Makes more sense to have randomly generated address by default than to
have all zeroes. It also allows user to for example put the bond into
bridge without need to have any slaves in it.
Also note that this changes only behaviour of bonds with no slaves. Once
the first slave device is enslaved, its address will be used (no change
here).
Also, fix dev_assign_type values on the way.
Reported-by: Pavel Šimerda <psimerda@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case vring setup with the firmware failed,
success status was returned. fix it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware crash on attempt to delete Rx chain.
Driver part of Rx chain removed only in preparation for the target reset;
as reset is the only flow that removes Rx chain in the firmware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable interrupts first to prevent spurious WMI events arrival
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connect times out, scan was not re-enabled.
Strictly say, it is firmware issue - it should issue "disconnect"
event but it does not. Compensate in the driver.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other parts of Rx path (BACK logic) will need to access associated data
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to multi-tx-queue design, wil_start_xmit() used to be executed
concurrently for different queues. Then, these transmits delivered
to the same queue, creating race.
As result, Tx descriptor may be skipped, causing stall in hardware.
Convert to single Tx queue fixes it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows to account for Tx errors
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move WMI related operations to wmi.c as helper functions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce debug category "MISC", convert all raw wil_dbg() to this category.
This improves dynamic debug manageability
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make printings from IRQ appears in dmesg in chronological order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the firmware, added is ability to report internal errors using IRQ.
Catch this IRQ and notify user space via netlink
User space get notified like (udevadm monitor --kernel --property):
KERNEL[12660.320520] change /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net)
ACTION=change
DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12
DEVTYPE=wlan
EVENT=FW_ERROR
IFINDEX=6
INTERFACE=wlan12
SEQNUM=2489
SOURCE=wil6210
SUBSYSTEM=net
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the array indexes are in-bounds before accessing the rate2 and tmp
arrays.
Found with the following semantic patch:
<smpl>
@@
identifier t;
identifier idx;
expression E;
statement S;
@@
* for (... ; <+... t[idx] ...+> && idx < E ; ...)
S
</smpl>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix:
drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’:
drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but
not used [-Wunused-but-set-variable]
seen when building allmodconfig on x86_64 with W=1 by removing the unused
variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on "iwlwifi: fix antenna bitmask".
(362b0563b2)
Like the new iwlagn devices, the old 4965N device only
supports a maximum of three antennas. Hence only three
bits are used, the fourth bit is likely the A-MPDU
indicator.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of converting it to a bogus error code -1, we should
return the original error code from lower layer driver. This
error code will be printed so it may give user some clues on
what has happened.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If pci_iomap() fails in mwifiex_pcie_init(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While using STA mode in the AP firmware, avoid
calling some firmware commands which are not
supported by the AP firmware.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose interface specific function calls
based on interface type instead of
firmware types.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and delete self entry in the firmware sta database
for AP interface only. We do not need such an entry for
STA interface.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware supports hardware encryption feature
for the station interface running on AP
firmware.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set mac type for station interface on AP firmware
as secondary. This allows the firmware to set specific
characteristics for the STA interface.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When user wants to add a station interface when
AP firmware is loaded & in-use, allow creating
it and also notify user about the same.
Allow adding max one STA interface for AP fw.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specify the STA support in iface_limit and
in wihpy->interface_modes
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids calling mwl8k_cmd_rf_antenna functions every
time mwl8k_config function is called.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the commands, that might change the hw characteristics
of the PHY device, stop the running bsses and resume them
once command is complete.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow AP and Mesh mode to operate concurrently using
single radio. Verify this using fonera 2.0n featuring
RT3052 chipset and also TP-LINK TL-WN727N featuring
RT5370 chipset.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemal.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use this macro only on 3 places - remove it and replace by other
appropriate macros for printing messages.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those messages can flood in dmesg, so do not print them by default.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some messages provide useful information, but are disabled without
CONFIG_RT2X00_DEBUG=y, so enable them by default
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sample data received through the spectral scan can be either in big or
little endian byteorder. This information isn't stored in the output file.
Therefore it is not possible for the analyzer software to find the correct byte
order.
It is relative common to get the data from a low end AP in big endian mode and
transfer it to another computer in little endian mode to analyze it. Therefore,
it would be better to store it in network (big endian) byte order.
The extension of the 8 bit bins for each bin to 16 bit is not necessary. This
operation can be done in userspace or on a different machine. Instead the
max_exp defining the amount of shifting required for each bin is exported to
userspace.
The change of the output format requires a change of the type in the sample
tlv to allow the userspace program to correctly detect the bin format.
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[siwu@hrz.tu-chemnitz.de: squashed patches, update commit message, rebase, fix endianess bug]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the spectral scan feature, frames with phy errors are
returned for further processing to the driver. However, if the frames
also have an invalid CRC (which seems to happen quite often), the frame
is marked with bad CRC and not with the PHY error bit. The FFT
processing function will thus miss the frames.
Fix this by changing the precedence in error marking.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spectral packets are "bogus" packets and should not be further evaluated
by the RX path.
Statistics are added to keep track of these packets.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export the various parameters to userspace.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes invalid access of RxBD ring buffer descriptor's
length and flag inside PCIe send_data_complete() routine. We are
supposed to modify TxBD buffer descriptor's length and flag here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete successive tests to the same location. This looks like simple code
duplication.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.
If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.
We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state. Correct this by
setting netif_carrier_off on probe, like other drivers do.
Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway
Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bonding module is loaded with primary parameter and one decides to unset
primary slave using sysfs these settings are not preserved during bond device
restart. Primary slave is only unset once and it's not remembered in
bond->params structure. Below is example of recreation.
grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=active-backup miimon=100 primary=eth01"
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)
echo "" > /sys/class/net/bond0/bonding/primary
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0
grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond
BONDING_OPTS="mode=active-backup miimon=100 "
ifdown bond0 && ifup bond0
without patch:
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)
with patch:
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Milos Vyletel <milos.vyletel@sde.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forbid polling, writing and reading when the file were detached, this may
complex the user in several cases:
- when guest pass some buffers to vhost/qemu and then disable some queues,
host/qemu needs to do its own cleanup on those buffers which is complex
sometimes. We can do this simply by allowing a user can still write to an
disabled queue. Write to an disabled queue will cause the packet pass to the
kernel and read will get nothing.
- align the polling behavior with macvtap which never fails when the queue is
created. This can simplify the polling errors handling of its user (e.g vhost)
We can simply achieve this by don't assign NULL to tfile->tun when detached.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c8d68e6be1 removed carrier off call
from tun_detach since it's now called on queue disable and not only on
tun close. This confuses userspace which used this flag to detect a
free tun. To fix, put this back but under if (clean).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove unused members(!): imask, ievent
* move space consuming interrupt name strings (int_name_* members) to
external structures, unessential for the driver's hot path
* keep high priority hot path data within the first 2 cache lines
This reduces struct gfar_priv_grp from 6 to 3 cache lines.
(Also fixed checkpatch warnings for the old code, in the process.)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out redundant code (improve readability, source code size).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resize and regroup structure members to eliminate memory holes and
to pack the structure into 2 cache lines (from 3).
tx_ring_size was resized from 4 to 2 bytes and few members were re-grouped
in order to eliminate byte holes and achieve compactness.
Where possible, few members were grouped according to their usage and access
order (i.e. start_xmit vs. clean_tx_ring members), less important members
were pushed at the end.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the format of ethoc.c to meet network driver style as
per checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
just as it should have been. It also helps
removing the, now unnecessary, workqueue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use ndo_get_stats64 to get 64bit statistics.
Signed-off-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of changes:
.Newly added phys
-KSZ8081/KSZ8091, which has some phy ids.
-KSZ8061
-KSZ9031, which is Gigabit phy.
-KSZ886X, which has a switch function.
-KSZ8031, which has a same phy ids with KSZ8021.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal driver to manage the
Realtek RTL8211E 10/100/1000 Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Included is an NFC pull. Samuel says:
"It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Also included are a pair of mac80211 pulls. Johannes says:
"We found two bugs in the previous code, so I'm sending you a pull
request again this soon.
This contains two regulatory bug fixes, some of Thomas's hwsim beacon
timer work and a documentation fix from Bob."
"Another pull request for mac80211-next. This time, I have a number of
things, the patches are mostly self-explanatory. There are a few fixes
from Felix and myself, and random cleanups & improvements. The biggest
thing is the partial patchset from Marco preparing for mesh powersave."
Additionally, there are a pair of iwlwifi pulls. Johannes says:
"For iwlwifi-next, I have a few cleanups/improvements as well as a few
not very important fixes and more preparations for new devices."
"Please pull a few updates for iwlwifi. These are just some cleanups and
a debug improvement."
On top of that, there is a slew of driver updates. This includes
brcmfmac, mwifiex, ath9k, carl9170, and mwl8k as well as a handful
of others. The bcma and ssb busses get some attention as well.
Still, I don't see any big headliners here.
Also included is a pull of the wireless tree, in order to resolve
some merge conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000e, ixgbevf, igb and igbvf.
Majority of the patches are code cleanups of e1000e where code
is removed (Yeah!). The other two e1000e patches are fixes. The
first is to fix the maximum frame size for 82579 devices. The second
fix is to resolve an issue with devices other than 82579 that suffer
from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.
The ixgbevf patch is to ensure that the driver fetches the correct,
refreshed value for link status and speed when the values have changed.
The igb and igbvf patches are a solution to an issue Stefan Assmann
reported, where when the PF is up and igbvf is loaded, the MAC address
is not generated using eth_hw_addr_random().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Added accessor and skb_reserve helpers for struct can_skb_priv.
Removed pointless skb_headroom() check.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:
[ 588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[ 588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[ 588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[ 588.286208] ieee80211 phy0: Hardware restart was requested
The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.
Bisecting was done by Seth Forshee and showed following commit as the
culprit:
commit 57fe504817
Author: Piotr Haber <phaber@broadcom.com>
Date: Wed Nov 28 21:44:07 2012 +0100
brcmsmac: fix bounds checking in tx/rx
[1] http://www.spinics.net/lists/linux-wireless/msg101293.html
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tighten up some of the code surrounding MAC addresses. Since the PF is
now giving all zeros instead of a random address, check for this case
and generate a random address. This ensures that we always know when we
have a random address and udev won't get upset about it.
Additionally, tighten up some of the log messages and clean up the
formatting.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change makes it necessary to set get_link_status to ensure that
the driver fetches the correct, refreshed value for link status and speed
when it has changed in the physical function device.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was removed but the applicable comments were not.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary #include, forward prototype of struct e1000_adapter and
an empty comment; fix a comment which mentions "static data for the MAC"
which is not applicable to the following struct; and cleanup some
whitespace issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All references to E1000_ERT_2048 have been removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this. To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call. The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pravin Shelar mentioned that GSO could potentially generate
wrong TX checksum if skb has fragments that are overwritten
by the user between the checksum computation and transmit.
He suggested to linearize skbs but this extra copy can be
avoided for normal tcp skbs cooked by tcp_sendmsg().
This patch introduces a new SKB_GSO_SHARED_FRAG flag, set
in skb_shinfo(skb)->gso_type if at least one frag can be
modified by the user.
Typical sources of such possible overwrites are {vm}splice(),
sendfile(), and macvtap/tun/virtio_net drivers.
Tested:
$ netperf -H 7.7.8.84
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
7.7.8.84 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3959.52
$ netperf -H 7.7.8.84 -t TCP_SENDFILE
TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.8.84 ()
port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3216.80
Performance of the SENDFILE is impacted by the extra allocation and
copy, and because we use order-0 pages, while the TCP_STREAM uses
bigger pages.
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. There is are 9 patches by
Fabio Baltieri and Kurt Van Dijck which add LED infrastructure and
support for CAN devices. Bernd Krumboeck adds a driver for the USB CAN
adapter from 8 devices. Oliver Hartkopp improves the CAN gateway
functionality. There are 4 patches by me, which clean up the CAN's
Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
filters_lock might have been used while it was re-initialized.
Moved filters_lock and filters_list initialization to init_netdev instead of
alloc_resources which is called every time the device is configured.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 (success) when in fact we are aborting the load, leads to kernel
panic when unloading the module. Fix that by returning the actual error code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device multicast list is protected by netif_addr_lock_bh in the networking core, we should
use this locking practice in mlx4_en too.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is stopped and flow steering mode is not device managed: promisc QP
rule wasn't removed from MCG table.
Added code to remove it in all flow steering modes.
In addition, promsic rule removal should be in stop port and not in start
port - moved it accordingly.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing the DUMP_ETH_STATS firmware command outside the lock leads to kernel
panic when data structures such as RX/TX rings are freed in parallel, e.g when
one changes the mtu or ring sizes.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9992c2e (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant. The USB core has already done the lookup
and saved the result in the USB interface struct. Use that
instead.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used. A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...and cleanup some whitespace in other prototypes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver has been converted to use extended descriptors instead of
the older legacy descriptor type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults. This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the i217 and i218 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register. Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
John W. Linville says:
====================
This is a batch of fixes intende for the 3.8 stream.
Regarding the iwlwifi bits, Johannes says this:
"Please pull to get a single fix from Emmanuel for a bug I introduced due
to misunderstanding the code."
Regarding the mac80211 bits, Johannes says this:
"I have a few small fixes for you:
* some mesh frames would cause encryption warnings -- fixes from Bob
* scanning would pretty much break an association if we transmitted
anything to the AP while scanning -- fix from Stanislaw
* mode injection was broken by channel contexts -- fix from Felix
* FT roaming was broken: hardware crypto would get disabled by it"
Along with that, a handful of other fixes confined to specific drivers.
Avinash Patil fixes a typo in a NULL check in mwifiex.
Larry Finger fixes a build warning in rtlwifi. Seems safe...
Stanislaw Gruszka fixes iwlegacy to prevent microcode errors when
switching from IBSS mode to STA mode.
Felix Fietkau provides a trio of ath9k fixes related to proper tuning.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Greear reported crashes in ip_rcv_finish() on a stress
test involving many macvlans.
We tracked the bug to a dst use after free. ip_rcv_finish()
was calling dst->input() and got garbage for dst->input value.
It appears the bug is in loopback driver, lacking
a skb_dst_force() before calling netif_rx().
As a result, a non refcounted dst, normally protected by a
RCU read_lock section, was escaping this section and could
be freed before the packet being processed.
[<ffffffff813a3c4d>] loopback_xmit+0x64/0x83
[<ffffffff81477364>] dev_hard_start_xmit+0x26c/0x35e
[<ffffffff8147771a>] dev_queue_xmit+0x2c4/0x37c
[<ffffffff81477456>] ? dev_hard_start_xmit+0x35e/0x35e
[<ffffffff8148cfa6>] ? eth_header+0x28/0xb6
[<ffffffff81480f09>] neigh_resolve_output+0x176/0x1a7
[<ffffffff814ad835>] ip_finish_output2+0x297/0x30d
[<ffffffff814ad6d5>] ? ip_finish_output2+0x137/0x30d
[<ffffffff814ad90e>] ip_finish_output+0x63/0x68
[<ffffffff814ae412>] ip_output+0x61/0x67
[<ffffffff814ab904>] dst_output+0x17/0x1b
[<ffffffff814adb6d>] ip_local_out+0x1e/0x23
[<ffffffff814ae1c4>] ip_queue_xmit+0x315/0x353
[<ffffffff814adeaf>] ? ip_send_unicast_reply+0x2cc/0x2cc
[<ffffffff814c018f>] tcp_transmit_skb+0x7ca/0x80b
[<ffffffff814c3571>] tcp_connect+0x53c/0x587
[<ffffffff810c2f0c>] ? getnstimeofday+0x44/0x7d
[<ffffffff810c2f56>] ? ktime_get_real+0x11/0x3e
[<ffffffff814c6f9b>] tcp_v4_connect+0x3c2/0x431
[<ffffffff814d6913>] __inet_stream_connect+0x84/0x287
[<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
[<ffffffff8108d695>] ? _local_bh_enable_ip+0x84/0x9f
[<ffffffff8108d6c8>] ? local_bh_enable+0xd/0x11
[<ffffffff8146763c>] ? lock_sock_nested+0x6e/0x79
[<ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
[<ffffffff814d6b49>] inet_stream_connect+0x33/0x49
[<ffffffff814632c6>] sys_connect+0x75/0x98
This bug was introduced in linux-2.6.35, in commit
7fee226ad2 (net: add a noref bit on skb dst)
skb_dst_force() is enforced in dev_queue_xmit() for devices having a
qdisc.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a cpu notifier to virtio-net, so that we can reset the
virtqueue affinity if the cpu hotplug happens. It improve
the performance through enabling or disabling the virtqueue
affinity after doing cpu hotplug.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split out the clean affinity function to virtnet_clean_affinity().
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Michael mentioned, set affinity and select queue will not work very
well when CPU IDs are not consecutive, this can happen with hot unplug.
Fix this bug by traversal the online CPUs, and create a per cpu variable
to find the mapping from CPU to the preferable virtual-queue.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Providing communication channel between KVM and e-Switch so that it
can be informed when hypervisor configures a MAC address and VLAN.
qlcnic_mac_learn module param usage will be changed to:
0 = MAC learning is disable
1 = Driver learning is enable
2 = FDB learning is enable
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide port number in command payload for LED/Beaconing tests.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Some adapter types do not support co-existence of Legacy Interrupt with
MSI-x or MSI among multiple functions. For those adapters, prevent attaching
to a function during normal load, if MSI-x or MSI vectors are not available.
o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in
legacy mode for all functions in the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The struct can_skb_priv is used to transport additional information along
with the stored struct can(fd)_frame that can not be contained in existing
struct sk_buff elements.
can_skb_priv is located in the skb headroom, which does not touch the existing
CAN sk_buff usage with skb->data and skb->len, so that even out-of-tree
CAN drivers can be used without changes.
Btw. out-of-tree CAN drivers without can_skb_priv in the sk_buff headroom
would not support features based on can_skb_priv.
The can_skb_priv->ifindex contains the first interface where the CAN frame
appeared on the local host. Unfortunately skb->skb_iif can not be used as this
value is overwritten in every netif_receive_skb() call.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on usb_8dev devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on sja1000 devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on mcp251x devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on c_can devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on ti_hecc devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Anant Gole <anantgole@ti.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on at91_can devices by
calling appropriate can_led functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for canbus activity led indicators on flexcan devices by
calling appropriate can_led_* functions.
These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The LED trigger name for CAN devices is based on the initial
CAN device name, but does never change. The LED trigger name
is not guaranteed to be unique in case of hotplugging CAN devices.
This patch tries to address this problem by modifying the
LED trigger name according to the CAN device name when
the latter changes.
v1 - Kurt Van Dijck
v2 - Fabio Baltieri
- remove rename blocking if trigger is bound
- use led-subsystem function for the actual rename (still WiP)
- call init/exit functions from dev.c
v3 - Kurt Van Dijck
- safe operation for non-candev based devices (vcan, slcan)
based on earlier patch
v4 - Kurt Van Dijck
- trivial patch mistakes fixed
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In net_device notifier calls, it was impossible to determine
if a CAN device is based on candev in a safe way.
This patch adds such test in order to access candev storage
from within those notifiers.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the functions to add two LED triggers, named
<ifname>-tx and <ifname>-rx, to a canbus device driver.
Triggers are called from specific handlers by each CAN device driver and
can be disabled altogether with a Kconfig option.
The implementation keeps the LED on when the interface is UP and blinks
the LED on network activity at a configurable rate.
This only supports can-dev based drivers, as it uses some support field
in the can_priv structure.
Supported drivers should call devm_can_led_init() and can_led_event() as
needed.
Cleanup is handled automatically by devres, so no *_exit function is
needed.
Supported events are:
- CAN_LED_EVENT_OPEN: turn on tx/rx LEDs
- CAN_LED_EVENT_STOP: turn off tx/rx LEDs
- CAN_LED_EVENT_TX: trigger tx LED blink
- CAN_LED_EVENT_RX: trigger tx LED blink
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add device driver for USB2CAN interface from "8 devices" (http://www.8devices.com).
changes since v10:
* small cleanups
changes since v9:
* fixed syslog messages
* fixed crc error number
* increased MAX_RX_URBS and MAX_TX_URBS
changes since v8:
* remove all sysfs files
changes since v7:
* add sysfs documentation
* fix minor styling issue
* fixed can state for passive mode
* changed handling for crc errors
changes since v6:
* changed some variable types to big endian equivalent
* small cleanups
changes since v5:
* unlock mutex on error
changes since v4:
* removed FSF address
* renamed struct usb_8dev
* removed unused variable free_slots
* replaced some _to_cpu functions with pointer equivalent
* fix return value for usb_8dev_set_mode
* handle can errors with separate function
* fix overrun error handling
* rewrite error handling for usb_8dev_start_xmit
* fix urb submit in usb_8dev_start
* various small fixes
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds an 'if CAN...endif' Block around all CAN symbols in
net/can/Kconfig. So the 'depends on CAN' dependencies can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The iwl-op-mode.h file uses a struct dentry for debugfs
so should include debugfs.h.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the pages are to be used by front-end, it may need
to know the page order, provide it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit f590dcec94
which has been reported to cause issues.
See https://lkml.org/lkml/2013/1/20/4 for further details.
Cc: stable@vger.kernel.org [3.7]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The X540 can link at 100Mbps - fix the link speed indicator message to
show that value.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63. Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for enable/disable of SR-IOV via the PCI sysfs interface
move some core SR-IOV enablement code that would be common to module
parameter usage or callback from the PCI bus driver to a separate
function so that it can be used by either method.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally. Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to inline the Rx PTP descriptor handling. The main
motivation is to avoid unnecessary jumps into function calls that we then
immediately exit because we are not performing timestamps.
The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU
utilization in my performance runs to 0%, and the only value tested is the Rx
descriptor which should already be warm in the cache if not stored in a
register.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.
This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.
To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.
If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the comment on ptp_overflow_check to match up with what is
currently used as the parameters. Also change the jiffies check to use
time_is_after_jiffies macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the filters for ethtool's get_ts_info to return support for
all filters which can be supported by upscaling to ptp_v2_event. The intent
behind this change is due to reasoning that we do in fact support the
filters. (hwtstamp_ioctl returns success after setting the filter to the
upscaled version). In this way we can remain consistent over which filters are
supported via the get_ts_info ioctl and which filters are in practice actually
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the ethtool diagnostics test by ensuring that the tests
work properly regardless of what state the adapter was in. The SRIOV VF check is
done at the beginning, forgoing the link test. The if_running -> dev_close is
moved before the link test, as well as a call to enable the Tx laser. This
ensures that the link test will return valid results even when adapter was
previously down. Also, a call to disable the Tx laser is added if the device
was down before the start. This ensures consistent behavior of the Tx laser
before and after the diagnostic checks. The end result is consistent behavior
regardless of device state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When posting a message on the bulletin board, the PF calculates crc
over the message and places the result in the message. When the VF
samples the Bulletin Board it copies the message aside and validates
this crc. The length of the message is crucial here and must be the
same in both parties. Since the PF is running in the Hypervisor and
the VF is running in a Vm, they can possibly be of different versions.
As the Bulletin Board is designed to grow forward in future versions,
in the VF the length must not be the size of the message structure
but instead it should be a field in the message itself.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823e1d9 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set.
Fixes compilation by moving function declarations between header files.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In INTA mode, cnic and bnx2x share the same IRQ. During chip reset,
for example, cnic will stop servicing IRQs after it has shutdown the
cnic hardware resources. However, the shared IRQ is still active as
bnx2x needs to finish the reset. There is a window when bnx2x does
not know that cnic is no longer handling IRQ and things don't always
work properly.
Add a flag to tell bnx2x that cnic is handling IRQ. The flag is set
before the first cnic IRQ is expected and cleared when no more cnic
IRQs are expected, so there should be no race conditions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an incorrect SR-IOV memory release which was committed in 1ab4434.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't unload the bnx2x driver if its in a recovery process, or if
the previous load have failed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 15192a8cf there have been a memory leak upon rmmod
of the bnx2x driver.
This corrects the memory leak and corrects the zeroing of internal
memories upon driver load.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing 57712_VF and 57800_VF to CHIP_IS_E2 and CHIP_IS_E3
macros (missing from commit 8395be5).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add/Revise several debug prints in the bnx2x driver - on regular flows
as well as error flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the incorrect usage of `usleep_range(1000, 1000)' into
`usleep_range(1000, 2000)'.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly changes the bnx2x code without `true' functional changes.
Changes include:
1. Gathering macros into a single macro when combination is used multiple
times.
2. Exporting parts of functions into their own functions.
3. Return values after if-else instead of only on the else condition
(where current flow would simply return same value later in the code)
4. Removing some unnecessary code (either dead-code or incorrect conditions)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly corrects white spaces, indentations, and comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reactivate promiscuous mode in H/W upon gfar_init_mac(), if the
net dev requires it (IFF_PROMISC flag set).
This way the promisc mode is preserved accross device reset conditions
like tx timeout, device restore, a.s.o.
Signed-off-by: Voncken C Acksys <cedric.voncken@acksys.fr>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in commit 6dccd16 "r8169: merge with version
6.001.00 of Realtek's r8169 driver". I did not find the version
6.001.00 online, but in 6.002.00 or any later r8169 from Realtek
this hunk is no longer present.
Also commit 05af214 "r8169: fix Ethernet Hangup for RTL8110SC
rev d" claims to have fixed this issue otherwise.
The magic compare mask of 0xfffe000 is dubious as it masks
parts of the Reserved part, and parts of the VLAN tag. But this
does not make much sense as the VLAN tag parts are perfectly
valid there. In matter of fact this seems to be triggered with
any VLAN tagged packet as RxVlanTag bit is matched. I would
suspect 0xfffe0000 was intended to test reserved part only.
Finally, this hunk is evil as it can cause more packets to be
handled than what was NAPI quota causing net/core/dev.c:
net_rx_action(): WARN_ON_ONCE(work > weight) to trigger, and
mess up the NAPI state causing device to hang.
As result, any system using VLANs and having high receive
traffic (so that NAPI poll budget limits rtl_rx) would result
in device hang.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create new flow caches when a new flow is identified by tuntap, This may lead
some issues:
- userspace may produce a huge amount of short live flows to exhaust host memory
- the unlimited number of flow caches may produce a long list which increase the
time in the linear searching
Solve this by introducing a limit of total number of flow caches.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A MAX_TAP_QUEUES(1024) queues of tuntap device is always allocated
unconditionally even userspace only requires a single queue device. This is
unnecessary and will lead a very high order of page allocation when has a high
possibility to fail. Solving this by creating a one queue net device when
userspace only use one queue and also reduce MAX_TAP_QUEUES to
DEFAULT_MAX_NUM_RSS_QUEUES which can guarantee the success of
the allocation.
Reported-by: Dirk Hohndel <dirk@hohndel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reverting 328d7b8 and instead adding an exception for the
Sierra Wireless MC7710.
commit 328d7b8 (net: cdc_mbim: send ZLP after max sized NTBs)
added a workaround for an issue observed on one specific device.
Concerns were raised that this workaround adds a performance
penalty to all devices based on questionable, if not buggy,
behaviour of a single device:
"If you add ZLP for NTBs of dwNtbOutMaxSize, you are heavily affecting CPU
load, increasing interrupt load by factor of 2 in high load traffic
scenario and possibly decreasing throughput for all other devices
which behaves correctly."
"The idea of NCM was to avoid extra ZLPs. If your transfer is exactly
dwNtbOutMaxSize, it's known, you can submit such request on the receiver
side and you do not need any EOT indicatation, so the frametime can be
used for useful data."
Adding a device specific exception to prevent the workaround from
affecting well behaved devices.
The assumption here is that needing a ZLP is truly an *exception*.
We do not yet have enough data to verify this. The generic
workaround in commit 328d7b8 should be considered acceptable despite
the performance penalty if the exception list becomes a maintainance
hassle.
Cc: Alexey ORISHKO <alexey.orishko@stericsson.com>
Cc: Yauheni Kaliuta <y.kaliuta@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is useful to be able to change the MAC address of the
interface for netback devices. For example, when using ebtables it may
be useful to be able to distinguish traffic from different interfaces
without depending on the interface name.
Reported-by: Nikita Borzykh <sample.n@gmail.com>
Reported-by: Paul Harvey <stockingpaul@hotmail.com>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xen.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Matt Wilson <msw@amazon.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is kept per-channel, so removing unnecessary (or constant) fields from
it can save quite a bit of memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are no longer needed for ANI functionality
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dropping packets from aggregation sessions is usually not a good idea, as
it might upset the synchronization of the BlockAck receive window of the
remote node. The use of the retry_tx parameter to reset/tx-drain functions
also seemed a bit arbitrary.
This patch removes this parameter altogether and ensures that pending tx
frames are not dropped for no good reason.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completing frame transmission can fail if the rx engine is stopped
prematurely, as the hw might be waiting for an ACK from the other side.
Shutting down tx before rx might make the DMA shutdown more reliable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of variable packet_beacon might be uninitialized in the three files.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hardware is not ready, il4965_pci_probe() breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If pci_iomap() fails in mwl8k_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
There is a similar issue when priv->rxd_ops is NULL in mwl8k_probe_hw().
The patch adds proper error code return values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AP responds with appropriate status code, we forward that
code correctly to cfg80211. But sometimes when there is no
response from AP, our firmware uses proprietary status codes.
We will map authentication timeout to WLAN_STATUS_AUTH_TIMEOUT
and other proprietary codes to WLAN_STATUS_UNSPECIFIED_FAILURE.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since rt2800 hardware isn't capable of reporting the TX status of
BlockAckReq frames implement the TX status handling of BARs in
rt2x00lib. We keep track of all BARs that are send out and try to
match incoming BAs to the appropriate BARs. This allows us to report a
more or less accurate TX status for BAR frames which in turn improves
BA session stability.
This is loosley based on Christian Lamparter's patch for carl9170
"carl9170: fix HT peer BA session corruption".
We have to walk the list of pending BARs for every rx'red BA even
though most BAs don't belong to any of these BARs as they are just
acknowledging an AMPDU. To keep that overhead low use RCU which allows
us to walk the list of pending BARs without the need to acquire a lock.
This however requires us to _copy_ relevant information from the BAR
(RA, TA, control field, start sequence number) into our BAR list entry.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing break statement so SHARED_KEY authentication doesn't
work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were no break statements in this switch statement so everything
used the default settings. Per Walter Harms's suggestion, I've replaced
the switch statement and done a little cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in ray_cs.c:
the a_current_ess_id is "Null terminated unless ESSID_SIZE long"
so we need buffer it with '\0' firstly, before using strlen or %s.
additional information:
in drivers/net/wireless/rayctl.h:
"NULL terminated unless 32 long" is a comment at line 616, 664
ESSID_SIZE is 32, at line 190
in include/uapi/linux/wireless.h:
IW_ESSID_MAX_SIZE is also 32
in drivers/net/wireless/ray_cs.c:
use strncpy for it, without '\0' terminated, at line 639
use memcpy for it, assume not '\0' terminated in line 1092..1097
buffer it with '\0' firstly, before using %s, in line 2576, 2598..2600
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing "!" as we are supposed to check "!card->adapter"
in PCIe suspend handler.
Cc: "3.2+" <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Sergey V. <sftp.mtuci@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chain swapping should only be enabled when the EEPROM chainmask is set to 5,
regardless of what the runtime chainmask is.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reports the following warning with x86_64-randconfig-x955:
warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
(RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))
This warning was introduced in commit a290593, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: kbuild test robot <fengguang.wu@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not correctly change interface type when switching from
IBSS mode to STA mode, that results in microcode errors.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=886946
Reported-by: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christoph Paasch found netxen could trigger a BUG in its dismantle
phase, in netxen_release_tx_buffer(), using full size TSO packets.
cmd_buf->frag_count includes the skb->data part, so the loop must
start at index 1 instead of 0, or else we can make an out
of bound access to cmd_buff->frag_array[MAX_SKB_FRAGS + 2]
Christoph provided the fixes in netxen_map_tx_skb() function.
In case of a dma mapping error, its better to clear the dma fields
so that we don't try to unmap them again in netxen_release_tx_buffer()
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last update to the Ethernet HowTo (over 10 years ago) listed this:
------------------------
SEEQ 8005
Status: Obsolete, Driver Name: seeq8005
There is little information about the card included in the driver,
and hence little information to be put here. If you have a question,
you are probably best trying to e-mail the driver author as listed
in the source.
It was marked obsolete as of the 2.4 series kernels.
------------------------
If it was obsolete over a decade ago, the situation can not have
improved with the passage of time, so let us act on that. Even with
today's improved search engines, I was unable to locate any real
meaningful information on the ISA implementation of this rare chip.
There are ARM and SGI variants of the driver in tree, but they do
not depend on the original x86 driver source or header file. We
leave those non-x86 drivers to be deleted by the arch maintainers
when they decide to expire those legacy platforms as a whole.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.
Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:
"...designed to work with all kernels > 1.1.33"
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them. Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is an area I know all too well, after being author of several 8390
drivers, and maintainer of all 8390 drivers during a large part of their
active lifecycle.
To that end, I can say this with a reasonable degree of confidence.
The drivers deleted here represent the earliest (as in early 1990)
hardware and/or rare hardware. The remaining hardware not deleted
here is the more modern/sane of the lot, with ISA-PnP and jumperless
"soft configuration" like the wd and smc cards had.
The original ne2000 driver (ne.c) gets a pass at this time since
AT/LANTIC based cards that could be both ne2000 or wd-like (with
shared memory) and with jumperless configuration were made in the
mid to late 1990's, and performed reasonably well for their era.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another driver for relatively rare 10Mbit hardware that
originated in the early 1990's. So we select it for removal at
this point in time as well.
Cc: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These Fujitsu MB86965 based ISA 10Mbit cards were another of the
relatively rare cards dating from the early 1990s that for one reason
or another didn't seem to get a lot of use in linux. So we retire it
now with a reasonable degree of confidence that it won't impact anyone.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These cards were only available in 8bit format, and in addition
they only had AUI and BNC(10-Base2) interfaces (i.e. no RJ-45).
In fact, they are so rare, that an internet search on these old
cards almost comes up empty, unless the "Micom interlan" name
is used.
This puts them in the equivalent domain as the 3c501, so there
should be no strong opposition to the driver removal, as nobody
is seriously using 3.9+ with 8 bit ISA hardware.
In doing so, the whole "ethernet/racal" category becomes empty,
so we clean up the Makefile/Kconfig and subdir appropriately.
Cc: Andreas Mohr <andi@lisas.de>
Cc: Jan-Pascal van Best <janpascal@vanbest.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Like the other drivers that were in the ISA i825xx family, the ni52
was rather rare, not widely used, and hence perhaps not as reliable
as the more mainstream ISA drivers that were heavily used. Given
that, it is chosen for retirement at this time as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver supported early to mid 1990's Zenith laptops, of the
2" thick variety. The driver was already dead 10+ years ago, but
we see this in the source:
----------------
/* 10/2002
[...]
Tested on a vintage Zenith Z-Note 433Lnp+. Probably broken on
anything else. Testers (and detailed bug reports) are welcome :-).
----------------
To clarify, a 433 translates into a 486 at 33MHz, and a system with
a default of 4MB RAM. I can't fault the noble effort to keep things
working a decade ago, but at this point in time, there is no valid
justification to continue carrying this driver along.
Note that there is no associated Space.c cleanup here since this
driver was using module_init to hook itself in.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These old drivers should not be confused with the very common PCI
cards that are supported by e100.c -- these older 10Mbit ISA only
drivers were not as commonly used as some of the other ISA drivers,
simply due to hardware availability and pricing.
Given the rarity of the hardware, and the subsequent less extensive
use of the drivers, it makes sense to obsolete them at this point
in time, along with other rare/experimental ISA drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For those of us who were around in the early to mid 1990's, we
will remember that the i825xx ethernet support was not something
that was considered sufficiently vetted for 24/7 use.
Folks might be inclined to use *functional* ISA hardware on some
near expired P3 ISA machines for dedicated workhorse applications,
but the odds of using (and relying on) one of these old/experimental
drivers is essentially nil. So lets remove them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parallel port is largely replaced by USB, and even in the
day where these drivers were current, the documented speed was
less than 100kB/s. Let us not pretend that anyone cares about
these drivers anymore, or worse - pretend that anyone is using
them on a modern kernel.
As a side bonus, this is the end of legacy parallel port ethernet,
so we get to drop the whole chunk relating to that in the legacy
Space.c file containing the non-PCI unified probe dispatch.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was amusing that linux was able to make use of this 1980's
technology on machines long past its intended lifespan, but
it probably should go now.
To set some context, the 3c501 was designed in the 1980's to be
used on 8088 PC-XT 8bit ISA machines. It was built using a large
number of discrete TTL components and truly looks like a relic
of the ancient past before large scale integration was common.
But from a functional point of view, the real issue, as stated
in the (also obsolete) Ethernet-HowTo, is that "...the 3c501 can
only do one thing at a time -- while you are removing one packet
from the single-packet buffer it cannot receive another packet,
nor can it receive a packet while loading a transmit packet."
You know things are not good when the Kconfig help text suggests
you make a cron job doing a ping every minute.
Hardware that old and crippled is simply not going to be used by
anyone in a time where 10 year old 100Mbit PCI cards (that are
still functional) are largely give-away items.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver was specific to a "professional workstation" line
of products from around 1993 that used the i82596 ethernet chip
as an on-board ethernet solution.
With a 486 processor, and the premium top of the line model maxing
out at a clock speed of 50MHz, we can safely retire this support.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Apricot was a 486 PC with 4MB RAM, and an on-board ethernet
via an intel i82596 hard-wired to i/o 0x300.
Those who were using linux in the 1990's will recall that the
i82596 driver was not one of the more stable or widely used
drivers of its day. Combine that with the extremely limited
resources of the platform, and it is truly time to expire the
support for this thing.
There are some old m68k targets who were also using this chip,
so rather than poll the m68k user base, we simply cut out the
x86/Apricot support here in this commit.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Delete successive tests to the same location. rc was previously tested and
not subsequently updated. efx_phc_adjtime can return an error code, so the
call is updated so that is tested instead.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Infineon(now Intel) HSPA Modem platform NCM cannot support ARP.
we can define a new common structure wwan_noarp_info.
Then more similiar NO ARP devices can be handled easily
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do have some USB net devices, which cannot do ARP.
so we can introduce a new flag FLAG_NOARP, then client drivers
can easily handle this kind of devices
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bbc8d92 (net: cdc_ncm: add Huawei devices) implemented
support for devices with a single combined control and data
interface. Fix up the error path so that we do not double
release such interfaces in case of probing failures.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
We normally avoid sending ZLPs by padding NTBs with a zero byte
if the NTB is shorter than dwNtbOutMaxSize, resulting in a short
USB packet instead of a ZLP. But in the case where the NTB length
is exactly dwNtbOutMaxSize and this is an exact multiplum of
wMaxPacketSize, then we must send a ZLP.
This fixes an issue seen on a Sierra Wireless MC7710 device
where the transmission would fail whenever we ended up padding
the NTBs to max size.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for the MBIM mode in some Sierra Wireless devices.
Some Sierra Wireless firmwares support CDC MBIM but have no CDC
Union funtional descriptor. This violates the MBIM specification,
but we can easily work around the bug by looking at the Interface
Association Descriptor instead. This is most likely what
Windows uses too, which explains how the firmware bug has gone
unnoticed until now.
This change will not affect any currently supported device
conforming to the NCM or MBIM specifications, as they must have
the CDC Union descriptor.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we write MAC address to pci config space byte by byte,
this means that we have an intermediate step where mac is wrong.
This patch introduced a new control command to set MAC address,
it's atomic.
VIRTIO_NET_F_CTRL_MAC_ADDR is a new feature bit for compatibility.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to send vq command to set mac address in
virtnet_set_mac_address(), so do this function moving.
Fixed a little issue of coding style.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the transmit DMA channel field in struct emac_priv
is txchan, not txch.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch calls device_set_wakeup_enable() inside set_wol
callback, so that turning on WOL from user mode utility
can make the 'wakeup' of pegasus device to be enabled, then
remote wakeup may be enabled before putting into sleep.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant code from build_inline_wqe()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed wrong mac length, it should be ETH_ALEN,
also replaced the hardcode 6 in hyperv_net.h
Signed-off-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates Copyright year to 2013
v2: Changed Copyright year on Makefile
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the physical function (PF) is reset for any reason the statistics
collection in ixgbevf_update_stats needs to wait to update until after
the reset synchronization ensures that the PF driver is up and running
and is finished with its own reset. Go ahead and clear the link flag to
indicate this when the control message from the PF is received. The
reset synchronization and recovery in the watchdog task will eventually
set the link flag up when the PF has resumed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dev_info to log link up/down messages.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts. The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map. To do this I have expanded the work done in the main loop by
pushing first into tx_buffer. This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor. The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo. By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.
To do this I also needed to change the logic and/or drop some flags. I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do. Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb. Instead we can just check the bitflag in the skb.
In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway. Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads. Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.
With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Johannes Berg