netprio builds per-netdev contiguous priomap array which is indexed by
css->id. The array is allocated using kzalloc() effectively limiting
the maximum ID supported to some thousand range. This patch caps the
maximum supported css->id to USHRT_MAX which should be way above what
is actually useable.
This allows reducing sock->sk_cgrp_prioidx to u16 from u32. The freed
up part will be used to overload the cgroup related fields.
sock->sk_cgrp_prioidx's position is swapped with sk_mark so that the
two cgroup related fields are adjacent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0d76d6e8b2 and merge
commit c402293bd7, reversing changes made
to c89359a42e.
The virtio-vsock device specification is not finalized yet. Michael
Tsirkin voiced concerned about merging this code when the hardware
interface (and possibly the userspace interface) could still change.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
sh_eth: optimize MDIO code
Here's a set of 3 patches against DaveM's 'net-next.git' repo which
gets rid of ~35 LoCs in the MDIO bitbang methods.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After the MDIO bitbang code consolidation, there's no need anymore for
bb_{set|clr}() as well as bb_read() -- just expand them inline, thus
saving more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mm[cd]_ctrl() and sh_set_mdio() all look mostly the same -- factor out
their common code and put it into sh_mdio_ctrl().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO control bits are always mapped to the same bits of the same register
(PIR), so there's no need to store their masks in the 'struct bb_info'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgene_mac_ops and xgene_port_ops structures are never modified, so
declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWZcQtAAoJEG4XJFUm622bgcMH/1VRwtzAKpYVwAyAN0MtVLxe
uANi0Pw1PmEAeEI3TxEBckEH0JYfpg+aAwX7S8scnQSvLP3FYeC5IcHG551vlh0s
FlkGexcXqGrDqjt8mz8hxqqAmMH9YEVlzj2HJf6YFjNS4K84CEgpaSjaSG8S7Wc8
hTSA5K+XxrnEeX41W7FYmeBFLejisg0gVTkS3ZCe4qYz4Gh1oamoA0pOdU+AYOMy
0XBkCT8fqTVXWLHh9/+J7IZOYrjBl4rVaHofeygEAfSRNNfmmjZXX1R+FCQoJEZC
IOEQ31T64G4A37t2N2RGOhiG+2vckdbPg2JsqJosI1L2OZSBbeGZsVW48w+5cgc=
=GQDA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Vallo says:
====================
brcfmac
* support bcm4359 which can operate in two bands concurrently
* disable runtime pm for USB avoiding issues
* use generic pm callback in PCIe driver
* support wowlan wake indication reporting
* add beamforming support
* unified handling of firmware files
ath10k
* support Manegement Frame Protection (MFP)
* add thermal throttling support for 10.4 firmware
* add support for pktlog in QCA99X0
* add debugfs file to enable Bluetooth coexistence feature
* use firmware's native mesh interface type instead of raw mode
iwlwifi
* BT coex improvements
* D3 operation bugfixes
* rate control improvements
* firmware debugging infra improvements
* ground work for multi Rx
* various security fixes
====================
Conflicts:
drivers/net/wireless/ath/ath10k/pci.c
The conflict resolution at:
http://article.gmane.org/gmane.linux.kernel.next/37391
by Stephen Rothwell was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
As the kernel generally uses negated error numbers, *err needs to be
compared with -EAGAIN (d'oh).
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Fixes: ea3793ee29 ("core: enable more fine-grained datagram reception control")
Signed-off-by: David S. Miller <davem@davemloft.net>
the simple_strtoul function is obsolete. This patch replace it by
kstrtox.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong says:
====================
Further fix for dsa unbinding
This series fixes further issues for DSA dynamic unbinding.
The first patch completely removes the PHY link state polling.
The two following cleans up the dsa state upon removal.
The last patch moves slave destroy code as slave function and
adds missing netdev and phy cleanup calls.
v1: http://lkml.kernel.org/r/562F8ECB.6050709@baylibre.com
v2: http://lkml.kernel.org/r/56321D9A.8010109@baylibre.com
remove phy fix and add missing calls in dsa_switch_destroy
then add dedicated dsa_slave_destroy
v3: remove polling instead of fixing it, make single patch for
dsa slave destroy
====================
Acked-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dsa slave dedicated code from dsa_switch_destroy to a new
dsa_slave_destroy function in slave.c.
Add the netif_carrier_off and phy_disconnect calls in order to
correctly cleanup the netdev state and PHY state machine.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon probe failure or unbinding, add missing dev_put() calls.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we unassign the master_netdev dsa_ptr to make the packet
processing go through the regular Ethernet receive path.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since no more DSA driver uses the polling callback, and since
the phylib handles the link detection, remove the link polling
work and timer code.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
-----BEGIN PGP SIGNATURE-----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=+5dd
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This pull request got a bit bigger than I wanted, due to
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham says:
====================
net: thunderx: Miscellaneous cleanups
This patch series contains contains couple of cleanup patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have moved on to using allocated pages to carve receive
buffers instead of netdev_alloc_skb() there is no need to store
any pointers for later retrieval. Earlier we had to store
skb and skb->data pointers which later are used to handover
received packet to network stack.
This will avoid an unnecessary cache miss as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same switch-case repeates for nivc_*_intr functions.
In this patch it is moved to a helper nicvf_int_type_to_mask().
By the way:
- Unneeded write to NICVF register dropped if int_type is unknown.
- netdev_dbg() is used instead of netdev_err().
Signed-off-by: Yury Norov <yury.norov@auriga.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Acked-by: Vadim Lomovtsev <Vadim.Lomovtsev@caiumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of HW ROC, when the driver reports that the ROC expired,
it is not sufficient to purge the ROCs based on the remaining
time, as it possible that the device finished the ROC session
before the actual requested duration.
To handle such cases, in case of ROC expired notification from
the driver, complete all the ROCs which are marked with hw_begun,
regardless of the remaining duration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current unix_dgram_recvsmg code acquires the u->readlock mutex in
order to protect access to the peek offset prior to calling
__skb_recv_datagram for actually receiving data. This implies that a
blocking reader will go to sleep with this mutex held if there's
presently no data to return to userspace. Two non-desirable side effects
of this are that a later non-blocking read call on the same socket will
block on the ->readlock mutex until the earlier blocking call releases it
(or the readers is interrupted) and that later blocking read calls
will wait longer than the effective socket read timeout says they
should: The timeout will only start 'ticking' once such a reader hits
the schedule_timeout in wait_for_more_packets (core.c) while the time it
already had to wait until it could acquire the mutex is unaccounted for.
The patch avoids both by using the __skb_try_recv_datagram and
__skb_wait_for_more packets functions created by the first patch to
implement a unix_dgram_recvmsg read loop which releases the readlock
mutex prior to going to sleep and reacquires it as needed
afterwards. Non-blocking readers will thus immediately return with
-EAGAIN if there's no data available regardless of any concurrent
blocking readers and all blocking readers will end up sleeping via
schedule_timeout, thus honouring the configured socket receive timeout.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __skb_recv_datagram routine in core/ datagram.c provides a general
skb reception factility supposed to be utilized by protocol modules
providing datagram sockets. It encompasses both the actual recvmsg code
and a surrounding 'sleep until data is available' loop. This is
inconvenient if a protocol module has to use additional locking in order
to maintain some per-socket state the generic datagram socket code is
unaware of (as the af_unix code does). The patch below moves the recvmsg
proper code into a new __skb_try_recv_datagram routine which doesn't
sleep and renames wait_for_more_packets to
__skb_wait_for_more_packets, both routines being exported interfaces. The
original __skb_recv_datagram routine is reimplemented on top of these
two functions such that its user-visible behaviour remains unchanged.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device tree properties for a phy device are expected to be in the phy
node. The current code for the DP83867 also tries to look in the
parent node. The devices binding documentation does not mention this,
no current device tree file makes use of this, and it is not behaviour
we want. So remove looking in the parent device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a writable sysfs attribute for the "NDP to end"
quirk flag.
This makes it easier for end users to test new devices for
this firmware bug. We've been lucky so far, but we should
not depend on reporters capable of rebuilding the driver.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
Add HA and LAG support for mlx4 SRIOV VFs
This series is built upon the code added in commit ce388ff "Merge branch
'mlx4-next'" which added HA and LAG support to mlx4 RoCE and SRIOV services.
We add HA and Link Aggregation support to single ported mlx4 Ethernet VFs.
In this case, the PF Ethernet interfaces are bonded, the VFs see single
port HW devices (already supported) -- however, now this port is highly
available. This means that all VF HW QPs (both VF Ethernet driver and VF
RoCE / RAW QPs) are subject to the V2P (Virtual-To-Physical) mapping which
is managed by the PF driver, and hence resilient across link failures and
such events.
When bonding operates in Dynamic link aggregation (802.3ad) mode, traffic
from each VF will go over the VF "base port" (the port this VF is assigned
to by the admin) as long as this port is up. When the port fails, traffic
from all VFs that are defined on this port will move to the other port, and
be back to their base-port when it recovers.
Moni and Or.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mlx4 driver runs in HA mode, and all VFs are single ported
ones, we make their single port Highly-Available.
This is done by taking advantage of the HA mode properties (following
bonding changes with programming the port V2P map, etc) and adding
the missing parts which are unique to SRIOV such as mirroring VF
steering rules on both ports.
Due to limits on the MAC and VLAN table this mode is enabled only when
number of total VFs is under 64.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, it's possible that the VF registered its GID
(and expects to get mads through the PV scheme) on a port which is
different from the one this mad arrived on, due to HA fail over.
Therefore, if the gid is not matched on the port that the packet arrived
on, check for a match on the other port if HA mode is active -- and if a
match is found on the other port, continue processing the mad using that
other port.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW limitations, indexes to MAC and VLAN tables are always taken
from the table of the actual port. So, if a resource holds an index to
a table, it may refer to different values during the lifetime of the
resource, unless the tables are mirrored. Also, even when
driver is not in HA mode the policy of allocating an index to these
tables is such to make sure, as much as possible, that when the time
comes the mirroring will be successful. This means that in multifunction
mode the allocation of a free index in a port's table tries to make sure
that the same index in the other's port table is also free.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, steering rules set by VFs should be mirrored on both
ports of the device so packets will be accepted no matter on which
port they arrived.
Since getting into HA mode is done dynamically when the user bonds mlx4
Ethernet netdevs, we keep hold of the VF DMFS rule mbox with the port
value flipped (1->2,2->1) and execute the mirroring when getting into
HA mode. Later, when going out of HA mode, we unset the mirrored rules.
In that context note that mirrored rules cannot be removed explicitly.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under HA mode, the link down event should be sent to VFs only if both
ports are down.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HA mode, the link state for VFs for which the policy is "auto"
(i.e. follow the physical link state) should be ORed from both ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unneeded variable used to store return value.
Generated by: scripts/coccinelle/misc/returnvar.cocci
CC: Asias He <asias@redhat.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier calls were thrown in as a last-minute fix for an
imagined "this device could be part of a bridge" problem. That
revealed a certain lack of locking. Not to mention testing...
Avoid this splat:
RTNL: assertion failed at net/core/dev.c (1639)
CPU: 0 PID: 4293 Comm: bash Not tainted 4.4.0-rc3+ #358
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
0000000000000000 ffff8800ad253d60 ffffffff8122f7cf ffff8800ad253d98
ffff8800ad253d88 ffffffff813833ab 0000000000000002 ffff880230f48560
ffff880230a12900 ffff8800ad253da0 ffffffff813833da 0000000000000002
Call Trace:
[<ffffffff8122f7cf>] dump_stack+0x4b/0x63
[<ffffffff813833ab>] call_netdevice_notifiers_info+0x3d/0x59
[<ffffffff813833da>] call_netdevice_notifiers+0x13/0x15
[<ffffffffa09be227>] raw_ip_store+0x81/0x193 [qmi_wwan]
[<ffffffff8131e149>] dev_attr_store+0x20/0x22
[<ffffffff811d858b>] sysfs_kf_write+0x49/0x50
[<ffffffff811d8027>] kernfs_fop_write+0x10a/0x151
[<ffffffff8117249a>] __vfs_write+0x26/0xa5
[<ffffffff81085ed4>] ? percpu_down_read+0x53/0x7f
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81174c9e>] ? __sb_start_write+0x5f/0xb0
[<ffffffff81172c37>] vfs_write+0xa3/0xe7
[<ffffffff811734ad>] SyS_write+0x50/0x7e
[<ffffffff8145c517>] entry_SYSCALL_64_fastpath+0x12/0x6f
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8fe269991a.
The case where VXLAN is a module and i40e driver is inbuilt
will not be handled properly with this change since i40e
will have an undefined symbol vxlan_get_rx_port in it.
v2: Add a signed-off-by.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2015-12-05
This series contains updates to fm10k only.
Jacob provides the remaining fm10k patches in the series. First change
ensures that all the logic regarding the setting of netdev features is
consolidated in one place of the driver. Fixed an issue where an assumption
was being made on how many queues are available, especially when init_hw_vf()
errors out. Fixed up an number of issues with init_hw() where failures
were not being handled properly or at all, so update the driver to check
returned error codes and respond appropriately. Fixed up typecasting
issues found where either the incorrect typecast size was used or
explicitly typecast values. Added additional debugging statistics and
rename statistic to better reflect its true value. Added support for
ITR scaling based on PCIe link speed for fm10k. Fixed up code comment
where "hardware" was misspelled.
v2: Dropped patches #1 and #10 from original submission, patch #1 was from
Nick Krause and due to his past kernel interactions, dropping his patch.
Patch #10 had questions and concerns from Tom Herbert which cannot be
addressed at this time since the author (Jacob Keller) is currently on
sabbatical, so dropping this patch for now until we can properly address
Tom's questions and concerns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default ITR for Tx is overly restrictive. Using a simple
netperf TCP_STREAM test, we top out at about 10Gb/s for a single thread
when running using 1500 byte frames. By reducing the ITR value to 25usec
(up to 40K interrupts a second from 10K), we are able to achieve 36Gb/s
for a single thread TCP stream test.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Reported-by: Alex Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Define a macro for identifying when the itr value is dynamic or
adaptive. The concept was taken from i40e. This helps make clear what
the check is, and reduces the line length to something more reasonable
in a few places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Intel Ethernet Switch FM10000 Host Interface interrupt throttle
timers are based on the PCIe link speed. Because of this, the value
being programmed into the ITR registers must be scaled accordingly.
For the PF, this is as simple as reading the PCIe link speed and storing
the result. However, in the case of SR-IOV, the VF's interrupt throttle
timers are based on the link speed of the PF. However, the VF is unable
to get the link speed information from its configuration space, so the
PF must inform it of what scale to use.
Rather than pass this scale via mailbox message, take advantage of
unused bits in the TDLEN register to pass the scale. It is the
responsibility of the PF to program this for the VF while setting up the
VF queues and the responsibility of the VF to get the information
accordingly. This is preferable because it allows the VF to set up the
interrupts properly during initialization and matches how the MAC
address is passed in the TDBAL/TDBAH registers.
Since we're modifying fm10k_type.h, we may as well also update the
copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally this statistic was renamed because the method of dropping was
called "drop_oversized_messages", but this logic has changed much, and
this counter does actually represent messages which we failed to
transmit for a number of reasons. Rename the counter back to tx_dropped
since this is when it will increment, and it is less confusing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous bug was uncovered by addition of a debug stat to indicate the
actual number of DWORDS we pulled from the mbmem. It turned out this was
not the same as the tx_dwords counter. While the previous bug fix should
have corrected this in all cases, add some debug stats that count the
number of DWORDs pushed or pulled from the mbmem. A future debugger may
take advantage of this statistic for debugging purposes. Since we're
modifying fm10k_mbx.h, update the copyright year as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the resultant data type of the mac_update.mac_upper field is u16,
it does not make sense to typecast u8 variables to u32 first. Since
we're modifying fm10k_pf.c, also update the copyright year.
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.
Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.
In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.
Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers must detect how many queues are available. Previously, the
driver assumed that each VF has at minimum 1 queue. This assumption is
incorrect, since it is possible that the PF has not yet assigned the
queues to the VF by the time the VF checks. To resolve this, we added a
check first to ensure that the first queue is infact owned by the VF at
init_hw_vf time. However, the code flow did not reset hw->mac.max_queues
to 0. In some cases, such as during reinit flows, we call init_hw_vf
without clearing the previous value of hw->mac.max_queues. Due to this,
when init_hw_vf errors out, if its error code is not properly handled
the VF driver may still believe it has queues which no longer belong to
it. Fix this by clearing the hw->mac.max_queues on exit due to errors.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tejun Heo