Commit Graph

101 Commits

Author SHA1 Message Date
Paul Walmsley 464b500e37 avr32: favr-32: clk_round_rate() can return a zero upon error
Treat both negative and zero return values from clk_round_rate() as
errors.  This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.

Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error.  All other values will be considered valid
rates.  The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Håvard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
2013-12-10 08:46:38 +01:00
Jean-Christophe PLAGNIOL-VILLARD ce3b64f5f1 video: atmel_lcdfb: pass the pdata as params
so we can use have list gpio as example (probe via DT)

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2013-09-27 09:26:20 +03:00
Jean-Christophe PLAGNIOL-VILLARD 8af2c2869f video: atmel_lcdfb: fix platform data struct
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2013-09-27 09:26:19 +03:00
Cong Ding c4afd7b95f avr32: boards/atngw100/mrmt.c: fix building error
there is an additional "{", which causes building error.

Signed-off-by: Cong Ding <dinggnu@gmail.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
2013-08-08 14:16:22 +02:00
Fengguang Wu 6c55845e71 avr32: fix build error in ATSTK1002 code
Fix the error

  arch/avr32/boards/atstk1000/atstk1002.c💯 error: 'num_partitions' undeclared here (not in a function)

which was introduced by commit 1754aab9bb ("mtd: ATMEL, AVR32: inline
nand partition table access ").

Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-07-30 17:25:13 -07:00
Jean-Christophe PLAGNIOL-VILLARD bf4289cba0 ATMEL: fix nand ecc support
So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).

Set ecc mode in the boards to soft as currently in the driver.

Move platform data to a common header
include/linux/platform_data/atmel_nand.h

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: David Woodhouse <dwmw2@infradead.org>
2012-03-15 23:26:32 +08:00
Linus Torvalds acc952c1f3 Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
 drivers, the bulk of these is for mach-91.
 
 I ended up pulling in the restart branch from Russell in order to
 fix up some simple but annoying merge conflicts.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIVAwUATwtcbmCrR//JCVInAQLONg/+PnaGQ9gt+dRQD1kzvOl1uE4veBD4KJ3j
 k3ew36OpcbkjKbcZjkN42tXbM5nBAC5A9w+iKy0RZvvxO+iay8A3IdYhlnpJhMCY
 LLvv8bUltR3iB5BPJO8MXgUAkHbec/8yGZ+Zu9LfQOC8LvaXW4ARiy7RLuA01MAM
 EUyL0cSAS5iztlJ1j9qwaQ+k6kReLSVkG1MRcTjPwHu75zWA2ADdQmkfb1jo6v9o
 3NF4QX2aw2tpPWn7B443irVLiZFG01gBugktl2z4VcNEHLHaU7eJUddh9146FVFd
 WZPz6y4qJHXJkAsL2QdEHwCet2yphf32XXAGJVVOSsr5EEqfAawPLQCt8qPaN6Un
 M+BLVlf3Wtv6JmGC+ECYvHEKdu04Zw1ia43cG7VOCgpoZjdo2HgaHIjL2t96Zj7N
 OpESMNiSp8++G7Gw+TxovDG93nBT459A12i3xhf/ljz2X1ADDSc6S0h+Vfi17201
 XcLH9ctJn17TfO8+KBwSYM3W3V1I6APHoKRN41q4u+fHnxu93jLnMeGDqRyscxRq
 BWvH1XmbkLBEb0HPtN30rTkVEnOMx4ZozM6/htVrdSRLKO+ss7XCRXLbWZxx3mWb
 sCvc1E5A1GmPmhOE8P+DqFVZlZXsIVHPsnp/nLjzCZFsIv0x2RdGjd7wXK605z0Z
 d+u3fNUEiHA=
 =9q+1
 -----END PGP SIGNATURE-----

Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Cleanups on various subarchitectures

Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.

Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
  arm/at91: fix build of stamp9g20
  ARM: u300: delete memory.h
  MAINTAINERS: add maintainer entry for Picochip picoxcell
  ARM: picoxcell: move io mappings to common.c
  ARM: picoxcell: don't reserve irq_descs
  ARM: picoxcell: remove mach/memory.h
  ARM: at91: delete the pcontrol_g20_defconfig
  arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
  arm/tegra: remove unused defines
  arm/tegra: fix variable formatting in makefile
  ARM: davinci: vpif: move code to driver core header from platform
  ARM: at91/gpio: fix display of number of irq setuped
  ARM: at91/gpio: drop PIN_BASE
  ARM: at91/udc: use gpio_is_valid to check the gpio
  ARM: at91/ohci: use gpio_is_valid to check the gpio
  ARM: at91/nand: use gpio_is_valid to check the gpio
  ARM: at91/mmc: use gpio_is_valid to check the gpio
  ARM: at91/ide: use gpio_is_valid to check the gpio
  ARM: at91/pata: use gpio_is_valid to check the gpio
  ARM: at91/soc: use gpio_is_valid to check the gpio
  ...
2012-01-09 14:21:03 -08:00
Kay Sievers edbaa603eb driver-core: remove sysdev.h usage.
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.

The sysdev code will be going away soon, so this include needs to be
removed no matter what.

Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
2011-12-21 16:26:03 -08:00
Jamie Iles 84e0cdb0a2 macb: unify at91 and avr32 platform data
Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin.  Create a common
macb_platform_data for macb that both at91 and avr32 can use.  In
future we can use this to support other architectures that use the
same IP block with the macb driver.

v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2011-11-22 15:21:16 +00:00
Dmitry Eremin-Solenikov 1754aab9bb mtd: ATMEL, AVR32: inline nand partition table access
Currently atmel_nand driver used by AT91 and AVR32 calls a special callback
which return nand partition table and number of partitions. However in all
boards this callback returns just static data. So drop this callback and
make atmel_nand use partition table provided statically via platform_data.

Nicolas Ferre: I am in favor for a mainline inclusion through linux-mtd tree.
Hans-Christian Egtvedt: I'm fine by sending the changes for AVR32 through linux-mtd

Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2011-09-11 15:01:57 +03:00
Thomas Gleixner d75f1bfdbc avr: Cleanup genirq namespace
Scripted conversion to new function names with coccinelle.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-03-24 20:35:55 +01:00
Vasiliy Kulikov 36b471e047 avr32: boards: setup: use IS_ERR() instead of NULL check
clk_get() returns ERR_PTR() on error, not NULL.

Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2011-01-13 20:40:53 +01:00
Arnd Bergmann 6038f373a3 llseek: automatically add .llseek fop
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.

The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.

New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time.  Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.

The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.

Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.

Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.

===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
//   but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}

@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}

@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
   *off = E
|
   *off += E
|
   func(..., off, ...)
|
   E = *off
)
...+>
}

@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}

@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
  *off = E
|
  *off += E
|
  func(..., off, ...)
|
  E = *off
)
...+>
}

@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}

@ fops0 @
identifier fops;
@@
struct file_operations fops = {
 ...
};

@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
 .llseek = llseek_f,
...
};

@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
 .read = read_f,
...
};

@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
 .write = write_f,
...
};

@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
 .open = open_f,
...
};

// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
...  .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};

@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
...  .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};

// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
...  .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};

// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};

// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};

@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+	.llseek = default_llseek, /* write accesses f_pos */
};

// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////

@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
 .write = write_f,
 .read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};

@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};

@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};

@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
2010-10-15 15:53:27 +02:00
Linus Torvalds 050cbb09da Merge git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: update default configurations for ATNGW100, ATSTK1002 and ATSTK1006
  avr32: add default configurations for ATNGW100 mkII and EVKLCD10X
  avr32: add support for ATNGW100 mkII board
  avr32: convert to asm-generic/hardirq.h
  avr32: add two new at91 to cpu.h definition
  avr32: clean up linker script using standard macros.
  avr32: MRMT: correct setup of SPI slaves
  avr32: function for independently setting up SPI slaves
  avr32: re-instate MCI WP/CD pin assignments for ATNGW100
2009-12-15 09:01:00 -08:00
Hans-Christian Egtvedt 3550b9313b avr32: add support for ATNGW100 mkII board
This patch adds board support for ATNGW100 mkII. This board is an upgrade of
the ATNGW100 where the difference is an additional 256 MB NAND flash device and
128 MB 32-bit SDRAM instead of the 32 MB 16-bit SDRAM on ATNGW100.

Tested on ATNGW100 mkII, duh (-:

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-12-14 19:33:33 +01:00
André Goddard Rosa af901ca181 tree-wide: fix assorted typos all over the place
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:55 +01:00
Peter Ma d55651168a avr32: MRMT: correct setup of SPI slaves
For MRMT1/2 add-on card to Atmel ATNGW100.

This patch implements the SPI slave setup method created by patch:
<<avr32: function for independently setting up SPI slaves>>

Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-08-27 10:20:58 +02:00
Peter Ma 3fe6ad6c39 avr32: re-instate MCI WP/CD pin assignments for ATNGW100
The MRMT1 patch mistakenly reverted commit
fe272b5bd1.

This new patch is intended to correct this, so that both daughtercards
should be able to assign GPIO PC25 and PE0 to the MCI driver.

Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-08-27 10:20:57 +02:00
Ben Nizette 92c548cd35 favr32: improve touchscreen response
The ezLCD+101 board (to which an favr-32 is fitted) has a long,
unshielded, nasty lead between the touch panel and the ads7843 touch
controller.  In order to get satisfactory response then, we need to
employ every noise-reduction trick in the driver's arsenal.  After
extensive fiddling I've found some good settings:

1) We keep vref on all the time to dramatically reduce settling times
(at the cost of a tiny increase in power consumption).

2) Despite 1 the settling time is still non-zero.  500uS is plenty of
time for the signals to settle

3) Despite 1 and 2 there's still a little bit of noise around.  By
setting a pen recheck delay we make the panel feel less touchy and
twitchy.

Someone with more time and patience myself might be able to tune this
numbers further but these settings are now perfectly acceptable for
normal use.

Tested on ezLCD+101 though should only improve response on other ezLCD+/
favr-32 boards too.

Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-07-27 13:16:45 +02:00
Haavard Skinnemoen fbe0b8d582 Merge branch 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6 2009-06-13 15:34:22 +02:00
Peter Ma 4024533e60 avr32: Add support for Mediama RMTx add-on board for ATNGW100
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-06-08 12:55:35 +02:00
Peter Ma a89ab11454 avr32: Change Atmel ATNGW100 config to add choice of add-on board
Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-06-08 12:54:02 +02:00
Mark Jackson c878b7d604 Fix MIMC200 board LCD init
This patch updates the LCD init code for the MIMC200 board.

V2 fixes a .yres typo and corrects an incorrect setup value
in the call to at32_add_device_lcdc()

Without this patch, the lcd setup is wrong and won't display images
correctly (if at all !!)

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-06-03 15:10:04 +02:00
Jonas Larsson 7ebcfcf197 avr32: Solves problem with inverted MCI detect pin on Merisc board
Same patch as before, modified to use bool.

This patch solves the problem with the inverted mci detect pin on Merisc
boards.

Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-04-08 20:48:02 +02:00
Yang Hongyang 284901a90a dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07 08:31:11 -07:00
Peter Ma bf4861cf3e avr32: add RTS/CTS/CLK pin selection for the USARTs
Adds extra parameter to AT32 at32_map_usart(), so as to reserve
RTS/CTS/CLK pins.

All boards under arch/avr32/boards have been updated (trivial change), but
not all have been tested.

Signed-off-by: Peter Ma <pma@mediamatech.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-04-01 16:13:45 +02:00
Jonas Larsson a6b6b5ff8f Add RTC support for Merisc boards
This patch adds RTC support for the Merisc boards.

Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-30 17:17:58 +02:00
Hans-Christian Egtvedt 2f47c8c555 avr32: at32ap700x: setup DMA for AC97C in the machine code
This patch will adjust the setup the DMA controller for the AC97
Controller in the at32ap700x machine code. This setup matches the new
ALSA driver for the AC97C.

The struct ac97c_platform_data has been moved into its own header file
located in the sound include path.

Tested on ATSTK1006 + ATSTK1000.

This patch will setup the AC97 controller properly for the adjusted
machine code. Both EVKLCD10x and Hammerhead board has been updated.

Tested on EVKLCD10x, and copied to Hammerhead board.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold with board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-27 16:15:39 +01:00
Hans-Christian Egtvedt 6b0c935142 avr32: at32ap700x: setup DMA for ABDAC in the machine code
This patch will adjust the setup the DMA controller for the Audio
Bistream DAC in the at32ap700x machine code. This setup matches the new
ALSA driver for the ABDAC.

Tested on ATSTK1006 + ATSTK1000.

This patch will setup the needed platform data for the Audio Bistream
DAC used by the Favr-32 board.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: fold board code update]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-27 16:15:39 +01:00
Jonas Larsson a16fffdd8e Add Merisc board support
Merisc is the family name for a range of AVR32-based boards.

The boards are designed to be used in a man-machine interfacing
environment, utilizing a touch-based graphical user interface. They host
a vast range of I/O peripherals as well as a large SDRAM & Flash memory
bank.

For more information see: http://www.martinsson.se/merisc

Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-27 15:02:34 +01:00
Hans-Christian Egtvedt b2a49ed008 avr32: fix timing LCD parameters for EVKLCD10X boards
This patch adjusts the timing parameters for the Kyocera LCD panels
connected on the EVKLCD10X addon boards.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-26 14:58:58 +01:00
Hans-Christian Egtvedt 30754acf29 avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
The PB15 GPIO line is used to control the enable and disable signal for
the backlight regulator on EVKLCD10x boards. This patch hands the I/O
line over to the LCDC driver, which will control when to enable and
disable the backlight.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
[haavard.skinnemoen@atmel.com: reverted ac97c change]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-26 14:58:28 +01:00
Hans-Christian Egtvedt fe272b5bd1 avr32: configure MCI detect and write protect pins for EVKLCD10x boards
This patch removes the special handling of MCI platform data for
EVKLCD10x boards. This is now possible since the pin mask for the LCD
controller is no longer reserving the I/O lines used for MCI card
detection and write protect.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-26 14:49:40 +01:00
Hans-Christian Egtvedt ecb1bd894e avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
This patch will set the pin mask to alternative 18 bits per pixel output
for EVKLCD10x boards.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-26 14:49:39 +01:00
Huang Weiyi 5201b0a47b avr32: remove duplicated #include
Remove duplicated #include in arch/avr32/boards/hammerhead/flash.c.

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Acked-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-03-24 09:16:51 +01:00
Haavard Skinnemoen 4209324a74 avr32: data param to at32_add_device_mci() must be non-NULL
at32_add_device_mci() will refuse to add the mci device if the data
parameter is NULL. Fix up the favr-32 and hammerhead boards so that this
doesn't happen.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alex Raimondi <mailinglist@miromico.ch>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
2009-01-05 17:14:22 +01:00
Haavard Skinnemoen 0e49005090 Merge branch 'move-atmel-mci-h' into boards 2009-01-05 16:36:07 +01:00
Nicolas Ferre c42aa775cc atmel-mci: move atmel-mci.h file to include/linux
Needed to use the atmel-mci driver in an architecture
independant maner.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-05 16:35:31 +01:00
Alex Raimondi dd5e1339e5 avr32: Hammerhead board support
The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel.  It offers versatile peripherals, such as ethernet, usb
device, usb host etc.

The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).

Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.

This patch does include the basic support for the fpga device driver,
but not the device driver itself.

Signed-off-by: Alex Raimondi <mailinglist@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-05 15:52:04 +01:00
Haavard Skinnemoen bc08969fe6 Merge branch 'cleanups' into boards 2009-01-05 15:51:52 +01:00
Alex Raimondi adde42b583 avr32: Allow reserving multiple pins at once
at32_reserve_pin now takes an u32 bitmask rather than a single pin.
This allows to reserve multiple pins at once.

Remove (undocumented) SDCS (pin PE26) from reservation in board
setup code.

Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-05 12:16:13 +01:00
Haavard Skinnemoen 45f926912f favr-32: Remove deprecated call
at32_add_system_devices() is deprecated, so remove the call to it.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-05 12:15:14 +01:00
Mark Jackson 8d3d3fb922 MIMC200: Remove deprecated call
This patch removes a call to the deprecated function
at32_add_system_devices().

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-05 11:35:16 +01:00
Haavard Skinnemoen 8983fdb508 avr32: favr-32 build fix
The favr-32 board code still refers to the old asm/arch header files
which were moved to mach/ some time ago.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-12-18 16:22:13 +01:00
Haavard Skinnemoen d9214556b1 Merge branches 'boards' and 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6 2008-10-23 15:24:10 +02:00
Haavard Skinnemoen e82c6106b0 avr32: Fix GPIO initcall breakage
Add essential system devices, including GPIO controllers, automatically
at core_initcall time. This ensures that the devices are there when the
PIO driver gets initialized at postcore_initcall, fixing a bug exposed
by commit d6634db8fe "avr32: Use
platform_driver_probe for pio platform driver".

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-23 15:18:33 +02:00
Mark Jackson 5b50c166b7 avr32: Add MIMC200 board support
Please consider the following patch which adds support for a new AVR32
based board.

The board is closely based on Atmel's NGW100 reference board, but has an
extra 8MByte FLASH and 128KByte FRAM.

Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-13 16:36:25 +02:00
Hans-Christian Egtvedt 45c349b58c avr32: add support for EarthLCD Favr-32 board
This patch adds support for the Favr-32 board made by EarthLCD.

This kit, which is also called ezLCD-101, has a 10.4" touch screen LCD panel,
16 MB 32-bit SDRAM, 8 MB parallel flash, Ethernet, audio out, USB device,
SD-card slot, USART and various other connectors for cennecting stuff to SPI,
I2C, GPIO, etc.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-13 16:01:18 +02:00
Hans-Christian Egtvedt a3bee42f05 avr32: Add support for EVKLCD10X addon boards
This patch lets the user enable support for EVKLCD100 and EVKLCD101
(refered to by EVKLCD10X). By enabling EVKLCD10X support the LCD
controller and AC97 controller platform devices are added.

The user can also choose between the EVKLCD100 (QVGA display) and the
EVKLCD101 (VGA display), this is added to automagically select the
correct panel timing and resolution parameters.

Enabling support for EVKLCD10X addon board will cripple the MCI platform
device a bit since they share two GPIO lines (detect and write-protect).
These two lines are disabled when EVKLCD10X is enabled.

The default configurations are based upon ATNGW100, but with added AC97C
and LCDC driver. Virtual terminal is also enabled by default for
EVKLCD10X boards.

Verified on hardware with a NGW100 + EVKLCD100/101.

Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-13 12:56:24 +02:00
Haavard Skinnemoen 6eb3ebe04d avr32: Fix build failures in board code
Fix a few instances of board code breakage introduced by the atmel-mci
platform interface changes.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-10-12 16:13:28 +02:00