H3 has two SPI controllers. The size of the buffer is 64 * 8.
(8 bit transfer by 64 entry FIFO)
A31 has four controllers. The size of the buffer is 128 * 8.
(8 bit transfer by 128 entry FIFO)
Register maps are sharable, so sun6i SPI driver is reusable with
device configuration.
Use the variable, 'fifo_depth' instead of fixed value to support both SPI
controllers.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The speed limits are unset in the sun4i and sun6i SPI drivers.
The maximum speed of SPI master is used when maximum speed of SPI slave
is not specified. Also the __spi_validate function should check that
transfer speeds do not exceed the master limits.
The user manual for A10 and A31 specifies maximum
speed of the SPI clock as 100MHz and minimum as 3kHz.
Setting the SPI clock to out-of-spec values can lock up the SoC.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
--
v2:
new patch
v3:
fix constant style
Signed-off-by: Mark Brown <broonie@kernel.org>
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The sun4i spi hardware can trasfer at most 63 bytes of data without DMA
support so report the limitation. Same for sun6i.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow transfers to set the transmission speed rather than using the
device max_speed_hz value. The SPI core makes sure that the speed_hz
value is always set on the transfer.
Signed-off-by: Marcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This controller only supports 8 bits word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code in sun6i_spi_set_cs() actually clears CPHA and CPOL bits which is
obvious wrong. The define for SUN6I_TFR_CTL_CS_MASK is wrong. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Allwinner A31 has a new SPI controller IP compared to the older Allwinner
SoCs.
It supports DMA, but the driver only does PIO for now, and DMA will be
supported eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Milo Kim