* fix/hda:
ALSA: hda - Add sanity check in PCM open callback
ALSA: hda - Call snd_pcm_lib_hw_rates() again after codec open callback
ALSA: hda - Avoid invalid formats and rates with shared SPDIF
ALSA: hda - Improve ASUS eeePC 1000 mixer
ALSA: hda - Add GPIO1 control at muting with HP laptops
Add some sanity checks of struct snd_pcm_hardware fields in the PCM
open callback of hda driver. This makes a bit easier to debug any PCM
setup errors in the codec side.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM rates bit field may have been changed by the codec open callback.
In that case, we need to reset rate_min and rate_max. So, simply call
snd_pcm_lib_hw_rates() again after the codec open callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing. If any of them can be zero, disable
the SPDIF sharing mode instead. Otherwise it will lead to a PCM
configuration error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer elements created for ASUS eeePC 1000 with ALC269 aren't
standard but strange words like "LineOut". Rename the element names
to follow the standard one like "Headphone" and "Speaker".
Also, split the volumes to each so that the virtual master can control
them.
The alc269_fujitsu_mixer is removed because it's now identical with
the new eeepc mixer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP laptops with AD1984A codecs (at least mobile models) need to set
GPIO1 appropriately to indicate the mute state. The BIOS checks this
bit to judge whether the mute on or off is sent via F8 key.
Without changing this bit, the BIOS can be confused and may toggle
the mute wrongly.
Reference: Novell bnc#515266
https://bugzilla.novell.com/show_bug.cgi?id=515266
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the changes to clean up / fix the realtek codec initialization
routines in commit 4a79ba34ca,
I forgot to add the check for ALC268 and ALC269.
This resulted in the missing EAPD and COEF setup for these codecs.
This patch adds the missing checks for these codecs.
Reference: bko#13633
http://bugzilla.kernel.org/show_bug.cgi?id=13633
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Line In connector is set up as PIN_IN by default, using
VREF_HIZ. It is connected to both ADCs, so add it to both
input selectors.
Also add the ability to use the input mix (on a SoundBlaster
one would call this "What You Hear").
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the following bugs of acer-aspire-6530g model with ALC888:
- HP jack to mute all speaker outputs including LFE
- Make digital built-in mic working
Signed-off-by: Emilio López <buhitoescolar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Realtek codecs require the pin-sense trigger call before actually
reading the pin-sense. Without this, the pin-detection might not be
done accurately.
This patch adds the pin-capability check and issues the trigger call
if required.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Samsung P50 requires the HP auto-muting unlike other Samsung models.
Added a new model=samsung-p50 to support this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to ad_spec struct so that the same hack can be used for
any other models (if any). This also allows other models to reuse the
auto-mute functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split mixer element arrays of AD1986A models to several pieces so that
each model can share the same mixer arrays.
This removes lots of duplicated data.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the jack-plug notification via input layer selectable via Kconfig.
This is often unnecessary, and the similr function will be provided
using the ALSA control API in near future anyway.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the digital-mic support with ALC262 auto model.
The new ALC262 models have the digital mic at NID 0x12. This widget
isn't checked in the current alc262_auto_create_analog_input_ctls()
since it's under 0x18. So, just reuse the routine for alc269 to fix
the behavior.
But, it doesn't suffice: the digital mic is supported only with the
ADC0, we have to exclude other ADCs when d-mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the check of the input-source type by checking the widget type of
each capture-source item. Since some codecs can have both the mixer
and selector types depending on the ADC, alc_mux_enum_put() needs to
check each widget.
With this change, spec->capture_style gets unneeded, so it's removed,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit f9e336f65b
ALSA: hda - Unify capture mixer creation in realtek codes
removed the "Input Source" mixer element creation for toshiba-s06 model
because it contains a digital-mic input.
This patch take the control back.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Fix the comparison of unsigned int that causes a compile warning below
by changing to the right signed type:
patch_sigmatel.c: In function ‘stac92xx_vref_set’:
patch_sigmatel.c:658: warning: comparison of unsigned expression < 0 is always false
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The selected 4930G model seemed to keep the subwoofer 'tuba'
function from operating correctly. Removing the existing PCI
ID match made this work again, but it was mapped to 'Side'
instead of to LFE as one would expect.
This attempts to enable all functionality and keep the amount
of available mixer sliders low. Any slider that had no audible
effect on the output audio has been removed, and as such EAPD
is not currently enabled.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct some cut+paste typos from 'tagra' to 'targa'.
Signed-off-by: Sasha Alexandr <brina_keith@ns.sympatico.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added 7.1 support for MSI GX620 and jack quirk.
Reference: kernel bug#13430
http://bugzilla.kernel.org/show_bug.cgi?id=13430
Signed-off-by: David Heidelberger <d.okias@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
with BIOS probing only we offer a non functional headphone swith and
volume slider.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input
Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.
Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)
Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).
Tested working: Three capture channels, mic in, line in, DMIC.
Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.
Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver. This seems unable to be recovered without the controller
reset.
This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, LG R510 is only able to produce sound on headphones, the
internal speakers are not working.
The user tested and confirmed that with model=Dell headphones,
internal speakers and the microphone are working flawlessly.
Tested-by: Serdar Soytetir <tulliana@gmail.com>
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this is a patch against current snapshot that adds:
6 channels support for the MB5 model
Signed-off-by: Kacper Szczesniak <kacper@qwe.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix issues for 3 generations of HP workstations.
The modest modifications do the following:
1. Change the second MIC from device 3 to device 1
2. Init the "boost" values to "0" by default
From: John Brown <john.brown3@hp.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch changes Line In as Out Switch and Mic In as Out Switch to
enums for consistency, and causes all mic and line in ports to be probed
and controls to be added appropriately.
Signed-off-by: Nickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9c1. This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai