When built with debugging support, the Gigaset driver enabled some
debugging messages by default. Change the default to "all off".
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the locking scheme on the fec_mpc52xx driver. This device can
receive IRQs from three sources; the FEC itself, the tx DMA, and the
rx DMA. Mutual exclusion was handled by taking a spin_lock() in the
critical regions, but because the handlers are run with IRQs enabled,
spin_lock() is insufficient and the driver can end up interrupting
a critical region anyway from another IRQ.
Asier Llano discovered that this occurs when an error IRQ is raised
in the middle of handling rx irqs which resulted in an sk_buff memory
leak.
In addition, locking is spotty at best in the driver and inspection
revealed quite a few places with insufficient locking.
This patch is based on Asier's initial work, but reworks a number of
things so that locks are held for as short a time as possible, so
that spin_lock_irqsave() is used everywhere, and so the locks are
dropped when calling into the network stack (because the lock only
protects the hardware interface; not the network stack).
Boot tested on a lite5200 with an NFS root. Has not been performance
tested.
Signed-off-by: Asier Llano <a.llano@ziv.es>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more effective rss hash by default (src + dst, rather than just
src).
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
due to reference counting sk_wmem_alloc now has a value of 1 when all
the outstanding data has been sent.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is an updated version, because ixgbe_get_ethtool_stats()
needs to call dev_get_stats() or "ethtool -S" wont give
correct tx_bytes/tx_packets values.
Several cpus can update netdev->stats.tx_bytes & netdev->stats.tx_packets
in parallel. In this case, TX stats are under estimated and false sharing
takes place.
After a pktgen session sending exactly 200000000 packets :
# ifconfig fiber0 | grep TX
TX packets:198501982 errors:0 dropped:0 overruns:0 carrier:0
Multi queue devices should instead use txq->tx_bytes & txq->tx_packets
in their xmit() method (appropriate txq lock already held by caller, no
cache line miss), or use appropriate locking.
After patch, same pktgen session gives :
# ifconfig fiber0 | grep TX
TX packets:200000000 errors:0 dropped:0 overruns:0 carrier:0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround added for all ESB2 devices (adds a delay for all MDIC accesses
which resolves an issue with the MDIC ready bit being set prematurely) is
applicable only to devices in which the MAC-PHY interconnect is not
operating in a certain mode with in-band MDIO. Check the control register
for the operating mode and enable the workaround accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GG82563_REG() macro should not be used to determine the offset provided
to the e1000e_[read|write]_kmrn_reg() functions since the first argument to
the macro is already implied and gets masked off anyway in the functions.
The resultant register reads/writes with this patch are functionally the
same as before.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 7 in the CTRL_REG register is actually the Software Definable Pin 3,
not the Software Definable Pin 7.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.33' of git://git.kernel.dk/linux-2.6-block: (113 commits)
cfq-iosched: Do not access cfqq after freeing it
block: include linux/err.h to use ERR_PTR
cfq-iosched: use call_rcu() instead of doing grace period stall on queue exit
blkio: Allow CFQ group IO scheduling even when CFQ is a module
blkio: Implement dynamic io controlling policy registration
blkio: Export some symbols from blkio as its user CFQ can be a module
block: Fix io_context leak after failure of clone with CLONE_IO
block: Fix io_context leak after clone with CLONE_IO
cfq-iosched: make nonrot check logic consistent
io controller: quick fix for blk-cgroup and modular CFQ
cfq-iosched: move IO controller declerations to a header file
cfq-iosched: fix compile problem with !CONFIG_CGROUP
blkio: Documentation
blkio: Wait on sync-noidle queue even if rq_noidle = 1
blkio: Implement group_isolation tunable
blkio: Determine async workload length based on total number of queues
blkio: Wait for cfq queue to get backlogged if group is empty
blkio: Propagate cgroup weight updation to cfq groups
blkio: Drop the reference to queue once the task changes cgroup
blkio: Provide some isolation between groups
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
libata: Clarify ata_set_lba_range_entries function
libata: Report zeroed read after TRIM and max discard size
pata_hpt3x2n: fix overclocked MWDMA0 timing
pata_it8213: MWDMA0 is unsupported
[libata] MWDMA0 is unsupported on PIIX-like PATA controllers
pata_via: clear UDMA transfer mode bit for PIO and MWDMA
pata_sis: Power Management fix
pata_rz1000: Power Management fix
pata_radisys: fix UDMA handling
pata_ns87415: Power Management fix
pata_marvell: fix marvell_pre_reset() documentation
pata_legacy: add pointers to QDI65x0 documentation
pata_legacy: fix access to control register for QDI6580
pata_legacy: fix QDI6580DP support
pata_it8213: fix it8213_pre_reset() documentation
pata_it8213: fix wrong MWDMA timings being programmed
pata_it8213: fix PIO2 underclocking
pata_it8213: fix wrong PIO timings being programmed
pata_it8213: fix UDMA handling
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: parport_mfc3 - Not makes it a bool before the comparison.
m68k: don't export static inline functions
fbdev: atafb - add palette register check
m68k: Remove the BKL from sys_execve
m68k: Cleanup linker scripts using new linker script macros.
m68k: Make thread_info.h usable from assembly.
m68knommu: define arch_has_single_step() and friends
m68k: ptrace fixes
m68k: use generic code for ptrace requests
rtc: Add an RTC driver for the Ricoh RP5C01
rtc: Add an RTC driver for the Oki MSM6242
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-stub: Documentation update
i2c-stub: Allow user to disable some commands
i2c-stub: Implement I2C block support
i2c: Refactor for_each callbacks
i2c-i801: Retry on lost arbitration
i2c: Remove big kernel lock from i2cdev_open
ics932s401: Clean up detect function
i2c: Simplify i2c_detect_address
i2c: Drop probe, ignore and force module parameters
i2c: Add missing __devinit markers to old i2c adapter drivers
i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
i2c: Prevent priority inversion on top of bus lock
i2c-voodoo3: Delete
i2c-powermac: Drop temporary name buffer
i2c-powermac: Include the i2c_adapter in struct pmac_i2c_bus
i2c-powermac: Log errors
i2c-powermac: Refactor i2c_powermac_smbus_xfer
i2c-powermac: Reject unsupported I2C transactions
i2c/chips: Move ds1682 to drivers/misc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Add flag for devices capable of generating run-time wake-up events
PM / Runtime: Remove unnecessary braces in __pm_runtime_set_status()
PM / Runtime: Make documentation of runtime_idle() agree with the code
PM / Runtime: Ensure timer_expires is nonzero in pm_schedule_suspend()
PM / Runtime: Use deferred_resume flag in pm_request_resume
PM / Runtime: Export the PM runtime workqueue
PM / Runtime: Fix lockdep warning in __pm_runtime_set_status()
PM / Hibernate: Swap, use KERN_CONT
PM / Hibernate: Shift remaining code from swsusp.c to hibernate.c
PM / Hibernate: Move swap functions to kernel/power/swap.c.
PM / freezer: Don't get over-anxious while waiting
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Set UTS_MACHINE correctly.
sparc,leon: init_leon srmmu cleanup
sparc32: Remove early interrupt enable.
sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
sparc64: Faster early-boot framebuffer console.
Revert "sparc: Make atomic locks raw"
sparc: remove unused nfsd #includes
sparc: Fixup last users of irq_chip->typename
Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
No auxio on LEON
apbuart: Use of_find_node_by_path to find root node.
sparc: Replace old style lock initializer
sparc: Make atomic locks raw
apbuart: Fix build and missing driver unregister.
apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
apbuart: Fix build warning.
sparc: Support for GRLIB APBUART serial port
watchdog: Remove BKL from rio watchdog driver
sparc: Remove BKL from apc
sparc,leon: Sparc-Leon SMP support
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Adds support for the WiFi activity LED on the Dell Vostro A860 laptop.
Signed-off-by: Shahar Or <shahar@shahar-or.co.il>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A KERN_DEBUG didn't get removed when transitioning from printk to
pr_debug
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are different bits used to convey the setting of the rfkill
switch to the driver. The current driver only supports one of these
possibilities. These changes were derived from the latest version
of the vendor driver.
This patch fixes the regression noted in kernel Bugzilla #14743.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Antti Kaijanmäki <antti@kaijanmaki.net>
Tested-by: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in ath9k's tx status check, which
caused mac80211 to consider regularly transmitted unicast frames
as un-acked.
When checking the ts_status field for errors, it needs to be masked
with ATH9K_TXERR_FILT, because this field also contains other fields
like ATH9K_TX_ACKED.
Without this patch, AP mode is pretty much unusable, as hostapd
checks the ACK status for the frames that it injects.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FINALIZE_JOIN firmware command only looks at the first couple of
fields in the beacon, and therefore it's not necessary to complain if
the beacon is longer than 128 bytes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disassociating, mac80211 zeroes vif->bss_info.bssid before
calling our ->bss_info_changed(), but we need the BSSID to remove the
hardware station database entry for our AP, so we can't clear our
local copy of the BSSID until after we've done that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to call pci_disable_device() if pci_request_regions()
fails during probe.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index. Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.
Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.
This fixes both of these issues.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field. For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.
We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).
Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.
This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet. It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.
Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.
To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.
In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length. Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise
templates will have incorrect bssid and power save will not work
correctly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a warning from wl1251_op_bss_info_changed():
wl1251: WARNING Set ctsprotect failed 0
It was printed always, it's completely false and can be removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f20941f334.
Sergei Shtylyov notes "You call min() on uncomparables [in
mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and
adev->pio_mode - XFER_PIO_0 yields you a mode number. Thus the second
argument will always "win" as a minimal one"
Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related
to mwdma_clip_to_pio(). The function can return values between 0 and
4 which obviously won't work well for the new code below for values
>2 (i.e. resulting in out-of-bounds array access for the common-case
of dev->pio_mode == XFER_PIO_4)."
Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to
update MWDMA mode masks.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jonathan Cameron reports that building PCMCIA as modules doesn't work:
As module get a load of undefined symbols:
ERROR: "soc_pcmcia_request_irqs" [drivers/pcmcia/pxa2xx_stargate2.ko] undefined!
ERROR: "soc_pcmcia_free_irqs" [drivers/pcmcia/pxa2xx_stargate2.ko] undefined!
ERROR: "soc_pcmcia_enable_irqs" [drivers/pcmcia/pxa2xx_stargate2.ko] undefined!
ERROR: "soc_pcmcia_disable_irqs" [drivers/pcmcia/pxa2xx_stargate2.ko] undefined!
ERROR: "soc_pcmcia_add_one" [drivers/pcmcia/pxa2xx_base.ko] undefined!
ERROR: "soc_common_pcmcia_get_timing" [drivers/pcmcia/pxa2xx_base.ko] undefined!
ERROR: "soc_pcmcia_remove_one" [drivers/pcmcia/pxa2xx_base.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
This is because soc_common tries to be built-in, but it should be a module.
Allow soc_common to be a module.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both iPAQs h3600 and h3100 share the same control
GPIOs for PCMCIA, so driver can be reused.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Combine both headers into one, rename to h3xxx.h and change all
users accordingly.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use of gpio_request/gpio_free in some callbacks may look ugly, but
corresponding drivers (sa1100_serial and sa1100_fb) don't provide (yet)
init/exit hooks and registering these gpios in *_mach_init is also
not possible, because htc-gpio driver starts a bit later...
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert all operations with GPLR/GPCR/GPSR to gpiolibs calls.
Also change all IRQ_GPIO* to gpio_to_irq(*GPIO*)
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a module parameter to override the functionality bitfield. This
lets the user disable some commands. This can be used to force a chip
driver to take different code paths.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Functions i2c_do_add_adapter() and __attach_adapter() do essentially
the same thing, differing only in how the parameters are passed. Same
for i2c_do_add_adapter() and __detach_adapter(). Introduce wrappers to
normalize the parameters, so that we do not have to duplicate the
code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The Intel 82801 is sometimes used on systems with a BMC connected. The
BMC can access the SMBus, resulting in lost arbitration for the 82801.
We should let i2c-core retry transactions for us in this case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The BKL is held over a kmalloc so cannot protect anything beyond that.
The two calls before the kmalloc have their own locking.
Improve device open function by removing the now unnecessary ret variable
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As kind is now hard-coded to -1, there is room for code clean-ups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: "Darrick J. Wong" <djwong@us.ibm.com>
The kind parameter of i2c_detect_address() always has value -1, so we
can get rid of it.
Next step is to update all i2c detect callback functions to get rid of
this now useless parameter.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The legacy probe and force module parameters are obsolete now, the
same can be achieved using the new_device sysfs interface, which is
both more flexible and cheaper (it is implemented by i2c-core rather
than replicated in every driver module.)
The legacy ignore module parameters can be dropped as well. Ignoring
can be done by instantiating a "dummy" device at the problematic
address.
This is the first step of a huge cleanup to i2c-core's i2c_detect
function, i2c.h's I2C_CLIENT_INSMOD* macros, and all drivers that made
use of them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C bus drivers don't have to support I2C_M_REV_DIR_ADDR. It is a
deviation from the I2C specification, which only makes sense to
implement when really needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Low priority thread holding the i2c bus mutex could block higher
priority threads to access the bus resulting in unacceptable
latencies. Change the mutex type to rt_mutex preventing priority
inversion.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@nokia.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Superseded by tdfxfb. I2C/DDC support used to live in a separate
driver but this caused driver conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
We no longer need to write the adapter name to a temporary buffer.
We can write it directly to the i2c_adapter's name field. This is
more efficient.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Include the i2c_adapter in struct pmac_i2c_bus. This avoids memory
fragmentation and allows for several code cleanups.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Log errors when they happen, otherwise we have no idea what went
wrong.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
I wanted to add some error logging to the i2c-powermac driver, but
found that it was very difficult due to the way the
i2c_powermac_smbus_xfer function is organized. Refactor the code in
this function so that each low-level function is only called once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
The i2c-powermac driver doesn't support arbitrary multi-message I2C
transactions, only SMBus ones. Make it clear by returning an error if
a multi-message I2C transaction is attempted. This is better than only
processing the first message, because most callers won't recover from
the short transaction. Anyone wishing to issue multi-message
transactions should use the SMBus API instead of the raw I2C API.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Michel Daenzer <michel@daenzer.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
As i2c/chips is deprecated, move ds1682 to a more apropriate location.
Build tested.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The runtime PM core code assumes that dev->power.timer_expires is
nonzero when the timer is scheduled, but it may become zero
incidentally in pm_schedule_suspend(). Prevent this from happening
by bumping dev->power.timer_expires up to 1 if it's 0 before calling
mod_timer().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
This patch (as1307) adds a small optimization to
__pm_request_resume(). If the device is currently being suspended,
there's no need to queue a work routine to resume it. Setting the
deferred_resume flag will suffice. (There's also a minor improvement
to the function's code layout: An unnecessary "else" is removed.)
Also, the patch clarifies the usage of the deferred_resume flag. It
is meaningful only while a suspend is in progress, so it should be
cleared just before a suspend starts, not just after one ends.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Lockdep complains about taking the parent lock in
__pm_runtime_set_status(), so mark it as nested.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@kernel.org
These now cause errors due to changes present in linux-next:
(__ksymtab_sorted+0x1258): undefined reference to `dio_dev_driver'
(__ksymtab_sorted+0x4d48): undefined reference to `zorro_dev_driver'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add check if palette register number is in correct range
for few drivers which miss it. The regno value comes
indirectly from user space.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
x86, apic: Enable lapic nmi watchdog on AMD Family 11h
x86: Remove unnecessary mdelay() from cpu_disable_common()
x86, ioapic: Document another case when level irq is seen as an edge
x86, ioapic: Fix the EOI register detection mechanism
x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
x86: SGI UV: Map low MMR ranges
x86: apic: Print out SRAT table APIC id in hex
x86: Re-get cfg_new in case reuse/move irq_desc
x86: apic: Remove not needed #ifdef
x86: io-apic: IO-APIC MMIO should not fail on resource insertion
x86: Remove asm/apicnum.h
x86: apic: Do not use stacked physid_mask_t
x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
x86, ioapic: Use snrpintf while set names for IO-APIC resourses
x86, apic: Use PAGE_SIZE instead of numbers
x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
x86: Use EOI register in io-apic on intel platforms
x86: Force irq complete move during cpu offline
x86: Remove move_cleanup_count from irq_cfg
x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
...
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
TOMOYO: Add recursive directory matching operator support.
remove CONFIG_SECURITY_FILE_CAPABILITIES compile option
SELinux: print denials for buggy kernel with unknown perms
Silence the existing API for capability version compatibility check.
LSM: Move security_path_chmod()/security_path_chown() to after mutex_lock().
SELinux: header generation may hit infinite loop
selinux: Fix warnings
security: report the module name to security_module_request
Config option to set a default LSM
sysctl: require CAP_SYS_RAWIO to set mmap_min_addr
tpm: autoload tpm_tis based on system PnP IDs
tpm_tis: TPM_STS_DATA_EXPECT workaround
define convenient securebits masks for prctl users (v2)
tpm: fix header for modular build
tomoyo: improve hash bucket dispersion
tpm add default function definitions
LSM: imbed ima calls in the security hooks
SELinux: add .gitignore files for dynamic classes
security: remove root_plug
SELinux: fix locking issue introduced with c6d3aaa4e3
...
When debugging the wifi firmware, we need to disable the wimax core to gain
some memory space. The default value will keep the wimax core enabled.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wifi and wimax coexistence mode is set by wifi at boot time. There can be
several modes, defined by priority tables. User space components can decide
which one to select by writing to /sys/module/iwmc3200wifi/parameters/wiwi
with this patch, before bringing the interface up.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the wiwi coexistence priority table, we should not tell the LMAC
that we want a response.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This update follows the firmware engineers recommendations.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver version number is a remnant from when there was an out-of-tree
iwlwifi driver. Now that the driver forms part of kernel source we do not
need a separate driver version. Instead, we now use the kernel version as
driver version. We maintain the previous tags used to indicate which
components the driver has been compiled with.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
error_event_table_ptr is only set upon receipt of REPLY_ALIVE. Until
then both event log and error log will fail. Add information to indicate
which uCode encounter the failure case.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the process of improving uCode event logging capability, the new
implementation was introduced without removing the existing
implementation. The event log will be dumped to dmesg twice.
Remove the old implementation to only log the event once upon sys
assert or request by user.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My gcc appears to be able to see past the function
boundary and notices that the variable 'behaviour'
could be used uninitialised:
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_register’:
drivers/net/wireless/b43/leds.c:339: warning: ‘behaviour’ may be used uninitialized in this function
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_init’:
drivers/net/wireless/b43/leds.c:262: warning: ‘behaviour’ may be used uninitialized in this function
because b43_led_get_sprominfo() didn't initialise
it in all cases.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add PCI .shutdown method so that we can disable the device during
shutdown or reboot. Without this, the reboot doesn't work well on
some platforms.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2124
Tested-by: pablo <pablolm2005@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When handling IWM_CMD_PMKID_FLUSH command, the bssid and
pmkid in pmksa are all NULL. Check it before memcpy.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the 2GHz band is enabled unconditionally, even if the device
does not support it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On BigEndian gcc complains:
drivers/net/wireless/airo.c: In function ‘sniffing_mode’:
drivers/net/wireless/airo.c:4809: warning: integer overflow in expression
Fix this by doing the bitwise AND on the host-endian value.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While reviewing the l2pad function to align both the header and the payload
on a DMA-capable boundary a bug was discovered where the payload would not
be properly aligned. The header_align value was used where the payload_align
value should have been used.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43legacy_status()
returns a value of 2 (B43legacy_STAT_STARTED); however, one finds that
the driver is unable to associate after resuming from hibernation unless
this routine returns 1. To satisfy both conditions, the routine is rewritten
to return TRUE whenever b43legacy_status() returns a value < 2.
This patch fixes the second problem listed in the postings for Red Hat
Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The routine b43_is_hw_radio_enabled() has long been a problem.
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43_status()
returns a value of 2 (B43_STAT_STARTED) (BUG 14181). Fixing that
results in Bug 14538 in which the driver is unable to reassociate
after resuming from hibernation because b43_status() returns 0.
The correct fix would be to determine why the status is 0; however,
I have not yet found why that happens. The correct value is found for
my device, which has PHY revision >= 3.
Returning TRUE when the PHY revision < 3 and b43_status() returns 0 fixes
the regression for 2.6.32.
This patch fixes the problem in Red Hat Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for ethtool selftest.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the NULL pointer dereference Oops in the ks8851 snl network
driver during transmission. All socket buffers from the queue are
processed inside the loop, but new workqueues have been scheduled to
run.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: Patrick Mullaney <pmullaney@novell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Replace magic values with constants
- Simplify length calculation and fix a bug
Based on valuable feedback from Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when disabling interrupts, driver was writing with IO, this is no
necessary because on ixgbe parts the hardware can "oneshot"
disable and clear the interrupt. So on 82598/82599 use of EIAM
should avoid one posted write per interrupt when in MSI-X mode.
This should improve performance and seems to in my limited
testing, reduce CPU utilization VERY slightly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drop variables that had cache lines modified in simultaneous hot paths.
keep some variables modified on hot paths but make their storage per queue.
cache align DMA data buffer start addresses.
cache align (padding) some structures that end within a cacheline.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
decrease the memory utilization of the tx / rx queue allocation
by changing the default ring size to 512 (from 1024). At
1024 rx entries of 2KB each (from 4kB slab) with 16 queues
ixgbe was using 64 MB of memory per port, which is not
necessary.
Users can still change queue lengths with ethtool -k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the Tx queue selection for FCoE traffic from ixgbe_xmit_frame()
and does it in the ndo_select_queue() call, moving all Tx queue selection
into a single routine.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the user priority for FCoE and use it directly for outgoing
FCoE traffic when DCB is enabled.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using remote wakeup and delayed transmission to allow
online device to go into usb autosuspend.
Minimal alternate support for devices that don't support
remote wakeup.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normal resume can do double duty as reset_resume() for this driver
as it keeps no state in the device
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ata_set_lba_range_entries used the variable max for two different things
which was confusing. Make the function take a buffer size in bytes as
argument and return the used buffer size upon completion.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Our current TRIM payload is a single sector that can accommodate 64 *
65535 blocks being unmapped. Report this value in the Block Limits
Maximum Unmap LBA count field.
If a storage device supports TRIM and the DRAT and RZAT bits are set,
report TPRZ=1 in Read Capacity(16).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove superfluous timings table entry while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MWDMA0 timings cannot be met with the PIIX based controller
programming interface.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
To help debug the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent race conditions with other reset events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.105.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3's firmware is no longer loaded from tg3_init_one(). Remove the
error path that releases the firmware back to the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver needs to use PCI configuration space to read the VPD data,
the accesses could collide with the pci_read_vpd() function. This patch
converts the driver to use pci_read_vpd() to avoid any potential
collisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the VPD code by creating preprocessor definitions
and using them in the place of hardcoded constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 57765 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 asic rev has MSI-X capability, but does not support TSS. This
patch changes the tx paths so that TSS is explicitly mentioned, rather
than implied through the ENABLE_MSIX flag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set correct bits to switch between UDMA2 and UDMA4.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix ->resume method to do chipset specific setup.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to mask out the port offset from the port number
cached in ld_qdi->timing.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dual port QDI6580 has shared PIO timings for master/slave
devices so it needs to use custom ->qc_issue method.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clear old MWDMA timings before programming new ones (IT8213
is a single port host so there is no need to check ap->port_no).
This change should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[ port of Sergei's fixes for pata_efar from commit 5f33b3b ]
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* do not clear PIO timings for master when programming slave
* program new PIO timings in the correct register nibble
Both changes should be safe as this is how we have been doing
things in IDE it8213 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Driver should program the cycle timing not the mode number
(doing the latter results in wrong timings being used).
There shouldn't be any problems with it as IDE it8213 host driver
has been doing it this way for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It has been dead for the last three years (== since the initial driver
merge) and probability that it will ever get fixed is quite low.
Since there is no reason to keep this dead code around any longer just
remove it (it can still be retrieved from the git history if necessary).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do not clear MWDMA timings for device on the other port when
programming slave device.
This change should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* do not clear PIO timings for master when programming slave
* do not clear PIO timings for device on the other port when
programming slave device
Both changes should be safe as this is how we have been doing
things in IDE slc90e66 host driver for years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix erroneous check for ap->udma_mask in do_pata_set_dmamode()
resulting in controller not being programmed properly for MWDMA.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a firmware command fails, only the failure codes are printed.
It is difficult to co-relate this to the actual command that has failed.
These changes will now print the command code that has failed.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ahci can drive the Promise PDC42819, but obviously it can only use SATA
disks connected to this controller. The controller can actually support
SAS disks as well, but we only know how to use it in it's AHCI mode.
Add a message to let users know that because ahci is driving their chip
they can only use the SATA disks connected to this controller.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
they weren't converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The comment in the driver actually describes HPT37x's timing register layout,
which is different from HPT36x. Fix it and reformat the comment, while at it.
Bump the driver version, accounting for several patches that forgot to do it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These drivers inherited from the older 'hpt366' IDE driver the buggy timing
register masks in their set_piomode() metods. As a result, too low command
cycle active time is programmed for slow PIO modes. Quite fortunately, it's
later "fixed up" by the set_dmamode() methods which also "helpfully" reprogram
the command timings, usually to PIO mode 4; unfortunately, setting an UltraDMA
mode #N also reprograms already set PIO data timings, usually to MWDMA mode #
max(N, 2) timings...
However, the drivers added some breakage of their own too: the bit that they
set/clear to control the FIFO is sometimes wrong -- it's actually the MSB of
the command cycle setup time; also, setting it in DMA mode is wrong as this
bit is only for PIO actually and clearing it for PIO modes is not needed as
no mode in any timing table has it set...
Fix all this, inverting the masks while at it, like in the 'hpt366' and
'pata_hpt366' drivers; bump the drivers' versions, accounting for recent
patches that forgot to do it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We were never able to get docs for this out of Toshiba for years. Dave
Barnes produced a NetBSD driver however and from that we can fill in the
needed tables.
As we correct the PCI identifiers a bit also update the old ide generic driver
at the same time so it stays compiling.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The auto sleep mode for btmrvl driver is not enabled by default.
This patch enables auto sleep mode when card is probed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The /dev/vhci ops don't refer to the module and so it is possible to
unload the module while the file descriptor is in use. This was an
accidental removal after the cleanup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After the removal of the module parameter for setting the minor number,
this variable became unused. So just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove the empty ioctl which just returns -EINVAL. vfs_ioctl() will
return -ENOTTY instead, but I doubt that any application will notice
the difference :)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
- no one is calling wb_writeback and write_cache_pages with
wbc.nonblocking=1 any more
- lumpy pageout will want to do nonblocking writeback without the
congestion wait
So remove the congestion checks as suggested by Chris.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Alex Elder <aelder@sgi.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Making the new stuff work broke some of the old chipsets. We need to go
back to the old set up values for these it seems. Unfortunately even with
documentation this is basically a mix of cargoculting and guesswork.
Chased down to the exact line by Gianluca.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Daniela Engert pointed out that there are some implementation notes for the
643 and 646 that deal with certain serialization rules. In theory we don't
need them because they apply when the motherboard decides not to retry PCI
requests for long enough and the chip is busy doing a DMA transfer on the
other channel.
The rule basically is "don't touch the taskfile of the other channel while
a DMA is in progress". To implement that we need to
- not issue a command on a channel when there is a DMA command queued
- not issue a DMA command on a channel when there are PIO commands queued
- use the alternative access to the interrupt source so that we do not
touch altstatus or status on shared IRQ.
Updated to remote extra conditional check Bartlomiej noted and to remove
the variables for irq checks as the CMD648 doesn't have the underlying problem.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bartlomiej pointed out that while this got fixed in the old driver whoever
did it didn't port it across.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reported by Mikulas Patocka.
VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for the ATA TRIM command in libata. We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.
Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.
However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.
This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination. Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode. This was reported in the following bugzilla bug.
http://bugzilla.kernel.org/show_bug.cgi?id=14543
This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.
Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The detection was reversed between primary and secondary ports.
Fix it to match hpt366 and the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.
It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.
PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.
Do pci_dev_put only once.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Missing _SDD is not an error. Don't treat it as one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix dma-api-checking warnings in Sun HME
Sun HME driver is mapping the first fragment with dma_map_single and subsequent
fragments with dma_map_page. It is unmapping all fragments with dma_unmap_single
and that produces the warning.
This patch changes it so that it unmaps only the first fragment with
dma_unmap_single and subsequent fragments are unmapped with dma_unmap_page.
WARNING: at lib/dma-debug.c:816 check_unmap+0x3ac/0x780()
hme 0000:01:01.1: DMA-API: device driver frees DMA memory with wrong function [device address=0x00000000c1082000] [size=32 bytes] [mapped as page] [unmapped as single]
Modules linked in: nbd sunhme openpromfs sermouse unix
Call Trace:
[0000000000456910] warn_slowpath_common+0x50/0xa0
[0000000000571f4c] check_unmap+0x3ac/0x780
[0000000000572570] debug_dma_unmap_page+0x50/0x60
[000000001002f5fc] happy_meal_tx+0x11c/0x260 [sunhme]
[000000001002fc4c] happy_meal_interrupt+0xcc/0xe0 [sunhme]
[0000000000492d94] handle_fasteoi_irq+0x74/0x100
[000000000042ac0c] handler_irq+0xcc/0x100
[0000000000426a54] valid_addr_bitmap_patch+0x14/0x1c0
[0000000000665de0] _spin_unlock_irqrestore+0x40/0x60
[0000000000462bb8] mod_timer+0x118/0x1a0
[00000000005ec254] sk_reset_timer+0x14/0x40
[0000000000635e4c] tcp_event_new_data_sent+0x8c/0xc0
[0000000000639374] __tcp_push_pending_frames+0x34/0xc0
---[ end trace 73d5c42c1e9f11c4 ]---
Mapped at:
[<000000001002f148>] happy_meal_start_xmit+0x308/0x480 [sunhme]
[<00000000005fc858>] dev_hard_start_xmit+0x318/0x3c0
[<000000000060fec4>] sch_direct_xmit+0x1a4/0x200
[<00000000005fced0>] dev_queue_xmit+0x410/0x560
[<0000000000604a1c>] neigh_resolve_output+0xfc/0x300
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unimplemented operations should not silently fail.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions provide the default behaviour and do not need to be
set in struct ethtool_ops.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace pci_alloc_consistent() with dma_alloc_coherent() so that
appropriate GFP flags can be used.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old code mistakenly zeroed out the upper 32-bit of the DMA address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix code to read the proper iSCSI MAC address for bnx2x devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to send a HALT command to the firmware to fully shutdown the bnx2x
rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old code was initializing the ring producers using an incorrect I/O
address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle few corner cases in firmware hang detection and recovery:
o Don't mark device state as READY, till handshake with
firmware is done.
o During probe, if start_firmware fails, restore reference
count.
o Don't increment refernce count, if start_firmware fails
during firmware reset.
o Clear __NX_RESETTING bit, incase of fatal error or tempeature
reaches critical limit so that pci remove() doesn't poll on
this bit.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver maps only some part of the MMIO bar 0 in case of
NX2031. This is sufficient for tx and rx by the driver.
When debug tools need to access resources in
unmapped regions, driver needs to map these on the fly
in order to complete read/write request.
Signed-off-by: Narender Kumar <narender.kumar@qlogic.com>
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some function pointers for a few PHY operations (for 82578 and 82567) and
were set incorrectly causing functions to be executed that were accessing
incorrect PHY register offsets for that particular device. This patch also
moves a few PHY-specific functions from ich8lan.c to the more appropriate
phy.c.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround that detects the correct PHY ID when an initial read of the
PHY ID registers returns an invalid one should retry up to ten times with
a small delay between attempts using a single PHY address and then repeat
using the remaining possible PHY addresses. Do this instead of trying each
possible PHY address repeating that up to 100 times.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function pointers for 8257x devices are not set. This is not really a
problem now because there is nothing in the driver that references the
pointers for this particular MAC-family (the appropriate functions are
called directly), but the pointers should be set in case they are used in
the future.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the skb_dma_map/unmap calls from the igbvf driver due to
the fact that it does not play well with HW IOMMU when combined with
transmitting cloned skbs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes skb_dma_map/unmap calls from the igb driver due to the
fact that the call is incompatible with iommu enabled kernels. In order to
prevent warnings about using the wrong unmap call I have added a
mapped_as_page value to the buffer_info structure to track if the mapped
region is a page or a buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes skb_dma_map/unmap calls from the ixgbe driver due to the
fact that the calls don't work with HW IOMMU enabled systems. The problem
is that multiple mappings will give different results when HW IOMMU is
enabled and the skb_dma_map/unmap calls only have one location to store
mappings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_map is incompatible with HW iommu due to the fact that multiple
mappings can result in different results each time. For this reason it is
best to just remove use of these function calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the use of skb_dma_map from the e1000 driver in order to avoid
issues when HW iommu are in use.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing we have found that skb_dma_map/unmap is incompatible with HW
IOMMU due to the fact that multiple mappings will return different results.
In order to correct this we need to remove skb_dma_map/unmap calls from the
e1000e driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
request_region should be used with release_region, not request_mem_region.
Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c,
the problem is actually the other way around; request_mem_region should be
used instead of request_region.
The semantic patch that finds/fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r1@
expression start;
@@
request_region(start,...)
@b1@
expression r1.start;
@@
request_mem_region(start,...)
@depends on !b1@
expression r1.start;
expression E;
@@
- release_mem_region
+ release_region
(start,E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These laptops often leave i8042 in a wierd state resulting in non-
operational touchpad and keyboard.
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bnx2 is failing when a PCI error is detected. The error is the
following:
bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d
This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2ba ("PCI: Clear
saved_state after the state has been restored").
Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version that made it into mainline missed the initialisation of the
chip handle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch fixes the compilation failure of
rc32434 due to a bad module parameter description.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The size value passed to ioremap_nocache() is not correct.
Use resource_size() to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Changed braces position on some statements.
Inserted a space between an "if" keyword and a parenthesis.
Signed-off-by: Rudy Matela <rudy.matela@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A small cleanup after last net-2.6 merge into net-next-2.6
As we are going to free skb, no need to set skb->skb_iif or skb->dev
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool_ops.set_settings support to the PS3 gelic network driver.
Allows manual setting of ethernet link speed.
Signed-off-by: Hideyuki Sasaki <xhide@rd.scei.sony.co.jp>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup of the gelic driver enumerations:
o Add some missing commas.
o Add an Ether port post fix (PS3 currently only supports PORT_0).
o Add a new enum gelic_lv1_phy to use when interacting with the PHY.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time while doing ethtool->get_settings we are accessing
the hardware to get link status and port information.
This is not necessary. We now use the cached copy for this info
and update it when the link status changes.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add be_rx_polls to count number of times NAPI called rx poll function.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port identification/beaconing is failing if device open has not been done.
Fixing it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow only valid ether addresses to be assigned and used for the interface.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
patch to initialize netdev->vlan_features appropriately.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For hardware limit to support TSOV6, just disable this feature
Signed-off-by: Jie Yang <jie.yang@atheros.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use the sizeof the pointer to clear the result
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the case for 82577 because it does not support the ability to check
for downshift. Add case for e1000_phy_bm which can do this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some helpful debug messages.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new PCI device ID is for a new combination of MAC and PHY both of
which already have supporting code in the driver, just not yet in this
combination. During validation of the device, an intermittent issue was
discovered with waking it from a suspended state which can be resolved with
the pre-existing workaround to disable gigabit speed prior to suspending.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt