Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
DIV_ROUND_UP() is defined in kernel.h which was not included by
media-entity.h. Do exactly that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In the ISI driver it reads the config register to get original value,
then set the correct FRATE_DIV and YCC_SWAP_MODE directly. This will
cause some bits overlap.
So we need to clear these bits first, then set correct value. This patch
fix it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The supply list is needed by the platform driver, but not by the usb driver.
So this information belongs to the platform data and should not be hardcoded
in the subdevice driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The field isn't set when parsing the endpoint. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When CONFIG_OF is not defined the v4l2_of_parse_endpoint() function is
defined as a stub that returns -ENOSYS. Make the real function return an
integer as well to be able to differentiate between the two cases.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds ioctl helpers to the V4L2 mem-to-mem API, so we can avoid
several ioctl handlers in the mem-to-mem video node drivers that are simply
a pass-through to the v4l2_m2m_* calls. These helpers will only be useful
for drivers that use same mutex for both OUTPUT and CAPTURE queue, which
is the case for all currently in tree v4l2 m2m drivers. In order to use
the helpers the drivers are required to use struct v4l2_fh.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a very simplistic driver to utilize the CSI2A interface inside
the ISS subsystem in OMAP4, and dump the data to memory.
Check Documentation/video4linux/omap4_camera.txt for details.
This commit adds the driver core, registers definitions and
documentation.
Signed-off-by: Sergio Aguirre <sergio.a.aguirre@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently it is not possible for userspace to map a DMABUF exported buffer
with write permissions. This patch allows to also pass O_RDONLY/O_RDWR when
exporting the buffer, so that userspace may map it with write permissions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
The helper function is defined by a macro that is erroneously called
with the compose rectangle instead of the crop rectangle. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds the driver for the LM3560, dual LED Flash The LM3560 has two 1A
constant current driver for high current white LEDs.
It is controlled via an I2C compatible interface(up to 400kHz).
Each flash brightness, torch brightness and enable/disable can be
controlled independantly, but flash timeout and operation mode are shared.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some non soc-camera drivers, e.g. em28xx, use subdevice drivers, originally
written for soc-camera, which use soc_camera_power_on() and
soc_camera_power_off() helpers to implement their .s_power() methods. Those
helpers in turn can enable and disable a clock, if it is supplied to them
as a parameter. This works well when camera host drivers balance their
calls to subdevices' .s_power() methods. However, some such drivers fail to
do that, which leads to unbalanced calls to v4l2_clk_enable() /
v4l2_clk_disable(), which then in turn produce kernel warnings. Such
behaviour is wrong and should be fixed, however, sometimes it is difficult,
because some of those drivers are rather old and use lots of subdevices,
which all should be tested after such a fix. To support such drivers this
patch adds a work-around, allowing host drivers or platforms to set a flag,
in which case soc-camera helpers will only enable the clock, if it is
disabled, and disable it only once on the first call to .s_power(0).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To obtain a clock reference consumers supply their device object to the
V4L2 clock framework. The latter then uses the consumer device name to
find a matching clock. For that to work V4L2 clock providers have to
provide the same device name, when registering clocks. This patch adds
a helper macro to generate a suitable device name for I2C devices.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Many bridges and video host controllers supply fixed rate always on clocks
to their I2C devices. This patch adds two simple helpers to register and
unregister such a clock.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This prepares soc-camera to use struct v4l2_subdev_platform_data for its
subdevice-facing API, which would allow subdevice driver re-use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This struct shall be used by subdevice drivers to pass per-subdevice data,
e.g. power supplies, to generic V4L2 methods, at the same time allowing
optional host-specific extensions via the host_priv pointer. To avoid
having to pass two pointers to those methods, add a pointer to this new
struct to struct v4l2_subdev.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
BUG*() and WARN*() macros specify their conditions as unlikely, using
BUG_ON(unlikely(condition)) is redundant, remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
struct v4l2_fh has an enum v4l2_priority field. Make sure the enum
definition is available by including linux/videodev2.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-fh.h dereferences struct file, the structure must thus be defined.
Pull in its definition by including linux/fs.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the redundant 'const' qualifiers from the function
signature and from the qmenu_int arrays' declarations.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace the private struct vb2_dma_sg_desc with the struct sg_table so
we can benefit from all the helping functions in lib/scatterlist.c for
things like allocating the sg or compacting the descriptor.
marvel-ccic and solo6x10 drivers, that use this API have been updated.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[s.nawrocki@samsung.com: minor corrections of the changelog]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
struct v4_file_operations defines the data param as
const char __user *data but on vb2 is defined as
char __user *data.
This patch fixes the warnings produced by this. ie:
drivers/qtec/qtec_xform.c:817:2: warning: initialization from
incompatible pointer type [enabled by default]
drivers/qtec/qtec_xform.c:817:2: warning: (near initialization for
‘qtec_xform_v4l_fops.write’) [enabled by default]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
This patch fixes following error:
include/media/v4l2-ctrls.h:193:15: error: field ‘_lock’ has incomplete type
include/media/v4l2-ctrls.h: In function ‘v4l2_ctrl_lock’:
include/media/v4l2-ctrls.h:570:2: error: implicit declaration of
function ‘mutex_lock’ [-Werror=implicit-function-declaration]
include/media/v4l2-ctrls.h: In function ‘v4l2_ctrl_unlock’:
include/media/v4l2-ctrls.h:579:2: error: implicit declaration of
function ‘mutex_unlock’ [-Werror=implicit-function-declaration]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: stable@vger.kernel.org
This is an Analog Devices HDMI transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is a Analog Devices Component/Graphics/SD Digitizer with 2:1
Multiplexed HDMI Receiver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In most cases the v4l2_bt_timings_cap struct has all the information
necessary to determine valid timings, but occasionally there are exceptions.
Add a callback function to be able to test for those exceptions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All other functions follow the v4l2_<foo>_dv_timings pattern, do the same for
this function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some drivers need to be able to access the full list of timings.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's the only function in v4l2-dv-timings.c with the v4l prefix instead
of v4l2. Make it consistent with the other functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drivers often have to log the contents of a dv_timings struct. Adding
this helper will make it easier for drivers to do so.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the clock framework makes it possible to assign a device specific name to
the clocks, remove the ability to use a named clock in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Configure the device external clock using the common clock framework
instead of a board code callback function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset d1e9b7c12 added a new ancilliary function to API, but forgot
to add it to the corresponding header file.
drivers/media/v4l2-core/v4l2-ctrls.c:568:18: warning: no previous prototype for 'v4l2_ctrl_get_int_menu' [-Wmissing-prototypes]
const s64 const *v4l2_ctrl_get_int_menu(u32 id, u32 *len)
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset 2ccf12a did a crappy job when added multi-line comment lines,
violating CodingStyle.
Change the comments added there to fulfill CodingStyle, and document
the platform_data using Documentation/kernel-doc-nano-HOWTO.txt.
Cc: Jon Arne Jørgensen <jonarne@jonarne.no>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch implements i2c_board_info.platform_data, and some options to
override the default initialization table for the GM7113C and SAA7113
chips.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-common.c contained a bunch of dv-timings related functions.
Move that to the new v4l2-dv-timings.c which is a more appropriate
place for them.
There aren't many drivers that do HDTV, so it is a good idea to separate
common code related to that into a module of its own.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This module makes it easy to filter valid timings from the full list of
CEA and DMT timings based on the timings capabilities.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move include/sound/tea575x-tuner.h to include/media/tea575x.h and update files that include it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Explain how the two operations must handle formats and validate buffer
sizes when used with VIDIOC_CREATE_BUFS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The graph traversal API (media_entity_graph_walk_*) doesn't support
cyclic graphs and will fail to correctly walk a graph when circular
links exist. Support circular graph traversal by checking whether an
entity has already been visited before pushing it to the stack.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's convenient to have ethernet mac addresses use
ETH_ALEN to be able to grep for them a bit easier and
also to ensure that the addresses are __aligned(2).
Add #include <linux/if_ether.h> as necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use case is simple, if any rc device has allowed protocols =
RC_TYPE_LIRC and map_name = RC_MAP_LIRC set, the driver open will be never
called. The reason for this is, all of the key maps except lirc have some
KEYS in there map, so during rc_register_device process these keys are
matched against the input drivers and open is performed, so for the case
of RC_MAP_EMPTY, a vt/keyboard is matched and the driver open is
performed.
In case of lirc, there is no match and result is that there is no open
performed, however the lirc-dev will go ahead and create a /dev/lirc0
node. Now when lircd/mode2 opens this device, no data is available
because the driver was never opened.
Other case pointed by Sean Young, As rc device gets opened via the
input interface. If the input device is never opened (e.g. embedded with
no console) then the rc open is never called and lirc will not work
either. So that's another case.
lirc_dev seems to have no link with actual rc device w.r.t open/close.
This patch adds rc_dev pointer to lirc_driver structure for cases like
this, so that it can do the open/close of the real driver in accordance
to lircd/mode2 open/close.
Without this patch its impossible to open a rc device which has
RC_TYPE_LIRC ad RC_MAP_LIRC set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds user count to rc_dev structure, the reason to add this
new member is to allow other code like lirc to open rc device directly.
In the existing code, rc device is only opened by input subsystem which
works ok if we have any input drivers to match. But in case like lirc
where there will be no input driver, rc device will be never opened.
Having this user count variable will be usefull to allow rc device to be
opened from code other than rc-main.
This patch also adds rc_open and rc_close functions for other drivers
like lirc to open and close rc devices. This functions safely increment
and decrement the user count. Other driver wanting to open rc device
should call rc_open and rc_close, rather than directly modifying the
rc_dev structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
By integrating the v4l2-async API internals a bit more with
the core overall the v4l2-async code becomes a bit simpler
and easier to follow.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is a purely cosmetic change. Since the 'subdev' member
points to an array of subdevs make it more explicit by
renaming to the plural form.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for matching by device_node pointer. This allows
the notifier user to simply pass a list of device_node pointers
corresponding to sub-devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
enum v4l2_async_bus_type also selects a method subdevs are matched
in the notification handlers, rename it to v4l2_async_match_type
so V4L2_ASYNC_MATCH_OF entry can be further added for matching by
device tree node pointer.
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch makes the platform data members as array wherever
possible, so as this makes easier while collecting the data
in DT case and read the entire array at once.
This patch also makes appropriate changes to board-da850-evm.c
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes following error:
include/media/v4l2-ctrls.h:193:15: error: field ‘_lock’ has incomplete type
include/media/v4l2-ctrls.h: In function ‘v4l2_ctrl_lock’:
include/media/v4l2-ctrls.h:570:2: error: implicit declaration of
function ‘mutex_lock’ [-Werror=implicit-function-declaration]
include/media/v4l2-ctrls.h: In function ‘v4l2_ctrl_unlock’:
include/media/v4l2-ctrls.h:579:2: error: implicit declaration of
function ‘mutex_unlock’ [-Werror=implicit-function-declaration]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On mem2mem decoders with a hardware bitstream ringbuffer, to drain the
buffer at the end of the stream, remaining frames might need to be decoded
from the bitstream buffer without additional input buffers being provided.
To achieve this, allow a queue to be marked as buffered by the driver, and
allow scheduling of device_runs when buffered ready queues are empty.
This also allows a driver to copy input buffers into their bitstream
ringbuffer and immediately mark them as done to be dequeued.
The motivation for this patch is hardware assisted h.264 reordering support
in the coda driver. For high profile streams, the coda can hold back
out-of-order frames, causing a few mem2mem device runs in the beginning, that
don't produce any decompressed buffer at the v4l2 capture side. At the same
time, the last few frames can be decoded from the bitstream with mem2mem device
runs that don't need a new input buffer at the v4l2 output side. The decoder
command ioctl can be used to put the decoder into the ringbuffer draining
end-of-stream mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ensure the colorspace is properly adjusted by the driver for YUV
and Bayer image formats. The subdev try_fmt helper is simplified.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In scan_async_group() if the size parameter is negative, the sasd pointer
will be used uninitialised:
drivers/media/platform/soc_camera/soc_camera.c: In function "soc_camera_host_register":
drivers/media/platform/soc_camera/soc_camera.c:1514:55: warning: "sasd" may
be used uninitialized in this function [-Wmaybe-uninitialized]
sasd->asd.match.i2c.adapter_id, sasd->asd.match.i2c.address);
^
drivers/media/platform/soc_camera/soc_camera.c:1464:34: note: "sasd" was
declared here
struct soc_camera_async_subdev *sasd;
Fix this by making "size" and the array, from which it is assigned unsigned.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the v4l2-async API to support asynchronous subdevice probing,
including the CSI2 subdevice. Synchronous probing is still supported too.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for asynchronous subdevice probing, using the v4l2-async API.
The legacy synchronous mode is still supported too, which allows to
gradually update drivers and platforms. The selected approach adds a
notifier for each struct soc_camera_device instance, i.e. for each video
device node, even when there are multiple such instances registered with a
single soc-camera host simultaneously.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of centrally enabling and disabling subdevice master clocks in
soc-camera core, let subdevice drivers do that themselves, using the
V4L2 clock API and soc-camera convenience wrappers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently bridge device drivers register devices for all subdevices
synchronously, typically, during their probing. E.g. if an I2C CMOS sensor
is attached to a video bridge device, the bridge driver will create an I2C
device and wait for the respective I2C driver to probe. This makes linking
of devices straight forward, but this approach cannot be used with
intrinsically asynchronous and unordered device registration systems like
the Flattened Device Tree. To support such systems this patch adds an
asynchronous subdevice registration framework to V4L2. To use it respective
(e.g. I2C) subdevice drivers must register themselves with the framework.
A bridge driver on the other hand must register notification callbacks,
that will be called upon various related events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is often useful to have simple means to get from a subdevice to the
underlying physical device. This patch adds such a pointer to struct
v4l2_subdev and sets it accordingly in the I2C and SPI cases.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Typical video devices like camera sensors require an external clock source.
Many such devices cannot even access their hardware registers without a
running clock. These clock sources should be controlled by their consumers.
This should be performed, using the generic clock framework. Unfortunately
so far only very few systems have been ported to that framework. This patch
adds a set of temporary helpers, mimicking the generic clock API, to V4L2.
Platforms, adopting the clock API, should switch to using it. Eventually
this temporary API should be removed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera uses a single camera host callback to activate the
interface master clock and to configure the interface for a specific
client. However, during probing we might not have the information about
a client, we just need to activate the clock. Add new camera host driver
callbacks to only start and stop the clock without and client-specific
configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All soc-camera host drivers include a pointer to an soc-camera device in
their host private struct to check, that only one client is connected.
Move this common code to soc_camera.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The last set of drivers still using the parent field of video_device instead
of the v4l2_dev field have been converted, so v4l2_dev is now always set.
A proper pointer to v4l2_dev is necessary these days otherwise the advanced
debugging ioctls will not work when addressing sub-devices. It also ensures
that the core can always go from a video_device struct to the top-level
v4l2_device struct.
There is still one single use case for the parent pointer: if there are
multiple busses, each being the parent of one or more video nodes, and if
they all share the same v4l2_device struct. In that case one still needs a
parent pointer since the v4l2_device struct can only refer to a single
parent device. The cx88 driver is one such case. Unfortunately, the cx88
failed to set the parent pointer since 3.6. The next patch will correct this.
In order to support this use-case the parent pointer is only renamed to
dev_parent, not removed altogether. It has been renamed to ensure that the
compiler will catch any (possibly out-of-tree) drivers that were missed during
the conversion.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The parent field will eventually disappear to be replaced by v4l2_dev.
soc_camera does provide a v4l2_device struct but did not point to it in
struct video_device. This is now fixed.
Now the video nodes can be found under the correct platform bus, and
the advanced debug ioctls work correctly as well (the core implementation
of those ioctls requires that v4l2_dev is set correctly).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has been replaced by the new and much better VIDIOC_DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function is no longer needed since it is now the responsibility of the
v4l2 core to check if the DBG_G/S_REGISTER and DBG_G_CHIP_INFO ioctls are
called for the bridge driver or not.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus: (1465 commits)
ARM: tegra30: clocks: Fix pciex clock registration
lseek(fd, n, SEEK_END) does *not* go to eof - n
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
sctp: fully initialize sctp_outq in sctp_outq_init
netiucv: Hold rtnl between name allocation and device registration.
...
This function allows to remove all media entity's links to other
entities, leaving no references to a media entity's links array
at its remote entities.
Currently, when a driver of some entity is removed it will free its
media entities links[] array, leaving dangling pointers at other
entities that are part of same media graph. This is troublesome when
drivers of a media device entities are in separate kernel modules,
removing only some modules will leave others in an incorrect state.
This function is intended to be used when an entity is being
unregistered from a media device.
With an assumption that normally the media links should be created
between media entities registered to a media device, with the graph
mutex held.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
"Series of fixes for 3.10. There are some usual driver fixes (mostly
on s5p/exynos playform drivers), plus some fixes at V4L2 core"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (40 commits)
[media] soc_camera: error dev remove and v4l2 call
[media] sh_veu: fix the buffer size calculation
[media] sh_veu: keep power supply until the m2m context is released
[media] sh_veu: invoke v4l2_m2m_job_finish() even if a job has been aborted
[media] v4l2-ioctl: don't print the clips list
[media] v4l2-ctrls: V4L2_CTRL_CLASS_FM_RX controls are also valid radio controls
[media] cx88: fix NULL pointer dereference
[media] DocBook/media/v4l: update version number
[media] exynos4-is: Remove "sysreg" clock handling
[media] exynos4-is: Fix reported colorspace at FIMC-IS-ISP subdev
[media] exynos4-is: Ensure fimc-is clocks are not enabled until properly configured
[media] exynos4-is: Prevent NULL pointer dereference when firmware isn't loaded
[media] s5p-mfc: Add NULL check for allocated buffer
[media] s5p-mfc: added missing end-of-lines in debug messages
[media] s5p-mfc: v4l2 controls setup routine moved to initialization code
[media] s5p-mfc: separate encoder parameters for h264 and mpeg4
[media] s5p-mfc: Remove special clock usage in driver
[media] s5p-mfc: Remove unused s5p_mfc_get_decoded_status_v6() function
[media] v4l2: mem2mem: save irq flags correctly
[media] coda: v4l2-compliance fix: add VIDIOC_CREATE_BUFS support
...
The use of current_norm to keep track of the current standard has been
deprecated for quite some time. Now that all drivers that were using it
have been converted to use g_std we can drop it from the core.
It was a bad idea to introduce this at the time: since it is a per-device
node field it didn't work for drivers that create multiple nodes, all sharing
the same tuner (e.g. video and vbi nodes, or a raw video node and a compressed
video node). In addition it was very surprising behavior that g_std was
implemented in the core. Often drivers implemented both g_std and current_norm,
because they didn't understand how it should be used.
Since the benefits were very limited (if they were there at all), it is better
to just drop it and require that drivers just implement g_std.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace the V4L2_IDENT_* usage with tveeprom-specific defines. This header
is deprecated, so those defines shouldn't be used anymore.
The em28xx driver is the only one that uses the tveeprom audio_processor
field, so that has been updated to use the new tveeprom AUDPROC define.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes init_enable option from pdata, the init_enable
was intended that the device should start streaming video immediately
but ideally the bridge drivers should call s_stream explicitly for such
devices to start video.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the media device link_notify callback is invoked before the
actual change of state of a link when the link is being enabled, and
after the actual change of state when the link is being disabled.
This doesn't allow a media device driver to perform any operations
on a full graph before a link is disabled, as well as performing
any tasks on a modified graph right after a link's state is changed.
This patch modifies signature of the link_notify callback. This
callback is now called always before and after a link's state change.
To distinguish the notifications a 'notification' argument is added
to the link_notify callback: MEDIA_DEV_NOTIFY_PRE_LINK_CH indicates
notification before link's state change and
MEDIA_DEV_NOTIFY_POST_LINK_CH corresponds to a notification after
link flags change.
[mchehab@redhat.com: whitespace cleanups]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This enumeration is now private to exynos4-is and the exynos5 camera
subsystem driver may have the subdevs handling designed differently.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces common structure for the video entities
to handle all video nodes and media pipelines associated with
them in more generic way.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function media_entity_remote_source actually returns the remote pad to
the given one, regardless if this is the source or the sink pad.
Name media_entity_remote_pad is more adequate for this function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch rearranges the description of field members of
struct tvp7002_config. Also as the all the fields where accepting
a value either 0/1, made the members as bool.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a code that (auto)detects gm7113c clones. The auto-detection
here is not perfect, as, on contrary to what it would be expected
by looking into its datasheets some devices would return, instead:
saa7115 0-0025: chip 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 @ 0x4a is unknown
(found on a device labeled as GM7113C 1145 by Ezequiel Garcia)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enables tvp7002 decoder driver for media controller
based usage by adding v4l2_subdev_pad_ops operations support
for enum_mbus_code, set_pad_format, get_pad_format and media_entity_init()
on probe and media_entity_cleanup() on remove.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the keytable for the remote that comes with the Delock 61959.
NEC protocol with address 0x866b.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull omap3isp clk support from Mauro Carvalho Chehab:
"This patch were sent in separate as it depends on a merge from clock
framework, that you merged in commit 362ed48dee50"
* 'topic/omap3isp' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Use the common clock framework
videobuf_queue_dma_contig_init_cached() is not used anywhere.
Drop support for it, cleaning up the code a little bit.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
[mchehab@redhat.com: change it to depends on MFD_SI476X_CORE instead of
selecting it; vidioc_s_register now uses const struct]
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is very similar than rc-msi-digivox-iii but new keytable is needed
as there is one existing scancode mapped to different button. Also that
one has less buttons.
NEC extended protocol with address 0x61d6.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Expose the two ISP external clocks XCLKA and XCLKB as common clocks for
subdev drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl will be extended to return more information than just the name.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only enable this ioctl if the VIDEO_ADV_DEBUG config option is set. This
prevents abuse from both userspace and kernelspace (some bridge drivers
abuse DBG_G_CHIP_IDENT, lets prevent that from happening again with this
ioctl).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Configure the device external clock using the common clock framework
instead of a board code callback function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the sub-device group ID definitions to the driver's public header
so they are available to other media drivers that need to share modules
found in exynos4-is.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
config looks like a hack that was added to tuner-core to allow some
configuration of TDA8290 tuner (it's not used by any other driver).
But with the new configuration options of tda8290 driver (no_i2c_gate
and std_map), it's no longer sufficient.
Change config to be void * instead, which allows passing tuner-dependent
config struct to drivers.
Also update saa7134 driver to reflect this change (no other driver uses this).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FIMC-LITE output DMA allows to configure different YUV order
than the order at the camera input interface. Thus there is some
limited colorspace conversion possible. This patch makes the
color format variable be per FIMC-LITE input/output, rather than
a global per device. This also fixes incorrect behavior where
color format at the FIMC-LITE.N subdev's source pad is modified
by VIDIOC_S_FMT ioctl on the related video node.
YUV order definitions are corrected so that we use notation:
| byte3 | byte2 | byte1 | byte0
-------+-------+-------+-------+------
YCBYCR | CR | Y | CB | Y
YCRYCB | CB | Y | CR | Y
CBYCRY | Y | CR | Y | CB
CRYCBY | Y | CB | Y | CR
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_of_parse_parallel_bus() function is now static and
EXPORT_SYMBOL() doesn't apply to it any more. Drop this
meaningless statement, which was supposed to be done in
the original merged patch.
While at it, edit the copyright notice so it is sorted in
both the v4l2-of.c and v4l2-of.h file in newest entries
on top order, and state clearly I'm just the author of
parts of the code, not the copyright owner.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on work done by Katsuya Matsubara.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop fimc-lite.h header inclusion to make the exynos-fimc-lite
module independent on other modules. Move struct fimc_fmt
declaration to the driver's private headers as it is used in
multiple modules.
Reported-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor (I2C and/or SPI client) devices are instantiated by their
corresponding control bus drivers. Since the I2C client's master clock
is often provided by a video bus receiver (host interface) or other
than I2C/SPI controller device, the drivers of those client devices
are not accessing hardware in their driver's probe() callback. Instead,
after enabling clock, the host driver calls back into a sub-device
when it wants to activate them. This pattern is used by some in-tree
drivers and this patch also uses it for DT case. This patch is intended
as a first step for adding device tree support to the S5P/Exynos SoC
camera drivers. The second one is adding support for asynchronous
sub-devices registration and clock control from sub-device driver
level. The bindings shall not change when asynchronous probing support
is added.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds changes required for the main camera media device
driver corresponding to the top level 'camera' device node.
The drivers of devices corresponding to child nodes of the 'camera'
node are looked up and and registered as sub-devices to the top
level driver. The main driver's probing is deferred if any of the
sub-device drivers is not yet initialized and ready.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch support for binding the driver to the MIPI-CSIS
devices instantiated from device tree and parsing the SoC
and board specific properties. The MIPI CSI-2 channel is
determined by the value of reg property placed in csis'
port subnode.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a V4L2 OF parser, implementing bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt.
[s.nawrocki@samsung.com: various corrections and improvements
since the initial version]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplify the debugging ioctls by creating the VIDIOC_DBG_G_CHIP_NAME ioctl.
This will eventually replace VIDIOC_DBG_G_CHIP_IDENT. Chip matching is done
by the name or index of subdevices or an index to a bridge chip. Most of this
can all be done automatically, so most drivers just need to provide get/set
register ops.
In particular, it is now possible to get/set subdev registers without
requiring assistance of the bridge driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These ioctls are no longer used by any drivers, so remove them.
[mchehab@redhat.com: Fix merge conflict]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These ops are no longer used, so it's time to remove them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's no longer used, so it can now be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This based on the wis-uda1342.c driver that's part of the go7007 driver.
It has been converted to a v4l subdev driver by Pete Eberlein, and I made
additional cleanups.
Based on work by: Pete Eberlein <pete@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for three Sony BTF tuners:
TUNER_SONY_BTF_PG472Z: PAL+SECAM
TUNER_SONY_BTF_PK467Z: NTSC-M-JP
TUNER_SONY_BTF_PB463Z: NTSC-M
These come from the go7007 staging driver where they were implemented in
the wis-sony-tuner i2c driver.
Adding support for these tuners to tuner-types.c is the first step towards
removing the wis-sony-tuner driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices expect a double rate ASCLK. Add a flag to let the driver know
through the s_crystal_freq call.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Needed by the go7007 driver: it assumes a different polarity of the IDQ
signal, so we need to be able to tell the saa7115 about this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a v4l2_subdev_has_op() macro and a v4l2_device_has_op macro to
quickly check if a specific subdev or any subdev supports a particular subdev
operation.
This makes it easy for drivers to disable certain ioctls if none of the subdevs
supports the necessary functionality.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When calling v4l2_ctrl_add_handler(), lockdep would detect a potential
recursive locking problem on a situation that is by design intended and
not a recursive lock. This happened because all struct
v4l2_ctrl_handler.lock mutexes were created as members of the same lock
class in v4l2_ctrl_handler_init(), and v4l2_ctrl_add_handler() takes the
hdl->lock on two different v4l2_ctrl_handler instances.
This change breaks the large lockdep lock class for struct
v4l2_ctrl_handler.lock and breaks it into v4l2_ctrl_handler
instantiation specific lock classes with meaningful class names.
This will validly eliminate lockdep alarms for v4l2_ctrl_handler locking
validation, as long as the relationships between drivers adding v4l2
controls to their own handler from other v4l2 drivers' control handlers
remains straightforward.
struct v4l2_ctrl_handler.lock lock classes are created with names such
that the output of cat /proc/lockdep indicates where in the v4l2 driver
code v4l2_ctrl_handle_init() is being called on instantiations:
ffffffffa045f490 FD: 10 BD: 8 +.+...: cx2341x:1534:(hdl)->lock
ffffffffa0497d20 FD: 12 BD: 2 +.+.+.: saa7115:1581:(hdl)->lock
ffffffffa04ac660 FD: 14 BD: 2 +.+.+.: msp3400_driver:756:(hdl)->lock
ffffffffa0484b90 FD: 12 BD: 1 +.+.+.: ivtv_gpio:366:(&itv->hdl_gpio)->lock
ffffffffa04eb530 FD: 11 BD: 2 +.+.+.: cx25840_core:1982:(&state->hdl)->lock
ffffffffa04fbc80 FD: 11 BD: 3 +.+.+.: wm8775:246:(&state->hdl)->lock
Some lock chains, that were previously causing the recursion alarms, are
now visible in the output of cat /proc/lockdep_chains:
irq_context: 0
[ffffffffa0497d20] saa7115:1581:(hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa04ac660] msp3400_driver:756:(hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa0484b90] ivtv_gpio:366:(&itv->hdl_gpio)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa04eb530] cx25840_core:1982:(&state->hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa04fbc80] wm8775:246:(&state->hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
[hans.verkuil@cisco.com: keep mutex_init in v4l2_ctrl_handler_init_class]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument by value instead of by
reference. I could have chosen to add const instead, but this is 1) easier
to handle in drivers and 2) consistent with the s_std subdev operation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl is defined as IOW, so pass the argument as const.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
store_protocols() treats dev->rc_map.rc_type as a bitmap which is wrong for
two reasons. First of all, it is pretty bogus to change the protocol type of
the keymap just because the hardware has been asked to decode a different
protocol.
Second, dev->rc_map.rc_type is an enum (i.e. a single protocol) as pointed
out by James Hogan <james.hogan@imgtec.com>.
Fix both issues by introducing a separate enabled_protocols member to
struct rc_dev.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch adds support for THS7353 video amplifier.
The the THS7353 amplifier is very much similar to the
existing THS7303 video amplifier driver.
This patch appropriately makes changes to the existing
ths7303 driver and adds support for the THS7353.
This patch also adds V4L2_IDENT_THS7353 for the THS7353
chip and appropriate changes to Kconfig file for building.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some drivers have special memory requirements for their buffers, usually
related to DMA (e.g. GFP_DMA or __GFP_DMA32). Make it possible to specify
additional GFP flags for those buffers by adding a gfp_flags field to
vb2_queue.
Note that this field will be replaced in the future with a different
mechanism, but that is still work in progress and we need this feature
now so we won't be able to convert drivers with such requirements to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/davinci/dm644x_ccdc.c: In function ‘validate_ccdc_param’:
drivers/media/platform/davinci/dm644x_ccdc.c:233:32: warning: comparison between ‘enum ccdc_gama_width’ and ‘enum ccdc_data_size’ [-Wenum-compare]
It took a bit of work, see this thread of an earlier attempt to fix this:
https://patchwork.kernel.org/patch/1923091/
I've chosen not to follow the suggestions in that thread since gamma_width is
really a different property from data_size. What you really want is to know if
gamma_width fits inside data_size and for that you need to translate each
enum into a maximum bit number so you can safely compare the two.
So I put in two static inline translation functions instead, keeping the rest
of the code the same (except for fixing the 'gama' typo).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove VPBE_ENC_DV_PRESET (the DV_PRESET API is no longer supported) and
VPBE_ENC_CUSTOM_TIMINGS is renamed to VPBE_ENC_DV_TIMINGS since the old
"CUSTOM_TIMINGS" name is deprecated in favor of "DV_TIMINGS".
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Not all drivers use monotonic timestamps. This patch adds a way to set the
timestamp type per every queue.
In addition, set proper timestamp type in drivers that I am sure that use
either MONOTONIC or COPY timestamps. Other drivers will correctly report
UNKNOWN timestamp type instead of assuming that all drivers use monotonic
timestamps.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a prerequisite for the G/S_REGISTER ioctls.
In addition, add support to call G/S_REGISTER for supporting i2c devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some bridge drivers capture pixels during blanking periods if
pixclk is enabled. In order to avoid capturing bogus data we need to
disable pixclk in the sensor during those blanking periods.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For a frame rate of 30 fps a pixclk of 24MHz is needed. For those
cases where the ov7670 has a clean 24MHz input (xvclk) the PLL
can be bypassed.
This will result in a value of clkrc of 1, which means that in practice
pixclk = xvclk (input clock)
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark current frame as error frame when ppi error interrupt
report fifo error. Member next_frm in struct bcap_device can
be optimized out.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the field description of fields that no
longer exists, along side aligns the field description of
fields.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was implemented with some default configurations,
this default configuration works on board and doesn't work on other.
This patch accepts the configuration through platform data and configures
the encoder depending on the data passed.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer Exynos4 SoC are equipped with a local camera ISP that
controls external raw image sensor directly. Such sensors
can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to
the ISP, which then feeds image data to the FIMCn IP. Thus
there can be two busses associated with an image source
(sensor). Rename struct s5p_fimc_isp_info describing external
image sensor (video decoder) to struct fimc_source_info to
avoid confusion. bus_type is split into fimc_bus_type and
sensor_bus_type. The bus type enumeration is extended to
include both FIMC Writeback input types.
The bus_type enumeration and the data structure name in the
board files are modified according to the above changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Martin Bugge