makes the
internal mic connection less interesting.
The WM8903's Mic Bias signal is used for both of these mics. For each mic,
a GPIO drives a transistor which gates whether the mic bias signal is
actively connected to that mic, or isolated from it.
The dual use of the mic bias for both mics makes a general-purpose complete
implementation of mic detection using the mic bias complex. So, for
simplicity, the internal mic is currently ignored by the driver.
This patch configures the relevant GPIOs to enable the mic bias connection
to the external mic, and disable the mic bias connection to the internal
mic. Note that in practice, this is the default state if these GPIOs aren't
configured.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* Add jack definition for mic jack
* Request wm8903 to enable mic detection
* Force mic bias on, since it's required for mic detection
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It causes noisy -codecs to appear in things like .codec_name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
gpio_set_value* should accept logic values not just 0 or 1. The WM8903 GPIO
driver has been fixed to work this way, so remove the redundant !!
previously required when it didn't accept values >1.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>