Now that bitmaps can be resized, we can allow an array to be resized
while the bitmap is present.
This only covers resizing that involves changing the effective size
of member devices, not resizing that changes the number of devices.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to fix a read error, it is acceptable to read from a
device that is recovering, provided the recovery has got past the
place we are reading from. This makes the test for "can we read from
here" the same as the test in read_balance.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping we can avoid costly intermediate backup by
changing the 'start' address of the array on the device
(if there is enough room).
So as a first step, allow such a change to be requested
through sysfs, and recorded in v1.x metadata.
(As we didn't previous check that all 'pad' fields were zero,
we need a new FEATURE flag for this.
A (belatedly) check that all remaining 'pad' fields are
zero to avoid a repeat of this)
The new data offset must be requested separately for each device.
This allows each to have a different change in the data offset.
This is not likely to be used often but as data_offset can be
set per-device, new_data_offset should be too.
This patch also removes the 'acknowledged' arg to rdev_set_badblocks as
it is never used and never will be. At the same time we add a new
arg ('in_new') which is currently always zero but will be used more
soon.
When a reshape finishes we will need to update the data_offset
and rdev->sectors. So provide an exported function to do that.
Signed-off-by: NeilBrown <neilb@suse.de>
If r1bio->sectors % 8 != 0,then the memcmp and a later
memcpy will omit the last bio_vec.
This is suitable for any stable kernel since 3.1 when bad-block
management was introduced.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When comparing two pages read from different legs of a mirror, only
compare the bytes that were read, not the whole page.
In most cases we read a whole page, but in some cases with
bad blocks or odd sizes devices we might read fewer than that.
This bug has been present "forever" but at worst it might cause
a report of two many mismatches and generate a little bit
extra resync IO, so there is no need to back-port to -stable
kernels.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Because rde->nr_pending > 0,so can not remove this disk.
And in any case, we aren't holding rcu_read_lock()
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently we don't honour merge_bvec_fn in member devices so if there
is one, we force all requests to be single-page at most.
This is not ideal.
So create a raid1 merge_bvec_fn to check that function in children
as well.
This introduces a small problem. There is no locking around calls
the ->merge_bvec_fn and subsequent calls to ->make_request. So a
device added between these could end up getting a request which
violates its merge_bvec_fn.
Currently the best we can do is synchronize_sched(). This will work
providing no preemption happens. If there is is preemption, we just
have to hope that new devices are largely consistent with old devices.
Signed-off-by: NeilBrown <neilb@suse.de>
md.h has an 'rdev_for_each()' macro for iterating the rdevs in an
mddev. However it uses the 'safe' version of list_for_each_entry,
and so requires the extra variable, but doesn't include 'safe' in the
name, which is useful documentation.
Consequently some places use this safe version without needing it, and
many use an explicity list_for_each entry.
So:
- rename rdev_for_each to rdev_for_each_safe
- create a new rdev_for_each which uses the plain
list_for_each_entry,
- use the 'safe' version only where needed, and convert all other
list_for_each_entry calls to use rdev_for_each.
Signed-off-by: NeilBrown <neilb@suse.de>
If RAID1 or RAID10 is used under LVM or some other stacking
block device, it is possible to enter a deadlock during
resync or recovery.
This can happen if the upper level block device creates
two requests to the RAID1 or RAID10. The first request gets
processed, blocks recovery and queue requests for underlying
requests in current->bio_list. A resync request then starts
which will wait for those requests and block new IO.
But then the second request to the RAID1/10 will be attempted
and it cannot progress until the resync request completes,
which cannot progress until the underlying device requests complete,
which are on a queue behind that second request.
So allow that second request to proceed even though there is
a resync request about to start.
This is suitable for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Ray Morris <support@bettercgi.com>
Tested-by: Ray Morris <support@bettercgi.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since we added 'replacement' capability, RAID1 can have twice
as many devices as ->raid_disks indicates.
So md_raid1_congested needs to check that many possible devices,
not just ->raid_disks many.
Signed-off-by: NeilBrown <neilb@suse.de>
We normally try to avoid reading from write-mostly devices, but when
we do we really have to check for bad blocks and be sure not to
try reading them.
With the current code, best_good_sectors might not get set and that
causes zero-length read requests to be send down which is very
confusing.
This bug was introduced in commit d2eb35acfd and so the patch
is suitable for 3.1.x and 3.2.x
Reported-and-tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reported-and-tested-by: Art -kwaak- van Breemen <ard@telegraafnet.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org
Now that WantReplacement drives are replaced cleanly, mark a drive
as want_replacement when we see a write error. It might get failed soon so
the WantReplacement flag is irrelevant, but if the write error is recorded
in the bad block log, we still want to activate any spare that might
be available.
Signed-off-by: NeilBrown <neilb@suse.de>
When attempting to add a spare to a RAID1 array, also consider
adding it as a replacement for a want_replacement device.
Signed-off-by: NeilBrown <neilb@suse.de>
If a Replacement is seen, file it as such.
If we see two replacements (or two normal devices) for the one slot,
abort.
Signed-off-by: NeilBrown <neilb@suse.de>
When recovery completes ->spare_active is called.
This checks if the replacement is ready and if so it fails
the original.
Signed-off-by: NeilBrown <neilb@suse.de>
In RAID1, a replacement is much like a normal device, so we just
double the size of the relevant arrays and look at all possible
devices for reads and writes.
This means that the array looks like it is now double the size in some
way - we need to be careful about that.
In particular, we checking if the array is still degraded while
creating a recovery request we need to only consider the first 'half'
- i.e. the real (non-replacement) devices.
Signed-off-by: NeilBrown <neilb@suse.de>
In general mddev->raid_disks can change unexpectedly while
conf->raid_disks will only change in a very controlled way. So change
some uses of one to the other.
The use of mddev->raid_disks will not cause actually problems but
this way is more consistent and safer in the long term.
Signed-off-by: NeilBrown <neilb@suse.de>
Soon an array will be able to have multiple devices with the
same raid_disk number (an original and a replacement). So removing
a device based on the number won't work. So pass the actual device
handle instead.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
A pending cleanup will mean that module.h won't be implicitly
everywhere anymore. Make sure the modular drivers in md dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
In 3.0 we changed the way recovery_disabled was handle so that instead
of testing against zero, we test an mddev-> value against a conf->
value.
Two problems:
1/ one place in raid1 was missed and still sets to '1'.
2/ We didn't explicitly set the conf-> value at array creation
time.
It defaulted to '0' just like the mddev value does so they
could appear equal and thus disable recovery.
This did not affect normal 'md' as it calls bind_rdev_to_array
which changes the mddev value. However the dmraid interface
doesn't call this and so doesn't change ->recovery_disabled; so at
array start all recovery is incorrectly disabled.
So initialise the 'conf' value to one less that the mddev value, so
the will only be the same when explicitly set that way.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
bio originally has the functionality to set the complete cpu, but
it is broken.
Chirstoph said that "This code is unused, and from the all the
discussions lately pretty obviously broken. The only thing keeping
it serves is creating more confusion and possibly more bugs."
And Jens replied with "We can kill bio_set_completion_cpu(). I'm fine
with leaving cpu control to the request based drivers, they are the
only ones that can toggle the setting anyway".
So this patch tries to remove all the work of controling complete cpu
from a bio.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
RAID1 and RAID10 handle write requests by queuing them for handling by
a separate thread. This is because when a write-intent-bitmap is
active we might need to update the bitmap first, so it is good to
queue a lot of writes, then do one big bitmap update for them all.
However writeback request devices to appear to be congested after a
while so it can make some guesstimate of throughput. The infinite
queue defeats that (note that RAID5 has already has a finite queue so
it doesn't suffer from this problem).
So impose a limit on the number of pending write requests. By default
it is 1024 which seems to be generally suitable. Make it configurable
via module option just in case someone finds a regression.
Signed-off-by: NeilBrown <neilb@suse.de>
The typedefs are just annoying. 'mdk' probably refers to 'md_k.h'
which used to be an include file that defined this thing.
Signed-off-by: NeilBrown <neilb@suse.de>
When normal-write and sync-read/write bio completes, we should
find out the disk number the bio belongs to. Factor those common
code out to a separate function.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Two related problems:
1/ some error paths call "md_unregister_thread(mddev->thread)"
without subsequently clearing ->thread. A subsequent call
to mddev_unlock will try to wake the thread, and crash.
2/ Most calls to md_wakeup_thread are protected against the thread
disappeared either by:
- holding the ->mutex
- having an active request, so something else must be keeping
the array active.
However mddev_unlock calls md_wakeup_thread after dropping the
mutex and without any certainty of an active request, so the
->thread could theoretically disappear.
So we need a spinlock to provide some protections.
So change md_unregister_thread to take a pointer to the thread
pointer, and ensure that it always does the required locking, and
clears the pointer properly.
Reported-by: "Moshe Melnikov" <moshe@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
cc: stable@kernel.org
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.
To detect if we need to submit another write request we test:
if (sectors_handled < (bio->bi_size >> 9)) {
However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.
So move the **_write_done call until after the test against
bio->bi_size.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862
Reported-by: Bruno Wolff III <bruno@wolff.to>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: NeilBrown <neilb@suse.de>
raid1d is too big with several deep branches.
So separate them out into their own functions.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we cannot read a block from anywhere during recovery, there is
now a better approach than just giving up.
We can record a bad block on each device and keep going - being
careful not to clear the bad block when a write succeeds as it might -
it will be a write of incorrect data.
We have now reached the state where - for raid1 - we only call
md_error if md_set_badblocks has failed.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we find a bad block while writing as part of resync/recovery we
need to report that back to raid1d which must record the bad block,
or fail the device.
Similarly when fixing a read error, a further error should just
record a bad block if possible rather than failing the device.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
When we get a write error (in the data area, not in metadata),
update the badblock log rather than failing the whole device.
As the write may well be many blocks, we trying writing each
block individually and only log the ones which fail.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
When performing write-behind we allocate pages to store the data
during write.
Previously we just keep a list of pages. Now we keep a list of
bi_vec which includes offset and size.
This means that the r1bio has complete information to create a new
bio which will be needed for retrying after write errors.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we succeed in writing to a block that was recorded as
being bad, we clear the bad-block record.
This requires some delayed handling as the bad-block-list update has
to happen in process-context.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If we have seen any write error on a drive, then don't write to
any known-bad blocks on that drive.
If necessary, we divide the write request up into pieces just
like we do for reads, so each piece is either all written or
all not written to any given drive.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
It is only safe to choose not to write to a bad block if that bad
block is safely recorded in metadata - i.e. if it has been
'acknowledged'.
If it hasn't we need to wait for the acknowledgement.
We support that using rdev->blocked wait and
md_wait_for_blocked_rdev by introducing a new device flag
'BlockedBadBlock'.
This flag is only advisory.
It is cleared whenever we acknowledge a bad block, so that a waiter
can re-check the particular bad blocks that it is interested it.
It should be set by a caller when they find they need to wait.
This (set after test) is inherently racy, but as
md_wait_for_blocked_rdev already has a timeout, losing the race will
have minimal impact.
When we clear "Blocked" was also clear "BlockedBadBlocks" incase it
was set incorrectly (see above race).
We also modify the way we manage 'Blocked' to fit better with the new
handling of 'BlockedBadBlocks' and to make it consistent between
externally managed and internally managed metadata. This requires
that each raidXd loop checks if the metadata needs to be written and
triggers a write (md_check_recovery) if needed. Otherwise a queued
write request might cause raidXd to wait for the metadata to write,
and only that thread can write it.
Before writing metadata, we set FaultRecorded for all devices that
are Faulty, then after writing the metadata we clear Blocked for any
device for which the Fault was certainly Recorded.
The 'faulty' device flag now appears in sysfs if the device is faulty
*or* it has unacknowledged bad blocks. So user-space which does not
understand bad blocks can continue to function correctly.
User space which does, should not assume a device is faulty until it
sees the 'faulty' flag, and then sees the list of unacknowledged bad
blocks is empty.
Signed-off-by: NeilBrown <neilb@suse.de>
When performing resync/etc, keep the size of the request
small enough that it doesn't overlap any known bad blocks.
Devices with badblocks at the start of the request are completely
excluded.
If there is nowhere to read from due to bad blocks, record
a bad block on each target device.
Now that we never read from known-bad-blocks we can allow devices with
known-bad-blocks into a RAID1.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that we have a bad block list, we should not read from those
blocks.
There are several main parts to this:
1/ read_balance needs to check for bad blocks, and return not only
the chosen device, but also how many good blocks are available
there.
2/ fix_read_error needs to avoid trying to read from bad blocks.
3/ read submission must be ready to issue multiple reads to
different devices as different bad blocks on different devices
could mean that a single large read cannot be served by any one
device, but can still be served by the array.
This requires keeping count of the number of outstanding requests
per bio. This count is stored in 'bi_phys_segments'
4/ retrying a read needs to also be ready to submit a smaller read
and queue another request for the rest.
This does not yet handle bad blocks when reading to perform resync,
recovery, or check.
'md_trim_bio' will also be used for RAID10, so put it in md.c and
export it.
Signed-off-by: NeilBrown <neilb@suse.de>
As no personality understand bad block lists yet, we must
reject any device that is known to contain bad blocks.
As the personalities get taught, these tests can be removed.
This only applies to raid1/raid5/raid10.
For linear/raid0/multipath/faulty the whole concept of bad blocks
doesn't mean anything so there is no point adding the checks.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
If device-mapper creates a RAID1 array that includes devices to
be rebuilt, it will deref a NULL pointer when finished because
sysfs is not used by device-mapper instantiated RAID devices.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Read errors are considered to corrected if write-back and re-read
cycle is finished without further problems. Thus moving the rdev->
corrected_errors counting after the re-reading looks more reasonable
IMHO. Also included a couple of whitespace fixes on sync_page_io().
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If we hit a read error while recovering a mirror, we want to abort the
recovery without necessarily failing the disk - as having a disk this
a read error is better than not having an array at all.
Currently this is managed with a per-array flag "recovery_disabled"
and is only implemented for RAID1. For RAID10 we will need finer
grained control as we might want to disable recovery for individual
devices separately.
So push more of the decision making into the personality.
'recovery_disabled' is now a 'cookie' which is copied when the
personality want to disable recovery and is changed when a device is
added to the array as this is used as a trigger to 'try recovery
again'.
This will allow RAID10 to get the control that it needs.
Signed-off-by: NeilBrown <neilb@suse.de>
There are places where sysfs links to rdev are handled
in a same way. Add the helper functions to consolidate
them.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
As per printk_ratelimit comment, it should not be used.
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Changes to allow RAID1 to be used by device-mapper (dm-raid.c)
Added the necessary congestion function and conditionalize calls requiring an
array 'queue' or 'gendisk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The sysfs attribute 'resync_start' (known internally as recovery_cp),
records where a resync is up to. A value of 0 means the array is
not known to be in-sync at all. A value of MaxSector means the array
is believed to be fully in-sync.
When the size of member devices of an array (RAID1,RAID4/5/6) is
increased, the array can be increased to match. This process sets
resync_start to the old end-of-device offset so that the new part of
the array gets resynced.
However with RAID1 (and RAID6) a resync is not technically necessary
and may be undesirable. So it would be good if the implied resync
after the array is resized could be avoided.
So: change 'resync_start' so the value can be changed while the array
is active, and as a precaution only allow it to be changed while
resync/recovery is 'frozen'. Changing it once resync has started is
not going to be useful anyway.
This allows the array to be resized without a resync by:
write 'frozen' to 'sync_action'
write new size to 'component_size' (this will set resync_start)
write 'none' to 'resync_start'
write 'idle' to 'sync_action'.
Also slightly improve some tests on recovery_cp when resizing
raid1/raid5. Now that an arbitrary value could be set we should be
more careful in our tests.
Signed-off-by: NeilBrown <neilb@suse.de>
The current handling and freeing of these pages is a bit fragile.
We only keep the list of allocated pages in each bio, so we need to
still have a valid bio when freeing the pages, which is a bit clumsy.
So simply store the allocated page list in the r1_bio so it can easily
be found and freed when we are finished with the r1_bio.
Signed-off-by: NeilBrown <neilb@suse.de>
If we get a read error during resync/recovery we current repeat with
single-page reads to find out just where the error is, and possibly
read each page from a different device.
With check/repair we don't currently do that, we just fail.
However it is possible that while all devices fail on the large 64K
read, we might be able to satisfy each 4K from one device or another.
So call fix_sync_read_error before process_checks to maximise the
chance of finding good data and writing it out to the devices with
read errors.
For this to work, we need to set the 'uptodate' flags properly after
fix_sync_read_error has succeeded.
Signed-off-by: NeilBrown <neilb@suse.de>
These changes are mostly cosmetic:
1/ change mddev->raid_disks to conf->raid_disks because the later is
technically safer, though in current practice it doesn't matter in
this particular context.
2/ Rearrange two for / if loops to have an early 'continue' so the
body of the 'if' doesn't need to be indented so much.
Signed-off-by: NeilBrown <neilb@suse.de>
sync_request_write is too big and too deep.
So split out two self-contains bits of functionality into separate
function.
Signed-off-by: NeilBrown <neilb@suse.de>
read_balance has two loops which both look for a 'best'
device based on slightly different criteria.
This is clumsy and makes is hard to add extra criteria.
So replace it all with a single loop that combines everything.
Signed-off-by: NeilBrown <neilb@suse.de>
We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.
Also remove some plug-related code that is no longer needed.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid submits a lot of IO from the various raid threads.
So adding start/finish plug calls to those so that some
plugging happens.
Signed-off-by: NeilBrown <neilb@suse.de>
MD and DM create a new bio_set for every metadevice. Each bio_set has an
integrity mempool attached regardless of whether the metadevice is
capable of passing integrity metadata. This is a waste of memory.
Instead we defer the allocation decision to MD and DM since we know at
metadevice creation time whether integrity passthrough is needed or not.
Automatic integrity mempool allocation can then be removed from
bioset_create() and we make an explicit integrity allocation for the
fs_bio_set.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Acked-by: Mike Snitzer <snizer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
blk_throtl_exit assumes that ->queue_lock still exists,
so make sure that it does.
To do this, we stop redirecting ->queue_lock to conf->device_lock
and leave it pointing where it is initialised - __queue_lock.
As the blk_plug functions check the ->queue_lock is held, we now
take that spin_lock explicitly around the plug functions. We don't
need the locking, just the warning removal.
This is needed for any kernel with the blk_throtl code, which is
which is 2.6.37 and later.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Add new parameter to 'sync_page_io'.
The new parameter allows us to distinguish between metadata and data
operations. This becomes important later when we add the ability to
use separate devices for data and metadata.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Commit 4044ba58dd supposedly fixed a
problem where if a raid1 with just one good device gets a read-error
during recovery, the recovery would abort and immediately restart in
an infinite loop.
However it depended on raid1_remove_disk removing the spare device
from the array. But that does not happen in this case. So add a test
so that in the 'recovery_disabled' case, the device will be removed.
This suitable for any kernel since 2.6.29 which is when
recovery_disabled was introduced.
Cc: stable@kernel.org
Reported-by: Sebastian Färber <faerber@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The code for searching through the device list to read-balance in
raid1 is rather clumsy and hard to follow. Try to simplify it a bit.
No important functionality change here.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_clone and bio_alloc allocate from a common bio pool.
If an md device is stacked with other devices that use this pool, or under
something like swap which uses the pool, then the multiple calls on
the pool can cause deadlocks.
So allocate a local bio pool for each md array and use that rather
than the common pool.
This pool is used both for regular IO and metadata updates.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently sync_page_io takes a 'bdev'.
Every caller passes 'rdev->bdev'.
We will soon want another field out of the rdev in sync_page_io,
So just pass the rdev instead of the bdev out of it.
Signed-off-by: NeilBrown <neilb@suse.de>
Though this mem alloc is GFP_NOIO an so will not deadlock, it seems
better to do the allocation before 'raise_barrier' which stops any IO
requests while the resync proceeds.
raid10 always uses this order, so it is at least consistent to do the
same in raid1.
Signed-off-by: NeilBrown <neilb@suse.de>
bio_alloc can never fail (as it uses a mempool) but an block
indefinitely, especially if the caller is holding a reference to a
previously allocated bio.
So these to places which both handle failure and hold multiple bios
should not use bio_alloc, they should use bio_kmalloc.
Signed-off-by: NeilBrown <neilb@suse.de>
It is not safe to allocate from a mempool while holding an item
previously allocated from that mempool as that can deadlock when the
mempool is close to exhaustion.
So don't use a bio list to collect the bios to write to multiple
devices in raid1 and raid10.
Instead queue each bio as it becomes available so an unplug will
activate all previously allocated bios and so a new bio has a chance
of being allocated.
This means we must set the 'remaining' count to '1' before submitting
any requests, then when all are submitted, decrement 'remaining' and
possible handle the write completion at that point.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_get_counter returns the number of sectors covered
by the counter in a pass-by-reference variable.
In some cases this can be very large, so make it a sector_t
for safety.
Signed-off-by: NeilBrown <neilb@suse.de>
When performing a resync we pre-allocate some bios and repeatedly use
them. This requires us to re-initialise them each time.
One field (bi_comp_cpu) and some flags weren't being initiaised
reliably.
Signed-off-by: NeilBrown <neilb@suse.de>
bitmap_start_sync returns - via a pass-by-reference variable - the
number of sectors before we need to check with the bitmap again.
Since commit ef42567335 this number can be substantially larger,
2^27 is a common value.
Unfortunately it is an 'int' and so when raid1.c:sync_request shifts
it 9 places to the left it becomes 0. This results in a zero-length
read which the scsi layer justifiably complains about.
This patch just removes the shift so the common case becomes safe with
a trivially-correct patch.
In the next merge window we will convert this 'int' to a 'sector_t'
Reported-by: "George Spelvin" <linux@horizon.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch converts md to support REQ_FLUSH/FUA instead of now
deprecated REQ_HARDBARRIER. In the core part (md.c), the following
changes are notable.
* Unlike REQ_HARDBARRIER, REQ_FLUSH/FUA don't interfere with
processing of other requests and thus there is no reason to mark the
queue congested while FLUSH/FUA is in progress.
* REQ_FLUSH/FUA failures are final and its users don't need retry
logic. Retry logic is removed.
* Preflush needs to be issued to all member devices but FUA writes can
be handled the same way as other writes - their processing can be
deferred to request_queue of member devices. md_barrier_request()
is renamed to md_flush_request() and simplified accordingly.
For linear, raid0 and multipath, the core changes are enough. raid1,
5 and 10 need the following conversions.
* raid1: Handling of FLUSH/FUA bio's can simply be deferred to
request_queues of member devices. Barrier related logic removed.
* raid5: Queue draining logic dropped. FUA bit is propagated through
biodrain and stripe resconstruction such that all the updated parts
of the stripe are written out with FUA writes if any of the dirtying
writes was FUA. preread_active_stripes handling in make_request()
is updated as suggested by Neil Brown.
* raid10: FUA bit needs to be propagated to write clones.
linear, raid0, 1, 5 and 10 tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
commit 7b6d91daee changed the behaviour
of a few variables in raid1 and raid10 from flags to bit-sets, but
left them as type 'bool' so they did not work.
Change them (back) to unsigned long.
(historical note: see 1ef04fefe2)
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jiri Slaby <jslaby@suse.cz> and many others
md_check_recovery expects ->spare_active to return 'true' if any
spares were activated, but none of them do, so the consequent change
in 'degraded' is not notified through sysfs.
So count the number of spares activated, subtract it from 'degraded'
just once, and return it.
Reported-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When RAID1 is done syncing disks, it'll update the state
of synced rdevs to In_sync. But it neglected to notify
sysfs that the attribute changed. So any programs that
are waiting for an rdev's state to change will not be
woken.
(raid5/raid10 added by neilb)
Signed-off-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Conflicts:
drivers/md/md.c
- Resolved conflict in md_update_sb
- Added extra 'NULL' arg to new instance of sysfs_get_dirent.
Signed-off-by: NeilBrown <neilb@suse.de>
read_balance uses a "unsigned long" for a sector number which
will get truncated beyond 2TB.
This will cause read-balancing to be non-optimal, and can cause
data to be read from the 'wrong' branch during a resync. This has a
very small chance of returning wrong data.
Reported-by: Jordan Russell <jr-list-2010@quo.to>
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a raid1 array is configured to support write-behind
on some devices, it normally only reads from other devices.
If all devices are write-behind (because the rest have failed)
it is possible for a read request to be serviced before a
behind-write request, which would appear as data corruption.
So when forced to read from a WriteMostly device, wait for any
write-behind to complete, and don't start any more behind-writes.
Signed-off-by: NeilBrown <neilb@suse.de>
This message seems to suggest the named device is the one on which a
read failed, however it is actually the device that the read will be
redirected to.
So make the message a little clearer.
Reported-by: Tim Burgess <ozburgess@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We used to pass the personality make_request function direct
to the block layer so the first argument had to be a queue.
But now we have the intermediary md_make_request so it makes
at lot more sense to pass a struct mddev_s.
It makes it possible to have an mddev without its own queue too.
Signed-off-by: NeilBrown <neilb@suse.de>
We set ->changed to 1 and call check_disk_change at the end
of md_open so that bd_invalidated would be set and thus
partition rescan would happen appropriately.
Now that we call revalidate_disk directly, which sets bd_invalidates,
that indirection is no longer needed and can be removed.
Signed-off-by: NeilBrown <neilb@suse.de>
While I generally prefer letting personalities do as much as possible,
given that we have a central md_make_request anyway we may as well use
it to simplify code.
Also this centralises knowledge of ->gendisk which will help later.
Signed-off-by: NeilBrown <neilb@suse.de>
void pointers do not need to be cast to other pointer types.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There is a very small race window when writing to a
RAID1 such that if a device is marked faulty at exactly the wrong
time, the write-in-progress will not be sent to the device,
but the bitmap (if present) will be updated to say that
the write was sent.
Then if the device turned out to still be usable as was re-added
to the array, the bitmap-based-resync would skip resyncing that
block, possibly leading to corruption. This would only be a problem
if no further writes were issued to that area of the device (i.e.
that bitmap chunk).
Suitable for any pending -stable kernel.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
If a component device has a merge_bvec_fn then as we never call it
we must ensure we never need to. Currently this is done by setting
max_sector to 1 PAGE, however this does not stop a bio being created
with several sub-page iovecs that would violate the merge_bvec_fn.
So instead set max_segments to 1 and set the segment boundary to the
same as a page boundary to ensure there is only ever one single-page
segment of IO requested at a time.
This can particularly be an issue when 'xen' is used as it is
known to submit multiple small buffers in a single bio.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
... and into bitmap_info. These are all configuration parameters
that need to be set before the bitmap is created.
Signed-off-by: NeilBrown <neilb@suse.de>
This will allow us to stop writeout to portions of the array
while they are resynced by someone else - e.g. another node in
a cluster.
Signed-off-by: NeilBrown <neilb@suse.de>
commit 4706b349f was a forward port of a fix that was needed
for SLES10. But in fact it is not needed in mainline because
the earlier commit dd00a99e7a fixes the same problem in a
better way.
Further, this commit introduces a bug in the way it interacts with
the automatic read-error-correction. If, after a read error is
successfully corrected, the same disk is chosen to re-read - the
re-read won't be attempted but an error will be returned instead.
After reverting that commit, there is the possibility that a
read error on a read-only array (where read errors cannot
be corrected as that requires a write) will repeatedly read the same
device and continue to get an error.
So in the "Array is readonly" case, fail the drive immediately on
a read error.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Both raid1 and raid10 create a mempool during startup.
If the 'alloc' function for this mempool fails, unplug_slaves
is called.
If that happens when the pool is being initialised, unplug_slaves
will try to use the 'conf' structure that isn't filled in yet, and
badness will happen.
So ensure that unplug_slaves doesn't get called unless we know
that the conf structure if fully initialised.
Signed-off-by: NeilBrown <neilb@suse.de>
During 'check' of a raid1 or raid10 it is possible for the management
thread to spend a lot of time running 'memcmp' on blocks from
different devices, so make sure the thread has a chance to schedule.
raid5d already has a cond_resched (in process_stripe).
Reported-By: Lee Howard <faxguy@howardsilvan.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Recently Jens has changed bio_rw_flagged() logic by following
commit 1f98a13f62. Now it returns
bool instead of int. This broke raid1/raid10 RW bits manipulation logic.
One of visible result is BUG_ON triggering due to empty barrier
here scsi_lib.c:1108 scsi_setup_fs_cmnd()
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The management thread for raid4,5,6 arrays are all called
mdX_raid5, independent of the actual raid level, which is wrong and
can be confusion.
So change md_register_thread to use the name from the personality
unless no alternate name (like 'resync' or 'reshape') is given.
This is simpler and more correct.
Cc: Jinzc <zhenchengjin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Get rid of any functions that test for these bits and make callers
use bio_rw_flagged() directly. Then it is at least directly apparent
what variable and flag they check.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As revalidate_disk calls check_disk_size_change, it will cause
any capacity change of a gendisk to be propagated to the blockdev
inode. So use that instead of mucking about with locks and
i_size_write.
Also add a call to revalidate_disk in do_md_run and a few other places
where the gendisk capacity is changed.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces md_integrity_check() by two new public functions:
md_integrity_register() and md_integrity_add_rdev() which are both
personality-independent.
md_integrity_register() is called from the ->run and ->hot_remove
methods of all personalities that support data integrity. The
function iterates over the component devices of the array and
determines if all active devices are integrity capable and if their
profiles match. If this is the case, the common profile is registered
for the mddev via blk_integrity_register().
The second new function, md_integrity_add_rdev() is called from the
->hot_add_disk methods, i.e. whenever a new device is being added
to a raid array. If the new device does not support data integrity,
or has a profile different from the one already registered, data
integrity for the mddev is disabled.
For raid0 and linear, only the call to md_integrity_register() from
the ->run method is necessary.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Switch MD over to the new disk_stack_limits() function which checks for
aligment and adjusts preferred I/O sizes when stacking.
Also indicate preferred I/O sizes where applicable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).
Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
A straight-forward conversion which gets rid of some
multiplications/divisions/shifts. The patch also introduces a couple
of new ones, most of which are due to conf->chunk_size still being
represented in bytes. This will be cleaned up in subsequent patches.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics. Since
is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
= is_power_of_2(chunk_sectors)
these bits don't need an adjustment for the shift.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
Convert all external users of queue limits to using wrapper functions
instead of poking the request queue variables directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's used by DM and MD and generally useful, so move the bio list
helpers into bio.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix this build error:
drivers/md/raid1.c: In function 'raid1_congested':
drivers/md/raid1.c:589: error: 'BDI_write_congested' undeclared
BDI_write_congested was changed in commit 1faa16d228 ("block: change the
request allocation/congestion logic to be sync/async based")
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit d3f761104b
newly allocated bvecs aren't initialised to NULL, so we have
to be more careful about freeing a bio which only managed
to get a few pages allocated to it. Otherwise the resync
process crashes.
This patch is appropriate for 2.6.29-stable.
Cc: stable@kernel.org
Cc: "Jens Axboe" <jens.axboe@oracle.com>
Reported-by: Gabriele Tozzi <gabriele@tozzi.eu>
Signed-off-by: NeilBrown <neilb@suse.de>
Allow userspace to set the size of the array according to the following
semantics:
1/ size must be <= to the size returned by mddev->pers->size(mddev, 0, 0)
a) If size is set before the array is running, do_md_run will fail
if size is greater than the default size
b) A reshape attempt that reduces the default size to less than the set
array size should be blocked
2/ once userspace sets the size the kernel will not change it
3/ writing 'default' to this attribute returns control of the size to the
kernel and reverts to the size reported by the personality
Also, convert locations that need to know the default size from directly
reading ->array_sectors to <pers>_size. Resync/reshape operations
always follow the default size.
Finally, fixup other locations that read a number of 1k-blocks from
userspace to use strict_blocks_to_sectors() which checks for unsigned
long long to sector_t overflow and blocks to sectors overflow.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Get personalities out of the business of directly modifying
->array_sectors. Lays groundwork to introduce policy on when
->array_sectors can be modified.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for giving userspace control over ->array_sectors we need
to be able to retrieve the 'default' size, and the 'anticipated' size
when a reshape is requested. For personalities that do not reshape emit
a warning if anything but the default size is requested.
In the raid5 case we need to update ->previous_raid_disks to make the
new 'default' size available.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
To be able to change the 'level' of an md/raid array, we need to
suspend the device so that no requests are active - then move some
pointers around etc.
The code already keeps counts of active requests and the ->quiesce
function can be used to wait until those counts hit zero.
However the quiesce function blocks new requests once they are all
ready 'inside' the personality module, and that is too late if we want
to replace the personality modules.
So make all md requests come in through a common md_make_request
function that keeps track of how many requests have entered the
modules but may not yet be on the internal reference counts.
Allow md_make_request to be blocked when we want to suspend the
device, and make it possible to wait for all those in-transit requests
to be added to internal lists so that ->quiesce can wait for them.
There is still a problem that when a request completes, we drop the
ref count inside the personality code so there is a short time between
when the refcount hits zero, and when the personality code is no
longer being used.
The personality code never blocks (schedule or spinlock) between
dropping the refcount and exiting the routine, so this should be safe
(as put_module calls synchronize_sched() before unmapping the module
code).
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the "size" field of struct mddev_s to "dev_sectors"
and stores the number of 512-byte sectors instead of the number of
1K-blocks in it.
All users of that field, including raid levels 1,4-6,10, are adjusted
accordingly. This simplifies the code a bit because it allows to get
rid of a couple of divisions/multiplications by two.
In order to make checkpatch happy, some minor coding style issues
have also been addressed. In particular, size_store() now uses
strict_strtoull() instead of simple_strtoull().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
There has been a race in raid10 and raid1 for a long time
which has only recently started showing up due to a scheduler changed.
When a sync_read request finishes, as soon as reschedule_retry
is called, another thread can mark the resync request as having
completed, so md_do_sync can finish, ->stop can be called, and
->conf can be freed. So using conf after reschedule_retry is not
safe.
Similarly, when finishing a sync_write, calling md_done_sync must be
the last thing we do, as it allows a chain of events which will free
conf and other data structures.
The first of these requires action in raid10.c
The second requires action in raid1.c and raid10.c
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If a raid1 only has a single working device and gets a read error,
we choose to simply return that error up to the filesystem (or whatever)
rather than failing the whole array.
However the codes doesn't quite do that. We attempt a readbalance
which allocates the same drive, so we retry the read - indefinitely.
Instead: If read_balance in the error case chooses the same drive that just
failed, treat it as a failure and don't retry.
Signed-off-by: NeilBrown <neilb@suse.de>
If a raid1 has only one working drive and it has a sector which
gives an error on read, then an attempt to recover onto a spare will
fail, but as the single remaining drive is not removed from the
array, the recovery will be immediately re-attempted, resulting
in an infinite recovery loop.
So detect this situation and don't retry recovery once an error
on the lone remaining drive is detected.
Allow recovery to be retried once every time a spare is added
in case the problem wasn't actually a media error.
Signed-off-by: NeilBrown <neilb@suse.de>
The rdev_for_each macro defined in <linux/raid/md_k.h> is identical to
list_for_each_entry_safe, from <linux/list.h>, it should be defined to
use list_for_each_entry_safe, instead of reinventing the wheel.
But some calls to each_entry_safe don't really need a safe version,
just a direct list_for_each_entry is enough, this could save a temp
variable (tmp) in every function that used rdev_for_each.
In this patch, most rdev_for_each loops are replaced by list_for_each_entry,
totally save many tmp vars; and only in the other situations that will call
list_del to delete an entry, the safe version is used.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
drivers/md/raid1.c: In function 'sync_request':
drivers/md/raid1.c:1759: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid1.o] Error 1
make[3]: *** Waiting for unfinished jobs....
drivers/md/raid10.c: In function 'sync_request':
drivers/md/raid10.c:1749: error: implicit declaration of function 'msleep_interruptible'
make[3]: *** [drivers/md/raid10.o] Error 1
drivers/md/md.c: In function 'md_do_sync':
drivers/md/md.c:5915: error: implicit declaration of function 'msleep'
Caused by commit 6caa3b0bbdb474647f6bdd8a958ffc46f78d8d58 ("md: Remove
unnecessary #includes, #defines, and function declarations"). I added
the following patch.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NeilBrown <neilb@suse.de>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch renames the array_size field of struct mddev_s to array_sectors
and converts all instances to use units of 512 byte sectors instead of 1k
blocks.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
md_allow_write() marks the metadata dirty while holding mddev->lock and then
waits for the write to complete. For externally managed metadata this causes a
deadlock as userspace needs to take the lock to communicate that the metadata
update has completed.
Change md_allow_write() in the 'external' case to start the 'mark active'
operation and then return -EAGAIN. The expected side effects while waiting for
userspace to write 'active' to 'array_state' are holding off reshape (code
currently handles -ENOMEM), cause some 'stripe_cache_size' change requests to
fail, cause some GET_BITMAP_FILE ioctl requests to fall back to GFP_NOIO, and
cause updates to 'raid_disks' to fail. Except for 'stripe_cache_size' changes
these failures can be mitigated by coordinating with mdmon.
md_write_start() still prevents writes from occurring until the metadata
handler has had a chance to take action as it unconditionally waits for
MD_CHANGE_CLEAN to be cleared.
[neilb@suse.de: return -EAGAIN, try GFP_NOIO]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For all array types but linear, ->hot_add_disk returns 1 on
success, 0 on failure.
For linear, it returns 0 on success and -errno on failure.
This doesn't cause a functional problem because the ->hot_add_disk
function of linear is used quite differently to the others.
However it is confusing.
So convert all to return 0 for success or -errno on failure
and fix call sites to match.
Signed-off-by: Neil Brown <neilb@suse.de>
i.e. extend the 'md/dev-XXX/slot' attribute so that you can
tell a device to fill an vacant slot in an and md array.
Signed-off-by: Neil Brown <neilb@suse.de>
When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.
For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.
We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
- We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
which causes the recovery not be be checkpointed.
- We remove spares and then re-added them which loses important state
information.
The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed. If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error. So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.
Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded). Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.
Issue: If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available, do we want to:
1/ complete the current rebuild, then go back and rebuild the new spare or
2/ restart the rebuild from the start and rebuild both devices in
parallel.
Both options can be argued for. The code currently takes option 2 as
a/ this requires least code change
b/ this results in a minimally-degraded array in minimal time.
Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When performing a "recovery" or "check" pass on a RAID1 array, we read
from each device and possible, if there is a difference or a read error,
write back to some devices.
We use the same 'bio' for both read and write, resetting various fields
between the two operations.
We forgot to reset bv_offset and bv_len however. These are often left
unchanged, but in the case where there is an IO error one or two sectors
into a page, they are changed.
This results in correctable errors not being corrected properly. It does
not result in any data corruption.
Cc: "Fairbanks, David" <David.Fairbanks@stratus.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible to add a write-intent bitmap to an active array, or remove
the bitmap that is there.
When we do with the 'quiesce' the array, which causes make_request to
block in "wait_barrier()".
However we are sampling the value of "mddev->bitmap" before the
wait_barrier call, and using it afterwards. This can result in using a
bitmap structure that has been freed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.
For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock. So always initialise that lock when allocated.
With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.
Thanks to Dan Williams for review and fixing the silly bugs.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allows a userspace metadata handler to take action upon detecting a device
failure.
Based on an original patch by Neil Brown.
Changes:
-added blocked_wait waitqueue to rdev
-don't qualify Blocked with Faulty always let userspace block writes
-added md_wait_for_blocked_rdev to wait for the block device to be clear, if
userspace misses the notification another one is sent every 5 seconds
-set MD_RECOVERY_NEEDED after clearing "blocked"
-kill DoBlock flag, just test mddev->external
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character. It may also output a trailing space
before newline. klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file. This looks ugly.
Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar. Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown