On platforms that don't always enable CONFIG_GPIOLIB, we run into
a build failure:
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_probe':
drivers/net/ethernet/ti/cpsw.c:3006:9: error: implicit declaration of function 'devm_gpiod_get_array_optional' [-Werror=implicit-function-declaration]
mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/cpsw.c:3006:59: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);
Since we cannot rely on this to be visible from gpio.h, we have to include
gpio/consumer.h directly.
Fixes: 2652113ff0 ("net: ethernet: ti: Allow most drivers with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building on a 64-bit host we will get the following warning:
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_add_ch_strings':
drivers/net/ethernet/ti/cpsw.c:1284:19: warning: format '%d' expects
argument of type 'int', but argument 5 has type 'long unsigned int'
[-Wformat=]
"%s DMA chan %d: %s", rx_dir ? "Rx" : "Tx",
~^
%ld
Fix this by using an %ld format and casting to long.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The early versions of am33xx devices, related to ES1.0 SoC revision
have errata limiting mq support. That's the same errata as
commit 7da1160002 ("drivers: net: cpsw: add am335x errata workarround for
interrutps")
AM33xx Errata [1] Advisory 1.0.9
http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
After additional investigation were found that drivers w/a is
propagated on all AM33xx SoCs and on DM814x. But the errata exists
only for ES1.0 of AM33xx family, limiting mq support for revisions
after ES1.0. So, disable mq support only for related SoCs and use
separate polls for revisions allowing mq.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
- connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
- connect port 2 (eth1) to linux Host 1 with vlan 1 configured
- ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.
Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.
To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA_TX_PRIORITY_MAP in real is vlan pcp field priority mapping
register and basically replaces vlan pcp field for tagged packets.
So, set it to be 1:1 mapping. Otherwise, it will cause unexpected
change of egress vlan tagged packets, like prio 2 -> prio 5.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently <linux/slab.h> #includes <linux/kmemleak.h> for no obvious
reason. It looks like it's only a convenience, so remove kmemleak.h
from slab.h and add <linux/kmemleak.h> to any users of kmemleak_* that
don't already #include it. Also remove <linux/kmemleak.h> from source
files that do not use it.
This is tested on i386 allmodconfig and x86_64 allmodconfig. It would
be good to run it through the 0day bot for other $ARCHes. I have
neither the horsepower nor the storage space for the other $ARCHes.
Update: This patch has been extensively build-tested by both the 0day
bot & kisskb/ozlabs build farms. Both of them reported 2 build failures
for which patches are included here (in v2).
[ slab.h is the second most used header file after module.h; kernel.h is
right there with slab.h. There could be some minor error in the
counting due to some #includes having comments after them and I didn't
combine all of those. ]
[akpm@linux-foundation.org: security/keys/big_key.c needs vmalloc.h, per sfr]
Link: http://lkml.kernel.org/r/e4309f98-3749-93e1-4bb7-d9501a39d015@infradead.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au> [2 build failures]
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [2 build failures]
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to AM335x TRM[1] 14.3.6.2, AM437x TRM[2] 15.3.6.2 and
DRA7 TRM[3] 24.11.4.8.7.3.3, in-band mode in EXT_EN(bit18) register is only
available when PHY is configured in RGMII mode with 10Mbps speed. It will
cause some networking issues without RGMII mode, such as carrier sense
errors and low throughput. TI also mentioned this issue in their forum[4].
This patch adds the check mechanism for PHY interface with RGMII interface
type, the in-band mode can only be set in RGMII mode with 10Mbps speed.
References:
[1]: https://www.ti.com/lit/ug/spruh73p/spruh73p.pdf
[2]: http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf
[3]: http://www.ti.com/lit/ug/spruic2b/spruic2b.pdf
[4]: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/640765/2392155
Suggested-by: Holsety Chen (陳憲輝) <Holsety.Chen@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was discovered that simple program which indefinitely sends 200b UDP
packets and runs on TI AM574x SoC (SMP) under RT Kernel triggers network
watchdog timeout in TI CPSW driver (<6 hours run). The network watchdog
timeout is triggered due to race between cpsw_ndo_start_xmit() and
cpsw_tx_handler() [NAPI]
cpsw_ndo_start_xmit()
if (unlikely(!cpdma_check_free_tx_desc(txch))) {
txq = netdev_get_tx_queue(ndev, q_idx);
netif_tx_stop_queue(txq);
^^ as per [1] barier has to be used after set_bit() otherwise new value
might not be visible to other cpus
}
cpsw_tx_handler()
if (unlikely(netif_tx_queue_stopped(txq)))
netif_tx_wake_queue(txq);
and when it happens ndev TX queue became disabled forever while driver's HW
TX queue is empty.
Fix this, by adding smp_mb__after_atomic() after netif_tx_stop_queue()
calls and double check for free TX descriptors after stopping ndev TX queue
- if there are free TX descriptors wake up ndev TX queue.
[1] https://www.kernel.org/doc/html/latest/core-api/atomic_ops.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not correct to return NULL when that is actually an error and
function returns errors in any other wrong case. In the same time,
the cpsw driver and davinci emac doesn't check error case while
creating channel and it can miss actual error. Also remove WARNs
replacing them on dev_err msgs.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpsw_ale_create in cpsw_ale_create(). This also makes
cpsw_ale_destroy() function nop, so remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI OMAP/Sitara SoCs have fixed number of ALE ports 3, which includes Host
port also.
Hence, use fixed value instead of value calcualted from DT, which can be
set by user and might not reflect actual HW configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mac_hi/lo defines in common header cpsw.h and re-use
them for netcp_ethss.c.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW platform data struct cpsw_platform_data and struct cpsw_slave_data are
used only incide cpsw.c module, so move these definitions there.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use writel_relaxed/readl_relaxed() IO API instead of raw version
as it is recommended.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop unused variable "poll" from cpsw_update_channels_res().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPSW driver configures min eth packet size to 60 octets (ETH_ZLEN)
which works in most of cases, but when port VLAN is configured on some
switch port, it also can be configured to force all egress packets to be
VLAN untagged. And in this case, CPSW driver will pad small packets to 60
octets, but final packet size on port egress can became less than 60 octets
due to VLAN tag removal and packet will be dropped.
Hence, fix it by accounting VLAN header in CPSW min eth packet size. While
here, use proper defines for CPSW_MAX_PACKET_SIZE also, instead of open
coding.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.
Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpts can timestmap only ptp packets at this moment, so driver
cannot mark every packet as though it's going to be timestamped,
only because h/w timestamping for given skb is enabled with
SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result
outgoing packet is not timestamped at all if it's not PTP and h/w
timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS
only for PTP packets.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sw timestamp function close to channel submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver supports PTP v1 messages, but for unknown reasons this filter
is not advertised. As result,
./tools/testing/selftests/networking/timestamping/timestamping utility
can't be used for testing of CPSW RX timestamping with option
SOF_TIMESTAMPING_RX_HARDWARE, because it uses
HWTSTAMP_FILTER_PTP_V1_L4_SYNC filter.
Hence, fix it by advertising HWTSTAMP_FILTER_PTP_V1_L4_XXX filters
in CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When users set flow control using ethtool the bits are set properly in the
CPGMAC_SL MACCONTROL register, but the FIFO depth in the respective Port n
Maximum FIFO Blocks (Pn_MAX_BLKS) registers remains set to the minimum size
reset value. When receive flow control is enabled on a port, the port's
associated FIFO block allocation must be adjusted. The port RX allocation
must increase to accommodate the flow control runout. The TRM recommends
numbers of 5 or 6.
Hence, apply required Port FIFO configuration to
Pn_MAX_BLKS.Pn_TX_MAX_BLKS=0xF and Pn_MAX_BLKS.Pn_RX_MAX_BLKS=0x5 during
interface initialization.
Cc: Schuyler Patton <spatton@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI's cpsw driver handles both OF and non-OF case for phy
connect. Unfortunately of_phy_connect() returns NULL on
error while phy_connect() returns ERR_PTR().
To handle this, cpsw_slave_open() overrides the return value
from phy_connect() to make it NULL or error.
This leaves a small window, where cpsw_adjust_link() may be
invoked for a slave while slave->phy pointer is temporarily
set to -ENODEV (or some other error) before it is finally set
to NULL.
_cpsw_adjust_link() only handles the NULL case, and an oops
results when ERR_PTR() is seen by it.
Note that cpsw_adjust_link() checks PHY status for each
slave whenever it is invoked. It can so happen that even
though phy_connect() for a given slave returns error,
_cpsw_adjust_link() is still called for that slave because
the link status of another slave changed.
Fix this by using a temporary pointer to store return value
of {of_}phy_connect() and do a one-time write to slave->phy.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case, if TX watchdog is fired some or all netdev TX queues will be
stopped and as part of recovery it is required not only to drain and
reinitailize CPSW TX channeles, but also wake up stoppted TX queues what
doesn't happen now and netdevice will stop transmiting data until
reopenned.
Hence, add netif_tx_wake_all_queues() call in .ndo_tx_timeout() to complete
recovery and restore TX path.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale is a property of cpsw, so change dev to cpsw->dev,
aka pdev->dev, to be consistent.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage count function is based on ndev_running flag that is
updated before calling ndo_open/close, but if ndo is called in
another place, as with suspend/resume, the counter is not changed,
that breaks sus/resume. For common resource no difference which
device is using it, does matter only device count. So, replace
usage count function on var and inc and dec it in ndo_open/close.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_padto failed the skb has been dropped already, so it was
consumed, but it doesn't mean it was sent, thus no need to update
queue tx time, etc. So, return NET_XMIT_DROP as more appropriate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice, it's supposed to be
done in netdev_start_xmit() and anyway is re-written. Also, no reason to
update trans time in case of an error.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switch mode on struct cpsw_slave->ndev field will be initialized with
proper value only for the one cpsw slave port, as result
cpsw_get_usage_count() will generate "Unable to handle kernel NULL pointer
dereference" exception when first ethernet interface is opening
cpsw_ndo_open(). This issue causes boot regression on AM335x EVM and
reproducible on am57xx-evm (switch mode).
Fix it by adding additional check for !cpsw->slaves[i].ndev in
cpsw_get_usage_count().
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: 03fd01ad0e ("net: ethernet: ti: cpsw: don't duplicate ndev_running")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding cpsw_set_ringparam ethtool op, better to carry out
common parts of similar ops splitting descriptors in runtime. It
allows to reuse these parts and shows what the ops actually do.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate the same function in rx handler to get info
if any interface is running.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to create additional vars to identify if interface is running.
So simplify code by removing redundant var and checking usage counter
instead.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to disable interrupts if no open devices,
they are disabled anyway.
Even no need to disable interrupts if some ndev is opened, In this
case shared resources are not touched, only parameters of ndev shell,
so no reason to disable them also. Removed lines have proved it.
So, no need in redundant check and interrupt disable.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common res usage is possible only in case an interface is
running. In case of not dual emac here can be only one interface,
so while ndo_open and switch mode, only one interface can be opened,
thus if open is called no any interface is running ... and no common
res are used. So remove check on dual emac, it will simplify
code/understanding and will match the name it's called.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to set number of descs close to possible values. In case of
minimum limit it's equal to number of channels to be able to set
at least one desc per channel. For maximum limit leave enough descs
number for tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA uses one pool of descriptors for both RX and TX which by default
split between all channels proportionally depending on total number of
CPDMA channels and number of TX and RX channels. As result, more
descriptors will be consumed by TX path if there are more TX channels and
there is no way now to dedicate more descriptors for RX path.
So, add the ability to re-split CPDMA pool of descriptors between RX and TX
path via ethtool '-G' command wich will allow to configure and fix number
of descriptors used by RX and TX path, which, then, will be split between
RX/TX channels proportionally depending on RX/TX channels number and
weight. ethtool '-G' command will accept only number of RX entries and rest
of descriptors will be arranged for TX automatically.
Command:
ethtool -G <devname> rx <number of descriptors>
defaults and limitations:
- minimum number of rx descriptors is 10% of total number of descriptors in
CPDMA pool
- maximum number of rx descriptors is 90% of total number of descriptors in
CPDMA pool
- by default, descriptors will be split equally between RX/TX path
- any values passed in "tx" parameter will be ignored
Usage:
# ethtool -g eth0
Pre-set maximums:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 0
Current hardware settings:
RX: 4096
RX Mini: 0
RX Jumbo: 0
TX: 4096
# ethtool -G eth0 rx 7372
# ethtool -g eth0
Ring parameters for eth0:
Pre-set maximums:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 0
Current hardware settings:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 820
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW CPDMA can process buffer descriptors placed as in internal
CPPI RAM as in DDR. This patch adds support in CPSW and CPDMA for
descs_pool_size mudule parameter, which defines total number of CPDMA CPPI
descriptors to be used for both ingress/egress packets processing:
- memory size, required for CPDMA descriptor pool, is calculated basing
on number of descriptors specified by user in descs_pool_size and
CPDMA descriptor size and allocated from coherent memory (CMA area);
- CPDMA descriptor pool will be allocated in DDR if pool memory size >
internal CPPI RAM or use internal CPPI RAM otherwise;
- if descs_pool_size not specified in DT - the default value 256 will
be used which will allow to place CPDMA descriptors pool into the
internal CPPI RAM (current default behaviour);
- CPDMA will ignore descs_pool_size if descs_pool_size = 0 for
backward comaptiobility with davinci_emac.
descs_pool_size is boot time setting and can't be changed once
CPSW/CPDMA is initialized.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook