Background: ExpressKey Remotes communicate their events via usb dongle.
Each dongle can hold up to 5 pairings at one time and one EKR (identified
by its serial number) can unfortunately be paired with its dongle
more than once. The pairing takes place in a round-robin fashion.
Input devices are only created once per EKR, when a new serial number
is seen in the list of pairings. However, if a device is created for
a "higher" paring index and subsequently a second pairing occurs at a
lower pairing index, unpairing the remote with that serial number from
any pairing index will currently cause a driver crash. This occurs
infrequently, as two remotes are necessary to trigger this bug and most
users have only one remote.
As an illustration, to trigger the bug you need to have two remotes,
and pair them in this order:
1. slot 0 -> remote 1 (input device created for remote 1)
2. slot 1 -> remote 1 (duplicate pairing - no device created)
3. slot 2 -> remote 1 (duplicate pairing - no device created)
4. slot 3 -> remote 1 (duplicate pairing - no device created)
5. slot 4 -> remote 2 (input device created for remote 2)
6. slot 0 -> remote 2 (1 destroyed and recreated at slot 1)
7. slot 1 -> remote 2 (1 destroyed and recreated at slot 2)
8. slot 2 -> remote 2 (1 destroyed and recreated at slot 3)
9. slot 3 -> remote 2 (1 destroyed and not recreated)
10. slot 4 -> remote 2 (2 was already in this slot so no changes)
11. slot 0 -> remote 1 (The current code sees remote 2 was paired over in
one of the dongle slots it occupied and attempts
to remove all information about remote 2 [1]. It
calls wacom_remote_destroy_one for remote 2, but
the destroy function assumes the lowest index is
where the remote's input device was created. The
code "cleans up" the other remote 2 pairings
including the one which the input device was based
on, assuming they were were just duplicate
pairings. However, the cleanup doesn't call the
devres release function for the input device that
was created in slot 4).
This issue is fixed by this commit.
[1] Remote 2 should subsequently be re-created on the next packet from the
EKR at the lowest numbered slot that it occupies (here slot 1).
Fixes: f9036bd436 ("HID: wacom: EKR: use devres groups to manage resources")
Cc: stable <stable@vger.kernel.org> #4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Userspace expects to receive tool type and serial number information
for the active pen in the very first kernel report, if such data is
supported by the hardware. While this expectation is not an issue for
EMR devices, AES sensors will often send several packets worth of in-
range data before relaying type/serial data to the kernel. Sending this
data "late" can result in proximity-tracking issues by xf86-input-wacom,
or an inability to distinguish different pens by input-wacom.
Options for dealing with this situation include ignoring reports from
the tablet until we get the necessary data, or using the information
from the last-seen pen instead of the (eventual) real data. Neither
option is particularly attractive: the former results in truncated
strokes and the latter causes issues with switching between pens.
This commit instead opts to queue up events with missing information
until we receive a report which contains it. At that point, we can
update the driver's state variables (id[0] and serial[0]) and replay
the queued events.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- High resolution mode for DEll canvas support, from Benjamin Tissoires
- A lot of improvements to pen handling in the Wacom driver, from Jason Gerecke
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dell Canvas exports 2 collections for the Pen part. The only
difference between the 2 is that the default one has half the resolution
of the second one.
The Windows driver switches the tablet into the second mode, so we should
behave the same.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom_get_hdev_data function is used to find and return a reference to
the "other half" of a Wacom device (i.e., the touch device associated with
a pen, or vice-versa). To ensure these references are properly accounted
for, the function is supposed to automatically increment the refcount before
returning. This was not done, however, for devices which have pen & touch
on different interfaces of the same USB device. This can lead to a WARNING
("refcount_t: underflow; use-after-free") when removing the module or device
as we call kref_put() more times than kref_get(). Triggering an "actual" use-
after-free would be difficult since both devices will disappear nearly-
simultaneously. To silence this warning and prevent the potential error, we
need to increment the refcount for all cases within wacom_get_hdev_data.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a50aac7193 introduces 'led.groups' and adds EKR support
for these groups. However, unlike the other devices with LEDs,
the EKR's LEDs are read-only and we shouldn't attempt to control
them in wacom_led_control().
See bug: https://sourceforge.net/p/linuxwacom/bugs/342/
Fixes: a50aac7193 ("HID: wacom: leds: dynamically allocate LED groups")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'wacom_update_name' function is responsible for producing names for
the input device nodes based on the hardware device name. Commit f2209d4
added the ability to strip off prefixes like "Wacom Co.,Ltd." where the
prefix was immediately (and redundantly) followed by "Wacom". The
2nd-generation Intuos Pro 2 has such a prefix, but with a small error
(the period and comma are swapped) that prevents the existing code from
matching it. We're loath to extend the number of cases out endlessly and
so instead try to be smarter about name generation.
We observe that the cause of the redundant prefixes is HID combining the
manufacturer and product strings of USB devices together. By using the
original product name (with "Wacom" prefixed, if it does not already
exist in the string) we can bypass the gyrations to find and remove
redundant prefixes. Other devices either don't have a manufacturer string
that needs to be removed (Bluetooth, uhid) or should have their name
generated from scratch (I2C).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Variable mode in method wacom_show_remote_mode() is defined as u8, thus
statement (mode >= 0) is always true and should be removed, simplifying
the logic.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At the moment, our driver relies on 'wacom_battery_get_property()' to
determine the most likely battery state (e.g charging, discharging, or
full) based on the information available. It is not always possible
for the function to properly determine this, however. For instance,
whenever an AES pen leaves proximity the battery state becomes
indeterminite. This commit adds the ability to provide it with explict
state information if desired. Whenever explicit state is not required
(the majority of circumstances), WACOM_POWER_SUPPLY_STATUS_AUTO can
be used in its place.
Three uses of explicit battery status are added: two wireless disconnect
paths and the AES case mentioned above.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit a544c619a5 ("HID: wacom: do not attempt to switch mode
while in probe") introduces delayed work for querying (setting the
mode) on all tablets. Bamboo Touch (056a:00d0) has a ghost
interface which claims to be a pen device. Though this device can
be removed, we have to set the mode on the ghost pen interface
before we remove it. After the aforementioned delay was introduced
the device was being removed before the mode setting could be
executed.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A previous commit (below) adds a check for already probed interfaces to
Wacom's matching heuristic. Unfortunately this causes the Bamboo Pen
(CTL-460) to match itself to its 'ghost' touch interface. After
subsequent changes to the driver this match to the ghost causes the
kernel to crash. This patch avoids calling wacom_add_shared_data()
for the BAMBOO_PEN's ghost touch interface.
Fixes: 41372d5d40 ("HID: wacom: Augment 'oVid' and 'oPid' with heuristics for HID_GENERIC")
Cc: stable <stable@vger.kernel.org> # 4.9
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 5b779fc introduces the manual release of resources in wacom_remove() as
an addition to the driver's use of devm. The EKR resources can only be
released through wacom_remote_destroy_one() so we skip the manual release for
it.
Fixes: 5b779fc ("HID: wacom: release the resources before leaving despite devm")
Signed-off-by: Aaron Armstrong Skomra <skomra@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro has a softkey to turn touch on/off. Since it is
a softkey, hardware/firmware still reports touch events no matter
what state the softkey is. We need to ignore touch events when
the key is in off mode.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom Cintiq Pro added a touch key to switch the tablet between
display and opaque mode. This patch informs the change by removing
the old devices and creating new ones with proper properties.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Tested-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the LEDs around the mode switch to the generic code path in
support of the second generation Intuos Pro.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The second generation Intuos Pro is the first device in the generic codepath
which has a touchswitch. We utilize a flag in wacom_shared in order to report
this switch event received from the pad on the touch input.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add vendor defined touch to support the second generation Intuos Pro.
Previously all generic Wacom devices used true HID to report their touch.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to its USB interface, the second-generation Intuos Pro
includes a Bluetooth radio that offers two pairing interfaces: classic
and low-energy. The classic interface functions just like the earlier
Bluetooth-enabled Intuos4 and Graphire4 tablets, appearing as a HID device
that our driver can work with. The low-energy interface is intented to
be used by userspace applications that make use of its paper-to-digital
capabilities.
Despite the USB interface using Wacom's new vendor-defined HID usages,
the Bluetooth interface provides us with useless black-box "blob"
report descriptors like past devices. We thus have to explicitly add
support for the PIDs and reports used.
These devices pack a /lot/ of information into a single Bluetooth
input report. Each report contains up to seven snapshots of the pen
state, four snapshots of the touch state (of five touches each), pad
state, and battery data. Thankfully this isn't too hard for the driver
to report -- it just takes a fair amount of code to extract!
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Centralize our definition of report IDs by moving those for device commands
into wacom_wac.h alongside those for input reports.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Intuos Pro seems to not like when we set the features right after
being powered up. Instead of waiting during probe, we can schedule the
switch mode and LED control in a deferred worker so that we don't have the
5 secs of delay from USB when the device is not accessible.
The USB timeout delays were really a pain because if you happen to unplug
the tablet while it is still waiting, you are just adding 5 second timeouts
to the USB stack. Which means that a new plug of the same tablet will also
gets delayed, and will also attempt to access the hardware while in
.probe(). So the tablet doesn't appear in the dmesg, the user unplug/replug
it to make it appearing... and so on so forth.
Really, this is for the best :)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When the LED class gets removed, it actually tries to reset the LED.
However, the device being disconnected, the set_report fails.
Previously, the attempt to cut lose this last event was through unsetting
the HID drvdata, but it was not working properly. Simply reset the LED
groups to NULL makes a more efficient solution.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the general case, the resources are properly released by devm without
needing to do anything. However, when unplugging the wireless receiver,
the kernel segfaults from time to time while calling devres_release_all().
I think in that case the resources attempt to access hid_get_drvdata(hdev)
which has been set to null while leaving wacom_remove().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 345857b ("HID: wacom: generic: Add support for sensor offsets") included
a change to the operation and location of the call to 'wacom_add_shared_data'
in 'wacom_parse_and_register'. The modifications included moving it higher up
so that it would occur before the call to 'wacom_retrieve_hid_descriptor'. This
was done to prevent a crash that would have occured when the report containing
tablet offsets was fed into the driver with 'wacom_hid_report_raw_event'
(specifically: the various 'wacom_wac_*_report' functions were written with the
assumption that they would only be called once tablet setup had completed;
'wacom_wac_pen_report' in particular dereferences 'shared' which wasn't yet
allocated).
Moving the call to 'wacom_add_shared_data' effectively prevented the crash but
also broke the sibiling detection code which assumes that the HID descriptor
has been read and the various device_type flags set.
To fix this situation, we restore the original 'wacom_add_shared_data'
operation and location and instead implement an alternative change that can
also prevent the crash. Specifically, we notice that the report functions
mentioned above expect to be called only for input reports. By adding a check,
we can prevent feature reports (such as the offset report) from
causing trouble.
Fixes: 345857bb49 ("HID: wacom: generic: Add support for sensor offsets")
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Local "#define DRIVER_LICENSE" obfuscates which license is used
in MODULE_LICENSE(). "fgrep -R MODULE_LICENSE" is more informative
when the string is hard coded in MODULE_LICENSE.
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many of Wacom's display tablets include an "outbound" area where pen
digitizing is possible but outside of the display area. To accommodate
such sensors in the HID_GENERIC codepath, we add support for the
necessary vendor-defined HID feature usages and adjust the min/max
values of the X and Y axes accordingly, similar to what is done in
the non-generic codepath.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Wacom's new "MobileStudio Pro" tablets are the first devices in their
branded product line-up to include a usable HID descriptor for the pen
interface. Like prior branded products, the device can operate in one
of two modes: 'Standard HID', and 'Wacom Custom HID'. Although the
first mode is usable by the HID_GENERIC codepath as-is (huzzah!), it is
subject to some restrictions -- most notably pressure being limited
to 2048 levels instead of 8192. To ensure tablets that include support
for Custom HID mode work optimally, we add support for its usages and
switch the device to Custom HID mode if possible.
The usages defined for Custom HID mode are often numerically similar to
their standard HID equivalents, allowing us to write a simple translation
function that takes arbitrary HID usages as input and which returns
the corresponding standard HID usage as output (if one exists). Switching
on this translated usage instead of the actual usage allows the existing
cases to apply to both modes of operation without having to explicitly
define every Custom HID usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The product name received from the string descriptor in the new MobileStudio
Pro line of tablets begins with "Wacom", which leads to unnecessary visual
noise in the device name when appended to the vendor name which also includes
"Wacom". Look for and fix cases like this.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ISDv4 devices have long supported reporting data from each of two barrel
switches, but HID_DG_BARRELSWITCH2 itself was only recently standardized.
Prior to its adoption, ISDv4 devices would associate the bit indicating
the state of the second barrel switch with the "Undefined" 0x000D0000
usage. Although most such devices have explicit support, a few use the
HID_GENERIC codepath which ignores the "Undefined" usage.
This patch adds code which detects the presence of a pre-standard second
barrel switch and corrects the usage value so that the HID_GENERIC code
will declare its presence and report its state.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Our loose use of "pen" and "digitizer" in the naming of several of our
vendor-defined usages may be a source of confusion given that the terms
have specific meaning within the HID specification. "Pen" specifically
refers to "an integrated display that allows the use of a stylus" (e.g.
something like a tablet PC or Cintiq) wheras "Digitizer" is a better
fit for opaque tablets like an Intuos.
While we're at it, go ahead and rename the definitions to make them more
distinct and better match up with the convention used by HID (e.g. the use
of '_UP_' for usage pages) and make them more distinct.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The 'oVid' and 'oPid' variables used by wacom_are_sibling are a hacky
solution to the problem of the driver historically having few good
heuristics to use in determining if two devices should be considered
siblings or not. While it works well enough for explicitly supported
devices, it offers no help for HID_GENERIC devices. Now that we have
a bit more information (e.g. direct/indirect) available to us though,
we should make use of it it to improve the pairing of such devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of displaying a generic "tablet", now g-c-c shows a pretty
"Wacom Intuos Pro S (WL)".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like upowerd is ignoring this since October 2013, so there is
no need to keep this around in the kernel.
And as mentioned in 8aaa592 (linux: Ignore ACs coming from devices) in
the upower tree, "We already have enough information on the device
battery".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When upowerd detects a new device, it tries to map this new device to
an input to guess its kind. It works OK for wired tablets when the
wireless module and its battery are attached, but not so well when
connected over wireless.
In that case, the battery is attached to the wireless HID node, not
the Pen or Pad HID node. So there is no input node as a parent of the
reported battery, which means it will be showed as a computer battery
in gnome-control-center.
If we set the power supply type to USB, upowerd has a heuristic that
detects "wacom_" in the name of the power_supply, and set the type to
tablet. So it's now clear that the reported battery of from a tablet.
(see https://cgit.freedesktop.org/upower/tree/src/linux/up-device-supply.c)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The EKR switches the LED directly, and there is no point in having
userspace handling the switch it self when it's easy enough to do
in the kernel.
The other benefit is that now userspace does not need to have root access
to the LED but need only to read them with user privileges.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a bug (?) in devm_led_classdev_register() in which its increments
the refcount of the parent. If the parent is an input device, that means
the ref count never reaches 0 when devm_input_device_release() gets called.
This means that the LEDs and all the devres resources attached to the
input device are not released.
Manually force the release of the group so that the leds are released once
we are done using them.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The now obsolete sysfs files for LEDs and EKRemote are kept for backward
compatibility.
Both the EKR (read-only) and the regular Cintiqs and Intuos are now
sharing the same led API.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or Gnome complains about an empty battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Previously, all the remotes attached to the same receiver would share the
same power_supply. That's not good as the remotes will constantly change
the battery information according to their own state.
To have something generic enough, we introduce struct wacom_battery
which regroups all the information we need for a battery.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres, we can now afford to create more than one input node
without having to overload the remove/failure paths. Having one input
node per remote is something which should have been implemented from start
but the probability of having users with several remotes is quite low.
Anyway, still, better looking at the future and implement things properly.
Remote input nodes will be freed/unregistered magically as they are
created in the devres group &remote->remotes[index].
We need to open the hid node now that the remotes are dynamically
allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No functional changes, just a prep patch for the one after.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This will be useful when each remote will be assigned its own input device.
We won't need to unregister each input and sysfs and other elements one
at a time.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wacom_remote_create_attr_group() and wacom_remote_destroy_attr_group()
functions were both allocating/destroying the sysfs groups but also
initializing the parameters for the remotes. Have proper functions
that can be called and extended.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Thanks to devres management, we don't need to remember a lot of failure
path. One or two is enough.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If we want to have one input device per remote, it's better to have our
own struct wacom_remote which is dynamically allocated.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_remote_status_irq() sends information of addition/removal of EKR.
We want to allocate one input node per remote, so better having this
in a separate worker, not handled in the IRQ directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We need to add an action to ensure wacom->led.groups is null when
wacom_led_control() gets called after the resources has been freed.
This also prevents to send a LED command when there is no support
from the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wacom_release_shared_data() and wacom_remove_shared_data() are moved up
so they can be referenced in wacom_add_shared_data().
There is no point in explicitly setting wacom_wac1->shared->type to 0 in
wacom_wireless_work() (plus this would give an oops).
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We started switching the driver to devres, so we should use it as much
as possible.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Aaron Armstrong Skomra