If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 2fd36c5526 ("i2c: core: Map OF IRQ at probe time"),
i2c slaves without interrupts (e.g. da9210 and at24 on r8a7791/koelsch)
fail to probe:
at24: probe of 2-0050 failed with error -22
da9210: probe of 6-0068 failed with error -22
This happens because the call to of_irq_get() in i2c_device_probe()
returns -EINVAL.
If a device node does not have an "interrupts" property,
of_irq_parse_one() fails. Unlike irq_of_parse_and_map(), of_irq_get()
does not ignore errors from of_irq_parse_one(), but forwards them.
Make i2c_device_probe() ignore all errors but -EPROBE_DEFER to fix this,
just like platform_get_irq() and platform_get_irq_byname() already do.
Fixes: 2fd36c5526 ("i2c: core: Map OF IRQ at probe time")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver tried to access device registers with the (little-endian)
iowrite/ioread functions. While this worked on little-endian machines
(e.g. Microblaze with AXI bus), it made the driver unusable on
big-endian machines (e.g. PPC405 with PLB).
During the probe function, the driver tried to write a 32-bit reset mask
into the reset register. This caused an error interrupt on big-endian
systems, because the device detected an invalid (byte-swapped) reset
mask. The result was an Oops.
The patch implements an endianness detection similar to the one used in
other Xilinx drivers like drivers/spi/spi-xilinx.c. It was tested on a
PPC405/PLB system.
Signed-off-by: Thomas Gessler <Thomas.Gessler@exp2.physik.uni-giessen.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I have a at24 EEPROM connected via i2c bus provided by ISCH i2c
bus driver. This bus driver does not support
I2C_FUNC_SMBUS_WRITE_I2C_BLOCK and so I was looking for a way
to be able to write the eeprom. This patch adds support for
I2C_SMBUS_BYTE_DATA writing via i2c_smbus_write_byte_data.
It is quite slow, but it works.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
[wsa: s/use_smbuse_write/use_smbus_write/]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No user needs magic hex values, makes this debug output. Add DMA info.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address is still handled using the old state
machine, it is sending the actual data that is done via DMA. This is
least intrusive and allows us to work with the message buffers directly
instead of preparing a custom buffer which involves copying the data
around.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed an uninitialized var problem]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improves readability and reduces chances of duplicates.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Amend the at91 i2c pin controller to set the state of the pins to:
- "default" on resume.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enforces correct I2C error returned codes from Freescale's
MPC i2c bus driver, allowing for proper user-space/kernel error
handling.
Signed-off-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't log the host status register value in i801_isr(), it has very
little value and fills up the log when debugging is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a control bit in the PCI configuration space which disables
interrupts. If this bit is set, the driver should not try to make use
of interrupts, it won't receive any.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-i801 driver can work without interrupts, so there is no reason
to make a request_irq failure fatal. Instead we can simply fallback
to polling.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some systems have been reported to have trouble with interrupts. Use
wait_event_timeout() instead of wait_event() so we don't get stuck in
that case, and log the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As show in I2C specification:
- Standard-mode: the minimum HIGH period of the scl clock is 4.0us
the minimum LOW period of the scl clock is 4.7us
- Fast-mode: the minimum HIGH period of the scl clock is 0.6us
the minimum LOW period of the scl clock is 1.3us
I have measured i2c SCL waveforms in fast-mode by oscilloscope
on rk3288-pinky board. the LOW period of the scl clock is 1.3us.
It is so critical that we must adjust LOW division to increase
the LOW period of the scl clock.
Thanks Doug for the suggestion about division formulas.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When a signal is caught while the i2c-davinci bus driver is
transferring, the driver just "abandons" the transfer and leaves the
controller to fend for itself. The next I2C transaction will find the
controller in an undefined state and often results in a stream of
"initiating i2c bus recovery" messages until the controller arrives in a
defined state. This behaviour also sends out "half" or possibly even
mixed messages to I2C client devices which may put them in an undesired
state as well. So, let's get simply uninterruptible.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of i2c traffic within short period of time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C clients instantiated from OF get their IRQ mapped at device
registration time. This leads to the IRQ being silently ignored if the
related irqchip hasn't been proved yet.
Fix this by moving IRQ mapping at probe time using of_get_irq(). The
function operates as irq_of_parse_and_map() but additionally returns
-EPROBE_DEFER if the irqchip isn't available, allowing us to defer I2C
client probing.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The function will be used by the I2C core which can be compiled as a
module.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for r8a73a4 (R-Mobile APE6) and sh73a0 (SH-Mobile AG5).
On these SoCs, the operating clock runs faster that on previous SoCs,
and the internal SCL clock counter gets incremented every 2 clocks of
the operating clock, just like on R-Car Gen2.
Cfr. the "/2" in the calculation of ICCL/ICCH in section "I2C Bus
Interface (IIC)", subsection "Transfer Rate" of the datasheets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Explicitly list the various SoC-specific compatible properties.
This allows checkpatch to validate DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CBMO
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Another quiet week:
- A fix to silence edma probe error on non-supported platforms from Arnd
- A fix to enable the PL clock for Parallella, to make mainline usable with
the SDK.
- A somewhat verbose fix for the PLL clock tree on VF610
- Enabling of SD/MMC on one of the VF610-based boards (for testing)
- A fix for i.MX where CONFIG_SPI used to be implicitly enabled and now needs
to be added to the defconfig instead
- Another maintainer added for bcm2835: Lee Jones
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bOlr
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Pull devicetree bugfix from Grant Likely:
"One buffer overflow bug that shouldn't be left around"
* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of: Fix overflow bug in string property parsing functions
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Here are 3 tiny fixes for 3.18-rc4. One fixes up a long-stading race
condition in the driver core for removing directories in
/sys/devices/virtual/ and the other 2 fix up the wording of a new
Kconfig option that was added in 3.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZX4ACgkQMUfUDdst+ym9/gCfbVnQzjAEh3OL0I+mTMjAMxhX
AwwAoK1f/ZK02U/vz/u/dpK38LM3FhH+
=Q4mc
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZfMACgkQMUfUDdst+ylycwCdGD/ZN7f6rBq7EG0YqBngs5zX
AWwAoK+l0zqYCQ6N8s+ZnQ7l1Ijo7HhR
=vEmW
-----END PGP SIGNATURE-----
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZmgACgkQMUfUDdst+ymt1wCgj+RYlAC//NhPIjTHmvHHb9gs
8o0AoJErubEEF3VgbAjvQg1lPr8xSHtR
=7Gmf
-----END PGP SIGNATURE-----
Merge tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
reported issues"
* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix pty master poll() after slave closes v2
serial: of-serial: fix uninitialized kmalloc variable
tty/vt: don't set font mappings on vc not supporting this
tty: serial: 8250_mtk: Fix quot calculation
tty: Prevent "read/write wait queue active!" log flooding
tty: Fix high cpu load if tty is unreleaseable
serial: Fix divide-by-zero fault in uart_get_divisor()
Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device ids for
existing drivers. Full details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZzgACgkQMUfUDdst+ylTIgCdG8L088p1OqgEdcL+J0ceYS51
PQAAn3O4t962htLmX0XuQmfMWTyBqn11
=3auS
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.18-rc4.
Just a bunch of little fixes resolving reported issues and new device
ids for existing drivers. Full details are in the shortlog"
* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: Update default usb-storage delay_use value in kernel-parameters.txt
USB: cdc-acm: add quirk for control-line state requests
phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
USB: cdc-acm: only raise DTR on transitions from B0
Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
usb: core: notify disconnection when core detects disconnect
usb: core: need to call usb_phy_notify_connect after device setup
uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
xhci: no switching back on non-ULT Haswell
USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
USB: quirks: enable device-qualifier quirk for another Elan touchscreen
MAINTAINERS: Remove duplicate entry for usbip driver
usb: storage: fix build warnings !CONFIG_PM
usb: Remove references to non-existent PLAT_S5P symbol
uas: Add NO_ATA_1X for VIA VL711 devices
xhci: Disable streams on Asmedia 1042 xhci controllers
USB: HWA: fix a warning message
uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
usb-storage: handle a skipped data phase
...
The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.
Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.
Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull i2c bugfixes from Wolfram Sang:
"One bigger cleanup (FSF address removal) and two bugfixes for I2C"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
Pull irq fixes from Thomas Gleixner:
"Two fixlets for the armada SoC interrupt controller"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: armada-370-xp: Fix MPIC interrupt handling
irqchip: armada-370-xp: Fix MSI interrupt handling
Pull media fixes from Mauro Carvalho Chehab:
"For:
- some regression fixes at the Remote Controller core and imon driver
- a build fix for certain randconfigs with ir-hix5hd2
- don't feed power to satellite system at ds3000 driver init
It also contains some fixes for drivers added for Kernel 3.18:
- some fixes at the new ISDB-S driver, and the corresponding bits to
fix some descriptors for this Japanese TV standard at the DVB core
- two warning cleanups for sp2 driver if PM is disabled
- change the default mode for the new vivid driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] sp2: sp2_init() can be static
[media] dvb:tc90522: fix always-false expression
[media] dvb-core: set default properties of ISDB-S
[media] dvb:tc90522: fix stats report
[media] vivid: default to single planar device instances
[media] imon: fix other RC type protocol support
[media] ir-hix5hd2 fix build warning
[media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
[media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
[media] rc-core: fix protocol_change regression in ir_raw_event_register
Pull MIPS updates from Ralf Baechle:
"This weeks' round of MIPS bug fixes for 3.18:
- wire up the bpf syscall
- fix TLB dump output for R3000 class TLBs
- fix strnlen_user return value if no NUL character was found.
- fix build with binutils 2.24.51+. While there is no binutils 2.25
release yet, toolchains derived from binutils 2.24.51+ are already
in common use.
- the Octeon GPIO code forgot to offline GPIO IRQs.
- fix build error for XLP.
- fix possible BUG assertion with EVA for CMA"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix build with binutils 2.24.51+
MIPS: R3000: Fix debug output for Virtual page number
MIPS: Fix strnlen_user() return value in case of overlong strings.
MIPS: CMA: Do not reserve memory if not required
MIPS: Wire up bpf syscall.
MIPS/Xlp: Remove the dead function destroy_irq() to fix build error
MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware
This update fixes:
- incorrect warnings about i_mutex locking in
pagecache_isize_extended() and updates comments to match expected
locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8S0c
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update fixes a warning in the new pagecache_isize_extended() and
updates some related comments, another fix for zero-range
misbehaviour, and an unforntuately large set of fixes for regressions
in the bulkstat code.
The bulkstat fixes are large but necessary. I wouldn't normally push
such a rework for a -rcX update, but right now xfsdump can silently
create incomplete dumps on 3.17 and it's possible that even xfsrestore
won't notice that the dumps were incomplete. Hence we need to get
this update into 3.17-stable kernels ASAP.
In more detail, the refactoring work I committed in 3.17 has exposed a
major hole in our QA coverage. With both xfsdump (the major user of
bulkstat) and xfsrestore silently ignoring missing files in the
dump/restore process, incomplete dumps were going unnoticed if they
were being triggered. Many of the dump/restore filesets were so small
that they didn't evenhave a chance of triggering the loop iteration
bugs we introduced in 3.17, so we didn't exercise the code
sufficiently, either.
We have already taken steps to improve QA coverage in xfstests to
avoid this happening again, and I've done a lot of manual verification
of dump/restore on very large data sets (tens of millions of inodes)
of the past week to verify this patch set results in bulkstat behaving
the same way as it does on 3.16.
Unfortunately, the fixes are not exactly simple - in tracking down the
problem historic API warts were discovered (e.g xfsdump has been
working around a 20 year old bug in the bulkstat API for the past 10
years) and so that complicated the process of diagnosing and fixing
the problems. i.e. we had to fix bugs in the code as well as
discover and re-introduce the userspace visible API bugs that we
unwittingly "fixed" in 3.17 that xfsdump relied on to work correctly.
Summary:
- incorrect warnings about i_mutex locking in pagecache_isize_extended()
and updates comments to match expected locking
- another zero-range bug fix for stray file size updates
- a bunch of fixes for regression in the bulkstat code introduced in
3.17"
* tag 'xfs-for-linus-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
xfs: rework zero range to prevent invalid i_size updates
mm: Remove false WARN_ON from pagecache_isize_extended()
xfs: Check error during inode btree iteration in xfs_bulkstat()
xfs: bulkstat doesn't release AGI buffer on error
More changes than I'd like here, most of them for a single bug repeated
in a bunch of drivers with data not being initialized correctly, plus a
fix to lower the severity of a warning introduced in the last merge
window which can legitimately go off so we don't want to alarm users
excessively.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUXKcAAAoJECTWi3JdVIfQEv4H/2JKlUtohFiCokDE3j9e9FG/
sGBUokIM4FLjdjirjalO5dvwaegsy6SHIcNJQXJJEPvOqaq5/sP1lxvEDMnMcvyd
jdvZdFPTRsY6X78047kBqVV6zibI4RYy2uQSOsmtST8+efkrAfw41t6ZV6AxX8mx
hMmHSehXsEsc0hwslGh9xvtUECqKI3McdcL2HSyl3jviRiPnvgsKXCL9HjSeIVs7
A2PZndUpOab86fApZpkJYSkdgqUbag/yyClasdOIS8B1HRreURVlgKM8oiO2xTbg
0q2uHVUGdrBoIx8M2zybVdJRc46zNUZhCG3HAOkOj8I6ekRtn6EcZqdwkUvPBLA=
=iaBY
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"More changes than I'd like here, most of them for a single bug
repeated in a bunch of drivers with data not being initialized
correctly, plus a fix to lower the severity of a warning introduced in
the last merge window which can legitimately go off so we don't want
to alarm users excessively"
* tag 'regulator-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mpa01: zero-initialize regulator match table array
regulator: max8660: zero-initialize regulator match table array
regulator: max77802: zero-initialize regulator match table
regulator: max77686: zero-initialize regulator match table
regulator: max1586: zero-initialize regulator match table array
regulator: max77693: Fix use of uninitialized regulator config
regulator: of: Lower the severity of the error with no container
A couple of small driver fixes for v3.18, both quite problematic if you
hit a use case that's affected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUXKDwAAoJECTWi3JdVIfQIn8H/1+j+DVzOISeS+xivOrcAc6h
+FeTWRUJMP/1jqeqWImLB8jFpyAMF6l6kV/D9XOc+FojmCM/xcg4ewj+Z/uqYekO
a8TU9+ymHGuPpZcn7LEGZy2KjvKPS7KqBxZ9FNGiFhfDvv41vuYOKReU6Dauc7m9
FNPApIG0l1J0SA8Osok3bip7oQGcx1hJsmDB2X0GkN7QSk4+FCYxmk0vtlXJK0at
1aksQsgwv4GZLrFD01V2kxyYFubbt5JEDOKRU+QvNmUB+gohdZ6cAHBy1rGomc4a
/Twru9QP/4Pve7JgSNnuoQoSiE7GWrxDa40CFpB89ZHnhJAz/1utJcuK2OzDcKo=
=hDs9
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi bugfixes from Mark Brown:
"A couple of small driver fixes for v3.18, both quite problematic if
you hit a use case that's affected"
* tag 'spi-v3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM
spi: fsl-dspi: Fix CTAR selection
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Cc: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clients instantiated from OF get an IRQ mapping created at device
registration time. Dispose the mapping when the client is removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
iowait is for blkio [1]. I2C shouldn't use it.
[1] https://lkml.org/lkml/2014/11/3/317
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@kernel.org
Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1
second (commit a4a47bc03f), but
kernel-parameters.txt wasn't updated to reflect that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
-----------------------------------------------------
<4>[ 3965.441471] WARNING: at ...include/linux/kref.h:41 kobject_get+0x33/0x40()
<4>[ 3965.441474] Hardware name: Romley
<4>[ 3965.441475] Modules linked in: isd_iop(O) isd_xda(O)...
...
<4>[ 3965.441605] Call Trace:
<4>[ 3965.441611] [<ffffffff8103717a>] warn_slowpath_common+0x7a/0xb0
<4>[ 3965.441615] [<ffffffff810371c5>] warn_slowpath_null+0x15/0x20
<4>[ 3965.441618] [<ffffffff81215963>] kobject_get+0x33/0x40
<4>[ 3965.441624] [<ffffffff812d1e45>] get_device_parent.isra.11+0x135/0x1f0
<4>[ 3965.441627] [<ffffffff812d22d4>] device_add+0xd4/0x6d0
<4>[ 3965.441631] [<ffffffff812d0dbc>] ? dev_set_name+0x3c/0x40
....
<2>[ 3965.441912] kernel BUG at ..../fs/sysfs/group.c:65!
<4>[ 3965.441915] invalid opcode: 0000 [#1] SMP
...
<4>[ 3965.686743] [<ffffffff811a677e>] sysfs_create_group+0xe/0x10
<4>[ 3965.686748] [<ffffffff810cfb04>] blk_trace_init_sysfs+0x14/0x20
<4>[ 3965.686753] [<ffffffff811fcabb>] blk_register_queue+0x3b/0x120
<4>[ 3965.686756] [<ffffffff812030bc>] add_disk+0x1cc/0x490
....
-------------------------------------------------------
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Weng Meiling <wengmeiling.weng@huawei.com>
Cc: <stable@vger.kernel.org> #3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yao Yuan