It seems very unlikely that eMMC devices would hold a standard
partitiontable in one of it's boot areas. Therefore, let's prevent
them from being scanned.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.
There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.
In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently when the device secure discard implementation is
blacklisted (MMC_QUIRK_SEC_ERASE_TRIM_BROKEN quirk is set)
instead of secure discard we're going to do normal discard,
which is wrong.
When the secure discard is known to be broken we should just
disallow it entirely and not advertise this functionality to
the user. Fix it.
Also move mmc_fixup_device() in from of mmc_blk_alloc() so we
can get quirks set before we attempt to set queue information.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
When sending a stop command at the recovery path, use a R1B response
when the failing data request are a WRITE. Thus we also care about the
busy detection completion in this case.
For a failing READ request, we use a R1 response for the stop command,
since we don't need to care about busy detection in this case.
To align behavior between hosts supporting MMC_CAP_WAIT_WHILE_BUSY and
those who are not, we add a CMD13 polling method for the card's status.
We also respect whether the host has specified the max_busy_timeout,
which means we may fallback to CMD13 polling if the timeout is greater
than what the host are able to support.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Currently for write request we don't trust the hw busy detection to be
fully handled by host, thus we also poll the card's status until we see
it's gets out of the busy state.
Still there are scenarios where it will a benefit to trust the hw busy
detection done by the host, since no additional polling is needed.
Let's prepare card_busy_detect() to be able to handle this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
To complete a data write request we poll for the card's status register
by sending CMD13. The are other scenarios when this polling method are
needed, which is why we here moves this code to it's own function. No
functional change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
While using open ended transmission and thus ending the transfer by
sending a stop command, we shall use R1B only for writes and R1 shall
be used for reads. Previously R1B were used in both cases.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We must use a 64-bit for this, otherwise overflowed bits get lost, and
that can result in a lower than intended value set.
Fixes: 8e0cb8a1f6 ("ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Fixes: 7d35496dd9 ("ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations")
Tested-Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no need for keeping a host cap for MMC_CAP2_SANITIZE, instead
we just make the feature default available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Under function mmc_blk_issue_rq, after an MMC discard operation,
the MMC request data structure may be freed in memory. Later in
the same function, the check of req->cmd_flags & MMC_REQ_SPECIAL_MASK
is dangerous and invalid. It causes the MMC host not to be released
when it should.
This patch fixes the issue by marking the special request down before
the discard/flush operation.
Reported by: Harold (SoonYeal) Yang <haroldsy@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
DMA bounce limit is the maximum direct DMA'able memory beyond which
bounce buffers has to be used to perform dma operations. MMC queue layr
relies on dma_mask but its calculation is based on max_*pfn which
don't have uniform meaning across architectures. So make use of
dma_max_pfn() which is expected to return the DMAable maximum pfn
value across architectures.
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By adding a card state that records if it is suspended or resumed, we
can accept asyncronus suspend/resume requests for the mmc and sd
bus_ops.
MMC_CAP_AGGRESSIVE_PM, will at request inactivity through the runtime
bus_ops callbacks, execute a suspend of the the card. In the state were
this has been done, we can receive a suspend request for the mmc bus,
which for sd and mmc forced the card to active state by a
pm_runtime_get_sync. In other words, the card was resumed and then
immediately suspended again, completely unnecessary.
Since the suspend/resume bus_ops callbacks for sd and mmc are now
capable of handling asynchronous requests, we no longer need to force
the card to active state before executing suspend. Evidently preventing
the above sequence for MMC_CAP_AGGRESSIVE_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
A previous commit (fdfa20c163) reordered the shutdown sequence
in mmc_blk_remove_req. However, mmc_cleanup_queue is now called before
we get the card pointer, and mmc_cleanup_queue sets mq->card to NULL.
This patch moves the card pointer assignment before mmc_cleanup_queue.
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be used.
Also, both kstrtol() and copy_from_user() can be replaced
with kstrtol_from_user() to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current MMC driver doesn't handle generic error (bit19 of device
status) in write sequence. As a result, write data gets lost when
generic error occurs. For example, a generic error when updating a
filesystem management information causes a loss of write data and
corrupts the filesystem. In the worst case, the system will never
boot.
This patch includes the following functionality:
1. To enable error checking for the response of CMD12 and CMD13
in write command sequence
2. To retry write sequence when a generic error occurs
Messages are added for v2 to show what occurs.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Signed-off-by: Chris Ball <cjb@laptop.org>
Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Inside the routine mmc_blk_ioctl_cmd() the sanitize command is
identified according to the value of bits 16-23 of the argument.
but what happens if a different command is sent, and only by
chance, bits 16-23 contain the value of SANITIZE command ?
In that case a SANITIZE command will be falsely identified.
In order to prevent such a case, the condition is expanded and
now it also checks the opcode itself, and verifies that it is an
MMC_SWITCH opcode.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We had a multi-partition SD-Card with two ext2 file systems. The partition
table was getting overwritten by a race between the card removal and
the unmount of the 2nd ext2 partition.
What was observed:
1. Suspend/resume would call to remove the device. The clearing
of the device information is done asynchronously.
2. A request is made to unmount the file system (this is called
after the removal has started).
3. The remapping table was cleared by the asynchronous part of
the device removal.
4. A write request to the super block (block 0 of the partition)
was sent down and instead of being remapped to the partition
offset, it was remapped to block 0 of the device which is where
the partition table is located.
5. Write was queued and written resulting in the overwriting
of the partition table with the ext2 super block.
6. The mmc_queue is cleaned up.
The mmc card device driver used to access SD cards, was calling del_gendisk
before calling mmc_cleanup-queue. The comment in the mmc_blk_remove_req
code indicated that it expected del_gendisk to block all further requests
from being queued but it doesn't. The mmc driver uses the presences of the
mmc_queue to determine if the request should be queued.
The fix was to clean up the mmc_queue before the rest of the
the delete partition code is called.
This prevents the overwriting of the partition table.
However, the umount gets an error trying to write the super block.
The umount should be issued before the device is removed but that
is not always possible. The umount is still needed to cleanup other
data structures.
Addresses the problem described in http://crbug.com/240815
Signed-off-by: Paul Taysom <taysom@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping mmc_power_up()
at boot/initialization time if it's already happened, for performance
(faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being put
into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed slowly;
we were missing card removal events if the card retained contact with
the slot pads for long enough to reply to a CMD13 while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use mmc_of_parse().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Pr7P
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.10:
Core:
- Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
mmc_power_up() at boot/initialization time if it's already
happened, for performance (faster boot time) reasons.
- Fix a bit width test failure that resulted in old eMMC cards being
put into 1-bit mode when 4-bit mode was available.
- Expose fwrev/hwrev for MMCv4 parts.
- Improve card removal logic in the case where the card's removed
slowly; we were missing card removal events if the card retained
contact with the slot pads for long enough to reply to a CMD13
while being removed.
Drivers:
- davinci_mmc: Support using PIO instead of DMA.
- dw_mmc: Add support for Exynos4412.
- mxcmmc: DT support, use slot-gpio API.
- mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
support.
- sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
- sdhci-tegra: Add support for Tegra114 platforms, use
mmc_of_parse()"
* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
mmc: core: fix init controller performance regression, updated patch
mmc: mxcmmc: enable DMA support on mpc512x
mmc: mxcmmc: constify mxcmci_devtype
mmc: mxcmmc: use slot-gpio API for write-protect detection
mmc: mxcmmc: add mpc512x SDHC support
mmc: mxcmmc: fix race conditions for host->req and host->data access
mmc: mxcmmc: DT support
mmc: dw_mmc: let device core setup the default pin configuration
mmc: mxs-mmc: add broken-cd property
mmc: mxs-mmc: add non-removable property
mmc: mxs-mmc: add cd-inverted property
mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
mmc: mxcmmc: Fix bug when card is present during boot
mmc: core: fix performance regression initializing MMC host controllers
Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
mmc: atmel-mci: pio hang on block errors
mmc: core: Fix bit width test failing on old eMMC cards
mmc: dw_mmc: Use pr_info instead of printk
mmc: dw_mmc: Check return value of regulator_enable
...
For normal request mmc_blk_issue_rq is called twice with asynchronous
transfer(cur and prev). Host's claim and release can be done in each
mmc_blk_issue_rq. However, Special request is currently excluded in
asynchronous transfer. After special request is finished, if there is
no new request, mmc_release_host won't be called in mmc_blk_issue_rq.
The problem is founded during mmc_suspend.
[<c0541124>] (__schedule+0x0/0x78c) from [<c05419e8>] (schedule+0x38/0x78)
[<c05419b0>] (schedule+0x0/0x78) from [<c03a843c>] (__mmc_claim_host+0xac/0x1b4)
[<c03a8390>] (__mmc_claim_host+0x0/0x1b4) from [<c03ac98c>] (mmc_suspend+0x28/0x9c)
[<c03ac964>] (mmc_suspend+0x0/0x9c) from [<c03aad24>] (mmc_suspend_host+0xb4/0x194)
...
Reported-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=dYdW
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's not necessary to start a new request while error handling if
the card was removed.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Unlike normal r/w request, special requests(discard, flush)
is finished with a one-time issue_fn. Request change to
mqrq_prev makes unnecessary call.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from Jiri and
bugfixes from Alan, along with a number of other tty and serial driver updates
by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the TTY
layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhgwACgkQMUfUDdst+ynI6wCcC+YeBwncnoWHvwLAJOwAZpUL
bysAn28o780/lOsTzp3P1Qcjvo69nldo
=hN/g
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial merge from Greg Kroah-Hartman:
"Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from
Jiri and bugfixes from Alan, along with a number of other tty and
serial driver updates by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the
TTY layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up some trivial conflicts in the staging tree, due to the fwserial
driver having come in both ways (but fixed up a bit in the serial tree),
and the ioctl handling in the dgrp driver having been done slightly
differently (staging tree got that one right, and removed both
TIOCGSOFTCAR and TIOCSSOFTCAR).
* tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (146 commits)
staging: sb105x: fix potential NULL pointer dereference in mp_chars_in_buffer()
staging/fwserial: Remove superfluous free
staging/fwserial: Use WARN_ONCE when port table is corrupted
staging/fwserial: Destruct embedded tty_port on teardown
staging/fwserial: Fix build breakage when !CONFIG_BUG
staging: fwserial: Add TTY-over-Firewire serial driver
drivers/tty/serial/serial_core.c: clean up HIGH_BITS_OFFSET usage
staging: dgrp: dgrp_tty.c: Audit the return values of get/put_user()
staging: dgrp: dgrp_tty.c: Remove the TIOCSSOFTCAR ioctl handler from dgrp driver
serial: ifx6x60: Add modem power off function in the platform reboot process
serial: mxs-auart: unmap the scatter list before we copy the data
serial: mxs-auart: disable the Receive Timeout Interrupt when DMA is enabled
serial: max310x: Setup missing "can_sleep" field for GPIO
tty/serial: fix ifx6x60.c declaration warning
serial: samsung: add devicetree properties for non-Exynos SoCs
serial: samsung: fix potential soft lockup during uart write
tty: vt: Remove redundant null check before kfree.
tty/8250 Add check for pci_ioremap_bar failure
tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
tty/8250 Add XR17D15x devices to the exar_handle_irq override
...
RPMB partition is accessing though /dev/block/mmcXrpmb device
User callers can read and write entire data frame(s) as defined
by JEDEC Standard JESD84-A441, using standard IOCTL interface.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not scan rpmb partitions for "soft" partitions, since the rpmb
partition contains protected data. Silences the following message
during boot:
mmcblkXRPMB: unknown partition table
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case both 'req' and 'mq->mqrq_prev->req' are null, there is no request
to be processed. That means there is no need to switch buffer.
Switching buffer is required only after finishing 'issue_fn'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
Here it is enough to switch to refcounting in tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty from struct sdio_uart_port is unused. Proper refcounted tty in
tty_port->tty is used instead. So remove the member from that
structure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
References:
http://forum.xda-developers.com/showthread.php?t=1644364https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkB
Signed-off-by: Ian Chen <ian.cy.chen@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@vger.kernel.org> [3.0+]
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently we have no way to assign tty->port while performing tty
installation. There are two ways to provide the link tty_struct =>
tty_port. Either by calling tty_port_install from tty->ops->install or
tty_port_register_device called instead of tty_register_device when
the device is being set up after connected.
In this patch we modify most of the drivers to do the latter. When the
drivers use tty_register_device and we have tty_port already, we
switch to tty_port_register_device. So we have the tty_struct =>
tty_port link for free for those.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For completing any block request, MMC block driver is calling:
spin_lock_irq(queue)
__blk_end_request()
spin_unlock_irq(queue)
But if we analyze the sources of latency in kernel using ftrace,
__blk_end_request() function at times may take up to 6.5ms with
spinlock held and irq disabled.
__blk_end_request() calls couple of functions and ftrace output
shows that blk_update_bidi_request() function is almost taking 6ms.
There are 2 function to end the current request: ___blk_end_request()
and blk_end_request(). Both these functions do same thing except
that blk_end_request() function doesn't take up the spinlock
while calling the blk_update_bidi_request().
This patch replaces all __blk_end_request() calls with
blk_end_request() and __blk_end_request_all() calls with
blk_end_request_all().
Testing done: 20 process concurrent read/write on sd card
and eMMC. Ran this test for almost a day on multicore system
and no errors observed.
This change is not meant for improving MMC throughput; it's basically
about becoming fair to other threads/interrupts in the system. By
holding spin lock and interrupts disabled for longer duration, we
won't allow other threads/interrupts to run at all. Actually slight
performance degradation at file system level can be expected as we
are not holding the spin lock during blk_update_bidi_request() which
means our mmcqd thread may get preempted for other high priority
thread or any interrupt in the system.
These are performance numbers (100MB file write) with eMMC running
in DDR mode:
Without this patch:
Name of the Test Value Unit
LMDD Read Test 53.79 MBPS
LMDD Write Test 18.86 MBPS
IOZONE Read Test 51.65 MBPS
IOZONE Write Test 24.36 MBPS
With this patch:
Name of the Test Value Unit
LMDD Read Test 52.94 MBPS
LMDD Write Test 16.70 MBPS
IOZONE Read Test 52.08 MBPS
IOZONE Write Test 23.29 MBPS
Read numbers are fine. Write numbers are bit down (especially LMDD
write), may be because write requests normally have large transfer
size and which means there are chances that while mmcq is executing
blk_update_bidi_request(), it may get interrupted by interrupts or
other high priority thread.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If multi block write operation fails for SD card, during
error handling we send the SD_APP_SEND_NUM_WR_BLKS (ACMD22)
to know how many blocks were already programmed by card.
But mmc_sd_num_wr_blocks() function which sends the ACMD22
calculates the data timeout value from csd.tacc_ns and
csd.tacc_clks parameters which will be 0 for block addressed
(>2GB cards) SD card. This would result in timeout_ns and
timeout_clks being 0 in the mmc_request passed to host driver.
This means host controller would program its data timeout timer
value with 0 which could result in DATA TIMEOUT errors from
controller.
To fix this issue, mmc_sd_num_wr_blocks() should instead
just call the mmc_set_data_timeout() to calculate the
data timeout value. mmc_set_data_timeout() function
ensures that non zero timeout value is set even for
block addressed SD cards.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for large sector size of 4KB by disabling
emulation. This patch passes eMMC DATA_SECTOR_SIZE as the logical
block size during mmc_blk_alloc_req.
In order to use this patch for 4KB sector size, ensure that
USE_NATIVE_SECTOR is enabled, partition table is 4KB sector size
aligned and file system block and sector size are 4KB multiples.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
After the null check on md the code jumped to cmd_done, which then
will dereference md in mmc_blk_put. This patch avoids the possible
null pointer dereference in that case.
Signed-off-by: Philippe De Swert <philippedeswert@gmail.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not needed to memset, as they are pointers and are assigned
to proper values in the next line anyway.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The name mmc_request is used for both the issue function
and a data structure, which creates conflicts in symbol lookups
in editors. Rename the function to mmc_request_fn.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.
Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC v4.5 sanitize operation erases all copies of unmapped
data. However trim or erase operations must be used first
to unmap the required sectors. That was not being done.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC v4.5 discard operation is significantly different from the
existing trim operation because it is not guaranteed to work with
the new sanitize operation. Consequently mmc_can_trim() is
separated from mmc_can_discard().
Also the new discard operation does not result in the sectors being
set to all-zeros, so discard_zeroes_data must not be set.
In addition, the new discard has the same timeout as trim, but from
v4.5 trim is defined to use the hc timeout. The timeout calculation
is adjusted accordingly.
Fixes apply to linux 3.2 on.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Subhash Jadavani <subhashj@codeauora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=T4T+
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty layer,
and a number of patches from Alan to help try to wrestle the vt layer
into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9nihQACgkQMUfUDdst+ylXTQCdFuwVuZgjCts+xDVa1jX2ac84
UogAn3Wr+P7NYFN6gvaGm52KbGbZs405
=2b/l
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
All num, magic and owner are set by alloc_tty_driver. No need to
re-set them on each allocation site.
pti driver sets something different to what it passes to
alloc_tty_driver. It is not a bug, since we don't use the lines
parameter in any way. Anyway this is fixed, and now we do the right
thing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the helper in the rest of the tty drivers. This is a simple
replacement.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LJnN
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC highlights for 3.3:
Core:
* Support for the HS200 high-speed eMMC mode.
* Support SDIO 3.0 Ultra High Speed cards.
* Kill pending block requests immediately if card is removed.
* Enable the eMMC feature for locking boot partitions read-only
until next power on, exposed via sysfs.
Drivers:
* Runtime PM support for Intel Medfield SDIO.
* Suspend/resume support for sdhci-spear.
* sh-mmcif now processes requests asynchronously.
* tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits)
mmc: fix a deadlock between system suspend and MMC block IO
mmc: sdhci: restore the enabled dma when do reset all
mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation
mmc: host: Adds support for eMMC 4.5 HS200 mode
mmc: core: HS200 mode support for eMMC 4.5
mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT()
mmc: core: Separate the timeout value for cache-ctrl
mmc: sdhci-spear: Fix compilation error
mmc: sdhci: Deal with failure case in sdhci_suspend_host
mmc: dw_mmc: Clear the DDR mode for non-DDR
mmc: sd: Fix SDR12 timing regression
mmc: sdhci: Fix tuning timer incorrect setting when suspending host
mmc: core: Add option to prevent eMMC sleep command
mmc: omap_hsmmc: use threaded irq handler for card-detect.
mmc: sdhci-pci: enable runtime PM for Medfield SDIO
mmc: sdhci: Always pass clock request value zero to set_clock host op
mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
mmc: sdhci-pci: get gpio numbers from platform data
mmc: sdhci-pci: add platform data
mmc: sdhci: prevent card detection activity for non-removable cards
...
Kill block requests when the host realizes that the card is
removed from the slot and is sure that subsequent requests
are bound to fail. Do this silently so that the block
layer doesn't output unnecessary error messages.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:
/sys/block/mmcblkXbootY/ro_lock_until_next_power_on
Each boot partition is locked by writing 1 to its file.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the read or write buffer size associated with the command sent
through the mmc_blk_ioctl is zero, do not prepare data buffer.
This enables a ioctl(2) call to for instance send a MMC_SWITCH to set
a byte in the ext_csd.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If max_seg_size is unaligned, mmc_test_map_sg() may create sg element
sizes that are not aligned with 512 byte. Fix, align max_seg_size at
mmc_test_area_init().
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
No functional change; adds macros for card manufacturer IDs.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Andrei E. Warkentin <andrey.warkentin@gmail.com>
Cc: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.
This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors. Since there is no access, mmcboot0/1
devices should not be created. Add a host capability to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error. However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC core provides a checking function that checks if the reset
has happended. Add a test to use that function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning "drivers/mmc/card/queue.c:111:20: warning:
symbol 'mmc_alloc_sg' was not declared. Should it be static?"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new REQ_PRIO to let requests preempt others in the cfq I/O schedule,
and lave REQ_META purely for marking requests as metadata in blktrace.
All existing callers of REQ_META except for XFS are updated to also
set REQ_PRIO for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We already check for ongoing async transfers when handling discard
requests, but not in mmc_blk_issue_flush(). This patch fixes that
omission.
Tested with an SDHCI controller and eMMC4.41.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change mmc_blk_issue_rw_rq() to become asynchronous.
The execution flow looks like this:
* The mmc-queue calls issue_rw_rq(), which sends the request
to the host and returns back to the mmc-queue.
* The mmc-queue calls issue_rw_rq() again with a new request.
* This new request is prepared in issue_rw_rq(), then it waits for
the active request to complete before pushing it to the host.
* When the mmc-queue is empty it will call issue_rw_rq() with a NULL
req to finish off the active request without starting a new request.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an additional mmc queue request instance to make way for two active
block requests. One request may be active while the other request is
being prepared.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Break out code without functional changes. This simplifies the code and
makes way for handling two parallel requests.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Break out code from mmc_blk_issue_rw_rq to create a block request prepare
function. This doesn't change any functionallity. This helps when handling
more than one active block request.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The way the request data is organized in the mmc queue struct, it only
allows processing of one request at a time. This patch adds a new struct
to hold mmc queue request data such as sg list, request, blk request and
bounce buffers, and updates any functions depending on the mmc queue
struct. This prepares for using multiple active requests in one mmc queue.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a test that measures how the mmc bandwidth depends on the numbers of
sg elements in the sg list. The transfer size if fixed and sg length goes
from a few up to 512. The purpose is to measure overhead caused by
multiple sg elements.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add four tests for read and write performance per
different transfer size, 4k to 4M.
* Read using blocking mmc request
* Read using non-blocking mmc request
* Write using blocking mmc request
* Write using non-blocking mmc request
The host driver must support pre_req() and post_req()
in order to run the non-blocking test cases.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debugfs file "testlist" to print all available tests.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some host controllers will not operate without a hardware
timeout that is limited in value. However large discards
require large timeouts, so there needs to be a way to
specify the maximum discard size.
A host controller driver may now specify the maximum discard
timeout possible so that max_discard_sectors can be calculated.
However, for eMMC when the High Capacity Erase Group Size
is not in use, the timeout calculation depends on clock
rate which may change. For that case Preferred Erase Size
is used instead.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ulf Hansson