My implementation around IFF_NO_QUEUE driver flag assumed that leaving
tx_queue_len untouched (specifically: not setting it to zero) by drivers
would make it possible to assign a regular qdisc to them without having
to worry about setting tx_queue_len to a useful value. This was only
partially true: I overlooked that some drivers don't call ether_setup()
and therefore not initialize tx_queue_len to the default value of 1000.
Consequently, removing the workarounds in place for that case in qdisc
implementations which cared about it (namely, pfifo, bfifo, gred, htb,
plug and sfb) leads to problems with these specific interface types and
qdiscs.
Luckily, there's already a sanitization point for drivers setting
tx_queue_len to zero, which can be reused to assign the fallback value
most qdisc implementations used, which is 1.
Fixes: 348e3435cb ("net: sched: drop all special handling of tx_queue_len == 0")
Tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the unaligned accesses seen on GRE TEB tunnels when
generating hash keys. Specifically what this patch does is make it so that
we force the use of skb_copy_bits when the GRE inner headers will be
unaligned due to NET_IP_ALIGNED being a non-zero value.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue with unaligned accesses when using
eth_get_headlen on a page that was DMA aligned instead of being IP aligned.
The fact is when trying to check the length we don't need to be looking at
the flow label so we can reorder the checks to first check if we are
supposed to gather the flow label and then make the call to actually get
it.
v2: Updated path so that either STOP_AT_FLOW_LABEL or KEY_FLOW_LABEL can
cause us to check for the flow label.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad40 ("unix: properly account for FDs passed over unix sockets")
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO is currently not aware of tunnel metadata generated by lightweight
tunnels and stored in the dst. This leads to two possible problems:
* Incorrectly merging two frames that have different metadata.
* Leaking of allocated metadata from merged frames.
This avoids those problems by comparing the tunnel information before
merging, similar to how we handle other metadata (such as vlan tags),
and releasing any state when we are done.
Reported-by: John <john.phillips5@hpe.com>
Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Dionne discovered a NULL pointer dereference when setting
SO_REUSEPORT on a socket after it is bound.
This patch removes the assumption that at least one socket in the
reuseport group is bound with the SO_REUSEPORT option before other
bind calls occur.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A quick set of bug fixes after there initial networking merge:
1) Netlink multicast group storage allocator only was tested with
nr_groups equal to 1, make it work for other values too. From
Matti Vaittinen.
2) Check build_skb() return value in macb and hip04_eth drivers, from
Weidong Wang.
3) Don't leak x25_asy on x25_asy_open() failure.
4) More DMA map/unmap fixes in 3c59x from Neil Horman.
5) Don't clobber IP skb control block during GSO segmentation, from
Konstantin Khlebnikov.
6) ECN helpers for ipv6 don't fixup the checksum, from Eric Dumazet.
7) Fix SKB segment utilization estimation in xen-netback, from David
Vrabel.
8) Fix lockdep splat in bridge addrlist handling, from Nikolay
Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
bgmac: Fix reversed test of build_skb() return value.
bridge: fix lockdep addr_list_lock false positive splat
net: smsc: Add support h8300
xen-netback: free queues after freeing the net device
xen-netback: delete NAPI instance when queue fails to initialize
xen-netback: use skb to determine number of required guest Rx requests
net: sctp: Move sequence start handling into sctp_transport_get_idx()
ipv6: update skb->csum when CE mark is propagated
net: phy: turn carrier off on phy attach
net: macb: clear interrupts when disabling them
sctp: support to lookup with ep+paddr in transport rhashtable
net: hns: fixes no syscon error when init mdio
dts: hisi: fixes no syscon fault when init mdio
net: preserve IP control block during GSO segmentation
fsl/fman: Delete one function call "put_device" in dtsec_config()
hip04_eth: fix missing error handle for build_skb failed
3c59x: fix another page map/single unmap imbalance
3c59x: balance page maps and unmaps
x25_asy: Free x25_asy on x25_asy_open() failure.
mlxsw: fix SWITCHDEV_OBJ_ID_PORT_MDB
...
Skb_gso_segment() uses skb control block during segmentation.
This patch adds 32-bytes room for previous control block which
will be copied into all resulting segments.
This patch fixes kernel crash during fragmenting forwarded packets.
Fragmentation requires valid IP CB in skb for clearing ip options.
Also patch removes custom save/restore in ovs code, now it's redundant.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Link: http://lkml.kernel.org/r/CALYGNiP-0MZ-FExV2HutTvE9U-QQtkKSoE--KN=JQE5STYsjAA@mail.gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
The unified hierarchy memory controller is going to use this jump label
as well to control the networking callbacks. Move it to the memory
controller code and give it a more generic name.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There won't be any separate counters for socket memory consumed by
protocols other than TCP in the future. Remove the indirection and link
sockets directly to their owning memory cgroup.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There won't be a tcp control soft limit, so integrating the memcg code
into the global skmem limiting scheme complicates things unnecessarily.
Replace this with simple and clear charge and uncharge calls--hidden
behind a jump label--to account skb memory.
Note that this is not purely aesthetic: as a result of shoehorning the
per-memcg code into the same memory accounting functions that handle the
global level, the old code would compare the per-memcg consumption
against the smaller of the per-memcg limit and the global limit. This
allowed the total consumption of multiple sockets to exceed the global
limit, as long as the individual sockets stayed within bounds. After
this change, the code will always compare the per-memcg consumption to
the per-memcg limit, and the global consumption to the global limit, and
thus close this loophole.
Without a soft limit, the per-memcg memory pressure state in sockets is
generally questionable. However, we did it until now, so we continue to
enter it when the hard limit is hit, and packets are dropped, to let
other sockets in the cgroup know that they shouldn't grow their transmit
windows, either. However, keep it simple in the new callback model and
leave memory pressure lazily when the next packet is accepted (as
opposed to doing it synchroneously when packets are processed). When
packets are dropped, network performance will already be in the toilet,
so that should be a reasonable trade-off.
As described above, consumption is now checked on the per-memcg level
and the global level separately. Likewise, memory pressure states are
maintained on both the per-memcg level and the global level, and a
socket is considered under pressure when either level asserts as much.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the jump-label from sock_update_memcg() and sock_release_memcg() to
the callsite, and so eliminate those function calls when socket
accounting is not enabled.
This also eliminates the need for dummy functions because the calls will
be optimized away if the Kconfig options are not enabled.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ARM64, a BUG() is triggered in the eBPF JIT if a filter with a
constant shift that can't be encoded in the immediate field of the
UBFM/SBFM instructions is passed to the JIT. Since these shifts
amounts, which are negative or >= regsize, are invalid, reject them in
the eBPF verifier and the classic BPF filter checker, for all
architectures.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible null pointer dereference that may occur when calling
skb_reserve() on a null skb.
Fixes: 879c7220e8 ("net: pktgen: Observe needed_headroom of the device")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After IPv6 support has recently been added to metadata dst and related
encaps, add support for populating/reading it from an eBPF program.
Commit d3aa45ce6b ("bpf: add helpers to access tunnel metadata") started
with initial IPv4-only support back then (due to IPv6 metadata support
not being available yet).
To stay compatible with older programs, we need to test for the passed
structure size. Also TOS and TTL support from the ip_tunnel_info key has
been added. Tested with vxlan devs in collect meta data mode with IPv4,
IPv6 and in compat mode over different network namespaces.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export flags used by eBPF helper functions through UAPI, so they can be
used by programs (instead of them redefining all flags each time or just
using the hard-coded values). It also gives a better overview what flags
are used where and we can further get rid of the extra macros defined in
filter.c. Moreover, reject invalid flags.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sz_idx variable is defined in the rtnetlink_rcv_msg(), but
not used anywhere. Let's remove it.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a generalization of the ingress qdisc as a qdisc holding
only classifiers. The clsact qdisc works on ingress, but also on egress.
In both cases, it's execution happens without taking the qdisc lock, and
the main difference for the egress part compared to prior version of [1]
is that this can be applied with _any_ underlying real egress qdisc (also
classless ones).
Besides solving the use-case of [1], that is, allowing for more programmability
on assigning skb->priority for the mqprio case that is supported by most
popular 10G+ NICs, it also opens up a lot more flexibility for other tc
applications. The main work on classification can already be done at clsact
egress time if the use-case allows and state stored for later retrieval
f.e. again in skb->priority with major/minors (which is checked by most
classful qdiscs before consulting tc_classify()) and/or in other skb fields
like skb->tc_index for some light-weight post-processing to get to the
eventual classid in case of a classful qdisc. Another use case is that
the clsact egress part allows to have a central egress counterpart to
the ingress classifiers, so that classifiers can easily share state (e.g.
in cls_bpf via eBPF maps) for ingress and egress.
Currently, default setups like mq + pfifo_fast would require for this to
use, for example, prio qdisc instead (to get a tc_classify() run) and to
duplicate the egress classifier for each queue. With clsact, it allows
for leaving the setup as is, it can additionally assign skb->priority to
put the skb in one of pfifo_fast's bands and it can share state with maps.
Moreover, we can access the skb's dst entry (f.e. to retrieve tclassid)
w/o the need to perform a skb_dst_force() to hold on to it any longer. In
lwt case, we can also use this facility to setup dst metadata via cls_bpf
(bpf_skb_set_tunnel_key()) without needing a real egress qdisc just for
that (case of IFF_NO_QUEUE devices, for example).
The realization can be done without any changes to the scheduler core
framework. All it takes is that we have two a-priori defined minors/child
classes, where we can mux between ingress and egress classifier list
(dev->ingress_cl_list and dev->egress_cl_list, latter stored close to
dev->_tx to avoid extra cacheline miss for moderate loads). The egress
part is a bit similar modelled to handle_ing() and patched to a noop in
case the functionality is not used. Both handlers are now called
sch_handle_ingress() and sch_handle_egress(), code sharing among the two
doesn't seem practical as there are various minor differences in both
paths, so that making them conditional in a single handler would rather
slow things down.
Full compatibility to ingress qdisc is provided as well. Since both
piggyback on TC_H_CLSACT, only one of them (ingress/clsact) can exist
per netdevice, and thus ingress qdisc specific behaviour can be retained
for user space. This means, either a user does 'tc qdisc add dev foo ingress'
and configures ingress qdisc as usual, or the 'tc qdisc add dev foo clsact'
alternative, where both, ingress and egress classifier can be configured
as in the below example. ingress qdisc supports attaching classifier to any
minor number whereas clsact has two fixed minors for muxing between the
lists, therefore to not break user space setups, they are better done as
two separate qdiscs.
I decided to extend the sch_ingress module with clsact functionality so
that commonly used code can be reused, the module is being aliased with
sch_clsact so that it can be auto-loaded properly. Alternative would have been
to add a flag when initializing ingress to alter its behaviour plus aliasing
to a different name (as it's more than just ingress). However, the first would
end up, based on the flag, choosing the new/old behaviour by calling different
function implementations to handle each anyway, the latter would require to
register ingress qdisc once again under different alias. So, this really begs
to provide a minimal, cleaner approach to have Qdisc_ops and Qdisc_class_ops
by its own that share callbacks used by both.
Example, adding qdisc:
# tc qdisc add dev foo clsact
# tc qdisc show dev foo
qdisc mq 0: root
qdisc pfifo_fast 0: parent :1 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc pfifo_fast 0: parent :2 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc pfifo_fast 0: parent :3 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc pfifo_fast 0: parent :4 bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1
qdisc clsact ffff: parent ffff:fff1
Adding filters (deleting, etc works analogous by specifying ingress/egress):
# tc filter add dev foo ingress bpf da obj bar.o sec ingress
# tc filter add dev foo egress bpf da obj bar.o sec egress
# tc filter show dev foo ingress
filter protocol all pref 49152 bpf
filter protocol all pref 49152 bpf handle 0x1 bar.o:[ingress] direct-action
# tc filter show dev foo egress
filter protocol all pref 49152 bpf
filter protocol all pref 49152 bpf handle 0x1 bar.o:[egress] direct-action
A 'tc filter show dev foo' or 'tc filter show dev foo parent ffff:' will
show an empty list for clsact. Either using the parent names (ingress/egress)
or specifying the full major/minor will then show the related filter lists.
Prior work on a mqprio prequeue() facility [1] was done mainly by John Fastabend.
[1] http://patchwork.ozlabs.org/patch/512949/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a small helper skb_postpush_rcsum() and fix up redirect locations
that need CHECKSUM_COMPLETE fixups on ingress. dev_forward_skb() expects
a proper csum that covers also Ethernet header, f.e. since 2c26d34bbc
("net/core: Handle csum for CHECKSUM_COMPLETE VXLAN forwarding"), we
also do skb_postpull_rcsum() after pulling Ethernet header off via
eth_type_trans().
When using eBPF in a netns setup f.e. with vxlan in collect metadata mode,
I can trigger the following csum issue with an IPv6 setup:
[ 505.144065] dummy1: hw csum failure
[...]
[ 505.144108] Call Trace:
[ 505.144112] <IRQ> [<ffffffff81372f08>] dump_stack+0x44/0x5c
[ 505.144134] [<ffffffff81607cea>] netdev_rx_csum_fault+0x3a/0x40
[ 505.144142] [<ffffffff815fee3f>] __skb_checksum_complete+0xcf/0xe0
[ 505.144149] [<ffffffff816f0902>] nf_ip6_checksum+0xb2/0x120
[ 505.144161] [<ffffffffa08c0e0e>] icmpv6_error+0x17e/0x328 [nf_conntrack_ipv6]
[ 505.144170] [<ffffffffa0898eca>] ? ip6t_do_table+0x2fa/0x645 [ip6_tables]
[ 505.144177] [<ffffffffa08c0725>] ? ipv6_get_l4proto+0x65/0xd0 [nf_conntrack_ipv6]
[ 505.144189] [<ffffffffa06c9a12>] nf_conntrack_in+0xc2/0x5a0 [nf_conntrack]
[ 505.144196] [<ffffffffa08c039c>] ipv6_conntrack_in+0x1c/0x20 [nf_conntrack_ipv6]
[ 505.144204] [<ffffffff8164385d>] nf_iterate+0x5d/0x70
[ 505.144210] [<ffffffff816438d6>] nf_hook_slow+0x66/0xc0
[ 505.144218] [<ffffffff816bd302>] ipv6_rcv+0x3f2/0x4f0
[ 505.144225] [<ffffffff816bca40>] ? ip6_make_skb+0x1b0/0x1b0
[ 505.144232] [<ffffffff8160b77b>] __netif_receive_skb_core+0x36b/0x9a0
[ 505.144239] [<ffffffff8160bdc8>] ? __netif_receive_skb+0x18/0x60
[ 505.144245] [<ffffffff8160bdc8>] __netif_receive_skb+0x18/0x60
[ 505.144252] [<ffffffff8160ccff>] process_backlog+0x9f/0x140
[ 505.144259] [<ffffffff8160c4a5>] net_rx_action+0x145/0x320
[...]
What happens is that on ingress, we push Ethernet header back in, either
from cls_bpf or right before skb_do_redirect(), but without updating csum.
The "hw csum failure" can be fixed by using the new skb_postpush_rcsum()
helper for the dev_forward_skb() case to correct the csum diff again.
Thanks to Hannes Frederic Sowa for the csum_partial() idea!
Fixes: 3896d655f4 ("bpf: introduce bpf_clone_redirect() helper")
Fixes: 27b29f6305 ("bpf: add bpf_redirect() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_release should not access dst->flags after decrementing
__refcnt to 0. The dst_entry may be in dst_busy_list and
dst_gc_task may dst_destroy it before dst_release gets a chance
to access dst->flags.
Fixes: d69bbf88c8 ("net: fix a race in dst_release()")
Fixes: 27b75c95f1 ("net: avoid RCU for NOCACHE dst")
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 538950a1b7 ("soreuseport: setsockopt SO_ATTACH_REUSEPORT_[CE]BPF")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose socket options for setting a classic or extended BPF program
for use when selecting sockets in an SO_REUSEPORT group. These options
can be used on the first socket to belong to a group before bind or
on any socket in the group after bind.
This change includes refactoring of the existing sk_filter code to
allow reuse of the existing BPF filter validation checks.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sock_reuseport is an optional shared structure referenced by each
socket belonging to a reuseport group. When a socket is bound to an
address/port not yet in use and the reuseport flag has been set, the
structure will be allocated and attached to the newly bound socket.
When subsequent calls to bind are made for the same address/port, the
shared structure will be updated to include the new socket and the
newly bound socket will reference the group structure.
Usually, when an incoming packet was destined for a reuseport group,
all sockets in the same group needed to be considered before a
dispatching decision was made. With this structure, an appropriate
socket can be found after looking up just one socket in the group.
This shared structure will also allow for more complicated decisions to
be made when selecting a socket (eg a BPF filter).
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet PHYs can maintain statistics, for example errors while idle
and receive errors. Add an ethtool mechanism to retrieve these
statistics, using the same model as MAC statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Comment says "User BPF's register A is mapped to our BPF register 6",
which is actually wrong as the mapping is on register 0. This can
already be inferred from the code itself. So just remove it before
someone makes assumptions based on that. Only code tells truth. ;)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in the days where eBPF (or back then "internal BPF" ;->) was not
exposed to user space, and only the classic BPF programs internally
translated into eBPF programs, we missed the fact that for classic BPF
A and X needed to be cleared. It was fixed back then via 83d5b7ef99
("net: filter: initialize A and X registers"), and thus classic BPF
specifics were added to the eBPF interpreter core to work around it.
This added some confusion for JIT developers later on that take the
eBPF interpreter code as an example for deriving their JIT. F.e. in
f75298f5c3 ("s390/bpf: clear correct BPF accumulator register"), at
least X could leak stack memory. Furthermore, since this is only needed
for classic BPF translations and not for eBPF (verifier takes care
that read access to regs cannot be done uninitialized), more complexity
is added to JITs as they need to determine whether they deal with
migrations or native eBPF where they can just omit clearing A/X in
their prologue and thus reduce image size a bit, see f.e. cde66c2d88
("s390/bpf: Only clear A and X for converted BPF programs"). In other
cases (x86, arm64), A and X is being cleared in the prologue also for
eBPF case, which is unnecessary.
Lets move this into the BPF migration in bpf_convert_filter() where it
actually belongs as long as the number of eBPF JITs are still few. It
can thus be done generically; allowing us to remove the quirk from
__bpf_prog_run() and to slightly reduce JIT image size in case of eBPF,
while reducing code duplication on this matter in current(/future) eBPF
JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Tested-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Zi Shen Lim <zlim.lnx@gmail.com>
Cc: Yang Shi <yang.shi@linaro.org>
Acked-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hacking tc programs with eBPF, one of the issues that come up
from time to time is to load addresses from headers. In eBPF as in
classic BPF, we have BPF_LD | BPF_ABS | BPF_{B,H,W} instructions that
extract a byte, half-word or word out of the skb data though helpers
such as bpf_load_pointer() (interpreter case).
F.e. extracting a whole IPv6 address could possibly look like ...
union v6addr {
struct {
__u32 p1;
__u32 p2;
__u32 p3;
__u32 p4;
};
__u8 addr[16];
};
[...]
a.p1 = htonl(load_word(skb, off));
a.p2 = htonl(load_word(skb, off + 4));
a.p3 = htonl(load_word(skb, off + 8));
a.p4 = htonl(load_word(skb, off + 12));
[...]
/* access to a.addr[...] */
This work adds a complementary helper bpf_skb_load_bytes() (we also
have bpf_skb_store_bytes()) as an alternative where the same call
would look like from an eBPF program:
ret = bpf_skb_load_bytes(skb, off, addr, sizeof(addr));
Same verifier restrictions apply as in ffeedafbf0 ("bpf: introduce
current->pid, tgid, uid, gid, comm accessors") case, where stack memory
access needs to be statically verified and thus guaranteed to be
initialized in first use (otherwise verifier cannot tell whether a
subsequent access to it is valid or not as it's runtime dependent).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix uninitialized variable warnings in nfnetlink_queue, a lot of
people reported this... From Arnd Bergmann.
2) Don't init mutex twice in i40e driver, from Jesse Brandeburg.
3) Fix spurious EBUSY in rhashtable, from Herbert Xu.
4) Missing DMA unmaps in mvpp2 driver, from Marcin Wojtas.
5) Fix race with work structure access in pppoe driver causing
corruptions, from Guillaume Nault.
6) Fix OOPS due to sh_eth_rx() not checking whether netdev_alloc_skb()
actually succeeded or not, from Sergei Shtylyov.
7) Don't lose flags when settifn IFA_F_OPTIMISTIC in ipv6 code, from
Bjørn Mork.
8) VXLAN_HD_RCO defined incorrectly, fix from Jiri Benc.
9) Fix clock source used for cookies in SCTP, from Marcelo Ricardo
Leitner.
10) aurora driver needs HAS_DMA dependency, from Geert Uytterhoeven.
11) ndo_fill_metadata_dst op of vxlan has to handle ipv6 tunneling
properly as well, from Jiri Benc.
12) Handle request sockets properly in xfrm layer, from Eric Dumazet.
13) Double stats update in ipv6 geneve transmit path, fix from Pravin B
Shelar.
14) sk->sk_policy[] needs RCU protection, and as a result
xfrm_policy_destroy() needs to free policies using an RCU grace
period, from Eric Dumazet.
15) SCTP needs to clone ipv6 tx options in order to avoid use after
free, from Eric Dumazet.
16) Missing kbuild export if ila.h, from Stephen Hemminger.
17) Missing mdiobus_alloc() return value checking in mdio-mux.c, from
Tobias Klauser.
18) Validate protocol value range in ->create() methods, from Hannes
Frederic Sowa.
19) Fix early socket demux races that result in illegal dst reuse, from
Eric Dumazet.
20) Validate socket address length in pptp code, from WANG Cong.
21) skb_reorder_vlan_header() uses incorrect offset and can corrupt
packets, from Vlad Yasevich.
22) Fix memory leaks in nl80211 registry code, from Ola Olsson.
23) Timeout loop count handing fixes in mISDN, xgbe, qlge, sfc, and
qlcnic. From Dan Carpenter.
24) msg.msg_iocb needs to be cleared in recvfrom() otherwise, for
example, AF_ALG will interpret it as an async call. From Tadeusz
Struk.
25) inetpeer_set_addr_v4 forgets to initialize the 'vif' field, from
Eric Dumazet.
26) rhashtable enforces the minimum table size not early enough,
breaking how we calculate the per-cpu lock allocations. From
Herbert Xu.
27) Fix FCC port lockup in 82xx driver, from Martin Roth.
28) FOU sockets need to be freed using RCU, from Hannes Frederic Sowa.
29) Fix out-of-bounds access in __skb_complete_tx_timestamp() and
sock_setsockopt() wrt. timestamp handling. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (117 commits)
net: check both type and procotol for tcp sockets
drivers: net: xgene: fix Tx flow control
tcp: restore fastopen with no data in SYN packet
af_unix: Revert 'lock_interruptible' in stream receive code
fou: clean up socket with kfree_rcu
82xx: FCC: Fixing a bug causing to FCC port lock-up
gianfar: Don't enable RX Filer if not supported
net: fix warnings in 'make htmldocs' by moving macro definition out of field declaration
rhashtable: Fix walker list corruption
rhashtable: Enforce minimum size on initial hash table
inet: tcp: fix inetpeer_set_addr_v4()
ipv6: automatically enable stable privacy mode if stable_secret set
net: fix uninitialized variable issue
bluetooth: Validate socket address length in sco_sock_bind().
net_sched: make qdisc_tree_decrease_qlen() work for non mq
ser_gigaset: remove unnecessary kfree() calls from release method
ser_gigaset: fix deallocation of platform device structure
ser_gigaset: turn nonsense checks into WARN_ON
ser_gigaset: fix up NULL checks
qlcnic: fix a timeout loop
...
Dmitry reported the following out-of-bound access:
Call Trace:
[<ffffffff816cec2e>] __asan_report_load4_noabort+0x3e/0x40
mm/kasan/report.c:294
[<ffffffff84affb14>] sock_setsockopt+0x1284/0x13d0 net/core/sock.c:880
[< inline >] SYSC_setsockopt net/socket.c:1746
[<ffffffff84aed7ee>] SyS_setsockopt+0x1fe/0x240 net/socket.c:1729
[<ffffffff85c18c76>] entry_SYSCALL_64_fastpath+0x16/0x7a
arch/x86/entry/entry_64.S:185
This is because we mistake a raw socket as a tcp socket.
We should check both sk->sk_type and sk->sk_protocol to ensure
it is a tcp socket.
Willem points out __skb_complete_tx_timestamp() needs to fix as well.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change applications monitoring FDB notifications
were not able to determine whether a new FDB entry is permament
or not:
bridge fdb add f1:f2:f3:f4:f5:f8 dev sw0p1 temp self
bridge fdb add f1:f2:f3:f4:f5:f9 dev sw0p1 self
bridge monitor fdb
f1:f2:f3:f4:f5:f8 dev sw0p1 self permanent
f1:f2:f3:f4:f5:f9 dev sw0p1 self permanent
With this change ndm_state from the original netlink message
is passed to the new netlink message sent as notification.
bridge fdb add f1:f2:f3:f4:f5:f6 dev sw0p1 self
bridge fdb add f1:f2:f3:f4:f5:f7 dev sw0p1 temp self
bridge monitor fdb
f1:f2:f3:f4:f5:f6 dev sw0p1 self permanent
f1:f2:f3:f4:f5:f7 dev sw0p1 self static
Signed-off-by: Hubert Sokolowski <hubert.sokolowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a SOCK_DESTROY operation, a destroy function
pointer to sock_diag_handler, and a diag_destroy function
pointer. It does not include any implementation code.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb_csum_offload_chk driver helper function to determine if a
device with limited checksum offload capabilities is able to offload the
checksum for a given packet.
This patch includes:
- The skb_csum_offload_chk function. Returns true if checksum is
offloadable, else false. Optionally, in the case that the checksum
is not offloable, the function can call skb_checksum_help to resolve
the checksum. skb_csum_offload_chk also returns whether the checksum
refers to an encapsulated checksum.
- Definition of skb_csum_offl_spec structure that caller uses to
indicate rules about what it can offload (e.g. IPv4/v6, TCP/UDP only,
whether encapsulated checksums can be offloaded, whether checksum with
IPv6 extension headers can be offloaded).
- Ancilary functions called skb_csum_offload_chk_help,
skb_csum_off_chk_help_cmn, skb_csum_off_chk_help_cmn_v4_only.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These netif flags are unnecessary convolutions. It is more
straightforward to just use NETIF_F_HW_CSUM, NETIF_F_IP_CSUM,
and NETIF_F_IPV6_CSUM directly.
This patch also:
- Cleans up can_checksum_protocol
- Simplifies netdev_intersect_features
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SCTP checksum is really a CRC and is very different from the
standards 1's complement checksum that serves as the checksum
for IP protocols. This offload interface is also very different.
Rename NETIF_F_SCTP_CSUM to NETIF_F_SCTP_CRC to highlight these
differences. The term CSUM should be reserved in the stack to refer
to the standard 1's complement IP checksum.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev drivers need to know the netdev on which the switchdev op was
invoked. For example, the STP state of a VLAN interface configured on top
of a port can change while being member in a bridge. In this case, the
underlying driver should only change the STP state of that particular
VLAN and not of all the VLANs configured on the port.
However, current switchdev infrastructure only passes the port netdev down
to the driver. Solve that by passing the original device down to the
driver as part of the required switchdev object / attribute.
This doesn't entail any change in current switchdev drivers. It simply
enables those supporting stacked devices to know the originating device
and act accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_reorder_vlan_header is called after the vlan header has
been pulled. As a result the offset of the begining of
the mac header has been incrased by 4 bytes (VLAN_HLEN).
When moving the mac addresses, include this incrase in
the offset calcualation so that the mac addresses are
copied correctly.
Fixes: a6e18ff111 (vlan: Fix untag operations of stacked vlans with REORDER_HEADER off)
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vladislav Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XFRM can deal with SYNACK messages, sent while listener socket
is not locked. We add proper rcu protection to __xfrm_sk_clone_policy()
and xfrm_sk_policy_lookup()
This might serve as the first step to remove xfrm.xfrm_policy_lock
use in fast path.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cgroup v1, dealing with cgroup membership was difficult because the
number of membership associations was unbound. As a result, cgroup v1
grew several controllers whose primary purpose is either tagging
membership or pull in configuration knobs from other subsystems so
that cgroup membership test can be avoided.
net_cls and net_prio controllers are examples of the latter. They
allow configuring network-specific attributes from cgroup side so that
network subsystem can avoid testing cgroup membership; unfortunately,
these are not only cumbersome but also problematic.
Both net_cls and net_prio aren't properly hierarchical. Both inherit
configuration from the parent on creation but there's no interaction
afterwards. An ancestor doesn't restrict the behavior in its subtree
in anyway and configuration changes aren't propagated downwards.
Especially when combined with cgroup delegation, this is problematic
because delegatees can mess up whatever network configuration
implemented at the system level. net_prio would allow the delegatees
to set whatever priority value regardless of CAP_NET_ADMIN and net_cls
the same for classid.
While it is possible to solve these issues from controller side by
implementing hierarchical allowable ranges in both controllers, it
would involve quite a bit of complexity in the controllers and further
obfuscate network configuration as it becomes even more difficult to
tell what's actually being configured looking from the network side.
While not much can be done for v1 at this point, as membership
handling is sane on cgroup v2, it'd be better to make cgroup matching
behave like other network matches and classifiers than introducing
further complications.
In preparation, this patch updates sock->sk_cgrp_data handling so that
it points to the v2 cgroup that sock was created in until either
net_prio or net_cls is used. Once either of the two is used,
sock->sk_cgrp_data reverts to its previous role of carrying prioidx
and classid. This is to avoid adding yet another cgroup related field
to struct sock.
As the mode switching can happen at most once per boot, the switching
mechanism is aimed at lowering hot path overhead. It may leak a
finite, likely small, number of cgroup refs and report spurious
prioidx or classid on switching; however, dynamic updates of prioidx
and classid have always been racy and lossy - socks between creation
and fd installation are never updated, config changes don't update
existing sockets at all, and prioidx may index with dead and recycled
cgroup IDs. Non-critical inaccuracies from small race windows won't
make any noticeable difference.
This patch doesn't make use of the pointer yet. The following patch
will implement netfilter match for cgroup2 membership.
v2: Use sock_cgroup_data to avoid inflating struct sock w/ another
cgroup specific field.
v3: Add comments explaining why sock_data_prioidx() and
sock_data_classid() use different fallback values.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Daniel Wagner <daniel.wagner@bmw-carit.de>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce sock->sk_cgrp_data which is a struct sock_cgroup_data.
->sk_cgroup_prioidx and ->sk_classid are moved into it. The struct
and its accessors are defined in cgroup-defs.h. This is to prepare
for overloading the fields with a cgroup pointer.
This patch mostly performs equivalent conversions but the followings
are noteworthy.
* Equality test before updating classid is removed from
sock_update_classid(). This shouldn't make any noticeable
difference and a similar test will be implemented on the helper side
later.
* sock_update_netprioidx() now takes struct sock_cgroup_data and can
be moved to netprio_cgroup.h without causing include dependency
loop. Moved.
* The dummy version of sock_update_netprioidx() converted to a static
inline function while at it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netprio builds per-netdev contiguous priomap array which is indexed by
css->id. The array is allocated using kzalloc() effectively limiting
the maximum ID supported to some thousand range. This patch caps the
maximum supported css->id to USHRT_MAX which should be way above what
is actually useable.
This allows reducing sock->sk_cgrp_prioidx to u16 from u32. The freed
up part will be used to overload the cgroup related fields.
sock->sk_cgrp_prioidx's position is swapped with sk_mark so that the
two cgroup related fields are adjacent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the kernel generally uses negated error numbers, *err needs to be
compared with -EAGAIN (d'oh).
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Fixes: ea3793ee29 ("core: enable more fine-grained datagram reception control")
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit which went into mainline through networking tree
3b13758f51 ("cgroups: Allow dynamically changing net_classid")
conflicts in net/core/netclassid_cgroup.c with the following pending
fix in cgroup/for-4.4-fixes.
1f7dd3e5a6 ("cgroup: fix handling of multi-destination migration from subtree_control enabling")
The former separates out update_classid() from cgrp_attach() and
updates it to walk all fds of all tasks in the target css so that it
can be used from both migration and config change paths. The latter
drops @css from cgrp_attach().
Resolve the conflict by making cgrp_attach() call update_classid()
with the css from the first task. We can revive @tset walking in
cgrp_attach() but given that net_cls is v1 only where there always is
only one target css during migration, this is fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nina Schiff <ninasc@fb.com>
The __skb_recv_datagram routine in core/ datagram.c provides a general
skb reception factility supposed to be utilized by protocol modules
providing datagram sockets. It encompasses both the actual recvmsg code
and a surrounding 'sleep until data is available' loop. This is
inconvenient if a protocol module has to use additional locking in order
to maintain some per-socket state the generic datagram socket code is
unaware of (as the af_unix code does). The patch below moves the recvmsg
proper code into a new __skb_try_recv_datagram routine which doesn't
sleep and renames wait_for_more_packets to
__skb_wait_for_more_packets, both routines being exported interfaces. The
original __skb_recv_datagram routine is reimplemented on top of these
two functions such that its user-visible behaviour remains unchanged.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov