The following patch for megaraid_sas loads the correct raid context timeout
value for multpathing and clustering.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Host lock is added back around queuecommand. Host lock removal can create race
conditon between ISR path(when RAID map update interrupt is raised) and IO
build path of driver, since IO build path is making use of RAID map, and in
case of RAID map update interrupt, old RAID map copy is memset to zero, which
some IOs may be referencing in build IO path. Changes done for performance
boost- 1) Added code to set SMP IRQ affinity per CPU. 2) Pass MSI-x index,
while issuing sysPD IO.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If consistent DMA mask is set to 64 bit, fall back to 32bit DMA mask and 32bit consistent DMA mask.
64bit consistent DMA mask may be set on some 64bit DMA slot, which causes DMA offset "10000000000000" and
MFI_INIT and IOCTL frames will have high memory addresses, leads to firmware FAULT.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Don't wait forever for firmware response for internal DCMDs sent from driver
firmware. Such DCMDs will be posted to firmware with timeout. Timeout is also
introduced for DCMD sent to abort the commands. DCMD sent via IOCTL path will
still be always blocking to keep the IOCTL design intact.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When megasas_get_pd_list() fails we cannot detect any drives,
so we should be checking the return value accordingly.
[jejb: checkpatch fix]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When no HBA is found we should be returning '-ENXIO' to be consistent
with the other return values.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The pointer to the queue info structure is potentially
a 64-bit value, so we should be using the correct macros
to set the values in the init frame.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
pthru32->dataxferlen comes from the user so we need to check that it's
not too large so we don't overflow the buffer.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The assumption that sizeof(long) >= sizeof(resource_size_t) can lead to
truncation of the PCI resource address, meaning this driver didn't work
on 32-bit systems with 64-bit PCI adressing ranges.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.
This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.
[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
There is syncronization problem between sysPD IO path and AEN path. Driver
maintains instance->pd_list[] array, which will get updated(by calling
function megasas_get_pd_list[]), whenever any of below events occurs-
MR_EVT_PD_INSERTED
MR_EVT_PD_REMOVED
MR_EVT_CTRL_HOST_BUS_SCAN_REQUESTED
MR_EVT_FOREIGN_CFG_IMPORTED
At same time running sysPD IO will be accessing the same array
instance->pd_list[], which is getting updated in AEN path, because of this IO
may not get correct PD info from instance->pd_list[] array.
Signed-off-by: Adam Radford <adam.radford@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed two issues in this patch-
1) In function megasas_get_pd_list(), data read(pd_addr->deviceId) from DMAed memory is converted to CPU's endianess.
2) While register AEN, removed some endianness conversion on some fields, since their endianess is already converted.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch set is a set of driver updates (megaraid_sas, fnic, lpfc, ufs,
hpsa) we also have a couple of bug fixes (sd out of bounds and ibmvfc error
handling) and the first round of esas2r checker fixes and finally the much
anticipated big endian additions for megaraid_sas.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSNheiAAoJEDeqqVYsXL0MueMIAKD1kaB0oooRawE1+0vpKmyV
eE2M6trA8ofTeq0z1eNfRsVMkRsUuG9exW0CKS2z6mHiWwQ/zGbqT7ukveW+dMi3
mjKD0yO5ODk6bohWX/LiwZ6NGZSwC0dbIacXNy5ZsXKEizqwo1Jcc7qC/0AWn+o7
WpIL48XLPH0HqjQZ3dvgC6TWeFZOn9cKOWvQQq0S3ENALOx/eLZ+C7VrJLx5Magv
myNOUkTLzdlYglQfjaNO6et98k2oHTrzKwH7U2X6U75q7L8Pkj4RbNzce/Ge301V
u+R1w+BlbeTPdHopTBoTJupsvqDYBZxVwS7rr8nhSvfKduQppHnN6jX8yR4XNeM=
=RG3j
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI driver updates from James Bottomley:
"This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
ibmvfc error handling) and the first round of esas2r checker fixes and
finally the much anticipated big endian additions for megaraid_sas"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] fnic: fnic Driver Tuneables Exposed through CLI
[SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
[SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
[SCSI] fnic: Remove QUEUE_FULL handling code
[SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
[SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
[SCSI] sd: Fix potential out-of-bounds access
[SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
[SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
[SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
[SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
[SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
[SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
[SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
[SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
[SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
[SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
[SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
[SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
[SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
...
This patch will add big endian architecture support to megaraid_sas
driver. The support added is for LSI MegaRAID all generation controllers-
(3Gb/s, 6Gb/s and 12 Gb/s controllers).
We have done basic sanity test @ppc64 arch and @x86_64. Additional
testing/observations are welcome.
[jejb: fix up rejections]
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Fixed several typos in comments in megaraid_mbox.c, megaraid_mm.c
and megaraid_sas_fusion.h.
Signed-off-by: Matthias Schid <aircrach115@gmail.com>
Signed-off-by: Stefan Huber <steffhip@gmail.com>
Signed-off-by: Simon Puels <simon.puels@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Problem: When Hardware IOMMU is on, megaraid_sas driver initialization fails
in kdump kernel with LSI MegaRAID controller(device id-0x73).
Actually this issue needs fix in firmware, but for firmware running in field,
this driver fix is proposed to resolve the issue. At firmware initialization
time, if firmware does not come to ready state, driver will reset the adapter
and retry for firmware transition to ready state unconditionally(not only
executed for kdump kernel).
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On 64 bit then -1UL and -1U are not equal, so these conditions don't
work as intended and it breaks error handling.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 98cb7e44 ([SCSI] megaraid_sas: Sanity check user
supplied length before passing it to dma_alloc_coherent())
introduced a memory leak. Memory allocated for entries
following zero length SGL entries will not be freed.
Reference: http://bugs.debian.org/688198
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: <stable@vger.kernel.org>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This looks like a cut and paste typo to me. Both of the
megasas_read_fw_status_reg_* functions involved are identical though, so
there was no bad behaviour. I changed it for consistency and clarity.
Signed-off-by: James Georgas <soulpa7ch@gmail.com>
Acked-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to differentiate between iMR(no external memory) and MR(with
external memory) controllers.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
MegaRAID older Firmware does not support uneven span configuration for PRL11.
E.g User wants to create 34 Driver PRL11 config, it was not possible using old
firmware, since it was not supported configuration in old firmware
Old Firmware expect even number of Drives in each span and same number of
physical drives at each span. Considering above design, 17 Drives at Span-0
and 17 drives at span-1 was not possible.
Now, using this new feature Firmware and Driver both required changes. New
Firmware can allow user to create 16 Drives at span-0 and 18 Drives at
span-1. This will allow user to create 34 Drives Uneven span PRL11.
RAID map is interface between Driver and FW to fetch all required
fields(attributes) for each Virtual Drives. Since legacy RAID map consider
Even Span design, there was no place to keep Uneven span information in
existing Raid map. Because of this limitation, for Uneven span VD, driver can
not use RAID map.
This patch address the changes required in Driver to support Uneven span PRL11
support.
1. Driver will find if Firmware has UnevenSpanSupport or not by reading
Controller Info.
2. If Firmware has UnvenSpan PRL11 support, then Driver will inform about its
capability of handling UnevenSpan PRL11 to the firmware.
3. Driver will update its copy of span info on each time Raid map update is
called.
4. Follow different IO path if it is Uneven Span. (For Uneven Span, Driver
uses Span Set info to find relavent fields for that particular Virtual
Disk)
More verbose prints will be available by setting "SPAN_DEBUG" to 1 at
compilation time.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This Driver will use more than 8 MSI-x support provided by Invader/Fury max
upto 128 MSI-x.
[jejb: fix checkpatch warning]
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Free event detail memory from more common place, instead of doing it for
limited device types.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Do not return SCSI_MLQUEUE_HOST_BUSY, but send DID_ERROR to SCSI mid-layer, if
adapter is in critical error state. "SCSI_MLQUEUE_HOST_BUSY" will keep same
SCSI command in loop and it is not a right return value, if controller is
hardware critical error.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We should unlock here before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Previously we used PCI_MSI_FLAGS to locate a register in the MSI-X
capability. This did work because the MSI and MSI-X flags happen
to be at the same offsets, but was confusing.
PCI_MSIX_FLAGS_ENABLE is already defined in include/uapi/linux/pci_regs.h,
so no need to define it again.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Adam Radford <aradford@gmail.com>
This patch updates the megaraid_sas driver version and updates
Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will fix an issue where the
driver should not be loading the DevHandle unless FastPath is enabled.
If FastPath was not enabled, this means the hardware raid map
validation failed for some reason, or the map was corrupted, which
could mean the DevHandle could be invalid.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas will allow Fastpath T10PI/DIF
frame builds to work with 4k sector size.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
megaraid use INIT_WORK to declare a hotplug_work, but cast the
hotplug_work from work_struct to delayed_work and
schedule_delayed_work on it. This is very dangerous, as other part of
delayed_work might be kernel memories allocated by others.
With commit 8852aac ("workqueue: mod_delayed_work_on() shouldn't queue
timer on 0 delay"), schedule_delayed_work() will check dwork->timer
before queue_work even when @delay is 0, this causes megaraid code to
hit the BUG_ON() in workqueue code. Change megaraid code to use
delayed work.
Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-scsi@vger.kernel.org
Load io_request->DataLength in bytes for newer firmware that supports high
availability.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use kzalloc rather than kmalloc followed by memset with 0.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a user to adjust the wait time in seconds after I/O timeout before
resetting the adapter.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows a user to adjust the queue depth of the adapter when throttled due
to I/O timeout.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch moves the poll_aen_lock initializer from
megasas_probe_one() to megasas_init(). This prevents a crash when a user
loads the driver and tries to issue a poll() system call on the ioctl
interface with no adapters present.
Signed-off-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We took this lock with spin_lock() so we should unlock it with
spin_unlock() instead of spin_unlock_irq(). This was introduced in
f2c8dc402b "[SCSI] megaraid_mbox: remove scsi_assign_lock usage".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the driver version to
v00.00.06.15-rc1, and updates Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas fixes the fastpath code decision
logic to use fpRead/WriteCapable, fpRead/WriteAcrossStripe flags
instead of the old logic. This fixes a bug where fastpath writes
could be sent to a read only LD.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas removes an incorrect comment and
optimizes the setting of HostMSIxVectors. This was found during a
code review by Tomas Henzl @ RedHat.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This code has never worked correctly, doesn't disable interrupts when
set as a module parameter, doesn't disable interrupts when set after
driver load time in sysfs node, etc.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mask off flags in the ioctl path to prevent memory scribble with older MegaCLI
versions.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas fixes the reglockFlags field for
degraded raid5/6 for MR9360/9380, which will result in a performance
improvement.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway. We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The following patch for megaraid_sas will fix a potential bad pointer access
in megasas_reset_timer(), when a MegaRAID 9265/9285 or 9360/9380 gets a
timeout. megasas_build_io_fusion() sets SCp.ptr to be a struct
megasas_cmd_fusion *, but then megasas_reset_timer() was casting SCp.ptr to be
a struct megasas_cmd *, then trying to access cmd->instance, which is invalid.
Just loading instance from scmd->device->host->hostdata in
megasas_reset_timer() fixes the issue.
Signed-off-by: Adam Radford <aradford@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas updates the
ChangeLog.megaraid_sas file and updates the driver version.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The following patch for megaraid_sas adds a driver workaround for
PERC5/1068 based controller FW that keeps a command from the main
kernel that the driver cannot cancel which was causing a kernel panic
in shutdown of the kdump kernel.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following patch for megaraid_sas converts 6,10,12 byte CDB's to 16
byte CDB for large LBA's for FastPath IO.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The following patch for megaraid_sas disables interrupts and
free_irq() in megasas_shutdown().
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The following patch for megaraid_sas fixes the function
megasas_reset_fusion() and makes the reset code check
MFI_REG_STATE.fault.resetAdapter.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The following patch for megaraid_sas removes un-used function
megasas_return_cmd_for_smid().
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch for megaraid_sas removes the MSI-X black list and uses
MFI_REG_STATE.ready.msiEnable instead.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
These were missed the last time I cleaned this up
globally, because of code moving around or new code
getting merged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The following patch for megaraid_sas fixes fault state handling in
megasas_transition_to_ready().
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch fixes an incorrect tasklet_init() call in
megasas_init_fw() to use instancet->tasklet.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch for megaraid_sas adds a missing check for
MR_EVT_CFG_CLEARED in megasas_aen_polling().
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch for megaraid_sas fixes megasas_probe_one() to
clear MSI-X flags in kdump when the 'reset_devices' kernel parameter
is passed in.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch for megaraid_sas calls tasklet_schedule() even if
outbound_intr_status == 0 for MFI based boards in MSI-X mode.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Simple conversions to drop flush_scheduled_work() usages in
drivers/scsi. More involved ones will be done in separate patches.
* NCR5380, megaraid_sas: cancel_delayed_work() +
flush_scheduled_work() -> cancel_delayed_work_sync().
* mpt2sas_scsih: drop unnecessary flush_scheduled_work().
* arcmsr_hba, ipr, pmcraid: flush the used work explicitly instead of
using flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds MegaRAID 9265/9285 (Device id 0x5b) specific code
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch adds struct megasas_instance_template changes to
the megaraid_sas driver, and changes all code to use the new instance
entries:
irqreturn_t (*service_isr )(int irq, void *devp);
void (*tasklet)(unsigned long);
u32 (*init_adapter)(struct megasas_instance *);
u32 (*build_and_issue_cmd) (struct megasas_instance *, struct scsi_cmnd *);
void (*issue_dcmd) (struct megasas_instance *instance,
struct megasas_cmd *cmd);
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The following patch modifies the megaraid_sas driver to select the
lowest memory bar available so the driver will work in SR-IOV VF
environments where the memory bar mapping changes.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds MSI-X support and 'msix_disable' module parameter to
the megaraid_sas driver.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
This patch updates the GPL headers in megaraid_sas_base.c and megaraid_sas.h.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch renames megaraid_sas.c to megaraid_sas_base.c to facilitate
other files in the compile.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If fw didn't raise the interrupt with the fw state change to driver
and fw goes to failure state, driver Will check the FW state in
driver's timeout routine and issue the reset if need. Driver will do
the OCR upto three times until kill adapter. Also driver will issue
OCR before driver kill adapter even if fw in operational state.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver add the input parameters support for max_sectors for megaraid
sas gen2 chip. Customer can set the max_sectors support to 1MB for
gen2 chip during the driver load.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver added the Device update flag to tell LSI application driver
whether to do the device Update. LSI MegaRAID SAS application will
check this flag to decide if it needs to update the Device or not.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
To add the Online controller reset support, driver need to do:
a). reset the controller chips -- Xscale and Gen2 which will change
the function calls and add the reset function related to this two
chips.
b). during the reset, driver will store the pending cmds which not
returned by FW to driver's pending queue. Driver will re-issue those
pending cmds again to FW after the OCR finished.
c). In driver's timeout routine, driver will report to OS as reset.
Also driver's queue routine will block the cmds until the OCR
finished.
d). in Driver's ISR routine, if driver get the FW state as state
change, FW in Failure status and FW support online controller
reset (OCR), driver will start to do the controller reset.
e). In driver's IOCTL routine, the application cmds will wait for the
OCR to finish, then issue the cmds to FW.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
It looks like this patch -
commit 7b2519afa1
Author: Yang, Bo <Bo.Yang@lsi.com>
Date: Tue Oct 6 14:52:20 2009 -0600
[SCSI] megaraid_sas: fix 64 bit sense pointer truncation
has caused a problem for 32bit programs with 64bit os -
http://bugzilla.kernel.org/show_bug.cgi?id=15001
fix by converting the user space 32bit pointer to a 64 bit one when
needed.
[jejb: fix up some 64 bit warnings]
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Cc: Bo Yang <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
driver fixed the device update issue after get the AEN PD delete/ADD
and LD add/delete from FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver issue the get ld list to fw to get the logic drive list.
Driver will keep the logic drive list for the internal use after
driver load.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the pad_0 in mfi frame structure to 0 to fix the context value
larger than 32bit value issue.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).
This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the large servers, I/O port resource may not be assigned to all
the PCI devices since it is limited (to 64KB on Intel Architecture[1])
and it may also be fragmented (I/O base register of PCI-to-PCI bridge
will usually be aligned to a 4KB boundary[2]).
If no I/O port resource is assigned to devices, those devices do not
work.
[1] Some machines support 64KB I/O port space per PCI segment.
[2] Some P2P bridges support optional 1KB aligned I/O base.
Therefore, I made a patch for MegaRAID SAS driver to make PCI legacy
I/O port free. I have also tested the patch and it had no problem.
The way to make PCI legacy I/O port free is the same as Fusion-MPT
driver's and it has been merged into 2.6.30.4.
This has already been fixed in e1000 and lpfc.
As a result of the above, the driver can handle its device even when
there are a huge number of PCI devices being used on the system and no
I/O port region assigned to the device.
Signed-off-by: Noriyuki Fujii <n-fujii@np.css.fujitsu.com>
Acked-by: "Yang, Bo" <Bo.Yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
use the constant MEGASAS_RESET_WAIT_TIME when waiting for firmware
commands to complete (currently 3 minutes).
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current sense pointer is cast to a u32 pointer, which can truncate
on 64 bits. Fix by using unsigned long instead.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver will update the OS devices after adding and deleting the device
from FW. When driver receive add or delete AEN from FW, driver will
send the DCMD cmd to get the System PD list from FW. Then driver will
check if this device already in the OS: If add event and OS don't have
the device (but it is in the list), driver add the device to OS,
otherwise driver will not add. If remove event, driver will check the
list, if is not in the list, but OS have the device, driver will
remove the device.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a lock to the skinny firmware initialisation sequence to prevent
the two stage write being non atomic if multiple instances use it.
Add a flag to the driver shutdown sequence to prevent aen ioctls being
called after shutdown begins.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To increase the performance, megaraid sas driver added the IEEE SGE
support to support SAS2 controller.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
MegaRAID SAS2 controller ioctl can't use 32 cmd for applications.
Driver need to divide different number of cmds to IO and application.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
adam radford