This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
First of all it is unnecessary to allocate a new skb in skb_pad since
the existing one is not shared. More importantly, our hard_start_xmit
interface does not allow a new skb to be allocated since that breaks
requeueing.
This patch uses pskb_expand_head to expand the existing skb and linearize
it if needed. Actually, someone should sift through every instance of
skb_pad on a non-linear skb as they do not fit the reasons why this was
originally created.
Incidentally, this fixes a minor bug when the skb is cloned (tcpdump,
TCP, etc.). As it is skb_pad will simply write over a cloned skb. Because
of the position of the write it is unlikely to cause problems but still
it's best if we don't do it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consolidate all usage of ring low water mark to one value.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver will get stuck (permanent transmit timeout), if the transmit
ring size is set too small. It needs to have enough ring elements to
hold one maximum size transmit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Skge driver always causes bad checksums on big-endian.
The checksum in the receive control block was being swapped
when it doesn't need to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Dlink DGE-560T uses Yukon2 chipset so it needs sky2 driver; and
the DGE-530T uses Yukon1 so it uses skge driver.
Bug: http://bugzilla.kernel.org/show_bug.cgi?id=6544
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the problem of some Dlink cards picking the wrong
driver. It looks like these cards use Yukon 1 chipset, not Yukon 2.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't need to keep track of available buffers, it is simpler
to just compute the value (ala e1000). Don't need tes on link up
because should always have available buffers then.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't free transmit buffers until the whole set of transmit descriptors
has been marked as done. Otherwise, we risk freeing a skb before the
whole transmit is done.
This changes the transmit completion handling from incremental to a
two pass algorithm. First pass scans and records the start of the last
done descriptor, second cleans up until that point.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the error case we call skge_rx_reuse twice. This is harmless
but unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver was using dev_alloc_skb which reserves space for the
Ethernet header. This unnecessary and it should just use alloc_skb,
also by using GFP_KERNEL during startup it won't run into problems when
a user asks for a huge ring size or mtu and potentially drains the
reserved atomic pool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver aligns the header on the initial receive buffers, but
but doesn't on followon receive buffer allocations.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reformat some code to make it easier to read. And whitespace
fixes.
Signed-off-by: Stephen Hemminger <sheminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add mmio barriers at the appropriate places, don't have a platform
that needs them, but this is where the documentation of the patch
says to add them.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup of the part of the code that sets up DMA configuration.
Should cause no real change in operation, just clearer.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SysKonnect Genesis and Yukon chip sets have restrictions on the possible
control block area. The memory needs to not cross 4 Gig boundary, and it needs
to be 8 byte aligned. This patch checks and fails to bring the device up
if region is unacceptable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve performance of skge driver by not touching irq mask
register as much. Since the interrupt source auto-masks, the driver
can just leave it disabled until the end of the soft irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup transmit buffers using NAPI. This allows the transmit routine
to leave interrupts enabled, and that improves performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a race between updating the irq mask and setting it
which can be triggered on SMP with a bad cable.
Similar patch from Ingo Molnar and Thomas Gleixner
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
The SysKonnect Genesis based board would fail on initialization
with phy_read errors caused by not waiting for last phy write.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Fix a race in the receive NAPI, irq handling. The interrupt clear and the
start need to be separated. Otherwise there is a window between the last
frame received and the NAPI done level handling.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
This is a clone of John Linville's fixed for speed setting on sky2 driver.
The skge driver has the same code (and bug). It would not allow manually forcing
100 and 10 mbit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There are a couple of problems in the DMA setup code for skge.
* In the 64 bit case, it doesn't set the consistent mask.
* In the 32 bit case, the error check is backwards!
It likely will only be visible as a bug on 64 bit platforms.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
To help in reducing the number of include dependencies, several files were
touched as they were getting needed headers indirectly for stuff they use.
Thanks also to Alan Menegotto for pointing out that net/dccp/proto.c had
linux/dccp.h include twice.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also have to handle out of memory condition on resume.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If changing ring parameters is unable to allocate memory, we need
to return an error and take the device down.
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5715
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Changing the MTU size causes the receiver to have to reallocate buffers.
If this allocation fails, then we need to return an error, and take
the device offline. It can then be brought back up or reconfigured
for a smaller MTU.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change the pause settings doesn't need to cause link to go down/up.
It can be handled by the phy_reset code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change the speed settings doesn't need to cause link to go down/up.
It can be handled by doing the same logic as nway_reset.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Get rid of warning in case of race with ring full and lockless
tx on the skge driver. It is possible to be in the transmit
routine with no available slots and already stopped.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If using UDP over VLAN, with the skge driver there is a possibility
of generating an incorrect checksum. This is a unlikely occurrence
because it is only an issue on Yukon revision 0, and that revision
doesn't seem to exist on any current hardware (probably early prototype).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Increase the driver version number and print version when
probing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use prefetch() in the interrupt path to try and look ahead
at the next place will be looking at in the ring.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Thomas Gleixner