Due to obviously missing braces, EESR.TABT (transmit abort) interrupt may be
reported even if it hasn't happened, just when EESR.TWB (transmit descriptor
write-back) interrupt happens. Luckily (?), EESR.TWB is disabled by the driver
via the TRIMD register and all the interrupt masks, so that transmit abort is
never actually logged...
Put the braces where they should be and fix the incoherent comment, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EESR.RFE (receive FIFO overflow) interrupt is enabled by the driver on all SoCs
and sh_eth_error() handles it but it's not present in any initializer/assignment
of the 'eesr_err_check' field of 'struct sh_eth_cpu_data'. This leads to that
interrupt not being handled and cleared, and finally to disabling IRQ and the
driver being non-functional.
Modify DEFAULT_EESR_ERR_CHECK macro and all explicit initializers of the above
mentioned field to contain the EESR.RFE bit. Remove useless backslashes from the
initializers, while at it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that the driver increments the "RX length error"
on every buffer in sh_eth_rx() if the R8A7740.
This patch also adds a description about the Receive Frame Status bits.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first loop in sh_eth_check_reset() runs to its end, 'cnt' is 0, so the
following check for 'cnt < 0' fails to catch the timeout. Fix the condition in
this check, so that the timeout is actually reported.
While at it, fix the grammar in the failure message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Renesas R-Car based development boards, although a MAC address is printed on
all the Ethernet port labels, U-Boot doesn't write a valid MAC address to the
Ether MAHR/MALR registers (there's no storage provided for the Ether MAC address
either), so we have to resort to using a random MAC address...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for another ARM member of the R-Car family, R-Car M1A, also known as
R8A77781 -- it will share the code with previously added R8A77790.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d0418bb712 (net: sh_eth: Add eth support
for R8A7779 device) was a failed attempt to add support for one of members of
the R-Car SoC family. That's for three reasons: it treated R8A7779 the same
as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask
in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in
R-Car Ether), and it didn't add a new register offset array despite the closest
SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether
registers have, and also some of the registers in this old mapping don't exist
on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not
adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724
related section to its pristine state...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver's header file contains initialized register offset tables which (as
any data definitions), of course, have no business being there. Move them to
the driver's body, somewhat beautifying the initializers, while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d5e07e6921 (sh_eth: use managed device API)
has caused this warning (due to my overlook):
drivers/net/ethernet/renesas/sh_eth.c: In function `sh_eth_drv_remove':
drivers/net/ethernet/renesas/sh_eth.c:2482:25: warning: unused variable `mdp'
[-Wunused-variable]
Kill the darn variable now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the driver to the managed device API by replacing ioremap() calls with
devm_ioremap_resource() (that will also result in calling request_mem_region()
which the driver forgot to do until now) and k[mz]alloc() with devm_kzalloc() --
this permits to simplify driver's probe()/remove() method cleanup. We can now
remove the ioremap() error messages since the error messages are printed by
devm_ioremap_resource() itself. We can also remove the 'bitbang' field from
'struct sh_eth_private' as we don't need it anymore in order to free the memory
behind it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_drv_probe() does cast from 'void *' when assigning to the 'pd' variable
which is automatic anyway. Turn the assignment into initializer, while removing
the cast...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mdio_init() uses the bare numbers instead of the PHY interface bits, despite
these are declared in sh_eth.h as 'enum PIR_BIT'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
One must check the result of ioremap() -- in this case it prevents potential
kernel oops when initializing TSU registers further on...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mdio_init() allocates pointer to 'struct bb_info' but only stores it locally,
so that sh_mdio_release() can't free it on driver unload. Add the pointer to
'struct bb_info' to 'struct sh_eth_private', so that sh_mdio_init() can save
'bitbang' variable for sh_mdio_release() to be able to free it later...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sh_eth_drv_probe() return 0 for success and negative value
for most of its internal tests failures. There is one exception
that is error case going to out_release:. For this error case, the
function abort its success execution path, but returns non negative
value, making it difficult for a caller function to notice the error.
This patch fixes the error case that do not return negative value.
This was found by Coccinelle, but the code change was made by hand.
This patch is not robot generated.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports the ethtool's set_ringparam() and get_ringparam().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After freeing the buffer, the driver should change the value of
the pointer to NULL.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary members in sh_th_private.
This patch also removes unnecessary definitions in sh_eth.h
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_timer() called mod_timer() for itself. So, this patch
removes the function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sh_eth_reset function resets chip, but this performs nothing when failed.
This changes sh_eth_reset return an error, when this failed in reset.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet IP of SH7734 and R8A7740 has selecting MII register.
The user needs to change a value according to MII to be used.
This adds the function to change the value of this register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit couldn't work if the RMCR is not set to 1.
"net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens"
commit id 79fba9f517
If RMCR is not set, the controller will clear the EDRRR after it received
a frame. In this case, the driver doesn't need to fix the value of
cur_rx/dirty_rx. The driver only needs it when the controll detects
receive descriptors are empty.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Receive Descriptor Empty happens, rxdesc pointer of the driver
and actual next descriptor of the controller may be mismatch.
This patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R8A7740 has a Gigabit Ethernet MAC. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SuperH has the "CONFIG_CPU_LITTLE_ENDIAN" and the "__LITTLE_ENDIAN__".
But, other architecture doesn't have them. So, this patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add define of SH7734 register and sh_eth_reset_hw_crc function.
V3: Rebase net/HEAD.
V2: Do not split line of #if defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers have TSU. It can register one VLAN tag, and it can
filter other VLAN tag by hardware.
If vlan_rx_add_vid() is called twice or more, the driver will disable
the filtering.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers have TSU. It can filter multicast by hardware.
This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the controller has TSU, the each channel needs TSU registers.
This patch also fixes the iounmap condition in the sh_eth_drv_remove().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7757 has 2 Fast Ethernet and 2 Gigabit Ethernet, and the first
Gigabit channel needs the initialization. So, this patch adds the
parameter of "needs_init", and if the sh_eth_plat_data is set it
to 1, the driver will initialize the channel.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7757's GETHER has TSU registers. So, this patch adds the value
of ".tsu = 1" in the sh_eth_cpu_data.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove double include of linux/interrupt.h.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to maintain a parallel net_device_stats structure in
sh_eth_private, since we have a generic one in netdev
Fix two dma_map_single() incorrect parameters, passing skb->tail instead
of skb->data. Seems that there is no corresponding dmap_unmap_single()
calls for the moment in this driver.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov