Since commit:
commit f1aa4c541e
Author: Ivo van Doorn <ivdoorn@gmail.com>
Date: Tue Jun 29 21:38:55 2010 +0200
rt2x00: Write the BSSID to register when interface is added
mananged mode in rt2500pci was broken, due to intf->bssid containing
random data rather then the expected 00:00:00:00:00:00
This is corrected by sending the BSSID to rt2x00lib_config_intf
only in AP mode where the bssid is set to a valid value.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The noisefloor array index always corresponds to the rx chain number it
belongs to (with an offset of 3 for the extension chain).
It's much simpler (and actually more correct) to directly use the
chainmask to calculate the bitmask for the noisefloor array, instead of
using these weird chip revision checks and hardcoded mask values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the noisefloor array, the extension channel values start at index 3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the hardware is configured in HT20 mode, noise floor readings for
the extension channel often return invalid values, which keep the
values in the NF history buffer at the hardware-specific maximum limit.
Fix this by discarding the extension channel values when in HT20 mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an aggregation session is being cleaned up, while the tx status
for some frames is being processed, the TID is flushed and its buffers
are sent out.
Unfortunately that left the pending un-acked frames unprocessed, thus
leaking buffers. Fix this by reordering the code so that those frames
are processed first, before the TID is flushed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Negate has precedence over comparison so the original test was always
false. (Neither 0 nor 1 are equal to NL80211_IFTYPE_MONITOR).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes txq state(txq->stopped) can be marked as started but the actual
queue may not be started (in ATH_WIPHY_SCAN state, for example). Fix this.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
snprintf() returns the number of characters that would have been written
(not counting the NUL character). So we can't use it as the limiter to
simple_read_from_buffer() without capping it first at sizeof(buf).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The snprintf() function returns the number of characters that would have
been written (not counting the NUL character on the end). It could
potentially be larger than the size of the buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current practice of checking vif for NULL in one place but not
another seems to confuse some static checkers, smatch in particular.
Since vif will only be NULL in the case of internal scans, adjust the
checks accordingly.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/rtl818x/rtl8180_rtl8225.c
drivers/net/wireless/rtl818x/rtl8180_rtl8225.c:53:33: warning: dubious: x | !y
The existing code is clever and works fine, but it's not worth even a
single line of Sparse warning SPAM...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/wl12xx/wl1251_tx.c
drivers/net/wireless/wl12xx/wl1251_tx.c:118:32: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:118:32: expected unsigned short [unsigned] [usertype] frag_threshold
drivers/net/wireless/wl12xx/wl1251_tx.c:118:32: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:164:24: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:164:24: expected unsigned short [unsigned] [usertype] length
drivers/net/wireless/wl12xx/wl1251_tx.c:164:24: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:166:22: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:166:22: expected unsigned short [unsigned] [usertype] rate
drivers/net/wireless/wl12xx/wl1251_tx.c:166:22: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:167:29: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:167:29: expected unsigned int [unsigned] [usertype] expiry_time
drivers/net/wireless/wl12xx/wl1251_tx.c:167:29: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_tx.c:200:43: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/wl12xx/wl1251_tx.c:200:43: expected restricted __le16 [usertype] fc
drivers/net/wireless/wl12xx/wl1251_tx.c:200:43: got unsigned short [unsigned] [assigned] [usertype] fc
CHECK drivers/net/wireless/wl12xx/wl1251_cmd.c
drivers/net/wireless/wl12xx/wl1251_cmd.c:428:39: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:428:39: expected unsigned int [unsigned] [usertype] rx_config_options
drivers/net/wireless/wl12xx/wl1251_cmd.c:428:39: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:429:39: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:429:39: expected unsigned int [unsigned] [usertype] rx_filter_options
drivers/net/wireless/wl12xx/wl1251_cmd.c:429:39: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:435:29: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:435:29: expected unsigned short [unsigned] [usertype] tx_rate
drivers/net/wireless/wl12xx/wl1251_cmd.c:435:29: got restricted __le16 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:439:47: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:439:47: expected unsigned int [unsigned] [usertype] min_duration
drivers/net/wireless/wl12xx/wl1251_cmd.c:439:47: got restricted __le32 [usertype] <noident>
drivers/net/wireless/wl12xx/wl1251_cmd.c:441:47: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/wl1251_cmd.c:441:47: expected unsigned int [unsigned] [usertype] max_duration
drivers/net/wireless/wl12xx/wl1251_cmd.c:441:47: got restricted __le32 [usertype] <noident>
CHECK drivers/net/wireless/wl12xx/wl1251_boot.c
drivers/net/wireless/wl12xx/wl1251_boot.c:228:22: warning: symbol 'interrupt' shadows an earlier one
/home/linville/git/wireless-next-2.6/arch/x86/include/asm/hw_irq.h:132:13: originally declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"iwlagn: add statistic notification structure for WiFi/BT devices" added
several new '__attribute__ ((packed))' lines. Change them to the
generic __packed.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For edma, we should use DMA_BIDIRECTIONAL, or else use
DMA_FROM_DEVICE.
This is found to address "BUG at arch/x86/mm/physaddr.c:5"
as described here:
http://lkml.org/lkml/2010/7/14/21
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Corey Thomas <coreythomas@charter.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
defines shouldn't be terminated with a
semicolon, the code using them should
supply it. Luckily these are not used
in a context where it matters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since the ibss_beacon variable will only be
filled in the appropriate modes, there's no
reason to be checking the mode again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some devices may have multiple MAC
addresses in their EEPROM, read them
and advertise them to cfg80211.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is only needed in the same
file it is defined in, i.e. iwl-core.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
gcc complains about the firmware loading:
iwl-agn.c: In function ‘iwlagn_load_firmware’:
iwl-agn.c:1860: warning: ‘tlv_len’ may be used uninitialized in this function
iwl-agn.c:1861: warning: ‘tlv_type’ may be used uninitialized in this function
iwl-agn.c:1862: warning: ‘tlv_data’ may be used uninitialized in this function
This is almost correct but we do do break out of the TLV
parsing loop when setting ret. However, the code is hard
to follow, and clearly even the compiler is having issues
with it too.
Additionally, however, the current code is wrong. If there
is a TLV length check error, the code will report
invalid TLV after parsing: ...
because "len" will still be non-zero as we broke out of
the loop.
So to remove the warning and fix that issue, make the code
easier to read by doing length checking with an error label.
As a result, we can completely remove the "ret" variable.
Also, while at it, remove the "fixed_tlv_size" variable
since each TLV type has its own specified length, it just
happens that we have only variable length, flags (0 length)
and u32 TLVs right now. It should still be checked with more
explicit length checks to make it easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Different devices have different size of phy calibration table; add
new TLV to specify the size. If the TLV is not part of uCode header, the
default table size will be used to make sure the backward
compatibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
WiFi/BT combo devices has different statistics notification
structure, adding the support here to make sure the structure
align correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Only WiFi/BT combo devices need to use bluetooth version of statistics
notification; adding the flag in .cfg file to indicate the need for
using different data structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If its WiFi/BT combo device, the statistics notification sent by
uCode will include the additional BT related statistics counters.
Adding new data structure to support the new layout.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
CHECK drivers/net/wireless/b43/main.c
drivers/net/wireless/b43/main.c:111:5: warning: symbol 'b43_modparam_pio' was not declared. Should it be static?
CHECK drivers/net/wireless/b43/phy_g.c
drivers/net/wireless/b43/phy_g.c:975:56: warning: cast truncates bits from constant value (ffff7fff becomes 7fff)
CHECK drivers/net/wireless/b43/phy_lp.c
drivers/net/wireless/b43/phy_lp.c:2701:6: warning: symbol 'b43_lpphy_op_switch_analog' was not declared. Should it be static?
drivers/net/wireless/b43/phy_lp.c:1148:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
drivers/net/wireless/b43/phy_lp.c:1525:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
drivers/net/wireless/b43/phy_lp.c:1529:30: warning: cast truncates bits from constant value (ffff1fff becomes 1fff)
CHECK drivers/net/wireless/b43/wa.c
drivers/net/wireless/b43/wa.c:385:60: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:403:55: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:405:55: warning: cast truncates bits from constant value (ffff00ff becomes ff)
drivers/net/wireless/b43/wa.c:415:71: warning: cast truncates bits from constant value (ffff0fff becomes fff)
AFAICT, none of these amount to real bugs. But this reduces warning
spam from sparse w/o significantly affecting readability of the code (IMHO).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/vhost/net.c
net/bridge/br_device.c
Fix merge conflict in drivers/vhost/net.c with guidance from
Stephen Rothwell.
Revert the effects of net-2.6 commit 573201f36f
since net-next-2.6 has fixes that make bridge netpoll work properly thus
we don't need it disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (24 commits)
bridge: Partially disable netpoll support
tcp: fix crash in tcp_xmit_retransmit_queue
IPv6: fix CoA check in RH2 input handler (mip6_rthdr_input())
ibmveth: lost IRQ while closing/opening device leads to service loss
rt2x00: Fix lockdep warning in rt2x00lib_probe_dev()
vhost: avoid pr_err on condition guest can trigger
ipmr: Don't leak memory if fib lookup fails.
vhost-net: avoid flush under lock
net: fix problem in reading sock TX queue
net/core: neighbour update Oops
net: skb_tx_hash() fix relative to skb_orphan_try()
rfs: call sock_rps_record_flow() in tcp_splice_read()
xfrm: do not assume that template resolving always returns xfrms
hostap_pci: set dev->base_addr during probe
axnet_cs: use spin_lock_irqsave in ax_interrupt
dsa: Fix Kconfig dependencies.
act_nat: not all of the ICMP packets need an IP header payload
r8169: incorrect identifier for a 8168dp
Phonet: fix skb leak in pipe endpoint accept()
Bluetooth: Update sec_level/auth_type for already existing connections
...
The existing code seemed to be somewhat based on the datasheet, but
varied substantially from the vendor-provided driver. This mirrors the
handling of the rtl8185 case from that driver, but still neglects the
specifics for the rtl8180 hardware. Those details are a bit muddled...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/mwl8k.c:1541:21: warning: incorrect type in assignment (different base types)
drivers/net/wireless/mwl8k.c:1541:21: expected restricted __le16 [usertype] result
drivers/net/wireless/mwl8k.c:1541:21: got int
drivers/net/wireless/mwl8k.c:1575:42: expected unsigned short [unsigned] [usertype] cmd
drivers/net/wireless/mwl8k.c:1575:42: got restricted __le16 [usertype] code
drivers/net/wireless/mwl8k.c:1587:50: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1587:50: expected unsigned short [unsigned] [usertype] cmd
drivers/net/wireless/mwl8k.c:1587:50: got restricted __le16 [usertype] code
drivers/net/wireless/mwl8k.c:1592:50: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1592:50: expected unsigned short [unsigned] [usertype] cmd
drivers/net/wireless/mwl8k.c:1592:50: got restricted __le16 [usertype] code
drivers/net/wireless/mwl8k.c:1845:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1845:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1845:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1848:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1848:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1848:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1851:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1851:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1851:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1854:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1854:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1854:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1857:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1857:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1857:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:1860:27: warning: incorrect type in argument 1 (different base types)
drivers/net/wireless/mwl8k.c:1860:27: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/wireless/mwl8k.c:1860:27: got restricted __le32 [usertype] <noident>
drivers/net/wireless/mwl8k.c:3055:20: warning: incorrect type in assignment (different base types)
drivers/net/wireless/mwl8k.c:3055:20: expected restricted __le16 [usertype] ht_caps
drivers/net/wireless/mwl8k.c:3055:20: got unsigned short [unsigned] [usertype] cap
At least the last one looks like a real bug...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
CHECK drivers/net/wireless/rt2x00/rt2x00debug.c
drivers/net/wireless/rt2x00/rt2x00debug.c:193:28: warning: incorrect type in assignment (different base types)
drivers/net/wireless/rt2x00/rt2x00debug.c:193:28: expected restricted __le32 [usertype] chip_rev
drivers/net/wireless/rt2x00/rt2x00debug.c:193:28: got restricted __le16 [usertype] <noident>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CHECK drivers/net/wireless/ipw2x00/libipw_module.c
drivers/net/wireless/ipw2x00/libipw_module.c:65:21: warning: symbol 'libipw_config_ops' was not declared. Should it be static?
drivers/net/wireless/ipw2x00/libipw_module.c:66:6: warning: symbol 'libipw_wiphy_privid' was not declared. Should it be static?
CHECK drivers/net/wireless/ipw2x00/libipw_wx.c
drivers/net/wireless/ipw2x00/libipw_wx.c:415:17: warning: symbol 'ssid' shadows an earlier one
drivers/net/wireless/ipw2x00/libipw_wx.c:324:9: originally declared here
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHECK drivers/net/wireless/ipw2x00/ipw2100.c
drivers/net/wireless/ipw2x00/ipw2100.c:177:28: warning: symbol 'ipw2100_pm_qos_req' was not declared. Should it be static?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k/main.c:282:26: warning: incorrect type in assignment (different base types)
drivers/net/wireless/ath/ath9k/main.c:282:26: expected restricted __le16 [usertype] duration_id
drivers/net/wireless/ath/ath9k/main.c:282:26: got int
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since
commit e1b3ec1a2a
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Mar 29 12:18:34 2010 +0200
mac80211: explicitly disable/enable QoS
mac80211 is telling drivers, in particular
iwlwifi, whether QoS is enabled or not.
However, this is only relevant for station mode,
since only then will any device send nullfunc
frames and need to know whether they should be
QoS frames or not. In other modes, there are
(currently) no frames the device is supposed to
send.
When you now consider virtual interfaces, it
becomes apparent that the current mechanism is
inadequate since it enables/disables QoS on a
global scale, where for nullfunc frames it has
to be on a per-interface scale.
Due to the above considerations, we can change
the way mac80211 advertises the QoS state to
drivers to only ever advertise it as "off" in
station mode, and make it a per-BSS setting.
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
"Recover from tx stall" function is available for all devices except
4965, here add the functionality to 4965.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Smatch complains that "upriv->read_urb" gets dereferenced before
checking for NULL. It turns out that it's possible for
"upriv->read_urb" to be NULL so I added checks around the dereferences.
Also I remove an "if (upriv->bap_buf != NULL)" check because
"kfree(NULL) is OK.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An A-MPDU may contain several subframes each containing its own
CRC for the data. Each subframe also has a respective CRC for the
MPDU length and 4 reserved bits (aka delimeter CRC). AR9003 will
ACK frames that have a valid data CRC but have failed to pass the
CRC for the MPDU length, if and only if the subframe is not the
last subframe in an A-MPDU and if an OFDM phy OFDM reset error has
been caught. Discarding those subframes results in packet loss under
heavy stress conditions, an example being UDP video. Since the
frames are ACK'd by hardware we need to let these frames through
and process them as valid frames.
Cc: Tushit Jain <tushit.jain@atheros.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes this sparse complaint:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c:441:5:
warning: symbol 'ath9k_htc_tx_aggr_oper'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00dev->intf_work workqueue is never initialized when a driver is
probed for a non-existent device (in this case rt2500usb). On such a
path we call rt2x00lib_remove_dev() to free any resources initialized
during the probe before we use INIT_WORK to initialize the workqueue.
This causes lockdep to get confused since the lock used in the workqueue
hasn't been initialized yet but is now being acquired during
cancel_work_sync() called by rt2x00lib_remove_dev().
Fix this by initializing the workqueue first before we attempt to probe
the device. This should make lockdep happy and avoid breaking any
assumptions about how the library cleans up after a probe fails.
phy0 -> rt2x00lib_probe_dev: Error - Failed to allocate device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2027, comm: modprobe Not tainted 2.6.35-rc5+ #60
Call Trace:
[<ffffffff8105fe59>] register_lock_class+0x152/0x31f
[<ffffffff81344a00>] ? usb_control_msg+0xd5/0x111
[<ffffffff81061bde>] __lock_acquire+0xce/0xcf4
[<ffffffff8105f6fd>] ? trace_hardirqs_off+0xd/0xf
[<ffffffff81492aef>] ? _raw_spin_unlock_irqrestore+0x33/0x41
[<ffffffff810628d5>] lock_acquire+0xd1/0xf7
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f06e>] __cancel_work_timer+0xd0/0x17e
[<ffffffff8104f037>] ? __cancel_work_timer+0x99/0x17e
[<ffffffff8104f136>] cancel_work_sync+0xb/0xd
[<ffffffffa0096675>] rt2x00lib_remove_dev+0x25/0xb0 [rt2x00lib]
[<ffffffffa0096bf7>] rt2x00lib_probe_dev+0x380/0x3ed [rt2x00lib]
[<ffffffff811d78a7>] ? __raw_spin_lock_init+0x31/0x52
[<ffffffffa00bbd2c>] ? T.676+0xe/0x10 [rt2x00usb]
[<ffffffffa00bbe4f>] rt2x00usb_probe+0x121/0x15e [rt2x00usb]
[<ffffffff813468bd>] usb_probe_interface+0x151/0x19e
[<ffffffff812ea08e>] driver_probe_device+0xa7/0x136
[<ffffffff812ea167>] __driver_attach+0x4a/0x66
[<ffffffff812ea11d>] ? __driver_attach+0x0/0x66
[<ffffffff812e96ca>] bus_for_each_dev+0x54/0x89
[<ffffffff812e9efd>] driver_attach+0x19/0x1b
[<ffffffff812e9b64>] bus_add_driver+0xb4/0x204
[<ffffffff812ea41b>] driver_register+0x98/0x109
[<ffffffff813465dd>] usb_register_driver+0xb2/0x173
[<ffffffffa00ca000>] ? rt2500usb_init+0x0/0x20 [rt2500usb]
[<ffffffffa00ca01e>] rt2500usb_init+0x1e/0x20 [rt2500usb]
[<ffffffff81000203>] do_one_initcall+0x6d/0x17a
[<ffffffff8106cae8>] sys_init_module+0x9c/0x1e0
[<ffffffff8100296b>] system_call_fastpath+0x16/0x1b
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were a few places where the sc->rxlink pointer was set to NULL "just in
case". This helps nothing - quite to the contrary it is problematic since it
can create self-linked rx descriptors in the middle of the list of receive
buffers.
Here is an example how this could happen (thanks Bob!):
cpu 0: cpu 1:
ath5k_rx_stop
ath5k_tasklet_rx
sc->rxlink = NULL; /* just in case */
// following doesn't link used
// buffer to prev.
ath5k_rxbuf_setup()
In the case of ath5k_rx_stop() and ath5k_stop_locked() buffers/descriptors are
not changed so rxlink should not be changed as well.
In ath5k_intr() we seem to try to work around a hardware bug, as the comment
(which is copied 1:1 from the HAL) suggests. I don't see how this could help.
Also the HAL does not set rxlink in this case (So where does this code come
from? It has been there since the first import of ath5k). Changed to just
increment a statistics counter.
After this patch rxlink is only set to NULL before we initialize rx descriptors
and updated when the descriptors are linked together.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a patch from Bruno Randolf, attempting useful
work while we are resetting the chip just leads to interface
lockups and bad descriptor data, and possibly DMAing to
freed buffers. Let's suspend all tasklets while
reprogramming the registers in the card to avoid such
problems.
In the future we can convert the tasklets to threaded
interrupt handlers to simplify things.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently trigger a reset via a tasklet when certain error
conditions are detected so that the card will (eventually)
restart. Unfortunately this makes locking complicated since
reset can also be called in process context (e.g. for channel
change). Currently nothing protects against concurrent resets,
which can be the source of corruption bugs.
Reset takes too long to spinlock the whole thing, so this
patch moves deferred resets into the mac80211 workqueue to
enable use of sc->lock mutex.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to documentation, The following chip revisions were never sold:
- AR9280 v1.0
- AR9285 v1.0
- AR9285 v1.1
- AR9287 v1.0
Removing initvals specific to these chip revisions saves around 30k in
binary size (tested on MIPS).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must call del_airo_dev() before free_netdev() since we call
add_airo_dev() exactly after alloc_netdev().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k: fix a buffer leak in A-MPDU completion' addressed the
issue of running out of buffers/descriptors in the tx path if a STA is
deleted while tx status feedback is still pending.
The remaining issue is that the skbs of the buffers are not reclaimed,
leaving a memory leak.
This patch fixes this issue by running the buffers through
ath_tx_complete_buf(), ensuring that the pending frames counter is also
updated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_sec_wiphy means max secondary wifis that the driver can accomudate.
So cancelling wiphy work should be based on the presence of
secondary wifis.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove tMinCalPower from ath9k_hw_set_def_power_cal_table(), as it's
never used. Remove corresponding arguments of the functions calculating
that value.
Original patch by Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED should be ON when the radio is put into FULL SLEEP mode during the idle
unassociated state.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"hostap: Protect against initialization interrupt" (which reinstated
"wireless: hostap, fix oops due to early probing interrupt")
reintroduced Bug 16111. This is because hostap_pci wasn't setting
dev->base_addr, which is now checked in prism2_interrupt. As a result,
initialization was failing for PCI-based hostap devices. This corrects
that oversight.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR5008+ and AR9003 currently use two separate implementations of the
ath9k_hw_loadnf function. There are three main differences:
- PHY registers for AR9003 are different
- AR9003 always uses 3 chains, earlier versions are more selective
- The AR9003 variant contains a fix for NF load timeouts
This patch merges the two implementations into one, storing the
register array in the ath_hw struct. The fix for NF load timeouts is
not just relevant for AR9003, but also important for earlier hardware,
so it's better to just keep one common implementation.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Occasionally the hardware can send out tx status information with the wrong
TID. In that case, the BA status cannot be trusted and the aggregate
must be retransmitted.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the receive path gets stuck, a full hardware reset is necessary to
recover from it. If this happens during a scan, the whole scan might fail,
as each channel change bypasses the full reset sequence.
Fix this by resetting the fast channel change flag if stopping the
receive path fails.
This will reduce the number of error messages that look like this:
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x40000020
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PDADC values were only generated for values surrounding the target
index, however not for the target index itself, leading to a minor
error in the generated curve.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9285, the antenna switch configuration register uses more than just
16 bits. Because of an arbitrary mask applied to the EEPROM value that
stores this configuration, diversity was broken in some cases, leading
to a significant degradation in signal strength.
Fix this by changing the callback to return a 32 bit value and remove
the arbitrary mask.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callback functions are gathered in rt2x00dev->ops except
for the callback functions which are used in rt2800lib to
acces rt2800pci/usb.
Move the priv pointer from rt2x00dev to rt2x00dev->ops and
rename it to drv to make it obvious that it is the driver callback
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Large parts of the firmware initialization are shared
between rt2800pci and rt2800usb. Move this code into
rt2800lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rt2x00 uses the TSF_SYNC_BEACON mode for all beaconing
interface types. However, TSF_SYNC_BEACON is meant for IBSS networks and
thus implements TSF merging in the hardware. Rename TSF_SYNC_BEACON to
TSF_SYNC_ADHOC to better express its purpose and introduce the missing
TSF sync mode TSF_SYNC_AP_NONE which should be used for beaconing modes
that don't need TSF merging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Activating the TBTT interrupt when a beacon interval of 0 is configured
results in an interrupt storm causing the machine to hang. Hence,
initialize the beacon interval to a reasonable default of 100TUs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the set_tim callback without managing the DTIM count and the
broad- and multicast buffering in hw, fw or the driver results in wrong
DTIM count values being sent out in beacons. Since all PCI drivers
fetch new beacons periodically and hence get an updated TIM we can just
remove the set_tim callback from these.
The rt2x00 USB drivers don't update the beacon periodically and thus
rely on the set_tim callback to get a correct TIM for beacon
transmission. USB devices still suffer from the DTIM count being wrong
under some circumstances but removing the set_tim callback from these
would cause more harm then good.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use separate mac80211_ops for rt2800pci and rt2800usb in preparation
for further fixes. This shouldn't introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updating the beacon on pre tbtt instead of beacondone allows much lower
latency in regard to TIM updates. Hence, use the pre tbtt interrupt for
updating the beacon in rt2800pci (older devices don't provide a pre tbtt
interrupt).
Also, add a new driver flag to indicate if a driver has pre tbtt support
or not and implement the according behavior in rt2x00lib.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although mac80211 buffers broad- and mutlicast frames for us in AP mode
we still have to send them out after a DTIM beacon. Implement this
behavior by sending out the buffered frames when the beacondone
interrupt is processed.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since all rt2x00 PCI drivers use threaded interrupts now we don't need
to schedule a work just to update the beacon. The only place where the
beacon still gets updated in atomic context is from the set_tim
callback. Hence, move the work scheduling there.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use threaded interrupts for all rt2x00 PCI devices.
This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx
Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_write_beacon is the only function which uses
EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols
in rt2x00 should however use the GPL restricted export.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently vgc_level_reg and vgc_level are equal to eachother,
while the purpose of vgc_level_reg is the value last written
to the register and is remembered through link tuning resets.
The vgc_level is the currently active level, which is
reset during link tuning resets.
The usage of these variables depends on the drivers, some drivers
need both, while others need only one of the two.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.
Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.
This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.
This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Limit the txpower per rate by the approriate values in the eeprom.
This avoids too high txpower values resulting in bad tx performance.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In hostap_add_interface() we do:
sprintf(dev->name, "%s%s", prefix, name);
dev->name has IFNAMSIZ (16) characters.
prefix is local->dev->name.
name is "wds%d"
strlen() returns the number of characters in the string not counting the
NULL so if we have a string with 11 characters we get "12345678901wds%d"
which is 16 characters and a NULL so we're past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We must free priv->eeprom allocated in adm8211_read_eeprom().
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This test is off by one because strlen() doesn't include the NULL
terminator.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes __attribute__ ((packed)) annotations to __packed in wl1271
code that was introduced in a recent patch in wireless-testing.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing "ethtool -s ethX wol X" command configures hostsleep
parameters, but those are activated only during suspend/resume,
there is no way to configure host sleep without actual suspend.
This patch adds debugfs command to enable/disable host sleep based on
already configured host sleep parameters using wol command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we stop the Tx DMA channels, we poll bits 16:31 in
FH_TSSR_RX_STATUS_REG. From 4965 and up, only the bits 16:26 are legal.
Bits 27:31 are not used and are always unset.
Polling them will lead to fail on timeout but since the timeout is quite
small, the stall was not felt.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Intel Wireless WiFi Next Gen AGN support two major categories:
1. Intel Wireless WiFi 4965 AGN device
2. Intel Wireless-N/Advanced-N/Ultimate-N family
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
ucode errors were redefined in new ucode images and all new errors
were showing as advanced sysasserts which was misleading. new errors
are not sequential so additional lookup table added. errors do not
overlap so both are used to support older and newer ucode images.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
To enable 6050 series Gen 2 devices:
1) new PCI_IDs are added;
2) new EEPROM version and calibration version numbers defined;
3) new hardware REV number defined;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We were always using the max transmit power when scanning. Now we use the
values passed to the driver by the mac80211 stack, so that we comply with
regulations.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a complete rewrite of the scanning code. It now includes a
state machine to scan all four possible sets of channels independently:
2.4GHz active, 2.4GHz passive, 5GHz active and 5GHz passive. The wl1271
firmware doesn't allow these sets to be mixed, so up to several scan commands
have to be issued. This patch also allows scanning more than 24 channels per
set, by breaking the sets into smaller parts if needed (the firmware can scan
a maximum of 24 channels at a time).
Previously, the scanning code was erroneously scanning all channels possible
actively, not complying with the CRDA values. This is also fixed with this
patch.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scanning code is going to get a bit more complex, with proper support for
active/passive scans together with 2.4GHz and 5GHz. In the future, also a
new type of scan (periodic scan) will be added. When all this is
implemented, the code is going to be much more complex, so we'd better
separate it into a separate file.
This patch doesn't have any impact on functionality.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 interface to temporarily disable dynamic PS changed, make
corresponding changes to the driver.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch requests mac80211 to disable dynamic PSM based on sense events
coming from the firmware. Effectively, whenever there is bluetooth traffic,
the mac80211 is forced into full PSM mode.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface for hardware ARP configuration changed in the mac80211. Change
driver accordingly.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should read the fem manufacturer value from the NVS, so we can modify it
easily and use a consistent value throughout the configuration. Previously
we had to set the FEM value in the NVS and in the driver's initialization
parameters. This patch removes the latter.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some AP's (such as Zyxel Prestige 600) have totally broken ps-poll
functionality. When powersave is enabled, these AP's will set the TIM bit for
a STA in beacons, but when the STA responds with a ps-poll, the AP does not
respond with data.
The wl1271 firmware is able to send an indication to the host, when this
problem occurs. This patch adds implementation, which temporarily disables
power-save in response to this indication, allowing the AP to transmit whatever
data it has buffered for the STA / whatever data is inbound at that time.
This patch does not make these AP's work reliably in PSM, but improves the
chances of inbound data getting through.
The side effect of this patch is increased power consumption when using a
faulty AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This improves ps-poll handling in WLAN PSM. It also improves performance,
including WLAN-BT co-existence reliability.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the driver to use the ARP configuration function from the
mac80211. Also, clean up IPv6 support from the ACX function as ARP is not
used with that protocol version.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add functionality to pass the current TSF (mac time) to the mac80211. This is
needed for ad-hoc merging.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the calibration performed on the first join command. The
reasoning is that this is unnecessary as devices get their calibration data
via the NVS file, and because the commands break BT coexistence.
This is actually safe, because of the implementation the calibration
was executed on the first JOIN anyway, after an ifdown/ifup the devices have
relied on the NVS for calibration anyway (== most of the time.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (35 commits)
NET: SB1250: Initialize .owner
vxge: show startup message with KERN_INFO
ll_temac: Fix missing iounmaps
bridge: Clear IPCB before possible entry into IP stack
bridge br_multicast: BUG: unable to handle kernel NULL pointer dereference
net: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined
net/ne: fix memory leak in ne_drv_probe()
xfrm: fix xfrm by MARK logic
virtio_net: fix oom handling on tx
virtio_net: do not reschedule rx refill forever
s2io: resolve statistics issues
linux/net.h: fix kernel-doc warnings
net: decreasing real_num_tx_queues needs to flush qdisc
sched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock
qlge: fix a eeh handler to not add a pending timer
qlge: Replacing add_timer() to mod_timer()
usbnet: Set parent device early for netdev_printk()
net: Revert "rndis_host: Poll status channel before control channel"
netfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT
drivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h
...
When ath_tx_complete_aggr() is called, it's responsible for returning
all buffers in the linked list. This was not done when the STA lookup
failed, leading to a race condition that could leak a few buffers when
a STA just disconnected.
Fix this by immediately returning all buffers to the free list in this case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like it might be possible for a TID to be paused, while still
holding some queued buffers, however ath_tx_node_cleanup currently only
iterates over active TIDs.
Fix this by always checking every allocated TID for the STA that is being
cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Changed title, was "wl1251: Use MODULE_ALIAS macro at correct postion
for SPI bus". -- JWL)
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For newer devices (6000g2a and 6000g2b), the sensitivity table send to
uCode require additional table entries to help sensitivity calibration.
All the additional entries has fix data for now, but do expect the value
will be change in the future when device become more stable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Code clean up to change name from having 5000 as part of name which easy
to confuse and think it is for 5000 series devices to more
generic _agn name since it is being used by multiple _agn devices.
No functional changes.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"Flush" request can come from two different sources, it can either from
mac80211, or from device when the operation is needed. Here
adding the support for device issue "flush" request.
When receive tx complete with status is TX_STATUS_FAIL_RFKILL_FLUSH,
issue REPLY_TXFIFO_FLUSH command to uCode to flush out all the tx frames
in queues.
In this condition, since mac80211 has no knowledge of "flush" operation,
driver need to stop all the tx queues and wait for the operation
completed before wake up the queues for frames transmission.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Adding flush callback support in the driver. Two type of flush can be
issued by mac80211:
1. drop = true: frame drop is ok, issue REPLY_TXFIFO_FLUSH host command
to uCode to drop all the frames in tx fifo queues; then return the
control back to mac80211
2. drop = false: wait for either all the frames in tx fifo queues been
transmitted, or timeout; then return the control back to mac80211
If the flush request coming from mac80211, mac80211 will make sure there
are no additional frames push down to driver before flush operation is
completed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When parsing TLV during loading firmware, if encounter any TLV error,
log the error message to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
fw_restart module parameter was broken by the recent check for stuck
queue patch, driver check the fx_restart module parameter
before reload the firmware; but the stuck queue timer kick in after
firmware error and reload the firmware even fw_restart=0. In this case,
driver should not reload the firmware, it is important to help debugging
uCode error.
The only case we can ignore the module parameter is when user request
firmware reload from debugfs, which can bypass the checking and perform
firmware reload all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Commit eed8e22f01 added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.
The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/rt2x00/rt2800lib.o
drivers/net/wireless/rt2x00/rt2800lib.c: In function 'rt2800_ampdu_action':
drivers/net/wireless/rt2x00/rt2800lib.c:2821: warning: unused variable 'rt2x00dev'
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Latest rt2870 legacy driver also sets BBP_CSR_CFG_BBP_RW_MODE to 1
when reading or writing the EEPROM. This means we can make the
BBP reading and writing completely equal on all platforms.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy driver indicates that BBP1_TX_ANTENNA must be set
to 0 for TXPATH values of 1 and 3. So the previous statement
that nothing should be done for TXPATH = 3, is false.
Furthermore, remove the false BBP3_RX_ANTENNA initialization
when TXPATH is 1 for PCI and SOC devices. This field will always
be overridden in the next switch statement, making this initialization
bogus. History of this line indicates it was there from the beginning,
and was once caught as typo. Instead of replacing the line with the
correct line, the correct line was added...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_HT_CAP_RX_STBC is a 2 bit flag, and should thus
never be set as normal flag. Instead we must read the number
of RX paths from the EEPROM and set the IEEE80211_HT_CAP_RX_STBC
with the correct value (using the same logic as the number of TX
streams).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is removed the according beacon entry should be reset.
The current approach to only clear the first word is not enough to stop
the device from sending out the beacon, hence resulting in beacons being
sent out for already removed interfaces.
Fix this by invalidating the entire TXWI in front of the beacon instead
of only the first word.
Also clear all beacons during startup in the same way.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the link tuning is based on average RSSI values taken from all received
frames it doesn't make sense to enable it in AP mode where every associated
station provides independent RSSI values. Furthermore the legacy drivers
don't enable link tuning in AP mode as well.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rt61pci beacon updates in the same way as rt2800pci. rt61pci didn't
update the beacon template after each beacon interval, resulting in the
DTIM count being incorrect (if DTIM period > 1). Fix this by calling
rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci didn't update the beacon template after each beacon interval,
resulting in the DTIM count being incorrect (if DTIM period > 1). Fix this
by calling rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAC_BSSID_DW1_BSS_ID_MASK must be set to the mask 3, to
enable 8 BSSID's. The MAC_BSSID_DW1_BSS_BCN_NUM is initialized
to 7 to enable the 8 beacons.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align with the latest versions of the Ralink legacy driver(s).
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville