When register/unregister ae_dev, ae_dev should match all client
in the client_list. Enet and roce can co-exists together so we
should continue checking for enet and roce presence together.
So break should not be there.
Above caused problems in loading and unloading of modules.
Fixes: 38eddd126772 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no vlan id in the packets, hardware will treat the vlan id
as 0 and look for the mac_vlan table. This patch set the default vlan id
of PF as 0. Without this config, it will fail when look for mac_vlan
table, and hardware will drop packets.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the ethernet address copy instance with more
appropriate ether_addr_copy() function.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the initialization of MAC address, fetched from HNS3
firmware i.e. when it is not randomly generated, to the HNS3 hardware.
Fixes: ca60906d2795 ("net: hns3: Add support of HNS3 Ethernet Driver for
hip08 SoC")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the vector-to-ring map and unmap command and adds
INT_GL(for, Gap Limiting Interrupts) and VF id to it as required
by the hardware interface.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Mingguang Qu <qumingguang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the IMP command being used to unmap the vector
from the corresponding ring.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default phy address of every port is 0. Therefore, phy address for
each port need to be fetched from firmware and device initialized
with fetched non-default phy address.
Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine &
Compatibility Layer Support")
Signed-off-by: Lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the integration of PHYLINK, the configuration option which
used to be under the PHY infrastructure menu in menuconfig ended
up one level up (the network device driver section)
By placing PHYLINK option right after PHYLIB entry, it broke the
way Kconfig used to build the menu. See kconfig-language.txt, section
"Menu structure", 2nd method.
This is fixed by placing the PHYLINK option just before PHYLIB.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several problems with commit 10377ba767 ("net: systemport:
Support 64bit statistics", first one got fixed in 7095c97345 ("net:
systemport: Fix 64-bit stats deadlock").
The second problem is that this specific code updates the
stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we
are returning to ethtool -S. If we are not running a tool that involves
calling ndo_get_stats64(), then we won't get updated ethtool stats.
The solution to this is to update the stats from both call sites,
factoring that into a specific function, While at it, don't just check
the sizeof() but also the type of the statistics in order to use the
64-bit stats seqlock.
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems we have to be more careful in napi_complete_done()
use. This patch is not a revert, as it seems we can
avoid bug that Ville reported by moving the napi_complete_done()
test in the spinlock section.
Many thanks to Ville for detective work and all tests.
Fixes: 617f01211b ("8139too: use napi_complete_done()")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ingress-only qdisc for flower offload, as other qdiscs
are not supported for flower offload.
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clear Speed Selection in MDIO control register(0x10),
ie, clear bits 6 and 13 to zero while keeping other bits same.
Before AND operation,The Mask value has to be perform with bitwise NOT
operation (ie, ~ operator)
This patch clears current speed selection before writing the
new speed settings to gmii2rgmii converter
Fixes: f411a6160b ("net: phy: Add gmiitorgmii converter support")
Signed-off-by: Fahad Kunnathadi <fahad.kunnathadi@dexceldesigns.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* A couple of bugzilla bugs related to multicast handling;
* Two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems;
* Two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch;
* A fix for buffer reordering in the newly supported 9000 device
family;
* Fix a race when starting aggregation;
* Small fix for a recent patch to wake mac80211 queues;
* Send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlm7u44ACgkQoUecoho8
xfqOPw//TF8p9ZqXknYahiaSM8pQFSXbnbPCa8IFnZs4yTV7f6htQ50bRjafFsbV
nAUAXaJI3901QyP96yHKX09IYJ6QMFxiCiB2uFmwUdVw+WFRPd9fJMMIFYKKIQTp
2v3NA2odBrDzWZRp7HAipo6xQTkAEBqubrJqWMGLKoQUcMm7ocVLAazCj66dxbLd
onyunys2+8DU2krGdDTZA8vlcXWSWvMtDzvsB3yfB4Do0rG+jQj5CDeB6ou7VKtq
SvVr75qCc/4YHHCxWEU380Usdz36pgW22BVGp8OoAX1SRR26zpeT8g2FwiUIK8R/
0+vSmbOFnAkXDMezNGQ74tdTB/AoT43kymEq2fCxll7gPMLabuYkZhSIBgIj6rZs
KCcPcazP93CofTMpG9G/cLphsvGgB0WlYwQhcuUts3+goLKApvpbsKThWRPjsBW4
0VbH/TTDddaMEuDvm+I1wL49GiF1l2uLlzjuol9W2oM1MXnhFn/QXuntjrKKRwP0
XiLx07zjaS21jZaIJjRDf7LB02V/47YbJQ83p+kbDccKLhUOtSnbXmZsDfPRLWV+
klQF2kRusuZbVUrIvExKjJlloz1ydk6MnTP4W31kEyqtNjr1m92oKRvx8vHIZ+A5
id6KWed8DZU1VM4yFQSt/4LltN7ewdjlRaSOO0WO/C51iHV/vsA=
=DM5q
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
First set of fixes for 4.14
* A couple of bugzilla bugs related to multicast handling;
* Two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems;
* Two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch;
* A fix for buffer reordering in the newly supported 9000 device
family;
* Fix a race when starting aggregation;
* Small fix for a recent patch to wake mac80211 queues;
* Send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save;
Pull networking fixes from David Miller:
1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.
2) Fix double-free in rmnet driver, from Dan Carpenter.
3) INET connection socket layer can double put request sockets, fix
from Eric Dumazet.
4) Don't match collect metadata-mode tunnels if the device is down,
from Haishuang Yan.
5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
be2net driver, from Suresh Reddy.
6) Fix scaling error in gen_estimator, from Eric Dumazet.
7) Fix 64-bit statistics deadlock in systemport driver, from Florian
Fainelli.
8) Fix use-after-free in sctp_sock_dump, from Xin Long.
9) Reject invalid BPF_END instructions in verifier, from Edward Cree.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
Documentation: link in networking docs
tcp: fix data delivery rate
bpf/verifier: reject BPF_ALU64|BPF_END
sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
sctp: fix an use-after-free issue in sctp_sock_dump
netvsc: increase default receive buffer size
tcp: update skb->skb_mstamp more carefully
net: ipv4: fix l3slave check for index returned in IP_PKTINFO
net: smsc911x: Quieten netif during suspend
net: systemport: Fix 64-bit stats deadlock
net: vrf: avoid gcc-4.6 warning
qed: remove unnecessary call to memset
tg3: clean up redundant initialization of tnapi
tls: make tls_sw_free_resources static
sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
MAINTAINERS: review Renesas DT bindings as well
net_sched: gen_estimator: fix scaling error in bytes/packets samples
nfp: wait for the NSP resource to appear on boot
nfp: wait for board state before talking to the NSP
...
The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.
This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.
Fixes: 65e65ec137 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Andreas Rammhold <andreas@rammhold.de>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default receive buffer size was reduced by recent change
to a value which was appropriate for 10G and Windows Server 2016.
But the value is too small for full performance with 40G on Azure.
Increase the default back to maximum supported by host.
Fixes: 8b5327975a ("netvsc: allow controlling send/recv buffer size")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network interface is kept running during suspend, the net core
may call net_device_ops.ndo_start_xmit() while the Ethernet device is
still suspended, which may lead to a system crash.
E.g. on sh73a0/kzm9g and r8a73a4/ape6evm, the external Ethernet chip is
driven by a PM controlled clock. If the Ethernet registers are accessed
while the clock is not running, the system will crash with an imprecise
external abort.
As this is a race condition with a small time window, it is not so easy
to trigger at will. Using pm_test may increase your chances:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test
# echo mem > /sys/power/state
To fix this, make sure the network interface is quietened during
suspend.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.
[ 5.780350] ================================
[ 5.784679] WARNING: inconsistent lock state
[ 5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[ 5.794561] --------------------------------
[ 5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 5.810175] (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[ 5.818327] {SOFTIRQ-ON-W} state was registered at:
[ 5.823278] bcm_sysport_get_stats64+0x17c/0x258
[ 5.828053] dev_get_stats+0x38/0xac
[ 5.831776] rtnl_fill_stats+0x30/0x118
[ 5.835761] rtnl_fill_ifinfo+0x538/0xe24
[ 5.839921] rtmsg_ifinfo_build_skb+0x6c/0xd8
[ 5.844430] rtmsg_ifinfo_event.part.5+0x14/0x44
[ 5.849201] rtmsg_ifinfo+0x20/0x28
[ 5.852837] register_netdevice+0x628/0x6b8
[ 5.857171] register_netdev+0x14/0x24
[ 5.861051] bcm_sysport_probe+0x30c/0x438
[ 5.865280] platform_drv_probe+0x50/0xb0
[ 5.869418] driver_probe_device+0x2e8/0x450
[ 5.873817] __driver_attach+0x104/0x120
[ 5.877871] bus_for_each_dev+0x7c/0xc0
[ 5.881834] bus_add_driver+0x1b0/0x270
[ 5.885797] driver_register+0x78/0xf4
[ 5.889675] do_one_initcall+0x54/0x190
[ 5.893646] kernel_init_freeable+0x144/0x1d0
[ 5.898135] kernel_init+0x8/0x110
[ 5.901665] ret_from_fork+0x14/0x2c
[ 5.905363] irq event stamp: 24263
[ 5.908804] hardirqs last enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[ 5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[ 5.925143] softirqs last enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[ 5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[ 5.939985]
[ 5.939985] other info that might help us debug this:
[ 5.946576] Possible unsafe locking scenario:
[ 5.946576]
[ 5.952556] CPU0
[ 5.955031] ----
[ 5.957506] lock(&syncp->seq#2);
[ 5.960955] <Interrupt>
[ 5.963604] lock(&syncp->seq#2);
[ 5.967227]
[ 5.967227] *** DEADLOCK ***
[ 5.967227]
[ 5.973222] 1 lock held by swapper/0/0:
[ 5.977092] #0: (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54
So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building an allmodconfig kernel with gcc-4.6, we get a rather
odd warning:
drivers/net/vrf.c: In function ‘vrf_ip6_input_dst’:
drivers/net/vrf.c:964:3: error: initialized field with side-effects overwritten [-Werror]
drivers/net/vrf.c:964:3: error: (near initialization for ‘fl6’) [-Werror]
I have no idea what this warning is even trying to say, but it does
seem like a false positive. Reordering the initialization in to match
the structure definition gets rid of the warning, and might also avoid
whatever gcc thinks is wrong here.
Fixes: 9ff7438460 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Semantic patch used to resolve this issue:
@@
expression e,e2; constant c;
statement S;
@@
e = kzalloc(e2, c);
if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Acked-by: Sudarsana Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tnapi is being initialized and then immediately updated and
hence the initialiation is redundant. Clean up the warning
by moving the declaration and initialization to the inside
of the for-loop.
Cleans up clang scan-build warning:
warning: Value stored to 'tnapi' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
The control process (NSP) may take some time to complete its
initialization. This is not a problem on most servers, but
on very fast-booting machines it may not be ready for operation
when driver probes the device. There is also a version of the
flash in the wild where NSP tries to train the links as part
of init. To wait for NSP initialization we should make sure
its resource has already been added to the resource table.
NSP adds itself there as last step of init.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Board state informs us which low-level initialization stages the card
has completed. We should wait for the card to be fully initialized
before trying to communicate with it, not only before we configure
passing traffic.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we did not check the flow dissector against a list of allowed
and supported flow key dissectors. This patch introduces such a list and
correctly rejects unsupported flow keys.
Fixes: 43f84b72c5 ("nfp: add metadata to each flow offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 TSO requests with extension hdrs are a problem to the
Lancer and BEx chips. Workaround is to disable TSO6 feature
for such packets.
Also in Lancer chips, MSS less than 256 was resulting in TX stall.
Fix this by disabling GSO when MSS less than 256.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A randconfig build caused a compile failure:
drivers/net/ethernet/nuvoton/w90p910_ether.c: In function 'w90p910_ether_close':
drivers/net/ethernet/nuvoton/w90p910_ether.c:580:2: error: implicit declaration of function 'free_irq'; did you mean 'free_uid'? [-Werror=implicit-function-declaration]
Adding the correct include fixes the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8b426dc54c ("bonding: remove hardcoded value") changed the
default value for tlb_dynamic_lb which lead to either broken ALB mode
(since tlb_dynamic_lb can be changed only in TLB) or setting TLB mode
with tlb_dynamic_lb equal to 0.
The first issue was recently fixed by setting tlb_dynamic_lb to 1 always
when switching to ALB mode, but the default value is still wrong and
we'll enter TLB mode with tlb_dynamic_lb equal to 0 if the mode is
changed via netlink or sysfs. In order to restore the previous behaviour
and default value simply remove the mode check around the default param
initialization for tlb_dynamic_lb which will always set it to 1 as
before.
Fixes: 8b426dc54c ("bonding: remove hardcoded value")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the offloading of mirred actions under
matchall classifiers, mlxsw would find the destination port
associated with the offloaded action and utilize it for undoing
the configuration.
Depending on the order by which ports are removed, it's possible that
the destination port would get removed before the source port.
In such a scenario, when actions would be flushed for the source port
mlxsw would perform an illegal dereference as the destination port is
no longer listed.
Since the only item necessary for undoing the configuration on the
destination side is the port-id and that in turn is already maintained
by mlxsw on the source-port, simply stop trying to access the
destination port and use the port-id directly instead.
Fixes: 763b4b70af ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure pause time to 0xffff when tx flow control enabled
Set pause time to 0xffff in the pause frame to indicate the
partner to stop sending the packets. When RX buffer frees up,
the device sends pause frame with pause time zero for partner to
resume transmission.
Fixes: 2f7ca802bd ("Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and
patches
-----BEGIN PGP SIGNATURE-----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=qHNs
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
Commit cbf5ecb305 ("net: bonding: Fix transmit load balancing in
balance-alb mode") tried to fix transmit dynamic load balancing in
balance-alb mode, which wasn't working after commit 8b426dc54c
("bonding: remove hardcoded value").
It turned out that my previous patch only fixed the case when
balance-alb was specified as bonding module parameter, and not when
balance-alb mode was set using /sys/class/net/*/bonding/mode (the most
common usage). In the latter case, tlb_dynamic_lb was set up according
to the default mode of the bonding interface, which happens to be
balance-rr.
This additional patch addresses this issue by setting up tlb_dynamic_lb
to 1 if "mode" is set to balance-alb through the sysfs interface.
I didn't add code to change tlb_balance_lb back to the default value for
other modes, because "mode" is usually set up only once during
initialization, and it's not worthwhile to change the static variable
bonding_defaults in bond_main.c to a global variable just for this
purpose.
Commit 8b426dc54c also changes the value of tlb_dynamic_lb for
balance-tlb mode if it is set up using the sysfs interface. I didn't
change that behavior, because the value of tlb_balance_lb can be changed
using the sysfs interface for balance-tlb, and I didn't like changing
the default value back and forth for balance-tlb.
As for balance-alb, /sys/class/net/*/bonding/tlb_balance_lb cannot be
written to. However, I think balance-alb with tlb_dynamic_lb set to 0
is not an intended usage, so there is little use making it writable at
this moment.
Fixes: 8b426dc54c ("bonding: remove hardcoded value")
Reported-by: Reinis Rozitis <r@roze.lv>
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Cc: stable@vger.kernel.org # v4.12+
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only need to wakeup the initiator after all sub-channels
are opened.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a virtual device is added dynamically (via host console), then
the vmbus sends an offer message for the primary channel. The processing
of this message for networking causes the network device to then
initialize the sub channels.
The problem is that setting up the sub channels needs to wait until
the subsequent subchannel offers have been processed. These offers
come in on the same ring buffer and work queue as where the primary
offer is being processed; leading to a deadlock.
This did not happen in older kernels, because the sub channel waiting
logic was broken (it wasn't really waiting).
The solution is to do the sub channel setup in its own work queue
context that is scheduled by the primary channel setup; and then
happens later.
Fixes: 732e49850c ("netvsc: fix race on sub channel creation")
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not handle correctly the access to the upper page
in case of SFP/SFP+ EEPROM. In that case the offset should be local
and the I2C address should be changed.
Fixes: 2ea109039c ("mlxsw: spectrum: Add support for access cable info via ethtool")
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a typo here so we accidentally free "skb" instead of "skbn".
It leads to a double free and a leak. After discussing with Subash,
it's better to just move the check before the allocation and avoid the
need to free.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"The iwlwifi firmware compat fix is in here as well as some other
stuff:
1) Fix request socket leak introduced by BPF deadlock fix, from Eric
Dumazet.
2) Fix VLAN handling with TXQs in mac80211, from Johannes Berg.
3) Missing __qdisc_drop conversions in prio and qfq schedulers, from
Gao Feng.
4) Use after free in netlink nlk groups handling, from Xin Long.
5) Handle MTU update properly in ipv6 gre tunnels, from Xin Long.
6) Fix leak of ipv6 fib tables on netns teardown, from Sabrina Dubroca
with follow-on fix from Eric Dumazet.
7) Need RCU and preemption disabled during generic XDP data patch,
from John Fastabend"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
bpf: make error reporting in bpf_warn_invalid_xdp_action more clear
Revert "mdio_bus: Remove unneeded gpiod NULL check"
bpf: devmap, use cond_resched instead of cpu_relax
bpf: add support for sockmap detach programs
net: rcu lock and preempt disable missing around generic xdp
bpf: don't select potentially stale ri->map from buggy xdp progs
net: tulip: Constify tulip_tbl
net: ethernet: ti: netcp_core: no need in netif_napi_del
davicom: Display proper debug level up to 6
net: phy: sfp: rename dt properties to match the binding
dt-binding: net: sfp binding documentation
dt-bindings: add SFF vendor prefix
dt-bindings: net: don't confuse with generic PHY property
ip6_tunnel: fix setting hop_limit value for ipv6 tunnel
ip_tunnel: fix setting ttl and tos value in collect_md mode
ipv6: fix typo in fib6_net_exit()
tcp: fix a request socket leak
sctp: fix missing wake ups in some situations
netfilter: xt_hashlimit: fix build error caused by 64bit division
netfilter: xt_hashlimit: alloc hashtable with right size
...
This reverts commit 95b80bf3db ("mdio_bus:
Remove unneeded gpiod NULL check"), this commit assumed that GPIOLIB
checks for NULL descriptors, so it's safe to drop them, but it is not
when CONFIG_GPIOLIB is disabled in the kernel. If we do call
gpiod_set_value_cansleep() on a GPIO descriptor we will issue warnings
coming from the inline stubs declared in include/linux/gpio/consumer.h.
Fixes: 95b80bf3db ("mdio_bus: Remove unneeded gpiod NULL check")
Reported-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't remove rx_napi specifically just before free_netdev(),
it's supposed to be done in it and is confusing w/o tx_napi deletion.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will make it explicit some messages are of the form:
dm9000_dbg(db, 5, ...
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Rx rate select control gpio property name match the documented
binding. This would make the addition of 'rate-select1-gpios' for SFP+
support more natural.
Also, make the MOD-DEF0 gpio property name match the documentation.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few fixes to regressions introduced in the last one or two releases.
The iwlwifi fix is for a regression reported by Linus.
rtlwifi
* fix two antenna selection related bugs
iwlwifi
* fix regression with older firmwares
brcmfmac
* workaround firmware crash for bcm4345
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZsrqPAAoJEG4XJFUm622bT04IAIR/MiSKo+IJ8wpvzXJ5K7x5
/IzGDoJofqiQHVG0Rc72+0ooFwSe6nxQ3E+OzQM9yLIC8XcjPwd8mqnV4dzF5rIs
Q0ou092eBOVfMZO9EMrZJLuFiItfF8deH+nnYDuQBFsTHVKdkYVltB5JUX98hj6q
SFY7RYgmTcXq7j5H5u7AuDueJu0maHq2eb9t6MvtD06pbyvmh5t6CRsSORinMfff
090mWhPYTgZZqCuVQk9lki2671vgqjqfyr2M0hGWnsQCM+IiXUIptSGPEjwRDGDv
0yePGq750YPVjlMixIHfKEfm446YHp++Yjl/QzYCV3bbCHF5yEAUVoG8Nv3ibxc=
=DL06
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Few fixes to regressions introduced in the last one or two releases.
The iwlwifi fix is for a regression reported by Linus.
rtlwifi
* fix two antenna selection related bugs
iwlwifi
* fix regression with older firmwares
brcmfmac
* workaround firmware crash for bcm4345
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware feature check introduced for multi-scheduled scan is also
failing for bcm4345 devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The condition to check if reorder buffer ran out of
space is faulty, as it takes into account only the
NSSN.
In case the head SN was too far behind the reorder
buffer should move forward, regardless of the NSSN
status.
This caused the driver to release packets out of order
in some scenarios.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always must set the status to what we consider success before
calling iwl_mvm_send_cmd_status() (also iwl_mvm_send_cmd_pdu_status()
which calls it). Fix a few places where initialization is missing.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always need to initialize the status argument to the success case
before calling iwl_mvm_send_cmd_status() or
iwl_mvm_send_cmd_pdu_status() (which calls the former) otherwise we
may get an uninitialized value back. In this case, we use
ADD_STA_SUCCESS as success.
Fixes: 732d06e9d9 ("iwlwifi: mvm: add station before allocating a queue")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were ignoring the FIF_ALLMULTI flag when setting the multicast
addresses with MCAST_FILTER_CMD. Check if this flag is set and enable
pass_all accordingly. We also need to set the count to 0 if pass_all
is enable so we don't pass addresses to the firmware when not needed
(as doing so causes an assert).
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196741
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255). So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:
WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_start_mac_queues() takes a bitmap of the queues to wake.
When deferred tx is purged, set the bit of the hw_queue so
the correct queue will be waken up.
Fixes: 7e39a00d59 ("iwlwifi: mvm: start mac queues when deferred tx frames are purged")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AP interfaces now send all non-bufferable frames using the broadcast
station. Thus allow them to use the probe queue and don't warn about
it.
Fixes: eb045e6e03 ("iwlwifi: mvm: Avoid deferring non bufferable frames")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting wowlan mac80211 requests flush w/o vif
and we ignore this request. As a result some packets
stay stuck in the queue and it may end up with a queue
hang.
Allow the driver to flush queues even if station isn't
specified.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we set disconnect on wowlan and run suspend/resume, will run
into:
...snipped
iwlwifi 0000:01:00.0: Failed to load firmware chunk!
iwlwifi 0000:01:00.0: Could not load the [0] uCode section
iwlwifi 0000:01:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
It is because we still keep IWL_MVM_STATUS_IN_HW_RESTART in
__iwl_mvm_resume. When mac80211 starts the device as
__iwl_mvm_mac_start(), we will miss iwl_mvm_restart_cleanup(mvm).
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
that are entirely function pointers (along with a couple designated
initializer fixes).
- For the structleak plugin, provide an option to perform zeroing
initialization of all otherwise uninitialized stack variables that are
passed by reference (Ard Biesheuvel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=3jxS
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This finishes the porting work on randstruct, and introduces a new
option to structleak, both noted below:
- For the randstruct plugin, enable automatic randomization of
structures that are entirely function pointers (along with a couple
designated initializer fixes).
- For the structleak plugin, provide an option to perform zeroing
initialization of all otherwise uninitialized stack variables that
are passed by reference (Ard Biesheuvel)"
* tag 'gcc-plugins-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: structleak: add option to init all vars used as byref args
randstruct: Enable function pointer struct detection
drivers/net/wan/z85230.c: Use designated initializers
drm/amd/powerplay: rv: Use designated initializers
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
-----BEGIN PGP SIGNATURE-----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=QYS4
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-09-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Back from a long absence, so we have a number of things:
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).
To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.
Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it. But we will update
this firmware soon, so it won't be a problem anymore.
Fixes: 7089ae634c ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex"),
the code turns on a call to exhalbtc_bind_bt_coex_withadapter(). This
routine contains a bug that causes incorrect antenna selection for those
HP laptops with only one antenna and an incorrectly programmed EFUSE.
These boxes are the ones that need the ant_sel module parameter.
Fixes: 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.13+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.
Fixes: bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.12+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-09-05
This series contains fixes for i40e only.
These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.
Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.
Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 183db4 ("drivers: net: xgene: Correct probe sequence handling")
changed the return type of xgene_enet_check_phy_handle() to void.
This patch, removes the return statement from the last line.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes configuring tx/rx delay values for ACPI.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes reading tx/rx delay values for ACPI.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function calls to kcalloc use wrong parameter order and incorrect flags
values. GFP_KERNEL is used instead of flags now and the order is corrected.
The change was done using the following coccinelle script:
@@
expression E1,E2;
type T;
@@
-kcalloc(E1, E2, sizeof(T))
+kcalloc(E2, sizeof(T), GFP_KERNEL)
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it
Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.
This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is no longer used, the logging function was changed by commit
fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPS_TX_INT_CAUSE[Bubble] is a normal condition for T6, hence
ignore this interrupt for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPS_STAT_CTL[CountPauseStatTx] and MPS_STAT_CTL[CountPauseStatRx]
only control whether or not Pause Frames will be counted as part
of the 64-Byte Tx/Rx Frame counters. These bits do not control
whether Pause Frames are counted in the Total Tx/Rx Frames/Bytes
counters.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
do not reuse the loop counter which is used iterate over
the ports, so that sched_tbl will be freed for all the ports.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename "generic_xdp" to "skb_xdp" to avoid confusing it with the
generic XDP which will be done at netif_receive_skb().
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reserve headroom unconditionally which could cause unnecessary
stress on socket memory accounting because of increased trusesize. Fix
this by only reserve extra headroom when XDP is set.
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though TC2QOS mapping is for switch egress queues, we need to
configure it correclty in order for the Broadcom tag ingress (CPU ->
switch) queue selection to work correctly since there is a 1:1 mapping
between switch egress queues and ingress queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull parisc updates from Helge Deller:
"Major changes include:
- Full support of the firmware Page Deallocation Table with
MADV_HWPOISON and MADV_SOFT_OFFLINE. A kernel thread scans
regularily for new bad memory pages.
- Full support for self-extracting kernel.
- Added UBSAN support.
- Lots of section mismatch fixes across all parisc drivers.
- Added examples for %pF and %pS usage in printk-formats.txt"
* 'parisc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (28 commits)
printk-formats.txt: Add examples for %pF and %pS usage
parisc: Fix up devices below a PCI-PCI MegaRAID controller bridge
parisc/core: Fix section mismatches
parisc/ipmi_si_intf: Fix section mismatches on parisc platform
parisc/input/hilkbd: Fix section mismatches
parisc/net/lasi_82596: Fix section mismatches
parisc/serio: Fix section mismatches in gscps2 and hp_sdc drivers
parisc: Fix section mismatches in parisc core drivers
parisc/parport_gsc: Fix section mismatches
parisc/scsi/lasi700: Fix section mismatches
parisc/scsi/zalon: Fix section mismatches
parisc/8250_gsc: Fix section mismatches
parisc/mux: Fix section mismatches
parisc/sticore: Fix section mismatches
parisc/harmony: Fix section mismatches
parisc: Wire up support for self-extracting kernel
parisc: Make existing core files reuseable for bootloader
parisc: Add core code for self-extracting kernel
parisc: Enable UBSAN support
parisc/random: Add machine specific randomness
...
In struct ieee80211_tx_info, control.vif pointer and rate_driver_data[0]
falls on the same place, depending on the union usage.
During the whole TX process, the union is referred to as a control struct,
which holds the vif that is later used in the tx flow, especially in order
to derive the used tx power.
Referring direcly to rate_driver_data[0] and assigning a value to it,
overwrites the vif pointer, hence making all later references irrelevant.
Moreover, rate_driver_data[0] isn't used later in the flow in order to
retrieve the channel that it is pointing to.
Cc: stable@vger.kernel.org
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull locking updates from Ingo Molnar:
- Add 'cross-release' support to lockdep, which allows APIs like
completions, where it's not the 'owner' who releases the lock, to be
tracked. It's all activated automatically under
CONFIG_PROVE_LOCKING=y.
- Clean up (restructure) the x86 atomics op implementation to be more
readable, in preparation of KASAN annotations. (Dmitry Vyukov)
- Fix static keys (Paolo Bonzini)
- Add killable versions of down_read() et al (Kirill Tkhai)
- Rework and fix jump_label locking (Marc Zyngier, Paolo Bonzini)
- Rework (and fix) tlb_flush_pending() barriers (Peter Zijlstra)
- Remove smp_mb__before_spinlock() and convert its usages, introduce
smp_mb__after_spinlock() (Peter Zijlstra)
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
locking/lockdep/selftests: Fix mixed read-write ABBA tests
sched/completion: Avoid unnecessary stack allocation for COMPLETION_INITIALIZER_ONSTACK()
acpi/nfit: Fix COMPLETION_INITIALIZER_ONSTACK() abuse
locking/pvqspinlock: Relax cmpxchg's to improve performance on some architectures
smp: Avoid using two cache lines for struct call_single_data
locking/lockdep: Untangle xhlock history save/restore from task independence
locking/refcounts, x86/asm: Disable CONFIG_ARCH_HAS_REFCOUNT for the time being
futex: Remove duplicated code and fix undefined behaviour
Documentation/locking/atomic: Finish the document...
locking/lockdep: Fix workqueue crossrelease annotation
workqueue/lockdep: 'Fix' flush_work() annotation
locking/lockdep/selftests: Add mixed read-write ABBA tests
mm, locking/barriers: Clarify tlb_flush_pending() barriers
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE and CONFIG_LOCKDEP_COMPLETIONS truly non-interactive
locking/lockdep: Explicitly initialize wq_barrier::done::map
locking/lockdep: Rename CONFIG_LOCKDEP_COMPLETE to CONFIG_LOCKDEP_COMPLETIONS
locking/lockdep: Reword title of LOCKDEP_CROSSRELEASE config
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE part of CONFIG_PROVE_LOCKING
locking/refcounts, x86/asm: Implement fast refcount overflow protection
locking/lockdep: Fix the rollback and overwrite detection logic in crossrelease
...
Pull x86 asm updates from Ingo Molnar:
- Introduce the ORC unwinder, which can be enabled via
CONFIG_ORC_UNWINDER=y.
The ORC unwinder is a lightweight, Linux kernel specific debuginfo
implementation, which aims to be DWARF done right for unwinding.
Objtool is used to generate the ORC unwinder tables during build, so
the data format is flexible and kernel internal: there's no
dependency on debuginfo created by an external toolchain.
The ORC unwinder is almost two orders of magnitude faster than the
(out of tree) DWARF unwinder - which is important for perf call graph
profiling. It is also significantly simpler and is coded defensively:
there has not been a single ORC related kernel crash so far, even
with early versions. (knock on wood!)
But the main advantage is that enabling the ORC unwinder allows
CONFIG_FRAME_POINTERS to be turned off - which speeds up the kernel
measurably:
With frame pointers disabled, GCC does not have to add frame pointer
instrumentation code to every function in the kernel. The kernel's
.text size decreases by about 3.2%, resulting in better cache
utilization and fewer instructions executed, resulting in a broad
kernel-wide speedup. Average speedup of system calls should be
roughly in the 1-3% range - measurements by Mel Gorman [1] have shown
a speedup of 5-10% for some function execution intense workloads.
The main cost of the unwinder is that the unwinder data has to be
stored in RAM: the memory cost is 2-4MB of RAM, depending on kernel
config - which is a modest cost on modern x86 systems.
Given how young the ORC unwinder code is it's not enabled by default
- but given the performance advantages the plan is to eventually make
it the default unwinder on x86.
See Documentation/x86/orc-unwinder.txt for more details.
- Remove lguest support: its intended role was that of a temporary
proof of concept for virtualization, plus its removal will enable the
reduction (removal) of the paravirt API as well, so Rusty agreed to
its removal. (Juergen Gross)
- Clean up and fix FSGS related functionality (Andy Lutomirski)
- Clean up IO access APIs (Andy Shevchenko)
- Enhance the symbol namespace (Jiri Slaby)
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
objtool: Handle GCC stack pointer adjustment bug
x86/entry/64: Use ENTRY() instead of ALIGN+GLOBAL for stub32_clone()
x86/fpu/math-emu: Add ENDPROC to functions
x86/boot/64: Extract efi_pe_entry() from startup_64()
x86/boot/32: Extract efi_pe_entry() from startup_32()
x86/lguest: Remove lguest support
x86/paravirt/xen: Remove xen_patch()
objtool: Fix objtool fallthrough detection with function padding
x86/xen/64: Fix the reported SS and CS in SYSCALL
objtool: Track DRAP separately from callee-saved registers
objtool: Fix validate_branch() return codes
x86: Clarify/fix no-op barriers for text_poke_bp()
x86/switch_to/64: Rewrite FS/GS switching yet again to fix AMD CPUs
selftests/x86/fsgsbase: Test selectors 1, 2, and 3
x86/fsgsbase/64: Report FSBASE and GSBASE correctly in core dumps
x86/fsgsbase/64: Fully initialize FS and GS state in start_thread_common
x86/asm: Fix UNWIND_HINT_REGS macro for older binutils
x86/asm/32: Fix regs_get_register() on segment registers
x86/xen/64: Rearrange the SYSCALL entries
x86/asm/32: Remove a bunch of '& 0xffff' from pt_regs segment reads
...
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-09-03
Here's one last bluetooth-next pull request for the 4.14 kernel:
- NULL pointer fix in ca8210 802.15.4 driver
- A few "const" fixes
- New Kconfig option for disabling legacy interfaces
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it similar to drivers like ipvlan / macvlan so it is easier to read.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it easier to find out the parent dev.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data format can be directly set from rmnet_newlink() since the
rmnet real dev info is already available.
Since __rmnet_get_real_dev_info() is no longer used in rmnet_config.c
after removal of those functions, move content to
rmnet_get_real_dev_info().
__rmnet_set_endpoint_config() is collapsed into
rmnet_set_endpoint_config() since only mux_id was being set additionally
within it. Remove an unnecessary mux_id check.
Set the mux_id for the rmnet_dev within rmnet_vnd_newlink() itself.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current log is not very useful as it does not log the device
name since it it is prior to registration -
(unnamed net_device) (uninitialized): Setting up device
Modify to log after the device registration -
rmnet1: rmnet dev created
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was used only in the original patch series where the IOCTLs were
present and is no longer in use.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rmnet_rtnl_validate() was checking for upto mux_id 254, however the
rmnet_devices devices could hold upto 32 entries only. Fix this by
increasing the size of the rmnet_devices.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we moved to updating representors from a workqueue grabbing
the RTNL somehow got lost in the process. Restore it, and make
sure RCU lock is not held while we are grabbing the RTNL. RCU
protects the representor table, so since we will be under RTNL
we can drop RCU lock as soon as we find the netdev pointer.
RTNL is needed for the dev_set_mtu() call.
Fixes: 2dff196224 ("nfp: process MTU updates from firmware flower app")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's reasonable to assume that if user selects to build the NFP
driver all offload capabilities will be enabled by default.
Change the CONFIG_NFP_APP_FLOWER to default to enabled.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_consume_skb_any() in place of dev_kfree_skb_any()
when control frame has been successfully processed in flower
and on the driver's main TX completion path.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since representors are now created with a separate callback
start/stop app callbacks can be moved again to their original
location. They are intended to app-specific init/clean up
over the control channel.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create representors after lower vNIC is registered and destroy
them before it is destroyed. Move the code out of start/stop
callbacks directly into vnic_init/clean callbacks. Make sure
SR-IOV callbacks don't try to create representors when lower
device does not exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only have one app callback for vNIC creation
and destruction. This is insufficient, because some actions
have to be taken before netdev is registered, after it's
registered and after it's unregistered. Old callbacks
were really corresponding to alloc/free actions. Rename
them and add proper init/clean. Apps using representors
will be able to use new callbacks to manage lifetime of
upper devices.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Tariq includes micro data path optimization for mlx5e
netdevice driver.
Mainly Tariq introduces the following changes to NAPI and RX handling
path of the driver:
- RX ring structure reorganizing
- Trivial code refactoring and optimization
- NAPI busy-poll for when fast UMR is in progress
- Non-atomic state operations in NAPI context
- Remove unnecessary fields from fast path structures
- page-cache micro optimization
- Rely on NAPI to avoid missing an IRQ for RX/TX shared NAPI contexts
- Stop NAPI when irq changes affinity
- Distribute RSS table among all RX rings
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZq3r/AAoJEEg/ir3gV/o+ZtwIAK6LcyUxNSa+Q8a7+57EIQgj
xwA76EG1x5MskZ30QRJpZG6VP6C2WEOtG0/WDi6yfEzZh5J0+clqVv1cHVIJIFhC
vB+0FCl8GIlTE/VMpRFqFTZapz6/BWCWNQEW3a1raHb026cpeRzq7c+g1x4lKXx5
RN0QhOd/G+yUz6A+xt6GCRlHsIkvFpigL90rhfQqcvg/T8QepxZ1trJiytpu2J51
OhEtnl9mIapgj0Z9nQMMKV+BnLSaJxlJ2j5xGWa5x8zuySrGv/P26TYDsAvYp8pV
+f9OgISoQr7d2mWyus3IYSi31F3AkbGE01K3vBQTXpyd8pdEqv5bzXXWJtQASeQ=
=dmvv
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-09-03
This series from Tariq includes micro data path optimization for mlx5e
netdevice driver.
Mainly Tariq introduces the following changes to NAPI and RX handling
path of the driver:
- RX ring structure reorganizing
- Trivial code refactoring and optimization
- NAPI busy-poll for when fast UMR is in progress
- Non-atomic state operations in NAPI context
- Remove unnecessary fields from fast path structures
- page-cache micro optimization
- Rely on NAPI to avoid missing an IRQ for RX/TX shared NAPI contexts
- Stop NAPI when irq changes affinity
- Distribute RSS table among all RX rings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces callbacks and tunnel type to offload GRE tunnels.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct mlxsw_sp_rif is a router-private structure, and therefore
everything related to it is as well: parameters, and derived RIF types
including loopbacks. IPIP module needs access to some details of
loopback interfaces, but exporting all the RIF shebang would create too
large an interface.
So instead export just the bare minimum necessary: accessors for RIF
index and underlay VRF ID.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These traps are generated for packets that fail checks for source IP,
encapsulation type, or GRE key. Trap these packets to CPU for follow-up
handling by the kernel, which will send ICMP destination unreachable
responses.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local route that points at IPIP's underlay device (decap route) can
be present long before the GRE device. Thus when an encap route is
added, it's necessary to look inside the underlay FIB if the decap route
is already present. If so, the current trap offload needs to be
withdrawn and replaced with a decap offload.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike encapsulation, which is represented by a next hop forwarding to
an IPIP tunnel, decapsulation is a type of local route. It is created
for local routes whose prefix corresponds to the local address of one of
offloaded IPIP tunnels. When the tunnel is removed (i.e. all the encap
next hops are removed), the decap offload is migrated back to a trap for
resolution in slow path.
This patch assumes that decap route is already present when encap route
is added. A follow-up patch will fix this issue.
Note that this patch only supports IPv4 underlay. Support for IPv6
underlay will be subject to follow-up work apart from this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing bits to recognize IPv6 next hops as IPIP ones to enable
offloading of IPv6 overlay encapsulation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces some common code for tracking of offloaded IP-in-IP
tunnels, and support for offloading IPv4 overlay encapsulating routes in
particular. A follow-up patch will introduce IPv6 overlay as well.
Offloaded tunnels are kept in a linked list of mlxsw_sp_ipip_entry
objects hooked up in mlxsw_sp_router. A network device that represents
the tunnel is used as a key to look up the corresponding IPIP entry.
Note that in the future, more general keying mechanism will be needed,
because parts of the tunnel information can be provided by the route.
IPIP entries are reference counted, because several next hops may end up
using the same tunnel, and we only want to offload it once.
Encapsulation path hooks into next hop handling. Routes that forward to
a tunnel are now considered gateway routes, thus giving them the same
treatment that other remote routes get. An IPIP next hop type is
introduced.
Details of individual tunnel types are kept in an array of
mlxsw_sp_ipip_ops objects. If a tunnel type doesn't match any of the
known tunnel types, the next-hop is not considered an IPIP next hop.
The list of IPIP tunnel types is currently empty, follow-up patches will
add support for GRE. Traffic to IPIP tunnel types that are not
explicitly recognized by the driver traps and is handled in slow path.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the router, some next hops may reference an encapsulating netdevice,
such as GRE or IPIP. To properly offload these next hops, mlxsw needs to
keep track of whether a given next hop is a regular Ethernet entry, or
an IP-in-IP tunneling entry.
To facilitate this book-keeping, add a type field to struct
mlxsw_sp_nexthop. There is, as of this patch, only one next hop type:
MLXSW_SP_NEXTHOP_TYPE_ETH. Follow-up patches will introduce the IP-in-IP
variant.
There are several places where next hops are initialized in the IPv4
path. Instead of replicating the logic at every one of them, factor it
out to a function mlxsw_sp_nexthop4_type_init(). The corresponding fini
is actually protocol-neutral, so put it to mlxsw_sp_nexthop_type_fini(),
but create a corresponding protocoled _fini function that dispatches to
the protocol-neutral one.
The IPv6 path is simpler, but for symmetry with IPv4, create the same
suite of functions with corresponding logic.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 counterpart of the previous patch: introduce a function to
determine whether a given route is a gateway route.
The new function takes a mlxsw_sp argument which follow-up patches will
use. Thus mlxsw_sp_fib6_entry_type_set() got that argument as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For IPv4 IP-in-IP offload, routes that direct traffic to IP-in-IP
devices need to be considered gateway routes as well. That involves a
bit more logic, so extract the current test to a separate function,
where the logic can be later added.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading L3 tunnels, an adjacency entry is created that loops the
packet back into the underlay router. Loopback interfaces then hold the
corresponding information and are created for IP-in-IP netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback RIFs, which will be introduced in a follow-up patch, differ
from other RIFs in that they do not have a FID associated with them.
To support this, demote FID allocation from mlxsw_sp_rif_create to
configure op of the existing RIF types, and likewise the FID release
from mlxsw_sp_rif_destroy to deconfigure op.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Details of individual tunnel types are kept in an array of
mlxsw_sp_ipip_ops objects. Follow-up patches will use the list to
determine whether a constructed RIF should be a loopback, and to decide
whether a next hop references a tunnel.
The list is currently empty, follow-up patches will add support for GRE.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spectrum_ipip module that will be introduced in the follow-up
patches needs to know the data type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support IPIP, the driver needs to be able to construct an IPIP
adjacency. Change mlxsw_reg_ratr_pack to take an adjacency type as an
argument. Adjust the one existing caller.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other interface types, loopback RIFs do not have MAC address. So
drop the corresponding argument from mlxsw_reg_ritr_pack() and move it
to a new function. Call that from callers of mlxsw_reg_ritr_pack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTDP register is used for configuring the tunnel decap properties of
NVE and IPinIP.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To implement IP-in-IP decapsulation, Spectrum uses LPM entries of type
IP2ME with tunnel validity bit and tunnel pointer set. The necessary
register fields are already available, so add a function to pack the
RALUE as appropriate.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enum is used with reg_ratr_trap_id, so move it next to the register
definition.
While at it, drop the enumerator initializers.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, adjacencies have always been of type Ethernet (with value of 0),
and thus there was no need to explicitly support RATR type. However to
support IP-in-IP adjacencies, this type and a suite of IP-in-IP-specific
attributes need to be added.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the register so that loopback RIFs can be created and loopback
properties specified.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error injection it was possible to crash in dsa_loop_exit() because of
an attempt to unregister an invalid PHY. We actually want to the driver probing
in dsa_loop_init() even though fixed_phy_register() may return an error to
exercise how DSA deals with such cases, but we should not be crashing during
driver removal.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a mac address described in the device tree, a check is made
to see if it is valid. When it's not, no fallback is defined. This
patches tries to get the mac address from h/w (or use a random one if
the h/w one isn't valid) when the dt mac address isn't valid.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC retrieval logic is using a variable to store an h/w stored mac
address and checks this mac against invalid ones before using it. But
the mac address is only read from h/w when using PPv2.1. So when using
PPv2.2 it defaults to its init state.
This patches fixes the logic to only check if the h/w mac is valid when
actually retrieving a mac from h/w.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC retrieval has a quite complicated logic (which is broken). Moves
it to its own function to prepare for patches fixing its logic, so that
reviews are easier.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZqBDtAAoJELgmozMOVy/dNlcQAJhYNRGaNUBx0L6+8t2xwUrt
7ndP6qlMar30DJY9FjTQCzRBw0CRMWkXdJD8rYlyaHy07pjWDKG8LZtxEXu1FLdZ
oNRvQX6ZJh8Bz7db2SQFBCTF2uWGZZFqWQCrSbQwjj9xxjMDs59u/knmwHVY9dKk
egjPG4IQBDmcTeNY7h1otG2hXpx7QPIOilQW2EFN5SWAuBAazdF2JKxjjxqhnUfp
gD2pSdgsm3VSMoo0zpMa6qOP+9GcOu8J97fYFhasRYWCavPdWHyq+XNu9S/eicRd
xbv+seCYM+9jPb2dsNdjEKll7w3yyWdu7h6tSCMPYv54eN9sDDiO1w2L2ZnESMZa
JRnSfB+HXru1r4RyHOTPO8peaNhYlR1V4u8bTS5G2dffbHis9BajkWoAR/oSiUcB
AIjIIDcdJFVGfpF9KIt/pEl+adHNgESibSijzOUYkyw6RNbPqDmdd7YakPHcQhKN
clE3zQfIsPRLWsToP/nkBE0tUd3tQocRuLy7ote7hXQK+0p7TBz0a6Kkj87MvX33
8dVbUI+q6WRlEY90l71y0ZdXy/AvkxkFxAc4Y7FQZyJxhEArTaKgfa5fmpRwVxBm
yi9baoYCspHNRNv6AO4IL86ZCJqmWBuch8CBY1n2X3h8IGfKYEZUAZ+T/mnTTeUq
A4joXduz94ZD4w23leD1
=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current allocation for dev->caps.spec_qps is for the size of the
pointer and not the size of the actual mlx4_spec_qps structure. Fix
this by using the correct size. Also splint allocation over a few
lines to make it cppcheck clean on overly wide lines.
Detected by CoverityScan, CID#1455222 ("Wrong sizeof argument")
Fixes: c73c8b1e47 ("net/mlx4_core: Dynamically allocate structs at mlx4_slave_cap")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structures hca_param and func_cap are not being kfree'd on an error
exit path causing two memory leaks. Fix this by jumping to the existing
free memory error exit path.
Detected by CoverityScan, CID#1455219, CID#1455224 ("Resource Leak")
Fixes: c73c8b1e47 ("net/mlx4_core: Dynamically allocate structs at mlx4_slave_cap")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In default, uniformly distribute the RSS indirection table entries
among all RX rings, rather than restricting this only to the rings
on the close NUMA node. irqbalancer would anyway dynamically override
the default affinities set to the RX rings.
This gives better multi-stream performance and CPU util.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
NAPI context keeps rescheduling on same CPU as long as it's busy.
This doesn't give the oppurtunity for changes in irq affinities
to take effect.
Fix that by calling napi_complete_done() upon a change in affinity.
This would stop the NAPI and reschedule it on the new CPU.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We used a channel state bit MLX5E_CHANNEL_NAPI_SCHED to make
sure no NAPI is missed when a channel's napi_schedule() is called
for completion events of the different channel's resources/rings
while NAPI is currently running.
Now, as similar mechanism is implemented in kernel,
("39e6c8208d7b net: solve a NAPI race"),
we obsolete our own implementation and rely on the return value
of napi_complete_done().
This patch removes a redundant overhead of atomic bit operations.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In XDP_TX flow, we now get back quicker to each page in page-cache,
and on some occasions refcount does not get back to 1 on time, causing
some costly page allocations.
Slightly increase the size of RX page-cache to significantly decrease
the chances for this to happen.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Avoid recycling an RX page if it moved to another NUMA node.
Add an ethtool counter to count such events.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As of current design, in each NAPI, only a single UMR WQE
completion could be available in the completion queue of the
the internal control operations (ICO) send queue, in addition
to nop operations that require no actions upon completion.
This renders the consume index obsolete, as the wqe_counter
field in CQE is sufficient.
This helps removing a memory barrier, and obsoletes the need
for tracking the num_wqebbs to update the consumer counter.
In addition, remove other unused fields in icosq struct:
pdev, dma_fifo_pc, and prev_cc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Separate the RX post WQEs function of the different RQ types.
This enables RQ type-specific optimizations in data-path.
Poll the ICOSQ completion queue only for Striding RQ,
and only when a UMR post completion could be possibly available.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The indication for a UMR WQE in progress is needed only within
the NAPI context, and hence no races possible and no need for
the use of atomic operations.
The only place the flag is read outside of NAPI context is
in closure flow, after RQ is disabled flag is no more accessed
in NAPI.
Use a boolean instead of a bit in ring state, so that its
non-atomic set operations do not race with the atomic sets of
the other bits.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rings enabled state change occurs in control path only, and is always
followed by a napi_sychronize(), so that following NAPIs read the
new value. This read does not need to be atomic.
The RQ auto-moderation bit is not set/cleared in data-path.
No need for atomic read, a regular read operation is sufficient.
In RQ creation time as well, there's no multiple threads trying
to access it yet, hence a regular read can be used.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor function mlx5e_lro_update_hdr() to reduce number of
branches.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
NAPI context handles different kinds of completion queues
(RX, TX, and others). Hence, upon a poll trial, some of them
might be empty.
Here we early-return upon empty completion queues, as well as
full rx buffer, and save unnecessary logic and memory barriers.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If a UMR post is in progress, it means that there's a missing
WQE in RQ, and that a completion will be shortly available in
ICO SQ completion queue. Prefer busy-poll to handle it as soon
as possible.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The dma offset of a MPWQE (Multi-Packet WQE) in memory region
is fixed for all rounds. Calculate it once on creation time,
instead of in runtime. This also obsoletes the wqe argument in
the function.
In addition, optimize dma_info iterator calculation.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In RX data-path, use memset() instead of loop assignment
to init the whole skbs_frags array.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Field is used only locally within the RQ create function.
The use of a local variable is sufficient.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In RX data-path, use shift operations instead of a regular multiplication
by stride size, as it is a power of two.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bring fast-path fields together, and combine RX WQE mutual
exclusive fields into a union.
Page-reuse and XDP are mutually exclusive and cannot be used at
the same time.
Use a union to combine their footprints.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The limit of setting receive indirection table value should be
the current number of channels, not the VRSS_CHANNEL_MAX.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of the following code, net->num_tx_queues equals to
VRSS_CHANNEL_MAX, and max_chn is less than or equals to VRSS_CHANNEL_MAX.
netvsc_drv.c:
alloc_etherdev_mq(sizeof(struct net_device_context),
VRSS_CHANNEL_MAX);
rndis_filter.c:
net_device->max_chn = min_t(u32, VRSS_CHANNEL_MAX, num_possible_rss_qs);
So this patch removes the unnecessary limit check before comparing
with "max_chn".
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The minus one and assignment to a local variable is not necessary.
This patch simplifies it.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the parameter, num_queue in
rndis_filter_set_rss_param(), which is no longer in use.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VF is attached then can still allow netvsc driver module to
be removed. Just have to make sure and do the cleanup.
Also, avoid extra rtnl round trip when calling unregister.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one routine for datapath up/down. Don't need to reopen
the rndis layer.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to how we configure the RSB (Receive Status Block) we also
need to set the TSB (Transmit Status Block) based on the host endian.
This was missing from the commit indicated below.
Fixes: 389a06bc53 ("net: systemport: Set correct RSB endian bits based on host")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is being assigned but is never used, so remove it.
Cleans up clang build warning:
"warning: Value stored to 'priv' is never read"
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the array bcm7xxx_suspend_cfg A on the stack, instead
make it static. Makes the object code smaller by over 300 bytes:
Before:
text data bss dec hex filename
6351 8146 0 14497 38a1 drivers/net/phy/bcm7xxx.o
After:
text data bss dec hex filename
5986 8210 0 14196 3774 drivers/net/phy/bcm7xxx.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the arrays port_ids on the stack, instead make them static.
Makes the object code smaller by over 700 bytes:
Before:
text data bss dec hex filename
28785 5832 192 34809 87f9 fman.o
After:
text data bss dec hex filename
27921 5992 192 34105 8539 fman.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver and hardware supports IPv6 offload, however it
isn't enabled. Set the NETIF_F_IPV6_CSUM feature to inform the
network layer that this driver can offload IPV6 TCP and UDP
checksums. This change has been tested on an Armada 370 and the
feature support confirmed with several device datasheets
including the Armada XP and Armada 3700.
Signed-off-by: Andrew Pilloud <andrewpilloud@igneoussystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few last patches for 4.14, nothing really major here.
Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
qtnfmac
* implement 64-bit DMA support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZqWycAAoJEG4XJFUm622bLCEH/RbIdVLXvC7AM/5RGE4p8fEL
WjtMaGK5T14+OwbWSrYbtLPszJKfAt5MoG0Xl+c0xt+n7a6J+8GlyfXdxkYexkUN
8gt0LlSU0ExDx+VOiRWM9XFKjKy0WPx6xPI86DLGcGB/ygiCMI3ueot/tilNBK7V
lu4a0lqFifoIOOHynBhwvrhgrnyk5B5EJCSalwCN4NmaFveWjTzrBRNyi6BPJRgv
3iR1URNfzUYDmYDYS1EXB6+01PBpznrMSSFB/mxNSv5iiC988pc0ebj+UDi5Ms8Y
91gxlgKCbPbVj+D4M/Rwg2sAnAVCCLcEeheF2TmL1KoVUFyMBGYtyRS0qIUeQRM=
=p+hy
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
Few last patches for 4.14, nothing really major here.
Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
qtnfmac
* implement 64-bit DMA support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the do while loop the integer counter retries will
always be zero and so the subsequent check to see if it is zero
is always true and therefore redundant. Remove the redundant check
and always return -EIO on this return path. Also unbreak the literal
string in dev_err message to clean up a checkpatch warning.
Detected by CoverityScan, CID#744279 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_uninit() call put_device (unconditionally) because of
of_mdio_find_bus() in mdio_mux_init.
But of_mdio_find_bus is only called if mux_bus is empty.
If mux_bus is set, mdio_mux_uninit will print a "refcount_t: underflow"
trace.
This patch add a get_device in the other branch of "if (mux_bus)".
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix an old information that mdio-mux-mmioreg can only handle
8bit registers.
This is not true anymore.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the driver version information because this information
is not useful in an upstream kernel driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix checkpatch warning about unnecessary 'out of memory'
message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix checkpatch warning about NULL Comparison style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the GoP link interrupt support for when a port isn't
connected to a PHY. Because of this the phylib callback is never called
and the link status management isn't done. This patch use the GoP link
interrupt in such cases to still have a minimal link management. Without
this patch ports not connected to a PHY cannot work.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not necessarily a PHY between the GoP and the physical port.
However, the driver currently makes the "phy" property mandatory,
contrary to what is stated in the device tree bindings. This patch makes
the PHY optional, and aligns the PPv2 driver on its device tree
documentation. However if a PHY is provided, the GoP link interrupt
won't be used.
With this patch switches directly connected to the serdes lanes and SFP
ports on the Armada 8040-db and Armada 7040-db can be used if the link
interrupt is described in the device tree.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all RGMII checks to use the phy_interface_mode_is_rgmii()
helper. This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abort mechanism is invoked a default route directing packets to
the CPU is programmed in all the virtual routers currently in use. This
can result in packet loss in case a new VRF is configured.
Upon abort, program the default route in all virtual routers, whether
they are in use or not.
The patch is directed at net-next since post-abort fixes aren't critical
and packet loss due to a missing default route will be insignificant
compared to packet loss caused by the CPU port policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I relied on the fact that anycast routes use the loopback device as
their nexthop device to trap packets hitting them to the CPU.
After commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address") this is no longer the case and such routes are
programmed with a forward action (note the 'offload' flag):
anycast cafe:: dev enp3s0np7 proto kernel metric 0 offload pref medium
This will prevent the router from locally receiving packets destined to
the Subnet-Router anycast address.
Fix this by specifically programming anycast routes with action trap,
which results in the following output:
anycast cafe:: dev enp3s0np7 proto kernel metric 0 pref medium
Fixes: 4832c30d54 ("net: ipv6: put host and anycast routes on device with address")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling IPv6 neighbor counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on IPv6 neighbors based on dpipe's host6
table counter status.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 host table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the host entry filler helper to be applicable for both IPv4/6
addresses.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper for accessing destination IP in case of IPv6 neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 host table initial support. The action behavior for both IPv4/6
tables is the same, thus the same action dump op is used. Neighbors with
link local address are ignored.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neighbors with link local addresses are not offloaded to the host table,
yet, the are maintained in the driver for adjacency table usage. When
dumping the IPv6 host neighbors this link local neighbors should be
ignored. This patch exports this helper for dpipe usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.14. Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
ACPI will rely on device driver to tell it if the device could support
wakeup function when system in D3 state.
This has caused some platform can't support remote wakeup correctly,
because the ACPI wakeup GPE is not enabled, hence registers the .set_wakeup
callback to handle it if device supports wakeup.
Tested with QCA6174 hw3.0, firmware ('WLAN.RM.4.4.1-00008-QCARMSWP-1')
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The actual PCI suspend/resume in ath10k has been handled in wow.c,
but in the case of the device doesn't support remote wakeup,
the .hif_suspend() and .hif_resume() will never be handled.
ath10k_wow_op_suspend()
{
if (WARN_ON(!test_bit(ATH10K_FW_FEATURE_WOWLAN_SUPPORT,
ar->running_fw->fw_file.fw_features))) {
ret = 1;
goto exit;
}
....
ret = ath10k_hif_suspend(ar);
}
So register the PCI PM core to support the suspend/resume if the device
doesn't support remote wakeup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Refactor code in order to avoid identical code for different branches.
Addresses-Coverity-ID: 1248728
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For debugging some problems, it is useful to know the chip revision
add a brcmf_info message logging this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use 64-bit dma for hosts with CONFIG_ARCH_DMA_ADDR_T_64BIT enabled.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check if skb tracking arrays has been already allocated. This additional
check handles the case when init partially failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NULL is not a special type of success here but a error pointer.
So it makes sense to check against NULL in qtnf_map_bar
and return error code.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linux built-in circ_buf implementation assumes that that the
circular buffer length is a power of 2. Make sure that
rx and tx descriptor queue lengths are power-of-2.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag -D__CHECK_ENDIAN was wrong: it should be -D__CHECK_ENDIAN__ instead.
However now this flag is enabled by default, so it can be removed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User space can remove the P2P management interface while it is active
(for example, while listen/search is active) and this can cause
a crash. Ensure the P2P device is fully stopped before removing.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Connect can take longer than current timeout in some scenarios,
for example with long-range antenna array. Increase the timeout
to support these scenarios.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW starts running it can get D0 to D3 interrupt that is a leftover
from previous system suspend while FW was not running.
As this interrupt is not relevant anymore, clear it part of device reset
procedure.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Re-arrange the code to have dedicated function for device configuration
which takes place before FW starts running.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since debugfs is a kernel configuration option, enable the driver to
compile without debugfs.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes there is a firmware crash but the hardware
is not fully stopped and continue to send TX/RX interrupts.
This can cause an overload of messages which can bring the
host down. Add ratelimit to these error messages to fix this.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 9f5bcfe933 ("ath10k: silence firmware file probing
warnings") the firmware loading was changed from request_firmware() to
request_firmware_direct() to silence some warnings in case it fails.
request_firmware_direct() directly searches in the file system only and
does not send a hotplug event to user space in case it could not find
the firmware directly.
In LEDE we use a user space script to extract the calibration data from
the flash memory which gets triggered by the hotplug event. This way the
firmware gets extracted from some vendor specific partition when the
driver requests this firmware. This mechanism does not work any more
after this change.
Fixes: 9f5bcfe933 ("ath10k: silence firmware file probing warnings")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
irq_wq in struct ath10k_sdio is a remnant from an earlier
version of the sdio patchset.
Its use was removed as a result of Kalle's review, but somehow
the struct member survived.
It is not used and can therefore safely be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In napi_poll, the budget number is used to control the amount of packets
we should handle per poll to balance the resource in the system.
In the list of the amsdu packets reception, we check if there is budget
count left and handle the complete list of the packets, that it will have
chances the very last list will over the budget leftover.
So adding one more parameter - budget_left, this would help while
traversing the list to avoid handling more than the budget given.
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Fix-suggested-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Link: https://lkml.kernel.org/r/26670dce-4dd2-f8e4-0e14-90d74257e739@virtuozzo.com
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This series provides the support for MPLS RSS and GRE TX offloads and
RSS support.
The first patch from Gal and Ariel provides the mlx5 driver support for
ConnectX capability to perform IP version identification and matching in
order to distinguish between IPv4 and IPv6 without the need to specify the
encapsulation type, thus perform RSS in MPLS automatically without
specifying MPLS ethertyoe. This patch will also serve for inner GRE IPv4/6
classification for inner GRE RSS.
2nd patch from Gal, Adds the TX offloads support for GRE tunneled packets,
by reporting the needed netdev features.
3rd patch from Gal, Adds GRE inner RSS support by creating the needed device
resources (Steering Tables/rules and traffic classifiers) to Match GRE traffic
and perform RSS hashing on the inner headers.
Improvement:
Testing 8 TCP streams bandwidth over GRE:
System: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 21.3 Gbps (Single RQ)
Now : 90.5 Gbps (RSS spread on 8 RQs)
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZp0JUAAoJEEg/ir3gV/o+nxkH+QFnIv26BZ/0aNQFyNJTRUqg
cGLIjCnlPUwVoy5U5zOIFTCdgGR/PUrzFcSa/qv9hjhprsvfs37V1R9B/2vVeJbr
TdEzvdIYnMHY+EhafkPWhuaUYO/Ng/W8VSnxXgJw2mpWL1wN4wF6c3f0X/YuG0Sa
uNAEmFe26TItD7P+vIzV8yQB/3tWZjQRbK2HcrHyd4qmuLjI9yVXsuyXzedJ8Ccn
YJAfKcshULeWRwMXh/QH+MYYtWbQ8FRKMhxOdTpeC//803xC2E1XFBHsRu8io1HA
kWJYDsFLC+v3vYjZ0JK9IAU4H9UBKh6lnd8BrjtbjJg0nuUJ3K3Lc80UZU/tEhU=
=L5m4
-----END PGP SIGNATURE-----
Merge tag 'mlx5-GRE-Offload' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-08-31 (GRE Offloads support)
This series provides the support for MPLS RSS and GRE TX offloads and
RSS support.
The first patch from Gal and Ariel provides the mlx5 driver support for
ConnectX capability to perform IP version identification and matching in
order to distinguish between IPv4 and IPv6 without the need to specify the
encapsulation type, thus perform RSS in MPLS automatically without
specifying MPLS ethertyoe. This patch will also serve for inner GRE IPv4/6
classification for inner GRE RSS.
2nd patch from Gal, Adds the TX offloads support for GRE tunneled packets,
by reporting the needed netdev features.
3rd patch from Gal, Adds GRE inner RSS support by creating the needed device
resources (Steering Tables/rules and traffic classifiers) to Match GRE traffic
and perform RSS hashing on the inner headers.
Improvement:
Testing 8 TCP streams bandwidth over GRE:
System: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 21.3 Gbps (Single RQ)
Now : 90.5 Gbps (RSS spread on 8 RQs)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix crash in linux PF driver when BARs have been cleared/de-programmed;
fail early init (prior to mapping BARs) if the BAR0 or
BAR1 registers are zero.
This situation can arise when the PF is added to a VM (PCI pass-through),
then a PF FLR is issued (in the VM). After this occurs, the BAR registers
will be zero. If we attempt to load the PF driver in the host
(after VM has been shutdown), the host can reset.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7ad813f208 ("net: phy:
Correctly process PHY_HALTED in phy_stop_machine()") because it is
creating the possibility for a NULL pointer dereference.
David Daney provide the following call trace and diagram of events:
When ndo_stop() is called we call:
phy_disconnect()
+---> phy_stop_interrupts() implies: phydev->irq = PHY_POLL;
+---> phy_stop_machine()
| +---> phy_state_machine()
| +----> queue_delayed_work(): Work queued.
+--->phy_detach() implies: phydev->attached_dev = NULL;
Now at a later time the queued work does:
phy_state_machine()
+---->netif_carrier_off(phydev->attached_dev): Oh no! It is NULL:
CPU 12 Unable to handle kernel paging request at virtual address
0000000000000048, epc == ffffffff80de37ec, ra == ffffffff80c7c
Oops[#1]:
CPU: 12 PID: 1502 Comm: kworker/12:1 Not tainted 4.9.43-Cavium-Octeon+ #1
Workqueue: events_power_efficient phy_state_machine
task: 80000004021ed100 task.stack: 8000000409d70000
$ 0 : 0000000000000000 ffffffff84720060 0000000000000048 0000000000000004
$ 4 : 0000000000000000 0000000000000001 0000000000000004 0000000000000000
$ 8 : 0000000000000000 0000000000000000 00000000ffff98f3 0000000000000000
$12 : 8000000409d73fe0 0000000000009c00 ffffffff846547c8 000000000000af3b
$16 : 80000004096bab68 80000004096babd0 0000000000000000 80000004096ba800
$20 : 0000000000000000 0000000000000000 ffffffff81090000 0000000000000008
$24 : 0000000000000061 ffffffff808637b0
$28 : 8000000409d70000 8000000409d73cf0 80000000271bd300 ffffffff80c7804c
Hi : 000000000000002a
Lo : 000000000000003f
epc : ffffffff80de37ec netif_carrier_off+0xc/0x58
ra : ffffffff80c7804c phy_state_machine+0x48c/0x4f8
Status: 14009ce3 KX SX UX KERNEL EXL IE
Cause : 00800008 (ExcCode 02)
BadVA : 0000000000000048
PrId : 000d9501 (Cavium Octeon III)
Modules linked in:
Process kworker/12:1 (pid: 1502, threadinfo=8000000409d70000,
task=80000004021ed100, tls=0000000000000000)
Stack : 8000000409a54000 80000004096bab68 80000000271bd300 80000000271c1e00
0000000000000000 ffffffff808a1708 8000000409a54000 80000000271bd300
80000000271bd320 8000000409a54030 ffffffff80ff0f00 0000000000000001
ffffffff81090000 ffffffff808a1ac0 8000000402182080 ffffffff84650000
8000000402182080 ffffffff84650000 ffffffff80ff0000 8000000409a54000
ffffffff808a1970 0000000000000000 80000004099e8000 8000000402099240
0000000000000000 ffffffff808a8598 0000000000000000 8000000408eeeb00
8000000409a54000 00000000810a1d00 0000000000000000 8000000409d73de8
8000000409d73de8 0000000000000088 000000000c009c00 8000000409d73e08
8000000409d73e08 8000000402182080 ffffffff808a84d0 8000000402182080
...
Call Trace:
[<ffffffff80de37ec>] netif_carrier_off+0xc/0x58
[<ffffffff80c7804c>] phy_state_machine+0x48c/0x4f8
[<ffffffff808a1708>] process_one_work+0x158/0x368
[<ffffffff808a1ac0>] worker_thread+0x150/0x4c0
[<ffffffff808a8598>] kthread+0xc8/0xe0
[<ffffffff808617f0>] ret_from_kernel_thread+0x14/0x1c
The original motivation for this change originated from Marc Gonzales
indicating that his network driver did not have its adjust_link callback
executing with phydev->link = 0 while he was expecting it.
PHYLIB has never made any such guarantees ever because phy_stop() merely just
tells the workqueue to move into PHY_HALTED state which will happen
asynchronously.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: David Daney <ddaney.cavm@gmail.com>
Fixes: 7ad813f208 ("net: phy: Correctly process PHY_HALTED in phy_stop_machine()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZpwI7AAoJEEg/ir3gV/o+9BUH+gJJb5D7kzkc+KH4vKr/TS9D
VMI/oDqhe44Eeag5d0gUjRF9You8708YRpCu6j3sHtnlfi9Ii21cjwd9P3QbshAn
vLt0EjL1fzrvqYjeBLYvbNxdK8qYViTWC6yigBYLKFWhQXdatVrqWhikqgtUw3/n
IP3IO5KUwUGDfGEMtbtdECNDrVM8NZIi9K/XFbkTHSIMzbi1qogiP8Ufdy2p1ORP
qq5mEorxHrGiMUqPAA8VLXsLDrnLRKnETokexUt/1dR0fJ32152mgeUniNxQvbs/
qnHdmMvnKaPofrFUrNqRCXtjOoxYhV0iv8eGyEv0Iz/hm3pitqr2M5rp1ZMffII=
=Rr1v
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-08-30
This series contains some misc fixes to the mlx5 driver.
Please pull and let me know if there's any problem.
For -stable:
Kernels >= 4.12
net/mlx5e: Fix CQ moderation mode not set properly
net/mlx5e: Don't override user RSS upon set channels
Kernels >= 4.11
net/mlx5e: Properly resolve TC offloaded ipv6 vxlan tunnel source address
Kernels >= 4.10
net/mlx5e: Fix DCB_CAP_ATTR_DCBX capability for DCBNL getcap
net/mlx5e: Check for qos capability in dcbnl_initialize
Kernels >= 4.9
net/mlx5e: Fix dangling page pointer on DMA mapping error
Kernels >= 4.8
net/mlx5e: Fix inline header size for small packets
net/mlx5: E-Switch, Unload the representors in the correct order
net/mlx5: Fix arm SRQ command for ISSI version 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7278 has only 128 entries while BCM7445 has the full 256 entries set,
fix that.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_start_xmit() might copy skb with inappropriate layout
into a fresh one.
Old skb is freed, and at this point it is not a drop, but
a consume. New skb will then be either consumed or dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new flow table and indirect TIRs which are used to hash the
inner packet headers of GRE tunneled packets.
When a GRE tunneled packet is received, the TTC flow table will match
the new IPv4/6->GRE rules which will forward it to the inner TTC table.
The inner TTC is similar to its counterpart outer TTC table, but
matching the inner packet headers instead of the outer ones (and does
not include the new IPv4/6->GRE rules).
The new rules will not add steering hops since they are added to an
already existing flow group which will be matched regardless of this
patch. Non GRE traffic will not be affected.
The inner flow table will forward the packet to inner indirect TIRs
which hash the inner packet and thus result in RSS for the tunneled
packets.
Testing 8 TCP streams bandwidth over GRE:
System: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 21.3 Gbps (Single RQ)
Now : 90.5 Gbps (RSS spread on 8 RQs)
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add TX offloads support for GRE tunneled packets by reporting the needed
netdev features.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This change adds the ability for flow steering to classify IPv4/6
packets with MPLS tag (Ethertype 0x8847 and 0x8848) as standard IP
packets and hit IPv4/6 classification steering rules.
Since IP packets with MPLS tag header have MPLS ethertype, they
missed the IPv4/6 ethertype rule and ended up hitting the default
filter forwarding all the packets to the same single RQ (No RSS).
Since our device is able to look past the MPLS tag and identify the
next protocol we introduce this solution which replaces ethertype
matching by the device's capability to perform IP version
identification and matching in order to distinguish between IPv4 and
IPv6.
Therefore, when driver is performing flow steering configuration on the
device it will use IP version matching in IP classified rules instead
of ethertype matching which will cause relevant MPLS tagged packets to
hit this rule as well.
If the device doesn't support IP version matching the driver will fall back
to use legacy ethertype matching in the steering as before.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Trivial fix to spelling mistake in DP_NOTICE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the wrong check being done for the phy device being
returned by the mdiobus_get_phy() function. This function never returns
the error pointers.
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet
Driver for hip08 SoC")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds logic to reconfigure the comphy/GoP/MAC when the link
state is updated at runtime. This is very useful on boards where many
link speed are supported: depending on what is negotiated the PPv2
driver will automatically reconfigures the link between the PHY and the
MAC.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link status changes, the phylib calls the link_event function
in the mvpp2 driver. Before this patch only the egress/ingress transmit
was enabled/disabled. This patch adds more functionality to the link
status management code by enabling/disabling the port per-cpu
interrupts, and the port itself. The queues are now stopped as well, and
the netif carrier helpers are called.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link_event function is somewhat complicated. This cosmetic patch
simplifies it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, the comphy is between the MAC GoP and the PHYs. The
mvpp2 driver currently relies on the firmware/bootloader to configure
the comphy. As a comphy driver was added to the generic PHY framework,
this patch uses it in the mvpp2 driver to configure the comphy at boot
time to avoid relying on the bootloader.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not hold a spinlock while pushing the skb into the networking
stack, so move the call to netif_rx_ni out of the critical region to where
we have dropped the spinlock.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device. This will be used to provide all MAP functionality
on future hardware in a single consistent location.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
cq_period_mode assignment was mistakenly removed so it was always set to "0",
which is EQE based moderation, regardless of the device CAPs and
requested value in ethtool.
Fixes: 6a9764efb2 ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix inline header size, make sure it is not greater than skb len.
This bug effects small packets, for example L2 packets with size < 18.
Fixes: ae76715d15 ("net/mlx5e: Check the minimum inline header mode before xmit")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When changing from switchdev to legacy mode, all the representor port
devices (uplink nic and reps) are cleaned up. Part of this cleaning
process is removing the neigh entries and the hash table containing them.
However, a representor neigh entry might be linked to the uplink port
hash table and if the uplink nic is cleaned first the cleaning of the
representor will end up in null deref.
Fix that by unloading the representors in the opposite order of load.
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently if vxlan tunnel ipv6 src isn't supplied the driver fails to
resolve it as part of the route lookup. The resulting encap header
is left with a zeroed out ipv6 src address so the packets are sent
with this src ip.
Use an appropriate route lookup API that also resolves the source
ipv6 address if it's not supplied.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, increasing the number of combined channels is changing
the RSS spread to use the new created channels.
Prevent the RSS spread change in case the user explicitly declare it,
to avoid overriding user configuration.
Tested:
when RSS default:
# ethtool -L ens8 combined 4
RSS spread will change and point to 4 channels.
# ethtool -X ens8 equal 4
# ethtool -L ens8 combined 6
RSS will not change after increasing the number of the channels.
Fixes: 8bf3686204 ('ethtool: ensure channel counts are within bounds during SCHANNELS')
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Function mlx5e_dealloc_rx_wqe is using page pointer value as an
indication to valid DMA mapping. In case that the mapping failed, we
released the page but kept the dangling pointer. Store the page pointer
only after the DMA mapping passed to avoid invalid page DMA unmap.
Fixes: bc77b240b3 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support for ISSI version 0 was recently broken as the arm_srq_cmd
command, which is used only for ISSI version 0, was given the opcode
for ISSI version 1 instead of ISSI version 0.
Change arm_srq_cmd to use the correct command opcode for ISSI version
0.
Fixes: af1ba291c5 ('{net, IB}/mlx5: Refactor internal SRQ API')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.
This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.
Fixes: e207b7e991 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.
On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.
Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling memcpy immediately after memset with the same region of memory
makes memset redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 41977e86c9 ("rt2x00: add support for MT7620") we do not
initialize TX_PIN_CFG setting. This cause breakage at least on some
RT3573 devices. To fix the problem patch restores previous behaviour
for non MT7620 chips.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1480829
Reported-and-tested-by: Jussi Eloranta <jussi.eloranta@csun.edu>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a missing unlock if rsi_find_sta() fails in
rsi_mac80211_ampdu_action() or if we hit the -EINVAL path in
rsi_mac80211_sta_add().
Fixes: 3528608f3a ("rsi: handle station connection in AP mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These devices support -34.ucode, so load it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use bcast station for all non bufferable frames on AP and AD-HOC.
The host is no longer aware of STAs PS status because of buffer
station offload, so we can't rely on mac80211 to toggle on
IEEE80211_TX_CTL_NO_PS_BUFFER bit.
A possible issue with buffering such frames, beside the obvious spec
violation, is when a station disconnects while in PS but the AP isn't
aware of that. In such scenarios the AP won't be able to send probe
responses or auth frames so the STA won't be able to reconnect and
the AP will have a queue hang.
Fixes: 3e56eadfb6 ("iwlwifi: mvm: implement AP/GO uAPSD support")
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debug print that sometimes reaches over
110 chars, thus generating a warning in those cases.
Split the print into two to prevent these cases.
Fixes: 92b0f7b26b ("iwlwifi: split the regulatory rules when the bandwidth flags require it")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A stray return was added in the macro bcmgenet_##name##_writel where it
should not, drop it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 69d2ea9c79 ("net: bcmgenet: Use correct I/O accessors")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy is connected at early stage of probe but not properly
disconnected if error occurs. This patch fixes the issue.
Also changing the return type of xgene_enet_check_phy_handle(),
since this function always returns success.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the nfp_net_pf_app_start() and the nfp_net_pci_probe() functions
call nfp_net_pf_app_stop_ctrl(pf) so there is a double free. The free
should be done from the probe function because it's allocated there so
I have removed the call from nfp_net_pf_app_start().
Fixes: 02082701b9 ("nfp: create control vNICs and wire up rx/tx")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a difference in the bit position of the normal interrupt summary
enable (NIE) and abnormal interrupt summary enable (AIE) between revisions
of the hardware. For older revisions the NIE and AIE bits are positions
16 and 15 respectively. For newer revisions the NIE and AIE bits are
positions 15 and 14. The effect in changing the bit position is that
newer hardware won't receive AIE interrupts in the current version of the
driver. Specifically, the driver uses this interrupt to collect
statistics on when a receive buffer unavailable event occurs and to
restart the driver/device when a fatal bus error occurs.
Update the driver to set the interrupt enable bit based on the reported
version of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.
Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)
Factor out the code to be shared by the NSH implementation.
NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should inform user about wrong firmware version
by printing message in dmesg.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the HW supports up to 32 multicast filters we should
track count of multicast filters to avoid overflow.
If we attempt to add >32 multicast filter - just set NETIF_ALLMULTI flag
instead.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Igor Russkikh <Igor.Russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver choose the optimal interrupt throttling settings depends
of current link speed.
Due this bug link_status field from aq_hw is never updated and as result
always used same interrupt throttling values.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has the HW Checksum Offload bug when small
TCP patckets (with length <= 60 bytes) has wrong "checksum valid" bit.
The solution is - ignore checksum valid bit for small packets
(with length <= 60 bytes) and mark this as CHECKSUM_NONE to allow
network stack recalculate checksum itself.
Fixes: ccf9a5ed14be ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of RSS queues should be not more than numbers of CPU.
Its does not make sense to increase perfomance, and also cause problems on
some motherboards.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes datapath spinlocks which does not perform any
useful work.
Fixes: 6e70637f9f1e ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for updating the FW on new port mac, when port mac change
is requested by the user. This info is required by the FW as OEM
management tools require this info directly from the NIC FW.
Check device capability bit to verify the FW supports user mac.
If the FW does support it, use set_port command to notify the FW on the
new mac.
The feature is relevant only to PF port mac.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lipeng