We can save a lot of code and pointers in the structs
by using debugfs_remove_recursive().
First, change cfg80211 to use debugfs_remove_recursive()
so that drivers do not need to clean up any files they
added to the per-wiphy debugfs (if and only if they are
ok to be accessed until after wiphy_unregister!).
Then also make mac80211 use debugfs_remove_recursive()
where necessary -- it need not remove per-wiphy files
as cfg80211 now removes those, but netdev etc. files
still need to be handled but can now be removed without
needing struct dentry pointers to all of them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When HT debugging is enabled and we receive a DelBA
frame we print out the reason code in the wrong byte
order. Fix that so we don't get weird values printed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addba timer function acquires the sta spinlock,
but at the same time we try to del_timer_sync() it
under the spinlock which can produce deadlocks.
To fix this, always del_timer_sync() the timer in
ieee80211_process_addba_resp() and add it again
after checking the conditions, if necessary.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IBSS code leaks a BSS struct after telling
cfg80211 about a given BSS by passing a frame.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (43 commits)
net: Fix 'Re: PACKET_TX_RING: packet size is too long'
netdev: usb: dm9601.c can drive a device not supported yet, add support for it
qlge: Fix firmware mailbox command timeout.
qlge: Fix EEH handling.
AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl (v2)
bonding: fix a race condition in calls to slave MII ioctls
virtio-net: fix data corruption with OOM
sfc: Set ip_summed correctly for page buffers passed to GRO
cnic: Fix L2CTX_STATUSB_NUM offset in context memory.
MAINTAINERS: rt2x00 list is moderated
airo: Reorder tests, check bounds before element
mac80211: fix for incorrect sequence number on hostapd injected frames
libertas spi: fix sparse errors
mac80211: trivial: fix spelling in mesh_hwmp
cfg80211: sme: deauthenticate on assoc failure
mac80211: keep auth state when assoc fails
mac80211: fix ibss joining
b43: add 'struct b43_wl' missing declaration
b43: Fix Bugzilla #14181 and the bug from the previous 'fix'
rt2x00: Fix crypto in TX frame for rt2800usb
...
This makes the mesh housekeeping timer work properly on big endian
systems.
Signed-off-by: Rui Paulo <rpaulo@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh portals proxy traffic for nodes external to the mesh. When a
proxied frame is received by a mesh interface, it should update its mesh
portal table. This was only happening for unicast frames. With this
change we also learn about mesh portals from proxied multicast frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace netif_tx_{start,stop,wake}_all_queues with the single-queue
equivalents (i.e. netif_{start,stop,wake}_queue). Since we are down to
a single queue, these should peform slightly better.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get rid of cookies in cfg80211_send_XXX() functions.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hostapd injects a frame, e.g. an authentication or association
response, mac80211 looks for a suitable access point virtual interface
to associate the frame with based on its source address. This makes it
possible e.g. to correctly assign sequence numbers to the frames.
A small typo in the ethernet address comparison statement caused a
failure to find a suitable ap interface. Sequence numbers on such
frames where therefore left unassigned causing some clients
(especially windows-based 11b/g clients) to reject them and fail to
authenticate or associate with the access point. This patch fixes the
typo in the address comparison statement.
Signed-off-by: Björn Smedman <bjorn.smedman@venatech.se>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo in the description of hwmp_route_info_get(), no function
changes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When association fails, we should stay authenticated,
which in mac80211 is represented by the existence of
the mlme work struct, so we cannot free that, instead
we need to just set it to idle.
(Brought to you by the hacking session at Kernel Summit 2009 in Tokyo,
Japan. -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commit "mac80211: fix logic error ibss merge bssid check" fixed
joining of ibss cell when static bssid is provided. In this case
ifibss->bssid is set before the cell is joined and comparing that address
to a bss should thus always succeed. Unfortunately this change broke the
other case of joining a ibss cell without providing a static bssid where
the value of ifibss->bssid is not set before the cell is joined.
Since ifibss->bssid may be set before or after joining the cell we do not
learn anything by comparing it to a known bss. Remove this check.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx() must be called with softirqs disabled
since the networking stack requires this for netif_rx()
and some code in mac80211 can assume that it can not
be processing its own tasklet and this call at the same
time.
It may be possible to remove this requirement after a
careful audit of mac80211 and doing any needed locking
improvements in it along with disabling softirqs around
netif_rx(). An alternative might be to push all packet
processing to process context in mac80211, instead of
to the tasklet, and add other synchronisation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan completes, we call ieee80211_sta_find_ibss(),
which is also called from other places. When the scan was
done in software, there's no problem as both run from the
single-threaded mac80211 workqueue and are thus serialised
against each other, but with hardware scan the completion
can be in a different context and race against callers of
this function from the workqueue (e.g. due to beacon RX).
So instead of calling ieee80211_sta_find_ibss() directly,
just arm the timer and have it fire, scheduling the work,
which will invoke ieee80211_sta_find_ibss() (if that is
appropriate in the current state).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
kfree_skb() should be used to free struct sk_buff pointers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.
Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.
Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having to modify every non-mac80211 for device type assignment,
do this inside the netdev notifier callback of cfg80211. So all drivers
that integrate with cfg80211 will export a proper device type.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following step-by step:
1. A STA authenticates and associates with the AP and exchanges
traffic.
2. The STA reports to the AP that it is going to PS state.
3. Some time later the STA device goes to the stand-by mode (not only
its wi-fi card, but the device itself) and drops the association state
without sending a disassociation frame.
4. The STA device wakes up and begins authentication with an
Auth frame as it hasn't been authenticated/associated previously.
At the step 4 the AP "remembers" the STA and considers it is still in
the PS state, so the AP buffers frames, which it has to send to the STA.
But the STA isn't actually in the PS state and so it neither checks
TIM bits nor reports to the AP that it isn't power saving.
Because of that authentication/[re]association fails.
To fix authentication/[re]association stage of this issue, Auth, Assoc
Resp and Reassoc Resp frames are transmitted disregarding of STA's power
saving state.
N.B. This patch doesn't fix further data frame exchange after
authentication/[re]association. A patch in hostapd is required to fix
that.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's useful to know the MAC address when being
disassociated; fix a typo (missing colon) and
move some messages so we get them only when they
are actually taking effect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the DTIM setting is read from beacons, mac80211 will
assume it is 1 if the TIM IE is not present or the value
is 0. This sounds fine, but the same function processes
probe responses as well, which don't have a TIM IE. This
leads to overwriting any values previously parsed out of
beacon frames.
Thus, instead of checking for the presence of the TIM IE
when setting the default, simply check whether the DTIM
period value is valid already. If the TIM IE is not there
then the value cannot be valid (it is initialised to 0)
and probe responses received after beacons will not lead
to overwriting an already valid value.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The contention window is supposed to be a power of two minus one, i.e.
15, 31, 63, 127... minstrel_rate_init() forgets to subtract 1, so the
sequence becomes 15, 32, 66, 134...
Bug reported by Dan Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.
To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.
# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5
This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.
The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can just display this upon enabling mac80211 with an
'if MAC80211 != n' check.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All instances of file_operations should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly just simple conversions:
* ray_cs had bogus return of NET_TX_LOCKED but driver
was not using NETIF_F_LLTX
* hostap and ipw2x00 had some code that returned value
from a called function that also had to change to return netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the queued management work items are processed in
ieee80211_sta_work() an item could be removed. This could change the
anybusy from true to false, so we better check whether we can start a
new scan only after having processed the pending work first.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is taken down while a scan is
pending -- i.e. a scan request was accepted but
not yet acted upon due to other work being in
progress -- we currently do not properly cancel
that scan and end up getting stuck. Fix this by
doing better checks when an interface is taken
down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An integer overflow in the minstrel debug code prevented the
throughput to be displayed correctly. This patch fixes that,
by permutating operations like proposed by Pavel Roskin.
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mac80211's RX path some of the warnings that
warn about drivers passing invalid status values
leak the skb, fix that by refactoring the code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed that the throughput field of the minstrel_rate struct is never used,
so remove it.
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to the way the tasklets work in mac80211 there's
no need to ever disable them.
However, we need to clear the pending packets when
taking down the last interface because otherwise
the tx_pending_tasklet might be queued if the
driver mucks with the queues (which it shouldn't).
I've had a situation occasionally with ar9170 in
which ksoftirq was using 100% CPU time because
a disabled tasklet was scheduled, and I think that
was due to ar9170 receiving a packet while the
tasklet was disabled. That's strange and it really
should not do that for other reasons, but there's
no need to waste that much CPU time over it, it
should just warn instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since configure_filter can sleep now, any multicast
configuration needed to be postponed to a work struct.
This, however, lead to a problem that we could queue
the work, stop the device and then afterwards invoke
configure_filter which may lead to driver hangs and is
a bug. To fix this, we can just cancel the filter work
since it's unnecessary to do after stopping the hw.
Since there are various places that call drv_stop, and
two of them do very similar things, the code for them
can be put into a shared function at the same time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh config information element has changed significantly since draft 1.08
This patch brings it up to date.
Thanks to Sam Leffler and Rui Paulo for identifying this.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: fix alignment problem in scan request"
introduced a bug into the error path, because now
we allocate the entire scan request and not just
the channel list (the channel list is allocated
together with the scan request) -- on errors we
thus also need to free the entire scan request.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This expands on the current fwded_frames stat counter which should be equal to
the total of these two new counters. The new counters are called "fwded_mcast"
and "fwded_unicast".
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] net/mac80211/rc80211_pid_algo.o
net/mac80211/rc80211_pid_algo.c: In function ‘rate_control_pid_rate_init’:
net/mac80211/rc80211_pid_algo.c:304: warning: unused variable ‘si’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh uses the tx failure average to compute the (m)path metric. This used to
be done inside the rate control module. This patch breaks the dependency
between the mesh stack and the rate control algorithm. Mesh will now work
independently of the chosen rate control algorithm.
The mesh stack keeps a moving average of the average transmission losses for
each mesh peer station. If the fail average exceeds a certain threshold, the
peer link is marked as broken.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the fixed portion of plink confirm frames is 4 bytes longer than
the other plink_action frames. This path corrects an error in the length
adjustment done for these type of frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a PREQ frame is received giving us a fresher DSN than what we have, record
the new dsn and mark it as valid. This patch fixes a bug in the setting of the
MESH_PATH_DSN_VALID flag.
Also, minor fix to coding style on that file.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif. This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx(). This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents calling rcu_synchronize from within the tx path by moving the
table growth code to the mesh workqueue.
Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and
declare them static.
Also, re-enable mesh in Kconfig and update the configuration description.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh stack was enabling beaconing without specifying an interval. This
patch defines a default beaconing interval of 1s.
Incidentally, this fixes mesh beaconing in mac80211_hwsim devices.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change triggers a path discovery as soon as the link quality degrades
below a certain threshold. This results in a faster path recovery time than
by simply relying on the periodic path refresh mechanism to detect broken
links.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fail_avg value is used to compute the mesh metric, and was only being set
by the pid rate control module. This fixes the mesh path selection mechanism
for cards that use mistrel for rate control.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address. This was done to avoid interactions with widely
deployed lazy-WDS access points.
This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward. The
address fields used for group addressed frames is:
In 802.11 header
ToDS:0 FromDS:1
addr1: DA (broadcast/multicast address)
addr2: TA
addr3: Mesh SA
In address extension header:
addr4: SA (only present if frame was proxied)
Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On locally originated traffic, we refresh active paths after a timeout. The
decision to do this was using the wrong sign and therefore the refresh timer
was triggered for every frame.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, fix typo in comment.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's really easier to read if it's not indented
as much, so invert the condition and rearrange
the code so the smaller chunk is indented instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to mask the variable with 0xFFF0
since we ever only use it as a u16 and the lowest
four bits can't ever be non-zero. The compiler
cannot infer the latter, and therefore has to emit
code to do the masking.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When encryption is used, the number of bytes
sent to the peer increases by the IV and ICV.
This is accounted if software encryption is
used, but not if the devices does hardware
encryption. To make the numbers comparable,
never account for that overhead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The memory layout for scan requests was rather wrong,
we put the scan SSIDs before the channels which could
lead to the channel pointers being unaligned in memory.
It turns out that using a pointer to the channel array
isn't necessary anyway since we can embed a zero-length
array into the struct.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have a lot of frames to transmit at once, for
instance with fragmentation, it can be an optimisation
to only tell the DMA engine about them on the last
fragment/frame to avoid banging the IO too much. This
patch allows implementation such an optimisation by
telling the driver when more frames can be expected.
Currently, this is used by mac80211 only on fragmented
frames, but could also be used in the future on other
frames when the queue was full and there are multiple
frames pending.
Note that drivers need to be careful when using this
flag, they need to kick their DMA engines not just
when this flag is clear, but also when the queue gets
full so that progress can be made.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for userspace to be able to figure out whether
it obtained a consistent snapshot of data or not when
using netlink dumps, we need to have a generation number
in each dump message that indicates whether the list has
changed or not -- its value is arbitrary.
This patch adds such a number to all dumps, this needs
some mac80211 involvement to keep track of a generation
number to start with when adding/removing mesh paths or
stations.
The wiphy and netdev lists can be fully handled within
cfg80211, of course, but generation numbers need to be
stored there as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After being disassociated by the AP, mac80211 currently
reports this to cfg80211, and then goes to delete the
association. That's fine, but cfg80211 assumes that it's
still authenticated, however, mac80211 throws away all
state.
This fixes mac80211 to keep track of the authentication
in that case so that cfg80211 can request a deauth or
new association properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh is currently disabled on mac80211, its marked
as broken. This patch gets it to compile though,
to account for the mac80211 workqueue changes.
There was a simple typo in the patches for mesh
for the workqueue migration, but we never compile
tested it as we couldn't even select mesh as its
broken. Lets at least let it compile for those
interested in getting it fixed.
Reported-by: Pat Erley <pat-lkml@erley.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We splice skbs from the pending queue for a TID
onto the local pending queue when tearing down a
block ack request. This is not necessary unless we
actually have received a request to start a block ack
request (rate control, for example). If we never received
that request we should not be splicing the tid pending
queue as it would be null, causing a panic.
Not sure yet how exactly we allowed through a call when the
tid state does not have at least HT_ADDBA_REQUESTED_MSK set,
that will require some further review as it is not quite
obvious.
For more information see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=13922
This fixes this oops:
BUG: unable to handle kernel NULL pointer dereference at 00000030
IP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
*pdpt = 0000000002d1e001 *pde = 0000000000000000
Thread overran stack, or stack corrupted
Oops: 0000 [#1] SMP
last sysfs file: /sys/module/aes_generic/initstate
Modules linked in: <bleh>
Pid: 0, comm: swapper Not tainted (2.6.31-rc5-wl #2) Dell DV051
EIP: 0060:[<f8806c70>] EFLAGS: 00010292 CPU: 0
EIP is at ieee80211_agg_splice_packets+0x40/0xc0 [mac80211]
EAX: 00000030 EBX: 0000004c ECX: 00000003 EDX: 00000000
ESI: c1c98000 EDI: f745a1c0 EBP: c076be58 ESP: c076be38
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c076a000 task=c0709160 task.ti=c076a000)
Stack: <bleh2>
Call Trace:
[<f8806edb>] ? ieee80211_stop_tx_ba_cb+0xab/0x150 [mac80211]
[<f8802f1e>] ? ieee80211_tasklet_handler+0xce/0x110 [mac80211]
[<c04862ff>] ? net_rx_action+0xef/0x1d0
[<c0149378>] ? tasklet_action+0x58/0xc0
[<c014a0f2>] ? __do_softirq+0xc2/0x190
[<c018eb48>] ? handle_IRQ_event+0x58/0x140
[<c01205fe>] ? ack_apic_level+0x7e/0x270
[<c014a1fd>] ? do_softirq+0x3d/0x40
[<c014a345>] ? irq_exit+0x65/0x90
[<c010a6af>] ? do_IRQ+0x4f/0xc0
[<c014a35d>] ? irq_exit+0x7d/0x90
[<c011d547>] ? smp_apic_timer_interrupt+0x57/0x90
[<c01094a9>] ? common_interrupt+0x29/0x30
[<c010fd9e>] ? mwait_idle+0xbe/0x100
[<c0107e42>] ? cpu_idle+0x52/0x90
[<c054b1a5>] ? rest_init+0x55/0x60
[<c077492d>] ? start_kernel+0x315/0x37d
[<c07743ce>] ? unknown_bootoption+0x0/0x1f9
[<c0774099>] ? i386_start_kernel+0x79/0x81
Code: <bleh3>
EIP: [<f8806c70>] ieee80211_agg_splice_packets+0x40/0xc0 [mac80211] SS:ESP 0068:c076be38
CR2: 0000000000000030
Cc: stable@kernel.org
Testedy-by: Jack Lau <jackelectronics@hotmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is configured in the AP mode, the mac80211
implementation doesn't inform the driver to receive PS Poll frames.
It leads to inability to communicate with power-saving stations
reliably.
The FIF_CONTROL flag isn't passed by mac80211 to
ieee80211_ops.configure_filter when an interface is in the AP mode.
And it's ok, because we don't want to receive ACK frames and other
control ones, but only PS Poll ones.
This patch introduces the FIF_PSPOLL filter flag in addition to
FIF_CONTROL, which means for the driver "pass PS Poll frames".
This flag is passed to the driver:
A) When an interface is configured in the AP mode.
B) In all cases, when the FIF_CONTROL flag was passed earlier (in
addition to it).
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do a probe request every 30 seconds, and wait for probe response,
half a second This should lower the traffic that card sends, thus save
power Wainting longer for response makes probe more robust against
'slow' access points
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retry 5 times (chosen arbitary ), before assuming
that station is out of range.
Fixes frequent disassociations while connected to weak,
and sometimes even strong access points.
Signed-off-by: Maxim Levitky <maximlevitsky@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.
Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the recent MLME rework I did broke powersave
because the ps_sdata isn't assigned at the right time,
and the work item wasn't removed from the list before
calling ieee80211_recalc_ps(). To be more specific,
this broke the case where you'd enabled PS before
associating, either automatically or with iwconfig.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 workqueue exists to enable mac80211 and drivers
to queue their own work on a single threaded workqueue. mac80211
takes care to flush the workqueue during suspend but we never
really had requirements on drivers for how they should use
the workqueue in consideration for suspend.
We extend mac80211 to document how the mac80211 workqueue should
be used, how it should not be used and finally move raw access to
the workqueue to mac80211 only. Drivers and mac80211 use helpers
to queue work onto the mac80211 workqueue:
* ieee80211_queue_work()
* ieee80211_queue_delayed_work()
These helpers will now warn if mac80211 already completed its
suspend cycle and someone is trying to queue work. mac80211
flushes the mac80211 workqueue prior to suspend a few times,
but we haven't taken the care to ensure drivers won't add more
work after suspend. To help with this we add a warning when
someone tries to add work and mac80211 already completed the
suspend cycle.
Drivers should ensure they cancel any work or delayed work
in the mac80211 stop() callback.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse complains about a shadowed variable, which
we can just rename, and lots of stuff if the API
tracer is enabled, so kick out the tracer code in
a sparse run -- the macros just confuse it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When downing interfaces, it's a good idea to tell the driver to
stop sending beacons; that way the driver doesn't need special
code in ops->remove_interface() when it should already handle the
case in bss_info_changed().
This fixes a potential crash with at least ath5k since the vif
pointer will be nullified while beacon interrupts are still active.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported a problem that seems to be due to
software retry of already transmitted frames. It turns
out that we've never done that correctly, but due to
some recent changes it now crashes in the TX code. I've
added a comment in the patch that explains the problem
better and also points to possible solutions -- which
I can't implement right now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally! This is what you've all been waiting for!
This patch makes cfg80211 take care of wext emulation
_completely_ by itself, drivers that don't need things
cfg80211 doesn't do yet don't even need to be aware of
wireless extensions.
This means we can also clean up mac80211's and iwm's
Kconfig and make it possible to build them w/o wext
now!
RIP wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have handlers IWESSID for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have IWAP handlers for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now we implemented iwfreq for managed mode, we
needed to keep the implementations separate, but now
that we have all versions implemented we can combine
them and export just one handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enqueuing packets on the internal packet queue, we
need to ensure that we have a valid vif pointer since
that is required since the net namespace work. Add some
assertions to verify this, but also don't crash is for
some reason we don't end up with a vif pointer -- warn
and drop the packet in all these cases.
Since this code touches a number of hotpaths, it is
intended to be temporary, or maybe configurable in the
future, at least the bit that is in the path that gets
hit for every packet, ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an oops in ieee80211_scan_state_set_channel which was triggered
if the last scanned channel was skipped (for example due to regulatory
restrictions) by returning to the decision state after each skipped
channel.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel reported a warning, which quite obviously comes
from an oversight in the code handling deauth frames,
and which resulted in multiple follow-up warnings due
to this missing handling. This patch adds the missing
deauth handling (telling cfg80211 about it) and also
removes the follow-up warnings since they could happen
due to races even if nothing is wrong. I've explained
the races in the comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jan reported that his b43-based laptop hangs during suspend.
The problem turned out to be mac80211 asking the driver to
stop the hardware before removing interfaces, and interface
removal caused b43 to touch the hardware (while down, which
causes the hang).
This patch fixes mac80211 to do reorder these operations to
have them in the correct order -- first remove interfaces
and then stop the hardware. Some more code is necessary to
be able to do so in a race-free manner, in particular it is
necessary to not process frames received during quiescing.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13337.
Reported-by: Jan Scholz <scholz@fias.uni-frankfurt.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was caused by patch:
"mac80211: cooperate more with network namespaces"
The version of the patch applied doesn't match Johannes' latest:
http://johannes.sipsolutions.net/patches/kernel/all/LATEST/NNN-mac80211-netns.patch
The skb->cb virtual interface data wasn't being reset for
reuse so ath9k pooped out when trying to dereference the
private rate control info from the skb.
BUG: unable to handle kernel NULL pointer dereference
RIP: 0010:[<ffffffffa0258173>] ath_tx_rc_status+0x33/0x150 [ath9k]
<-- snip etc -->
Reported-by: Davide Pesavento <davidepesa@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were issuing probe requests to the associated AP on the wrong
band by having our beacon timer loss trigger while we are scanning.
When we would scan the timer could hit and force us to send a
probe request to the AP but with a chance we'd be on the wrong band.
This leads to finding no usable bitrate but we should not get so
far on the xmit path. We should not be trying to send these probe
request frames so prevent ieee80211_mgd_probe_ap() from sending
these.
As it turns out all callers of ieee80211_mgd_probe_ap() need this
check so we just move the scan check there. This means we can remove
the recenlty added check during ieee80211_sta_monitor_work().
Additionally we now fix a race condition added by the patch
"mac80211: do not monitor the connection while scanning" which
had the same check in ieee80211_sta_conn_mon_timer(). The race
happens because the timer routine *does* a valid check for
scanning but after it queues work into the mac80211 workqueue
the work callback can kick off with scanning enabled and cause
the same issue we were trying to avoid.
The more appropriate solution would be to disable the respective
timers during scan and re-enable them after scan but requires more
complex code and testing.
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a new MLME work is created, its timeout is initialised
to 0. This is wrong, it could then be thought of as having
an actual timeout in the future (time_is_after_jiffies() can
return true). Instead, it should be initialised to jiffies
so that it will run right away as soon as the mlme work is
executed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Luciano Roth Coelho <luciano.coelho@nokia.com>
Reported-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename scan_state to next_scan_state to better reflect
what it is used for.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us
that we are currently on a different channel for scanning and cannot
RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a
software scan but we might as well be on the operating channel to RX/TX.
While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL"
is set when leaving the operating channel and unset when coming back.
Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and
"SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we
need to leave the operating channel (send a nullfunc to the AP and stop
the queues) and enter it again (send a nullfunc to the AP and start the
queues again).
Enhance the scan state "SCAN_DECISION" to switch back to the operating
channel after each scanned channel. In the future it sould be simple
to enhance the decision state to scan as much channels in a row as the
qos latency allows us.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan state "decision" which is entered after
every completed scan operation and decides about the next steps.
At first the decision is in any case to scan the next channel.
This shouldn't introduce any functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of queueing the scan work again without delay just process the
next state immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the processing of each scan state into its own functions for better
readability. This patch does not introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This finally opens up the ability to put mac80211 devices
into different network namespaces. As long as you don't
have sysfs, that is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removal of the master netdev broke the mesh forwarding path. This patch
fixes it by using the new internal 'pending' queue.
As a result of this change, mesh forwarding no longer does the inefficient
802.11 -> 802.3 -> 802.11 conversion that was done before.
[Changes since v1]
Suggested by Johannes:
- Select queue before adding to mpath queue
- ieee80211_add_pending_skb -> ieee80211_add_pending_skbs
- Remove unnecessary header wme.h
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_xmit() cannot be called with tasklets enabled
because it is normally called from within a tasklet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following errors:
driver-trace.h:148:1: error: cannot size expression
driver-trace.h:148:1: error: cannot size expression
[...]
driver-trace.h:222:1: error: cannot size expression
driver-trace.h:71:1: error: incompatible types for operation (<)
driver-trace.h:71:1: left side has type void *<noident>
driver-trace.h:71:1: right side has type int
driver-trace.h:99:1: error: incompatible types for operation (<)
driver-trace.h:99:1: left side has type void *<noident>
driver-trace.h:99:1: right side has type int
driver-trace.h:148:1: error: incompatible types for operation (<)
driver-trace.h:148:1: left side has type void *<noident>
driver-trace.h:148:1: right side has type int
driver-trace.h:222:1: error: cannot size expression
driver-trace.h:248:1: error: incompatible types for operation (<)
driver-trace.h:248:1: left side has type void *<noident>
driver-trace.h:248:1: right side has type int
driver-trace.h:446:1: error: incompatible types for operation (<)
driver-trace.h:446:1: left side has type void *<noident>
driver-trace.h:446:1: right side has type int
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 constantly monitors the connection to the associated AP
in order to check if it is out of reach/dead.
This is absolutely fine most of the time.
Except when there is a scheduled scan for the whole neighborhood.
After all this path could trigger while scanning on different channel.
Or even worse: this AP probing triggers a WARN_ON in rate_lowest_index
when the scan code did a band transition!
( http://www.kerneloops.org/raw.php?rawid=449304 )
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we're associated we should be able to send data to
target sta. If we cannot we may be trying to use the incorrect
band to talk to the sta. Lets catch any such cases, warn, and
drop the frames to not invalidate assumptions being made on
rate control algorithms when they have a valid sta to
communicate with. Any such cases should be handled and fixed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "mac80211: monitor the connection" I forgot to
add code to cancel the new timers & work when the
interface is brought down, which isn't a problem
if you just bring it down, but _is_ a problem when
you destroy the interface. Correct this lapse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) there's a spin_lock() that needs to be spin_lock_bh()
2) action frames of size 24 might cause an out-of-bounds
memory access (for the 25th byte only, so no big deal)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent MLME rework I accidentally removed the connection
monitoring code. In order to add it back, this patch will add new
code to monitor both for beacon loss and for the connection actually
working, with possibly separate triggers.
When no unicast frames have been received from the AP for (currently)
two seconds, we will send the AP a probe request. Also, when we don't
see beacons from the AP for two seconds, we do the same (but those
times need not be the same due to the way the code is now written).
Additionally, clean up the parameters to the ieee80211_set_disassoc()
function that I need here, those are all useless except sdata.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have, sometimes, multiple things that want to
run but don't have their own timer. Introduce a
new function to mac80211's mlme run_again() that
makes sure that the timer will run again at the
_first_ needed time, use that function and also
properly reprogram the timer once it fired.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign next hop address to pending mesh frames once the path is resolved.
Regression. Frames transmitted when a mesh path was wating to be resolved were
being transmitted with an invalid Receiver Address.
[Changes since v1]
Suggested by Johannes:
- Improved frame_queue traversal
- Narower RCU scope
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 use the event tracing framework
to log all operations as given to the driver. This
will need to be extended with more information, but
as a start it should be good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_testmode_cmd can very well be static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For forwarded frames, we save the precursor address in addr1 in case it
needs to be used to send a Path Error. mesh_path_discard_frame,
however, was using addr2 instead of addr1 to send Path Error frames, so
correct that and also make the comment regarding this more clear.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The location of the 802.11 header is calculated incorrectly due to a
wrong placement of parentheses. Found by kmemcheck.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My kvm instance was complaining a lot about sleeping
in atomic contexts in the mesh code, and it turns out
that both mesh_path_add() and mpp_path_add() need to
be able to sleep (they even use synchronize_rcu()!).
I put in a might_sleep() to annotate that, but I see
no way, at least right now, of actually making sure
those functions are only called from process context
since they are both called during TX and RX and the
mesh code itself even calls them with rcu_read_lock()
"held".
Therefore, let's disable it completely for now.
It's possible that I'm only seeing this because the
hwsim's beaconing is broken and thus the peers aren't
discovered right away, but it is possible that this
happens even if beaconing is working, for a peer that
doesn't exist or so.
It should be possible to solve this by deferring the
freeing of the tables to call_rcu() instead of using
synchronize_rcu(), and also using atomic allocations,
but maybe it makes more sense to rework the code to
not call these from atomic contexts and defer more of
the work to the workqueue. Right now, I can't work on
either of those solutions though.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a lot of locking issues have crept into
the smarts of cfg80211, so e.g. scan completion can
race against a new scan, IBSS join can race against
leaving an IBSS, etc.
Introduce a new per-interface lock that protects
most of the per-interface data that we need to keep
track of, and sprinkle assertions about that lock
everywhere. Some things now need to be offloaded to
work structs so that we don't require being able to
sleep in functions the drivers call. The exception
to that are the MLME callbacks (rx_auth etc.) that
currently only mac80211 calls because it was easier
to do that there instead of in cfg80211, and future
drivers implementing those calls will, if they ever
exist, probably need to use a similar scheme like
mac80211 anyway...
In order to be able to handle _deauth and _disassoc
properly, introduce a cookie passed to it that will
determine locking requirements.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the mac80211 mlme cleanup, we can require that
the MLME functions in cfg80211 can sleep. This will
simplify future work in cfg80211 a lot.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new key work for cfg80211 will only give us the WEP
key for shared auth to do that authentication, and not
via the regular key settings, so we need to be able to
encrypt a single frame in software, and that without a
key struct. Thus, refactor the WEP code to not require
a key structure but use the key, len and idx directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sit tight. This shakes up the world as you know
it. Let go of your spaghetti tongs, they will no
longer be required, the horrible statemachine in
net/mac80211/mlme.c is no more...
With the cfg80211 SME mac80211 now has much less
to keep track of, but, on the other hand, for FT
it needs to be able to keep track of at least one
authentication being in progress while associated.
So convert from a single state machine to having
small ones for all the different things we need to
do. For real FT it will still need work wrt. PS,
but this should be a good step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ap_capab and last_probe struct members are unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we don't really know that well in the kernel,
let's let the SME control whether it wants to use
reassociation or not, by allowing it to give the
previous BSSID in the associate() parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's software scan implementation uses a passive dwell time of
(HZ / 5) which means we stay 200ms on each passive channel. Compared
to iwlwifi's hw scan and the old ipw* drivers which use values around
120ms this is quite long.
Reducing the passive dwell time from 200ms to 125ms should save us
something around a second on cards capable of 11a and we should still be
able to catch beacons from most access points (assuming a ~100ms beacon
interval).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function from mac80211 seems generally useful, and
I will need it in cfg80211 soon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 now always controlled by an external SME,
a lot of code is dead -- SSID, BSSID, channel selection
is always done externally, etc. Additionally, rename
IEEE80211_STA_TKIP_WEP_USED to IEEE80211_STA_DISABLE_11N
and clean up the code a bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The automatic auth algorithm issue is now solved in
cfg80211, so mac80211 no longer needs code to try
different algorithms -- just using whatever cfg80211
asked for is good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IEEE80211_STA_TKIP_WEP_USED flag is used internally to
disable HT when WEP or TKIP are used. Now that cfg80211 is
giving us the required information, we can set the flag
appropriately again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By dropping the noise reporting, we can implement
wireless stats in cfg80211. We also make the
handler return NULL if we have no information,
which is possible thanks to the recent wext change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, let's implement that using a very hackish way:
simply mirror the wext API in the cfg80211 API. This
will have to be changed later when we implement proper
bitrate API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements siocsiwap/giwap for WDS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just on/off and timeout, and with a hacky cfg80211 method
until we figure out what we want, though this is probably
sufficient as we want to use pm_qos for wifi everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the cfg80211 connect/disconnect API.
The goal here is to run the AUTH and ASSOC steps in one call.
This is needed for some fullmac cards that run both steps
directly from the target, after the host driver sends a
connect command.
Additionally, all the new crypto parameters for connect()
are now also valid for associate() -- although associate
requires the IEs to be used, the information can be useful
for drivers and should be given.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_scan_results function hasn't existed for a
long time now, so its declaration should be removed as
well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a new NL80211_CMD_TESTMODE for testing
and calibration use with nl80211. There's no multiplexing
like like iwpriv had, and the command is not available by
default, it needs to be explicitly enabled in Kconfig and
shouldn't be enabled in most kernels.
The command requires a wiphy index or interface index to
identify the device to operate on, and the new TESTDATA
attribute. There also is API for sending replies to the
command, and testmode multicast messages (on a testmode
multicast group).
I've also updated mac80211 to be able to pass through the
command to the driver, since it itself doesn't implement
the testmode command.
Additionally, to give people an idea of how to use the
command, I've added a little code to hwsim that makes use
of the new command to set the powersave mode, this is
currently done via debugfs and should remain there, and
the testmode command only serves as an example of how to
use this best -- with nested netlink attributes in the
TESTDATA attribute. A hwsim testmode tool can be found at
http://git.sipsolutions.net/hwsim.git/. This tool is BSD
licensed so people can easily use it as a basis for their
own internal fabrication and validation tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the auth algorithm is rejected, but we don't have
another one to try, we will eventually retry but that
isn't useful -- we'll then do it again and again until
we eventually give up. Instead, we should let the SME
know and go into disabled state. The same applies for
situations where the AP rejects with any other status
code.
Additionally, when trying the next auth algorithm, we
should reset the auth_tries so that just a single lost
frame doesn't lead to us giving up on the third auth
algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The key todo lock can be taken from different locks
that require it to be _bh to avoid lock inversion
due to (soft)irqs.
This should fix the two problems reported by Bob and
Gabor:
http://mid.gmane.org/20090619113049.GB18956@hash.localnethttp://mid.gmane.org/4A3FA376.8020307@openwrt.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having mac80211 do it itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had code for a number of files, that we didn't publish
in debugfs, fix that. Also make the agg_status file layout
more readable and add more information to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg