On OMAP4 platform audio has separate IC, it is no longer part
of the pmic chip.
Prevent twl-core to claim the 0x4b address, which belongs to
the twl6040 audio IC.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since a structure device is available now, use the dev_ macros instead
of the pr_ ones.
Clean some badly formatted comments.
Remove some unused variables.
Move some variable to the place they belong.
Clean some badly wrapped lines.
Align variable definition
Add missing braces in if-then-else block.
Add blank line for better readability.
Move stuff here and there...
Conflicts:
drivers/mfd/twl-core.c
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl4030 is using a two level irq controllers infrastruture.
So far, only the first level was using dynamic irq_desc allocation
to be able to have irq_domain support for device tree.
There is a need to allocate separate irq_descs for the SIH too to
avoid hacking the first level with interrupts from the second level.
Add an irq_base parameter to allow the caller to provide the base from
pdata or from dynamic allocation.
Affect TWL4030_NR_IRQS to the twl-core IRQs only.
Moreover that will allow the extraction of the of_node pointer for further
Device Tree conversion.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During DT adaptation, the irq_alloc_desc was added into twl-core, but
due to the rather different and weird IRQ management required by the twl4030,
it is much better to have a different approach for it.
The issue is that twl4030 uses a two level IRQ mechanism but handles all the
PWR interrupts as part of the twl-core interrupt range. It ends up with a
range of 16 interrupts total for CORE and PWR.
The other twl4030 functionalities already have a dedicated driver and thus
their IRQs and irqdomain can and should be defined localy.
twl6030 is using a single level IRQ controller and thus does not require any
trick.
Move the irq_alloc_desc and irq_domain_add_legacy in twl4030-irq and
twl6030-irq.
Allocate together CORE and PWR IRQs for twl4030-irq.
Conflicts:
drivers/mfd/twl-core.c
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The twl-core exported functions are already declared in twl-core.h
Include the header file instead or re-declaring the functions.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver doesn't really need <plat/cpu.h>, so remove it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With sparse IRQs the driver shouldn't depend at all on
any IRQ values coming from board-file.
Remove every occurences of pdata->irq_base/end.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Card detect IRQ from the TWL6030 used to be provided to the MMC
controller code using a statically allocated IRQ scheme:
card_detect_irq = TWL6030_IRQ_BASE + MMCDETECT_INTR_OFFSET;
This is no longer valid in a SPARSE_IRQ context since there is no more
pre-defined TWL6030_IRQ_BASE.
Return the proper card detect IRQ value in the twl6030_mmc_card_detect_config
that will be called from the MMC controller.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65090 is a Texas Instrument PMIC. It contains 3 Step-Down converters, 2
always on LDO's and 7 current limited load switches.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
da9052_i2c_remove() can and should be marked as __devexit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixing build error reported by Stephen Rothwell:
drivers/built-in.o: In function `rc5t583_i2c_init':
rc5t583.c:(.init.text+0xb3db): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `rc5t583_i2c_probe':
rc5t583.c:(.devinit.text+0x8fa0): undefined reference to `regmap_init_i2c'
drivers/built-in.o: In function `rc5t583_i2c_exit':
rc5t583.c:(.exit.text+0x708): undefined reference to `i2c_del_driver'
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Rob Lee <rob.lee@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch removes the obsolete hwacc implementation in the
DB8500 PRCMU driver.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use DIV_ROUND_CLOSEST to replace sm501fb_round_div function.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ricoh power management IC RC5T583 contains is multi
functional device having multiple sub devices inside this.
This device has multiple dcdc/ldo regulators, gpios, interrupt
controllers, on-key, RTCs, ADCs.
This device have 4 DCDCs, 8 LDOs, 8 GPIOs, 6 ADCs, 3 RTCs etc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch updates the AB8500 driver to make use of the I2C
read-modify-write service in the PRCMU firmware.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds driver support for the I2C read-modify-write
service in the U8500 PRCMU firmware.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This builds upon the changes done to support AB9540 so as
also to support the AB8505 derivative of the AB8500
circuit.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This disadvantage of having it interruptible is that it would
appear to work OK in most situations, but in the rare case
that this call does fail, it can lead to misconfiguration
of the AB, such as a regulator not being turned off and
leading to a platform power consumption increase.
There's no real benefit to having this interruptible.
Make it a plain mutex_lock. The non-interruptability matches
other low-level I/O functions such as SPI and I2C.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was the copy-paste issue in reg cache support code where
variable name for regmap config was not really starting from
the device name, it was starting from some other device name.
Fixing this so that variable name contains actual device name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some volatile registers accidentally had defaults added, though there were
no harmful side effects other than increased memory consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to check if the other core is in WFI
mode. It is the last check the idle routine has to do before
entering into the retention state.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to check if there are some pending irqs
on the prcmu.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the case we go to the retention mode, we decoupled the gic
in order to have the A9 core to reach a stable WFI state.
But we want the prcmu to wake up the A9 when the gic has a pending
irq which is done by copying the gic settings to the to the prcmu.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch introduces a routine to check if there are some
irqs pending on the gic. Usually this check is not relevant because
it appears racy (an irq can arrive right after this check), but in
the ux500 it makes sense because the prcmu decouples the gic from
the A9 cores.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
I missed in my previous patch the A9_MASK_REQ[_MASK] were
already defined. Let's remove the duplicate definitions.
The PRCMU_GIC_DELAY macro could be removed as it is not
really useful here.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Also remove a redundant semicolon from return statement.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since several sub modules such as backlight, leds and vibrator depend
on the refernce group and internal oscillator in pm8606, so modified
the power control of led in pm8606 by unified interface.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since several sub modules such as backlight, leds and vibrator depend
on the refernce group and internal oscillator in pm8606, so modified
the power control of backlight in pm8606 by unified interface.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Collect all the sub-devices of pm8606 initialization into
device_pm8606_init() for code clean up.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The reference group and internal oscillator are shared by sub-devs
like led, backlight and vibrator in PM8606 chip. Now introduce a
voting mechanism to enable/disable it.
Add pm8606_osc_enable() and pm8606_osc_disable() interface and
related defines to support this. This interface will be called by
vibrator led and backlight driver.The refernce group and internal
oscillator are enabled only when at least one of it's clients holds
it on or disabled only all the clients don't use it any more based
on the above mechanism.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Hai Dong <hai.dong@polycom.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Include linux/mfd/pcf50633/mbc.h instead of duplicating the same defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Include linux/mfd/pcf50633/pmic.h instead of duplicating the same defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It should be marked as readable but wasn't, breaking DC servo operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using regmap apis for accessing the device registers and
using RBTREE caching mechanims for caching registers.
Enabling caching of the registers which is used for voltage
controls. By doing this, the modify_bits operation is faster as
it does not involve the i2c register read from device, just read
from cache. This results faster set voltage operation.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For 88pm860x pmic, it can wake the system from low power mode by irq,
its sub-devs like RTC and onkey can be enabled for this usage.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6030_irq_set_wake is not used anywhere else in the kernel
except as irq_chip.irq_set_wake. No reason for it to be exported.
Also fixes build warning:
drivers/mfd/twl6030-irq.c:230:5: warning: symbol 'twl6030_irq_set_wake' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6030 family of PMIC use a shadow interrupt status register
while kernel processes the current interrupt event.
However, any write(0 or 1) to register INT_STS_A, INT_STS_B or
INT_STS_C clears all 3 interrupt status registers.
Since clear of the interrupt is done on 32k clk, depending on I2C
bus speed, we could in-adverently clear the status of a interrupt
status pending on shadow register in the current implementation.
This is due to the fact that multi-byte i2c write operation into
three seperate status register could result in multiple load
and clear of status and result in lost interrupts.
Instead, doing a single byte write to INT_STS_A register with 0x0
will clear all three interrupt status registers without the related
risk.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
da9052 has been converted to use regmap API, so we can remove the unused
io_lock mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to decouple and recouple the gic from the PRCMU.
This is needed to put the A9 core in retention mode with the cpuidle
driver.
It is based on top of the "DB8500 PRCMU update" patchset.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_base of the tps65912 irq platform data should be
initialized with the board provided irq_base data.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The code is currently always checking the first resource of every
device only (several times.) This has been broken since the ACPI check
was added in February 2010 in commit
91fedede03.
Fix the check to run on each resource individually, once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes warnings and needed for correctness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Peter Ujfalusi