[This version fixes a thinko in the r8a66597 driver]
This patch let a few discrete USB host controllers drivers (isp116x-hcd,
r8a66597-hcd and sl811-hcd) obtain IRQ flags from their IORESOURCE_IRQ
resource if configured as such, much like it's been done for the smc91x
driver.
It spares people writing support for specific boards the burden to
configure the interrupt controller independantly, and keeps all IRQ
related information in a single resource.
HCD that are integrally part of a SoC have been left aside, as there
is probably no "wiring" options...
Tested on an Xscale PXA-255 based platform with isp116x-hcd.
Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this extends the poisoning concept to anchors. This way poisoning
will work with fire and forget drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
looking at usb_kill_urb() it seems to me that it is unnecessarily lenient.
In the use case of disconnect() you never want to use the URB again
(for the same device) But leaving urb->reject elevated will make it easier
to avoid races between read/write and disconnect.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, it is possible to tell statically whether usblp will be NULL
in the error handling code.
Oliver Neukum suggested to make a goto to the final return rather than
return directly.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier f,err,l,l1;
type T;
expression x,E;
statement S;
@@
x = NULL
... when != goto l1;
* x = f(...)
... when != x
err = E;
goto l;
...
* if (x != NULL)
S
return err;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver was originaly written by Stefan Kopp, but massively
reworked by Greg for submission.
Thanks to Felipe Balbi <me@felipebalbi.com> for lots of work in cleaning
up this driver.
Thanks to Oliver Neukum <oliver@neukum.org> for reviewing previous
versions and pointing out problems.
Cc: Stefan Kopp <stefan_kopp@agilent.com>
Cc: Marcel Janssen <korgull@home.nl>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added basic support for a Delcom USB 7-segment LED Display
Signed-off by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Oceanic PID to ftdi_sio driver
Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a PID of 0xf460. The
attached patch adds that pid to ftdi_sio; driver connects to my VT3
after that.
Signed-off-by: Vladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate device ids which are now supported by drivers/usb/net/hso.c
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (47 commits)
hwmon: (adm1026) Prevent log spamming
hwmon: (adm1026) Fix debug messages
hwmon: (adm1029) Use mask for fan_div value
hwmon: (adt7470) Add documentation
hwmon: (ibmaem) Automatically load on IBM systems via DMI
hwmon: (ibmpex) Automatically load on IBM systems via DMI
hwmon: (w83781d) Use new style driver binding
hwmon: (w83781d) Stop abusing struct i2c_client for ISA devices
hwmon: (w83781d) Make ISA interface depend on CONFIG_ISA
hwmon: (w83781d) Additional information about AS99127F PWM
hwmon: (w83781d) Detect alias chips
hwmon: (w83781d) Refactor beep enable handling
hwmon: Drop dead links to old National Semiconductor chip datasheets
hwmon: (w83791d) add support for thermal cruise mode
hwmon: (w83791d) add pwm_enable support
hwmon: (w83791d) add manual PWM support
hwmon: (w83791d) fan 4/5 pins can also be used for gpio
hwmon: (max1619) Use inline functions instead of macros
hwmon: (it87) Fix thermal sensor type values
hwmon: (lm78) Convert to a new-style i2c driver
...
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove __generic_unplug_device() from exports
block: move q->unplug_work initialization
blktrace: pass zfcp driver data
blktrace: add support for driver data
block: fix current kernel-doc warnings
block: only call ->request_fn when the queue is not stopped
block: simplify string handling in elv_iosched_store()
block: fix kernel-doc for blk_alloc_devt()
block: fix nr_phys_segments miscalculation bug
block: add partition attribute for partition number
block: add BIG FAT WARNING to CONFIG_DEBUG_BLOCK_EXT_DEVT
softirq: Add support for triggering softirq work on softirqs.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add at least the bare minimum of documentation for this chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.
[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350
This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Simplify the IRQ handling routine of ams driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Marc Zyngier