The last CVT standard introduced reduced blanking version 2 which is signaled by
a vsync of 8. Log this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added support for reduced blanking version 2 (RB v2) in cvt timings.
Standard specifies a fixed vsync pulse of 8 lines to indicate RB v2
timings. Vertical back porch is fixed at 6 lines and vertical front
porch is remainder of vertical blanking time.
For RB v2, horizontal blanking is fixed at 80 pixels. Horizontal sync
is fixed at 32. All horizontal timing counts (active pixels, front,
back porches) can be specified upto a precision of 1.
RB v2 allows for non standard aspect ratios. In RB v2 vsync does not
indicate aspect ratio. In absence of aspect ratio v4l2_detect_cvt()
cannot calculate image width from image height. Hence extending the
v4l2_detect_cvt() to pass image width in case of RB v2.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RC_ST and IR_SUNXI entries have weird indentation, and the RC_ST
entry is actually malformed. Fix it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
solo_dev and pdev cannot be NULL here. It doesn't matter if we
initialized the PCI device or not.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
readl() and writel() are atomic, we don't need the spin lock.
Also, flushing posted write buffer isn't required. Especially on read :-)
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes a panic on ARM. Diagnosis by Russell King.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The period count is fixed, don't confuse ALSA.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the sequence counter: we're counting frames, not fields.
Also remove the unused 'field' field. That would only be needed if this driver
would support V4L2_FIELD_ALTERNATE.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVmXEeAAoJEHm+PkMAQRiGdIYIAJLyPXCXyG5gqvjw7ZCfwqdP
DsXgh89STQ0h9D26ZVj9HltKqaq4GDUnpaaSBgmd7QcHYEQczF3A81TaoeWOMpwm
qpItrNUZECYsNHvg4SWxZ7wm6psJugYkIT51T+7xk9QCbYSXKdd0aXyZ+aic7JXh
/AOlasJd9WxHw6wtqPxW+N+h0F02Gl5PxcIC/Rn70cBjScN6kOCDxpIEeGtrkOcM
LjLnLU1+LBaLpsdKOTWoOb4kCtB1DnpPBtpC09ApBgTBfFyc2TiqngIeQV985zps
9YYnKqBgUnZHoVpFItvXaSYM2suKGHTV98iIQ43Yu5NsAIJk9Q0EhSKlhUR5mQw=
=c1wk
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc1' into patchwork
Linux 4.2-rc1
* tag 'v4.2-rc1': (12415 commits)
Linux 4.2-rc1
bluetooth: fix list handling
9p: cope with bogus responses from server in p9_client_{read,write}
p9_client_write(): avoid double p9_free_req()
9p: forgetting to cancel request on interrupted zero-copy RPC
dax: bdev_direct_access() may sleep
block: Add support for DAX reads/writes to block devices
dax: Use copy_from_iter_nocache
dax: Add block size note to documentation
NTB: Add split BAR output for debugfs stats
NTB: Change WARN_ON_ONCE to pr_warn_once on unsafe
NTB: Print driver name and version in module init
NTB: Increase transport MTU to 64k from 16k
NTB: Rename Intel code names to platform names
NTB: Default to CPU memcpy for performance
NTB: Improve performance with write combining
NTB: Use NUMA memory in Intel driver
NTB: Use NUMA memory and DMA chan in transport
NTB: Rate limit ntb_qp_link_work
NTB: Add tool test client
...
Without setting the direction of a gpio to output a call to
gpiod_set_value doesn't have a defined outcome.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull LED subsystem updates from Bryan Wu:
"In this cycle, we finished to merge patches for LED Flash class
driver.
Other than that we have some bug fixes and new drivers for LED
controllers"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (33 commits)
leds:lp55xx: fix firmware loading error
leds: fix max77693-led build errors
leds: fix aat1290 build errors
leds: aat1290: pass flags parameter to devm_gpiod_get
leds: ktd2692: pass flags parameter to devm_gpiod_get
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
leds: aat1290: add support for V4L2 Flash sub-device
DT: aat1290: Document handling external strobe sources
leds: max77693: add support for V4L2 Flash sub-device
media: Add registration helpers for V4L2 flash sub-devices
v4l: async: Add a pointer to of_node to struct v4l2_subdev, match it
Documentation: leds: Add description of v4l2-flash sub-device
leds: add BCM6358 LED driver
leds: add DT binding for BCM6358 LED controller
leds: fix brightness changing when software blinking is active
Documentation: leds-lp5523: describe master fader attributes
leds: lp5523: add master_fader support
leds: leds-gpio: Allow compile test if !GPIOLIB
leds: leds-gpio: Add missing #include <linux/of.h>
gpiolib: Add missing dummies for the unified device properties interface
...
To be consistent with other kernel interface namings, rename
of_get_named_gen_pool() to of_gen_pool_get(). In the original function
name "_named" suffix references to a device tree property, which contains
a phandle to a device and the corresponding device driver is assumed to
register a gen_pool object.
Due to a weak relation and to avoid any confusion (e.g. in future
possible scenario if gen_pool objects are named) the suffix is removed.
[sfr@canb.auug.org.au: crypto/marvell/cesa - fix up for of_get_named_gen_pool() rename]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be consistent with other genalloc interface namings, rename
dev_get_gen_pool() to gen_pool_get(). The original omitted "dev_" prefix
is removed, since it points to argument type of the function, and so it
does not bring any useful information.
[akpm@linux-foundation.org: update arch/arm/mach-socfpga/pm.c]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Mark Brown <broonie@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alan Tull <atull@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big, really big, staging tree patches for 4.2-rc1.
Loads of stuff in here, almost all just coding style fixes / churn, and
a few new drivers as well, one of which I just disabled from the build a
few minutes ago due to way too many build warnings.
Other than the one "disable this driver" patch, all of these have been
in linux-next for quite a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNpc0ACgkQMUfUDdst+ym8EgCg0pL1Qcf9Se3jAc96fLt+itpv
Rd0AoI9uJcq8Qm7d+IXnz3ojLnN9xvN3
=xt0u
-----END PGP SIGNATURE-----
Merge tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big, really big, staging tree patches for 4.2-rc1.
Loads of stuff in here, almost all just coding style fixes / churn,
and a few new drivers as well, one of which I just disabled from the
build a few minutes ago due to way too many build warnings.
Other than the one "disable this driver" patch, all of these have been
in linux-next for quite a while with no reported issues"
* tag 'staging-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1163 commits)
staging: wilc1000: disable driver due to build warnings
Staging: rts5208: fix CHANGE_LINK_STATE value
Staging: sm750fb: ddk750_swi2c.c: Insert spaces before parenthesis
Staging: sm750fb: ddk750_swi2c.c: Place braces on correct lines
Staging: sm750fb: ddk750_swi2c.c: Insert spaces around operators
Staging: sm750fb: ddk750_swi2c.c: Replace spaces with tabs
Staging: sm750fb: ddk750_swi2c.h: Shorten lines to under 80 characters
Staging: sm750fb: ddk750_swi2c.h: Replace spaces with tabs
Staging: sm750fb: modedb.h: Shorten lines to under 80 characters
Staging: sm750fb: modedb.h: Replace spaces with tabs
staging: comedi: addi_apci_3120: rename 'this_board' variables
staging: comedi: addi_apci_1516: rename 'this_board' variables
staging: comedi: ni_atmio: cleanup ni_getboardtype()
staging: comedi: vmk80xx: sanity check context used to get the boardinfo
staging: comedi: vmk80xx: rename 'boardinfo' variables
staging: comedi: dt3000: rename 'this_board' variables
staging: comedi: adv_pci_dio: rename 'this_board' variables
staging: comedi: cb_pcidas64: rename 'thisboard' variables
staging: comedi: cb_pcidas: rename 'thisboard' variables
staging: comedi: me4000: rename 'thisboard' variables
...
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.2.
I've one other new driver from freescale on my radar, it's been posted
and reviewed, I'd just like to get someone to give it a last look, so
maybe I'll send it or maybe I'll leave it.
There is no major nouveau changes in here, Ben was working on
something big, and we agreed it was a bit late, there wasn't anything
else he considered urgent to merge.
There might be another msm pull for some bits that are waiting on
arm-soc, I'll see how we time it.
This touches some "of" stuff, acks are in place except for the fixes
to the build in various configs,t hat I just applied.
Summary:
New drivers:
- virtio-gpu:
KMS only pieces of driver for virtio-gpu in qemu.
This is just the first part of this driver, enough to run
unaccelerated userspace on. As qemu merges more we'll start
adding the 3D features for the virgl 3d work.
- amdgpu:
a new driver from AMD to driver their newer GPUs. (VI+)
It contains a new cleaner userspace API, and is a clean
break from radeon moving forward, that AMD are going to
concentrate on. It also contains a set of register headers
auto generated from AMD internal database.
core:
- atomic modesetting API completed, enabled by default now.
- Add support for mode_id blob to atomic ioctl to complete interface.
- bunch of Displayport MST fixes
- lots of misc fixes.
panel:
- new simple panels
- fix some long-standing build issues with bridge drivers
radeon:
- VCE1 support
- add a GPU reset counter for userspace
- lots of fixes.
amdkfd:
- H/W debugger support module
- static user-mode queues
- support killing all the waves when a process terminates
- use standard DECLARE_BITMAP
i915:
- Add Broxton support
- S3, rotation support for Skylake
- RPS booting tuning
- CPT modeset sequence fixes
- ns2501 dither support
- enable cmd parser on haswell
- cdclk handling fixes
- gen8 dynamic pte allocation
- lots of atomic conversion work
exynos:
- Add atomic modesetting support
- Add iommu support
- Consolidate drm driver initialization
- and MIC, DECON and MIPI-DSI support for exynos5433
omapdrm:
- atomic modesetting support (fixes lots of things in rewrite)
tegra:
- DP aux transaction fixes
- iommu support fix
msm:
- adreno a306 support
- various dsi bits
- various 64-bit fixes
- NV12MT support
rcar-du:
- atomic and misc fixes
sti:
- fix HDMI timing complaince
tilcdc:
- use drm component API to access tda998x driver
- fix module unloading
qxl:
- stability fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
drm/nouveau: Pause between setting gpu to D3hot and cutting the power
drm/dp/mst: close deadlock in connector destruction.
drm: Always enable atomic API
drm/vgem: Set unique to "vgem"
of: fix a build error to of_graph_get_endpoint_by_regs function
drm/dp/mst: take lock around looking up the branch device on hpd irq
drm/dp/mst: make sure mst_primary mstb is valid in work function
of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
drm/atomic: Don't set crtc_state->enable manually
drm/exynos: dsi: do not set TE GPIO direction by input
drm/exynos: dsi: add support for MIC driver as a bridge
drm/exynos: dsi: add support for Exynos5433
drm/exynos: dsi: make use of array for clock access
drm/exynos: dsi: make use of driver data for static values
drm/exynos: dsi: add macros for register access
drm/exynos: dsi: rename pll_clk to sclk_clk
drm/exynos: mic: add MIC driver
of: add helper for getting endpoint node of specific identifiers
drm/exynos: add Exynos5433 decon driver
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJ/U
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvements at the DVB API DocBook documentation. Now, the
frontend and the network APIs are fully in sync with the Kernel and
looks more like the rest of the media documentation;
- New frontend driver: cx24120
- New driver for a PCI device: cobalt. This driver is actually not
sold in the market, but it is a good example of a multi-HDMI input
device;
- The dt3155 driver were promoted from staging;
- The mantis driver got remote controller support;
- New V4L2 driver for ST bdisp SoC chipsets;
- Make sparse and smatch happier: several bugs were solved by fixing
the issues reported by those static code analyzers.
- Lots of new device additions, new features, improvements and cleanups
at the existing drivers.
* tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (553 commits)
[media] lmedm04: fix the range for relative measurements
[media] lmedm04: use u32 instead of u64 for relative stats
[media] omap3isp: remove unused var
[media] saa7134: fix page size on some archs
[media] use CONFIG_PM_SLEEP for suspend/resume
[media] tuner-i2c: be consistent with I2C declaration
[media] si470x: cleanup define namespace
[media] bdisp: prevent compiling on random arch
[media] vb2: Don't WARN when v4l2_buffer.bytesused is 0 for multiplanar buffers
[media] MAINTAINERS: Add entry for the Renesas VSP1 driver
[media] videodev2.h: fix copy-and-paste error in V4L2_MAP_XFER_FUNC_DEFAULT
[media] Revert "[media] vb2: Push mmap_sem down to memops"
[media] mantis: cleanup a warning
[media] bdisp-debug: don't try to divide by s64
[media] cx88: don't declare restart_video_queue if not used
[media] au0828: move dev->boards atribuition to happen earlier
[media] lmedm04: implement dvb v5 statistics
[media] bdisp: remove unused var
[media] bdisp: remove needless check
ts2020: fix compilation on i386
...
Relative measurements are typically between 0 and 0xffff. However,
for some tuners (TUNER_S7395 and TUNER_S0194), the range were from
0 to 0xff00, with means that 100% is never archived.
Also, TUNER_RS2000 uses a more complex math.
So, create a macro that does the conversion using bit operations
and use it for all conversions.
The code is also easier to read with is a bonus.
While here, remove a bogus comment.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cleanup this sparse warning:
drivers/media/usb/dvb-usb-v2/lmedm04.c:302 lme2510_update_stats() warn: should '((255 - st->signal_sn - 161) * 3) << 8' be a 64 bit type?
Both c_tmp and s_tmp actually stores a u16 stat. Using a u64 data
there is a waste, specially on u32 archs, as 64 ints there are more
expensive.
So, change the types to u32 and do the typecast only when storing
the result.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/platform/omap3isp/isppreview.c:932:6: warning: variable ‘features’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On some archs, like tile, the PAGE_SIZE is not 4K. In the case
of tile arch, it can be either 16KB or 64KB.
Due to that, a warning is produced:
drivers/media/pci/saa7134/saa7134.h:678:43: warning: large integer implicitly truncated to unsigned type [-Woverflow]
This is actually an error, as it will write trach to the DMA size
registers. The logic at saa7134-ts already does the right thing:
saa_writeb(SAA7134_TS_DMA0, ((dev->ts.nr_packets-1)&0xff));
saa_writeb(SAA7134_TS_DMA1, (((dev->ts.nr_packets-1)>>8)&0xff));
/* TSNOPIT=0, TSCOLAP=0 */
saa_writeb(SAA7134_TS_DMA2,
((((dev->ts.nr_packets-1)>>16)&0x3f) | 0x00));
So, fix the driver to take larger page sizes into account.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using CONFIG_PM_SLEEP suppress the warnings when the driver is
compiled without PM sleep functions:
drivers/media/rc/st_rc.c:338:12: warning: ‘st_rc_suspend’ defined but not used [-Wunused-function]
drivers/media/rc/st_rc.c:359:12: warning: ‘st_rc_resume’ defined but not used [-Wunused-function]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
On alpha, gcc warns a log about signed/unsigned ballance, with
produces 3185 warnings. Ok, this is bogus, but it indicates that
the declaration at V4L2 side is not consistent with the one at
I2C.
With this trivial patch, the number of errors reduce to 2959
warnings. Still too much, but it is 7.1% less. So let's do it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
This patch adds helper functions for registering/unregistering
LED Flash class devices as V4L2 sub-devices. The functions should
be called from the LED subsystem device driver. In case the
support for V4L2 Flash sub-devices is disabled in the kernel
config the functions' empty versions will be used.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some architectures already use CHIPID defines:
drivers/media/radio/si470x/radio-si470x.h:57:0: warning: "CHIPID" redefined [enabled by default]
drivers/media/radio/si470x/radio-si470x.h:57:0: warning: "CHIPID" redefined [enabled by default]
drivers/media/radio/si470x/radio-si470x.h:57:0: warning: "CHIPID" redefined [enabled by default]
So, use SI_foo namespace to avoid conflicts.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver requires support for DMA attrs function, and not
just DMA. Change the options accordingly to remove those errors:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_free_nodes’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:132:3: error: implicit declaration of function ‘dma_free_attrs’ [-Werror=implicit-function-declaration]
dma_free_attrs(ctx->bdisp_dev->dev,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_alloc_nodes’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:157:9: error: implicit declaration of function ‘dma_alloc_attrs’ [-Werror=implicit-function-declaration]
base = dma_alloc_attrs(dev, node_size * MAX_NB_NODE, &paddr,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:157:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = dma_alloc_attrs(dev, node_size * MAX_NB_NODE, &paddr,
^
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c: In function ‘bdisp_hw_alloc_filters’:
/devel/v4l/to_next/drivers/media/platform/sti/bdisp/bdisp-hw.c:219:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
base = dma_alloc_attrs(dev, size, &paddr, GFP_KERNEL | GFP_DMA, &attrs);
Also, get rid of bogus, unused and duplicated symbol declaration
for the config option done at bdisp/Kconfig.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit f61bf13b6a ("[media] vb2: add allow_zero_bytesused flag to the
vb2_queue struct") added a WARN_ONCE to catch usage of a deprecated API
using a zero value for v4l2_buffer.bytesused.
However, the condition is checked incorrectly, as the v4L2_buffer
bytesused field is supposed to be ignored for multiplanar buffers. This
results in spurious warnings when using the multiplanar API.
Fix it by checking v4l2_buffer.bytesused for uniplanar buffers and
v4l2_plane.bytesused for multiplanar buffers.
Fixes: f61bf13b6a ("[media] vb2: add allow_zero_bytesused flag to the vb2_queue struct")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: stable@vger.kernel.org # for v4.0
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/pci/mantis/mantis_i2c.c: In function 'mantis_i2c_init':
drivers/media/pci/mantis/mantis_i2c.c:222:15: warning: variable 'intmask' set but not used [-Wunused-but-set-variable]
u32 intstat, intmask;
We are burrying direct access to MTRR code support on
x86 in order to take advantage of PAT. In the future, we
also want to make the default behavior of ioremap_nocache()
to use strong UC, at which point the use of mtrr_add() on
those systems would make write-combining void.
In order to help both enable us to later make strong
UC default and in order to phase out direct MTRR access
code, port the driver over to the arch_phys_wc_add() API
and annotate that the device driver requires systems to
boot with PAT disabled, with the 'nopat' kernel parameter.
This is a workable compromise given that the hardware is
really rare these days, and perhaps only some lost souls
stuck with obsolete hardware are expected to be using this
feature of the device driver.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Stefan Bader <stefan.bader@canonical.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ville Syrjälä <syrjala@sci.fi>
Cc: bhelgaas@google.com
Cc: konrad.wilk@oracle.com
Cc: linux-media@vger.kernel.org
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Link: http://lkml.kernel.org/r/1434053994-2196-2-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since when we start discussions about the usage Media Controller for
complex hardware, one thing become clear: the way it is, MC fails to
map anything different than capture/output/m2m video-only streaming.
The point is that MC has entities named as devnodes, but the only
devnode used (before the DVB patches) is MEDIA_ENT_T_DEVNODE_V4L.
Due to the way MC got implemented, however, this entity actually
doesn't represent the devnode, but the hardware I/O engine that
receives data via DMA.
By coincidence, such DMA is associated with the V4L device node
on webcam hardware, but this is not true even for other V4L2
devices. For example, on USB hardware, the DMA is done via the
USB controller. The data passes though a in-kernel filter that
strips off the URB headers. Other V4L2 devices like radio may not
even have DMA. When it have, the DMA is done via ALSA, and not
via the V4L devnode.
In other words, MC is broken as a whole, but tagging it as BROKEN
right now would do more harm than good.
So, instead, let's mark, for now, the DVB part as broken and
block all new changes to MC while we fix this mess, whith
we hopefully will do for the next Kernel version.
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
V4L2 async sub-devices are currently matched (OF case) based on the struct
device_node pointer in struct device. LED devices may have more than one
LED, and in that case the OF node to match is not directly the device's
node, but a LED's node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
There are several warnings there, on some architectures, related
to dividing a s32 by a s64 value:
drivers/media/platform/sti/bdisp/bdisp-debug.c:594: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:594: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:594: warning: passing argument 1 of '__div64_32' from incompatible pointer type
drivers/media/platform/sti/bdisp/bdisp-debug.c:595: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:595: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:595: warning: passing argument 1 of '__div64_32' from incompatible pointer type CC [M] drivers/media/tuners/mt2060.o
drivers/media/platform/sti/bdisp/bdisp-debug.c:596: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:596: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:596: warning: passing argument 1 of '__div64_32' from incompatible pointer type
drivers/media/platform/sti/bdisp/bdisp-debug.c:597: warning: comparison of distinct pointer types lacks a cast
drivers/media/platform/sti/bdisp/bdisp-debug.c:597: warning: right shift count >= width of type
drivers/media/platform/sti/bdisp/bdisp-debug.c:597: warning: passing argument 1 of '__div64_32' from incompatible pointer type
That doesn't make much sense. What the driver is actually trying
to do is to divide one second by a value. So, check the range
before dividing. That warrants the right result and will remove
the warnings on non-64 bits archs.
Also fixes this warning:
drivers/media/platform/sti/bdisp/bdisp-debug.c:588: warning: comparison of distinct pointer types lacks a cast
by using div64_s64() instead of calling do_div() directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While compiled on alpha, got this error:
drivers/media/pci/cx88/cx88-video.c:415:12: warning: 'restart_video_queue' defined but not used [-Wunused-function]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The attribution of dev->boards occured too late, which
would couse an OOPS in media controller registration.
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Indroduce function lme2510_update_stats to update
statistics directly from usb interrupt.
Provide signal and snr wrap rounds for dvb v3 functions.
Block and post bit are not available.
When i2c_talk_onoff is on no statistics are available,
with possible future hand over to the relevant frontend/tuner.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the following warning:
drivers/media/platform/sti/bdisp/bdisp-v4l2.c: In function 'bdisp_register_device':
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:1024:26: warning: variable 'pdev' set but not used [-Wunused-but-set-variable]
struct platform_device *pdev;
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:947 bdisp_s_selection() warn: unsigned 'out.width' is never less than zero.
drivers/media/platform/sti/bdisp/bdisp-v4l2.c:947 bdisp_s_selection() warn: unsigned 'out.height' is never less than zero.
Indeed, width and height are unsigned.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/built-in.o: In function `ts2020_read_signal_strength':
ts2020.c:(.text+0x298ff94): undefined reference to `__divdi3'
ts2020.c:(.text+0x298ffd4): undefined reference to `__divdi3'
ts2020.c:(.text+0x298fffd): undefined reference to `__divdi3'
Makefile:921: recipe for target 'vmlinux' failed
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The embedded UART is apparently used to receive decoded IR (RC5?) codes.
Forward these scan codes to the RC framework and (where known) add
corresponding mapping tables to translate them into regular keys.
This patch has been tested on a TechniSat CableStar HD2. The mappings of other
rc-maps were taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/) and the s2-liplianin repository. The
major difference to Christoph's patch is a reworked interrupt handling of the
UART because the RX interrupt is apparently level triggered and requires
masking until the FIFO is read by the UART worker.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS35 remote is distributed with TechniSat CableStar HD2 cards (mantis
chipset). The exact protocol type is unknown, making this rc map probably only
usable by mantis cards.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Quite a few of the ->diseqc_send_master_cmd() implementations don't
check cmd->msg_len so it can lead to memory corruption.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit ad90b6b0f1.
This patch breaks I2C communication towards Si2168. After reverting and
applying the other patch in this series the I2C communication is
correct.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The i2c_reg_len for Si2168 should be 0 for correct I2C communication.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In little endian cases, macro cpu_to_be16 unfolds to __swab16 which
provides special case for constants. In big endian cases,
__constant_cpu_to_be16 and cpu_to_be16 expand directly to the
same expression. So, replace __constant_cpu_to_be16 with
cpu_to_be16 with the goal of getting rid of the definition of
__constant_cpu_to_be16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_be16(x)
+ cpu_to_be16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Following a change made to TS2020 tuner in patches
ts2020: Provide DVBv5 API signal strength
ts2020: Allow stats polling to be suppressed
Polling on the driver must be suppressed because
the demuxer is stopped by I2C messages.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Statistics polling can not be done by lmedm04 driver's implementation of
M88RS2000/TS2020 because I2C messages stop the device's demuxer, so allow
polling for statistics to be suppressed in the ts2020 driver by setting
dont_poll in the ts2020_config struct.
Reported-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Copy the loop_through setting from the ts2020_config struct to the internal
ts2020_priv struct so that it can actually be used.
Whilst we're at it, group the bitfields together in the same order in both
structs so that the compiler has a good chance to copy them in one go.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide a DVBv5 API signal strength. This is in units of 0.001 dBm rather
than a percentage.
>From Antti Palosaari's testing with a signal generator, it appears that the
gain calculated according to Montage's specification if negated is a
reasonable representation of the signal strength of the generator.
To this end:
(1) Polled statistic gathering needed to be implemented in the TS2020 driver.
This is done in the ts2020_stat_work() function.
(2) The calculated gain is placed as the signal strength in the
dtv_property_cache associated with the front end with the scale set to
FE_SCALE_DECIBEL.
(3) The DVBv3 format signal strength then needed to be calculated from the
signal strength stored in the dtv_property_cache rather than accessing
the value when ts2020_read_signal_strength() is called.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS2020 and TS2022 tuners take an input from the demodulator indicating the
AGC setting on that component that is then used to influence the tuner's own
gain. This should be taken into account when calculating the gain and signal
strength.
Further, the existing TS2020 driver miscalculates the signal strength as the
result of its calculations can exceed the storage capacity of the 16-bit word
used to return it to userspace.
To this end:
(1) Add a callback function (->get_agc_pwm()) in the ts2020_config struct that
the tuner can call to get the AGC PWM value from the demodulator.
(2) Modify the TS2020 driver to calculate the gain according to Montage's
specification with the adjustment that we produce a negative value and
scale it to 0.001dB units (which is what the DVBv5 API will require):
(a) Callback to the demodulator to retrieve the AGC PWM value and then
turn that into Vagc for incorporation in the calculations. If the
callback is unset, assume a Vagc of 0.
(b) Calculate the tuner gain from a combination of Vagc and the tuner's RF
gain and baseband gain settings.
(3) Turn this into a percentage signal strength as per Montage's
specification for return to userspace with the DVBv3 API.
(4) Provide a function in the M88DS3103 demodulator driver that can be used to
get the AGC PWM value on behalf of the tuner.
(5) The ts2020_config.get_agc_pwm function should be set by the code that
stitches together the drivers for each card.
For the DVBSky cards that use the M88DS3103 with the TS2020 or the TS2022,
set the get_agc_pwm function to point to m88ds3103_get_agc_pwm.
I have tested this with a DVBSky S952 card which has an M88DS3103 and a TS2022.
Thanks to Montage for providing access to information about the workings of
these parts.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use regmap for I2C register access.
Remove own I2C repeated mutex as it should not be needed. I2C adapter
lock is already taken when I2C mux adapter is called, no need for
double locking.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename driver state from priv to dev.
Use I2C client for correct logging.
Use adapter and address from I2C client structure where needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ts2020_attach() allocates a variable pdata on the stack and then passes a
pointer to it to i2c_new_device() which stashes the pointer in persistent
structures.
Add a comment to the effect that this isn't actually an error because the
contents of the variable are only used in ts2020_probe() and this is only
called ts2020_attach()'s stack frame exists.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register driver using I2C bindings internally when legacy media
attach is used. That is done by registering driver using I2C binding
from legacy attach. That way we can get valid I2C client, which is
needed for proper dev_() logging and regmap for example even legacy
binding is used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* We don't need calculate channel bandwidth from symbol rate as it
is calculated by DVB core.
* Use clamp() to force upper/lower limit of filter 3dB frequency.
Upper limit should never exceeded 40MHz (80MHz BW) in any case,
though...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used frequency synthesizer is simple Integer-N PLL, with configurable
reference divider, output divider and of course N itself. Old
calculations were working fine, but not so easy to understand.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are still some 64-bit division problems in the cobalt code.
Replace it by div_u64.
[mchehab@osg.samsung.com: folded with an additional diff sent by
Hans via a priv e-mail]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't allow sleep when getting the gpio value in the irq-handler.
On my rk3288 board this results in might_sleep warnings when receiving
data like:
BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1531
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: P 4.1.0-rc5+ #2011
Hardware name: Rockchip (Device Tree)
[<c00189a0>] (unwind_backtrace) from [<c0013b04>] (show_stack+0x20/0x24)
[<c0013b04>] (show_stack) from [<c0757970>] (dump_stack+0x8c/0xbc)
[<c0757970>] (dump_stack) from [<c0053188>] (___might_sleep+0x238/0x284)
[<c0053188>] (___might_sleep) from [<c0053264>] (__might_sleep+0x90/0xa4)
[<c0053264>] (__might_sleep) from [<c02ff4ac>] (gpiod_get_raw_value_cansleep+0x28/0x44)
[<c02ff4ac>] (gpiod_get_raw_value_cansleep) from [<bf0363c4>] (gpio_ir_recv_irq+0x24/0x6c [gpio_ir_recv])
[<bf0363c4>] (gpio_ir_recv_irq [gpio_ir_recv]) from [<c008a78c>] (handle_irq_event_percpu+0x164/0x550)
[<c008a78c>] (handle_irq_event_percpu) from [<c008abc4>] (handle_irq_event+0x4c/0x6c)
[<c008abc4>] (handle_irq_event) from [<c008df88>] (handle_edge_irq+0x128/0x150)
[<c008df88>] (handle_edge_irq) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c02fc4cc>] (rockchip_irq_demux+0x158/0x210)
[<c02fc4cc>] (rockchip_irq_demux) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c008a058>] (__handle_domain_irq+0x98/0xc0)
[<c008a058>] (__handle_domain_irq) from [<c00094a4>] (gic_handle_irq+0x4c/0x70)
[<c00094a4>] (gic_handle_irq) from [<c0014684>] (__irq_svc+0x44/0x5c)
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
struct timeval uses a 32-bit seconds representation which will
overflow in the year 2038 and beyond. This patch replaces
the usage of struct timeval with ktime_t which is a 64-bit
timestamp and is year 2038 safe.
This patch is part of a larger attempt to remove all instances
of 32-bit timekeeping variables (timeval, timespec, time_t)
which are not year 2038 safe, from the kernel.
[mchehab@osg.samsung.com: add a missing parenthesis, breaking compilation]
Suggested-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The flexcop bridge chip has two banks of hardware pid filters -
an initial 6, and on some chip revisions an additional bank of 32.
A bug is present on the initial 6 - when changing transponders
one of two PAT packets from the old transponder would be included
in the initial packets from the new transponder. This usually
transpired with userspace programs complaining about services
missing, because they are seeing a PAT that they would not be
expecting. Running in full TS mode does not exhibit this problem,
neither does using just the additional 32.
This patch adds in an option to not use the inital 6 and solely use
just the additional 32, and enables this option for the SkystarS2
card. Other cards can be added as required if they also have
this bug.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
My static checker detected that free_irq() is called even after
request_irq() failed in ddb_probe(). In this case, the kernel may try to
free dev->pdev->irq although the IRQ is not assigned. This event rarely
occurs, but always introduces a warning if it happens.
"goto fail1" always results in disabling enabled MSI and releasing a
requested IRQ. It seems like the former handling is necessary. So I added
a conditional branch before the free_irq() (stat == 0 means request_irq()
succeeds).
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add AverMedia AverTV/505 card to saa7134 driver. It is a card bearing
SAA7130HL chip and FQ1216ME/IH-3 tuner.
Working: Composite, TV and IR remote control.
Untested: S-Video.
[mchehab@osg.samsung.com: fix CodingStyle]
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Compilation warning issued by kbuild test robot:
>> drivers/media/common/b2c2/flexcop-fe-tuner.c:31:12: warning: 'flexcop_fe_request_firmware' defined but not used [-Wunused-function]
static int flexcop_fe_request_firmware(struct dvb_frontend *fe,
This patch fixes a mismatch in Kconfig define checks. One had a
check for just CX24120, the other is checking for both CX24120
and ISL6421.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the Terratec Grabby with USB ID 0ccd:00a6.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The coda tracing code causes lots of warnings like
In file included from /git/arm-soc/include/trace/define_trace.h:90:0,
from /git/arm-soc/drivers/media/platform/coda/trace.h:203,
from /git/arm-soc/drivers/media/platform/coda/coda-bit.c:34:
/git/arm-soc/include/trace/ftrace.h:28:0: warning: "TRACE_SYSTEM_STRING" redefined
#define TRACE_SYSTEM_STRING __app(TRACE_SYSTEM_VAR,__trace_system_name)
^
In file included from /git/arm-soc/include/trace/define_trace.h:83:0,
from /git/arm-soc/drivers/media/platform/coda/trace.h:203,
from /git/arm-soc/drivers/media/platform/coda/coda-bit.c:34:
/git/arm-soc/drivers/media/platform/coda/./trace.h:12:0: note: this is the location of the previous definition
#define TRACE_SYSTEM_STRING __stringify(TRACE_SYSTEM)
>From what I can tell, this is just the result of a bogus TRACE_SYSTEM_STRING
definition, and removing that one makes the warnings go away.
Fixes: 9a1a8f9953 ("[media] coda: Add tracing support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some USB drivers have a logic at the VB buffer handling like:
if (in_interrupt())
BUG();
Use, instead:
BUG_ON(in_interrupt());
Btw, this logic looks weird on my eyes. We should convert them
to use VB2, in order to avoid those crappy things.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The subdev API is optional. No driver should depend on it.
Avoid compilation breakages if subdev API is not selected:
drivers/media/i2c/ov2659.c: In function ‘ov2659_get_fmt’:
drivers/media/i2c/ov2659.c:1054:3: error: implicit declaration of function ‘v4l2_subdev_get_try_format’ [-Werror=implicit-function-declaration]
mf = v4l2_subdev_get_try_format(sd, cfg, 0);
^
drivers/media/i2c/ov2659.c:1054:6: warning: assignment makes pointer from integer without a cast
mf = v4l2_subdev_get_try_format(sd, cfg, 0);
^
drivers/media/i2c/ov2659.c: In function ‘ov2659_set_fmt’:
drivers/media/i2c/ov2659.c:1129:6: warning: assignment makes pointer from integer without a cast
mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
^
drivers/media/i2c/ov2659.c: In function ‘ov2659_open’:
drivers/media/i2c/ov2659.c:1264:38: error: ‘struct v4l2_subdev_fh’ has no member named ‘pad’
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Creates 5 debugfs entries to dump the last HW request, the last HW node
(=command), the HW registers and the recent HW performance (time & fps)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This v4l2 mem2mem driver is a 2D blitter for STMicroelectronics SoC.
It uses the v4l2 mem2mem framework.
The following features are supported and tested:
- Color format conversion (RGB32, RGB24, RGB16, NV12, YUV420P)
- Copy
- Scale
- Flip
- Deinterlace
- Wide (4K) picture support
- Crop
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added missing slab.h include to bdisp-v4l2.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB API was originally defined using typedefs. This is against
Kernel CodingStyle, and there's no good usage here. While we can't
remove its usage on userspace, we can avoid its usage in Kernelspace.
So, let's do it.
This patch was generated by this shell script:
for j in $(grep typedef include/uapi/linux/dvb/frontend.h |cut -d' ' -f 3); do for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f); do sed "s,${j}_t,enum $j," <$i >a && mv a $i; done; done
While here, make CodingStyle fixes on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> # for drivers/media/firewire/*
Fix this compiler warning by allocating a structure to read the eeprom instead
of doing it on the stack and worse: the eeprom array is static, so that can
cause problems if there are multiple cx231xx instances.
cx231xx-cards.c: In function 'cx231xx_card_setup':
cx231xx-cards.c:1110:1: warning: the frame size of 2064 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
I did consider removing the code altogether since the result is actually
not used at the moment, but I decided against it since it is used in other
drivers and someone might want to start using it in this driver as well. And
then it is useful that the code is already there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Extend detect_cvt/gtf API to indicate the format type (interlaced
or progressive). In case of interlaced, the vertical front and back
porch and vsync values for both (odd,even) fields are considered to
derive image height. Populated vsync, vertical front, back porch
values in bt timing structure for even and odd fields and updated
the flags appropriately.
Also modified the functions calling the detect_cvt/gtf(). As of now
these functions are calling detect_cvt/gtf() with interlaced flag
set to false.
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_print_dv_timings() didn't log the interlaced format correctly. The timings
for the bottom field weren't logged and the fields per second value was half of what
it should have been.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, in gtf hblank calculations, the rounding is used twice,
one at intermediate division and one at final state where hblank
is rounded to nearest multiple of twice cell granularity. This
error got introduced in 'commit d7ed5a3dda ("[media]
v4l2-dv-timings: fix rounding in hblank and hsync calculation"),
where it missed combining the rounding step. Correcting the same
in this patch.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Log the alternate gamma state and the HDMI colorspace that the adv
device detected.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logging of the saturator status was wrong due to an incorrect
condition.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for logging the detected InfoFrames for the adv76xx. Helps in
debugging what is actually received on the HDMI link.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7511 sets up InfoFrames that are used when transmitting video.
Log the contents of those InfoFrames so it is possible to see exactly what
the transmitter is sending.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently this driver mixes u8/u32 and uint8_t/uint32_t. Standardize on
u8/u32.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently this driver mixes u8/u16 and uint8_t/uint16_t. Standardize on
u8/u16.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the missing VIDIOC_CREATE_BUFS and VIDIOC_PREPARE_BUF
ioctls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was never added for some reason, so add it now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must return -ENODEV error on case probe() fails to detect chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must return -ENODEV error on case probe() fails to detect chip.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to set some error codes here.
Fixes: f01919e8f5 ('[media] m88ds3103: add I2C client binding')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If userspace passed the invalid buffer type 0 to the kernel, then the
kernel log would show 'type=(null)' since there was no string defined
for type 0. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This field was never cleared by the kernel making future extensions
hard to implement. Clear it now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently the colors for the Y16 and Y16_BE pixelformats are in the range
0x0000-0xff00. So pure white (0xffff) is never created.
Improve this by making white really white. For other colors the lsb remains 0
so vivid can be used to detect endian problems.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This has been on my TODO list for some time now: the control that enables the video
loopback was part of the controls of the video output device instead of the video
capture device. In practice this was quite annoying since you expect it at the capture
side since that's where you want to make the decision whether to use the TPG or looped
video.
This patch moves the control from the output to the capture side.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tuner FMD1216ME_MK3 suffers the same problem as FMD1216MEX_MK3,
as described in saa7134-cards.c (disabled IF, enabled DVB-T). The
card does work under MS Windows, after soft reboot into Linux it
continues to work, only then tda9887 is loaded as well.
I copied the relevant code from the BEHOLD_H6 section to MD7134.
The CTX946 TV card doesn't detect a signal after cold boot, seems
Signed-off-by: Juergen Gier <juergen.gier@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current v4l2_of_parse_parallel_bus function attempts to parse the
DT properties for the parallel bus as well as BT656 bus.
If the pclk-sample property is defined for the BT656 bus, it is still
marked as a parallel bus.
Fix this by parsing the pclk after the bus_type is selected.
Only when hsync or vsync properties are specified, the bus_type should
be set to V4L2_MBUS_PARALLEL.
Signed-off-by: Nikhil Devshatwar <nikhil.nd@ti.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Load PCTV 460e tda10071 demod and a8293 SEC using I2C client bindings.
Remove old unused tda10071 config struct. We are using I2C platform
data now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 84cb7be43c broke vivid-tpg
(uninitialized variable p).
This patch takes a different approach: four different functions are
created, one for each PRINTSTR version.
In order to avoid the 'the frame size of 1308 bytes is larger than 1024
bytes' warning I had to mark those functions with 'noinline'. For
whatever reason gcc seems to inline this aggressively and it is doing
weird things with the stack.
I tried to read the assembly code, but I couldn't see what exactly it
was doing on the stack.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify cobalt_g/try_fmt_vid_cap by not setting the colorspace fields in
pix again (since v4l2_fill_pix_format does that already), and by using
v4l2_fill_mbus_format in cobalt_s_fmt_vid_out which allows the get_fmt
call to be dropped as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the transfer function to the cobalt driver: make sure it is
passed on to/retrieved from the sub-device correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precalculate all the colorspace/transfer function combinations in order
to easily generate the correct colors.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the transfer function: create a new control for it,
and support it for both capture and output sides.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this part of the format check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Still preliminary, but the information is at least there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the past the transfer function was implied by the colorspace. However,
it is an independent entity in its own right. Add support for explicitly
choosing the transfer function.
This change will allow us to represent linear RGB (as is used by openGL), and
it will make it easier to work with decoded video material since most codecs
store the transfer function as a separate property as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's a dead code on usbvision that makes it harder to read
and produces a smatch warning about bad identation.
Improve the code readability and add a FIXME to warn about
the current hack there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch reports a warning:
drivers/media/usb/tm6000/tm6000-video.c:646 tm6000_prepare_isoc() error: we previously assumed 'dev->urb_buffer' could be null (see line 624)
This is not really a problem, but it actually shows that the check
if urb_buffer is NULL is being done twice: at the if and at
tm6000_alloc_urb_buffers().
We don't need to do it twice. So, remove the extra check. The code
become cleaner, and, as a collateral effect, smatch becomes happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch currently produces two warnings:
drivers/media/pci/ivtv/ivtv-fileops.c:901 ivtv_v4l2_close() warn: suspicious bitop condition
drivers/media/pci/ivtv/ivtv-fileops.c:1026 ivtv_open() warn: suspicious bitop condition
Those are false positives, but it is not hard to get rid of them by
using a different way to evaluate the macro, splitting the logical
boolean evaluation from the bitmap one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/bt8xx/dst_ca.c:323 ca_get_message() warn: this array is probably non-NULL. 'p_ca_message->msg'
drivers/media/pci/bt8xx/dst_ca.c:498 ca_send_message() warn: this array is probably non-NULL. 'p_ca_message->msg'
Those two checks are needless/useless, as the ca_msg struct is
declared as:
typedef struct ca_msg {
unsigned int index;
unsigned int type;
unsigned int length;
unsigned char msg[256];
} ca_msg_t;
So, if the p_ca_message pointer is not null, msg will also be
not null.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/dib0090.c:1710 dib0090_dc_offset_calibration() warn: missing break? reassigning '*tune_state'
There's no need to change tune_state there, as the fall though code
will change it again to another state. So, simplify it by
removing the dead code.
While here, fix a typo:
Sart => Start
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch reports two issues:
drivers/media/platform/sh_vou.c:670 vou_adjust_output() error: buffer overflow 'vou_scale_v_num' 3 <= 4
drivers/media/platform/sh_vou.c:670 vou_adjust_output() error: buffer overflow 'vou_scale_v_den' 3 <= 4
It seems that there's actually a bug here: the same var (idx) is used
as an index for vertical and horizontal scaling arrays. However,
there are 4 elements on the h arrays, and only 3 at the v ones.
On the first loop, it may select index 4 for the horizontal array.
In this case, if the second loop fails to select an index, the
code would keep using 4 for the vertical array, with is past of
the array sizes.
The intent here seems to use index 0, if the scale is not found.
So, use a separate var for the vertical index.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/dvb-frontends/drxk_hard.c:3277 dvbt_sc_command() warn: missing break? reassigning 'status'
This is basically because the error handling logic there was crappy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the following compilation warnings:
drivers/media/platform/vivid/vivid-tpg.c: In function 'tpg_gen_text':
drivers/media/platform/vivid/vivid-tpg.c:1562:1: warning: the frame size of 1308 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
This seems to be due to some bad optimization done by gcc.
Moving the for() loop to happen inside the macro solves the
issue.
While here, fix CodingStyle at the switch().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Commits a0f10c131c and
6c9fe76536 ("media: s5p-mfc: fix broken
pointer cast on 64bit arch") fixed issue with lossy cast on 64-bit
architectures. However it also removed __iomem attribute from that cast.
This leads to sparse warnings. This patch fixes those warnings by adding
__iomem cast in case of v6+ code version and replacing readl/writel by
simple u32 load/store operations in case of v5 code (which is called on
system memory allocated by dma_alloc_coherent() instead of io registers).
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
this patch makes use of helper function v4l2_get_timestamp()
to set the timestamp of vb2 buffer.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need own I2C locking because of tuner I2C adapter/repeater.
Firmware command is executed using I2C send + reply message. Default
I2C adapter locking protects only single I2C operation, not whole
send + reply sequence as needed. Due to that, it was possible tuner
I2C message interrupts firmware command sequence.
Reported-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After adding virtio-gpu I get this funky kconfig dependency loop.
scripts/kconfig/conf --oldconfig Kconfig
drivers/video/fbdev/Kconfig:5:error: recursive dependency detected!
drivers/video/fbdev/Kconfig:5: symbol FB is selected by DRM_KMS_FB_HELPER
drivers/gpu/drm/Kconfig:34: symbol DRM_KMS_FB_HELPER is selected by DRM_VIRTIO_GPU
drivers/gpu/drm/virtio/Kconfig:1: symbol DRM_VIRTIO_GPU depends on VIRTIO
drivers/virtio/Kconfig:1: symbol VIRTIO is selected by REMOTEPROC
drivers/remoteproc/Kconfig:4: symbol REMOTEPROC is selected by OMAP_REMOTEPROC
drivers/remoteproc/Kconfig:12: symbol OMAP_REMOTEPROC depends on OMAP_IOMMU
drivers/iommu/Kconfig:141: symbol OMAP_IOMMU is selected by VIDEO_OMAP3
drivers/media/platform/Kconfig:96: symbol VIDEO_OMAP3 depends on VIDEO_V4L2
drivers/media/v4l2-core/Kconfig:6: symbol VIDEO_V4L2 depends on I2C
drivers/i2c/Kconfig:7: symbol I2C is selected by FB_DDC
drivers/video/fbdev/Kconfig:59: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/fbdev/Kconfig:374: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/fbdev/Kconfig:362: symbol FB_CYBER2000 depends on FB
Making VIDEO_OMAP3 depend on OMAP_IOMMU instead of selecting it breaks the
loop, which looks like the best way to handle it to me. Updated OMAP_IOMMU
help text accordingly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The UVC_DEV_DISCONNECTED flag is set when the USB device is
disconnected, and checked in the open() handler to refuse opening a
device that has been disconnected.
This is inherently racy, but the race condition is taken care of in the
V4L2 core, which also fails open() calls when the V4L2 device node has
been unregistered. As the uvcvideo USB disconnect handler unregisters
all its video device nodes, the UVC_DEV_DISCONNECTED flag doesn't serve
any purpose anymore and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "TOSHIBA Web Camera - 5M" Chicony device (04f2:b50b) seems to
compute the bandwidth on 16 bits and erroneously sign-extend it to
32 bits, resulting in a huge bandwidth value. Detect and fix that
condition by setting the 16 MSBs to 0 when they're all equal to 1.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that videobuf2-vmalloc supports exporting buffers, add support for
the DMABUF exporter role by plugging in the videobuf2 ioctl helper.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is AF9035 + MxL5007T.
Driver reports:
prechip_version=00 chip_version=03 chip_type=3802
Not sure if that USB ID is reserved only for HP brand or if it is
common, but the stick I have is branded as HP part no. 580715-001
rmn A867.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement I2C client device binding.
Wrap media attach to driver I2C probe.
Add wrapper from m88ds3103_attach() to m88ds3103_probe() via driver
core in order to provide proper I2C client for legacy media attach
binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use jiffies to set timeout for DiSEqC TX ready polling. Using jiffies
is more elegant solution than looping N times with sleep.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement DVBv5 BER statistics.
Wrap legacy DVBv3 BER to DVBv5 BER.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do not return error from get_frontend() when status is queried, but
the frontend didn't lock yet. The proper behavior is to only update the
cache after having a lock.
[mchehab@osg.samsung.com: fix the patch description]
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Autogain algorithm is very simple, if average luminance is low - increase gain,
if it's high - decrease gain. Gain granularity is low enough for this algo to
stabilize quickly.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This cam seems to return different values on long commands, so make status check
in sn9c2028_long_command() more tolerant. Anyway, read value isn't used anywhere
later.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
U8 and U16LE format human readable names were translated with string
containing emulated word. These strings were taken from msi2500 driver,
where those formats were emulated (after module parameter is set). But
on API correct names should be used, without any special case notes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use these defines instead of hardcoding this in any driver that needs it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The log_status ioctl should report if the audio input has mode Bilingual. However, the
check against the itv->dualwatch_stereo_mode is completely wrong and is a left-over from
the distant past. Not only is the bitmask obviously wrong, the test itself is broken too
since itv->dualwatch_stereo_mode is no longer a bitmask at all.
Fix this code properly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for V4L2_PIX_FMT_Y16_BE, a 16 bit big endian greyscale format.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
16 bit greyscale format, structured in Big Endian. Such a format can be
converted into a PMN image just by adding a header.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dma_map_sg returns the number of areas mapped by the hardware,
which could be different than the areas given as an input.
The output must be saved to nent.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dma_map_sg returns the number of areas mapped by the hardware,
which could be different than the areas given as an input.
The output must be saved to nent.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When sg_alloc_table_from_pages() does not fail it returns a sg_table
structure with nents and nents_orig initialized to the same value.
dma_map_sg returns the number of areas mapped by the hardware,
which could be different than the areas given as an input.
The output must be saved to nent.
The output of dma_map, should be used to transverse the scatter list.
dma_unmap_sg needs the value passed to dma_map_sg (nents_orig).
sg_free_tables uses also orig_nent.
This patch fix the file to follow this paradigm.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7604 driver depends on GPIOLIB, and therefore cobalt depends
on it as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/cx24120.c:837:6: warning: symbol 'cx24120_calculate_ber_window' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/pci/cobalt/cobalt-flash.c:101:5: warning: symbol 'cobalt_flash_probe' was not declared. Should it be static?
drivers/media/pci/cobalt/cobalt-flash.c:126:6: warning: symbol 'cobalt_flash_remove' was not declared. Should it be static?
drivers/media/pci/cobalt/cobalt-cpld.c:101:6: warning: symbol 'cobalt_cpld_status' was not declared. Should it be static?
drivers/media/pci/cobalt/cobalt-cpld.c:240:6: warning: symbol 'cobalt_cpld_set_freq' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/pci/cobalt/cobalt-flash.c:39:36: warning: incorrect type in initializer (different address spaces)
drivers/media/pci/cobalt/cobalt-flash.c:54:36: warning: incorrect type in initializer (different address spaces)
drivers/media/pci/cobalt/cobalt-flash.c:63:36: warning: incorrect type in initializer (different address spaces)
drivers/media/pci/cobalt/cobalt-flash.c:82:36: warning: incorrect type in initializer (different address spaces)
drivers/media/pci/cobalt/cobalt-flash.c:107:19: warning: incorrect type in assignment (different address spaces)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/tuners/e4000.c:287:3: warning: this decimal constant is unsigned only in ISO C90
.rangehigh = 2208000000L,
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixes these warnings:
drivers/media/pci/cobalt/cobalt-omnitek.c: In function 'omni_sg_dma_start':
drivers/media/pci/cobalt/cobalt-omnitek.c:112:28: warning: right shift count >= width of type [-Wshift-count-overflow]
iowrite32((u32)(desc->bus >> 32), DESCRIPTOR(s->dma_channel) + 4);
^
drivers/media/pci/cobalt/cobalt-omnitek.c: In function 'descriptor_list_create':
drivers/media/pci/cobalt/cobalt-omnitek.c:222:28: warning: right shift count >= width of type [-Wshift-count-overflow]
d->next_h = (u32)(next >> 32);
^
drivers/media/pci/cobalt/cobalt-omnitek.c:268:32: warning: right shift count >= width of type [-Wshift-count-overflow]
d->next_h = (u32)(desc->bus >> 32);
^
drivers/media/pci/cobalt/cobalt-omnitek.c:275:27: warning: right shift count >= width of type [-Wshift-count-overflow]
d->next_h = (u32)(next >> 32);
^
drivers/media/pci/cobalt/cobalt-omnitek.c: In function 'descriptor_list_chain':
drivers/media/pci/cobalt/cobalt-omnitek.c:293:31: warning: right shift count >= width of type [-Wshift-count-overflow]
d->next_h = (u32)(next->bus >> 32);
^
drivers/media/pci/cobalt/cobalt-omnitek.c: In function 'descriptor_list_loopback':
drivers/media/pci/cobalt/cobalt-omnitek.c:332:30: warning: right shift count >= width of type [-Wshift-count-overflow]
d->next_h = (u32)(desc->bus >> 32);
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The interrupt bit assignments use for the adv7511 were off by one.
This means that the current scheme (bit << (4 * stream_index)) can
no longer be used.
Fix this by precalculating and storing the correct masks in the
cobalt_stream struct.
This wasn't noticed before because the adv7511 interrupts are very
rare. But for CEC support these interrupts are essential, so this made
me realize that it wasn't working correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ucblocks register is probably a counter and not a rate; assume
it is so and change the calculations as required.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the 0x0x prefix in integer constants.
In this case a padding 0 must also be inserted to make the constants
look like all the other 16 bits ones.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Frontend bandwidth calculation overflows on very high DVB-S/S2
symbol rates. Use mult_frac() macro in order to keep calculation
correct.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/tuners/e4000.c:287:32: warning: constant 2208000000 is so big it is long long
drivers/media/tuners/e4000.c:287:32: warning: decimal constant 2208000000 is between LONG_MAX and ULONG_MAX. For C99 that means long long, C90 compilers are very likely to produce unsigned long (and a warning) here
drivers/media/tuners/e4000.c:287:3: warning: this decimal constant is unsigned only in ISO C90
.rangehigh = 2208000000,
^
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement V4L2 subdevice tuner and core ops. After that this driver
is hybrid driver implementing both V4L2 and DVB ops.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* Rename device state from 's' to 'dev'.
* Move single include to driver private header.
* Change error handling type of each function to one I tend use
nowadays.
* Remove dummy register write from init. Even Windows driver does this
multiple times remove it as I have never seen any I2C errors.
* Define I2C client pointer for each function and use it.
* Do not clean tuner ops during driver remove - not needed.
* Disable sysfs device bind / unbind. We are not allowed manually
bind / unbind device from the driver currently.
* Rename some other variables.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Update synthesizer calculation to model I prefer nowadays. It is
mostly just renaming some variables to ones I think are most standard.
Also add 'schematic' of synthesizer following my current understanding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This code works fine but static checkers complain. The test_bit()
function takes the bit number and not a mask. Then the other issue is
that we were using USB_STATE_URB_BUF which is BIT(0) instead of URB_BUF.
Also we were open coding that instead of using the test/clear/set_bit()
functions.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cobalt device is a PCIe card with 4 HDMI inputs (adv7604) and a
connector that can be used to hook up an adv7511 transmitter or an
adv7842 receiver daughterboard.
This device is used within Cisco but is sadly not available outside
of Cisco. Nevertheless it is a very interesting driver that can serve
as an example of how to support HDMI hardware and how to use the popular
adv devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This makes it easier for the bridge driver to just passthrough such
events to the corresponding device node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
vb2_buffer_done() already allows STATE_QUEUED, but currently only when not
streaming. It is useful to allow it while streaming as well, as this makes
it possible for drivers to requeue buffers while waiting for a stable
video signal.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the dummy video format operations by pad format operations that
configure the output format.
Copied from the adv7604 driver.
Note: while arch/blackfin/mach-bf609/boards/ezkit.c uses adv7842_platform_data
this source has not been updated because it is broken since the very
beginning. It depends on a struct adv7842_output_format that does not
exist.
And besides that gcc has no support for bf609 so nobody can compile it
except by installing a toolchain from ADI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These state vars are used for more than just ber calculation, also
fix typo.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
BER & UCB aren't available unless we're locked; don't update dvbv5
stats when not locked and mark these counters as unavailable.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBv3 is a legacy API. Drivers should use DVBv5, in order to support
modern applications. So, implement UCB using dvbv5.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of reading BER again for DVBv3 call, use the value from the cache.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBv3 is a legacy API. Drivers should use DVBv5, in order to support
modern applications. So, implement BER using dvbv5.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use const on the static data, as gcc may optimize better the
code. Also, would prevent that some code would override the
data there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
As reported by smatch:
drivers/media/dvb-frontends/cx24120.c: In function 'cx24120_message_send':
drivers/media/dvb-frontends/cx24120.c:368:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret, ficus;
^
The values written by cx24120 are never checked. So, remove the
check here too. That's said, the best would be to do the reverse,
but globally: to properly handle the error codes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Add in all the likely values for setting fec on tuning. Some values
yet to be tested but very likely to be correct.
In the very unlikely event that these are wrong tuning with
FEC_AUTO will still work.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If set, all the other drivers reset no_base_addr on failure to
attach - git commit for this being added to some of them seems to
be eccd15aad7
This driver has been floating around outside the mainline for so
long it hasn't had this fix, so add it in.
Whilst here tidy surrounding code to fix style issues.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove reg1 by refactoring for loops
Change ret into an int as it's only used for return values now,
and remove reset_result by using ret instead.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use reg instead of ret for all calls to readreg, remove ret_EA
as it doesn't need to be a separate var anymore.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Probably a remnant of this driver being reverse engineered,
cx24120_init assigned ret on each call to writereg - they're not
used for anything so remove them to clear up the codebase.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove __func__ from calls to dev_dbg as dynamic debug can add in
the function name anyway.
Remove debug call in dvbv3 read_signal_strength as userspace has
this value anyway.
Reword some strings to make them simpler / more obvious.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Better to report CNR via DVBv5 stats, as scale can be used.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous version of this driver had a memset before every call
to cmd. This meant the default value of cmd.arg[1] was zero unless
burst is set. Make sure it remains zero.
Also fe_sec_mini_cmd_t is an enum, so test against it.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Algorithm copied from cx24117.c - it seems to work. Showing 95% on
a signal I know to be somewhere around 74dBuV.
[mchehab@osg.samsung.net: merged two patches, to avoid breaking compilation]
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes DVBv3 signal strength to read from the cache by
moving the signal strength reading routine into get_stat, and
reducing read_signal_strength to just returning the cached value.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
get_frontend was making a call to read_status, which is being
called periodically anyway. Have read_status store fe_status in
the state struct instead and use that within get_frontend.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previous patch added in collection, this patch enables them by
signalling they are available.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new get_stats function, called from read_status, for
collecting DVBv5 stats into the frontend cache. Only signal
strength for now, can add others later.
Not currently marked as available, future patch will enable.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change calculate_vco function to send_vco to tidy up cx24120_init
function.
xxyyzz variable is remnants of a manual div & remainder codepath
to perform a u64 rounded div; replace with kernel macro
DIV_ROUND_CLOSEST_ULL
Hex values provided to the message are mainly variables calculated
within this function, replace with these to remove hardcoding.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
msg.len has been ++'d so msg.len is one too many.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds in a missing command to cx24120_check_cmd. This part
of the old reverse engineered driver was quite hard to follow - it's
presumed the compiler did some neat optimisation that wasn't easy to
decode. This command was checked for in that version but not copied
across to the new switch statement.
For reference, old reverse engineered code:
xxzz = cmd->id - 0x11; // look for specific message id
if ( xxzz <= 0x13 ) {
msg_cmd_mask = 1 << xxzz;
//0x0F8021 // if cmd_id 17 or 22 or 33-36, 42, 47, 57-61 etc. disable mpeg output
if ( msg_cmd_mask & 0x0F8021 ) { // 000011111000000000100001b
cx24120_msg_mpeg_output_global_config(state, 0);
msleep(100);
state->dvb_s2_mode &= 0xFD; // reset mpeg out enable flag
}
}
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch removes the requirement of waiting for tune in
set_frontend by moving the clock set call into read_status
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes DVB-S/DVB-S2 to the more commonly used
DVB-S/S2 in the description for DVB_CX24120
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patches fixes all checkpatch-errors.
Even the ones created --strict.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro pointed out some coding style issues in his review.
This patch fixes them.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some i2c-hosts are quite limited regarding maximum
i2c-burst-write-sizes. This patch makes the previously
hardcoded field configurable by users of the driver.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes printk-related checkpatch warnings. All printks
have been converted to pr_warn or pr_info or pr_err.
Signed-off-by: Patrick.Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the Technisat Skystar S2 - this
has been tried before but the cx24120 driver was a bit out of shape
and it didn't got any further:
https://patchwork.linuxtv.org/patch/10575/
It is an old card, but currently being sold off for next to nothing,
so it's proving quite popular of late. Noticing it's quite similar
to the cx24116 and cx24117 I've rewritten the driver in a similar way.
There were a few registers and commands from those drivers
missing from this one I've tested out and found they do something so
they've been added in to speed up tuning and to make get_frontend
return something useful.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Patrick.Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though the rcar-vin driver tells userspace that it will give a monotonic
timestamp, it is actually using gettimeofday. Replace this with a proper
monotonic timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2 drivers should use MONOTONIC timestamps instead of gettimeofday, which is
affected by daylight savings time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The intermediate calculation in the expression for hblank can exceed
32 bit signed range. This overflow can lead to negative values for
hblank. Typecasting intermediate variable to higher precision.
Cc: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
[hans.verkuil@cisco.com: made the denominator u32, since that's what div_u64 expects]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove code duplication by merging two cases in a switch.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for V4L2_PIX_FMT_Y16, a 16 bit greyscale format.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add initial support for fc2580 tuner based devices.
Tuner is controlled via V4L2 subdevice API.
Passes v4l2-compliance tests.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement V4L2 subdevice for bandwidth and frequency controls of
SDR usage. That driver now implements both DVB frontend and V4L2
subdevice. Driver itself is I2C driver. Lets see how it works.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate low-pass filter control word dynamically from given radio
channel bandwidth.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rtl2832 demod driver has support for FC2580 tuner config, no need to
abuse FC0012 settings anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use div_u64() to simplify and remove home made divides.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We are using I2C client binding now, so remove old media attach.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change tua9001 driver from media binding to I2C client binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change tua9001 driver from media binding to I2C client binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Driver supports multiple chipset versions. Devices are ordered to
ID table per used chipset type. "ITE 9303 Generic" device uses IT9303
chipset and was added mistakenly between IT9135 IDs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace home made register access routines with regmap.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename driver state from priv to dev.
Remove legacy i2c-gate control.
Use I2C client for proper dev_() logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate PLL dividers slightly differently, most likely it is now
correct. Move some register values to innitab. Use jiffies to poll
filter lock. Fix logging.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All users are using driver via I2C client binding so lets remove
unneeded media binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change fc2580 driver from media binding to I2C client binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change fc2580 driver from media binding to I2C client binding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For every frontend entry, we need to add the adapter's size. There
are already two patches fixing it. So, it doesn't seem trivial to
keep it there at the right place.
Also, currently, the indentation is wrong on all places.
So, it seems that keeping it right is not too trivial.
Better to use a macro that would do it for us, at least while
this is not converted to dvb-usb-v2.
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enhances driver to use an MSI interrupt when available.
Adds the module option 'enable_msi' (type bool) which by default is
enabled. Can be set to 'N' to disable.
Fixes (or can reduce the occurrence of) a crash which is most commonly
reported when both digital tuners of the saa7164 chip is in use. A
reported example can be found here:
http://permalink.gmane.org/gmane.linux.drivers.video-input-infrastructure/83948
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The same code is executed if ret is true or false, so this test can
be removed.
Fix Coverity CID 1268782.
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert
scancodes from user space to pulse/space format understood by the
underlying hardware.
Converted samples are then written to the wakeup fifo along with other
necessary configuration to enable wake up functionality.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the s_wakeup_filter callback to the rc-loopback driver, which instead of
setting the filter just feeds the scancode back through the input device
so that it can be verified.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true to make the
allowed wakeup protocols the same as the set of raw IR encoders.
As well as updating the sysfs interface to know which wakeup protocols
are allowed for encode_wakeup drivers, also ensure that the IR
decoders/encoders are loaded when an encode_wakeup driver is registered.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the capability to encode RC-6 and RC-6A scancodes as raw events.
The protocol is chosen based on the specified protocol mask, and
whether all the required bits are set in the scancode mask, and none of
the unused bits are set in the scancode data.
The Manchester modulation helper is used several times with various
timings so that RC-6 header preamble, the header, header trailing bit
and the data itself can be modulated correctly.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the capability to encode RC-5, RC-5X and RC-5-SZ scancodes as raw
events. The protocol is chosen based on the specified protocol mask,
and whether all the required bits are set in the scancode mask, and
none of the unused bits are set in the scancode data. For example a
scancode filter with bit 16 set in both data and mask is unambiguously
RC-5X.
The Manchester modulation helper is used, and for RC-5X it is used twice
with two sets of timings, the first with a short trailer space for the
space in the middle, and the second with no leader so that it can
continue the space.
The encoding in RC-5-SZ first inserts a pulse and then simply utilizes
the generic Manchester encoder available in rc-core.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding a simple Manchester encoder to rc-core.
Manchester coding is used by at least RC-5 and RC-6 protocols and their
variants.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode filter to a form that is more suitable for
raw hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename state to dev.
Correct some indentations.
Remove FSF address.
Fix some style issues reported by checkpatch.pl.
Correct some style issues I liked.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Update synthesizer calculation to model I prefer nowadays. It is mostly
just renaming some variables, but also minor functionality change how
integer and fractional part are divided (using div_u64_rem()). Also, add
'schematic' of synthesizer following my current understanding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename state from s to dev. Rename some other things. Fix indentations.
Disable driver unbind via sysfs.
indentation prevent unload
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Update synthesizer calculation to model I prefer nowadays. It is mostly
just renaming some variables, but also minor functionality change how
integer and fractional part are divided (using div_u64_rem()). Also, add
'schematic' of synthesizer following my current understanding.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix an oops during device initialization by correctly setting size_of_priv
instead of leaving it 0.
The regression was introduced by 8abe4a0a3f ("[media] dib7000:
export just one symbol") and only fixed for one type of dib0700 based
devices in 9e334c7564 ("[media] Fix regression in some dib0700
based devices").
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=92301
Fixes: 8abe4a0a3f ("[media] dib7000: export just one symbol")
Cc: stable@vger.kernel.org # for version 3.17+
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the streaming_ctrl is called to enable TS before demod has locked
the TS will be empty. Copied the solution from the dvbsky driver for the
TechnoTrend S2-4600 device: when the state changes from unlock to
lock, call su3000_streaming_ctrl again.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While reading the MAC address for SU3000-based devices the system was
printing excessive debug information in the logs:
Output before the patch:
[ 1515.780692] bc 00 00 00 00 00
[ 1515.781440] bc ea 00 00 00 00
[ 1515.782251] bc ea 2b 00 00 00
[ 1515.783094] bc ea 2b 46 00 00
[ 1515.783816] bc ea 2b 46 12 00
[ 1515.784565] bc ea 2b 46 12 92
[ 1515.784571] dvb-usb: MAC address: bc:ea:2b:46:12:92
Output after the patch:
[ 3803.495706] dvb-usb: MAC address: bc:ea:2b:46:12:92
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
SRVM_MAX_PID_FILTERS was defined in 2 sms_tx_stats structures
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the 0x0x prefix in integer constants.
In this case a padding 0 must also be inserted to make the constants
look like all the other 16 bits ones.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
My static checker warns that the name of the port can be 15 characters
when you consider the NUL terminator and that's one more than the 14
characters in name[]. Maybe it's an off-by-one?
It's unlikely that we hit the limit and even if we do the overflow will
only affect one of the two bytes of padding so it's harmless. Still
let's fix it and also change the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/st_rc.c:270: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/st_rc.c:271: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' and
'rx_base' definitions accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/ir-hix5hd2.c:221: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/ir-hix5hd2.c:222: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' definition
accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In a rarely hit randconfig case, the r820t tuner driver can
get built when CONFIG_BITREVERSE is not selected by any
other driver, resulting in this error:
drivers/built-in.o: In function `r820t_read.constprop.3':
:(.text+0xa0594): undefined reference to `byte_rev_table'
For consistency, this adds the 'select BITREVERSE' that
all other similar drivers have.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without i2c, we can get a build error:
drivers/media/platform/exynos4-is/fimc-is-i2c.c: In function 'fimc_is_i2c_probe':
drivers/media/platform/exynos4-is/fimc-is-i2c.c:58:8: error: implicit declaration of function 'i2c_add_adapter' [-Werror=implicit-function-declaration]
The dependency already exists for exynos-fimc-lite and s5p-fimc,
but is missing for exynos4-fimc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several lines touched by the pr_foo refactoring patches are not
following the Linux Coding style.
While we won't be fixing the style globally at the driver, we should,
at least, fix on the lines we touched.
Basically, this patch add (or remove) whitespaces and blank lines
where needed.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The debug macros are not properly defined, as they generate warnings
like:
ERROR: Macros with complex values should be enclosed in parentheses
+#define core_dbg(fmt, arg...) if (core_debug) \
+ printk(KERN_DEBUG pr_fmt("core: " fmt), ## arg)
Use do { } while (0) for those macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of implement its own hexdump logic, use the printk
format, and convert to use pr_info().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename the macros to input_dbg() and ir_dbg(), using pr_fmt()
on both, to be coherent with the other debug macro changes.
The ir_dbg() also prints the IR name.
I'm not sure if it is a good idea to keep both macros here,
but merging them would require tests on different flavors of
saaa7134-based boards.
So, for now, let's keep both.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rename the macro to vbi_dbg()/video_dbg() and use pr_fmt(),
to be coherent with the other debug macro changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
instead of using dev->name, let's use pr_fmt() like on the
other parts of saa7134. Also, rename the debug macro to
ts_dbg() to match the namespace for the debug macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Converting debug prints to use pr_foo() is not trivial, as the
result will be a way worse than what's provided here, due to the
pieces of the code that prints the I2C transfers. Those use a
lot pr_cont(), and, depending on using either level 1 or 2,
a different set of macros are selected.
So, let's replace d1printk() and d2printk() macros by i2c_dbg()
and i2c_count() adding a debug level there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On media drivers, debugging messages should be grouped into
categories, as this makes easier to debug the driver.
In the case of saa7134, the core has 2 debug categories, one
for IRQ, and another one for the core itself. The IRQ have
actually 2 levels of debug.
So, instead of using pr_dbg(), where everything would be in
the same box, let's define two macros that use pr_fmt(),
one for the core, and another one for irq.
With that, we can replace the remaining printk() occurrences
at the core to use either core_dbg() or irq_dbg(), depending
on the group of debug macros that need to be enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On a few places, mostly during board detection, some printk()
macros were called without especifying any message level.
Those are actually warnings. So, use pr_warn() for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As this module doesn't use any debug level, it is easy to
just replace all debug printks by pr_debug().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As this module doesn't use any debug level, it is easy to
just replace all debug printks by pr_debug().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On saa7134-alsa, there is just one printk macro that use a
different debug level.
It should be easy to enable/disable this one using dynamic_printk,
if one need to individually control it.
So, this module can easily use pr_debug() instead of using its
own macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On a few places, the search expression used on the script that
replaced pr_info/pr_warn didn't match, because the string were
on the next line.
It is best to manually edit those lines, and re-indent the
paragraphs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replaces all occurrences of printk with KERN_INFO, KERN_WARNING
and KERN_ERR to pr_info/pr_warning, pr_err, using this small
shell script:
for i in drivers/media/pci/saa7134/*.[ch]; do sed s,'printk(KERN_INFO ','pr_info(',g <$i >a && mv a $i; done
for i in drivers/media/pci/saa7134/*.[ch]; do sed s,'printk(KERN_ERR ','pr_err(',g <$i >a && mv a $i; done
for i in drivers/media/pci/saa7134/*.[ch]; do sed s,'printk(KERN_WARNING ','pr_warn(',g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a pr_fmt macro, and move saa7134.h header to the beginning,
to avoid warnings when using the pr_foo macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
commit af3a4a9bbe ("[media] dib0700: NEC scancode cleanup") cleaned
up the NEC scancode logic but overlooked the RC5 case.
This patch brings the RC5 case in line with the NEC code and makes
the struct self-documenting.
Signed-off-by: David Härdeman <david@hardeman.nu>
Reported-by: David Cimbůrek <david.cimburek@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver does not use any PCI IDs, don't include
the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case of error, the function platform_device_register_data() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GoTView MasterHD 3 is a DVB-T2/C USB 2.0 tuner.
It's based on the following components:
- USB bridge: RTL2832P (contains also DVB-T demodulator)
- Demodulator: Si2168-A30
- Tuner: Si2148-A20
The demodulator and the tuner will need firmwares. The Si2148 uses Si2158
firmware. Antti has the firmwares available for download:
http://palosaari.fi/linux/v4l-dvb/firmware/
Do note that for DVB-T either of the demodulators can be used. DVB-C and
DVB-T2 are only supported by the Si2168 demodulator. The driver will
register 2 frontends for the same adapter. Frontend 0 will be the RTL2832
demodulator and frontend 1 will be the Si2168 demodulator. The same
tuner is used for both.
As a consequence of the above, it's recommended to use application that
does implement proper DVBv5 support.
For some reason, the old I2C write method sporadically fails. Thus the
need for an option to only use the new I2C write method supported by the
RTL2832.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for I2C read operation without a preceeding write.
While here, change the error code to EOPNOTSUPP in case an
unsupported I2C operation is attempted.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The chips supported by the si2157 driver have two IF outputs (either
pins 12+13 or pins 9+11). Instead of hardcoding the output to be used
add an option to choose which output shall be used.
As this patch changes the default behaviour, the IF interface is
specified in each driver currently using si2157 driver. This is to
keep bisectability.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return error from si2168_cmd_execute in case the demodulator returns an
error.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change the dvbsky driver to support gapped clock instead of the current
hack.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a parameter in si2168_config to support gapped clock. This might be
necessary on some devices with higher bitrates.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove dead code, make goto label names more expressive and add a label
in order to call mantis_dvb_exit if mantis_uart_init fails.
Also make sure that mantis_pci_exit is called if we fail the
mantis_stream_control call and that we call mantis_i2c_exit if
mantis_get_mac fails.
[mchehab@osg.samsung.com: fix merge conflict]
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TeVii S482 is a PCIe device with two tuners that actually contains two
USB devices. The devices are visible in the lsusb printout.
Bus 006 Device 002: ID 9022:d483 TeVii Technology Ltd.
Bus 007 Device 002: ID 9022:d484 TeVii Technology Ltd.
The device itself works exactly with the same settings as TechnoTrend
TT-connect S2-4600. Firmware for DS3103 demodulator is required:
http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
This patch should be applied on top of the TT S2-4600 patch:
https://patchwork.linuxtv.org/patch/28818/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RGB444 format swapped the red and blue components, fix this.
Rather than making a new BGR444 format (as I proposed initially), Jon prefers
to just fix this and return the colors in the right order. I think that makes
sense in this case.
Since the RGB444 pixel format is deprecated due to the ambiguous specification
of the alpha component we use the XRGB444 pixel format instead (specified as having
no alpha channel).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of parsing the link-frequencies property in the driver, let
v4l2_of_alloc_parse_endpoint() do it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the last buffer flag causes the videobuf2 core to return -EPIPE from
DQBUF calls on the capture queue after the last buffer is dequeued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Setting the last buffer flag causes the videobuf2 core to return -EPIPE from
DQBUF calls on the capture queue after the last buffer is dequeued.
This patch also fixes the EOS event to conform to the specification. It now is
sent right after the last buffer has been decoded instead of when the last
buffer is dequeued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the last buffer was dequeued from a capture queue, let poll return
immediately and let DQBUF return -EPIPE to signal there will no more
buffers to dequeue until STREAMOFF.
The driver signals the last buffer by setting the V4L2_BUF_FLAG_LAST.
To reenable dequeuing on the capture queue, the driver must explicitly
call vb2_clear_last_buffer_queued. The last buffer queued flag is
cleared automatically during STREAMOFF.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
[k.debski@samsung.com: Fix misspelling in title (s/sp5/s5p/)]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVT9fTAAoJEHm+PkMAQRiGrbYH/276n6aKSORO0B6DrEnebu8Y
oxfJeacg90/N5aLx/B5GEplO24uTENaAfB342WkexziXdY+7P02J0Y36eSh5WiL2
qcL+gkiZVaApZIjVeO/y2ByL7nLprPeIsxl5gGLhI+qYYMaQ8gtzxC7sDLnNqjPS
w8WYQB7LdWeGFqcuvySEX2C6Q62aHpZWoSsV3LYdrfoDJz2lv1DJrOpRhqXPagl7
oX1c1CWQ4yWdFf9xm8vaiZw7EskxEnObQm7n7vWlZ0xAhXZ/3a7bPdc+fj2V+nve
xjZV/EhEL0u3ME86bVtcqbO3lgMjivyWHjQglCwG6keS+iIHkL0xMlQabkrFJhw=
=LGDf
-----END PGP SIGNATURE-----
Merge tag 'v4.1-rc3' into patchwork
Linux 4.1-rc3
* tag 'v4.1-rc3': (381 commits)
Linux 4.1-rc3
drm: Zero out invalid vblank timestamp in drm_update_vblank_count.
m32r: make flush_cpumask non-volatile.
mnt: Fix fs_fully_visible to verify the root directory is visible
path_openat(): fix double fput()
namei: d_is_negative() should be checked before ->d_seq validation
ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for exynos5250-snow
ARM: dts: Fix typo in trip point temperature for exynos5420/5440
ARM: dts: add 'rtc_src' clock to rtc node for exynos4412-odroid boards
ARM: dts: Make DP a consumer of DISP1 power domain on Exynos5420
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
drm/tegra: Don't use vblank_disable_immediate on incapable driver.
mmc: dw_mmc: dw_mci_get_cd check MMC_CAP_NONREMOVABLE
mmc: dw_mmc: init desc in dw_mci_idmac_init
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
drm/radeon: stop trying to suspend UVD sessions
drm/radeon: more strictly validate the UVD codec
...
The Media Controller DVB support is still an experimental feature,
as it is under heavy development. It is already said that it is
an experimental feature at the help, but let make it even clearer
and louder, as we may need to adjust some bits when we start using it
on embedded drivers.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Bellow is yelling. Ok, sometimes the code is yells a lot, but
but this is not the case there ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gmuD
-----END PGP SIGNATURE-----
Merge tag 'media/v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Three driver fixes:
- fix for omap4, fixing a regression due to a subsystem API that got
removed for 4.1 (commit efde234674);
- fix for one of the formats supported by Marvel ccic driver;
- fix rcar_vin driver that, when stopping abnormally, the driver
can't return from wait_for_completion"
* tag 'media/v4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] v4l: omap4iss: Replace outdated OMAP4 control pad API with syscon
[media] media: soc_camera: rcar_vin: Fix wait_for_completion
[media] marvell-ccic: fix Y'CbCr ordering
drivers/media/pci/saa7164/saa7164-dvb.c: In function ‘saa7164_dvb_register’:
drivers/media/pci/saa7164/saa7164-dvb.c:701:7: warning: ‘client_tuner’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (!client_tuner || !client_tuner->dev.driver)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to s_mbus_fmt in bridge drivers by calls to the
set_fmt pad op.
Remove the old try/s_mbus_fmt video ops since they are now no longer used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to try_mbus_fmt in bridge drivers by calls to the
set_fmt pad op.
[mchehab@osg.samsung.com: fix a merge conflict at mcam-core.c]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The try_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Since try_mbus_fmt and s_mbus_fmt both map to the set_fmt pad op (but
with a different 'which' argument), this patch will replace both
try_mbus_fmt and s_mbus_fmt by set_fmt.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The g_mbus_fmt video op is a duplicate of the pad op. Replace all uses
by the get_fmt pad op and remove the video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to the enum_mbus_fmt video op by the pad
enum_mbus_code op and remove the duplicate video op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kamil Debski <k.debski@samsung.com>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are a few lines longer than 80 cols for no good reason.
Fix them sooner than latter, making checkpatch.pl happy.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ensure that buffers are allocated from the DMA32 zone since this
device only handles 32 bit DMA addresses.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dt3155 code is now in good shape, so move it out of staging into
drivers/media/pci. Mark in MAINTAINERS that I'll do Odd Fixes for this
driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If i2c_add_adapter() fails, adap is not deallocated.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The REG_CTRL0 register was never written if this format was selected,
instead an error was logged and whatever was last set in that register
was used.
Surprisingly, that seems to work if YUYV was selected, but we should
program this register explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I cannot get this format to work, the colors keep coming out wrong.
Since this has never worked I just drop support for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These were calculated incorrectly for the planar formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Even though the format is Y'CbCr, the colorspace used by the sensor
is almost certainly SRGB. The sensor is also not generating JPEG data,
so it makes no sense to use V4L2_COLORSPACE_JPEG here.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver appeared to support the JPEG format when in reality
that was just dead code. Remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dma-vmalloc implementation didn't support planar formats, but with
a little bit of refactoring that is easy to fix.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If start_streaming fails or stop_streaming is called, then all queued
buffers need to be given back to vb2.
This prevents vb2 from calling WARN_ON when it detects that this is not
done correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- fill in timestamp
- fill in field
- start the sequence counter at 0, not 1
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add VB2_DMABUF and VIDIOC_EXPBUF support. Also add VB2_USERPTR support
for the vmalloc DMA mode which was missing for no good reason.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the final v4l2-compliance warning.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the V4L2 core locking system instead of rolling your own. Switch to
the vb2 fop and ioctl helpers to get rid of a lot of code. This also made
it easy to add VB2_READ to the DMA modes, since you get read() for free
with vb2 and these helpers.
Finally remove the users field: this information is also available from
the core framework, no need to keep track of it in the driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that this driver uses v4l2_fh, it is trivial to add support for
control events. Again, this fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use struct v4l2_fh to represent a filehandle. This fixes the missing
g/s_priority handling of this driver that v4l2-compliance complained
about.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No controls were reported, even though the ov7670 does have controls.
Two reasons for this: the v4l2_ctrl_handler_init() call must come
before the ov7670 is loaded (otherwise the ov7670 won't know that
its controls should be added to the bridge driver), and the
v4l2_ctrl_handler_free() call at the end should only be called if
the ret value is non-zero (otherwise you would just free all the
controls that were just added).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The colorspace field wasn't filled in properly. This fixes a v4l2-compliance
failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The width and height should be checked in the enum_frame_interval
op. This fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TV standards make no sense for webcam drivers, so drop these dummy
functions. This stops v4l2-compliance from complaining about this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bus_info field of struct v4l2_querycap wasn't filled in and
v4l2-compliance complained about that. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must set timestamp_flags in vb2_queue otherwise vb2 will complain
loudly about it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Running v4l2-compliance on my usbtv stick revealed two failures:
1) Correct handling of CREATE_BUFS in usbtv_queue_setup was missing. Added this.
2) The sequence counter wasn't reset to 0 when starting streaming.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The patches that added support for HVR2255 and HVR2205 added
some CodingStyle issues.
Better to fix it sooner than latter.
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the VIDIOC_QUERYCAP warning due to the missing device_caps. Don't fill
in the version field, the V4L2 core will do that for you.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.19 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
QAM mode in the LGDT3306 auto detects inversion. VSB does not.
Forgot to include tis fact in the original patch set.
Tested with QAM and VSB after this patch, working fine.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Updates the copyright notes at the saa7164 driver.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding support for the Hauppauge HVR2255 and Hauppauge HVR2205
PCIe cards. Digital TV for DVB-T and ATSC/US-Cable is known to
work. Support for analog RF tuners does not work due to
a lack of analog support in the upstream SI2157 driver.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
SI2168/SI2157 issue single byte address reads. Add support
for these.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This needs to be signed or there is a risk of hitting a forever loop.
Fixes: c4c0283ab3 ('[media] media: i2c: add support for omnivision's ov2659 sensor')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently vb2 core acquires mmap_sem just around call to
__qbuf_userptr(). However since commit f035eb4e97 (videobuf2: fix
lockdep warning) it isn't necessary to acquire it so early as we no
longer have to drop queue mutex before acquiring mmap_sem. So push
acquisition of mmap_sem down into .get_userptr and .put_userptr memops
so that the semaphore is acquired for a shorter time and it is clearer
what it is needed for.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This change will not change timing calculation. In CVT generator
spreadsheet the nominal value of hsync (as a percentage of line)
is 8 percent.
Cc: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wrong values of hfreq and image height can lead to strange timings.
Avoid timing calculations for such values.
Suggested By: Martin Bugge <marbugge@cisco.com>
Cc: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Changed the rounding calculation for hblank and hsync to match it
to equations in cvt and gtf standards.
In cvt calculation, hsync needs to be rounded down.
In gtf calculations, hblank needs to be rounded to nearest multiple
of twice the cell granularity and hsync needs to be rounded to the
nearest multiple of cell granularity.
Cc: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Changed the rounding offsets used in vsync_bp calculation in cvt and
gtf timings. The results for vsync_bp should now match with results
from timing generator spreadsheets for cvt and gtf standards.
In the vsync_bp calculation for cvt, always round down the value of
(CVT_MIN_VSYNC_BP / h_period_est) and then add 1. It thus, reflects
the equation used in timing generator spreadsheet. Using 1999999 as
rounding offset, could pontentially lead to bumping up the vsync_bp
value by extra 1.
In the vsync_bp calculations for gtf, instead of round up or round
down, round the (CVT_MIN_VSYNC_BP / h_period_est) to the nearest
integer.
Thanks to Martin Bugge <marbugge@cisco.com> for validating with
standards and suggestions on equations.
Cc: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
ERROR: "dma_unmap_sg" [drivers/media/v4l2-core/videobuf2-dma-sg.ko] undefined!
ERROR: "dma_map_sg" [drivers/media/v4l2-core/videobuf2-dma-sg.ko] undefined!
ERROR: "dma_sync_sg_for_cpu" [drivers/media/v4l2-core/videobuf2-dma-sg.ko] undefined!
VIDEOBUF2_DMA_SG cannot be enabled manually by the user, it's always
selected automatically by drivers that need it. Several of those drivers
already have an explicit dependency on HAS_DMA.
Make VIDEOBUF2_DMA_SG depend on HAS_DMA. This makes it easier to find
drivers that select VIDEOBUF2_DMA_SG without depending on HAS_DMA, as
Kconfig will give a warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_XILINX && VIDEO_DM365_VPFE && VIDEO_DT3155 && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’
VIDEO_XILINX selects VIDEOBUF2_DMA_CONTIG, which bypasses its dependency
on HAS_DMA. Make VIDEO_XILINX depend on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix several typos inside the driver's comments.
Signed-off-by: Cheolhyun Park <pch851130@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All masks for timings are different between ADV7604 and ADV7611.
Most of the values have 1 precision bit more in the latter.
Fix this by adding new fields to the chip_info structure.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If pci_disable_device() isn't called when the driver is removed, then
the next time when it is loaded the irq isn't found.
I'm pretty sure this used to work in the past, but calling
pci_disable_device() is clearly the correct method and this makes
it work again.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix three v4l2-compliance failures:
- the colorspace wasn't set in vidioc_try_fmt_vid_cap().
- the field wasn't set in v4l2_buffer when vb2_buffer_done() was called.
- the sequence wasn't set in v4l2_buffer when vb2_buffer_done() was called.
This fix also removes the unused buf->count field and starts the count
at 0 instead of 1.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The format description is now filled in by the core, so we can
drop this in this virtual driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The format description is now filled in by the core, so we can
drop this in this virtual m2m driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The changeset ba3002045f added a logic at the core to fill
the format description, however, a break is missing on one of
the formats, as reported by smatch:
drivers/media/v4l2-core/v4l2-ioctl.c:1211 v4l_fill_fmtdesc() warn: missing break? reassigning 'descr'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The descriptions used in drivers for the formats returned with ENUM_FMT
are all over the place.
So instead allow the core to fill them in if the driver didn't. This
allows drivers to drop the description and flags.
Based on an earlier patch from Philipp Zabel:
http://comments.gmane.org/gmane.linux.drivers.video-input-infrastructure/81411
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/m2m-deinterlace.c:1063 deinterlace_probe() info: ignoring unreachable code.
There's no need to call v4l2_m2m_release() here, as the last possible
failure in this code is to allocate the m2m struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
as reported by smatch:
drivers/media/pci/bt8xx/bttv-audio-hook.c:201 lt9415_audio() warn: bitwise AND condition is false here
drivers/media/pci/bt8xx/bttv-audio-hook.c:241 winfast2000_audio() warn: bitwise AND condition is false here
drivers/media/pci/bt8xx/bttv-audio-hook.c:276 pvbt878p9b_audio() warn: bitwise AND condition is false here
drivers/media/pci/bt8xx/bttv-audio-hook.c:307 fv2000s_audio() warn: bitwise AND condition is false here
drivers/media/pci/bt8xx/bttv-audio-hook.c:334 windvr_audio() warn: bitwise AND condition is false here
drivers/media/pci/bt8xx/bttv-audio-hook.c:371 adtvk503_audio() warn: bitwise AND condition is false here
there are some serious issues at the audio hook implementation.
They're not following what's specified at the DocBook:
http://linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-tuner.html#tuner-audmode
Basically, it was assuming that the audmode (V4L2_TUNER_MODE_foo)
is a variable with a bit maskk. However, it isn't.
The bitmask only applies to rxsubchans field (V4L2_TUNER_SUB_foo).
As the code is also too complex, and not all hooks were returning
both audmode and rxsubchans to a VIDIOC_G_TUNER, rewrite the
functions, in order to fix both for get and set tuner ioctls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/tda10086.c:476 tda10086_get_frontend() warn: should 'tda10086_read_byte(state, 81) << 8' be a 64 bit type?
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
redrat3_send_cmd() can return an error or the read data. However,
it currently returns an u8, as reported by smatch:
drivers/media/rc/redrat3.c:416 redrat3_send_cmd() warn: signedness bug returning '(-12)'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since the first version of this driver, the remote controller
code is disabled, adding an early return inside vp702x_rc_query().
Let's disable the code with #if 0, to remove this warning:
drivers/media/usb/dvb-usb/vp702x.c:268 vp702x_rc_query() info: ignoring unreachable code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The indentation on this driver were deadly broken. On lots
of places, it was using 4 spaces instead of tab to indent.
On other parts, it were using tabs.
Also, on several places, it were not even being properly aligned,
as reported by smatch:
drivers/media/dvb-frontends/dib0070.c:179 dib0070_set_bandwidth() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:198 dib0070_captrim() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:246 dib0070_set_ctrl_lo5() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:260 dib0070_ctrl_agc_filter() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:494 dib0070_tune_digital() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:498 dib0070_tune_digital() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:655 dib0070_reset() warn: inconsistent indenting
drivers/media/dvb-frontends/dib0070.c:711 dib0070_reset() warn: curly braces intended?
drivers/media/dvb-frontends/dib0070.c:713 dib0070_reset() warn: inconsistent indenting
My first idea were to leave it as-is or to just touch the above.
However, this won't be fixing anything. So, as painful as it
is, let's fix indentation globally on the driver, and then
address the inconsistencies.
Hopefully, this driver doesn't have much patches, so it likely
won't conflict to any other patch during this merge window.
Besides the big size of this patch, no functional changes
were done.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov7670_s_exp() checks read error for 2 registers: REG_COM1
and REG_COM8. But, although it uses the value latter, it
doesn't check errors on REG_AECHH read. Yet, as it is doing
a bitmask operation there, the read operation should succeed.
So, fix the code to also check if this succeeded.
This fixes this smatch report:
drivers/media/i2c/ov7670.c:1366 ov7670_s_exp() warn: inconsistent indenting
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/stv0297.c:140 stv0297_get_symbolrate() warn: should 'stv0297_readreg(state, 86) << 8' be a 64 bit type?
drivers/media/dvb-frontends/stv0297.c:141 stv0297_get_symbolrate() warn: should 'stv0297_readreg(state, 87) << 16' be a 64 bit type?
drivers/media/dvb-frontends/stv0297.c:142 stv0297_get_symbolrate() warn: should 'stv0297_readreg(state, 88) << 24' be a 64 bit type?
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/tuners/qt1010.c:357 qt1010_init() error: buffer overflow 'i2c_data' 34 <= 34
This should not happen with the current code, as the i2c_data array
doesn't end with a QT1010_M1, but it doesn't hurt add a BUG_ON
to notify if one modifies it and breaks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/usb/gspca/zc3xx.c:5994 transfer_update() info: ignoring unreachable code.
That happens because there's a return that it is never called,
as the work queue runs an infinite loop, except when the device is
put to sleep or an error happens.
When an error happens, a break statement is enough to go out of
the loop. So, let's remove the goto, as break is the typical
instruction used to end a loop.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If userspace sends an invalid bandwidth, it should either return
EINVAL or switch to auto mode.
This driver will go past an array and program the hardware on a
wrong way if this happens.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up to 7 values:
drivers/media/dvb-frontends/s5h1420.c:193 s5h1420_send_master_cmd() error: buffer overflow 'cmd->msg' 6 <= 7
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/dib3000mc.c:134 dib3000mc_setup_pwm_state() warn: inconsistent indenting
drivers/media/dvb-frontends/dib3000mc.c:144 dib3000mc_setup_pwm_state() warn: inconsistent indenting
drivers/media/dvb-frontends/dib3000mc.c:420 dib3000mc_sleep() warn: inconsistent indenting
drivers/media/dvb-frontends/dib3000mc.c:453 dib3000mc_set_channel_cfg() warn: inconsistent indenting
The last one is actually due to a commented code. Let's rework
it, in order to remove the sparse warning without removing the
dead code, as it may be useful in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/usb/go7007/go7007-driver.c:452 frame_boundary() warn: variable dereferenced before check 'vb' (see line 449)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using static const allows the compiler to optimize the code.
Before static const:
text data bss dec hex filename
4982 524 1568 7074 1ba2 drivers/media/tuners/qt1010.o
After static const:
text data bss dec hex filename
4714 524 1568 6806 1a96 drivers/media/tuners/qt1010.o
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The streg_cbdata can have a negative error value. So, it should be
an integer, and not u8, as reported by smatch:
drivers/media/radio/wl128x/fmdrv_common.c:1517 fmc_prepare() warn: assigning (-115) to unsigned variable 'fmdev->streg_cbdata'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some false-positive warnings produced by smatch:
drivers/media/rc/ir-sony-decoder.c:129 ir_sony_decode() warn: missing break? reassigning 'data->state'
drivers/media/rc/ir-sony-decoder.c:137 ir_sony_decode() warn: missing break? reassigning 'data->state'
drivers/media/rc/ir-sony-decoder.c:165 ir_sony_decode() warn: missing break? reassigning 'data->state'
This is due to the logic used there to detect the need of a break.
While those are false positives, it is easy to get rid of them without
any drawbacks. The side effect is a cleaner function, with is good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/s5p-mfc/s5p_mfc.c:1340 s5p_mfc_runtime_resume() warn: this array is probably non-NULL. 'm_dev->alloc_ctx'
alloc_ctx can never be NULL, as it is embeeded inside the struct
s5p_mfc_dev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/zoran/zoran_device.c:1594 zoran_init_hardware() warn: inconsistent indenting
Fix indent. While here, fix CodingStyle and remove dead code, as it
can always be recovered from git logs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/ivtv/ivtv-driver.c:832 ivtv_init_struct2() error: buffer overflow 'itv->card->video_inputs' 6 <= 6
That happens because nof_inputs and nof_audio_inputs can be initialized
as IVTV_CARD_MAX_VIDEO_INPUTS, instead of IVTV_CARD_MAX_VIDEO_INPUTS - 1.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/i2c/saa717x.c:155 saa717x_read() warn: mask and shift to zero
drivers/media/i2c/saa717x.c:155 saa717x_read() warn: mask and shift to zero
This is done right at saa717x_write(), but the read function is
broken. Thankfully, there's just one place at saa717x driver that
uses multibyte read (for status report, via printk).
Yet, let's fix it. From saa717x_write(), it is clear that the
bytes are in little endian:
mm1[4] = (value >> 16) & 0xff;
mm1[3] = (value >> 8) & 0xff;
mm1[2] = value & 0xff;
So, the same order should be valid for read too.
Compile-tested only.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/saa7164/saa7164-core.c:631 saa7164_irq() warn: variable dereferenced before check 'dev' (see line 621)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/ngene/ngene-core.c:1529 init_channel() error: we previously assumed 'chan->fe' could be null (see line 1521)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/cx18/cx18-driver.c:807 cx18_init_struct2() error: buffer overflow 'cx->card->video_inputs' 6 <= 6
That happens because nof_inputs and nof_audio_inputs can be initialized
as CX18_CARD_MAX_VIDEO_INPUTS, instead of CX18_CARD_MAX_VIDEO_INPUTS - 1.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/rc/rc-main.c:749 rc_close() warn: inconsistent indenting
There's an extra space there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/platform/am437x/am437x-vpfe.c: In function 'vpfe_ccdc_update_raw_params':
drivers/media/platform/am437x/am437x-vpfe.c:430:38: warning: variable 'config_params' set but not used [-Wunused-but-set-variable]
struct vpfe_ccdc_config_params_raw *config_params =
^
vpfe_ccdc_update_raw_params() is supposed to update the raw
params at ccdc. However, it is just creating a local var and changing
it.
Compile-tested only.
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In file included from include/uapi/linux/posix_types.h:4:0,
from include/uapi/linux/types.h:13,
from include/linux/types.h:5,
from include/uapi/linux/sysinfo.h:4,
from include/uapi/linux/kernel.h:4,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/input.h:11,
from drivers/media/usb/dvb-usb/dvb-usb.h:13,
from drivers/media/usb/dvb-usb/dib0700.h:13,
from drivers/media/usb/dvb-usb/dib0700_devices.c:9:
drivers/media/dvb-frontends/dib8000.h: In function 'dib8000_attach':
include/linux/stddef.h:8:14: warning: return makes integer from pointer without a cast [-Wint-conversion]
#define NULL ((void *)0)
^
drivers/media/dvb-frontends/dib8000.h:72:9: note: in expansion of macro 'NULL'
return NULL;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In file included from drivers/media/common/b2c2/flexcop-fe-tuner.c:13:0:
drivers/media/dvb-frontends/cx24123.h:54:2: warning: 'cx24123_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
cx24123_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/em28xx/em28xx-dvb.c:46:0:
drivers/media/dvb-frontends/s921.h:40:2: warning: 's921_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
s921_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/em28xx/em28xx-dvb.c:55:0:
drivers/media/dvb-frontends/mb86a20s.h:49:2: warning: 'mb86a20s_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
mb86a20s_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/mb86a20s.h:49:2: warning: 'mb86a20s_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
mb86a20s_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/platform/s3c-camif/camif-capture.c: In function 'sensor_set_power':
drivers/media/platform/s3c-camif/camif-capture.c:118:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == camif->sensor.power_count)
^
drivers/media/platform/s3c-camif/camif-capture.c: In function 'sensor_set_streaming':
drivers/media/platform/s3c-camif/camif-capture.c:134:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == camif->sensor.stream_count)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/i2c/s5k5baf.c: In function 's5k5baf_set_power':
drivers/media/i2c/s5k5baf.c:1057:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on != state->power)
^
drivers/media/i2c/s5k6aa.c: In function 's5k6aa_set_power':
drivers/media/i2c/s5k6aa.c:878:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == s5k6aa->power) {
^
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function 's5c73m3_oif_set_power':
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1456:17: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
} else if (!on == state->power) {
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For these encodings the quantization range should be ignored, since
there is only one possible Y'CbCr encoding.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_BT2020_CONST_LUM.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_BT2020.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a log_status function to the test pattern generator and use that
in vivid. This simplifies debugging complex colorspace problems.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the VIVID_WEBCAM_SIZES constant where appropriate and add a
1920x1080 pixel frame size setting with frame rates of 2 fps and
5 fps.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree support for adp1653 flash LED driver.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of parsing the link-frequencies property in the driver, let
v4l2_of_alloc_parse_endpoint() do it.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The link-frequencies property is a variable length array of link frequencies
in an endpoint. The array is needed by an increasing number of drivers, so
it makes sense to add it to struct v4l2_of_endpoint.
However, the length of the array is variable and the size of struct
v4l2_of_endpoint is fixed since it is allocated by the caller. The options
here are
1. to define a fixed maximum limit of link frequencies that has to be the
global maximum of all boards. This is seen as problematic since the maximum
could be largish, and everyone hitting the problem would need to submit a
patch to fix it, or
2. parse the property in every driver. This doesn't sound appealing as two
of the three implementations submitted to linux-media were wrong, and one of
them was even merged before this was noticed, or
3. change the interface so that allocating and releasing memory according to
the size of the array is possible. This is what the patch does.
v4l2_of_alloc_parse_endpoint() is just like v4l2_of_parse_endpoint(), but it
will allocate the memory resources needed to store struct v4l2_of_endpoint
and the additional arrays pointed to by this struct. A corresponding release
function v4l2_of_free_endpoint() is provided to release the memory allocated
by v4l2_of_alloc_parse_endpoint().
In addition to this, the link-frequencies property is parsed as well, and
the result is stored to struct v4l2_of_endpoint field link_frequencies.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Zero the entire struct starting from bus_type. As more fields are added, no
changes will be needed in the function to reset their value explicitly.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When stopping abnormally, a driver can't return from wait_for_completion.
This patch resolved this problem by changing wait_for_completion_timeout
from wait_for_completion.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Various formats had their byte ordering implemented incorrectly, and
the V4L2_PIX_FMT_UYVY is actually impossible to create, instead you
get V4L2_PIX_FMT_YVYU.
This was working before commit ad6ac45222
("add new formats support for marvell-ccic driver"). That commit broke
the original format support and the OLPC XO-1 laptop showed wrong
colors ever since (if you are crazy enough to attempt to run the latest
kernel on it, like I did).
The email addresses of the authors of that patch are no longer valid,
so without a way to reach them and ask them about their test setup
I am going with what I can test on the OLPC laptop.
If this breaks something for someone on their non-OLPC setup, then
contact the linux-media mailinglist. My suspicion however is that
that commit went in untested.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: <stable@vger.kernel.org> # for v3.19 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil