Commit Graph

118427 Commits

Author SHA1 Message Date
Mark Nelson 25d6e2d7c5 powerpc: Update 64bit memcpy() using CPU_FTR_UNALIGNED_LD_STD
Update memcpy() to add two new feature sections: one for aligning the
destination before copying and one for copying using aligned load
and store doubles.

These new feature sections will only affect Power6 and Cell because
the CPU feature bit was only added to these two processors.

Power6 gets its best performance in memcpy() when aligning neither the
source nor the destination, while Cell gets its best performance when
just the destination is aligned. But in order to save on CPU feature
bits we can use the previously added CPU_FTR_CP_USE_DCBTZ feature bit
to differentiate between Power6 and Cell (because CPU_FTR_CP_USE_DCBTZ
was added to Cell but not Power6).

The first feature section acts to nop out the branch that takes us to
the code that aligns us to an eight byte boundary for the destination.
We only want to nop out this branch on Power6.

So the ALT_FTR_SECTION_END() for this feature section creates a test
mask of the two feature bits ORed together and provides an expected
result of just CPU_FTR_UNALIGNED_LD_STD, thus we nop out the branch
if we're on a CPU that has CPU_FTR_UNALIGNED_LD_STD set and
CPU_FTR_CP_USE_DCBTZ unset.

For the second feature section added, if we're on a CPU that has the
CPU_FTR_UNALIGNED_LD_STD bit set then we don't want to do the copy
with aligned loads and stores (and the appropriate shifting left and
right instructions), so we want to nop out the branch to
.Lsrc_unaligned.

The andi. used for this branch is moved to just above the branch
because this allows us to nop out both instructions with just one
feature section which gives us better performance and doesn't hurt
readability which two separate feature sections did.

Moving the andi. to just above the branch doesn't have any noticeable
negative effect on the remaining 64bit processors (the ones that
didn't have this feature bit added).

On Cell this simple modification results in an improvement to measured
memcpy() bandwidth of up to 50% in the hot cache case and up to 15% in
the cold cache case.

On Power6 we get memory bandwidth results that are up to three times
faster in the hot cache case and up to 50% faster in the cold cache
case.

Commit 2a9294369b ("powerpc: Add new CPU
feature: CPU_FTR_CP_USE_DCBTZ") was where CPU_FTR_CP_USE_DCBTZ was
added.

To say that Cell gets its best performance in memcpy() with just the
destination aligned is true but only for the reason that the indirect
shift and rotate instructions, sld and srd, are microcoded on Cell.
This means that either the destination or the source can be aligned,
but not both, and seeing as we get better performance with the
destination aligned we choose this option.

While we're at it make a one line change from cmpldi r1,... to
cmpldi cr1,... for consistency.

Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:29 +11:00
Mark Nelson 4ec577a289 powerpc: Add new CPU feature: CPU_FTR_UNALIGNED_LD_STD
Add a new CPU feature bit, CPU_FTR_UNALIGNED_LD_STD, to be added
to the 64bit powerpc chips that can do unaligned load double and
store double without any performance hit.

This is added to Power6 and Cell and will be used in the next commit
to disable the code that gets the destination address aligned on
those CPUs where doing that doesn't improve performance.

Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:28 +11:00
Brian King 409001948d powerpc: Update page-in counter for CMM
A new field has been added to the VPA as a method for the client OS to
communicate to firmware the number of page-ins it is performing when
running collaborative memory overcommit.  The hypervisor will use this
information to better determine if a partition is experiencing memory
pressure and needs more memory allocated to it.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:28 +11:00
Sebastien Dugue 1ef8014deb powerpc/pseries: Fix getting the server number size
The 'ibm,interrupt-server#-size' properties are not in the cpu nodes,
which is where we currently look for them, but rather live under the
interrupt source controller nodes (which have "ibm,ppc-xics" in their
compatible property).

This moves the code that looks for the ibm,interrupt-server#-size
properties from xics_update_irq_servers() into xics_init_IRQ().

Also this adds a check for mismatched sizes across the interrupt
source controller nodes.  Not sure this is necessary as in this case
the firmware might be seriously busted.

This property only appears on POWER6 boxes and is only used in the
set-indicator(gqirm) call, and apparently firmware currently ignores
the value we pass.  Nevertheless we need to fix it in case future
firmware versions use it.

Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:28 +11:00
Anton Vorontsov 691de57679 powerpc: Remove device_type = "rtc" properties in .dts files
We don't want to encourage the device_type usage.  It isn't used in
the code, so we can simply remove it from the dts files.

Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:28 +11:00
Benjamin Herrenschmidt a6a8e009b1 powerpc: Silence software timebase sync
When no hardware method is provided to sync the timebase registers
across the machine, and the platform doesn't sync them for us, then we
use a generic software implementation.  Currently, the code for that
has many printks, and they don't have log levels.  Most of the printks
are only useful for debugging the code, and since we haven't had any
problems with it for years, this turns them into pr_debug.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:28 +11:00
Benjamin Herrenschmidt 1fd0f52583 powerpc: Fix domain numbers in /proc on 64-bit
The code to properly expose domain numbers in /proc is somewhat
bogus on ppc64 as it depends on the "buid" field being non-0,
but that field is really pseries specific.

This removes that code and makes ppc64 use the same code as 32-bit
which effectively decides whether to expose domains based on
ppc_pci_flags set by the platform, and sets the default for 64-bit
to enable domains and enable compatibility for domain 0 (which
strips the domain number for domain 0 to help with X servers).

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 22:08:27 +11:00
Stephen Rothwell 454666eb78 powerpc: Fix "unused variable" warning in pci_dlpar.c
This gets rid of this build warning:

arch/powerpc/platforms/pseries/pci_dlpar.c: In function 'init_phb_dynamic':
arch/powerpc/platforms/pseries/pci_dlpar.c:192: warning: unused variable 'b'

This is one of the very few warnings left in a ppc64_defconfig build and
getting rid of it will make it easier to see future introduced ones (in
fact this was introduced very recently).

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 19:59:08 +11:00
Alexey Dobriyan 9c8b4aff18 powerpc/cell: Fix compile error in ras.c
This fixes this error on Cell when CONFIG_KEXEC = n:

arch/powerpc/platforms/cell/ras.c:299: error: implicit declaration of function 'crash_shutdown_register'

We have to include <asm/kexec.h> because it contains the dummy
definition of crash_shutdown_register that is used when
CONFIG_KEXEC=n, but <linux/kexec.h> doesn't include <asm/kexec.h> in
that case.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 19:59:08 +11:00
Alexey Dobriyan fce4d58353 powerpc/ps3: Fix compile error in ps3-lpm.c
Compiling with CONFIG_SMP = n and CONFIG_PS3_LPM != n gives this error:

drivers/ps3/ps3-lpm.c:838: error: implicit declaration of function 'get_hard_smp_processor_id'

This fixes it.  We have to include <asm/smp.h> rather than
<linux/smp.h> because the UP definition of get_hard_smp_processor_id()
is in <asm/smp.h>, and <linux/smp.h> only includes <asm/smp.h> if
CONFIG_SMP = y.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-11-05 19:59:08 +11:00
Linus Torvalds 75fa67706c Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  xfrm: Fix xfrm_policy_gc_lock handling.
  niu: Use pci_ioremap_bar().
  bnx2x: Version Update
  bnx2x: Calling netif_carrier_off at the end of the probe
  bnx2x: PCI configuration bug on big-endian
  bnx2x: Removing the PMF indication when unloading
  mv643xx_eth: fix SMI bus access timeouts
  net: kconfig cleanup
  fs_enet: fix polling
  XFRM: copy_to_user_kmaddress() reports local address twice
  SMC91x: Fix compilation on some platforms.
  udp: Fix the SNMP counter of UDP_MIB_INERRORS
  udp: Fix the SNMP counter of UDP_MIB_INDATAGRAMS
  drivers/net/smc911x.c: Fix lockdep warning on xmit.
2008-11-04 08:30:12 -08:00
Linus Torvalds 4edfd20faf Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: mask off DET when restoring SControl for detach
  libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
  libata: Fix a potential race condition in ata_scsi_park_show()
  sata_nv: fix generic, nf2/3 detection regression
  sata_via: restore vt*_prepare_host error handling
  sata_promise: add ATA engine reset to reset ops
2008-11-04 08:19:01 -08:00
Jianjun Kong 54074d5932 drivers: remove duplicated #include
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-04 08:18:19 -08:00
Tejun Heo 299246f9a2 libata: mask off DET when restoring SControl for detach
libata restores SControl on detach; however, trying to restore
non-zero DET can cause undeterministic behavior including PMP device
going offline till power cycling.  Mask off DET when restoring
SControl.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:33 -05:00
Tejun Heo 6a87e42e95 libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply it
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers.  Implement a horkage to skip the mod16 check and apply
it to the quantum device.

This is reported by John Clark in the following thread.

  http://thread.gmane.org/gmane.linux.ide/34748

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:27 -05:00
Elias Oltmanns a464189de3 libata: Fix a potential race condition in ata_scsi_park_show()
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:24 -05:00
Tejun Heo 3c324283e6 sata_nv: fix generic, nf2/3 detection regression
All three flavors of sata_nv's are different in how their hardreset
behaves.

* generic: Hardreset is not reliable.  Link often doesn't come online
  after hardreset.

* nf2/3: A little bit better - link comes online with longer debounce
  timing.  However, nf2/3 can't reliable wait for the first D2H
  Register FIS, so it can't wait for device readiness or classify the
  device after hardreset.  Follow-up SRST required.

* ck804: Hardreset finally works.

The core layer change to prefer hardreset and follow up changes
exposed the above issues and caused various detection regressions for
all three flavors.  This patch, hopefully, fixes all the known issues
and should make sata_nv error handling more reliable.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:11 -05:00
Marcin Slusarz 554d491de1 sata_via: restore vt*_prepare_host error handling
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it

catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:06 -05:00
Mikael Pettersson cadef677e4 sata_promise: add ATA engine reset to reset ops
Promise ATA engines need to be reset when errors occur.
That's currently done for errors detected by sata_promise itself,
but it's not done for errors like timeouts detected outside of
the low-level driver.

The effect of this omission is that a timeout tends to result
in a sequence of failed COMRESETs after which libata EH gives
up and disables the port. At that point the port's ATA engine
hangs and even reloading the driver will not resume it.

To fix this, make sata_promise override ->hardreset on SATA
ports with code which calls pdc_reset_port() on the port in
question before calling libata's hardreset. PATA ports don't
use ->hardreset, so for those we override ->softreset instead.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:03 -05:00
Alexey Dobriyan bbb770e7ab xfrm: Fix xfrm_policy_gc_lock handling.
From: Alexey Dobriyan <adobriyan@gmail.com>

Based upon a lockdep trace by Simon Arlott.

xfrm_policy_kill() can be called from both BH and
non-BH contexts, so we have to grab xfrm_policy_gc_lock
with BH disabling.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 19:11:29 -08:00
David S. Miller 19ecb6ba80 niu: Use pci_ioremap_bar().
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 17:05:16 -08:00
Eilon Greenstein ca8eac55fa bnx2x: Version Update
Updating the version

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:46:58 -08:00
Eilon Greenstein 12b56ea89e bnx2x: Calling netif_carrier_off at the end of the probe
netif_carrier_off was called too early at the probe. In case of failure
or simply bad timing, this can cause a fatal error since linkwatch_event
might run too soon.

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:46:40 -08:00
Eilon Greenstein 7d96567ac0 bnx2x: PCI configuration bug on big-endian
The current code read nothing but zeros on big-endian (wrong part of the
32bits). This caused poor performance on big-endian machines. Though this
issue did not cause the system to crash, the performance is significantly
better with the fix so I view it as critical bug fix.

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:46:19 -08:00
Eilon Greenstein 9a0354405f bnx2x: Removing the PMF indication when unloading
When the PMF flag is set, the driver can access the HW freely. When the
driver is unloaded, it should not access the HW. The problem caused fatal
errors when "ethtool -i" was called after the calling instance was unloaded
and another instance was already loaded

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 16:45:55 -08:00
Lennert Buytenhek ee04448d88 mv643xx_eth: fix SMI bus access timeouts
The mv643xx_eth mii bus implementation uses wait_event_timeout() to
wait for SMI completion interrupts.

If wait_event_timeout() would return zero, mv643xx_eth would conclude
that the SMI access timed out, but this is not necessarily true --
wait_event_timeout() can also return zero in the case where the SMI
completion interrupt did happen in time but where it took longer than
the requested timeout for the process performing the SMI access to be
scheduled again.  This would lead to occasional SMI access timeouts
when the system would be under heavy load.

The fix is to ignore the return value of wait_event_timeout(), and
to re-check the SMI done bit after wait_event_timeout() returns to
determine whether or not the SMI access timed out.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-03 15:23:15 -05:00
Jeff Kirsher 1d19ecfc65 net: kconfig cleanup
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-03 15:23:12 -05:00
Alexey Dobriyan 7385d59575 fs_enet: fix polling
1. compile fix for irqreturn_t type change
2. restore ->poll_controller after CONFIG_PPC_CPM_NEW_BINDING transition

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-03 15:23:02 -05:00
Linus Torvalds a75952b72a Merge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: fix renaming one hardlink on top of another
  [CIFS] fix error in smb_send2
  [CIFS] Reduce number of socket retries in large write path
2008-11-03 11:43:59 -08:00
Jeff Layton ae6884a9da cifs: fix renaming one hardlink on top of another
cifs: fix renaming one hardlink on top of another

POSIX says that renaming one hardlink on top of another to the same
inode is a no-op. We had the logic mostly right, but forgot to clear
the return code.

Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
2008-11-03 18:31:05 +00:00
Linus Torvalds 457d2ee225 Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing, ring-buffer: add paranoid checks for loops
  ftrace: use kretprobe trampoline name to test in output
  tracing, alpha: undefined reference to `save_stack_trace'
2008-11-03 10:21:40 -08:00
Linus Torvalds da4a22cba7 Merge branch 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  io mapping: clean up #ifdefs
  io mapping: improve documentation
  i915: use io-mapping interfaces instead of a variety of mapping kludges
  resources: add io-mapping functions to dynamically map large device apertures
  x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps
2008-11-03 10:15:40 -08:00
Linus Torvalds 20ebc0073b Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda: make a STAC_DELL_EQ option
  ALSA: emu10k1 - Add more invert_shared_spdif flag to Audigy models
  ALSA: hda - Add a quirk for another Acer Aspire (1025:0090)
  ALSA: remove direct access of dev->bus_id in sound/isa/*
  sound: struct device - replace bus_id with dev_name(), dev_set_name()
  ALSA: Fix PIT lockup on some chipsets when using the PC-Speaker
  ALSA: rawmidi - Add open check in rawmidi callbacks
  ALSA: hda - Add digital-mic for ALC269 auto-probe mode
  ALSA: hda - Disable broken mic auto-muting in Realtek codes
2008-11-03 10:14:59 -08:00
Linus Torvalds c8126cc602 Merge branch 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc
* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
  proc: revert /proc/uptime to ->read_proc hook
2008-11-03 09:59:01 -08:00
Linus Torvalds 30ef898c53 Merge branch 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  i915: Add GEM ioctl to get available aperture size.
  drm/radeon: fixup further bus mastering confusion.
  build fix: CONFIG_DRM_I915=y && CONFIG_ACPI=n
2008-11-03 09:58:40 -08:00
Keith Packard e5beae1690 io mapping: clean up #ifdefs
Impact: cleanup

clean up ifdefs: change #ifdef CONFIG_X86_32/64 to
CONFIG_HAVE_ATOMIC_IOMAP.

flip around the #ifdef sections to clean up the structure.

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-11-03 18:21:45 +01:00
Keith Packard 8d5c6603c4 io mapping: improve documentation
Impact: add documentation

Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-11-03 18:21:44 +01:00
Takashi Iwai 7aeb6d7d20 Merge branches 'topic/fix/misc' and 'topic/fix/hda' into for-linus 2008-11-03 16:28:24 +01:00
Matthew Ranostay 6b3ab21ef1 ALSA: hda: make a STAC_DELL_EQ option
Add support for explicitly enabling the EQ distortion hack for
systems without software biquad support.

Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 14:29:47 +01:00
Steven Rostedt 818e3dd30a tracing, ring-buffer: add paranoid checks for loops
While writing a new tracer, I had a bug where I caused the ring-buffer
to recurse in a bad way. The bug was with the tracer I was writing
and not the ring-buffer itself. But it took a long time to find the
problem.

This patch adds paranoid checks into the ring-buffer infrastructure
that will catch bugs of this nature.

Note: I put the bug back in the tracer and this patch showed the error
      nicely and prevented the lockup.

Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-11-03 11:10:04 +01:00
Steven Rostedt b3aa557722 ftrace: use kretprobe trampoline name to test in output
Impact: ia64+tracing build fix

When a function is kprobed, the return address is set to the
kprobe_trampoline, or something similar. This caused the output
of the trace to look confusing when the parent seemed to be this
"kprobe_trampoline" function.

To fix this, Abhishek Sagar added a test of the instruction pointer
of the parent to see if it matched the kprobe_trampoline. If it
did, the output would print a "[unknown/kretprobe'd]" instead.

Unfortunately, not all archs do this the same way, and the trampoline
function may not be exported, which causes failures in builds.

This patch will compare the name instead of the pointer to see
if it matches. This prevents us from depending on a function from
being exported, and should work on all archs. The worst that can
happen is that an arch might use a different name and then we
go back to the confusing output. At least the arch will still build.

Reported-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Acked-by: Abhishek Sagar <sagar.abhishek@gmail.com>
2008-11-03 10:41:29 +01:00
Arnaud Ebalard a1caa32295 XFRM: copy_to_user_kmaddress() reports local address twice
While adding support for MIGRATE/KMADDRESS in strongSwan (as specified
in draft-ebalard-mext-pfkey-enhanced-migrate-00), Andreas Steffen
noticed that XFRMA_KMADDRESS attribute passed to userland contains the
local address twice (remote provides local address instead of remote
one).

This bug in copy_to_user_kmaddress() affects only key managers that use
native XFRM interface (key managers that use PF_KEY are not affected).

For the record, the bug was in the initial changeset I posted which
added support for KMADDRESS (13c1d18931
'xfrm: MIGRATE enhancements (draft-ebalard-mext-pfkey-enhanced-migrate)').

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Andreas Steffen <andreas.steffen@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 01:30:23 -08:00
Takashi Iwai 55e03a68d2 ALSA: emu10k1 - Add more invert_shared_spdif flag to Audigy models
Reported in Novell bnc#440862:
    https://bugzilla.novell.com/show_bug.cgi?id=440862

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 10:21:36 +01:00
Al Viro c2c8052946 tracing, alpha: undefined reference to `save_stack_trace'
Impact: build fix on !stacktrace architectures

only select STACKTRACE on architectures that have STACKTRACE_SUPPORT

... since we also need to ifdef out the guts of ftrace_trace_stack().
We also want to disallow setting TRACE_ITER_STACKTRACE in trace_flags
on such configs, but that can wait.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-11-03 10:12:13 +01:00
Takashi Iwai 69e50282b7 ALSA: hda - Add a quirk for another Acer Aspire (1025:0090)
Added a quirk for another Acer Aspier laptop (1025:0090) with ALC883
codec.  Reported in Novell bnc#426935:
    https://bugzilla.novell.com/show_bug.cgi?id=426935

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 10:07:43 +01:00
David S. Miller 55c8eb6c8e SMC91x: Fix compilation on some platforms.
This reverts 51ac3beffd ('SMC91x: delete
unused local variable "lp"') and adds __maybe_unused markers to these
(potentially) unused variables.

The issue is that in some configurations SMC_IO_SHIFT evaluates
to '(lp->io_shift)', but in some others it's plain '0'.

Based upon a build failure report from Manuel Lauss.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 00:19:31 -08:00
Takashi Iwai 0418ff0c8e ALSA: remove direct access of dev->bus_id in sound/isa/*
Removed the direct accesses of dev->bus_id in sound/isa/* by replacement
with dev_err() or dev_warn() functions.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 08:57:40 +01:00
Kay Sievers bb072bf098 sound: struct device - replace bus_id with dev_name(), dev_set_name()
[stripped sound/isa/* changes, replaced with the next patch -- tiwai]

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 08:57:33 +01:00
Zoltan Devai b02555c384 ALSA: Fix PIT lockup on some chipsets when using the PC-Speaker
Fix PIT lockup on some chipsets when using the PC-Speaker.

Signed-off-by: Zoltan Devai <zdevai@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 08:57:25 +01:00
Takashi Iwai 219df32fae ALSA: rawmidi - Add open check in rawmidi callbacks
The drivers (e.g. mtpav) may call rawmidi functions in irq handlers
even though the streams are not opened.  This results in Oops or panic.

This patch adds the rawmidi state check before actually operating the
rawmidi buffers.

Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2008-11-03 08:57:12 +01:00