For a subtractive decode bridge, we previously added and printed all
resources of the primary bus, even if they were not valid. In the example
below, the bridge 00:1c.3 has no windows enabled, so there are no valid
resources on bus 02. But since 02:00.0 is subtractive decode bridge, we
add and print all those invalid resources, which don't really make sense:
pci 0000:00:1c.3: PCI bridge to [bus 02-03]
pci 0000:02:00.0: PCI bridge to [bus 03] (subtractive decode)
pci 0000:02:00.0: bridge window [??? 0x00000000 flags 0x0] (subtractive decode)
Add and print the subtractively-decoded resources only if they are valid.
There's an example in the dmesg log attached to the bugzilla below (but
this patch doesn't fix the bug reported there).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=73141
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the console is a PCI device, and we try to print to it while its
decoding is disabled, the system will hang. This particular printk hasn't
caused a problem yet, but it could, so this fixes it.
See also 0ff9514b57 ("PCI: Don't print anything while decoding is
disabled").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If a BAR is above 4GB and our dma_addr_t is too small, don't clear the BAR
to zero: that doesn't disable the BAR, and it makes it more likely that the
BAR will conflict with things if we turn on the memory enable bit (as we
will at "out:" if the device was already enabled at the handoff).
We should also print the BAR info and its original size so we can follow
the process when we try to assign space to it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If dma_addr_t is too small to represent the BAR value,
pcibios_bus_to_resource() will fail, so just remember the BAR size directly
in the resource. The resource is already marked UNSET, so we know the
address isn't valid anyway.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We can only handle BARs above 4GB if dma_addr_t (not resource_size_t) is 64
bits wide. If we have a 64-bit resource_size_t and a 32-bit dma_addr_t,
we can't deal with BARs above 4GB.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We can only handle BARs larger than 4GB if both dma_addr_t and
resource_size_t are 64 bits wide. If dma_addr_t is 32 bits, we can't
represent all the bus addresses, and if resource_size_t is 32 bits, we
can't represent all the CPU addresses.
Previously we cleared res->flags (at "fail:") for resources that were too
large. That means we think the BAR doesn't exist at all, which in turn
means that we could enable the device even though we can't keep track of
where the BAR is and we can't make sure it doesn't overlap something else.
This preserves the type flags (MEM/IO) so we can keep from enabling the
device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove pcibios_add_platform_entries(). Architecture-specific attributes
can be achieved by setting pdev->dev.groups.
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INTx masking does not work on this device. To see this, configure the
network device UP on an active network, note that the interrupt count
continues to increment for the device in /proc/interrupts. Use setpci to
set the PCI_COMMAND_INTX_DISABLE bit in the PCI_COMMAND register. As
expected, the interrupt count ceases to increment. However, reading the
PCI_STATUS_INTERRUPT bit of the PCI_STATUS register does not indicate that
interrupts are pending and clearing PCI_COMMAND_INTX_DISABLE in the
PCI_COMMAND register does not allow the device to continue operation.
This does not affect operation of the host r8169 driver, but it does
prevent the device from being functional when assigned to a VM, such as
with QEMU and VFIO. The guest driver successfully probes the device, but
there is no traffic. Mark INTx masking as broken, allowing the more
restrictive APIC masking to be used instead.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
No functional change, just cleaned up a bit.
This does not replace the requirement to move x86 to irq domains, but
it limits the mess to some degree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: x86@kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20140507154335.452206351@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When a new device is added below a hotplug bridge, the bridge's secondary
bus speed and the device's bus speed must match. The shpchp driver
previously checked the bridge's *primary* bus speed, not the secondary bus
speed.
This caused hot-add errors like:
shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch
Check the secondary bus speed instead.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251
Fixes: 3749c51ac6 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
CC: stable@vger.kernel.org # v2.6.34+
change made to resolve following checkpatch message:
drivers/pci/pci.c:109: ERROR: "foo* bar" should be "foo *bar"
branch: Linux 3.14-rc8
Signed-off-by: Ryan Desfosses <ryan@desfo.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- pci
- fix off-by-one for mbus window size
- split BARs into multiple mbus windows when needed
- mbus
- avoid setting undefined window size
- allow several windows with the same target/attr
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=b3o7
-----END PGP SIGNATURE-----
Merge tag 'mvebu-mbus_pci-fixes-3.15' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper:
mvebu drivers (mbus and pci) fixes for v3.15
- pci
- fix off-by-one for mbus window size
- split BARs into multiple mbus windows when needed
- mbus
- avoid setting undefined window size
- allow several windows with the same target/attr
* tag 'mvebu-mbus_pci-fixes-3.15' of git://git.infradead.org/linux-mvebu:
PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
bus: mvebu-mbus: allow several windows with the same target/attribute
bus: mvebu-mbus: Avoid setting an undefined window size
PCI: mvebu: fix off-by-one in the computed size of the mbus windows
Signed-off-by: Olof Johansson <olof@lixom.net>
There are no users of pci_enable_msi_block() function left. Obsolete it in
favor of pci_enable_msi_range() and pci_enable_msi_exact() functions.
Previously, we called arch_setup_msi_irqs() once, requesting the same
vector count we passed to arch_msi_check_device(). Now we may call it
several times: if it returns failure, we may retry and request fewer
vectors.
We don't keep track of the vector count we initially passed to
arch_msi_check_device(). We only keep track of the number of vectors
successfully set up by arch_setup_msi_irqs(), and this is what we use to
clean things up when disabling MSI. Therefore, we assume that
arch_msi_check_device() does nothing that will have to be cleaned up later.
[bhelgaas: changelog]
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the devspec OF attribute to PCI common code's set of device attributes
since it's not architecture dependent. As a side effect microblaze and
powerpc no longer need to use pcibios_add_platform_entries().
[bhelgaas: fold in #include for compile error]
Link: https://lkml.kernel.org/r/alpine.LFD.2.11.1404141101500.1529@denkbrett
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* pci/hotplug:
PCI: rphahp: Fix endianess issues
PCI: Allow hotplug service drivers to operate in polling mode
PCI: pciehp: Acknowledge spurious "cmd completed" event
PCI: pciehp: Use PCI_EXP_SLTCAP_PSN define
PCI: hotplug: Remove unnecessary "dev->bus" test
* pci/msi:
GenWQE: Use pci_enable_msi_exact() instead of pci_enable_msi_block()
PCI/MSI: Simplify populate_msi_sysfs()
PCI/portdrv: Use pci_enable_msix_exact() instead of pci_enable_msix()
* pci/virtualization:
PCI: Add Patsburg (X79) to Intel PCH root port ACS quirk
* pci/misc:
PCI: Fix use of uninitialized MPS value
PCI: Remove dead code
MAINTAINERS: Add arch/x86/kernel/quirks.c to PCI file patterns
PCI: Remove unnecessary __ref annotations
PCI: Fail new_id for vendor/device values already built into driver
PCI: Add new ID for Intel GPU "spurious interrupt" quirk
PCI: Update my email address
PCI: Fix incorrect vgaarb conditional in WARN_ON()
PCI: Use designated initialization in PCI_VDEVICE
PCI: Remove old serial device IDs
PCI: Remove unnecessary includes of <linux/init.h>
powerpc/PCI: Fix NULL dereference in sys_pciconfig_iobase() list traversal
If "pcie_bus_config == PCIE_BUS_PERFORMANCE", we don't initialize "smpss",
so we pass a pointer to garbage into pcie_bus_configure_set(), where we
compute "mps" based on the garbage. We then pass the garbage "mps" to
pcie_write_mps(), which ignores it in the PCIE_BUS_PERFORMANCE case.
Coverity isn't smart enough to deduce that we ignore the garbage (it's a
lot to expect from a human, too), so initialize "smpss" to a safe value in
all cases.
Found by Coverity (CID 146454).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some PCI functions used to be marked __devinit. When CONFIG_HOTPLUG was
not set, these functions were discarded after boot. A few callers of these
__devinit functions were marked __ref to indicate that they could safely
call the __devinit functions even though the callers were not __devinit.
But CONFIG_HOTPLUG and __devinit are now gone, and the need for the __ref
annotations is also gone, so remove them. Relevant historical commits:
54b956b903 Remove __dev* markings from init.h
a8e4b9c101 PCI: add generic pci_hp_add_bridge()
0ab2b57f8d PCI: fix section mismatch warning in pci_scan_child_bus
451124a7cc PCI: fix 4x section mismatch warnings
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
While using the sysfs new_id interface, the user can unintentionally feed
incorrect values if the driver static table has a matching entry. This is
possible since only the device and vendor fields are mandatory and the rest
are optional. As a result, store_new_id() will fill in default values that
are then passed on to the driver and can have unintended consequences.
As an example, consider the ixgbe driver and the 82599EB network card:
echo "8086 10fb" > /sys/bus/pci/drivers/ixgbe/new_id
This will pass a pci_device_id with driver_data = 0 to ixgbe_probe(), which
uses that zero to index a table of card operations. The zeroth entry of
the table does *not* correspond to the 82599 operations.
This change returns an error if the user attempts to add a dynid for a
vendor/device combination for which a static entry already exists.
However, if the user intentionally wants a different set of values, she
must provide all the 7 fields and that will be accepted.
[bhelgaas: drop KVM text since the problem isn't KVM-specific]
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Fix the following build warning that happens when building
multi_v7_defconfig with CONFIG_ARM_LPAE=y:
drivers/pci/host/pci-mvebu.c:334:5: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'phys_addr_t' [-Wformat=]
Fix the warning by using '%pa' to printing 'phys_addr_t' type. While at
it, also use the more standard notation [mem 0x-0x] for memory region.
[bhelgaas: make end address inclusive, remove extra spaces]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Serialization of configuration accesses is provided by 'pci_lock' in
drivers/pci/access.c thus making the driver's 'conf_lock' superfluous.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.
It turned out that the new CPU also featured a new GPU with a different PCI
ID.
Add this PCI ID to the quirk table. Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.
[bhelgaas: add f67fd55fa9 reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.4+
The problem was initially reported by Wendy who tried pass through
IPR adapter, which was connected to PHB root port directly, to KVM
based guest. When doing that, pci_reset_bridge_secondary_bus() was
called by VFIO driver and linkDown was detected by the root port.
That caused all PEs to be frozen.
The patch fixes the issue by routing the reset for the secondary bus
of root port to underly firmware. For that, one more weak function
pci_reset_secondary_bus() is introduced so that the individual platforms
can override that and do specific reset for bridge's secondary bus.
Reported-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Numerical values stored in the device tree are encoded in Big Endian and
should be byte swapped when running in Little Endian.
The RPA hotplug module should convert those values as well.
Note that in rpaphp_get_drc_props(), the comparison between indexes[i+1]
and *index is done using the BE values (whatever is the current endianess).
This doesn't matter since we are checking for equality here. This way only
the returned value is byte swapped.
RPA also made RTAS calls which implies BE values to be used. According to
the patch done in RTAS (http://patchwork.ozlabs.org/patch/336865), no
additional conversion is required in RPA.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
3448a19da4 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true. Replace with logical AND.
Found by Coverity (CID 142811).
Fixes: 3448a19da4 "vgaarb: use bridges to control VGA routing where possible"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Airlie <airlied@redhat.com>
Today the PCIe port bus driver disables the Hot-plug service if the port
device does not have the capability to generate interrupts. However, a
user must be able to use the "pciehp_poll_mode" parameter to use the pciehp
in polling method in such a case. Today it is not possible.
This patch allows a hotplug service driver to decide whether or not it
would like to continue in the absence of interrupts.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of a spurious "cmd completed", pcie_write_cmd() does not clear it,
but yet expects more "cmd completed" events to be generated. This does not
happen because the previous (spurious) event has not been acknowledged.
Fix that.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
MBus windows are used on Marvell platforms to map certain peripherals
in the physical address space. In the PCIe context, MBus windows are
needed to map PCIe I/O and memory regions in the physical address.
However, those MBus windows can only have power of two sizes, while
PCIe BAR do not necessarily guarantee this. For this reason, the
current pci-mvebu breaks on platforms where PCIe devices have BARs
that don't sum up to a power of two size at the emulated bridge level.
This commit fixes this by allowing the pci-mvebu driver to create
multiple contiguous MBus windows (each having a power of two size) to
cover a given PCIe BAR.
To achieve this, two functions are added: mvebu_pcie_add_windows() and
mvebu_pcie_del_windows() to respectively add and remove all the MBus
windows that are needed to map the provided PCIe region base and
size. The emulated PCI bridge code now calls those functions, instead
of directly calling the mvebu-mbus driver functions.
Fixes: 45361a4fe4 ('pci: PCIe driver for Marvell Armada 370/XP systems')
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-8-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
mvebu_pcie_handle_membase_change() and
mvebu_pcie_handle_iobase_change() do not correctly compute the window
size. PCI uses an inclusive start/end address pair, which requires a
+1 when converting to size.
This only worked because a bug in the mbus driver allowed it to
silently accept and round up bogus sizes.
Fix this by adding one to the computed size.
Fixes: 45361a4fe4 ('PCIe driver for Marvell Armada 370/XP systems')
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Willy Tarreau <w@1wt.eu>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397823593-1932-5-git-send-email-thomas.petazzoni@free-electrons.com
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This makes INTB, INTC, and INTD work on i.MX.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
This patch corrects iATU programming for cfg1, io and mem viewport. Enable
ATU only after configuring it.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Ajay Khandelwal <ajay.khandelwal@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable@vger.kernel.org
Corrects comment for setting number of lanes.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Serialization of configuration accesses is provided by 'pci_lock' in
drivers/pci/access.c thus making the driver's 'conf_lock' superfluous.
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Richard Zhu <r65037@freescale.com>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This makes INTB, INTC, and INTD work on i.MX.
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
This patch corrects iATU programming for cfg1, io and mem viewport. Enable
ATU only after configuring it.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Ajay Khandelwal <ajay.khandelwal@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable@vger.kernel.org
Corrects comment for setting number of lanes.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Intel has updated Red Hat bz1037684 to note that X79 PCH root ports also
provide isolation and the same ACS quirks apply. Some sources indicate
additional device IDs for X79, but this patch includes only the ones
specifically identified by Intel:
https://bugzilla.redhat.com/show_bug.cgi?id=1037684#c11
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
None of these files are actually using any __init type directives and hence
don't need to include <linux/init.h>. Most are just a left over from
__devinit and __cpuinit removal, or simply due to code getting copied from
one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use PCI_EXP_SLTCAP_PSN to make it easier to find code that uses the
Physical Slot Number field in the PCIe Slot Capabilities register.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Every pci_dev is on a valid pci_bus, so we don't need to test whether
dev->bus is NULL or not.
The only exceptions are a few legacy cases like alpha_core_agp_setup(),
parisc_agp_setup(), and megaraid's make_local_pdev(), where we allocate a
pci_dev with a NULL bus pointer. These are dubious uses (especially the
megaraid one), and I don't think it's possible to exercise this
pci_configure_slot() path with any of them.
Found by Coverity (CID 146446).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify populate_msi_sysfs() by
- Swapping the order of the two allocations and storing the
msi_dev_attr-derived pointer right after allocation, allowing the
cleanup code to pick things up without extra effort.
- Using kasprintf() instead of the kmalloc()/sprintf() pair.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers using these two
interfaces need to be updated to use the new pci_enable_msi_range() or
pci_enable_msi_exact() and pci_enable_msix_range() or
pci_enable_msix_exact() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use new OF interrupt mapping (of_irq_parse_and_map_pci()) when possible.
This is the recommended method of doing the IRQ mapping. For old
devicetrees we fall back to the previous practice.
This allows interrupts to be remapped across bridges.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
a staging driver; fix included. Greg KH said he'd take the patch
but hadn't as the merge window opened, so it's included here
to avoid breaking build.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=yzUO
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Nothing major: the stricter permissions checking for sysfs broke a
staging driver; fix included. Greg KH said he'd take the patch but
hadn't as the merge window opened, so it's included here to avoid
breaking build"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
staging: fix up speakup kobject mode
Use 'E' instead of 'X' for unsigned module taint flag.
VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.
kallsyms: fix percpu vars on x86-64 with relocation.
kallsyms: generalize address range checking
module: LLVMLinux: Remove unused function warning from __param_check macro
Fix: module signature vs tracepoints: add new TAINT_UNSIGNED_MODULE
module: remove MODULE_GENERIC_TABLE
module: allow multiple calls to MODULE_DEVICE_TABLE() per module
module: use pr_cont
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a few
other tiny driver core patches.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7A0wACgkQMUfUDdst+ynJNACfZlY+KNKIhNFt1OOW8rQfSZzy
1PYAnjYuOoly01JlPrpJD5b4TdxaAq71
=GVUg
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and sysfs updates from Greg KH:
"Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a
few other tiny driver core patches.
All have been in linux-next for a while"
* tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (42 commits)
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
kernfs: cache atomic_write_len in kernfs_open_file
numa: fix NULL pointer access and memory leak in unregister_one_node()
Revert "driver core: synchronize device shutdown"
kernfs: fix off by one error.
kernfs: remove duplicate dir.c at the top dir
x86: align x86 arch with generic CPU modalias handling
cpu: add generic support for CPU feature based module autoloading
sysfs: create bin_attributes under the requested group
driver core: unexport static function create_syslog_header
firmware: use power efficient workqueue for unloading and aborting fw load
firmware: give a protection when map page failed
firmware: google memconsole driver fixes
firmware: fix google/gsmi duplicate efivars_sysfs_init()
drivers/base: delete non-required instances of include <linux/init.h>
kernfs: fix kernfs_node_from_dentry()
ACPI / platform: drop redundant ACPI_HANDLE check
kernfs: fix hash calculation in kernfs_rename_ns()
kernfs: add CONFIG_KERNFS
sysfs, kobject: add sysfs wrapper for kernfs_enable_ns()
...
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
Pull irq code updates from Thomas Gleixner:
"The irq department proudly presents:
- Another tree wide sweep of irq infrastructure abuse. Clear winner
of the trainwreck engineering contest was:
#include "../../../kernel/irq/settings.h"
- Tree wide update of irq_set_affinity() callbacks which miss a cpu
online check when picking a single cpu out of the affinity mask.
- Tree wide consolidation of interrupt statistics.
- Updates to the threaded interrupt infrastructure to allow explicit
wakeup of the interrupt thread and a variant of synchronize_irq()
which synchronizes only the hard interrupt handler. Both are
needed to replace the homebrewn thread handling in the mmc/sdhci
code.
- New irq chip callbacks to allow proper support for GPIO based irqs.
The GPIO based interrupts need to request/release GPIO resources
from request/free_irq.
- A few new ARM interrupt chips. No revolutionary new hardware, just
differently wreckaged variations of the scheme.
- Small improvments, cleanups and updates all over the place"
I was hoping that that trainwreck engineering contest was a April Fools'
joke. But no.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (68 commits)
irqchip: sun7i/sun6i: Disable NMI before registering the handler
ARM: sun7i/sun6i: dts: Fix IRQ number for sun6i NMI controller
ARM: sun7i/sun6i: irqchip: Update the documentation
ARM: sun7i/sun6i: dts: Add NMI irqchip support
ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller
genirq: Export symbol no_action()
arm: omap: Fix typo in ams-delta-fiq.c
m68k: atari: Fix the last kernel_stat.h fallout
irqchip: sun4i: Simplify sun4i_irq_ack
irqchip: sun4i: Use handle_fasteoi_irq for all interrupts
genirq: procfs: Make smp_affinity values go+r
softirq: Add linux/irq.h to make it compile again
m68k: amiga: Add linux/irq.h to make it compile again
irqchip: sun4i: Don't ack IRQs > 0, fix acking of IRQ 0
irqchip: sun4i: Fix a comment about mask register initialization
irqchip: sun4i: Fix irq 0 not working
genirq: Add a new IRQCHIP_EOI_THREADED flag
genirq: Document IRQCHIP_ONESHOT_SAFE flag
ARM: sunxi: dt: Convert to the new irq controller compatibles
irqchip: sunxi: Change compatibles
...
Summary of http://lkml.org/lkml/2014/3/14/363 :
Ted: module_param(queue_depth, int, 444)
Joe: 0444!
Rusty: User perms >= group perms >= other perms?
Joe: CLASS_ATTR, DEVICE_ATTR, SENSOR_ATTR and SENSOR_ATTR_2?
Side effect of stricter permissions means removing the unnecessary
S_IFREG from several callers.
Note that the BUILD_BUG_ON_ZERO((perm) & 2) test was removed: a fair
number of drivers fail this test, so that will be the debate for a
future patch.
Suggested-by: Joe Perches <joe@perches.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> for drivers/pci/slot.c
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* pci/resource: (26 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
PCI: Remove pci_find_parent_resource() use for allocation
...
Make a note in dmesg when we overwrite legacy IDE BAR info. We previously
logged something like this:
pci 0000:00:1f.1: reg 0x10: [io 0x0000-0x0007]
and then silently overwrote the resource. There's an example in the
bugzilla below. This doesn't fix the bugzilla; it just makes what's going
on more obvious.
No functional change; merely adds some dev_info() calls.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=48451
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_bus_alloc_resource() "type_mask" parameter is used to compare with
the "flags" member of a struct resource, so it should be the same type,
namely "unsigned long".
No functional change because all current IORESOURCE_* flags fit in 32 bits.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When allocating space from a bus resource, i.e., from apertures leading to
this bus, make sure the entire resource type matches. The previous code
assumed the IORESOURCE_TYPE_BITS field was a bitmask with only a single bit
set, but this is not true. IORESOURCE_TYPE_BITS is really an enumeration,
and we have to check all the bits.
See 72dcb11972 ("resources: Add register address resource type").
No functional change. If we used this path for allocating IRQs, DMA
channels, or bus numbers, this would fix a bug because those types are
indistinguishable when masked by IORESOURCE_IO | IORESOURCE_MEM. But we
don't, so this shouldn't make any difference.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Paul reported that after f75b99d5a7 ("PCI: Enforce bus address limits in
resource allocation") on a 32-bit kernel (CONFIG_PHYS_ADDR_T_64BIT not
set), intel-gtt complained "can't ioremap flush page - no chipset
flushing". In addition, other PCI resource allocations, e.g., for bridge
windows, failed.
This happens because we incorrectly skip bus resources of
[mem 0x00000000-0xffffffff] because we think they are of size zero.
When resource_size_t is 32 bits wide, resource_size() on
[mem 0x00000000-0xffffffff] returns 0 because (r->end - r->start + 1)
overflows.
Therefore, we can't use "resource_size() == 0" to decide that allocation
from this resource will fail. allocate_resource() should fail anyway if it
can't satisfy the address constraints, so we should just depend on that.
A [mem 0x00000000-0xffffffff] bus resource is obviously not really valid,
but we do fall back to it as a default when we don't have information about
host bridge apertures.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71611
Fixes: f75b99d5a7 PCI: Enforce bus address limits in resource allocation
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many architectures implement pcibios_enable_device() the same way, so
provide a default implementation in the core.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Don't enable memory or I/O decoding if we haven't assigned or claimed the
BAR's resource.
If we enable decoding for a BAR that hasn't been assigned an address, we'll
likely cause bus conflicts. This declines to enable decoding for resources
with IORESOURCE_UNSET.
Note that drivers can use pci_enable_device_io() or pci_enable_device_mem()
if they only care about specific types of BARs. In that case, we don't
bother checking whether the corresponding resources are assigned or
claimed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* acpi-hotplug:
ACPI / hotplug: Rework deferred execution of acpi_device_hotplug()
ACPI / dock: Update copyright notice
ACPI / dock: Drop remove_dock_dependent_devices()
ACPI / dock: Drop struct acpi_dock_ops and all code related to it
ACPI / ATA: Add hotplug contexts to ACPI companions of SATA devices
ACPI / dock: Add .uevent() callback to struct acpi_hotplug_context
ACPI / dock: Use callback pointers from devices' ACPI hotplug contexts
ACPI / dock: Use ACPI device object pointers instead of ACPI handles
ACPI / hotplug: Add .fixup() callback to struct acpi_hotplug_context
ACPI / hotplug / PCI: Do not clear event callback pointer for docks
ACPI / dock: Associate dock platform devices with ACPI device objects
ACPI / dock: Pass ACPI device pointer to acpi_device_is_battery()
ACPI / dock: Dispatch dock notifications from the global notify handler
Paul reported that after f75b99d5a7 ("PCI: Enforce bus address limits in
resource allocation") on a 32-bit kernel (CONFIG_PHYS_ADDR_T_64BIT not
set), intel-gtt complained "can't ioremap flush page - no chipset
flushing". In addition, other PCI resource allocations, e.g., for bridge
windows, failed.
This happens because we incorrectly skip bus resources of
[mem 0x00000000-0xffffffff] because we think they are of size zero.
When resource_size_t is 32 bits wide, resource_size() on
[mem 0x00000000-0xffffffff] returns 0 because (r->end - r->start + 1)
overflows.
Therefore, we can't use "resource_size() == 0" to decide that allocation
from this resource will fail. allocate_resource() should fail anyway if it
can't satisfy the address constraints, so we should just depend on that.
A [mem 0x00000000-0xffffffff] bus resource is obviously not really valid,
but we do fall back to it as a default when we don't have information about
host bridge apertures.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71611
Fixes: f75b99d5a7 PCI: Enforce bus address limits in resource allocation
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Andreas reported that after 1f42db786b ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.
This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.
Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device(). But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.
This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.
Fixes: 1f42db786b PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andreas reported that after 1f42db786b ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.
This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.
Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device(). But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.
This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.
Fixes: 1f42db786b PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691
Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Make the ACPI-based PCI hotplug (ACPIPHP) code use
pci_device_is_present() for checking if devices are present instead
of open coding the same thing.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no reason to care about irq_desc in that context, escpecially
as irq_data for that interrupt is retrieved as well.
Use the proper accessor for the msi descriptor
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: pci <linux-pci@vger.kernel.org>
Link: http://lkml.kernel.org/r/20140223212736.987803648@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Runtime-suspended devices are resumed during system suspend by
pci_pm_prepare() for two reasons: First, because they may need
to be reprogrammed in order to change their wakeup settings and,
second, because they may need to be operatonal for their children
to be successfully suspended. That is a problem, though, if there
are many runtime-suspended devices that need to be resumed this
way during system suspend, because the .prepare() PM callbacks of
devices are executed sequentially and the times taken by them
accumulate, which may increase the total system suspend time quite
a bit.
For this reason, move the resume of runtime-suspended devices up
to the next phase of device suspend (during system suspend), except
for the ones that have power.ignore_children set. The exception is
made, because the devices with power.ignore_children set may still
be necessary for their children to be successfully suspended (during
system suspend) and they won't be resumed automatically as a result
of the runtime resume of their children.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
If we don't support 64-bit addresses, i.e., CONFIG_PHYS_ADDR_T_64BIT is not
set, we can't deal with BARs above 4GB. In this case we already pretend
the BAR contained zero; this patch also sets IORESOURCE_UNSET so we can try
to reallocate it later.
I don't think this is exactly correct: what we care about here are *bus*
addresses, not CPU addresses, so the tests of sizeof(resource_size_t)
probably should be on sizeof(dma_addr_t) instead. But this is what's been
in -next, so we'll fix that later.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the IORESOURCE_UNSET bit is set, it means we haven't assigned an address
yet, so don't try to claim the region.
Also, make the error messages more uniform and add info about which BAR is
involved.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check to make sure we don't update a BAR with an address we haven't
assigned.
If we haven't assigned an address to a resource, we shouldn't write it to a
BAR. This isn't a problem for the usual path via pci_assign_resource(),
which clears IORESOURCE_UNSET before calling pci_update_resource(), but
paths like pci_restore_bars() can call this for resources we haven't
assigned.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clear IORESOURCE_UNSET when we assign an address to a resource, not when we
write the address to the BAR.
Also, drop the "BAR %d: set to %pR" message; this is mostly redundant with
the "BAR %d: assigned %pR" message from pci_assign_resource().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When assigning addresses to resources, mark them with IORESOURCE_UNSET
before we start and clear IORESOURCE_UNSET if assignment is successful.
That means that if we print the resource during assignment, we will show
the size, not a meaningless address.
Also, clear IORESOURCE_UNSET if we do assign an address, so we print the
address when it is valid.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the resource hasn't been allocated yet, pci_find_parent_resource() is
documented as returning the region "where it should be allocated from."
This is impossible in general because there may be several candidates: a
prefetchable BAR can be put in either a prefetchable or non-prefetchable
window, a transparent bridge may have overlapping positively- and
subtractively-decoded windows, and a root bus may have several windows of
the same type.
Allocation should be done by pci_bus_alloc_resource(), which iterates
through all bus resources and looks for the best match, e.g., one with the
desired prefetchability attributes, and falls back to less-desired
possibilities.
The only valid use of pci_find_parent_resource() is to find the parent of
an already-allocated resource so we can claim it via request_resource(),
and all we need for that is a bus region of the correct type that contains
the resource.
Note that like 8c8def26bf ("PCI: allow matching of prefetchable resources
to non-prefetchable windows"), this depends on pci_bus_for_each_resource()
iterating through positively-decoded regions before subtractively-decoded
ones. We prefer not to return a subtractively-decoded region because
requesting from it will likely conflict with the overlapping positively-
decoded window (see Launchpad report below).
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/424142
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Linus Torvalds <torvalds@linux-foundation.org>
The SGI Visual Workstation seems to be dead; remove support so we
don't have to continue maintaining it.
Cc: Andrey Panin <pazke@donpac.ru>
Cc: Michael Reed <mdr@sgi.com>
Link: http://lkml.kernel.org/r/530CFD6C.7040705@zytor.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We have two identical copies of resource_contains() already, and more
places that could use it. This moves it to ioport.h where it can be
shared.
resource_contains(struct resource *r1, struct resource *r2) returns true
iff r1 and r2 are the same type (most callers already checked this
separately) and the r1 address range completely contains r2.
In addition, the new resource_contains() checks that both r1 and r2 have
addresses assigned to them. If a resource is IORESOURCE_UNSET, it doesn't
have a valid address and can't contain or be contained by another resource.
Some callers already check this or for res->start.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update the R-Car Generation 2 PCI driver Kconfig dependencies to follow
same style as other drivers - no SoC dependencies.
Also, update the COMPILE_TEST bits to depend on ARM. This since the DMA
bounce buffer and dma_ops handling code is ARM specific.
[bhelgaas: adjust context after dropping DMABOUNCE patches]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
In order to avoid the need to register special ACPI dock
operations for SATA devices add a .uevent() callback pointer to
struct acpi_hotplug_context and make dock_hotplug_event() use that
callback if available. Also rename the existing .event() callback
in struct acpi_hotplug_context to .notify() to avoid possible
confusion in the future.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of requiring a set of special dock operations to be registered
via register_hotplug_dock_device() for each ACPI dock device, it is
much more straightforward to use callback pointers from the devices'
hotplug contexts if available.
For this reason, modify dock_hotplug_event() to use callback pointers
from the hotplug contexts of ACPI devices and fall back to using the
special dock operarions only if those callbacks are missing. Also
make the ACPI-based PCI hotplug (ACPIPHP) subsystem set the .fixup
callback pointer in the hotplug contexts of devices handled by it to
a new function, acpiphp_post_dock_fixup(), so that the dock station
driver can use the callbacks from those contexts instead of special
dock operations registered via register_hotplug_dock_device().
Along with the above changes drop the ACPIPHP's dock operations that
are not necessary any more.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rework the ACPI dock station driver to store ACPI device object
pointers instead of ACPI handles in its internal data structures.
The purpose is moslty to make subsequent simplifications possible,
but also this allows the overall code size to be reduced slightly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order for the ACPI dock station code to be able to use the
callbacks pointed to by the ACPI device objects' hotplug contexts
add a .fixup() callback pointer to struct acpi_hotplug_context.
That callback will be useful to handle PCI devices located in
dock stations.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After recent changes adding dock station handling to the ACPI hotplug
core, it is not necessary to clear the .event() pointer in the
ACPIPHP device hotplug context for dock stations any more, so don't
do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/dead-code:
PCI: Remove unused SR-IOV VF Migration support
iommu/amd: Add include of <linux/irqreturn.h>
mei: Add include of <linux/irqreturn.h>
misc: mic: Add include of <linux/irqreturn.h>
* pci/pciehp:
PCI: pciehp: Cleanup whitespace
PCI: pciehp: Remove a non-existent card, regardless of "surprise" capability
PCI: pciehp: Don't turn slot off when hot-added device already exists
PCI: pciehp: Add hotplug_lock to serialize hotplug events
PCI: pciehp: Ensure very fast hotplug events are also processed
PCI: pciehp: Disable link notification across slot reset
PCI: pciehp: Don't check adapter or latch status while disabling
PCI: pciehp: Don't disable the link permanently during removal
PCI: pciehp: Enable link state change notifications
PCI: pciehp: Use link change notifications for hot-plug and removal
PCI: pciehp: Make check_link_active() non-static
MSI
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CTv7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most interesting thing here is the change to enable INTx (by
clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
Apparently the Baytrail BIOS does this, which means EHCI doesn't work.
Also, fix an AHCI MSI regression and other issues with the recent MSI
changes. This also adds pci_enable_msi_exact() and
pci_enable_msix_exact(), which aren't regression fixes, but will keep
us from touching drivers twice (once to stop using the deprecated
pci_enable_msi(), etc., and again to use the *_exact() variants).
There's also a minor MVEBU fix.
Summary:
MSI:
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous:
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"
* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ahci: Fix broken fallback to single MSI mode
PCI: Enable INTx if BIOS left them disabled
PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
PCI/MSI: Fix cut-and-paste errors in documentation
PCI/MSI: Add pci_enable_msi() documentation back
PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
PCI/MSI: Fix leak of msi_attrs
PCI/MSI: Check kmalloc() return value, fix leak of name
PCI: mvebu: Use Device ID and revision from underlying endpoint
In case a card is physically yanked out, it should immediately be removed,
regardless of the "surprise" capability bit. Thus:
- Always handle the physical removal - regardless of the "surprise" bit.
- Don't use "surprise" capability when making decisions about enabling
presence detect notifications.
- Reword the comments to indicate the intent.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch handles the case where the PCIe link is up and running, yet
drops into the LTSSM training mode. The link spends short time in the LTSSM
training mode, but the current code can misinterpret it as the link being
stalled. Waiting for the LTSSM training to complete fixes the issue.
Quoting Sascha:
This is broken since commit 7f9f40c01c ('PCI: imx6: Report "link up"
only after link training completes').
The designware driver changes the PORT_LOGIC_SPEED_CHANGE bit in
dw_pcie_host_init() which causes the link to be retrained. During the
next call to dw_pcie_rd_conf() the link is then reported being down and
the function returns PCIBIOS_DEVICE_NOT_FOUND resulting in nonfunctioning
PCIe.
Fixes: 7f9f40c01c (PCI: imx6: Report "link up" only after link training completes)
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
The Synopsys PCIe core provides one pair of 32-bit BARs (BAR 0 and BAR 1).
The BARs can be configured as follows:
- One 64-bit BAR: BARs 0 and 1 are combined to form a single 64-bit BAR
- Two 32-bit BARs: BARs 0 and 1 are two independent 32-bit BARs
This patch corrects 64-bit, non-prefetchable memory BAR configuration
implemented in dw driver.
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org # v3.12+
This reverts commit 74bb1bcc7d ("PCI: handle SR-IOV Virtual Function
Migration"), removing this exported interface:
pci_sriov_migration()
Since pci_sriov_migration() is unused, it is impossible to schedule
sriov_migration_task() or use any of the other migration infrastructure.
This is based on Stephen Hemminger's patch (see link below), but goes a bit
further.
Link: http://lkml.kernel.org/r/20131227132710.7190647c@nehalam.linuxnetplumber.net
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
* pci/misc:
PCI: Enable INTx if BIOS left them disabled
ia64/PCI: Set IORESOURCE_ROM_SHADOW only for the default VGA device
x86/PCI: Set IORESOURCE_ROM_SHADOW only for the default VGA device
PCI: Update outdated comment for pcibios_bus_report_status()
PCI: Cleanup per-arch list of object files
PCI: cpqphp: Fix hex vs decimal typo in cpqhpc_probe()
x86/PCI: Fix function definition whitespace
x86/PCI: Reword comments
x86/PCI: Remove unnecessary local variable initialization
PCI: Remove unnecessary list_empty(&pci_pme_list) check
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
* pci/host-mvebu:
PCI: mvebu: Call request_resource() on the apertures
bus: mvebu-mbus: Fix incorrect size for PCI aperture resources
PCI: mvebu: Fix potential issue in range parsing
PCI: mvebu: Use Device ID and revision from underlying endpoint
* pci/list-for-each-entry:
PCI: Remove pci_bus_b() and use list_for_each_entry() directly
pcmcia: Use list_for_each_entry() for bus traversal
powerpc/PCI: Use list_for_each_entry() for bus traversal
drm: Use list_for_each_entry() for bus traversal
ARM/PCI: Use list_for_each_entry() for bus traversal
ACPI / hotplug / PCI: Use list_for_each_entry() for bus traversal
It is typical for host drivers to request a resource for the aperture; once
this is done the PCI core will properly populate resources for all BARs in
the system.
With this patch cat /proc/iomem will now show:
e0000000-efffffff : PCI MEM 0000
e0000000-e00fffff : PCI Bus 0000:01
e0000000-e001ffff : 0000:01:00.0
Tested on Kirkwood.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Break out the hard coded window size code to allow dynamic setup. The
window size is still left at 1GiB but with this patch changing window size
is easy for testing.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Convert the code to allow per-device probe() like other device drivers.
This also delays driver registration due to change from subsys_initcall()
to regular module_platform_driver().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The bridge logic at slot 0 only supports reads up to 0x40 and the rest of
the PCI configuration space for this slot is marked as reserved in the
manual.
Trying a read from offset 0x100 is producing an error from the bridge. With
error interrupts enabled, the following is printed:
pci-rcar-gen2 ee0d0000.pci: error irq: status 00000014
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Add option to enable interrupts to report any errors from the AHB-PCI
bridge to help find any issues with the bridge when in use.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The current code does not check the return from platform_get_irq() so add
an error check and return if this call does fail.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Currently, ACPIPHP does not add hotplug context to devices that
should be handled by the native PCI hotplug (PCIeHP) code. The
reason why was because PCIeHP didn't know about the devices'
connections with ACPI and would not clean up things properly
during an eject of an ACPI-backed device, for example.
However, after recent changes that made the ACPI core create struct
acpi_device objects for all namespace nodes regardless of the
underlying devices' status and added PCI rescan-remove locking to
both ACPIPHP and PCIeHP, that concern is not valid any more.
Namely, after those changes PCIeHP need not care about the ACPI
side of things any more and it should be serialized with respect to
ACPIPHP and they won't be running concurrently with each other in
any case.
For this reason, make ACPIPHP to add its hotplug context to
all devices with ACPI companions, even the ones that should be
handled by PCIeHP in principle. That may work around hotplug
issues on some systems where PCIeHP is supposed to work, but it
doesn't and the ACPI hotplug signaling works instead.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The name of register_slot() doesn't really reflect what the function
is does, so rename it to acpiphp_add_context() and add a proper
kerneldoc comment to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/msi:
vfio: Use pci_enable_msi_range() and pci_enable_msix_range()
ahci: Use pci_enable_msi_range() instead of pci_enable_msi_block()
ahci: Fix broken fallback to single MSI mode
PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
PCI/MSI: Fix cut-and-paste errors in documentation
PCI/MSI: Add pci_enable_msi() documentation back
PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
PCI/MSI: Fix leak of msi_attrs
PCI/MSI: Check kmalloc() return value, fix leak of name
Some firmware leaves the Interrupt Disable bit set even if the device uses
INTx interrupts. Clear Interrupt Disable so we get those interrupts.
Based on the report mentioned below, if the user selects the "EHCI only"
option in the Intel Baytrail BIOS, the EHCI device is handed off to the OS
with the PCI_COMMAND_INTX_DISABLE bit set.
Link: http://lkml.kernel.org/r/20140114181721.GC12126@xanatos
Link: https://bugzilla.kernel.org/show_bug.cgi?id=70601
Reported-by: Chris Cheng <chris.cheng@atrustcorp.com>
Reported-and-tested-by: Jamie Chen <jamie.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Replace list_for_each() with list_for_each_entry(), which means we no
longer need pci_bus_b() and can remove it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The second parameter of of_read_number() is not the index, but a size. As
it happens, in this case it may work just fine because of the conversion to
u32 and the favorable endianness on this architecture.
Fixes: 11be65472a ("PCI: mvebu: Adapt to the new device tree layout")
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # v3.12+
Replace list_for_each() + pci_bus_b() with list_for_each_entry().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
If we found device already exists during hot add device, we should leave
it, not turn the slot off.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Coverity reported that I forgot to clean up some allocated memory on the
error path in populate_msi_sysfs(), so this patch fixes that.
Thanks to Dave Jones for pointing out where the error was, I obviously
can't read code this morning...
Found by Coverity (CID 1163317).
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dave Jones <davej@redhat.com>
Coverity reported that I forgot to check the return value of kmalloc() when
creating the MSI attribute name, so fix that up and properly free it if
there is an error when allocating the msi_dev_attr variable.
Found by Coverity (CID 1163315 and 1163316).
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
setup-bus.o is now included unconditionally as of commit 7dc3030334
("PCI: Always build setup-bus when PCI is enabled"). Remove it from the
per-arch list of object files.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is a static checker fix and I can't test it, but from the context it
definitely looks like hexadecimal 0x20 was intended here instead of decimal
20.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Marvell SoCs place the SoC number into the PCIe endpoint device ID. The
SoC stepping is placed into the PCIe revision. The old plat-orion PCIe
driver allowed this information to be seen in user space with a simple
lspci command.
The new driver places a virtual PCI-PCI bridge on top of these endpoints.
It has its own hard coded PCI device ID. Thus it is no longer possible to
see what the SoC is using lspci.
When initializing the PCI-PCI bridge, set its device ID and revision from
the underlying endpoint, thus restoring this functionality. Debian would
like to use this in order to aid installing the correct DTB file.
Fixes: 45361a4fe4 ("pci: PCIe driver for Marvell Armada 370/XP systems")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # v3.11+
Marvell SoCs place the SoC number into the PCIe endpoint device ID. The
SoC stepping is placed into the PCIe revision. The old plat-orion PCIe
driver allowed this information to be seen in user space with a simple
lspci command.
The new driver places a virtual PCI-PCI bridge on top of these endpoints.
It has its own hard coded PCI device ID. Thus it is no longer possible to
see what the SoC is using lspci.
When initializing the PCI-PCI bridge, set its device ID and revision from
the underlying endpoint, thus restoring this functionality. Debian would
like to use this in order to aid installing the correct DTB file.
Fixes: 45361a4fe4 ("pci: PCIe driver for Marvell Armada 370/XP systems")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org # v3.11+
The ACPI specification (ACPI 5.0A, Section 6.3.7) says:
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which
no device driver should be loaded (for example, a bridge device.)
Children of this device may be present and valid. OSPM should
continue enumeration below a device whose _STA returns this bit
combination.
Evidently, some BIOSes follow that and return 0x0A from _STA, which
causes problems to happen when they trigger bus check or device check
notifications for those devices too. Namely, ACPIPHP thinks that they
are gone and may drop them, for example, if such a notification is
triggered during a resume from system suspend.
To fix that, modify ACPICA to regard devies as present and
functioning if _STA returns both the ACPI_STA_DEVICE_ENABLED
and ACPI_STA_DEVICE_FUNCTIONING bits set for them.
Reported-and-tested-by: Peter Wu <lekensteyn@gmail.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Subject and changelog, minor code modifications]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Today it is there is no protection around pciehp_enable_slot() and
pciehp_disable_slot() to ensure that they complete before another
hot-plug operation can be done on that particular slot.
This patch introduces the slot->hotplug_lock to ensure that any hotplug
operations (add / remove) complete before another hotplug event can begin
processing on that particular slot.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Today, this is how all the hotplug and unplug events work:
Hotplug / Removal needs to be done
=> Set slot->state (protected by slot->lock) to either
POWERON_STATE (for enabling) or POWEROFF_STATE (for disabling).
=> Submit the work item for pciehp_power_thread() to slot->wq.
Problem:
There is a problem if the hotplug events can happen fast enough that
they do not give SW enough time to add or remove the new devices.
=> Assume: Event for unplug comes (e.g. surprise removal). But
before the pciehp_power_thread() work item was executed, the
card was replaced by another card, causing surprise hotplug event.
=> What goes wrong:
=> The hot-removal event sets slot->state to POWEROFF_STATE, and
schedules the pciehp_power_thread().
=> The hot-add event sets slot->state to POWERON_STATE, and
schedules the pciehp_power_thread().
=> Now the pciehp_power_thread() is scheduled twice, and on both
occasions it will find POWERON_STATE and will try to add the
devices on the slot, and will fail complaining that the devices
already exist.
=> Why this is a problem: If the device was replaced between the hot
removal and hot-add, then we should unload the old driver and
reload the new one. This does not happen today. The kernel or the
driver is not even aware that the device was replaced.
The problem is that the pciehp_power_thread() only looks at the
slot->state which would only contain the *latest* state - not
the actual event (add / remove) that was the intent of the IRQ
handler who submitted the work.
What this patch does:
=> Hotplug events pass on an actual request (for addition or removal)
to pciehp_power_thread() which is local to that work item
submission.
=> pciehp_power_thread() does not need to look at slote->state and
hence no locks needed in that.
=> Essentially this results in all the hotplug and unplug events
"replayed" by pciehp_power_thread().
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Disable the link notification (in addition to presence detect
notifications) across the slot reset since the reset could flap the link,
and we don't want to treat it as hot unplug followed by a hotplug.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It does not make much sense to refuse to disable a slot if an adapter is
not present or the latch is open. If an adapter is not present, it provides
an even better reason to disable the device slot.
This is specially a problem for link state hot-plug, because some ports use
in band mechanism for presence detection. Thus when link goes down,
presence detect also goes down. We _want_ that the removal should take
place in such case.
Thus remove the checks for adapter and latch in pciehp_disable_slot()
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We need future link up events for hot-add, thus don't disable the link
permanently during device removal. Also, remove the static functions that
are now left unused.
This reverts part of 2debd92899 ("PCI: pciehp: Disable/enable link during
slot power off/on"). This was discussed at the URL below, where it was
revealed that it was done for a bug in a PCIe repeater chip on that
particular platform.
Link: https://lkml.kernel.org/r/CAErSpo72KZ-a2OSQLWoK71GCgwBt676XZdGt4tEYm-6UYnLmPw@mail.gmail.com
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enable the Link state notifications unconditionally. Enable the
presence detection notification only if attention button is absent.
This was discussed at this thread:
https://lkml.kernel.org/r/529E5C0E.80903@gmail.com
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When assigning a new bus number in pci_scan_bridge we check whether
max+1 is free by calling pci_find_bus. If it does already exist then we
assume that we are rescanning and that this is the right bus to scan.
This is fragile. If max+1 lies outside of bus->busn_res.end then we will
rescan some random bus from somewhere else in the hierachy. This patch
checks for this case and prints a warning.
[bhelgaas: add parent/child bus number info to dev_warn()]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_scan_child_bus can (potentially) return a bus number higher than the
subordinate value of the child bus. Possible reasons are that bus numbers
are reserved for SR-IOV or for CardBus (SR-IOV is done without checks and
the CardBus checks are sketchy at best).
We clamp the returned value to the actual subordinate value and print a
warning if too many bus numbers are reserved.
[bhelgaas: whitespace]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function has no effect.
If pcibios_assign_all_busses() is not set then the function does nothing.
If it is set then in pci_scan_bridge we are always in the branch where
we assign the bus numbers ourselves and the subordinate values of all
parent busses will be set to 0xff since that is what they inherited from
their parent bus and ultimately from the root bus.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Many of the currently available Intel PCH-based root ports do not provide
PCIe ACS capabilities. Without this, we must assume that peer-to-peer
traffic between multifunction root ports and between devices behind root
ports is possible. This lack of isolation is exposed by grouping the
devices together in the same IOMMU group. If we want to expose these
devices to userspace, vfio uses IOMMU groups as the unit of ownership, thus
making it very difficult to assign individual devices to separate users.
The good news is that the chipset does provide ACS-like isolation
capabilities, but we do need to verify and enable those capabilities if the
BIOS has not done so. This patch implements the device specific enabling
and testing of equivalent ACS function for these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Don Dugger <donald.d.dugger@intel.com>
Some devices support PCI ACS-like features, but don't report it using the
standard PCIe capabilities. We already provide hooks for device-specific
testing of ACS, but not for device-specific enabling of ACS. This provides
that setup hook.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A lot of systems do not have the fancy buttons and LEDs, and instead
want to rely only on the Link state change events to drive the hotplug
and removal state machinery.
(http://www.spinics.net/lists/hotplug/msg05802.html)
This patch adds support for that functionality. Here are the details
about the patch itself:
* Define and use interrupt events for linkup / linkdown.
* Make the pcie_isr() also look at link events, and direct control to
corresponding (new) link state change handler function.
* Introduce the functions to handle link-up and link-down events and
queue the add / removal work in the slot->wq to be processed by
pciehp_power_thread()
As a side note, this patch also fixes the bug
https://bugzilla.kernel.org/show_bug.cgi?id=65521 "pciehp ignores Data Link
Layer State Changed bit."
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
check_link_active() functionality needs to be used by subsequent patches
(that introduce link state change based hotplug). Thus make the function
non-static, and rename it to pciehp_check_link_active() so as to be
consistent with other non-static functions.
Signed-off-by: Rajat Jain <rajatxjain@gmail.com>
Signed-off-by: Rajat Jain <rajatjain@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
da9846ae15 ("kernfs: make kernfs_deactivate() honor KERNFS_LOCKDEP
flag") in driver-core-linus conflicts with kernfs_drain() updates in
driver-core-next. The former just adds the missing KERNFS_LOCKDEP
checks which are already handled by kernfs_lockdep() checks in
driver-core-next. The conflict can be resolved by taking code from
driver-core-next.
Conflicts:
fs/kernfs/dir.c
Right now we use 0xff for busn_res.end when probing and later reduce it to
the value that is actually used. This does not work if a parent bridge has
already a lower subordinate value. For example during hotplug of a new
bridge below an already-configured bridge the following message is printed
from pci_bus_insert_busn_res():
pci_bus 0000:06: busn_res: can not insert [bus 06-ff] under [bus 05-9b] (conflicts with (null) [bus 05-9b])
This patch clamps the bus range to that of the parent and also ensures that
we do not exceed the parents range when assigning the final subordinate
value.
We also check that busses configured by the firmware fit into their parents
bounds.
[bhelgaas: reword dev_warn() and fix printk format warning]
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If a conflict happens during insert_resource_conflict() and all conflicts
fit within the newly inserted resource then they will become children of
the new resource. This is almost certainly not what we want for bus
numbers.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Right now the CardBus code in pci_scan_bridge() is executed during both
passes. Since we always allocate the bus number ourselves it makes sense
to put it into the second pass.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Initially when we encountered a bus that was already present we skipped
it. Since 74710ded8e 'PCI: always scan child buses' we continue
scanning in order to allow user triggered rescans of already existing
busses.
The old comment suggested that the reason for continuing the scan is a
bug in the i450NX chipset. This is not the case.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes two small issues:
- If pci_add_new_bus() fails, max must not be incremented. Otherwise
an incorrect value is returned from pci_scan_bridge().
- If the bus is already present, max must be incremented. I think
that this case should only be hit if we trigger a manual rescan of a
CardBus bridge.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since acpi_device_hotplug() assumes that ACPI handles of device
objects passed to it will not become invalid while acpi_scan_lock
is being held, make acpiphp_disable_slot() acquire acpi_scan_lock,
because it generally causes _EJ0 to be executed for one of the
devices in the slot and that may cause its ACPI handle to become
invalid.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
driver-core now supports synchrnous self-deletion of attributes and
the asynchrnous removal mechanism is scheduled for removal. Use it
instead of device_schedule_callback(). This makes "remove" behave
synchronously.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the only existing caller of acpiphp_check_host_bridge(),
which is acpi_pci_root_scan_dependent(), already has a struct
acpi_device pointer needed to obtain the ACPIPHP context, it
doesn't make sense to execute acpi_bus_get_device() on its
handle in acpiphp_handle_to_bridge() just in order to get that
pointer back.
For this reason, modify acpiphp_check_host_bridge() to take
a struct acpi_device pointer as its argument and rearrange the
code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since acpi_bus_notify() is executed on all notifications for all
devices anyway, make it execute acpi_device_hotplug() for all
hotplug events instead of installing notify handlers pointing to
the same function for all hotplug devices.
This change reduces both the size and complexity of ACPI-based device
hotplug code. Moreover, since acpi_device_hotplug() only does
significant things for devices that have either an ACPI scan handler,
or a hotplug context with .eject() defined, and those devices
had notify handlers pointing to acpi_hotplug_notify_cb() installed
before anyway, this modification shouldn't change functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpi_hotplug_notify_cb() does not use its data argument any
more, the second argument of acpi_install_hotplug_notify_handler()
can be dropped, so do that and update its callers accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI-based PCI hotplug (ACPIPHP) code currently attaches its
hotplug context objects directly to ACPI namespace nodes representing
hotplug devices. However, after recent changes causing struct
acpi_device to be created for every namespace node representing a
device (regardless of its status), that is not necessary any more.
Moreover, it's vulnerable to the theoretical issue that the ACPI
handle passed in the context between handle_hotplug_event() and
hotplug_event_work() may become invalid in the meantime (as a
result of a concurrent table unload).
In principle, this issue might be addressed by adding a non-empty
release handler for ACPIPHP hotplug context objects analogous to
acpi_scan_drop_device(), but that would duplicate the code in that
function and in acpi_device_del_work_fn(). For this reason, it's
better to modify ACPIPHP to attach its device hotplug contexts to
struct device objects representing hotplug devices and make it
use acpi_hotplug_notify_cb() as its notify handler. At the same
time, acpi_device_hotplug() can be modified to dispatch the new
.hp.event() callback pointing to acpiphp_hotplug_event() from ACPI
device objects associated with PCI devices or use the generic
ACPI device hotplug code for device objects with matching scan
handlers.
This allows the existing code duplication between ACPIPHP and the
ACPI core to be reduced too and makes further ACPI-based device
hotplug consolidation possible.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsequent changes will require the ACPI core to acquire the lock
protecting the ACPIPHP hotplug contexts, so move the definition of
the lock to the core and change its name to be more generic.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since hotplug_event() can get the ACPI handle needed for debug
printouts from its context argument, there's no need to pass the
handle to it. Moreover, the second argument's type may be changed
to (struct acpiphp_context *), because that's what is always passed
to hotplug_event() as the second argument anyway.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make hotplug_event() use acpi_handle_debug() instead of an open-coded
debug message printing and clean up the messages printed by it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
A few lines of code can be cut from hotplug_event() by defining
and initializing the slot variable at the top of the function,
so do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After recent PCI core changes related to the rescan/remove locking,
the code sections under crit_sect mutexes from ACPIPHP slot objects
are always executed under the general PCI rescan/remove lock.
For this reason, the crit_sect mutexes are simply redundant, so drop
them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
acpiphp_bus_add() is only called from one place, so move the code out
of it into that place and drop it. Also make that code use
func_to_acpi_device() to get the struct acpi_device pointer it needs
instead of calling acpi_bus_get_device() which may be costly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After recent modifications of the ACPI core making it create a struct
acpi_device object for every namespace node representing a device
regardless of the current status of that device the ACPIPHP code
can store a struct acpi_device pointer instead of an ACPI handle
in struct acpiphp_context. This immediately makes it possible to
avoid making potentially costly calls to acpi_bus_get_device() in
two places and allows some more simplifications to be made going
forward.
The reason why that is correct is because ACPIPHP only installs
hotify handlers for namespace nodes that exist when
acpiphp_enumerate_slots() is called for their parent bridge.
That only happens if the parent bridge has an ACPI companion
associated with it, which means that the ACPI namespace scope
in question has been scanned already at that point. That, in
turn, means that struct acpi_device objects have been created
for all namespace nodes in that scope and pointers to those
objects can be stored directly instead of their ACPI handles.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If a struct acpi_device pointer is passed to acpiphp_no_hotplug()
instead of an ACPI handle, the function won't need to call
acpi_bus_get_device(), which may be costly, any more. Then,
trim_stale_devices() can call acpiphp_no_hotplug() passing
the struct acpi_device object it already has directly to that
function.
Make those changes and update slot_no_hotplug() accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If trim_stale_devices() calls acpi_bus_trim() directly, we can
save a potentially costly acpi_bus_get_device() invocation. After
making that change acpiphp_bus_trim() would only be called from one
place, so move the code from it to that place and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The err label in register_slot() is only jumped to from one place,
so move the code under the label to that place and drop the label.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add proper kerneldoc comments describing acpiphp_enumerate_slots()
and acpiphp_remove_slots().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After recent PCI core changes related to the rescan/remove locking,
the ACPIPHP's disable_slot() function is only called under the
general PCI rescan/remove lock, so it doesn't have to use
dev_in_slot() any more to avoid race conditions. Make it simply
walk the devices on the bus and drop the ones in the slot being
disabled and drop dev_in_slot() which has no more users.
Moreover, to avoid problems described in the changelog of commit
29ed1f29b6 (PCI: pciehp: Fix null pointer deref when hot-removing
SR-IOV device), make disable_slot() carry out the list walk in
reverse order.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
list_for_each_entry() handles empty lists just fine, so there's no need to
check whether the list is empty first.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Coverity reported that I forgot to clean up some allocated memory on the
error path in populate_msi_sysfs(), so this patch fixes that.
Thanks to Dave Jones for pointing out where the error was, I obviously
can't read code this morning...
Found by Coverity (CID 1163317).
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dave Jones <davej@redhat.com>
Coverity reported that I forgot to check the return value of kmalloc() when
creating the MSI attribute name, so fix that up and properly free it if
there is an error when allocating the msi_dev_attr variable.
Found by Coverity (CID 1163315 and 1163316).
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If a PCI bridge with an ACPIPHP context attached is removed via
sysfs, the code path executed as a result is the following:
pci_stop_and_remove_bus_device_locked
pci_remove_bus
pcibios_remove_bus
acpi_pci_remove_bus
acpiphp_remove_slots
cleanup_bridge
unregister_hotplug_dock_device (drops dock references to the bridge)
put_bridge
free_bridge
acpiphp_put_context (for each child, under context lock)
kfree (context)
Now, if a dock event affecting one of the bridge's child devices
occurs (roughly at the same time), it will lead to the following code
path:
acpi_dock_deferred_cb
dock_notify
handle_eject_request
hot_remove_dock_devices
dock_hotplug_event
hotplug_event (dereferences context)
That may lead to a kernel crash in hotplug_event() if it is executed
after the last kfree() in the bridge removal code path.
To prevent that from happening, add a wrapper around hotplug_event()
called dock_event() and point the .handler pointer in acpiphp_dock_ops
to it. Make that wrapper retrieve the device's ACPIPHP context using
acpiphp_get_context() (instead of taking it from the data argument)
under acpiphp_context_lock and check if the parent bridge's
is_going_away flag is set. If that flag is set, it will return
immediately and if it is not set it will grab a reference to the
device's parent bridge before executing hotplug_event().
Then, in the above scenario, the reference to the parent bridge
held by dock_event() will prevent free_bridge() from being executed
for it until hotplug_event() returns.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a PCI bridge with an ACPIPHP context attached is removed via
sysfs, the code path executed as a result is the following:
pci_stop_and_remove_bus_device_locked
pci_remove_bus
pcibios_remove_bus
acpi_pci_remove_bus
acpiphp_remove_slots
cleanup_bridge
put_bridge
free_bridge
acpiphp_put_context (for each child, under context lock)
kfree (child context)
Now, if a hotplug notify is dispatched for one of the bridge's
children and the timing is such that handle_hotplug_event() for
that notify is executed while free_bridge() above is running,
the get_bridge(context->func.parent) in handle_hotplug_event()
will not really help, because it is too late to prevent the bridge
from going away and the child's context may be freed before
hotplug_event_work() scheduled from handle_hotplug_event()
dereferences the pointer to it passed via the data argument.
That will cause a kernel crash to happpen in hotplug_event_work().
To prevent that from happening, make handle_hotplug_event()
check the is_going_away flag of the function's parent bridge
(under acpiphp_context_lock) and bail out if it's set. Also,
make cleanup_bridge() set the bridge's is_going_away flag under
acpiphp_context_lock so that it cannot be changed between the
check and the subsequent get_bridge(context->func.parent) in
handle_hotplug_event().
Then, in the above scenario, handle_hotplug_event() will notice
that context->func.parent->is_going_away is already set and it
will exit immediately preventing the crash from happening.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpiphp_check_bridge() called by acpiphp_check_host_bridge()
does things that require PCI rescan-remove locking around it,
make acpiphp_check_host_bridge() use that locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit 9217a98467 (ACPI / hotplug / PCI: Use global PCI rescan-remove
locking) modified ACPIPHP to protect its PCI device removal and addition
code paths from races against sysfs-driven rescan and remove operations
with the help of PCI rescan-remove locking. However, it overlooked the
fact that hotplug_event_work() is not the only caller of hotplug_event()
which may also be called by dock_hotplug_event() and that code path
is missing the PCI rescan-remove locking. This means that, although
the PCI rescan-remove lock is held as appropriate during the handling
of events originating from handle_hotplug_event(), the ACPIPHP's
operations resulting from dock events may still suffer the race
conditions that commit 9217a98467 was supposed to eliminate.
To address that problem, move the PCI rescan-remove locking from
hotplug_event_work() to hotplug_event() so that it is used regardless
of the way that function is invoked.
Revamps: 9217a98467 (ACPI / hotplug / PCI: Use global PCI rescan-remove locking)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to the changelog of commit 29ed1f29b6 (PCI: pciehp: Fix null
pointer deref when hot-removing SR-IOV device) it is unsafe to walk the
bus->devices list of a PCI bus and remove devices from it in direct order,
because that may lead to NULL pointer dereferences related to virtual
functions.
For this reason, change all of the bus->devices list walks in
acpiphp_glue.c during which devices may be removed to be carried out in
reverse order.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Revert commit ef83b0781a "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible. For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).
Moreover, the problem that commit ef83b0781a attempted to address
cannot happen any more after commit 8a4c5c329d "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.
Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit ef83b0781a from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.
Fixes: ef83b0781a (PCI: Remove from bus_list and release resources in pci_release_dev())
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
- FIFO event channels. Key advantages: support for over 100,000 events (2^17),
16 different event priorities, improved fairness in event latency through
the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with paravirtualized
disk and network, paravirtualized interrupts and timers, no emulated devices
of any kind (and thus no qemu), no BIOS or legacy boot — but instead of
requiring PV MMU, it uses the HVM hardware extensions to virtualize the
pagetables, as well as system calls and other privileged operations."
(from "The Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS4BmLAAoJEFjIrFwIi8fJ4SAH/iNGESowgMhfW64vRA8pBWq+
NRJpUjYjjwmbxpwoNl6NPwn15cIXFyc3sMtvvrDD3taRDyko2RFuT+NTjpO05xPh
d/cRpRXpXERHoiFgPf/WTp7ONBDhvPtHG0+BzJKwgqEIOUYXdbhD+gEjaVlFJScS
CAY68OLmk7XYMSZBNzPfKNbSCyhVgZF7wpaimK9lxZBKsFRCDIq6jIyrAsC8epIL
6V/V4l2S6lk/uUeGB6ULphYeINjI2kkpbSfCd1vyenLfWpVscc2o8uWEYFcZMAxy
V4HpsoseuqrfdDqgPfud3VgogdISvbkCvDfW85rzfDP4MWxei2mVHFtJ/gSBV+g=
=ToNG
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from Konrad Rzeszutek Wilk:
"Two major features that Xen community is excited about:
The first is event channel scalability by David Vrabel - we switch
over from an two-level per-cpu bitmap of events (IRQs) - to an FIFO
queue with priorities. This lets us be able to handle more events,
have lower latency, and better scalability. Good stuff.
The other is PVH by Mukesh Rathor. In short, PV is a mode where the
kernel lets the hypervisor program page-tables, segments, etc. With
EPT/NPT capabilities in current processors, the overhead of doing this
in an HVM (Hardware Virtual Machine) container is much lower than the
hypervisor doing it for us.
In short we let a PV guest run without doing page-table, segment,
syscall, etc updates through the hypervisor - instead it is all done
within the guest container. It is a "hybrid" PV - hence the 'PVH'
name - a PV guest within an HVM container.
The major benefits are less code to deal with - for example we only
use one function from the the pv_mmu_ops (which has 39 function
calls); faster performance for syscall (no context switches into the
hypervisor); less traps on various operations; etc.
It is still being baked - the ABI is not yet set in stone. But it is
pretty awesome and we are excited about it.
Lastly, there are some changes to ARM code - you should get a simple
conflict which has been resolved in #linux-next.
In short, this pull has awesome features.
Features:
- FIFO event channels. Key advantages: support for over 100,000
events (2^17), 16 different event priorities, improved fairness in
event latency through the use of FIFOs.
- Xen PVH support. "It’s a fully PV kernel mode, running with
paravirtualized disk and network, paravirtualized interrupts and
timers, no emulated devices of any kind (and thus no qemu), no BIOS
or legacy boot — but instead of requiring PV MMU, it uses the HVM
hardware extensions to virtualize the pagetables, as well as system
calls and other privileged operations." (from "The
Paravirtualization Spectrum, Part 2: From poles to a spectrum")
Bug-fixes:
- Fixes in balloon driver (refactor and make it work under ARM)
- Allow xenfb to be used in HVM guests.
- Allow xen_platform_pci=0 to work properly.
- Refactors in event channels"
* tag 'stable/for-linus-3.14-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (52 commits)
xen/pvh: Set X86_CR0_WP and others in CR0 (v2)
MAINTAINERS: add git repository for Xen
xen/pvh: Use 'depend' instead of 'select'.
xen: delete new instances of __cpuinit usage
xen/fb: allow xenfb initialization for hvm guests
xen/evtchn_fifo: fix error return code in evtchn_fifo_setup()
xen-platform: fix error return code in platform_pci_init()
xen/pvh: remove duplicated include from enlighten.c
xen/pvh: Fix compile issues with xen_pvh_domain()
xen: Use dev_is_pci() to check whether it is pci device
xen/grant-table: Force to use v1 of grants.
xen/pvh: Support ParaVirtualized Hardware extensions (v3).
xen/pvh: Piggyback on PVHVM XenBus.
xen/pvh: Piggyback on PVHVM for grant driver (v4)
xen/grant: Implement an grant frame array struct (v3).
xen/grant-table: Refactor gnttab_init
xen/grants: Remove gnttab_max_grant_frames dependency on gnttab_init.
xen/pvh: Piggyback on PVHVM for event channels (v2)
xen/pvh: Update E820 to work with PVH (v2)
xen/pvh: Secondary VCPU bringup (non-bootup CPUs)
...
* pci/locking:
PCI: Check parent kobject in pci_destroy_dev()
xen/pcifront: Use global PCI rescan-remove locking
powerpc/eeh: Use global PCI rescan-remove locking
MPT / PCI: Use pci_stop_and_remove_bus_device_locked()
platform / x86: Use global PCI rescan-remove locking
PCI: hotplug: Use global PCI rescan-remove locking
pcmcia: Use global PCI rescan-remove locking
ACPI / hotplug / PCI: Use global PCI rescan-remove locking
ACPI / PCI: Use global PCI rescan-remove locking in PCI root hotplug
PCI: Add global pci_lock_rescan_remove()
If pci_stop_and_remove_bus_device() is run concurrently for a device and
its parent bridge via remove_callback(), both code paths attempt to acquire
pci_rescan_remove_lock. If the child device removal acquires it first,
there will be no problems. However, if the parent bridge removal acquires
it first, it will eventually execute pci_destroy_dev() for the child
device, but that device object will not be freed yet due to the reference
held by the concurrent child removal. Consequently, both
pci_stop_bus_device() and pci_remove_bus_device() will be executed for that
device unnecessarily and pci_destroy_dev() will see a corrupted list head
in that object. Moreover, an excess put_device() will be executed for that
device in that case which may lead to a use-after-free in the final
kobject_put() done by sysfs_schedule_callback_work().
To avoid that problem, make pci_destroy_dev() check if the device's parent
kobject is NULL, which only happens after device_del() has already run for
it. Make pci_destroy_dev() return immediately whithout doing anything in
that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple race conditions are possible between the Xen pcifront device
addition and removal and the generic PCI device addition and removal that
can be triggered via sysfs.
To avoid those race conditions make the Xen pcifront code use global PCI
rescan-remove locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When doing a function/slot/bus reset PCI grabs the device_lock for each
device to block things like suspend and driver probes, but call paths exist
where this lock may already be held. This creates an opportunity for
deadlock. For instance, vfio allows userspace to issue resets so long as
it owns the device(s). If a driver unbind .remove callback races with
userspace issuing a reset, we have a deadlock as userspace gets stuck
waiting on device_lock while another thread has device_lock and waits for
.remove to complete. To resolve this, we can make a version of the reset
interfaces which use trylock. With this, we can safely attempt a reset and
return error to userspace if there is contention.
[bhelgaas: the deadlock happens when A (userspace) has a file descriptor for
the device, and B waits in this path:
driver_detach
device_lock # take device_lock
__device_release_driver
pci_device_remove # pci_bus_type.remove
vfio_pci_remove # pci_driver .remove
vfio_del_group_dev
wait_event(vfio.release_q, !vfio_dev_present) # wait (holding device_lock)
Now B is stuck until A gives up the file descriptor. If A tries to acquire
device_lock for any reason, we deadlock because A is waiting for B to release
the lock, and B is waiting for A to release the file descriptor.]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple race conditions are possible between PCI hotplug and the generic
PCI bus rescan and device removal that can be triggered via sysfs.
To avoid those race conditions make PCI hotplug use global PCI
rescan-remove locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Multiple race conditions are possible between the ACPI-based PCI hotplug
(ACPIPHP) and the generic PCI bus rescan and device removal that can be
triggered via sysfs.
To avoid those race conditions make the ACPIPHP code use global PCI
rescan-remove locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are multiple PCI device addition and removal code paths that may be
run concurrently with the generic PCI bus rescan and device removal that
can be triggered via sysfs. If that happens, it may lead to multiple
different, potentially dangerous race conditions.
The most straightforward way to address those problems is to run
the code in question under the same lock that is used by the
generic rescan/remove code in pci-sysfs.c. To prepare for those
changes, move the definition of the global PCI remove/rescan lock
to probe.c and provide global wrappers, pci_lock_rescan_remove()
and pci_unlock_rescan_remove(), allowing drivers to manipulate
that lock. Also provide pci_stop_and_remove_bus_device_locked()
for the callers of pci_stop_and_remove_bus_device() who only need
to hold the rescan/remove lock around it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Consistently use the:
#ifdef CONFIG_PCI_FOO
int pci_foo(...);
#else
static inline int pci_foo(...) { return -1; }
#endif
pattern, instead of sometimes using "#ifndef CONFIG_PCI_FOO".
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/aer:
PCI/AER: Support ACPI HEST AER error sources for PCI domains other than 0
ACPICA: Add helper macros to extract bus/segment numbers from HEST table.
In the discussion for this set of patches [link below], Bjorn Helgaas
pointed out that the ACPI HEST AER error sources do not have the PCIe
segment number associated with the bus. I worked with the ACPI spec and
got this change to definition of the "Bus" field into the recently released
ACPI Spec 5.0a section 18.3.2.3-5:
Identifies the PCI Bus and Segment of the device. The Bus is encoded in
bits 0-7. For systems that expose multiple PCI segment groups, the
segment number is encoded in bits 8-23 and bits 24-31 must be zero. For
systems that do not expose multiple PCI segment groups, bits 8-31 must be
zero. If the GLOBAL flag is specified, this field is ignored.
This patch makes use of the new definition in the only place in the kernel
that uses the acpi_hest_aer_common's bus field.
This depends on 36f3615152 ("ACPICA: Add helper macros to extract
bus/segment numbers from HEST table.")
Link: http://lkml.kernel.org/r/1370542251-27387-1-git-send-email-betty.dall@hp.com
Signed-off-by: Betty Dall <betty.dall@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Using 'make namespacecheck' identify code which should be declared static.
Checked for users in other driver/archs as well. Compile tested only.
This stops exporting the following interfaces to modules:
pci_target_state()
pci_load_saved_state()
[bhelgaas: retained pci_find_next_ext_capability() and pci_cfg_space_size()]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This removes this unused and deprecated interface:
alloc_pci_dev()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts part of f46753c5e3 ("PCI: introduce pci_slot") and
d25b7c8d6b ("PCI: rename pci_update_slot_number to pci_renumber_slot"),
removing this interface:
pci_renumber_slot()
[bhelgaas: split to separate patch, add historical link from Alex]
Link: http://lkml.kernel.org/r/20081009043140.8678.44164.stgit@bob.kio
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Chiang <achiang@canonical.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts part of 3e1b16002a ("ACPI/PCI: PCIe ASPM _OSC support
capabilities called when root bridge added"), removing this interface:
pcie_aspm_enabled()
[bhelgaas: split to separate patch]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Andrew Patterson <andrew.patterson@hp.com>
My philosophy is unused code is dead code. And dead code is subject to bit
rot and is a likely source of bugs. Use it or lose it.
This reverts db5679437a ("PCI: add interface to set visible size of
VPD"), removing this interface:
pci_vpd_truncate()
[bhelgaas: split to separate patch, also remove prototype from pci.h]
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas