The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix sparse warning:
drivers/gpio/gpiolib-of.c:35:5: warning:
symbol 'of_gpio_spi_cs_get_count' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191130012828.14504-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a special quirk to handle the Freescale
nonstandard SPI chipselect GPIOs in the gpiolib-of.c
file, but it currently only handles the case where
the GPIOs are actually requested (gpiod_*get()).
We also need to handle that the SPI core attempts
to count the GPIOs before use, and that needs a
similar quirk in the OF part of the library.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reverts commit 6e0a32d6f3 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd876 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407f ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the STM32 QSPI binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191120194444.10540-1-benjamin.gaignard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no reason to use the dma_request_slave_channel_compat() as no
filter function and parameter is provided.
Switch the driver to use dma_request_chan() instead and add support for
deferred probing against DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191121092703.30465-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133916.13595-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit d948e6ca18 ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.
This causes SPI devices to return errors for cases where they do:
ret = spi_setup(spi);
if (ret)
return ret;
As in many cases the SPI devices do not check for if (ret < 0).
Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.
Fixes: d948e6ca18 ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to
Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Devices with chip selects driven via GPIO are not compatible with the
spi-mem operations. Fallback to using standard spi transfers when the
device is connected with a gpio CS.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.
As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.
We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.
Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Committed version of the commit b9fc2d207e ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.
Complete the code move by doing those changes now.
Fixes: b9fc2d207e ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.
Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The current conditional for PCI ID matching is hard to read.
Introduce couple of temporary variables to increase readability
of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This core supports either 8, 16 or 32 bits as word width. This value is only
settable on instantiation, and thus we need to support any of them by means
of the device tree.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-3-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This property is used to set the number of bits per transfer (bits_per_word).
Xilinx' IP core allows either 8, 16 or 32, and is non changeable on runtime,
only when instantiating the core.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-2-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe Leroy