Everything has been set up in the PCI probe function.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
No net_device.irq removal yet. The driver probe, remove and failure
paths need some care beforehand.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
- pci_resource_start() can be removed from sis900_get_mac_addr() because
the IO range is maped and stored into the device private struct early
in the device probe function.
- the driver contains a few direct accesses to low IO ports that forbid
to re(#)define the usual out{l, w, b} macros.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Daniele Venzano <venza@brownhat.org>
The bulk of the patch comes from the __iomem changes.
- the phy read and write operations were carrying the chip id deep
down the call chain. Let's waste a pointer and contain the flying
spaghetti monster.
- phy_{read, write}_1bit only need to access the DCR9 register. The loss
of generality here should not hurt.
- removed a leftover printk of the EISA era. This is a pure PCI device.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
The eeprom registers always use the same PCI bar whereas the general
registers may either use the same mapping as the eeprom registers or
a different one. It is thus possible to simplify parse_eeprom().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The device private data pointer can not be NULL in smsc9420_open().
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
- unbalanced pci_disable_device
- PCI ressources were not released
- mismatching pci_alloc_.../kfree pairs are replaced by DMA alloc helpers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Ack-by: Grant Grundler <grundler@parisc-linux.org>
Some settings are duplicated between ethtool link management and module
options. The latter is trimmed. The half duplex, speed and autonegotiation
defaults are kept unchanged.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ion Badulescu <ionut@badula.org>
It's useless to check mem_start on a newly allocated device as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ion Badulescu <ionut@badula.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conditional which decides to skip inactive filters does not
change with the change of loop index, so it is unnecessary to
check them many times.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3e4d3af501 (mm: stack based kmap_atomic()) we dont have
to disable BH anymore while mapping skb frags.
We can remove kmap_skb_frag() / kunmap_skb_frag() helpers and use
kmap_atomic() / kunmap_atomic()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is using the DCB netlink to set rate limit per ETS TC
Values are accepted in Kbps and rounded up to the nearest multiply of 100Mbps.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although not specified in 8021Qaz spec, it could be useful to enable drivers
whose HW supports setting a rate limit for an ETS TC. This patch adds this
optional attribute to DCB netlink. To use it, drivers should implement and
register the callbacks ieee_setmaxrate and ieee_getmaxrate. The units are 64
bits long and specified in Kbps to enable usage over both slow and very fast
networks.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tagged traffic and untagged traffic use tc tool mapping.
Treat RDMA TOS same as IP TOS when mapping to SL
Signed-off-by: Amir Vadai <amirv@mellanox.com>
CC: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to export this to enable drivers use rt_tos2priority()
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since vlan egress map is only good for tagged traffic, need to have other
mapping to be used by untagged traffic.
For that, the driver uses sch_mqprio mapping. This mapping could be set by
using tc tool from iproute2 package.
Mapped UP will be used by the HW for QoS purposes, but won't go out on the
wire.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller