The driver also contains a piece of configuration data that produces a
one line description of the specific hardware being driver
(e.g. "Hauppauge 24xxx", "OnAir", etc). This change generates an
informational message to the kernel log reporting the hardware type
being driven. This is a very useful thing to know when diagnosing
problems.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It used to be that the only real detectable reason for the driver to
fail during initialization would be that if the hardware is simply
jammed. However with the advent of the sub-device mechanism in V4L it
is possible now to detect if a sub-device module fails to load
successfully. The pvrusb2 driver does in fact react to this by also
(correctly) failing, however the original diagnostic message "hardware
is jammed" was still being reported. This misleads the user because
in fact it might not actually be a hardware failure. This change adds
logic to tell the difference and then report a more appropriate
message to the kernel log.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Encoder failures are mostly recoverable by the driver. While
it would sure be nice not to have the failure happen in the first
place, this has been going on for years and I doubt that a real
solution will ever present itself. I think that part's firmware is
just slightly flakey and we have to deal with it. The driver does
deal with it just fine, but the warning message going into the kernel
log is probably a little more alarming than it should be. So try to
soften up the warning somewhat.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Associate V4L device node in sysfs with the underlying USB
device. This opens the door to device information tracking in udev
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
consolidate common code used to determine if calibration on startup is needed
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If rf_cal_on_startup is enabled in the structure passed into
tda18271_attach, and the cal module option isn't disabled, then we
should run the initialization and calibration procedures during the
tda18271_attach function call, regardless of how many instances of the
driver have been attached. If the device is already calibrated, the
driver will detect that and will only calibrate again if necessary.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If rf_cal_on_startup is enabled in the structure passed into
tda18271_set_config, and the cal module option isn't disabled,
then we should run the initialization and calibration procedures
during the tda18271_set_config function call.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the set_config method to allow drivers to configure the
tda18271 driver options after attach.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is already an option for sending 16 byte chunks rather that writing
39 bytes all at once during the tuner's initialization. Some i2c buses
can't send 16 bytes at once, so create an option for sending 8 byte chunks.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Terry Wu for finding the GPIOs required for svideo / composite input
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
on the slave tuner, only. The master tuner must always leave
slave tuner output / loop thru enabled.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add flip/mirror support for OV2640
- fix for backlight value range
- fix for red-blue inversion hue mode with V4L1 applications
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original implementation of pac_find_sof() does not always find
the Start Of Frame (SOF) marker. Replace it with a state machine
based design.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xc5000 tuning attempts shouldn't return zero in the case where the firmware
did not load successfully.
Thanks to Michael Krufky for pointing out this issue.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for saturation/hue controls, prompted by errors showing up in
the mythbackend log.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca: Don't resubmit error status URB's when suspending
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gscpa core was not resubmitting URB's when the URB status was an error,
this means we will loose URB's (potentially all stopping the stream) in
case of sporadic USB issues. I've seen this with an Aiptek stv0680 based
PenCam connected through an USB 2.0 hub.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a new subdriver to gspca supporting cams with the stv0680
bridge (replacing the old in kernel v4l1 driver).
Many thanks to Hans Verkuil for providing me with one of the 2 cams used in
testing this new sub driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca w9968cf: slight tweak to vstart and hstart to get rid of black borders
in 640x480 mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca w9968cf: Add support for JPEG compression, this enables much higher
framerates at 320x240 / 352x288 and also allows for 640x480 mode for
cams which can do this. The w9968cf uses planar JPEG, which libv4l until
now did not support, so this requires atleast version 0.6.3 of libv4l.
And something important I forgot to mention in my earlier w9968cf commits:
Many thanks to Hans Verkuil for giving me a w9968cf based cam, which has
allowed me to develop the gspca w9968cf support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca-w9968cf: Don't add an extra packet to the buffer after the EOF,
this makes the frame data size bigger then it should be which makes
gstreamer discard it.
This patch also fixes an unrelated compiler warning.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cache sensor regs to avoid unnecessary slow i2c reads / writes, this speeds
up sd_start a bit with most bridges and a lot (from 5 seconds down to 0.3
seconds) with W996xCF cams, as this avoids very slow bit bang IO over
USB i2c reads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support to gspca for the Winbond W9967CF and W9968CF
camera's. This is mostly a port of the existing v4l1 driver to gspca
(making it v4l2). But this also features fixes to the bitbanging i2c code
(send a nack not an ack after reading the last byte of a transfer), which
gets rid of the weird errors which were being seen there, and of
the smbus_refresh() hack to get around these errors.
Also the vstart settings have been tweaked to work with different
frequency filter settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.
It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the I2C device provides an interrupt it is registered and the
standard
is updated via interrupts rather than polling.
Since I2C communication is needed, the interrupt handler fires off a
work which will check the new standard, and store it in the internal
structure.
To handle mutual exclusion a mutex is introduced.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch defines the probe and remove function as __devinit and __devexit.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for settings the input standard of the ADV7180.
When the input standard is set there is no use to ask the
chip for standard, therefore it is cached in the driver.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support to the ADV7180 driver to check the input
status.
Since the status is held in the same register as the input standard
a small restructuring of the code is done to reuse the code for
reading the register
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds the device IDs and driver linking to allow the Asus Europa DVB-T
card to operate with these drivers.
The device has a SAA7134 chipset with a TD1316 Hybrid Tuner.
All inputs work on the card including switching between DVB-T and
Analogue TV, there is also no IR with this card.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Danny Wood <danwood76@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The definition of tvaudio_tuner_ops initializes the s_tuner field twice.
It appears that the second case should initialize the g_tuner field.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the image size (bytesperline*height) is not multiple
of PAGE_SIZE, v4l2 rounded the required buffer size to
be multiple of PAGE_SIZE. This prevented user space
to store images directly into userptr buffers which were
not multiple of PAGE_SIZE. This constraint is removed.
The start address is still assumed to be required
page-aligned, ie., when v4l2 allocates mmap buffers,
the offset between different buffers is page-aligned.
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default streaming control timeout was found by Ondrej Zary to be too low
for some Logitech webcams. With kernel 2.6.22 and newer they would timeout
during initialization unles the audio function was initialized before the
video function.
Add a module parameter to set the streaming control timeout and increase the
default value from 1000ms to 3000ms to fix the above problem.
Thanks to Ondrej Zary for investigating the issue and providing an initial
patch.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least one 5986:0241 webcam model includes vendor-specific descriptors
at the end of its streaming interface descriptors. Print an information
UVC_TRACE_DESCR message and try to continue parsing the descriptors
rather than bailing out with an error.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch sets stream->urb_size as psize*npackets
before calling uvc_alloc_urb_buffers, which may fix
a possible failure of usb_buffer_free in case usb_buffer_alloc
returns NULL. The patch is based on the ideas below:
1,If usb_buffer_alloc can't allocate a buffer sucessfully,
uvc_free_urb_buffers will be called to free the allocated
buffers, and stream->urb_size is required to be passed to
usb_buffer_free;
2,uvc_free_urb_buffers can reset stream->urb_size.
This patch is against linux-v2.6.31-next-20090926.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver has a driver-wide lock and a reference count to protect
against a disconnect/open race. Now that videodev handles the race itself,
reference-counting in the driver can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dismiss privileges on the file handle when calling VIDIOC_REQBUFS with a
buffer count of 0. This allows applications to release the streaming
permissions on the file handle without closing it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_TRY_FMT ioctl doesn't interfere with video streaming and thus
should succeed on an unprivileged file handle.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the trace level for messages related to video URB buffers allocation and
alternate setting selection.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return minimum, maximum and step set to 0 without querying the hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were various "if (sensor == foo)" pieces of code inside ov519.c,
move these bits to the sensor specific init functions, where they
belong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_ov519: add support for the ovfx2 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the OV2610 and OV3610 sensors to the gspca
ov519 subdriver. This is a preparation patch for adding ovfx2 bridge
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CIF sensor type 1 exposure setting got clamped at 300, as settings below
300 do not work well (and do work for the other sensors). This patch
scales the 0-4095 range to 300-4095 instead of ignoring changes between
300, avoiding have a part of the control range where nothing happens.
This is esp. important for software autogain as done by libv4l.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While checking all gspca sub drivers pkt_scan functions for a bug I found in
1 of them (and after checking also in another), I noticed a bug in the
gspca_sq905c work queue function, once it has decided to start discarding a
frame because the application is not reading fast enough (and thus returning
buffers to fill fast enough), it never stops discarding.
This patch fixes this by simply completely removing the "discarding"
variable, if we need to discard the current frame because there is no buffer
to store it, the "frame" pointer will be NULL, so that is all we need to
check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While checking all gspca sub drivers pkt_scan functions for a bug I found in
1 of them (and after checking also in another), I noticed a bug in the
gspca_jeilinj work queue function, once it has decided to start discard a
frame because the application is not reading fast enough (and thus returning
buffers to fill fast enough), it never stops discarding.
This patch fixes this by simply completely removing the "discarding"
variable, if we need to discard the current frame because there is no buffer
to store it, the "frame" pointer will be NULL, so that is all we need to
check.
I've also moved the gspca_get_i_frame() call and the writing of the jpg
header to the buffer to after the first usb_bulk_msg() call, as we don't
need it before that, and that will give the app slightly more time to
queue a buffer for us to fill.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve (and also simplify :) gspca_mr97310a: VGA sensor type detection.
As it was still failing on some machines (not with some cams, but on
some machines interesting enough).
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Remove use of unneeded discarding variable
-Cleanup locking to only take usb_lock around access to the control
endpoint, by no longer taking the lock around the bulk transfer
(which takes most of the time) we can remove the msleep(1) which was
needed to give the gspca core a chance to grab the usb_lock to signal
us to stop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds controls for vga cams with sensor type 0, in order to
correctly report the present controls, the probing of the sensor type
has been moved from sd_start to sd_config, since this made the sensor
type probing unreliable the detection method was changed.
Note this requires the camera to enter streaming mode, so sd_config now
briefly makes the camera stream.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as TeVii S460,S420.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.
create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If CEU driver can not receive data from camera,
CETCR has VBP error state.
Then, CEU is stopped and cure operation is needed.
This patch add VBP error cure operation.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add comment about the meaning of the fixed JPEG header bytes used to
create each image.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The length check in reg_w_var() function is because the buffer contents
is copied to gspca_dev->usb_buf which has the size of USB_BUF_SZ bytes as
defined in drivers/media/video/gspca/gspca.h. Replace the number with
symbol for better readability and maintainability.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32.
Convert tda18271_priv.tm_rfcal from unsigned int to u8.
Cast subtractions between u32 values as s32.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use temporary variables for signed calulations between unsigned values
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a forgotten module_param macro needed to set a deemphasis of 50us.
It is the standard setting for commercial FM radio broadcasts outside the US.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
override set_frontend to allow rf input path switching on the HVR1275
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes adds IR Rx keypress input event handling to the CX23885 module.
This change specifically only adds input handling for IR devices implemented as
v4l2_subdevices, using only the pulse width mode (for now), and only with
RC-5 remotes. The V4L-DVB infrastructure is missing too much to support RC-6
mode 6A as used in many media center remotes. The grey Hauppauge RC-5 remote
and HVR-1850 IR receiver work now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add integrated IR subdevice interrupt and notification handling. This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change completes the v4l2_subdev implementation for IR receive for the
IR controller built into the CX23888.
This changes almost completes the IR transmit side also, but doesn't. Instead
notes in the comments describe what needs to be done for IR Tx to work in the
subdevice implementation.
The current Tx behavior is skeletal and benign. If left alone, it does nothing.
It will only ever generate a Tx interrupt on Tx init by a caller or when the
tx_write() method is called. The ISR, when called, will then disable the Tx
FIFO service interrupt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prior mechanism wasn't reliable with the cx23887. This new mechanism
tests correctly against cx23885, 7 and 8 based products.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the IR controller on the CX23888 to work for the HVR-1850 and in
general, the A/V core must be initialized to get the VID_CLK going.
The VID_CLK is the timing reference for the CX23888's integrated
IR controller.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SYS and AUX PLLs need to be initialized to different values based on
the chip: CX23885, CX23887, CX23888, as each uses a different crystal
frequency: 28.6363 MHz, 25.0 MHz, 50.0 MHz.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate out the set_audclk_freq() function into separate functions for the
four families of cores. These cores all use slightly different sample clock
schemes and may be assuming slightly (+/- 3 Hz) different reference frequencies.
The code resuse was not worth the maintenance and testing headache of have all
chips use the same function peppered with conditional logic.
Added comments on how PLL and SRC parameters values are computed. Fixed a few
bugs related to the shared code having a large number of conditional statements.
Noted inconsistencies with FIXME in the comments.
This is done in preparation for getting the CX2388[578] PLL/clock setting logic
cleaned up for CX23888 analog video and IR (which need the VID PLL set right).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change logic to check for various chip or core families to inline functions.
Checks for specific chips should be made against the state->id field now. This
is in preparation for chip/core specific code for setting up PLLs for the
CX2388[578] family of cores, that all run with different crystal frequencies.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add improved logic to detect the exact CX2388[578] A/V core that is being
probed. Also cleaned up detection and logging for CX2310[12], CX2583[67],
and CX2584[0123] cores and chips.
Also added code to identify a CX2388[578] A/V decoder core that is not
responding properly. Typical symptoms include registers 0x00-0xff
responding properly but all other registers returning the same value
(0x13 and 0x5 have been observed). This state will cause proper detection of
'885 vs. '887 vs. '888 to fail and the chip won't respond to get configured
properly anyway. I have no method of reseting the core to a working state at
this time; but I didn't try too hard to work one out either. The problem
likely only occurs in development. I suspect configuring the SYS PLL VCO to
oscillate too slowly (286.3 MHz?) before post divide may be the root cause,
when encountered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller. This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.
The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes corrects the ioctl() operations for both the CX2388[578] analog
video and MPEG video device nodes to properly and consistently support
VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s.
This caused some ioctl() support routines to be broken out into a separate
source file.
Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers
including the CX2388[57] functions handled by the cx25840 module.
This was done in anticipation of developing a new v4l2_subdev for the
integrated IR controller of the CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri's patch for the Behold X7 didn't use the #define I had setup for
XC5000_RADIO_FM1, so cut over to using that instead of "1".
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the digital side of the Behold X7
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).
Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros. Between
the two of them, they got all the core functionality working for the device.
Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: Uroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely