Use rethook for kretprobe function return hooking if the arch sets
CONFIG_HAVE_RETHOOK=y. In this case, CONFIG_KRETPROBE_ON_RETHOOK is
set to 'y' automatically, and the kretprobe internal data fields
switches to use rethook. If not, it continues to use kretprobe
specific function return hooks.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/164826162556.2455864.12255833167233452047.stgit@devnote2
In order to allow kprobes to skip the ENDBR instructions at sym+0 for
X86_KERNEL_IBT builds, change _kprobe_addr() to take an architecture
callback to inspect the function at hand and modify the offset if
needed.
This streamlines the existing interface to cover more cases and
require less hooks. Once PowerPC gets fully converted there will only
be the one arch hook.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154318.405947704@infradead.org
Currently a lot of ftrace code assumes __fentry__ is at sym+0. However
with Intel IBT enabled the first instruction of a function will most
likely be ENDBR.
Change ftrace_location() to not only return the __fentry__ location
when called for the __fentry__ location, but also when called for the
sym+0 location.
Then audit/update all callsites of this function to consistently use
these new semantics.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20220308154318.227581603@infradead.org
kernel/sysctl.c is a kitchen sink where everyone leaves their dirty
dishes, this makes it very difficult to maintain.
To help with this maintenance let's start by moving sysctls to places
where they actually belong. The proc sysctl maintainers do not want to
know what sysctl knobs you wish to add for your own piece of code, we
just care about the core logic.
Move sysctl_kprobes_optimization from kernel/sysctl.c to
kernel/kprobes.c. Use register_sysctl() to register the sysctl
interface.
[mcgrof@kernel.org: fix compile issue when CONFIG_OPTPROBES is disabled]
Link: https://lkml.kernel.org/r/20211129211943.640266-7-mcgrof@kernel.org
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Lukas Middendorf <kernel@tuxforce.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Stephen Kitt <steve@sk2.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: f47cd9b553 ("kprobes: kretprobe user entry-handler")
Reported-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
- kprobes: Restructured stack unwinder to show properly on x86 when a stack
dump happens from a kretprobe callback.
- Fix to bootconfig parsing
- Have tracefs allow owner and group permissions by default (only denying
others). There's been pressure to allow non root to tracefs in a
controlled fashion, and using groups is probably the safest.
- Bootconfig memory managament updates.
- Bootconfig clean up to have the tools directory be less dependent on
changes in the kernel tree.
- Allow perf to be traced by function tracer.
- Rewrite of function graph tracer to be a callback from the function tracer
instead of having its own trampoline (this change will happen on an arch
by arch basis, and currently only x86_64 implements it).
- Allow multiple direct trampolines (bpf hooks to functions) be batched
together in one synchronization.
- Allow histogram triggers to add variables that can perform calculations
against the event's fields.
- Use the linker to determine architecture callbacks from the ftrace
trampoline to allow for proper parameter prototypes and prevent warnings
from the compiler.
- Extend histogram triggers to key off of variables.
- Have trace recursion use bit magic to determine preempt context over if
branches.
- Have trace recursion disable preemption as all use cases do anyway.
- Added testing for verification of tracing utilities.
- Various small clean ups and fixes.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYYBdxhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qp1sAQD2oYFwaG3sx872gj/myBcHIBSKdiki
Hry5csd8zYDBpgD+Poylopt5JIbeDuoYw/BedgEXmscZ8Qr7VzjAXdnv/Q4=
=Loz8
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- kprobes: Restructured stack unwinder to show properly on x86 when a
stack dump happens from a kretprobe callback.
- Fix to bootconfig parsing
- Have tracefs allow owner and group permissions by default (only
denying others). There's been pressure to allow non root to tracefs
in a controlled fashion, and using groups is probably the safest.
- Bootconfig memory managament updates.
- Bootconfig clean up to have the tools directory be less dependent on
changes in the kernel tree.
- Allow perf to be traced by function tracer.
- Rewrite of function graph tracer to be a callback from the function
tracer instead of having its own trampoline (this change will happen
on an arch by arch basis, and currently only x86_64 implements it).
- Allow multiple direct trampolines (bpf hooks to functions) be batched
together in one synchronization.
- Allow histogram triggers to add variables that can perform
calculations against the event's fields.
- Use the linker to determine architecture callbacks from the ftrace
trampoline to allow for proper parameter prototypes and prevent
warnings from the compiler.
- Extend histogram triggers to key off of variables.
- Have trace recursion use bit magic to determine preempt context over
if branches.
- Have trace recursion disable preemption as all use cases do anyway.
- Added testing for verification of tracing utilities.
- Various small clean ups and fixes.
* tag 'trace-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (101 commits)
tracing/histogram: Fix semicolon.cocci warnings
tracing/histogram: Fix documentation inline emphasis warning
tracing: Increase PERF_MAX_TRACE_SIZE to handle Sentinel1 and docker together
tracing: Show size of requested perf buffer
bootconfig: Initialize ret in xbc_parse_tree()
ftrace: do CPU checking after preemption disabled
ftrace: disable preemption when recursion locked
tracing/histogram: Document expression arithmetic and constants
tracing/histogram: Optimize division by a power of 2
tracing/histogram: Covert expr to const if both operands are constants
tracing/histogram: Simplify handling of .sym-offset in expressions
tracing: Fix operator precedence for hist triggers expression
tracing: Add division and multiplication support for hist triggers
tracing: Add support for creating hist trigger variables from literal
selftests/ftrace: Stop tracing while reading the trace file by default
MAINTAINERS: Update KPROBES and TRACING entries
test_kprobes: Move it from kernel/ to lib/
docs, kprobes: Remove invalid URL and add new reference
samples/kretprobes: Fix return value if register_kretprobe() failed
lib/bootconfig: Fix the xbc_get_info kerneldoc
...
This converts the kprobes testcases to use the kunit framework.
It adds a dependency on CONFIG_KUNIT, and the output will change
to TAP:
TAP version 14
1..1
# Subtest: kprobes_test
1..4
random: crng init done
ok 1 - test_kprobe
ok 2 - test_kprobes
ok 3 - test_kretprobe
ok 4 - test_kretprobes
ok 1 - kprobes_test
Note that the kprobes testcases are no longer run immediately after
kprobes initialization, but as a late initcall when kunit is
initialized. kprobes itself is initialized with an early initcall,
so the order is still correct.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Doing cleanups in the tail of schedule() is a latency punishment for the
incoming task. The point of invoking kprobes_task_flush() for a dead task
is that the instances are returned and cannot leak when __schedule() is
kprobed.
Move it into the delayed cleanup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210928122411.537994026@linutronix.de
In x86, the fake return address on the stack saved by
__kretprobe_trampoline() will be replaced with the real return
address after returning from trampoline_handler(). Before fixing
the return address, the real return address can be found in the
'current->kretprobe_instances'.
However, since there is a window between updating the
'current->kretprobe_instances' and fixing the address on the stack,
if an interrupt happens at that timing and the interrupt handler
does stacktrace, it may fail to unwind because it can not get
the correct return address from 'current->kretprobe_instances'.
This will eliminate that window by fixing the return address
right before updating 'current->kretprobe_instances'.
Link: https://lkml.kernel.org/r/163163057094.489837.9044470370440745866.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since the ORC unwinder from pt_regs requires setting up regs->ip
correctly, set the correct return address to the regs->ip before
calling user kretprobe handler.
This allows the kretrprobe handler to trace stack from the
kretprobe's pt_regs by stack_trace_save_regs() (eBPF will do
this), instead of stack tracing from the handler context by
stack_trace_save() (ftrace will do this).
Link: https://lkml.kernel.org/r/163163053237.489837.4272653874525136832.stgit@devnote2
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Introduce kretprobe_find_ret_addr() and is_kretprobe_trampoline().
These APIs will be used by the ORC stack unwinder and ftrace, so that
they can check whether the given address points kretprobe trampoline
code and query the correct return address in that case.
Link: https://lkml.kernel.org/r/163163046461.489837.1044778356430293962.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The __kretprobe_trampoline_handler() callback, called from low level
arch kprobes methods, has the 'trampoline_address' parameter, which is
entirely superfluous as it basically just replicates:
dereference_kernel_function_descriptor(kretprobe_trampoline)
In fact we had bugs in arch code where it wasn't replicated correctly.
So remove this superfluous parameter and use kretprobe_trampoline_addr()
instead.
Link: https://lkml.kernel.org/r/163163044546.489837.13505751885476015002.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
~15 years ago kprobes grew the 'arch_deref_entry_point()' __weak function:
3d7e33825d87: ("jprobes: make jprobes a little safer for users")
But this is just open-coded dereference_symbol_descriptor() in essence, and
its obscure nature was causing bugs.
Just use the real thing and remove arch_deref_entry_point().
Link: https://lkml.kernel.org/r/163163043630.489837.7924988885652708696.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Use the 'bool' type instead of 'int' for the functions which
returns a boolean value, because this makes clear that those
functions don't return any error code.
Link: https://lkml.kernel.org/r/163163041649.489837.17311187321419747536.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since get_optimized_kprobe() is only used inside kprobes,
it doesn't need to use 'unsigned long' type for 'addr' parameter.
Make it use 'kprobe_opcode_t *' for the 'addr' parameter and
subsequent call of arch_within_optimized_kprobe() also should use
'kprobe_opcode_t *'.
Note that MAX_OPTIMIZED_LENGTH and RELATIVEJUMP_SIZE are defined
by byte-size, but the size of 'kprobe_opcode_t' depends on the
architecture. Therefore, we must be careful when calculating
addresses using those macros.
Link: https://lkml.kernel.org/r/163163040680.489837.12133032364499833736.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix coding style issues reported by checkpatch.pl and update
comments to quote variable names and add "()" to function
name.
One TODO comment in __disarm_kprobe() is removed because
it has been done by following commit.
Link: https://lkml.kernel.org/r/163163037468.489837.4282347782492003960.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This clean up the error/notification messages in kprobes related code.
Basically this defines 'pr_fmt()' macros for each files and update
the messages which describes
- what happened,
- what is the kernel going to do or not do,
- is the kernel fine,
- what can the user do about it.
Also, if the message is not needed (e.g. the function returns unique
error code, or other error message is already shown.) remove it,
and replace the message with WARN_*() macros if suitable.
Link: https://lkml.kernel.org/r/163163036568.489837.14085396178727185469.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
arch_check_ftrace_location() was introduced as a weak function in
commit f7f242ff00 ("kprobes: introduce weak
arch_check_ftrace_location() helper function") to allow architectures
to handle kprobes call site on their own.
Recently, the only architecture (csky) to implement
arch_check_ftrace_location() was migrated to using the common
version.
As a result, further cleanup the code to drop the weak attribute and
rename the function to remove the architecture specific
implementation.
Link: https://lkml.kernel.org/r/163163035673.489837.2367816318195254104.stgit@devnote2
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The function prepare_kprobe() is called during kprobe registration and
is responsible for ensuring any architecture related preparation for
the kprobe is done before returning.
One of two versions of prepare_kprobe() is chosen depending on the
availability of KPROBE_ON_FTRACE in the kernel configuration.
Simplify the code by dropping the version when KPROBE_ON_FTRACE is not
selected - instead relying on kprobe_ftrace() to return false when
KPROBE_ON_FTRACE is not set.
No functional change.
Link: https://lkml.kernel.org/r/163163033696.489837.9264661820279300788.stgit@devnote2
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The "enabled" file provides a debugfs interface to arm / disarm
kprobes in the kernel. In order to parse the buffer containing the
values written from userspace, the callback manually parses the user
input to convert it to a boolean value.
As taking a string value from userspace and converting it to boolean
is a common operation, a helper kstrtobool_from_user() is already
available in the kernel. Update the callback to use the common helper
to parse the write buffer from userspace.
Link: https://lkml.kernel.org/r/163163032637.489837.10678039554832855327.stgit@devnote2
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
debugfs_create_file() takes a pointer argument that can be used during
file operation callbacks (accessible via i_private in the inode
structure). An obvious requirement is for the pointer to refer to
valid memory when used.
When creating the debugfs file to dynamically enable / disable
kprobes, a pointer to local variable is passed to
debugfs_create_file(); which will go out of scope when the init
function returns. The reason this hasn't triggered random memory
corruption is because the pointer is not accessed during the debugfs
file callbacks.
Since the enabled state is managed by the kprobes_all_disabled global
variable, the local variable is not needed. Fix the incorrect (and
unnecessary) usage of local variable during debugfs_file_create() by
passing NULL instead.
Link: https://lkml.kernel.org/r/163163031686.489837.4476867635937014973.stgit@devnote2
Fixes: bf8f6e5b3e ("Kprobes: The ON/OFF knob thru debugfs")
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Restore two hunks from commit:
6333e8f73b ("static_call: Avoid kprobes on inline static_call()s")
that went walkabout in a Git merge commit.
Fixes: 76d4acf22b ("Merge tag 'perf-kprobes-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20210628113045.167127609@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- A big series refactoring parts of our KVM code, and converting some to C.
- Support for ARCH_HAS_SET_MEMORY, and ARCH_HAS_STRICT_MODULE_RWX on some CPUs.
- Support for the Microwatt soft-core.
- Optimisations to our interrupt return path on 64-bit.
- Support for userspace access to the NX GZIP accelerator on PowerVM on Power10.
- Enable KUAP and KUEP by default on 32-bit Book3S CPUs.
- Other smaller features, fixes & cleanups.
Thanks to: Andy Shevchenko, Aneesh Kumar K.V, Arnd Bergmann, Athira Rajeev, Baokun Li,
Benjamin Herrenschmidt, Bharata B Rao, Christophe Leroy, Daniel Axtens, Daniel Henrique
Barboza, Finn Thain, Geoff Levand, Haren Myneni, Jason Wang, Jiapeng Chong, Joel Stanley,
Jordan Niethe, Kajol Jain, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas
Piggin, Nick Desaulniers, Paul Mackerras, Russell Currey, Sathvika Vasireddy, Shaokun
Zhang, Stephen Rothwell, Sudeep Holla, Suraj Jitindar Singh, Tom Rix, Vaibhav Jain,
YueHaibing, Zhang Jianhua, Zhen Lei.
-----BEGIN PGP SIGNATURE-----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=zo4d
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- A big series refactoring parts of our KVM code, and converting some
to C.
- Support for ARCH_HAS_SET_MEMORY, and ARCH_HAS_STRICT_MODULE_RWX on
some CPUs.
- Support for the Microwatt soft-core.
- Optimisations to our interrupt return path on 64-bit.
- Support for userspace access to the NX GZIP accelerator on PowerVM on
Power10.
- Enable KUAP and KUEP by default on 32-bit Book3S CPUs.
- Other smaller features, fixes & cleanups.
Thanks to: Andy Shevchenko, Aneesh Kumar K.V, Arnd Bergmann, Athira
Rajeev, Baokun Li, Benjamin Herrenschmidt, Bharata B Rao, Christophe
Leroy, Daniel Axtens, Daniel Henrique Barboza, Finn Thain, Geoff Levand,
Haren Myneni, Jason Wang, Jiapeng Chong, Joel Stanley, Jordan Niethe,
Kajol Jain, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas
Piggin, Nick Desaulniers, Paul Mackerras, Russell Currey, Sathvika
Vasireddy, Shaokun Zhang, Stephen Rothwell, Sudeep Holla, Suraj Jitindar
Singh, Tom Rix, Vaibhav Jain, YueHaibing, Zhang Jianhua, and Zhen Lei.
* tag 'powerpc-5.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (218 commits)
powerpc: Only build restart_table.c for 64s
powerpc/64s: move ret_from_fork etc above __end_soft_masked
powerpc/64s/interrupt: clean up interrupt return labels
powerpc/64/interrupt: add missing kprobe annotations on interrupt exit symbols
powerpc/64: enable MSR[EE] in irq replay pt_regs
powerpc/64s/interrupt: preserve regs->softe for NMI interrupts
powerpc/64s: add a table of implicit soft-masked addresses
powerpc/64e: remove implicit soft-masking and interrupt exit restart logic
powerpc/64e: fix CONFIG_RELOCATABLE build warnings
powerpc/64s: fix hash page fault interrupt handler
powerpc/4xx: Fix setup_kuep() on SMP
powerpc/32s: Fix setup_{kuap/kuep}() on SMP
powerpc/interrupt: Use names in check_return_regs_valid()
powerpc/interrupt: Also use exit_must_hard_disable() on PPC32
powerpc/sysfs: Replace sizeof(arr)/sizeof(arr[0]) with ARRAY_SIZE
powerpc/ptrace: Refactor regs_set_return_{msr/ip}
powerpc/ptrace: Move set_return_regs_changed() before regs_set_return_{msr/ip}
powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()
powerpc/pseries/vas: Include irqdomain.h
powerpc: mark local variables around longjmp as volatile
...
Merge more updates from Andrew Morton:
"190 patches.
Subsystems affected by this patch series: mm (hugetlb, userfaultfd,
vmscan, kconfig, proc, z3fold, zbud, ras, mempolicy, memblock,
migration, thp, nommu, kconfig, madvise, memory-hotplug, zswap,
zsmalloc, zram, cleanups, kfence, and hmm), procfs, sysctl, misc,
core-kernel, lib, lz4, checkpatch, init, kprobes, nilfs2, hfs,
signals, exec, kcov, selftests, compress/decompress, and ipc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
ipc/util.c: use binary search for max_idx
ipc/sem.c: use READ_ONCE()/WRITE_ONCE() for use_global_lock
ipc: use kmalloc for msg_queue and shmid_kernel
ipc sem: use kvmalloc for sem_undo allocation
lib/decompressors: remove set but not used variabled 'level'
selftests/vm/pkeys: exercise x86 XSAVE init state
selftests/vm/pkeys: refill shadow register after implicit kernel write
selftests/vm/pkeys: handle negative sys_pkey_alloc() return code
selftests/vm/pkeys: fix alloc_random_pkey() to make it really, really random
kcov: add __no_sanitize_coverage to fix noinstr for all architectures
exec: remove checks in __register_bimfmt()
x86: signal: don't do sas_ss_reset() until we are certain that sigframe won't be abandoned
hfsplus: report create_date to kstat.btime
hfsplus: remove unnecessary oom message
nilfs2: remove redundant continue statement in a while-loop
kprobes: remove duplicated strong free_insn_page in x86 and s390
init: print out unknown kernel parameters
checkpatch: do not complain about positive return values starting with EPOLL
checkpatch: improve the indented label test
checkpatch: scripts/spdxcheck.py now requires python3
...
free_insn_page() in x86 and s390 is same with the common weak function in
kernel/kprobes.c. Plus, the comment "Recover page to RW mode before
releasing it" in x86 seems insensible to be there since resetting mapping
is done by common code in vfree() of module_memfree(). So drop these two
duplicated strong functions and related comment, then mark the common one
in kernel/kprobes.c strong.
Link: https://lkml.kernel.org/r/20210608065736.32656-1-song.bao.hua@hisilicon.com
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: "Naveen N. Rao" <naveen.n.rao@linux.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reason for kprobe::fault_handler(), as given by their comment:
* We come here because instructions in the pre/post
* handler caused the page_fault, this could happen
* if handler tries to access user space by
* copy_from_user(), get_user() etc. Let the
* user-specified handler try to fix it first.
Is just plain bad. Those other handlers are ran from non-preemptible
context and had better use _nofault() functions. Also, there is no
upstream usage of this.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20210525073213.561116662@infradead.org
Some architectures like powerpc require a non standard
allocation of optinsn page, because module pages are
too far from the kernel for direct branches.
Define weak alloc_optinsn_page() and free_optinsn_page(), that
fall back on alloc_insn_page() and free_insn_page() when not
overridden by the architecture.
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/40a43d6df1fdf41ade36e9a46e60a4df774ca9f6.1620896780.git.christophe.leroy@csgroup.eu
Commit 36dadef23f ("kprobes: Init kprobes in early_initcall")
moved the kprobe setup in early_initcall(), which includes kprobe
jump optimization.
The kprobes jump optimizer involves synchronize_rcu_tasks() which
depends on the ksoftirqd and rcu_spawn_tasks_*(). However, since
those are setup in core_initcall(), kprobes jump optimizer can not
run at the early_initcall().
To avoid this issue, make the kprobe optimization disabled in the
early_initcall() and enables it in subsys_initcall().
Note that non-optimized kprobes is still available after
early_initcall(). Only jump optimization is delayed.
Link: https://lkml.kernel.org/r/161365856280.719838.12423085451287256713.stgit@devnote2
Fixes: 36dadef23f ("kprobes: Init kprobes in early_initcall")
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: RCU <rcu@vger.kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Neeraj Upadhyay <neeraju@codeaurora.org>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: "Theodore Y . Ts'o" <tytso@mit.edu>
Cc: Oleksiy Avramchenko <oleksiy.avramchenko@sonymobile.com>
Cc: stable@vger.kernel.org
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Uladzislau Rezki <urezki@gmail.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Warn if the kprobe is reregistered, since there must be
a software bug (actively used resource must not be re-registered)
and caller must be fixed.
Link: https://lkml.kernel.org/r/161236436734.194052.4058506306336814476.stgit@devnote2
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.ibm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Our system encountered a re-init error when re-registering same kretprobe,
where the kretprobe_instance in rp->free_instances is illegally accessed
after re-init.
Implementation to avoid re-registration has been introduced for kprobe
before, but lags for register_kretprobe(). We must check if kprobe has
been re-registered before re-initializing kretprobe, otherwise it will
destroy the data struct of kretprobe registered, which can lead to memory
leak, system crash, also some unexpected behaviors.
We use check_kprobe_rereg() to check if kprobe has been re-registered
before running register_kretprobe()'s body, for giving a warning message
and terminate registration process.
Link: https://lkml.kernel.org/r/20210128124427.2031088-1-bobo.shaobowang@huawei.com
Cc: stable@vger.kernel.org
Fixes: 1f0ab40976 ("kprobes: Prevent re-registration of the same kprobe")
[ The above commit should have been done for kretprobes too ]
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Cheng Jian <cj.chengjian@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix kprobe_on_func_entry() returns error code instead of false so that
register_kretprobe() can return an appropriate error code.
append_trace_kprobe() expects the kprobe registration returns -ENOENT
when the target symbol is not found, and it checks whether the target
module is unloaded or not. If the target module doesn't exist, it
defers to probe the target symbol until the module is loaded.
However, since register_kretprobe() returns -EINVAL instead of -ENOENT
in that case, it always fail on putting the kretprobe event on unloaded
modules. e.g.
Kprobe event:
/sys/kernel/debug/tracing # echo p xfs:xfs_end_io >> kprobe_events
[ 16.515574] trace_kprobe: This probe might be able to register after target module is loaded. Continue.
Kretprobe event: (p -> r)
/sys/kernel/debug/tracing # echo r xfs:xfs_end_io >> kprobe_events
sh: write error: Invalid argument
/sys/kernel/debug/tracing # cat error_log
[ 41.122514] trace_kprobe: error: Failed to register probe event
Command: r xfs:xfs_end_io
^
To fix this bug, change kprobe_on_func_entry() to detect symbol lookup
failure and return -ENOENT in that case. Otherwise it returns -EINVAL
or 0 (succeeded, given address is on the entry).
Link: https://lkml.kernel.org/r/161176187132.1067016.8118042342894378981.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: 59158ec4ae ("tracing/kprobes: Check the probe on unloaded module correctly")
Reported-by: Jianlin Lv <Jianlin.Lv@arm.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The kretprobe hash is mostly superfluous, replace it with a per-task
variable.
This gets rid of the task hash and it's related locking.
Note that this may change the kprobes module-exported API for kretprobe
handlers. If any out-of-tree kretprobe user uses ri->rp, use
get_kretprobe(ri) instead.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/159870620431.1229682.16325792502413731312.stgit@devnote2
Init kprobes feature in early_initcall as same as jump_label and
dynamic_debug does, so that we can use kprobes events in earlier
boot stage.
Link: https://lkml.kernel.org/r/159974151897.478751.8342374158615496628.stgit@devnote2
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since kprobe_event= cmdline option allows user to put kprobes on the
functions in initmem, kprobe has to make such probes gone after boot.
Currently the probes on the init functions in modules will be handled
by module callback, but the kernel init text isn't handled.
Without this, kprobes may access non-exist text area to disable or
remove it.
Link: https://lkml.kernel.org/r/159972810544.428528.1839307531600646955.stgit@devnote2
Fixes: 970988e19e ("tracing/kprobe: Add kprobe_event= boot parameter")
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Commit:
0cb2f1372b ("kprobes: Fix NULL pointer dereference at kprobe_ftrace_handler")
fixed one bug but the underlying bugs are not completely fixed yet.
If we run a kprobe_module.tc of ftracetest, a warning triggers:
# ./ftracetest test.d/kprobe/kprobe_module.tc
=== Ftrace unit tests ===
[1] Kprobe dynamic event - probing module
...
------------[ cut here ]------------
Failed to disarm kprobe-ftrace at trace_printk_irq_work+0x0/0x7e [trace_printk] (-2)
WARNING: CPU: 7 PID: 200 at kernel/kprobes.c:1091 __disarm_kprobe_ftrace.isra.0+0x7e/0xa0
This is because the kill_kprobe() calls disarm_kprobe_ftrace() even
if the given probe is not enabled. In that case, ftrace_set_filter_ip()
fails because the given probe point is not registered to ftrace.
Fix to check the given (going) probe is enabled before invoking
disarm_kprobe_ftrace().
Fixes: 0cb2f1372b ("kprobes: Fix NULL pointer dereference at kprobe_ftrace_handler")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/159888672694.1411785.5987998076694782591.stgit@devnote2
Free kretprobe_instance with RCU callback instead of directly
freeing the object in the kretprobe handler context.
This will make kretprobe run safer in NMI context.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/159870616685.1229682.11978742048709542226.stgit@devnote2
The in_nmi() check in pre_handler_kretprobe() is meant to avoid
recursion, and blindly assumes that anything NMI is recursive.
However, since commit:
9b38cc704e ("kretprobe: Prevent triggering kretprobe from within kprobe_flush_task")
there is a better way to detect and avoid actual recursion.
By setting a dummy kprobe, any actual exceptions will terminate early
(by trying to handle the dummy kprobe), and recursion will not happen.
Employ this to avoid the kretprobe_table_lock() recursion, replacing
the over-eager in_nmi() check.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/159870615628.1229682.6087311596892125907.stgit@devnote2
Add a generic kretprobe trampoline handler for unifying
the all cloned /arch/* kretprobe trampoline handlers.
The generic kretprobe trampoline handler is based on the
x86 implementation, because it is the latest implementation.
It has frame pointer checking, kprobe_busy_begin/end and
return address fixup for user handlers.
[ mingo: Minor edits. ]
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/159870600138.1229682.3424065380448088833.stgit@devnote2
- The biggest news in that the tracing ring buffer can now time events that
interrupted other ring buffer events. Before this change, if an interrupt
came in while recording another event, and that interrupt also had an
event, those events would all have the same time stamp as the event it
interrupted. Now, with the new design, those events will have a unique time
stamp and rightfully display the time for those events that were recorded
while interrupting another event.
- Bootconfig how has an "override" operator that lets the users have a
default config, but then add options to override the default.
- A fix was made to properly filter function graph tracing to the ftrace
PIDs. This came in at the end of the -rc cycle, and needs to be backported.
- Several clean ups, performance updates, and minor fixes as well.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXy3GOBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qphsAP9ci1jtrC2+cMBMCNKb/AFpA/nDaKsD
hpsDzvD0YPOmCAEA9QbZset8wUNG49R4FexP7egQ8Ad2S6Oa5f60jWleDQY=
=lH+q
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- The biggest news in that the tracing ring buffer can now time events
that interrupted other ring buffer events.
Before this change, if an interrupt came in while recording another
event, and that interrupt also had an event, those events would all
have the same time stamp as the event it interrupted.
Now, with the new design, those events will have a unique time stamp
and rightfully display the time for those events that were recorded
while interrupting another event.
- Bootconfig how has an "override" operator that lets the users have a
default config, but then add options to override the default.
- A fix was made to properly filter function graph tracing to the
ftrace PIDs. This came in at the end of the -rc cycle, and needs to
be backported.
- Several clean ups, performance updates, and minor fixes as well.
* tag 'trace-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (39 commits)
tracing: Add trace_array_init_printk() to initialize instance trace_printk() buffers
kprobes: Fix compiler warning for !CONFIG_KPROBES_ON_FTRACE
tracing: Use trace_sched_process_free() instead of exit() for pid tracing
bootconfig: Fix to find the initargs correctly
Documentation: bootconfig: Add bootconfig override operator
tools/bootconfig: Add testcases for value override operator
lib/bootconfig: Add override operator support
kprobes: Remove show_registers() function prototype
tracing/uprobe: Remove dead code in trace_uprobe_register()
kprobes: Fix NULL pointer dereference at kprobe_ftrace_handler
ftrace: Fix ftrace_trace_task return value
tracepoint: Use __used attribute definitions from compiler_attributes.h
tracepoint: Mark __tracepoint_string's __used
trace : Have tracing buffer info use kvzalloc instead of kzalloc
tracing: Remove outdated comment in stack handling
ftrace: Do not let direct or IPMODIFY ftrace_ops be added to module and set trampolines
ftrace: Setup correct FTRACE_FL_REGS flags for module
tracing/hwlat: Honor the tracing_cpumask
tracing/hwlat: Drop the duplicate assignment in start_kthread()
tracing: Save one trace_event->type by using __TRACE_LAST_TYPE
...
We found a case of kernel panic on our server. The stack trace is as
follows(omit some irrelevant information):
BUG: kernel NULL pointer dereference, address: 0000000000000080
RIP: 0010:kprobe_ftrace_handler+0x5e/0xe0
RSP: 0018:ffffb512c6550998 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8e9d16eea018 RCX: 0000000000000000
RDX: ffffffffbe1179c0 RSI: ffffffffc0535564 RDI: ffffffffc0534ec0
RBP: ffffffffc0534ec1 R08: ffff8e9d1bbb0f00 R09: 0000000000000004
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff8e9d1f797060 R14: 000000000000bacc R15: ffff8e9ce13eca00
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000080 CR3: 00000008453d0005 CR4: 00000000003606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
ftrace_ops_assist_func+0x56/0xe0
ftrace_call+0x5/0x34
tcpa_statistic_send+0x5/0x130 [ttcp_engine]
The tcpa_statistic_send is the function being kprobed. After analysis,
the root cause is that the fourth parameter regs of kprobe_ftrace_handler
is NULL. Why regs is NULL? We use the crash tool to analyze the kdump.
crash> dis tcpa_statistic_send -r
<tcpa_statistic_send>: callq 0xffffffffbd8018c0 <ftrace_caller>
The tcpa_statistic_send calls ftrace_caller instead of ftrace_regs_caller.
So it is reasonable that the fourth parameter regs of kprobe_ftrace_handler
is NULL. In theory, we should call the ftrace_regs_caller instead of the
ftrace_caller. After in-depth analysis, we found a reproducible path.
Writing a simple kernel module which starts a periodic timer. The
timer's handler is named 'kprobe_test_timer_handler'. The module
name is kprobe_test.ko.
1) insmod kprobe_test.ko
2) bpftrace -e 'kretprobe:kprobe_test_timer_handler {}'
3) echo 0 > /proc/sys/kernel/ftrace_enabled
4) rmmod kprobe_test
5) stop step 2) kprobe
6) insmod kprobe_test.ko
7) bpftrace -e 'kretprobe:kprobe_test_timer_handler {}'
We mark the kprobe as GONE but not disarm the kprobe in the step 4).
The step 5) also do not disarm the kprobe when unregister kprobe. So
we do not remove the ip from the filter. In this case, when the module
loads again in the step 6), we will replace the code to ftrace_caller
via the ftrace_module_enable(). When we register kprobe again, we will
not replace ftrace_caller to ftrace_regs_caller because the ftrace is
disabled in the step 3). So the step 7) will trigger kernel panic. Fix
this problem by disarming the kprobe when the module is going away.
Link: https://lkml.kernel.org/r/20200728064536.24405-1-songmuchun@bytedance.com
Cc: stable@vger.kernel.org
Fixes: ae6aa16fdc ("kprobes: introduce ftrace based optimization")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Co-developed-by: Chengming Zhou <zhouchengming@bytedance.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Since we already lock both kprobe_mutex and text_mutex in the optimizer,
text will not be changed and the module unloading will be stopped
inside kprobes_module_callback().
The mutex_lock() has originally been introduced to avoid conflict with text modification,
at that point we didn't hold text_mutex.
But after:
f1c6ece237 ("kprobes: Fix potential deadlock in kprobe_optimizer()")
We started holding the text_mutex and don't need the modules mutex anyway.
So remove the module_mutex locking.
[ mingo: Amended the changelog. ]
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Link: https://lore.kernel.org/r/20200728163400.e00b09c594763349f99ce6cb@kernel.org
The kprobe show() functions were using "current"'s creds instead
of the file opener's creds for kallsyms visibility. Fix to use
seq_file->file->f_cred.
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 81365a947d ("kprobes: Show address of kprobes if kallsyms does")
Fixes: ffb9bd68eb ("kprobes: Show blacklist addresses as same as kallsyms does")
Signed-off-by: Kees Cook <keescook@chromium.org>
Masami Hiramatsu