To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the 8250 as a boot console and the main console results in
messages being printed twice. The console framework will only
unregister boot consoles if a new console is registered with the
CON_CONSDEV flag set.
Set this flag for the univ8250 console to prevent double-registration.
Signed-off-by: Matthew Leach <matthew.leach@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver makes use of the __set_bit() and __clear_bit() functions.
When running under big-endian, these functions don't convert the bit
indexes when working with peripheral registers, leading to the
incorrect bits being set and cleared when running big-endian.
Add two new driver functions for setting and clearing bits that are
byte-order aware.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the serial access code to deal with kernels built for big endian
operation.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo mask functions should be static as they are not
used outside of the driver. Fix the following warnings by
making them static:
drivers/tty/serial/sirfsoc_uart.h:109:5: warning: symbol 'uart_usp_ff_full_mask' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.h:117:5: warning: symbol 'uart_usp_ff_empty_mask' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of mps2-uart is:
config SERIAL_MPS2_UART
bool "MPS2 UART port"
depends on ARM || COMPILE_TEST
...meaning that it currently is not being built as a module by anyone.
Follow commit 89ebc27427 ("drivers/tty: make serial/mvebu-uart.c
explicitly non-modular") as an example of moving modular code to
non-modular:
- remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
- explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
- use arch_initcall instead of module_init and remove module_exit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.
With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: <stable@vger.kernel.org>
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm63xx_uart driver uses the of alias for determing its id. Recent
changes in dts files changed the expected 'uartX' to the recommended
'serialX', breaking serial output. Fix this by checking for a 'serialX'
alias as well.
Fixes: e3b992d028 ("MIPS: BMIPS: Improve BCM6328 device tree")
Fixes: 2d52ee82b4 ("MIPS: BMIPS: Improve BCM6368 device tree")
Fixes: 7537d273e2 ("MIPS: BMIPS: Add device tree example for BCM6358")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_M32R_SIO
drivers/tty/serial/Kconfig: bool "M32R SIO I/F"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_VT8500
drivers/tty/serial/Kconfig: bool "VIA VT8500 on-chip serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_PXA
drivers/tty/serial/Kconfig: bool "PXA serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE and MODULE_ALIAS are both a
no-op for non-modular builds.
We also delete the MODULE_LICENSE tag since that information is
already contained at the top of the file in the comments.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes assignment of port line automatically,
so now user allow to use several MAX310X chips.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves UART registration at module_init initcall,
so this should helps to add multiple chip support in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use resource managed functions devm_gpiochip_add_data() to make
error & exit path a bit simpler.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485 IOCTLs uses spinlocks, so move regmap functions into a separate
work queue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds support for the WCH CH355 4S card in the 8250 serial driver.
Signed-off-by: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On non-DeviceTree platforms, the index of serial device is a static
variable incremented on each probe. It is incremented even if deferred
probe happens when getting the clock in s3c24xx_serial_init_port().
This index is used for referencing elements of statically allocated
s3c24xx_serial_ports array. In case of re-probe, the index will point
outside of this array leading to memory corruption.
Increment the index only on successful probe.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: b497549a03 ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values. This leads to
dereferencing of ERR_PTR stored under ourport->clk:
12c30000.serial: Controller clock not found
(...)
12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
Unable to handle kernel paging request at virtual address fffffdfb
(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR). On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.
Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.
Fixes: 60e9357547 ("serial: samsung: enable clock before clearing pending interrupts during init")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).
The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.
This patch will check the current IRQ mode and apply correct mode to UART.
The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html
LDN0~3
70h: IRQ channel & Mode register
Bit 6~5 :
00 : Active low level mode
01 : Active high edge mode
Bit 4 : Sharing Flag (0: not share/1: share)
Bit 3~0 : IRQ channel
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocated memory for 'sport->irq_fault_name' is freed twice, first
in error check of 'if(!sport->irq_rx_name)' and other in fallback
handler.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the clocks are enabled at probe and disabled
at remove. Instead enable the clocks when used.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using DMA, half duplex doesn't work properly because rx is not stopped
before starting tx. Ensure we call atmel_stop_rx() in the DMA case.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a macro named ATMEL_SERIAL_RINGSIZE which suggesting that it
corresponds to the real size of the ring buffer. Let warn people that
there is a factor of four since allocation size is
sizeof(struct atmel_uart_char) * ATMEL_SERIAL_RINGSIZE.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split TX and RX paths to not schedule RX tasklet on TX events and vice versa.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ status check and related actions was done in the tasklet without
benefit. So, move it back to the IRQ context to simplify IRQ handling and
having the possibility to split the tasklet in two separated ones for
receive and transmit actions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are getting somewhat random soft lockups with this signature:
[ 86.992215] [<fffffc00080935e0>] el1_irq+0xa0/0x10c
[ 86.997082] [<fffffc000841822c>] cursor_timer_handler+0x30/0x54
[ 87.002991] [<fffffc000810ec44>] call_timer_fn+0x54/0x1a8
[ 87.008378] [<fffffc000810ef88>] run_timer_softirq+0x1c4/0x2bc
[ 87.014200] [<fffffc000809077c>] __do_softirq+0x114/0x344
[ 87.019590] [<fffffc00080af45c>] irq_exit+0x74/0x98
[ 87.024458] [<fffffc00080fac20>] __handle_domain_irq+0x98/0xfc
[ 87.030278] [<fffffc000809056c>] gic_handle_irq+0x94/0x190
This is caused by the vt visual_init() function calling into
fbcon_init() with a vc_cur_blink_ms value of zero. This is a
transient condition, as it is later set to a non-zero value. But, if
the timer happens to expire while the blink rate is zero, it goes into
an endless loop, and we get soft lockup.
The fix is to initialize vc_cur_blink_ms before calling the con_init()
function.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use memdup_user to duplicate a memory region from user-space to
kernel-space, instead of open coding using kmalloc & copy_from_user.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling support for the UART on the ARM MPS2 platform only make sense
when compiling for the ARM MPS2 platform, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msm_stop_dma() is not exported from the driver, so make
it static to stop the following warning:
drivers/tty/serial/msm_serial.c:84:6: warning: symbol 'msm_stop_dma' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For dm uarts in pio mode tx data is transferred to the fifo register 4
bytes at a time, but care is not taken when these 4 bytes spans the end
of the xmit buffer so the loop might read up to 3 bytes past the buffer
and then skip the actual data at the beginning of the buffer.
Fix this by, analogous to the DMA case, make sure the chunk doesn't
wrap the xmit buffer.
Fixes: 3a878c430f ("tty: serial: msm: Add TX DMA support")
Cc: Ivan Ivanov <iivanov.xz@gmail.com>
Cc: stable@vger.kernel.org
Reported-by: Frank Rowand <frowand.list@gmail.com>
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Frank Rowand <frank.rowand@am.sony.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid data corruption issues that result in CRC errors during file
transfers over serial ports at higher baud rates.
The current msm_serial driver masks the FIFO Rx interrupts in
msm_start_rx_dma() since Rx FIFO interrupts are not required in DMA
mode. However, msm_complete_rx_dma() re-enables the Rx FIFO interrupts
which could cause RXSTALE event to be processed when a TXLEV interrupt
occurs.
The following is the sequence of events that could occur resulting in
data corruption.
msm_start_rx_dma -> msm_complete_rx_dma -->
spin_unlock_irqrestore(&port->lock) -->
msm_uart_irq()(For TXLEV interrupt) --> msm_handle_rx_dm() (Read from
FIFO resulting in data corruption)
The patch fixes the issue by not restoring the RXLEV and RXSTALE
interrupts in msm_complete_rx_dma(). These interrupts are required only
in FIFO mode.
Signed-off-by: Charanya Venkatraman <charanya@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hrtimer include isn't used and neither is serial. Drop those
ones. The irq.h header really should be interrupt.h because this
is an interrupt user and not an interrupt chip. Finally add
wait.h for the wake_up*() usage in this driver and kernel.h for
container_of().
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The registers that msm_serial_set_mnd_regs() writes only exist on
the non-uartdm hardware, so let's return early here if this
function is called on uartdm hardware. This also prevents us from
messing up the uartclk variable if the uartclk rate happens to be
19.2 or 4.8 MHz.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This header file is only used by the driver, so let's merge the
two together to reduce files and make it easier to see the whole
driver without flipping through two files. This also makes it
easier to use the structures defined in msm_serial.c in the
functions that are defined in msm_serial.h by placing them in the
proper locations.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some board like Hisilicon D02 uses Synopsys DesignWare ABP UART, declare an
OF early console for it, so early console device can be enabled with comand
line "earlycon"(without option) via the "stdout-path" property in device-tree.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing timeout bit definition for (H)SCIF.
Clear the timeout and overrun flag bits during UART reset, cfr. the
initialization flowchart in the datasheet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting the FIFO reset bits is not sufficient to reset the RX FIFO.
After this the status register's RDF flag bit may still be set, causing
the reception of one stale byte of data.
To fix this, clear all status flag bits related to reception, error, and
break handling, cfr. the initialization flowchart in the datasheet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FIFO reset is done in sci_reset(), called from sci_set_termios(), while
sci_start_tx() and sci_start_rx() are called before, from sci_startup().
However, starting transfers before the UART's FIFOs have been reset may
cause reading of stale data.
Remove the calls to sci_start_tx() and sci_start_rx() from sci_startup()
to fix this.
Transfers are still started when needed:
- sci_start_rx() is called from sci_set_termios() after FIFO reset, if
the CREAD flag is set,
- sci_start_tx() is called from uart_change_speed() immediately
thereafter, if transmission is enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for indicating the availability of dedicated lines for
RTS/CTS hardware flow control, using the standard "uart-has-rtscts" DT
property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing support for hardware-assisted RTS/CTS is rudimentary and
doesn't work.
Add support for hardware-assisted RTS/CTS hardware flow control for the
(H)SCIF, SCIFA, and SCIFB variants.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before, the driver relied on initialization by the boot loader, or by
implicit reset state.
Note that unlike on (H)SCIF, the RTS/CTS bits exist only if dedicated
RTS/CTS pins are available, which depends on the SoC and UART instance.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct pin initialization on (H)SCIF:
- RTS must be deasserted (it's active low),
- SCK must be an input, as it may be used as the optional external
clock input.
Initial pin configuration must always be done:
- Regardless of the presence of dedicated RTS and CTS pins: if the
register exists, the RTS/CTS bits exist, too,
- Regardless of hardware flow control being enabled or not: RTS must
be deasserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve documentation for the SCIFA/SCIFB Serial Port Control and Data
Registers:
- State clearly that the RTS and CTS lines are active-low,
- Document the bits related to the serial port's SCK, RXD, and TXD
pins.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve documentation for the (H)SCIF Serial Port Register:
- Make it clear the RTS and CTS lines are active-low,
- Document the bits related to the serial port's clock pin.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded variants of sci_getreg() by function calls, and drop
intermediate variables where appropriate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enhance the Renesas SCI UART driver to add support for GPIO-controlled
modem lines (CTS, DSR, DCD, RNG, RTS, DTR), using the serial_mctrl_gpio
helpers.
GPIO-controlled modem lines can be used when dedicated modem lines are
not available. Invalid configurations specifying both GPIO RTS/CTS and
dedicated RTS/CTS are rejected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documentation/serial/driver clearly states:
If the port does not support CTS, DCD or DSR, the driver should
indicate that the signal is permanently active.
Hence always set TIOCM_CTS, as we currently don't look at the CTS
hardware line state at all.
FWIW, this fixes the transmit path when hardware-assisted flow control
is enabled, and userspace enables CRTSCTS.
The receive path is still broken, as RTS is never asserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vc_deccolm is only set and never read, remove the member from vc_data.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not do hashtables for unicode fonts since 1995 (1.3.28). So it
is time to remove the second parameter of con_clear_unimap and ignore
the advice from userspace completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Namely convert:
* IS_FG -> con_is_fg
* DO_UPDATE -> con_should_update
* CON_IS_VISIBLE -> con_is_visible
DO_UPDATE was a weird name for a yes/no answer, so the new name is
con_should_update.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flush the switch cases to be aligned with the switch. Mostly
everything can now fit to the 80-chars terminal.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not opencode max3, use the macro.
Separate commands. Until now, I have not noticed the comma. Make it
one line, one command. And make the code obvious.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compiler noticed passing structure over stack. Even though rgb is
a small structure, let us define one and pass that over all the
functions wherever needed.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code with T.416 high colors handling is flushed to the right and
hard to read. Move the code to a separate function and remove code
duplication for foreground & background colors.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a macro accessing and changing some local variables. And the code
uses it without appending semicolon which confuses everybody too.
Switch from this bad guy to a sane standard function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is never defined. And I spent quite some time looking into the
history and cannot find how this was ever used. Given it was not used
in the history, I doubt it currently works as expected after the years
of changes all over the code.
So kill it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is always called with 0, so remove the parameter and pass the
default down to scrolldelta without checking.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compiler complains about variables that are set, but never used:
* intX variables in exar_handle_irq
drivers/tty/serial/8250/8250_port.c:1864:34: warning: variable ‘int3’ set but not used [-Wunused-but-set-variable]
* val variable in pci_quatech_wqopr
drivers/tty/serial/8250/8250_pci.c:1139:10: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
And about a shadow variable:
* tmout in wait_for_xmitr is defined twice with the same type. Both of
them are also initialized before use.
Remove all of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq can fail, so we should handle negative value when
returned.
[v2]
platform_get_irq can actually return zero on some platforms. So do not
remove checks for irq == 0 there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert DEBUG_INTR to pr_debug:
* defined semantics (DEBUG, DYNAMIC_DEBUG)
* KERN_DEBUG level instead of KERN_DEFAULT
* emit __func__ and \n
* verified 'fmt' even when !DEBUG
I wonder if anybody ever used that or whether we should just drop the
lines.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hub6 and irqflags from struct old_serial_port are nowhere set. Drop
them from the structure and replace the reads by zeros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STD_COM_FLAGS is mostly a bad name for what the drivers thinks it is.
Stop using it and pass the flags directly.
cyclades defines it as 0, so we do not assign anything to freshly
tty_port_init'ed structure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not initialize members of initialized structures to zero. They are
zeroed automatically.
Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ipwireless_get_serial_info, struct serial_struct is memset to 0 and
then some members set to 0 explicitly.
Remove the latter as it is obviously superfluous.
And remove the retinfo check against NULL. copy_to_user will take care
of that.
Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Kosina <jikos@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The /dev/ptmx device node is changed to lookup the directory entry "pts"
in the same directory as the /dev/ptmx device node was opened in. If
there is a "pts" entry and that entry is a devpts filesystem /dev/ptmx
uses that filesystem. Otherwise the open of /dev/ptmx fails.
The DEVPTS_MULTIPLE_INSTANCES configuration option is removed, so that
userspace can now safely depend on each mount of devpts creating a new
instance of the filesystem.
Each mount of devpts is now a separate and equal filesystem.
Reserved ttys are now available to all instances of devpts where the
mounter is in the initial mount namespace.
A new vfs helper path_pts is introduced that finds a directory entry
named "pts" in the directory of the passed in path, and changes the
passed in path to point to it. The helper path_pts uses a function
path_parent_directory that was factored out of follow_dotdot.
In the implementation of devpts:
- devpts_mnt is killed as it is no longer meaningful if all mounts of
devpts are equal.
- pts_sb_from_inode is replaced by just inode->i_sb as all cached
inodes in the tty layer are now from the devpts filesystem.
- devpts_add_ref is rolled into the new function devpts_ptmx. And the
unnecessary inode hold is removed.
- devpts_del_ref is renamed devpts_release and reduced to just a
deacrivate_super.
- The newinstance mount option continues to be accepted but is now
ignored.
In devpts_fs.h definitions for when !CONFIG_UNIX98_PTYS are removed as
they are never used.
Documentation/filesystems/devices.txt is updated to describe the current
situation.
This has been verified to work properly on openwrt-15.05, centos5,
centos6, centos7, debian-6.0.2, debian-7.9, debian-8.2, ubuntu-14.04.3,
ubuntu-15.10, fedora23, magia-5, mint-17.3, opensuse-42.1,
slackware-14.1, gentoo-20151225 (13.0?), archlinux-2015-12-01. With the
caveat that on centos6 and on slackware-14.1 that there wind up being
two instances of the devpts filesystem mounted on /dev/pts, the lower
copy does not end up getting used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
commit 4047b37122 ("serial: core: Prevent unsafe uart port access,
part 1") added lockdep assertion for port mutex but fails to check
if debug_locks has disabled lockdep (so lock state is no longer
reliable).
Use lockdep_assert_held() instead, which properly checks lockdep
state as well.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdcea058e5 ("serial: 8250_dw: Avoid serial_outx code duplicate
with new dw8250_check_lcr()") introduce a wrong logic when write val to
LCR reg. When CONFIG_64BIT enabled, __raw_writeq is used unconditionally.
The __raw_readq/__raw_writeq is introduced by commit bca2092d78 ("serial:
8250_dw: Use 64-bit access for OCTEON.") for OCTEON.
So for 64BIT && !PORT_OCTEON, we better to use coincident write function.
Fixes: cdcea058e510("serial: 8250_dw: Avoid serial_outx code duplicate with new dw8250_check_lcr()")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the console is already registered, stop crawling the
registered_con_driver array and return an error immediatelly.
This makes the code more obvious. And we do not need to initialize
retval anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OUT1 and OUT2 pins present on some legacy UARTs are basically GPIOs.
It doesn't make much sense to emulate GPIOs using other GPIOs, hence
drop support for that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device HID AMDI0020 to match the AMD ACPI Vendor ID (AMDI) as
registered in http://www.uefi.org/acpi_id_list, and the UART
controller on future AMD paltform will use the HID instead of AMD0020.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.
This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:
1) f8747d4a46
tty: Fix pty master read() after slave closes
2) 52bce7f8d4
pty, n_tty: Simplify input processing on final close
3) 1a48632ffe
pty: Fix input race when closing
Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net>
Reported-by: Volth <openssh@volth.com>
Reported-by: Marc Aurele La France <tsi@tuyoix.net>
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_handle_cts_change should be called with port->lock held. And for
this to be save you must also disable irqs.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).
This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.
This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support early console for MPS2 UART which can be enabled via
earlycon=mps2,0x40004000
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver adds support to the UART controller found on ARM MPS2
platform.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the SiRF UART driver from using the vendor-specific
"sirf,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Freescale MXS AUART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but it is deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Freescale IMX UART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is not used outside the file, so it can be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA completed normally does not require termination; only terminate
paused rx dma stemming from rx dma flush.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.
Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the operation (restarting new rx dma) performed when error
argument is true.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c310c5c3 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaegine driver support terminate.
Query slave caps to determine if necessary commands/properties are
supported; disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaengine driver support error-free
pause/terminate and better-than-descriptor residue granularity. Query
slave caps to determine if necessary commands/properties are supported;
disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local mcr variable is never used in the tegra_uart_set_mctrl()
function, so it should be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->get_char() returns a negative error code and that can mean that
"ch" is uninitialized. The callers of this function expect NO_POLL_CHAR
on error so let's return that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We reach this point of code after a test of 'info->port.tty->hw_stopped',
we do not need to test for 'info->port.tty' as it is obvious that
info->port.tty is not NULL now, we have already dereferenced it.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function alloc_ctrl_packet() can fail and return NULL. Incase it
fails print an error message and exit.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HIGH_BITS_OFFSET is only used in the serial core; remove from 8250-
specific header.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If !up->dma == F, then up->dma == T and can be elided from the
(up->dma && up->dma->tx_err) sub-expression.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_err is not used other than for boolean evaluation;
substitute the actual operation directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Penwell and Tangier the HSU block (3 HSU ports) has a global register
set which is currently not used by the driver. On Tangier it has it's own PCI
device and thus available for enumeration. Since it's not a real HSU port we
just skip it and therefore put a comment in the code why we do so.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to compile module on non-X86 platforms, though COMPILE_TEST
is provided for sake of what it does.
While here, set default to SERIAL_8250 that user doesn't need an explicit
option to be set and hide it from non-expert.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BIT() macro, that is definded in bitops.h, is used in the driver. Include
necessary header for that.
While here, reorder included headers alphabetically.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bay Trail UART port does not support DCD and DSR lines. The driver
shall report that these signals are permanently active. This patch
is for HSUART enumerated via PCI.
For ACPI, see commit dfd37668ea ("serial: 8250_dw: Fix get_mctrl
behaviour"). The commit also describes the possible issue if these
signals are enabled on a port without these pins.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exposes get_mctrl() function so that it can be overriden with platform
specific implementation.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ifx_spi_complete, 'more' is not initialized. It is set only if the
status is clear and only if the header is parsed OK. If any of those
is not true, 'more' can be used uninitialized in that function later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every user of default_red, default_grn, and default_blu treats them as
unsigned char. So make it really unsigned char.
And indent the initializers and module_param properly.
This saves ~ 100 bytes of data.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means all ->con_set_palette have to have the second parameter
const too now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some code in vc_allocate is indented by 4 spaces. It is inside a
condition. Invert the condition and move the code to the first
indentation level (using \tab). And insert some empty lines to have
logical code blocks separated.
Then, instead of freeing in an 'if' false branch, use goto-error
label as fail path.
Maybe better to look at this patch with diff -w -b.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAX_NR_CONSOLES and MAX_NR_USER_CONSOLES are both 63 since they were
introduced in 1.1.54. And since vc_allocate does:
if (currcons >= MAX_NR_CONSOLES)
return -ENXIO;
if (!vc_cons[currcons].d) {
if (currcons >= MAX_NR_USER_CONSOLES && !capable(CAP_SYS_RESOURCE))
return -EPERM;
}
the second check is pointless. Remove both the check and the macro
MAX_NR_USER_CONSOLES.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msm_find_best_baud() function is written with the assumption
that the port->uartclk rate is fixed to a particular rate at boot
time, but now this driver changes that clk rate at runtime when
the baud is changed.
The way the hardware works is that an input clk rate comes from
the clk controller into the uart hw block. That rate is typically
1843200 or 3686400 Hz. That rate can then be divided by an
internal divider in the hw block to achieve a particular baud on
the serial wire. msm_find_best_baud() is looking for that divider
value.
A few things are wrong with the way the code is written. First,
it assumes that the maximum baud that the uart can support if the
clk rate is fixed at boot is 460800, which would correspond to an
input clk rate of 230400 * 16 == 3686400 Hz. Except some devices
have a boot rate of 1843200 Hz or max baud of 115200, so
achieving 230400 on those devices doesn't work at all because we
don't increase the clk rate unless max baud is 460800.
Second, we can't achieve bauds higher than 460800 that require
anything besides a divisor of 1, because we always call
msm_find_best_baud() with a fixed port->uartclk rate that will
eventually be changed after we calculate the divisor. So if we
need to get a baud of 500000, we'll just multiply that by 16 and
hope that the clk can give us 500000 * 16 == 8000000 Hz, which it
typically can't do. To really achieve 500000 baud, we need to get
an input clk rate of 24000000 Hz and then divide that by 3 inside
the uart hardware.
Finally, we return success for bauds even when we can't actually
achieve them. This means that when the user asks for 500000 baud,
we actually get 921600 right now, but the user doesn't know that.
Fix all of this by searching through the divisor and clk rate
space with a combination of clk_round_rate() and baud
calculations, keeping track of the best clk rate and divisor we
find if we can't get an exact match. Typically we can get an
exact match with a divisor of 1, but sometimes we need to keep
track and try more frequencies. On my msm8916 device, this
results in all standard bauds in baud_table being supported
except for 1800, 576000, 1152000, and 4000000.
Fixes: 850b37a71b ("tty: serial: msm: Remove 115.2 Kbps maximum baud rate limitation")
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Cc: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Cristian Prundeanu <cprundea@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable reporting of DSR events (which is named DTR in the registers
because Freescale uses the names as seem from a DCE).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to tty_ioctl(4) (from man-pages 4.04) the rng member only
counts 0->1 transitions. For the other signals (DSR, CD, CTS) both edges
are supposed to be counted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that events that are not handled in the irq function don't
trigger an interrupt.
When the serial port is operated in DTE mode, the events for DCD and RI
events are enabled after a system reset by default.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gives the irq core a chance to disable the serial interrupt in case
an event isn't cleared in the handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in DTE mode, the bit USR2_RIIN is active low. So invert the logic
accordingly.
Fixes: 90ebc48386 ("serial: imx: repair and complete handshaking")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add __init attribute on a function that is only called from other __init
functions and that is not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the function is put in the
.text.unlikely segment. Declaring it as __init will cause it to be put in
the .init.text and to disappear after initialization.
The result of objdump -x on the function before the change is as follows:
000000000000014c l F .text.unlikely 0000000000000a2e init_r_port
And after the change it is as follows:
0000000000000000 l F .init.text 0000000000000a29 init_r_port
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alphascale ASM9260 uart IP has some common registers with
Freescale STMP37XX. This patch provide changes which
allow to reuse mxs-auart.c code for ASM9260.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SC16is7xx has feature for auto hardware flow control using RTS/CTS,
so we don't need "uart_handle_cts_change" to invoke "start_tx/stop_tx"
for flow control.
In addition, for software CTS, interrupt "SC16IS7XX_IIR_CTSRTS_SRC"
just report the nCTS change of state from active(low) to inactive(high),
driver don't know when the state of nCTS change from incactive to active,
so can't resume the transmission when a peer device is again ready and
re-assert nRTS signal.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some RS-232 to RS-485 transceivers require Rx to be disabled on Tx to
avoid echo of Tx data into the Rx buffer. Specifically, the XR3160E
RS-232/RS-485/RS-422 transceiver behaves this way.
This commit disables Rx on active Tx when SER_RS485_ENABLED is active and
SER_RS485_RX_DURING_TX is disabled.
Note that this is a change in behavior of the driver. Until now
SER_RS485_RX_DURING_TX was enabled unconditionally even when disabled in
the TIOCSRS485 ioctl serial_rs485 flags field.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling support for the UART on Marvell EBU SoCs only make sense when
compiling for Marvell EBU SoCs, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_MVEBU_UART
drivers/tty/serial/Kconfig: bool "Marvell EBU serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since the code wasn't using module_init to begin with, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to set .owner here. The core will do it.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split off the bulk of the existing meson_serial_console_write()
implementation into meson_serial_port_write() for implementing
meson_serial_early_console_write().
Use "meson" as the earlycon driver name, courtesy of Nicolas.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue with setting up a fixed clock rate at probe is that it would
overwrite the console rate set by the bootloader for its console device.
This would result in serial out corruption or missing log when we system
is booted with earlycon. This is not a issue if we boot system without
earlycon.
This setup is at least not required with the mainline driver, this code
used to be required because the clk_enable() call would fail if
clk_set_rate() wasn't called first.
Originally the issue was noticed on DB410c which is based on APQ8016
chipset.
Without this patch the console log with earlycon would look like:
...
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=1
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
����+HH��0.699378] console [ttyMSM0] enabled
[ 0.699378] console [ttyMSM0] enabled
[ 0.702003] bootconsole [uart0] disabled
[ 0.702003] bootconsole [uart0] disabled
...
with this patch I can see all the skipped lines on the console
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
noctty was removed as a parameter by commit 11e1d4aa4d
("tty: Consolidate noctty check in tty_open()").
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY_NUMBER() has been unused since v2.5.71; removed by
"[PATCH] callout removal: callout is gone".
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tty operations which may expect uart port to have been removed
but still have other necessary work to accomplish, check for NULL
uart port; specifically uart_close(), uart_hangup() and sub-functions
(uart_shutdown() and uart_port_shutdown()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For serial core operations not already excluded by holding port->mutex,
use reference counting to protect deferencing the state->uart_port.
Introduce helper functions, uart_port_ref() and uart_port_deref(), to
wrap uart_port access, and helper macros, uart_port_lock() and
uart_port_unlock(), to wrap combination uart_port access with uart
port lock sections.
Port removal in uart_remove_one_port() waits for reference count to
drop to zero before detaching the uart port from struct uart_state.
For functions only reading the tx circular buffer indexes (where the
uart port lock is claimed to prevent concurrent users), a NULL uart
port is simply ignored and the operation completes normally.
For functions change the tx circular buffer indexes (where the uart
port lock is claimed to prevent concurrent users), the operation is
aborted if the uart port is NULL (ie., has been detached).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_remove_one_port() may race with every serial core operation
requiring a valid dereference of state->uart_port. In particular,
uart_remove_one_port() may unlink the uart port concurrently with
any serial core operation that may dereference same.
Ensure safe dereference for those operations that already claim
the port->mutex, and extend that guarantee for trivial cases,
such as the ioctl handlers. Introduce the uart_port_check() helper
which asserts port->mutex is held (only when lockdep is on).
For ioctls, return -EIO as if the port has been hung up (since it has).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare uart_poll_init() to safely dereference uart port; expand the
port mutex section to guarantee uart port remains valid until
uart_poll_init() completes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASYNC*_SHARE_IRQ is no longer used; remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_SUSPENDED bit in the tty_port::flags field with
TTY_PORT_SUSPENDED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_suspended() and tty_port_suspended() to abstract
atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_CHECK_CD bit in the tty_port::flags field with
TTY_PORT_CHECK_CD bit in the tty_port::iflags field. Introduce helpers
tty_port_set_check_carrier() and tty_port_check_carrier() to abstract
the atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_NORMAL_ACTIVE bit in the tty_port::flags field with
TTY_PORT_ACTIVE bit in the tty_port::iflags field. Introduce helpers
tty_port_set_active() and tty_port_active() to abstract atomic bit ops.
Extract state changes from port lock sections, as this usage is
broken and confused; the state transitions are protected by the
tty lock (which mutually excludes parallel open/close/hangup),
and no user tests the active state while holding the port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_CTS_FLOW bit in the tty_port::flags field with
TTY_PORT_CTS_FLOW bit in the tty_port::iflags field. Add
tty_port_set_cts_flow() helper to abstract the atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abstract TTY_IO_ERROR status test treewide with tty_io_error().
NB: tty->flags uses atomic bit ops; replace non-atomic bit test
with test_bit().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Version 2 of the Server Base System Architecture (SBSAv2) describes UART
hardware registers as 32 bits wide, giving no guidance on access sizes. The
SBSA UART driver previously assumed partial-length 16 and 8 bit accesses would
work. But the SBSAv2 UART hardware on the Qualcomm Technologies QDF2432 only
supports full-length 32 bit register accesses, so use those exclusively. This
is compatible with SBSAv3, which explicitly requires UART hardware support 32
(and 16 and sometimes 8) bit accesses.
Tested on Juno, Midway, QDF2432, Seattle, and X-Gene 1.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Cc: stable <stable@vger.kernel.org> # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 21947ba654 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654 ("serial: 8250_pci: replace switch-case by formula")
Cc: stable@vger.kernel.org
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is more prep-work for the upcoming pty changes. Still just code
cleanup with no actual semantic changes.
This removes a bunch pointless complexity by just having the slave pty
side remember the dentry associated with the devpts slave rather than
the inode. That allows us to remove all the "look up the dentry" code
for when we want to remove it again.
Together with moving the tty pointer from "inode->i_private" to
"dentry->d_fsdata" and getting rid of pointless inode locking, this
removes about 30 lines of code. Not only is the end result smaller,
it's simpler and easier to understand.
The old code, for example, depended on the d_find_alias() to not just
find the dentry, but also to check that it is still hashed, which in
turn validated the tty pointer in the inode.
That is a _very_ roundabout way to say "invalidate the cached tty
pointer when the dentry is removed".
The new code just does
dentry->d_fsdata = NULL;
in devpts_pty_kill() instead, invalidating the tty pointer rather more
directly and obviously. Don't do something complex and subtle when the
obvious straightforward approach will do.
The rest of the patch (ie apart from code deletion and the above tty
pointer clearing) is just switching the calling convention to pass the
dentry or file pointer around instead of the inode.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here are 3 serial driver fixes for issues that have been reported. Two
are reverts, fixing problems that were in the big TTY/Serial driver
merge in 4.6-rc1, and the last one is a simple bugfix for a regression
that showed up in 4.6-rc1 as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcbSMkACgkQMUfUDdst+ymBkACgqvOCijwdNr0MrvU2/zxdJYNJ
3EEAnjrQUvDVqMPem9fiR9Y7I1iGPYNx
=Ux5a
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are 3 serial driver fixes for issues that have been reported.
Two are reverts, fixing problems that were in the big TTY/Serial
driver merge in 4.6-rc1, and the last one is a simple bugfix for a
regression that showed up in 4.6-rc1 as well.
All have been in linux-next with no reported issues"
* tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: Add hardware dependency to RT288X option"
tty/serial/8250: fix RS485 half-duplex RX
Revert "serial-uartlite: Constify uartlite_be/uartlite_le"
This reverts commit 8d2acdb9fc.
It's causing problems, and somehow I missed that Peter didn't like it at
all :(
So revert it for now until it gets sorted out.
Reported-by: Mason <slash.tmp@free.fr>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
When in half-duplex mode RX will be disabled before TX, but not
enabled after deactivating transmitter. This patch enables
UART_IER_RLSI and UART_IER_RDI interrupts after TX is over.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Acked-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of the horrible notion of having that
struct inode *ptmx_inode
be the linchpin of the interface between the pty code and devpts.
By de-emphasizing the ptmx inode, a lot of things actually get cleaner,
and we will have a much saner way forward. In particular, this will
allow us to associate with any particular devpts instance at open-time,
and not be artificially tied to one particular ptmx inode.
The patch itself is actually fairly straightforward, and apart from some
locking and return path cleanups it's pretty mechanical:
- the interfaces that devpts exposes all take "struct pts_fs_info *"
instead of "struct inode *ptmx_inode" now.
NOTE! The "struct pts_fs_info" thing is a completely opaque structure
as far as the pty driver is concerned: it's still declared entirely
internally to devpts. So the pty code can't actually access it in any
way, just pass it as a "cookie" to the devpts code.
- the "look up the pts fs info" is now a single clear operation, that
also does the reference count increment on the pts superblock.
So "devpts_add/del_ref()" is gone, and replaced by a "lookup and get
ref" operation (devpts_get_ref(inode)), along with a "put ref" op
(devpts_put_ref()).
- the pty master "tty->driver_data" field now contains the pts_fs_info,
not the ptmx inode.
- because we don't care about the ptmx inode any more as some kind of
base index, the ref counting can now drop the inode games - it just
gets the ref on the superblock.
- the pts_fs_info now has a back-pointer to the super_block. That's so
that we can easily look up the information we actually need. Although
quite often, the pts fs info was actually all we wanted, and not having
to look it up based on some magical inode makes things more
straightforward.
In particular, now that "devpts_get_ref(inode)" operation should really
be the *only* place we need to look up what devpts instance we're
associated with, and we do it exactly once, at ptmx_open() time.
The other side of this is that one ptmx node could now be associated
with multiple different devpts instances - you could have a single
/dev/ptmx node, and then have multiple mount namespaces with their own
instances of devpts mounted on /dev/pts/. And that's all perfectly sane
in a model where we just look up the pts instance at open time.
This will eventually allow us to get rid of our odd single-vs-multiple
pts instance model, but this patch in itself changes no semantics, only
an internal binding model.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit e9036d0662 ("tty: Drop krefs for interrupted tty lock")
fixed a tty reference counting problem introduced in
commit 0bfd464d3f ("tty: Wait interruptibly for tty lock on reopen"),
so v4.5.0 is correct.
However, commit d6203d0c7b ("tty: Refactor tty_open()") moved the
relevant code for 4.6-rc1; correct the merge.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User-Mode Linux supplies an alternate TTY_MAJOR driver for stdio console,
so the noctty check in tty_open() must apply only to VT driver tty0
devnode and not the UML console driver tty0 devnode.
Fixes: 11e1d4aa4d ("tty: Consolidate noctty checks in tty_open()")
Reported-by: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Make earlyprintk=xen work for HVM guests.
- Remove module support for things never built as modules.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8YhlAAoJEFxbo/MsZsTRiCgH/3GnL93s/BsRTrA/DYykYqA4
rPPkDd6WMlEbrko6FY7o4IxUAZ50LWU8wjmDNVTT+R/VKlWCVh2+ksxjbH8e0nzr
0QohAYTdG1VGmhkrwTjKj0wC3Nr8vaDqoBXAFRz4DiQdbobn12wzXjaVrbl8RRNc
oHDqR+DfZj6ontqx8oFkkTk7CFKIGEOtm/uBhCAV2fNkQSUCzuQyKLlarxM6jq/2
EnLR1bhnyoy5zNFzXxmaJgZOit8QFMKvPdDRknlp9yDHYJ5zolJkv+6FPiAG6SZs
A8yAUPQoAD+ekAiV2DIhb8qoNNNdZXdRCFBpoudwX3GyyU4O2P5Intl0xEg17Nk=
=L8S4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.6:
- Make earlyprintk=xen work for HVM guests
- Remove module support for things never built as modules"
* tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: make platform-pci.c explicitly non-modular
drivers/xen: make sys-hypervisor.c explicitly non-modular
drivers/xen: make xenbus_dev_[front/back]end explicitly non-modular
drivers/xen: make [xen-]ballon explicitly non-modular
xen: audit usages of module.h ; remove unnecessary instances
xen/x86: Drop mode-selecting ifdefs in startup_xen()
xen/x86: Zero out .bss for PV guests
hvc_xen: make early_printk work with HVM guests
hvc_xen: fix xenboot for DomUs
hvc_xen: add earlycon support
CONFIG_SERIAL_8250_RSA has waited for a long
time to have meaningful help text so let's
finally describe what this option actually does.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch optimizes UART rx fifo access routine by reading UART SFR
when necessary. At first, the "fifocnt" variable will be initialized
as Rx FIFO count. So we don't need to access UFSTAT(FIFO status) register
every time to check FIFO count because we know that count with "fifocnt".
After all data were read out from Rx FIFO, the "fifocnt" will be set as 0.
Lastly, UFSTAT will be accessed again to check whether the data remains
by any chance.
Signed-off-by: Youngmin Nam <ym0914@gmail.com>
Reviewed-by: Jung-Ick Guack <ji.guack@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PL011 UART has hardware mark/space parity ability, this trivial patch adds support for it.
Tested on Raspberry Pi v1, v2 (BCM2835 and BCM2836)
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
up_to_u8250p() casts struct uart_port * to struct uart_8250_port *. Update code
to use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Mediatek 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `mtk8250_set_termios':
:(.text+0x1bee8): undefined reference to `serial8250_do_set_termios'
:(.text+0x1bf10): undefined reference to `uart_get_baud_rate'
:(.text+0x1c09c): undefined reference to `uart_get_divisor'
drivers/tty/built-in.o: In function `mtk8250_do_pm':
:(.text+0x1c0d0): undefined reference to `serial8250_do_pm'
drivers/tty/built-in.o: In function `mtk8250_probe':
:(.text+0x1c2e4): undefined reference to `serial8250_register_8250_port'
serial/8250/8250_mtk.c:287:242: error: data definition has no type or storage class [-Werror]
serial/8250/8250_mtk.c:287:122: error: 'mtk8250_platform_driver_init' defined but not used [-Werror=unused-function]
This changes the symbol to a 'tristate', so the dependency on
SERIAL_8250 also works when that is set to 'm'.
To actually build the driver, we also need to include <linux/module.h>.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Ingenic 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `ingenic_uart_probe':
8250_ingenic.c:(.text+0x1c1a0): undefined reference to `serial8250_register_8250_port'
This changes the symbol to a 'tristate', plus a dependency on
SERIAL_8250, which makes it work again. Unlike the other
soc-specific backends, this one has no dependency on an
architecture or a platform. I'm adding a dependency on
MIPS || COMPILE_TEST as well here, to avoid showing the driver
on architectures that are not interested in it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added uniphier serial port driver fails to build as
a loadable module when the base 8250 driver is built-in and
its console support enabled:
ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!
This changes the driver to only provide the early console support
if it is built-in itself as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cafe1ac640 ("drivers/tty: make serial
8250_ingenic.c explicitly non-modular"), which attempted to remove dead
code but did not have the desired effect when the main 8250 driver was
a loadable module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d72d391c12 ("drivers/tty/serial: make
8250/8250_mtk.c explicitly non-modular"), which intended to remove dead
code but did not have the desired effect when the main 8250 driver was
a module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Armada-3700's uart is a simple serial port, which doesn't
support. Configuring the modem control lines. The uart port has a 32
bytes Tx FIFO and a 64 bytes Rx FIFO
The uart driver implements the uart core operations. It also support the
system (early) console based on Armada-3700's serial port.
Known Issue:
The uart driver currently doesn't support clock programming, which means
the baud-rate stays with the default value configured by the bootloader
at boot time
[gregory.clement@free-electrons.com: Rewrite many part which are too long
to enumerate]
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the mctrl_gpio driver can be built as a module, it needs to have its
license specified with MODULE_LICENSE. Otherwise, it cannot access
required symbols exported through EXPORT_SYMBOL_GPL.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc warns about a potential use of an uninitialized variable in this driver:
drivers/tty/serial/ifx6x60.c: In function 'ifx_spi_complete':
drivers/tty/serial/ifx6x60.c:713:6: warning: 'more' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (more || ifx_dev->spi_more || queue_length > 0 ||
Unlike a lot of other such warnings, this one is correct and describes
an actual problem in the handling of the "IFX_SPI_HEADER_F" result code.
This appears to be a result from a restructuring of the driver that
dates back to before it was merged in the kernel, so it's impossible
to know where it went wrong. I also don't know what that result code
means, so I have no idea if setting 'more' to zero is the correct
solution, but at least it makes the behavior reproducible rather than
depending on whatever happens to be on the kernel stack.
This patch initializes the 'more' variable to zero in each of the
three code paths that could result in undefined behavior before,
which is more explicit than initializing it at the start of the
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With SAMA5D2, the UART has hw timeout but the offset of the register to
define this value is not the same as the one for USART.
When using the new UART, the value of this register was 0 so we never
get timeout irqs. It involves that when using DMA, we were stuck until
the execution of the dma callback which happens when a buffer is full
(so after receiving 2048 bytes).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c39dfebc77, the modular support
code for atmel_serial was removed, as the driver cannot be built as a
module. Because no use case was proposed, the dynamic driver binding
support was removed as well.
The atmel_serial driver can manage up to 7 serial controllers, which are
multiplexed with other functions. For example, in the Atmel SAMA5D2, the
Flexcom controllers can work as USART, SPI or I2C controllers, and on
all Atmel devices serial lines can be reconfigured as GPIOs.
My use case uses GPIOs to transfer a firmware update using a custom
protocol on the lines used as a serial port during the normal life of
the device. If it is not possible to unbind the atmel_serial driver, the
GPIO lines remain reserved and prevent this case from working.
This patch reinstates the atmel_serial_remove function, and fixes it as
it failed to clear the "clk" field on removal, triggering an oops when
a device was bound again after being unbound.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kconfig option SERIAL_8250_RT288X seems to be only relevant on MIPS
platforms, so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the platform bus sets the platform_device id to -1 (PLATFORM_DEVID_NONE),
use an incrementing counter for the TTY index instead
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable support for registering this device using the device tree.
Device tree node example for registering Goldfish TTY device :
goldfish_tty@1f004000 {
interrupts = <0xc>;
reg = <0x1f004000 0x1000>;
compatible = "google,goldfish-tty";
};
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device generates a short rising pulse on the interrupt request line.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Better to hold the spinlock as short as possible.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is ideal to use when you need a lot of uarts in your FPGA.
Try not to force all those users to patch their kernel.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have channel offset defined since all BayTrail and Braswell
ports are 1 channel. Remove unneeded definition.
While here, remove comment which has no value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The managed API provides a better approach to help with acquiring and releasing
resources. Besides that error handling becomes simpler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are managed through clk-fractional-divider.c module, and thus CLK
framework takes care about it. Remove letfovers from this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the main branch contains return statement the 'else' keyword is not
needed. Remove it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chuah, Kim Tatt