Add documentation to ieee80211_rx_ba_offl() function and, while at it,
rename the bit argument to tid, for consistency.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With TXQs, the AP_VLAN interfaces are resolved to their owner AP
interface when enqueuing the frame, which makes sense since the
frame really goes out on that as far as the driver is concerned.
However, this introduces a problem: frames to be encrypted with
a VLAN-specific GTK will now be encrypted with the AP GTK, since
the information about which virtual interface to use to select
the key is taken from the TXQ.
Fix this by preserving info->control.vif and using that in the
dequeue function. This now requires doing the driver-mapping
in the dequeue as well.
Since there's no way to filter the frames that are sitting on a
TXQ, drop all frames, which may affect other interfaces, when an
AP_VLAN is removed.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers handle rx buffer reordering internally (and by extension
handle also the rx ba session timer internally), but do not ofload the
addba/delba negotiation.
Add an api for these drivers to properly tear-down the ba session,
including sending a delba.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of using the SKB queue with the fake pkt_type for the
offloaded RX BA session management, also handle this with the
normal aggregation state machine worker. This also makes the
use of this more reliable since it gets rid of the allocation
of the fake skb.
Combined with the previous patch, this finally allows us to
get rid of the pkt_type hack entirely, so do that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
CoDel can be too aggressive if a station sends at a very low rate,
leading reduced throughput. This gets worse the more stations are
present, as each station gets more bursty the longer the round-robin
scheduling between stations takes.
This adds dynamic adjustment of CoDel parameters per station. It uses
the rate selection information to estimate throughput and sets more
lenient CoDel parameters if the estimated throughput is below a
threshold (modified by the number of active stations).
A new callback is added that drivers can use to notify mac80211 about
changes in expected throughput, so the same adjustment can be made for
cards that implement rate control in firmware. Drivers that don't use
this will just get the default parameters.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[remove currently unnecessary EXPORT_SYMBOL, fix kernel-doc, remove
inline annotation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow I missed this in my RX rate cleanup series, causing some
drivers to not report correct bandwidth since this flag isn't
used by mac80211 anymore. Fix this, and make hwsim also report
higher bandwidths appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows the driver to pass in struct ieee80211_tx_status directly.
Make ieee80211_tx_status_noskb a wrapper around it.
As with ieee80211_tx_status_noskb, there is no _ni variant of this call,
because it probably won't be needed.
Even if the driver won't provide any extra status info other than what's
in struct ieee80211_tx_info already, it can optimize status reporting
this way by passing in the station pointer.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[use C99 initializers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename .tx_status_noskb to .tx_status_ext and pass a new on-stack
struct ieee80211_tx_status instead of struct ieee80211_tx_info.
This struct can be used to pass extra information, e.g. for dynamic tx
power control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This field will need to be used again for HE, so rename it now.
Again, mostly done with this spatch:
@@
expression status;
@@
-status->vht_nss
+status->nss
@@
expression status;
@@
-status.vht_nss
+status.nss
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211. There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
an user||a user
an userspace||a userspace
I also added "userspace" to the list since it is a common word in Linux.
I found some instances for "an userfaultfd", but I did not add it to the
list. I felt it is endless to find words that start with "user" such as
"userland" etc., so must draw a line somewhere.
Link: http://lkml.kernel.org/r/1481573103-11329-4-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For a few restructured text warnings in mac80211, making the
documentation warning-free (for now).
In order to not add trailing whitespace, but also not introduce
too much noise into this change, move just the affected docs
into inline comments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flag that indicates that the WEP ICV was stripped from an
RX packet, allowing the device to not transfer that if it's
already checked.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The uapsd_queue field is in QoS IE order and not in
IEEE80211_AC_*'s order.
This means that mac80211 would get confused between
BK and BE which is certainly not such a big deal but
needs to be fixed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi will check internally that the tid maps to an AC
that is trigger enabled, but can't know what tid exactly.
Allow the driver to pass a generic tid and make mac80211
assume that a trigger frame was received.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
According to IEEE 802.11-2012 section 8.3.2 table 8-19, the outer SA/DA
of A-MSDU frames need to be changed depending on FromDS/ToDS values.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use ether_addr_copy and add alignment annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TXQ intermediate queues can cause packet reordering when more than
one flow is active to a single station. Since some of the wifi-specific
packet handling (notably sequence number and encryption handling) is
sensitive to re-ordering, things break if they are applied before the
TXQ.
This splits up the TX handlers and fast_xmit logic into two parts: An
early part and a late part. The former is applied before TXQ enqueue,
and the latter after dequeue. The non-TXQ path just applies both parts
at once.
Because fragments shouldn't be split up or reordered, the fragmentation
handler is run after dequeue. Any fragments are then kept in the TXQ and
on subsequent dequeues they take precedence over dequeueing from the FQ
structure.
This approach avoids having to scatter special cases all over the place
for when TXQ is enabled, at the cost of making the fast_xmit and TX
handler code slightly more complex.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[fix a few code-style nits, make ieee80211_xmit_fast_finish void,
remove a useless txq->sta check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows the mesh sync (and debugfs) code to make incremental
TSF adjustments, avoiding any uncertainty introduced by delay in
programming absolute TSF.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide an API to report NAN function match. Mac80211 will lookup the
corresponding cookie and report the match to cfg80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement nan_change_conf callback which allows to change current
NAN configuration (master preference and dual band operation).
Store the current NAN configuration in sdata, so it can be used
both to provide the driver the updated configuration with changes
and also it will be used in hw reconfig flows in next patches.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on consecutive msdu failures, mac80211 triggers CQM packet-loss
mechanism. Drivers like ath10k that have its own connection monitoring
algorithm, offloaded to firmware for triggering station kickout. In case
of station kickout, driver will report low ack status by mac80211 API
(ieee80211_report_low_ack).
This flag will enable the driver to completely rely on firmware events
for station kickout and bypass mac80211 packet loss mechanism.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No drivers implement this, relying either on the recursive
directory removal to remove their debugfs, or not having any
to start with. Remove the dead driver callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the existing device timestamp from the RX status information
to add support for the new radiotap timestamp field. Currently
only 32-bit counters are supported, but we also add the radiotap
mactime where applicable. This new field allows more flexibility
in where the timestamp is taken etc. The non-timestamp data in
the field is taken from a new field in the hw struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ability to change the max_rx_aggregation frames is useful
in cases of IOP.
There exist some devices (latest mobile phones and some AP's)
that tend to not respect a BA sessions maximum size (in Kbps).
These devices won't respect the AMPDU size that was negotiated during
association (even though they do respect the maximal number of packets).
This violation is characterized by a valid number of packets in
a single AMPDU. Even so, the total size will exceed the size negotiated
during association.
Eventually, this will cause some undefined behavior, which in turn
causes the hw to drop packets, causing the throughput to plummet.
This patch will make the subframe limitation to be held by each station,
instead of being held only by hw.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.
This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no other limit other than a global
packet count limit when using software queuing.
This means a single flow queue can grow insanely
long. This is particularly bad for TCP congestion
algorithms which requires a little more
sophisticated frame dropping scheme than a mere
headdrop on limit overflow.
Hence apply (a slighly modified, to fit the knobs)
CoDel5 on flow queues. This improves TCP
convergence and stability when combined with
wireless driver which keeps its own tx queue/fifo
at a minimum fill level for given link conditions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Qdiscs are designed with no regard to 802.11
aggregation requirements and hand out
packet-by-packet with no guarantee they are
destined to the same tid. This does more bad than
good no matter how fairly a given qdisc may behave
on an ethernet interface.
Software queuing used per-AC netdev subqueue
congestion control whenever a global AC limit was
hit. This meant in practice a single station or
tid queue could starve others rather easily. This
could resonate with qdiscs in a bad way or could
just end up with poor aggregation performance.
Increasing the AC limit would increase induced
latency which is also bad.
Disabling qdiscs by default and performing
taildrop instead of netdev subqueue congestion
control on the other hand makes it possible for
tid queues to fill up "in the meantime" while
preventing stations starving each other.
This increases aggregation opportunities and
should allow software queuing based drivers
achieve better performance by utilizing airtime
more efficiently with big aggregates.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Requires software tx queueing and fast-xmit support. For good
performance, drivers need frag_list support as well. This avoids the
need for copying data of aggregated frames. Running without it is only
supported for debugging purposes.
To avoid performance and packet size issues, the rate control module or
driver needs to limit the maximum A-MSDU size by setting
max_rc_amsdu_len in struct ieee80211_sta.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix locking issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver advertises the new HW flag USE_RSS, make the
station statistics on the fast-rx path per-CPU. This will
enable calling the RX in parallel, only hitting locking or
shared cachelines when the fast-RX path isn't available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes drivers already looked up, or know out-of-band
from their device, which station transmitted a given RX
frame. Allow them to pass the station pointer to mac80211
to save the extra lookup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO
has a legacy client connected to it, it should disable P2P PS mechanisms.
Let the driver know about this with a new bss_conf parameter.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add documentation for the flag for duplication check.
Fixes the following warning when running make htmldocs:
warning: Enum value 'RX_FLAG_DUP_VALIDATED' not described in enum 'mac80211_rx_flags'
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
[fix description]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Luca Coelho