PCM platform driver binds to the platform device created by ACP3x PCI
device. PCM driver registers ALSA DMA and CPU DAI components with ASoC
framework.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP 3x IP has I2S controller device as one of IP blocks.
Create a platform device for it, so that the PCM platform driver
can be bound to this device. Pass PCI resources like MMIO, irq
to the platform device.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <vishnuvardhanrao.ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP 3.0 is a PCI audio device. This patch adds PCI driver to bind
to this device and get PCI resources.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Sanju R Mehta <sanju.mehta@amd.com>
Tested-by: Ravulapati Vishnu vardhan Rao <Vishnuvardhanrao.Ravulapati@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP 3.x is a new audio block in raven. Added register header
of the same.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Vijendar Mukunda <vijendar.mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On certain platforms, Display HDMI HDA codec was not going to sleep state
after the use when links are powered down after turning off the display
power. As per the HW recommendation, links are powered down before turning
off the display power to ensure that the codec goes to sleep state.
This patch was updated from an earlier version submitted upstream [1]
which conflicted with the changes merged for HDaudio codec support
with the Intel DSP.
[1] https://patchwork.kernel.org/patch/10540213/
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Icelake device id. Also, Icelake's pin2port mapping table is
complicated. So we use a mapping table to do the pin2port mapping.
Signed-off-by: Bard liao <bard.liao@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the duplicated initialization statements from
wm_adsp1_init() and wm_adsp2_init() into new function
wm_adsp_common_init().
The entire content of wm_adsp1_init() is the common code
but it is convenient to retain this exported function
to hide what we currently treat as common init (which might
change in the future) and also make clear the difference
between an ADSP1 entry point and common code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stack memory isn't DMA-safe so it isn't safe to use either
regmap_raw_read or regmap_bulk_read to read into stack memory.
The two functions to read the scratch registers were using
stack memory and regmap_raw_read. It's not worth allocating
memory just for this trivial read, and it isn't time-critical.
A simple regmap_read for each register is sufficient.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing prepare_sleve_config that is needed for
setup the DMA slave channel for I2S.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initializing to -EINVAL is not correct as the variables are unsigned and
if buffer_size is 0 then they are not used anyway.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver will not probe if the pdata is not provided or created.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mcbsp.c was copied a while back from arch/arm/plat-omap/mcbsp.c and it
contained a mix of McBSP and McBSP sidetone functions.
Create new file structure with the following split:
omap-mcbsp.c - McBSP related functions
omap-mcbsp-st.c - McBSP sidetone functionality
omap-mcbsp-priv.h - Private header for internal use
omap-mcbsp.h - Header for user drivers
I have tried to do the code move with minimal code change, cleanup patches
can be based on the new structure.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if the McBSP have FIFO in the omap_mcbsp_set_threshold() and
omap_mcbsp_dai_delay() delay function to skip calling the lower layer if
it is not needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We either start/stop TX or RX, never both. Move the tx/rx direction
selection within the functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The parameter name of dev_id is leftover from the old times when we passed
numeric ID as data for the interrupt handlers.
The mcbsp_rx and mcbsp_tx is misleading as they are pointers to the mcbsp
struct.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is configured runtime so no need to initialize it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the omap_mcbsp_dma_reg_params() a bit more intuitive to read for the
first glance by using SNDRV_PCM_STREAM_PLAYBACK/CAPTURE and to group the
outermost if case by stream direction.
While there, fix the outdated comment for the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit c0ea089dba ("ASoC: rsnd: rsnd_mod_name() handles both name and
ID") merged "name" and "ID" on rsnd_mod_name() to handle sub-ID
(= for CTU/BUSIF).
Then, it decided to share static char to avoid pointless memory.
But, it doesn't work correctry in below case, because last called
name will be used.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssi[0] is connected to ssi[0]
~~~~~~ ~~~~~~
We still don't want to have pointless memory, so let's use ring buffer.
16byte x 5 is very enough for this purpose.
dev_xxx(dev, "%s is connected to %s\n",
rsnd_mod_name(mod_a), /* ssiu[00] */
rsnd_mod_name(mod_b)); /* ssi[0] */
->
rcar_sound ec500000.sound: ssiu[00] is connected to ssi[0]
~~~~~~~~ ~~~~~~
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drvdata is actually sun8i_codec, not snd_soc_card, so it crashes
when calling snd_soc_card_get_drvdata().
Drop card and scodec vars anyway since we don't need to
disable/unprepare clocks - it's already done by calling
runtime_suspend()
Drop clk_disable_unprepare() calls for the same reason.
Fixes: 36c684936f ("ASoC: Add sun8i digital audio codec")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen2 has BUSIF0-3, Gen3 has BUSIF0-7 on some SSIU.
Current driver is assuming it is using BUSIF0 as default.
Thus, SSI is attaching SSIU (with BUSIF0) by using rsnd_ssiu_attach().
But, TDM split mode also needs other BUSIF to use it.
This patch adds missing SSIU BUSIFx support.
BUSIF is handled by SSIU instead of SSI anymore.
Thus, its settings no longer needed on SSI node on DT.
This patch removes its settings from Document, but driver is still
keeping compatibility. Thus, old DT style is still working.
But, to avoid confusing, it doesn't indicate old compatibility things on
Document. New SoC should have SSIU on DT from this patch.
1) old style DT is still supported (= no rcar_sound,ssiu node on DT)
2) If ssiu is not indicated on playback/capture,
BUSIF0 will be used as default
playback = <&ssi3>; /* ssiu30 will be selected */
3) you can select own ssiu
playback = <&ssi32 &ssi3>; /* ssiu32 will be selected */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
converted rate/chan are handled each rated module, but
it will be used other module too.
For examle, converted channel is currently used for CTU,
but, it will be used for TDM Split mode, too.
This patch move/merge SRC/CTU hw_param under core.c
and handles converted rate/chan under rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver is supporting HDMI output, and its information
are handled under ssi.c. But, it is stream information.
Let's move it from ssi.c to core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rdai->playback/rdai->capture are defined as io_playback/io_capture
on __rsnd_dai_probe(). Let's use it instead of original one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has rsnd_runtime_is_ssi_xxx() functions,
but it is not only related to SSI, thus, it is misunderstandable.
This patch renames it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DTC commit df536831d02c ("checks: add graph binding checks")
is checking endpoint bidirectional, and it is upstreamed to linux by
commit 50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc").
Let's remove own bidirectional check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver is checking situation that can not happen.
This patch removes over-kill check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DTC commit df536831d02c ("checks: add graph binding checks")
is checking endpoint bidirectional, and it is upstreamed to linux by
commit 50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc").
Let's remove own bidirectional check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DTC commit df536831d02c ("checks: add graph binding checks")
is checking endpoint bidirectional, and it is upstreamed to linux by
commit 50aafd6089 ("scripts/dtc: Update to upstream version
v1.4.6-21-g84e414b0b5bc").
Let's remove own bidirectional check
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the RVP/LeafHill SSDT exposes an INT34C3 ID which is
used on other boards to point to the TDF8532 amplifier. Yay BIOS.
Add a DMI-quirk to ignore this ID and check for other valid machine
driver descriptors.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add firmware/topology information for APL RVP
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bard liao <bard.liao@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GFP_ATOMIC is not required on any Intel drivers, use GFP_KERNEL
instead. A first cleanup was merged in April but missed a number
occurrences and new ones were added by copy/paste inertia.
While we are at it, make checkpatch happy with a sizeof(*msg)
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
s/skylaye/skylake
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't rely on internal Atom/SST-specific data structures, use
generic interface to let other drivers use the same machine drivers
as is, e.g. SOF to support BYT-CR devices
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't rely on internal Skylake-specific data structures, use
generic interface to let other drivers use the same machine driver
as is, e.g. SOF to support HDaudio codecs and HDMI outputs.
Tested on LeafHill CRB board, no regression seen with this change.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling both the old AC97_BUS code and the new AC97_BUS_COMPAT causes
problems because both modules provide an exported snd_ac97_reset()
function.
I had tried to fix the problem of having both coexist earlier, but
my patch only prevented them from being built-in. This is because
of a special Kconfig feature that lets a symbol have a dependency
on another one being disabled, but still allow both to be loadable
modules.
Changing the dependency to =n avoids that problem, now we can only
build the new driver if the old one is completely disabled.
If we could figure out a way to let rename one of the reset
functions and have each driver link to exactly the old or
the compat code, that would also work, but I could not find if
that's possible.
Fixes: bec5ecdf41 ("ASoC: pxa: avoid AC97_BUS build warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio support is done via simple-audio-card via DT, the custom driver
is no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DACn Zero Flag" and "ADCn Overflow Flag" are read-only status
register. These information are needed for driver not for user.
Let's remove these from snd_kcontrol_new.
There is no detail explanation for these register on
datasheet, but, judging from its behavior, it seems these register
needs clock to read. Otherwise, I2C returns error.
Therefor, amixer command will be failed under non working timing.
Without this patch, user often fail amixer command.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_component_update_bits() will only update the mask bits,
so remove the redundant snd_soc_component_read32().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the dapm widgets are incorrectly defined from the start,
Not sure how we ended up with such thing. Fix them now!
Without this fix the backend dais are always powered up even if there
is no active stream.
Reported-by: Jimmy Cheng-Yi Chiang <cychiang@google.com>
Reported-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
q6asm routing gets added multiple times as part of dai probe.
Move this to q6routing routes which has those widgets defined, this also
fixes the issue where these are added each time at dai probe.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SD line mask for MI2S starts from BIT 0 instead of BIT 1.
Fix all bit mask for MI2S SD lines.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards such as the Swanky model Chromebooks use pmc_plt_clk_0 for the
mclk instead of pmc_plt_clk_3.
This commit adds a DMI based quirk for this.
This fixing audio no longer working on these devices after
commit 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
that commit fixes us unnecessary keeping unused clocks on, but in case
of the Swanky that was breaking audio support since we were not using
the right clock in the cht_bsw_max98090_ti machine driver.
Cc: stable@vger.kernel.org
Fixes: 648e921888 ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL")
Reported-and-tested-by: Dean Wallace <duffydack73@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using "%s[%d]" for mod name and ID,
but, this ID portion might confusable.
For example currently, CTU ID is 0 to 7, but using 00 to 13
(= 00, 01, 02, 03, 10, 11, 12, 13) is very best matching to datasheet.
In the future, we will support BUSIFn, but it will be more complicated
numbering. To avoid future confusable code, this patch modify
rsnd_mod_name() to return understandable name.
To avoid using pointless memory, it uses static char and snprintf,
thus, rsnd_mod_name() user should use it immediately, and shouldn't keep
its pointer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ID for CTU and SSIU are confusable.
1 CTU has 4 sub nodes. This means, CTU0 has CTU01 - CTU03, CTU1 has
CTU10 - CTU13. SSIU is more confusable. Gen2 SSIU has BUSIF0-3, Gen3
SSIU has BUSIF0-7, but not for all SSIU.
In rsnd driver, each mod drivers are assuming rsnd_mod_id() returns
main device ID (In CTU case CTU0-1, SSIU case SSIU0-9), not serial
number.
This patch adds new .id/.id_sub to handling more detail ID.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each mod needs to have .get_status, but current driver is handling it
under rsnd_mod, instead of rsnd_mod_ops.
It is not any make sence. This patch moves it to rsnd_mod_ops, and
tidyup its parameter order to align to other callback functions.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
hw constraint for LEFT_J/I2S are same, but had duplicated code.
This code cleanup these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For samples sizes of 20/24/32 bit the DRR2/DXR2 registers must be used to
receive or transmit the most significant part of the 32bit sample.
We can not trick the system by using the DRR2/DXR2 register offset and use
32bit element size since these (and other McBSP) registers are 16bit ones.
We would need support for port_window in cyclic mode from the sDMA driver,
but it is not straight forward as we would need to have the sDMA frame to
cover the 32bit (DRR2+DRR1/DXR2+DXR1), but the frames must cover the ALSA
period to be able to receive periodic interrupts.
Since the 32bit samples are not working (DMA timeout), just remove it in
case we have McBSP with reg_size of 2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_desc structure can be const as it is only passed as the
second argument of devm_regulator_register and the corresponding
parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures are only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structures
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures are only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structures
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
WARN_ON() already contains an unlikely(), so it's not necessary to use
unlikely.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Randconfig testing revealed a very old bug, with gcc-8:
sound/soc/intel/atom/sst/sst_loader.c: In function 'sst_load_fw':
sound/soc/intel/atom/sst/sst_loader.c:357:5: error: 'fw' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (fw == NULL) {
^
sound/soc/intel/atom/sst/sst_loader.c:354:25: note: 'fw' was declared here
const struct firmware *fw;
We must check the return code of request_firmware() before we look at the
pointer result that may be uninitialized when the function fails.
Fixes: 9012c9544e ("ASoC: Intel: mrfld - Add DSP load and management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gcc notices that without either the ac97 bus or the pdata, we never
initialize the regmap pointer, which leads to an uninitialized variable
access:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:666:2: error: 'regmap' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Since that configuration is invalid, it's better to return an error
here. I tried to avoid adding complexity to the conditions, and turned
the #ifdef into a regular if(IS_ENABLED()) check for readability.
This in turn requires moving some header file declarations out of
an #ifdef.
The same code is used in three drivers, all of which I'm changing
the same way.
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_ops structure can be const as it is only stored in the
ops field of a snd_soc_dai_link structure and this field is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the comparison of div < 0 is always false because div is
an unsigned int. Fix this by making div an int.
Detected by CoverityScan, CID#1475309 ("Unsigned compared against 0")
Fixes: 8307b2afd3 "(ASoC: stm32: sai: set sai as mclk clock provider")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SUN50I_CODEC_ANALOG selects SND_SUNXI_ADDA_PR_REGMAP which is leftover
of renaming SND_SUNXI_ADDA_PR_REGMAP to SND_SUN8I_ADDA_PR_REGMAP. Replace
it with SND_SUN8I_ADDA_PR_REGMAP to fix possible link errors for some
configurations:
sound/soc/sunxi/sun50i-codec-analog.o: In function `sun50i_codec_analog_probe':
sun50i-codec-analog.c:(.text+0x62): undefined reference to `sun8i_adda_pr_regmap_init'
Fixes: 42371f327d ("ASoC: sunxi: Add new driver for Allwinner A64 codec's analog path controls")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4d230d1271 ("ASoC: rsnd: fixup not to call clk_get/set under
non-atomic") fixuped clock start timing. But it exchanged clock start
checker from ssi->usrcnt to ssi->rate.
Current rsnd_ssi_master_clk_start() is called from .prepare,
but some player (for example GStreamer) might calls it many times.
In such case, the checker might returns error even though it was not
error. It should check ssi->usrcnt instead of ssi->rate.
This patch fixup it. Without this patch, GStreamer can't switch
48kHz / 44.1kHz.
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates.
Here are highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAlvRbLkOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9FMg//eGuq13WyoNn4OrgncGdxP4U+Dd3qXj7h6wmo
af8ZebRSZht5jswJz5TEmYM5zR8jfKfDCN6bDKIV99Ondp9bN1vEqxBa2mUx9T/C
mhY17dPJX0Fwdk951TkAANfOvIqECjqWj9qMI4QdigfVqVXaIxdPSnA4tKDtq6++
Ocr4+GtC01Nmd/jWzpC4fDh9k+mwTAG0VZjeLFCjsv61U9DKbic+UcRni7YTvRGg
pUXWNNUxIa6FMYEpsHClBJkCCUi4+ZT9nQe7Dy/W4lMq0uVBrPBqDYQJKDdjwf4p
VEptmlhEpMcY/bG1yW7l5YOHgYs8Cx5YYygBag+3YCE6a6KItuxNp9UbgxGqZ7GD
Svh4vPn8n4+UZfMbS04IlYvJP8bTiIfHRLkUBSHgC2egco0TjDEZiH71ucxFOq9q
3cVKlSfLvcSMCAnUiDP18EfBq6ayGJmzJsFzU1RZLW/r+RcuMzPuwAbCuC83mlI4
bobNLXCyEArJlvQyrAAIXrX/j4GhFzheL26hXQ96tQ9Y/nNX9tE/cL8bWtm45i4s
+EuPnWosfZbo5JtPASosEQhilVrrOK/VmqAA6xHURKxspdqwIVyOvAa6kPLRJx8T
LvczeX9pK3PwvZhDU+eg+HpcPNSWH8BtPvShutsNd0lp9UGBFeBUB5gc4s0iYqLq
rMnbzwg=
=3LrT
-----END PGP SIGNATURE-----
Merge tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been little changes in ALSA core stuff, but ASoC core still
kept rolling for the continued restructuring. The rest are lots of
small driver-specific changes and some minor API updates. Here are
highlights:
General:
- Appropriate fall-through annotations everywhere
- Some code cleanup in memalloc code, handling non-cacahed pages more
commonly in the helper
- Deployment of SNDRV_PCM_INFO_SYNC_APPLPTR flag consistently
Drivers:
- More HD-audio CA0132 codec improvement for supporting other Creative
boards
- Plumbing legacy HD-audio codecs as ASoC BE on Intel SST; this will
give move support of existing HD-audio devices with DSP
- A few device-specific HD-audio quirks as usual
- New quirk for RME CC devices and correction for B&W PX for USB-audio
- FireWire: code refactoring including devres usages
ASoC Core:
- Continued componentization works; it's almost done!
- A bunch of new for_each_foo macros
- Cleanups and fixes in DAPM code
ASoC Drivers:
- MCLK support for several different devices, including CS42L51, STM32
SAI, and MAX98373
- Support for Allwinner A64 CODEC analog, Intel boards with DA7219 and
MAX98927, Meson AXG PDM inputs, Nuvoton NAU8822, Renesas R8A7744 and
TI PCM3060"
* tag 'sound-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (299 commits)
ASoC: stm32: sai: fix master clock naming
ASoC: stm32: add clock dependency for sai
ALSA: hda/ca0132 - Actually fix microphone issue
ASoC: sun4i-i2s: move code from startup/shutdown hooks into pm_runtime hooks
ASoC: wm2000: Remove wm2000_read helper function
ASoC: cs42l51: fix mclk support
ASoC: wm_adsp: Log addresses as 8 digits in wm_adsp_buffer_populate
ASoC: wm_adsp: Rename memory fields in wm_adsp_buffer
ASoC: cs42l51: add mclk support
ASoC: stm32: sai: set sai as mclk clock provider
ASoC: dt-bindings: add mclk support to cs42l51
ASoC: dt-bindings: add mclk provider support to stm32 sai
ASoC: soc-core: fix trivial checkpatch issues
ASoC: dapm: Add support for hw_free on CODEC to CODEC links
ASoC: Intel: kbl_da7219_max98927: minor white space clean up
ALSA: i2c/cs8427: Fix int to char conversion
ALSA: doc: Brush up the old writing-an-alsa-driver
ASoC: rsnd: tidyup SSICR::SWSP for TDM
ASoC: rsnd: enable TDM settings for SSI parent
ASoC: pcm3168a: add hw constraint for capture channel
...
sound/soc/stm/stm32_sai_sub.c:393:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
CC: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull perf updates from Ingo Molnar:
"The main updates in this cycle were:
- Lots of perf tooling changes too voluminous to list (big perf trace
and perf stat improvements, lots of libtraceevent reorganization,
etc.), so I'll list the authors and refer to the changelog for
details:
Benjamin Peterson, Jérémie Galarneau, Kim Phillips, Peter
Zijlstra, Ravi Bangoria, Sangwon Hong, Sean V Kelley, Steven
Rostedt, Thomas Gleixner, Ding Xiang, Eduardo Habkost, Thomas
Richter, Andi Kleen, Sanskriti Sharma, Adrian Hunter, Tzvetomir
Stoyanov, Arnaldo Carvalho de Melo, Jiri Olsa.
... with the bulk of the changes written by Jiri Olsa, Tzvetomir
Stoyanov and Arnaldo Carvalho de Melo.
- Continued intel_rdt work with a focus on playing well with perf
events. This also imported some non-perf RDT work due to
dependencies. (Reinette Chatre)
- Implement counter freezing for Arch Perfmon v4 (Skylake and newer).
This allows to speed up the PMI handler by avoiding unnecessary MSR
writes and make it more accurate. (Andi Kleen)
- kprobes cleanups and simplification (Masami Hiramatsu)
- Intel Goldmont PMU updates (Kan Liang)
- ... plus misc other fixes and updates"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (155 commits)
kprobes/x86: Use preempt_enable() in optimized_callback()
x86/intel_rdt: Prevent pseudo-locking from using stale pointers
kprobes, x86/ptrace.h: Make regs_get_kernel_stack_nth() not fault on bad stack
perf/x86/intel: Export mem events only if there's PEBS support
x86/cpu: Drop pointless static qualifier in punit_dev_state_show()
x86/intel_rdt: Fix initial allocation to consider CDP
x86/intel_rdt: CBM overlap should also check for overlap with CDP peer
x86/intel_rdt: Introduce utility to obtain CDP peer
tools lib traceevent, perf tools: Move struct tep_handler definition in a local header file
tools lib traceevent: Separate out tep_strerror() for strerror_r() issues
perf python: More portable way to make CFLAGS work with clang
perf python: Make clang_has_option() work on Python 3
perf tools: Free temporary 'sys' string in read_event_files()
perf tools: Avoid double free in read_event_file()
perf tools: Free 'printk' string in parse_ftrace_printk()
perf tools: Cleanup trace-event-info 'tdata' leak
perf strbuf: Match va_{add,copy} with va_end
perf test: S390 does not support watchpoints in test 22
perf auxtrace: Include missing asm/bitsperlong.h to get BITS_PER_LONG
tools include: Adopt linux/bits.h
...
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
Fix warning issued by strncat when bound equals to source length.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 8307b2afd3 ("ASoC: stm32: sai: set sai as mclk clock provider")
Add COMMON_CLK dependency for STM32 SAI,
as it is required by clock provider.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
startup() and shutdown() hooks are called for both substreams,
so stopping either substream when another is running breaks the
latter.
E.g. playback breaks if capture is stopped when playback is running.
Move code from startup() and shutdown() to resume() and suspend()
hooks respectively to fix this issue
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The return type "unsigned int" was used by the wm2000_read()
function despite of the aspect that it will eventually return
a negative error code.
The resulting function doesn't add much to the code, so replace
wm2000_read with regmap_read.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCLK clock is made optional for cs42l51 codec.
However, ASoC DAPM clock supply widget, expects the clock to be defined
unconditionally.
Register MCLK DAPM conditionally in codec driver,
depending on clock presence in DT.
Fixes: 5e8d63a726 ("ASoC: cs42l51: add mclk support")
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Increase the address value width in the debug log from 4 digits to
8 digits to allow for DSP cores with larger memory address ranges.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm_adsp_buffer struct is the control header of a circular
buffer used to transfer data from the firmware over the
control interface to an ALSA compressed stream.
The original names of the fields pointing to the data buffer
were based on ADSP2V2 memory layout where they correspond to
{XM, XM, YM}. But this circular buffer could be used on other
types of DSP core that have different memory region types.
Also the names and description of the size fields were not
very clear. The field names and descriptions have been changed
to be generic and not imply any particular memory types.
This patch updates the wm_adsp driver to the new field names.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add MCLK dapm to allow configuration of cirrus CS42l51
codec as a master clock consumer.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add master clock generation support in STM32 SAI.
The master clock provided by SAI can be used to feed a codec.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a few trivial aka cosmetic only checkpatch issues like long lines,
wrong indentations, spurious blanks and newlines, missing newlines,
multi-line comments etc.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, on power down for a CODEC to CODEC DAI link we only call
digital_mute and shutdown. Provide a little more flexibility for drivers
by adding a call to hw_free as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car datasheet is indicating that WS output settings of SSICR::SWSP
is inverted on TDM mode from non TDM mode settings.
But, it is meaning that TDM should use 0 here.
Without this patch, sound input/output 1ch will be 2ch, 2ch will be 3ch
..., be jumbled on I2S + TDM settings. This patch fixup it.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SSIs are sharing each pins (= WS/CLK pin for playback/capture).
Then, SSI parent needs control WS/CLK setting for SSI slave.
In such case, SSI parent needs TDM settings if SSI slave is working as
TDM mode. But it is not cared in current driver.
It can't capture TDM sound without this patch if SSIs were pin sharing.
This patch is tested on R-Car H3 ulcb-kf board, SSI3/4 with TDM sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
commit 594680ea4a ("ASoC: pcm3168a: add hw constraint for channel")
commit 3809688980 ("ASoC: pcm3168a: add HW constraint for non
RIGHT_J") added channel constraint for it, but, it was only for playback.
This patch adds constraint for capture.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STA32x chips feature an XTI clock input that needs to be stable before
the reset signal is released. Therefore, the chip driver needs to get a
handle to the clock. Instead of relying on other parts of the system to
enable the clock, let the codec driver grab a handle itself.
In order to keep existing boards working, clock support is made optional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to the following:
commit 4321723648 ("ASoC: tegra_alc5632: fix device_node refcounting")
commit 7c5dfd5496 ("ASoC: tegra: fix device_node refcounting")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner A64 uses the same digital codec part as in A33, so we need
to build this driver on ARM64 as well.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The internal codec on A64 is split into 2 parts. The analog path controls
are routed through an embedded custom register bus accessed through
the PRCM block.
Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be reused by sun50i-codec-analog later.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BCLK / LRCK ratio should be sample size * channels, but it was
hardcoded to 32 (0x1 is 32 as per A33 and A64 datasheets).
Calculate it basing on sample size and number of channels.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S block used for the audio codec in the A64 differs from other 3
I2S modules in A64 and isn't compatible with H3. But it is very similar
to what is found in A10(sun4i). However, its TX FIFO is
located at a different address.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds da7219_max98927 machine driver entry into
machine table
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Kabylake I2S machine driver with:
DA7219 audio codec(SSP1) and MAXIM98927(SSP0) speaker amplifier.
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some 3 pole connectors report impedance greater than threshold of
1000Ohm. Thus, da7219 reports them as LINEOUT.
Adding the SND_JACK_LINEOUT type so that we don't fail to detect
any 3 pole jack type.
Also, changing
SND_JACK_HEADPHONE | SND_JACK_MICROPHONE -> SND_JACK_HEADSET
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm3168a is supporting TDM on I2S/Left_J, but there is no
settings for it. This patch add it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
This patch adds channel constraint for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RIGHT_J only can handle 16bit data bits.
Current driver just errored if user requests non RIGHT_J
+ 16bit combination. But it is not useful for user.
This patch adds HW constraint for it, and avoid
error on such situation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ESD watchdog code in sta32x_watchdog() dereferences the pointer
which is never assigned.
This is a regression from a1be4cead9 ("ASoC: sta32x: Convert to direct
regmap API usage.") which went unnoticed since nobody seems to use that ESD
workaround.
Fixes: a1be4cead9 ("ASoC: sta32x: Convert to direct regmap API usage.")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Current audio-graph-card is supporting mclk-fs on CPU node
side only. But having Codec node also is good idea.
It will be just ignored if not defined.
"rcpu_ep" is same as "cpu_ep", This patch tidyup it, too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit fb2815f44a ("ASoC: rsnd: add support for 16/24 bit slot widths")
added TDM width check, and return error if it was not 16/24/32 bit.
But it is too strict. This patch uses 32bit same as default.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
max98988 only builds with I2C support enabled, otherwise we get a build error:
sound/soc/codecs/max98088.c:1789:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(max98088_i2c_driver);
^~~~~~~~~~~~~~~~~
sound/soc/codecs/max98088.c:1789:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
sound/soc/codecs/max98088.c:1789:1: error: parameter names (without types) in function declaration [-Werror]
sound/soc/codecs/max98088.c:1780:26: error: 'max98088_i2c_driver' defined but not used [-Werror=unused-variable]
Fixes: 24ae67c582 ("ASoC: max98988: make it selectable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver will build only if SND_SOC_ALL_CODECS is set.
Adding a Kconfig menu description to build the driver standalone.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Cc: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Tushar Behera <trblinux@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[m.felsch@pengutronix.de: move mclk request to i2c_probe]
[m.felsch@pengutronix.de: make use of snd_soc_component_get_bias_level()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lookup regulators for Vdd and Vdda during probe, and enable them when the
component is linked.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
gcc can't understand the mixed texts, unfortunately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotation in Intel SST
skylake driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, add the "fall through" annotations in rt274 driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation.
Unfortunately gcc doesn't understand the mixed comment lines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As a preparatory patch for the upcoming -Wimplicit-fallthrough
compiler checks, replace with the standard "fall through" annotation
at the right place. It has to be put right before the next label.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver already has support for setting the FDRB bit in the CONFA
register through platform data, but there was no property to set it
in the device-tree bindings.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a "extclk" clock is given, enable and disable it when appropriate.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The q6asm_audio_client_alloc() doesn't return NULL, it returns error
pointers.
Fixes: 2a9e92d371 ("ASoC: qdsp6: q6asm: Add q6asm dai driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_tplg_get_token() misses a break in the big switch() block for
SKL_TKN_U8_CORE_ID entry.
Spotted nicely by -Wimplicit-fallthrough compiler option.
Fixes: 6277e83292 ("ASoC: Intel: Skylake: Parse vendor tokens to build module data")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Going primarily by:
https://en.wikipedia.org/wiki/List_of_Intel_Atom_microprocessors
with additional information gleaned from other related pages; notably:
- Bonnell shrink was called Saltwell
- Moorefield is the Merriefield refresh which makes it Airmont
The general naming scheme is: FAM6_ATOM_UARCH_SOCTYPE
for i in `git grep -l FAM6_ATOM` ; do
sed -i -e 's/ATOM_PINEVIEW/ATOM_BONNELL/g' \
-e 's/ATOM_LINCROFT/ATOM_BONNELL_MID/' \
-e 's/ATOM_PENWELL/ATOM_SALTWELL_MID/g' \
-e 's/ATOM_CLOVERVIEW/ATOM_SALTWELL_TABLET/g' \
-e 's/ATOM_CEDARVIEW/ATOM_SALTWELL/g' \
-e 's/ATOM_SILVERMONT1/ATOM_SILVERMONT/g' \
-e 's/ATOM_SILVERMONT2/ATOM_SILVERMONT_X/g' \
-e 's/ATOM_MERRIFIELD/ATOM_SILVERMONT_MID/g' \
-e 's/ATOM_MOOREFIELD/ATOM_AIRMONT_MID/g' \
-e 's/ATOM_DENVERTON/ATOM_GOLDMONT_X/g' \
-e 's/ATOM_GEMINI_LAKE/ATOM_GOLDMONT_PLUS/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: dave.hansen@linux.intel.com
Cc: len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove duplicated includes linux/of_platform.h
and linux/wait.h
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'ret' variable is now only used in an #ifdef, and causes a
warning if it is declared outside of that block:
sound/soc/codecs/wm9712.c: In function 'wm9712_soc_probe':
sound/soc/codecs/wm9712.c:641:6: error: unused variable 'ret' [-Werror=unused-variable]
Fixes: 2ed1a8e0ce ("ASoC: wm9712: add ac97 new bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Selecting AC97_BUS_NEW from SND_PXA2XX_SOC_AC97 leads to a Kconfig
warning if any other driver selects AC97_BUS:
WARNING: unmet direct dependencies detected for AC97_BUS_COMPAT
Depends on [n]: SOUND [=y] && !UML && SND [=y] && AC97_BUS_NEW [=y] && !AC97_BUS [=y]
Selected by [y]:
- SND_SOC_WM9713 [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y] && AC97_BUS_NEW [=y]
I don't know if that combination is supposed to work.
Assuming it is not, this adds a dependency on all users
for PXA to avoids the combination.
Fixes: 1c8bc7b3de ("ASoC: pxa: switch to new ac97 bus support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The symbols 'dummy_dma_ops' is declared with different data types by
sound/soc/soc-utils.c and arch/arm64/include/asm/dma-mapping.h. This
leads to conflicts when soc-utils.c (indirectly) includes dma-mapping.h:
sound/soc/soc-utils.c:282:33: error: conflicting types for 'dummy_dma_ops'
static const struct snd_pcm_ops dummy_dma_ops = {
^
...
arch/arm64/include/asm/dma-mapping.h:27:33: note: previous declaration of 'dummy_dma_ops' was here
extern const struct dma_map_ops dummy_dma_ops;
^
Rename the symbol in soc-utils.c to 'snd_dummy_dma_ops' to avoid the
conflict.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAX98088 is an older version of the MAX98089 device.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[m.felsch@pengutronix.de: add CONFIG_OF compile switch]
[m.felsch@pengutronix.de: adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4265 driver is missing a microphone preamp enable.
This patch enables/disables the microphone preamp when mic
selection is made using the kcontrol.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_component_dais() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_component() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prepare <-> Cleanup functions pair has balanced calls.
But in case of suspend mode no call to rsnd_soc_dai_shutdown()
function, so cleanup isn't called. OTOH during resume mode
function rsnd_soc_dai_prepare() is called, but calling
rsnd_ssi_prepare() is skipped (rsnd_status_update() returns zero,
bacause was not cleanup before).
We need to call rsnd_ssi_prepare(), because it enables SSI clocks
by calling rsnd_ssi_master_clk_start().
This patch allows to call prepare/cleanup functions always.
Signed-off-by: Dmytro Prokopchuk <dmytro.prokopchuk@globallogic.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
[kuninori: adjusted to upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We include wait.h twice in q6adm.c. it is unnecessary. hence remove
it. Further, order the include files as alphabet.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 7fe072b4df ("ASoC: add for_each_card_prelinks() macro")
added new for_each_card_prelinks() macro, but it had typo.
This patch fixup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch removes the boost volume in the beginning of playback while the
DAC volume set to lower.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_dpcm_be() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_dpcm_fe() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_comp_order() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_card_components() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_card_rtds() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_card_links() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be more readable code, this patch adds
new for_each_card_prelinks() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 0b7990e389 ("ASoC: add for_each_rtd_codec_dai() macro")
added for_each_rtd_codec_dai_reverse(). but _rollback() is better
naming than _reverse(). This patch rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 0b7990e389 ("ASoC: add for_each_rtd_codec_dai() macro")
added for_each_rtd_codec_dai(), but it didn't convert few loop
which is not using "rtd". This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This SPI driver does not use the legacy GPIO header so
just delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Minor code changes are:
- improve the readability in patch list
- add i2c remove function
- regmap_register_patch changes to regmap_multi_reg_write
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
alsa_conformance_test -C hw:0,4 -p 1024 --debug
would sometime show:
TIME_DIFF(s) HW_LEVEL READ RATE
0.000095970 1024 1024 10670001.041992
0.042609555 1024 2048 24032.168372
0.021330364 1024 3072 48006.681930
0.021339559 1024 4096 47985.996337
The issue is that in dma pointer function we can have stale value
of the register for current descriptor of channel.
The register retains the number of the last descriptor that
was transferred.
Fix ensures that we report position, 0, till the one period worth of
data is transferred. After one period of data, in handler of period
completion interrupt we update the config and correct value of descriptor
starts reflecting.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixed the boost volume at the begining of playback
while DAC volume set to lower level.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADC/DAC path should open while calibration process.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removed Headphone Playback Volume control.
Due to codec settings, we don't want the user to change HP analog gain.
The user could use DAC1 Playback Volume control to
change playback volume.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We change the settings while HP power-up for better performance.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
module.h already contained moduleparam.h, so it is safe to remove
the redundant include.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The value of period_bytes will get the zero before the hw_params() is not
run completely. Move the function snd_pcm_lib_period_bytes() to copy work,
and make sure that is not zero.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To find (CPU/)Codec/Platform, we need to find component first
(= on CPU/Codec/Platform), and find DAI from it (= CPU/Codec).
These are similar operation but difficult to be simple,
and has many duplicate code to finding component.
This patch adds new snd_soc_is_matching_component(),
and reduce duplicate codes.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now "platform" is controlled by snd_soc_dai_link_component,
thus its "name" can be initialized in snd_soc_init_platform(),
instead of soc_bind_dai_link() local.
This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the usual set of small fixes scatterd around various drivers,
plus one fix for DAPM and a UAPI build fix. There's not a huge amount
that stands out here relative to anything else.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluf2AQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BojB/9ZpiRgSSjKTFSmGgu3OFI7Nvj63ruB
hxOnwOc8Bea8tZtpzgEcx/aLZ1sbWVT4uRUYZv0Tf6UJtuOQagbJDEUkUdRitKtX
1khSMyKFlAa7cIbv19ZOMCN0pjcs7hlHCPryT8AyCWCWN8yPdlUsDqWfyfUoq56r
qpdu/OQ4E9VvS8OcX1gPjcop3gE/fYEoU+mbUpr0KYUXaroEzJm85tOqpGYk4+XW
GCNUR19vNRJr5G6ANqIx96JOlgF5nRZu7aOfvLceiWH5BgPdW3iNRAJkPmKCIHwb
a1+X21eCC7Ec2/7bQmR5Aoxz1yqzhngrevSFNLrqXFZmMmNrEfkfdCrJ
=gVzO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.19
This is the usual set of small fixes scatterd around various drivers,
plus one fix for DAPM and a UAPI build fix. There's not a huge amount
that stands out here relative to anything else.
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Internally, skl_init_chip() calls snd_hdac_bus_init_chip() which
1) sets bus->chip_init to prevent multiple entrances before device
is stopped; 2) enables interrupt.
We shouldn't use it for the purpose of resetting device only because
1) when we really want to initialize device, we won't be able to do
so; 2) we are ready to handle interrupt yet, and kernel crashes when
interrupt comes in.
Rename azx_reset() to snd_hdac_bus_reset_link(), and use it to reset
device properly.
Fixes: 60767abcea ("ASoC: Intel: Skylake: Reset the controller in probe")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 12eeeb4f47.
The patch doesn't fix accessing memory with null pointer in
skl_interrupt().
There are two problems: 1) skl_init_chip() is called twice, before
and after dma buffer is allocate. The first call sets bus->chip_init
which prevents the second from initializing bus->corb.buf and
rirb.buf from bus->rb.area. 2) snd_hdac_bus_init_chip() enables
interrupt before snd_hdac_bus_init_cmd_io() initializing dma buffers.
There is a small window which skl_interrupt() can be called if irq
has been acquired. If so, it crashes when using null dma buffer
pointers.
Will fix the problems in the following patches. Also attaching the
crash for future reference.
[ 16.949148] general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI
<snipped>
[ 16.950903] Call Trace:
[ 16.950906] <IRQ>
[ 16.950918] skl_interrupt+0x19e/0x2d6 [snd_soc_skl]
[ 16.950926] ? dma_supported+0xb5/0xb5 [snd_soc_skl]
[ 16.950933] __handle_irq_event_percpu+0x27a/0x6c8
[ 16.950937] ? __irq_wake_thread+0x1d1/0x1d1
[ 16.950942] ? __do_softirq+0x57a/0x69e
[ 16.950944] handle_irq_event_percpu+0x95/0x1ba
[ 16.950948] ? _raw_spin_unlock+0x65/0xdc
[ 16.950951] ? __handle_irq_event_percpu+0x6c8/0x6c8
[ 16.950953] ? _raw_spin_unlock+0x65/0xdc
[ 16.950957] ? time_cpufreq_notifier+0x483/0x483
[ 16.950959] handle_irq_event+0x89/0x123
[ 16.950962] handle_fasteoi_irq+0x16f/0x425
[ 16.950965] handle_irq+0x1fe/0x28e
[ 16.950969] do_IRQ+0x6e/0x12e
[ 16.950972] common_interrupt+0x7a/0x7a
[ 16.950974] </IRQ>
<snipped>
[ 16.951031] RIP: snd_hdac_bus_update_rirb+0x19b/0x4cf [snd_hda_core] RSP: ffff88015c807c08
[ 16.951036] ---[ end trace 58bf9ece1775bc92 ]---
Fixes: 2eeeb4f4733b ("ASoC: Intel: Skylake: Acquire irq after RIRB allocation")
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is strange if it has "dai" but doesn't have "dai->driver".
And more over "dai->driver->xxx" is used everywhere without
"dai->driver" pointer NULL checking.
It got Oops already if "dai->driver" was NULL.
Let's remove un-needed "dai->driver" NULL check.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current behaviour of ASoC core w.r.t to component removal is that it
unregisters dependent sound card totally. There is no support to
rebind the card if the component comes back.
Typical use case is DSP restart or kernel modules itself.
With this patch, core now maintains list of cards that are unbind due to
any of its depended components are removed and card not unregistered yet.
This list is cleared when the card is rebind successfully or when the
card is unregistered from machine driver.
This list of unbind cards are tried to bind once again after every new
component is successfully added, giving a fair chance for card bind
to be successful.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
platform_driver_register will set the .owner field. So it is safe
to remove the redundant assignment.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_INFO_INTERLEAVED into PCM hardware info.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC is counting card->dai_link_list user,
but no-one is using it.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Nested code is not readable.
This patch avoid it on soc_remove_dai().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5668_i2c_remove() is empty, and no longer needed.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In functions snd_soc_get_volsw_sx() or snd_soc_put_volsw_sx(),
if the result of (min + max) is negative, then fls() returns
signed integer with value as 32. This leads to signed integer
overflow as complete operation is considered as signed integer.
UBSAN: Undefined behaviour in sound/soc/soc-ops.c:382:50
signed integer overflow:
-2147483648 - 1 cannot be represented in type 'int'
Call trace:
[<ffffff852f746fe4>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffff852f746fe4>] dump_stack+0xec/0x158 lib/dump_stack.c:51
[<ffffff852f7b5f3c>] ubsan_epilogue+0x18/0x50 lib/ubsan.c:164
[<ffffff852f7b6840>] handle_overflow+0xf8/0x130 lib/ubsan.c:195
[<ffffff852f7b68f0>] __ubsan_handle_sub_overflow+0x34/0x44 lib/ubsan.c:211
[<ffffff85307971a0>] snd_soc_get_volsw_sx+0x1a8/0x1f8 sound/soc/soc-ops.c:382
Typecast the operation to unsigned int to fix the issue.
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the new ac97 bus support in sound/ac97 instead of the legacy
snd_ac97 one.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
If capture and playback are started on different channel (I2S/BT)
there is a possibilty that channel information passed from machine driver
is overwritten before the configuration is done in dma driver.
Example:
113.597588: cz_max_startup: ---playback sets BT channel
113.597694: cz_dmic1_startup: ---capture sets I2S channel
113.597979: acp_dma_hw_params: ---configures capture for I2S channel
113.598114: acp_dma_hw_params: ---configures playback for I2S channel
This is fixed by having 2 separate instance for playback and capture.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMTLR bit is in the CS4265_SPDIF_CTL2 register at address 0x12 bit 0
and not at address 0x0 bit 1. Fix this.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
snd_soc_dapm_new_dai may return an error pointer and currently this
isn't checked for in dapm_connect_dai_link_widgets. Add code to check
the return value and not add routes in that case.
Fixes: 778ff5bb86 ("ASoC: dapm: Move connection of CODEC to CODEC DAIs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kmemdup has implemented the function that kzalloc() + memcpy() will
do. and we prefer to kmemdup rather than the open coded implementation.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kmemdup has implemented the function that kzalloc() + memcpy() will
do. and we prefer to use the kmemdup rather than the open coded implementation.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we have devm_snd_soc_register_component().
Let's use it instead of snd_soc_register_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW register descriptions says:
"DMA Channel Reset...Software must confirm that this bit is
cleared before reprogramming any of the channel configuration registers."
There could be cases where dma stop errored out leaving dma channel
in reset state. We need to ensure that before the start of another dma,
channel is out of the reset state.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch complains that if both "psubstream" and "csubstream" are NULL
then "ret" is uninitialized. That probably can't happen, but it's
cleaner to just return zero anyway so let's do that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch complains that these variables could be uninitialized. The first
one in snd_soc_dai_link_event() is probably a false positive, because
probably we know the lists are not empty. I would normally ignore the
warning, but GCC complains here as well so I just silenced the warning.
The "ret" in snd_soc_dapm_new_dai() does need to be initialized or it
leads to a bogus dereference in the caller.
Fixes: 3bbf5d34fd ("ASoC: dapm: Move error handling to snd_soc_dapm_new_control_unlocked")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit ca917f9fe1 added use of usleep_range() but not
the corresponding "include <linux/delay.h>". The result is
with Chrome OS won't build because warnings are forced
to be errors:
mnt/host/source/src/third_party/kernel/v4.4/sound/soc/codecs/max98373.c:734:2: error: implicit declaration of function 'usleep_range' [-Werror,-Wimplicit-function-declaration]
usleep_range(10000, 11000);
^
Including delay.h "fixes" this.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Playback of 44.1Khz contents with HDMI plugged returns
"Invalid pipe config" because HDMI paths in the FW
topology are configured to operate at 48Khz.
This patch filters out sampling rates not supported
at hdac_hdmi_create_dais() to let user space SRC
to do the converting.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 4a75aae17b ("ASoC: dapm: Add support for multi-CODEC
CODEC to CODEC links") adds loops that iterate over multiple
CODECs in snd_soc_dai_link_event. This also introduced a compiler
warning for a potentially uninitialised variable in the case
no CODECs are present. This should never be the case as the
DAI link must by definition contain at least 1 CODEC however
probably best to avoid the compiler warning by initialising ret
to zero.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver sometimes want to know which address is used when debugging.
But it will indicate "(____ptrval____)" if it used "%p" on dev_dbg().
Let's use "%pa" or "%px" for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver will fallback to PIO mode if it can't get DMA
handler. But, DMA might return -EPROBE_DEFER when probe timing.
This driver always fallback to PIO mode especially from
commit ac6bbf0cdf ("iommu: Remove IOMMU_OF_DECLARE") because
of this reason.
The DMA driver will be probed later, but sound driver might be
probed as PIO mode in such case. This patch fixup this issue.
Then, -EPROBE_DEFER is not error. Thus, let's don't indicate error
message in such case.
And it needs to call rsnd_adg_remove() individually if probe failed,
because it registers clk which should be unregister.
Maybe PIO fallback feature itself is not needed,
but let's keep it so far.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG has buffer over flow bug if DT has more than 3 clock-frequency.
This patch fixup this issue, and uses first 2 values.
clock-frequency = <x y>; /* this is OK */
clock-frequency = <x y z>; /* this is NG */
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 8c9d750333 ("ASoC: rsnd: ssiu: Support BUSIF
other than BUSIF0") added new SSIU registers.
But it is using white-space for it.
This patch fixup it to use tab.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The !port check is redundant as it being performed in the following
check. Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Larger CODECs may contain many several hundred widgets and which set of
parameters is selected only needs to be recorded on a per DAI basis. As
such move the selected CODEC to CODEC link params to be stored in the
runtime rather than the DAPM widget, to save some memory.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently multi-CODEC is not supported on CODEC to CODEC links.
There are common applications where this would be useful, such
as connecting two mono amplifiers to an audio CODEC. Adding
support simply requires an update of snd_soc_dai_link_event
to loop over the attached CODEC DAIs.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, snd_soc_dapm_connect_dai_link_widgets connects up the routes
representing normal DAIs, however CODEC to CODEC links are hooked up
through separate infrastructure in soc_link_dai_widgets. Improve the
consistency of the code by using snd_soc_dapm_connect_dai_link for both
types of DAIs.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the function snd_soc_dapm_new_control to be next to
snd_soc_dapm_new_controls and add some kernel doc for it.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DAPM has a lot of similar code to handle errors from
snd_soc_dapm_new_control_unlocked, and much of this code does
not really accurately reflect what the function returns.
Firstly, most places will check for a return value of
-EPROBE_DEFER and silence any error messages in that case. The
one notable exception here being dapm_kcontrol_data_alloc
which does currently print any error messages in the case
of snd_soc_dapm_new_control_unlocked returning NULL or an
error. Additionally the error prints being silenced in these
case are redundant as snd_soc_dapm_new_control_unlocked can
only return -EPROBE_DEFER or NULL when failing.
Secondly, most places will treat a return value of NULL as
an -ENOMEM. This is not correct either since any error except
EPROBE_DEFER will cause a return value of NULL from
snd_soc_dapm_new_control_unlocked.
Centralise this handling and the error messages within
snd_soc_dapm_new_control_unlocked and update the callers
to simply check IS_ERR and return. Note that this update is
slightly simpler in the case of dapm_kcontrol_data_alloc where
that is fairly close to the handling that was already in place.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC snd_soc_pcm_runtime has snd_soc_dai array for codec_dai.
To be more readable code, this patch adds
new for_each_rtd_codec_dai() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC snd_soc_dai_link has snd_soc_dai_link_component array
for codecs.
To be more readable code, this patch adds
new for_each_link_codecs() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to short circuit detection, when the ADC/DAC is saturated and
overflows poor audio quality can result and should be reported to the
user. This device support Automatic Dynamic Range Compression (DRC)
to reduce this but it is not enabled currently in this driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vijendar Mukunda