Optimize _regulator_do_set_voltage() for the case selector is equal to
old_selector. Since the voltage does not change, we don't need to call
set_voltage_sel() and set_voltage_time_sel() in this case.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For cpufreq example, it takes 13 steps (25 mV for one step) to increase
vddcore from 0.95 V to 1.275 V, and the time of 64 clock cycles at
24 MHz for one step is ~2.67 uS, so the total delay time would be
~34.71 uS. But the current calculation in the driver gives 39 uS.
Change the formula to have the addition of 1 be the last step, so that
we can get a more precise delay time. For example above, the new
formula will give 35 uS.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code read "ti,warm_reset" of property twice, and set
pdata->reg_init[idx]->warm_reset twice. Read and set it once is enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For BUCK10 the control registers are wrongly set as buck9 control register
This patch corrects the control registers for buck10
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The dev parameter is the device requesting the data.
In this case it should be &pdev->dev rather than pdev->dev.parent.
The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(),
which means this fixes a memory leak because the memory is allocated every time
probe() is called, thus it should be freed when this driver is unloaded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
some of anatop's regulators(cpu, vddpu and vddsoc) have
register settings about LDO's step time, which will impact
the LDO ramp up speed, need to use set_voltage_time_sel
interface to add necessary delay everytime LDOs' voltage
is increased.
offset 0x170:
bit [24-25]: cpu
bit [26-27]: vddpu
bit [28-29]: vddsoc
field definition:
0'b00: 64 cycles of 24M clock;
0'b01: 128 cycles of 24M clock;
0'b02: 256 cycles of 24M clock;
0'b03: 512 cycles of 24M clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_find_node_by_name() returns a node pointer with refcount incremented, use
of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against from parameter,
thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dev parameter is the device requesting the data.
In this case it should be &pdev->dev rather than pdev->dev.parent.
The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(),
which means this fixes a memory leak because the memory is allocated every time
probe() is called, thus it should be freed when this driver is unloaded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_regulator_match() saves some dynamcially allocated state into the
match table that's passed to it. By implementation and not contract, for
each match table entry, if non-NULL state is already present,
of_regulator_match() will not overwrite it. of_regulator_match() is
typically called each time a regulator is probe()d. This means it is
called with the same match table over and over again if a regulator
triggers deferred probe. This results in stale, kfree()d data being left
in the match table from probe to probe, which causes a variety of crashes
or use of invalid data.
Explicitly free all output state from of_regulator_match() before
generating new results in order to avoid this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Add DT support for TI PMIC tps65090 regulator driver. The DT of this
device have node regulator and all regulator's node of this device is
added under this node.
The device tree binding document has the required information for
adding this device on DTS file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
of_get_gpio_regulator_config() is only used in gpio-regulator.c, make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Imagine a situation where a device tree has a few regulators in an
appropriate node:
regulators {
sw1 {
..
};
vvideo {
..
};
:
vfake {
..
};
vtypo {
..
};
};
In the above example, the node name "vfake" is an attempt to match a
regulator name inside the driver which just so happens to not exist. The
node name "vtypo" represents an accidental typographical error in a
regulator name which may have been introduced to a device tree.
In these cases, the number of regulators the mc13892 driver thinks it has
does not match the number of regulators it parsed and registered. Since
it will go over this array based on this number, it will actually
re-register regulator "0" (which happens to be SW1) over and over
again until it reaches the number, resulting in messages on the kernel
log such as these:
SW1: at 1100 mV
VVIDEO: at 2775mV
:
SW1: at 1100 mV
SW1: at 1100 mV
.. up to that number of "mismatched" regulators. Nobody using DT can/will
consume these regulators, so it should not be possible for it to cause any
real regulator problems or driver breakages, but it is an easy thing to
miss in a kernel log and is an immediate indication of a problem with the
device tree authoring.
This patch effectively sanity checks the number of counted children of
the regulators node vs. the number that actually matched driver names,
and sets the appropriate num_regulators value. It also gives a little
warning for device tree authors that they MAY have screwed something up,
such that this patch does not hide the device tree authoring problem.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MC13892 PMIC supports a "HI" bit for 3 of it's 4 buck switcher outputs,
which enables a higher set of voltage ranges.
Despite a comment in the code ('sw regulators need special care due to the
"hi" bit'), it actually does not take special care since it does not modify
it's use of the selector table index when this bit is set, giving us very
odd behavior when setting a high voltage on supported switchers or listing
current voltages. Net effect is in best case the kernel and sysfs report
lower voltages than are actually set in hardware (1300mV instead of 1800mV
for example) and in the worst case setting a voltage (e.g. 1800mV) will cause
an undervoltage condition (e.g. 1300mV).
Correct the behavior, taking into account SW1 doesn't support the HI bit,
and as such we need to ignore it.
While we are modifying these functions, fix and optimize the following;
* set_voltage_sel callback was using .reg instead of .vsel_reg - since
they were set to the same value it actually didn't break anything but
it would be semantically incorrect to use .reg in this case. We now use
.vsel_reg and be consistent.
* vsel_shift is always 0 for every SWx regulator, and constantly shifting
and masking off the bottom few bits is time consuming and makes the
code very hard to read - optimize this out.
* get_voltage_sel uses the variable "val" and set_voltage_sel uses the
variable "selector" (and reg_value). Introduce the variable "selector"
to get_voltage_sel such that it makes more sense and allow some leaner
code in light of the modifications in this patch. Add better exposure
to the debug print so the register value AND the selector are printed as
this will adequately show the HI bit in the register.
* correct a comment in probe which is doing a version check. Magic
values are awful but for once instance, a comment does just as
good a job as something symbolic.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree based initialization support for
TI's tps6507x regulators.
Add device tree binding document for TI's tps6507x
using datasheet:
http://www.ti.com/lit/ds/symlink/tps65070.pdf
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use &pdev->dev rather than iodev->dev for dev_err(), dev_warn() and dev_info().
Use &pdev->dev rather than iodev->dev for devm_kzalloc() and
of_get_regulator_init_data(), this fixes memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use &pdev->dev rather than iodev->dev for dev_err().
Use &pdev->dev rather than iodev->dev for devm_kzalloc() and
of_regulator_match(), this fixes memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dev parameter is the device requesting the data.
In this case it should be &pdev->dev rather than pdev->dev.parent.
The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(),
which means this fixes a memory leak because the memory is allocated every time
probe() is called, thus it should be freed when this driver is unloaded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct value for minimal voltage for ldo10 output is 950000 uV. This
patch fixes the typo introduced by patch adf6178ad5
("regulator: max8998: Use uV in voltage_map_desc"), what solves broken
probe of max8998 in v3.8-rc4.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_register() does not return NULL, it returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Building for the snowball board, I ran into this compile failure:
CC drivers/regulator/dbx500-prcmu.o
arm-test.git/drivers/regulator/dbx500-prcmu.c:119:11: error: 'THIS_MODULE' undeclared here (not in a function)
make[3]: *** [drivers/regulator/dbx500-prcmu.o] Error 1
make[2]: *** [drivers/regulator] Error 2
Commit 38e968380 "regulators/db8500: split off shared dbx500 code"
separated out the dbx500 code but did not copy over the required include
to linux/module.h.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dev parameter is the device requesting the data.
In this case it should be &pdev->dev rather than pdev->dev.parent.
The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(),
which means this fixes a memory leak because the memory is allocated every time
probe() is called, thus it should be freed when this driver is unloaded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan<ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dev parameter is the device requestiong the data.
In this case it should be &pdev->dev rather than pdev->dev.parent.
The dev parameter is used to call devm_kzalloc in of_get_regulator_init_data(),
which means this fixes a memory leak because the memory is allocated every time
probe() is called, thus it should be freed when this driver is unloaded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We already have enum lp8755_bucks in lp8755.h, so it looks pointless adding
enum bucks in lp8755.c.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It looks pointless to pass max_vol to s5m8767_convert_voltage_to_sel().
Compare selected voltage to desc->max is enough to ensure selected voltage
is in supported range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The vout address for buck[1|2] can be easily calculated,
thus remote these arrays.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we are in non-bypass mode then the SYSCLK is required for full charge
pump operation, otherwise we will fall back to bypass mode. Use the DAPM
context exposed by the ASoC driver to manage this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver use id as array index, thus add bounder checking for id.
This patch fixes below build warning:
drivers/regulator/lp8788-buck.c: In function 'lp8788_buck_probe':
drivers/regulator/lp8788-buck.c:490:8: warning: array subscript is above array bounds [-Warray-bounds]
drivers/regulator/lp8788-buck.c:489:63: warning: array subscript is above array bounds [-Warray-bounds]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DIV_ROUND_UP to prevent truncation by integer division issue.
This ensures we return enough delay time.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Integer division may truncate.
This happens when pdata->buckx_voltagex setting is not align with 1000 uV.
Thus use uV in voltage_map_desc, this ensures the selected voltage won't less
than pdata buckx_voltagex settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Current code does integer division (min_vol = min_uV / 1000) before pass
min_vol to max8997_get_voltage_proper_val().
So it is possible min_vol is truncated to a smaller value.
For example, if the request min_uV is 800900 for ldo.
min_vol = 800900 / 1000 = 800 (mV)
Then max8997_get_voltage_proper_val returns 800 mV for this case which is lower
than the requested voltage.
Use uV rather than mV in voltage_map_desc to prevent truncation by integer
division.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
regulator_list_voltage_table() returns -EINVAL if selector >= n_voltages.
Thus we don't need to check if reg is greater than LP3972_BUCK_VOL_MAX_IDX in
lp3972_[ldo|dcdc]_get_voltage_sel.
LP3972_BUCK_VOL_MIN_IDX and LP3972_BUCK_VOL_MAX_IDX are not used, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet, it has 9 multi-phase mode from 0 to 8 and it takes
4 bits in the register.
The mask for pchip->mphase should be 0x0F.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's safe to pass NULL argument to regulator_unregister(), so we can remove
the NULL checking before calling regulator_unregister().
However pass a ERR_PTR to regulator_unregister() is wrong, so we need to
explicitly set "pchip->rdev[buck_num] = NULL" before goto err_buck.
This patch also includes below cleanups:
Show correct regulator id in dev_err.
Remove __devexit_p.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ldo->en_pin is set iff the regulator is enabled by external pin.
This patch sets ldo->en_pin to NULL if lp8788_gpio_request_ldo_en() fails, then
we can use it to determinate if the regulator is controlled by external pin or
register.
lp8788_get_ldo_enable_mode(), lp8788_ldo_ctrl_by_extern_pin() and
lp8788_ldo_is_enabled_by_extern_pin() functions are not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator_register() does not return 0 on success, fix the comment.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use 'platform_device' rather than i2c client device node.
Argument is added in lp8788_config_ldo_enable_mode().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp8788-ldo is a platform driver of lp8788-mfd.
The platform device is allocated when mfd_add_devices() is called
in lp8788-mfd.
On the other hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case of
resource managed mem alloc, registering regulators and device kernel messages.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove space before semicolon in for-loop.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use 'platform_device' rather than i2c client device node.
Arguments are added in lp8788_init_dvs() and lp8788_dvs_gpio_request().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp8788-buck is a platform driver of lp8788-mfd.
The platform device is allocated when mfd_add_devices() is called
in lp8788-mfd.
On the other hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case of
resource managed mem alloc, registering a regulator and device kernel message.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
max8997_set_voltage_ldobuck_time_sel() returns 0 for all LDOs.
Thus remove set_voltage_time_sel setting for max8997_ldo_ops.
max8997_set_voltage_ldobuck_time_sel() is only used for max8997_buck_ops now,
rename it to max8997_set_voltage_buck_time_sel().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DT support for the TI TPS51632. Add device binding document also.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All TPS51632 registers are not readable/writable and
non-volatiles.
Add property of the registers whether it is readable/writable
or volatile for regmap framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
BUCK2 has the update_bit setting, but current code does not set update_bit
in pm8607_set_voltage_sel.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some DVM regulators needs to update apply_bit after setting vsel_reg to
initiate voltage change on the output. This patch adds apply_reg and
apply_bit to struct regulator_desc and update
regulator_set_voltage_sel_regmap() to set apply_bit of apply_reg when
apply_bit is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is for new lp8755 regulator dirver and
several unsed variables were deleted and then test was done.
LP8755 :
The LP8755 is a high performance power management unit.It contains
six step-down DC-DC converters which can can be filexibly bundled
together in multiphase converters as required by application.
www.ti.com
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Regulator drivers with continuous_voltage_range flag set allows not setting
n_voltages. Thus if continuous_voltage_range is set, check the constraint range
instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_list_voltage_table() returns -EINVAL if selector >= n_voltages.
Thus we don't need to check if reg is greater than BUCK_TARGET_VOL_MAX_IDX in
lp3971_dcdc_get_voltage_sel.
BUCK_TARGET_VOL_MIN_IDX and BUCK_TARGET_VOL_MAX_IDX are not used, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The function sec_reg_read invokes regmap_read which expects unsigned int *
as the destination address. The existing driver is passing address of local
variable "val" which is u8. This causes the stack corruption and following
dump is observed during probe.
Hence change "val" from u8 to unsigned int.
Unable to handle kernel paging request at virtual address 02410020
pgd = c0004000
[02410020] *pgd=00000000
Internal error: Oops: 80000005 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.6.0-00696-g98a28b18-dirty #27)
PC is at 0x2410020
LR is at _regulator_get_voltage+0x3c/0x70
pc : [<02410020>] lr : [<c02395d4>] psr: 20000013
sp : cf839b68 ip : 00000000 fp : cf92d410
r10: 0000cfd0 r9 : c06d9878 r8 : 0000f0a0
r7 : cf839b70 r6 : cf92d400 r5 : 00000011 r4 : cf000000
r3 : 02410020 r2 : 00000000 r1 : 00000048 r0 : cf000000
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
...........................
.................................
[<c02395d4>] (_regulator_get_voltage+0x3c/0x70) from [<c023ad80>] (print_constraints+0x50/0x36c)
[<c023ad80>] (print_constraints+0x50/0x36c) from [<c023e504>] (set_machine_constraints+0xe8/0x2b0)
[<c023e504>] (set_machine_constraints+0xe8/0x2b0) from [<c023e9c8>] (regulator_register+0x2fc/0x604)
[<c023e9c8>] (regulator_register+0x2fc/0x604) from [<c049d628>] (s5m8767_pmic_probe+0x688/0x718)
[<c049d628>] (s5m8767_pmic_probe+0x688/0x718) from [<c029915c>] (platform_drv_probe+0x18/0x1c)
[<c029915c>] (platform_drv_probe+0x18/0x1c) from [<c0297dd0>] (really_probe+0x68/0x1f4)
[<c0297dd0>] (really_probe+0x68/0x1f4) from [<c0298070>] (driver_probe_device+0x30/0x48)
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Having a linear_min_sel setting means the first linear_min_sel selectors are
invalid. We need to subtract linear_min_sel when use n_voltages to determinate
if regulator can change voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies the DVS register read function to select correct DVS1
register. This change is required because the GPIO select pin is 000 in
unintialized state and hence selects the DVS1 register.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If it's possible for gpio_set_value to sleep, we should be using
the *_cansleep call instead. This patch fixes multiple warnings
from gpiolib.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The cond-statement of this particular for() loop will always be
true as long as at least one voltage-shifting GPIO is present.
If it wasn't for the break below, we'd be stuck in a forever loop.
This patch inserts the correct cond-statement into the statement.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call regulator_[get|set]_voltage_sel_regmap instead of open code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ying-Chun Liu <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
By setting linear_min_sel to anatop_reg->min_bit_val, we can avoid
adjust the anatop_reg->min_bit_val offset in [set|get]_voltage_sel.
With this chance we can refactor this driver to use
regulator_[get|set]_voltage_sel_regmap.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Ying-Chun Liu <paulliu@debian.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is required since commit f7df20ec32
"regulator: core: Use list_voltage() to read single voltage regulators",
otherwise _regulator_get_voltage returns rdev->desc->ops->list_voltage(rdev, 0).
The Maxim 1586 controls V3 and V6 voltages, but offers no way of reading back
the set up value. Thus this patch caches the setting when setting new voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is only one user calling _rdev_to_offset() function.
Remove _rdev_to_offset() makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simply use devm_gpio_request_one() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To clear the mask bit, setting data argument to be 0 with proper mask setting
for lp8788_update_bits. We don't need the var array here.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use of_match_ptr and add ifdef CONFIG_OF guard for regulator_gpio_of_match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
The linear mapping is start from selector 6.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If pdata->base_voltage_uV is missing or the settings of pdata->base_voltage_uV
and pdata->max_voltage_uV are out of range, TPS51632_VOLT_VSEL macro
returns wrong vsel.
Thus add checking [base|max]_voltage_uV pdata settings in probe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DIV_ROUND_UP to ensure selected voltage won't less than min_uV due to
integer truncation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be converted to use linear_min_sel and
regulator_[map|list]_voltage_linear.
Below shows the equation (from Datasheet) for each LDOs.
For AUTOOUT:
VO(prog) = 0.625 + auto_out x 0.025 V; e.g.
(00000000 to 00101110: reserved)
00101111: 1.8 V (min)
01010011: 2.7 V
01101010: 3.275 V
01101011: 3.300 V
01101100: 3.325 V
01111111 : 3.800 V (max)
The linear mapping start from 0x2f selector.
Thus we convert this equation to:
VO(prog) = 1.8 + (selector - linear_min_sel) x 0.025 V
(min_uV = 1800000, uV_step = 25000, linear_min_sel = 0x2f)
For DOWNxOUT:
VO(prog) = 0.625 + downx_out x 0.025 V; e.g.
00000000 : 0.625 V (min)
00010111 : 1.200 V
00101111 : 1.800 V
01011111 : 3.000 V (max)
For xLDOOUT:
VO(prog) = 0.9 + xldo_out x 0.1 V; e.g.
00000: 0.9 V
00001: 1.0 V
11000 : 3.3 V
11011 : 3.6 V
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some Arizona devices such as the WM5102 can use DVFS on their digital core,
for these devices allow the voltage range to vary in the default setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Below equation means the "voltage" is the "smallest" voltage within specific
range.
ret = DIV_ROUND_UP(min - bottom) / step;
voltage = ret * step + bottom;
If we do try 1 down when (voltage > max), new voltage is then less than min
voltage. Which means the new voltage is not in the requested voltage range.
This patch also includes below cleanups:
- Use DIV_ROUND_UP
- rename variable 'ret' to 'sel' for better readability because as3711_sel_check
returns the selector.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Below cases are supposed to be valid:
min_uV == max_uV == info->max_uV
min_uV == max_uV == rdev->desc->min_uV
Don't return -EINVAL for above cases.
This patch also includes below cleanups:
- Use rdev_get_drvdata(rdev) instead of rdev->reg_data.
- Remove unnecessary WARN_ON, it looks pointless.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fix the abnormal ramp delay setting.
The shift operation was wrong.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Checking da9052_current_limits[row][i] <= max_uA is not enough, it is possible
da9052_current_limits[row][i] may less than the requested min_uA.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
This issue was reported by Heiko Stuebner for gpio-regulator driver [1],
and the conclusion is to select the max current for current regulators [2].
[1] https://lkml.org/lkml/2012/8/5/162
[2] https://lkml.org/lkml/2012/8/6/183
This patch also ensures da9055_buck_set_current_limit return -EINVAL when the
supported current limit does not meet the request range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When building the driver in debug mode, it generates
warning as
drivers/regulator/tps6586x-regulator.c: In function 'tps6586x_regulator_probe':
drivers/regulator/tps6586x-regulator.c:392:9: warning: 'id' is used uninitialized in this function [-Wuninitialized]
Fix this warning.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When tps->enable_pwm_dvfs is true, write to TPS51632_VOLTAGE_BASE_REG rather
than TPS51632_VOLTAGE_SELECT_REG.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case the gpio based volatage selection mode is not used for either of
buck 1/2/5, then only the BUCKxDVS1 register need to be programmed. So
determine whether dvs mode is used and limit the loop count appropriately.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The BUCKxDVSx register programming is now moved prior to setting up of the
gpio based dvs mode. This will ensure that all the BUCKxDVSx registers
are programmed with appropriate voltage values before the gpio based dvs
mode is selected for buck1/2/5.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be built as a module, add MODULE_ALIAS for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If external control is enabled then do not provide regulator
enable/disable apis.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports the 4 DCDC and 8 LDO regulators on the AS3711 PMIC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement list_voltage for fixed regulators, otherwise
regulator_is_supported_voltage() returns 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch includes below cleanups:
- Fix typo in comment
- Fix showing wrong register in dev_err
- Remove unnecessary rinfo variable
- Add TPS80032 to MODULE_DESCRIPTION
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements map_voltage and list_voltage callbacks to properly handle
the case voltage range that doesn't start with 0 offset.
Now we adjust the selector in map_voltage() before calling set_voltage_sel().
And return 0 in list_voltage() for invalid selectors.
With above change, we can remove da9055_regulator_set_voltage_bits function.
One tricky part is that we need adding voffset to n_voltages.
Although for the cases "selector < voffset" are invalid, we need add voffset to
n_voltage so regulator_list_voltage() won't fail while checking the boundary for
selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.
Add regulator driver for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check pdata->gpio_rsel && pdata->gpio_rsel[id] for the case GPI pin is muxed
with regulator to select the regulator register set A/B for voltage ramping.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pefix "TPS80031" is added on all defines of tps80031 header
to avoid conflict with other header definitions.
Update the regualtor driver of tps80031 to use the same name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the Regulator patch for the DA9055 PMIC and has got dependency on
the DA9055 MFD core.
This patch support all of the DA9055 regulators. The output voltages are
fully programmable through I2C interface only. The platform data with regulation
constraints is passed down from the board to the regulator.
This patch is functionaly tested on SMDK6410 board. DA9055 Evaluation board
was connected to the SMDK6410 board.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Moving regulator node parsing to regulator driver in place
of parsing it on mfd driver.
The motivation for this change are:
- MFD core driver should not depends on regulator and able
to instantiate device without regulator.
- The API for matching regulators are in regulator core and
it is good that regulator driver only calls this API.
- Regulator specific support should be in regulator driver only
to ease any enhancement/modification for regulators.
- The regulator driver is now registered as mfd sub device and
all regulator registration is done from single probe call.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
A selection of voltage or current values (AKA states) should always
be specified when using a GPIO regulator. If there are no switchable
states then the fixed regulators should be used instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Need initilize of_node in regulator config when register regulator,
otherwise regulator driver think it is no-dt device.
in regulator_dev_lookup
list_for_each_entry(r, ®ulator_list, list)
if (r->dev.parent &&
node == r->dev.of_node)
return r
r->dev.of_noe will be zero if miss config in cfg.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for Texas Instrument TPS80031/TPS80032 device.
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. It has 5 configurable step-down
converters, 11 general purpose LDOs, VBUS generator and digital
output to control regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the gpio_request_one() fails, or returns EPROBE_DEFER, the
regulator must be device_unregister()ed. When this is not done,
there are WARNING: from sysfs:
WARNING: at fs/sysfs/file.c:343 sysfs_open_file+0x238/0x268()
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a sparse warning. Since max77686_enable() is a callback,so it
should be static.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here we provide the GPIO Regulator driver with Device Tree capability, so
that when a platform is booting with DT instead of platform data we can
still make full use of it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS65090's DCDC output can also be enable/disable through the
external digital input signal. Add support for enable/disable
either through register access via I2C or through external
control inputs. The external control inputs can be driven through
GPIOs also and hence adding support for passing the GPIO number.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TPS65090 supports the two LDOs, LDO1 and LDO2. These are
always ON regulators. The output on these LDOs are available
once the input voltage available for these LDOs.
Add support for these LDOs regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make the names proper and more appropriate:
Rename the driver name from tps65090-regulator to tps65090-pmic.
Rename the regulators from TPS65090_ID_* to TPS65090_REGULATOR_*
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MFD driver registers the regulator driver once per device and
hence it is require to register all regulators in single probe
call.
Following are details of changes done to achieve this:
- Move the regulator enums to mfd header and remove the
tps65090-regulator.h as it does not contain more info.
- Add max regulator and register all regulators even if there
is no regulator init data from platform.
- Convert regulator init data to pointer type in platform data.
- Add input supply name in regulator desc to provide input supply.
- Separate desc information from driver information.
- Disable external control bit to have control through register write.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix BUG_ON() error if tps65910 VRTC regulator is used with out
rdev->desc->volt_table data. Recent changes in regulator core driver
which add support for "regulator_list_voltage_table" have BUG_ON() if
regulator descriptor do not voltage table information. This patch adds
the voltage table information to fix the issue.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements set_suspend_disable callback for BUCKs which
support only switch ON/OFF modes during system suspend state, and
set_suspend_mode callbacks for LDOs which also suport Low power mode and
switch ON/OFF modes.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds basic support to take care of opmode(if any) which can be set by
set_suspend_[disable/mode] callbacks.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implementation of the regulator framework driver for the
Versatile Express voltage control. Devices without
voltage constraints (ie. "regulator-[min|max]-microvolt"
properties in the DT node) are treated as fixed (or rather
read-only) regulators.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulators can set any voltage within the constraints range,
not being limited to specified operating points.
This patch makes it possible to describe such regulator and makes
the regulator_is_supported_voltage() function behave correctly.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS51632 is a driverless step down controller with
serial control. Advanced features such as D-Cap+
architecture with overlapping pulse support and OSR
overshoot reduction provide fast transient response,
lowest output capacitance and high efficiency.
The TPS51632 supports both I2C and DVFS interfaces
(through PWM) for dynamic control of the output voltage
and current monitor telemetry.
Add regulator driver for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
When the bindings for the TPS6586x regulator were being proposed, I
asserted that DT node naming rules for bus child nodes should also be
applied to nodes inside the TPS6586x regulator node itself. In other
words, that each node providing regulator init data should be named
after the type of object it represented ("regulator") and hence that
some other property was required to indicate which regulator the node
described ("regulator-compatible"). In turn this led to multiple nodes
having the same name, thus requiring node names to use a unit address
to make them unique, thus requiring reg properties within the nodes and
However, subsequent discussion indicates that the rules I was asserting
only applies to standardized bus nodes, and within a device's own node,
the binding can basically do anything sane that it wants.
Hence, this change deprecates the register-compatible property, and
instead uses node names to replace this functionality. This greatly
simplifies the device tree content, making them smaller and more legible.
The code is changed such that old device trees continue to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DT support to palmas regulator. This involved a little change to
the platform data structure. Regulator information can now come from
platform data or DT.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since PREG regulator is the only one regulator in 88PM8606, and other
regulators are in 88PM8607. Checking resource as identifying regulator
is not a good way. We can use NULL resource to indentify PREG regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator support for 88pm860x regulator driver.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove array in parent's platform data. Use struct regulator_init_data
as regulator device's platform data directly. So a lot of pdata are
added into parent's platform data. And voltage out register offset
is used as IORESOURCE_REG to distinguish different regualtor devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using syscon to access anatop register.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to initialize the
watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device addition
API in order to prevent silent and potentially harmful remapping behaviour
changes for drivers supporting non-DT platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nP/y
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since IORESOURCE_IO is changed to IORESOURCE_REG in 88pm860x driver,
update self-defined IORESOURCE_IO resource to register offset that
is IORESOURCE_REG in regulator driver. And split regulator platform
data array into scattered platform data.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was originally written by Russell King who unfortunately found
himself unable to take the patch futher.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The max voltage will be bounded by min_uV, uV_step and n_voltages, so
remove it to avoid confusing.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Doing so generates a warning as the first field is a pointer but we use
0 to initalize it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.
Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.
This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
This driver supports Fairchild FAN53555 Digitally Programmable
TinyBuck Regulator. The FAN53555 is a step-down switching voltage
regulator that delivers a digitally programmable output from an
input voltage supply of 2.5V to 5.5V. The output voltage is
programmed through an I2C interface.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the device doesn't have a regmap specified by the driver and we can't
find one on the device itself try its parent, providing a useful defualt
for many MFDs.
[Rewrite commit message -- broonie]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Users (especially framework code) may end up passing in a zero deferral
time depending on runtime conditions or configuration. If they do then
just call regulator_disable() directly to save scheduling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a regulator only supports a single voltage list_voltage() can be used
to report what that voltage is so add this as one of the criteria for
creating the microvolts file in sysfs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.
[swarren: Instantiate the sys regulator from board-harmony-power.c to
avoid regression.]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp872x_check_dvs_validity() is used for checking DVS platform data.
If the DVS platform data is not defined, return as error code.
Now, this is unnecessary because the default DVS mode is set in this case.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp872x_set_dvs() is used for changing the DVS pin state.
This function works only when the DVS platform data is defined.
So don't assume that DVS data is always valid.
In case the platform data is not defined, the DVS data is set to NULL
for skipping the DVS pin control.
DVS selection and GPIO pin number are used for the LP872x DVS pin control.
For better readability, DVS selection argument is added in lp872x_set_dvs().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The platform specific configuration(general_config) is optional.
However, the DVS settings should be configured explicitly while
loading the driver.
This patch enables configuring the default DVS mode even though
the platform data is not defined.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp872x driver has the DVS platform data which select the register address
of the BUCK voltage.
This patch enables updating the default DVS mode when the DVS platform data
is not defined.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch enables registering the regulator driver even though
the regulator_init_data is not defined in the platform side.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be built as a module, add MODULE_ALIAS for it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regulator is not used by a board, it's quite legitimate not to
provide platform data or a device tree node to configure it (i.e.
regulator_init_data). In that case, during MAX8907 regulator's
probe(), the idata variable will be NULL for that regulator. Prevent
dereferincing it.
If the MBATT regulator's init_data is not specified, or no name was
specified in the constraints, the regulator will be named based on
the regulator descriptor, so initialize mbatt_rail_name from there.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This encodes the voltage shifts (the number of bits to shift
the register to get to the selector) into the regulator info.
We have several new variants of the AB8500 so this varies a
lot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following:
CC [M] drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_probe':
drivers/regulator/max8907-regulator.c:297:12: error: 'max8907_matches' undeclared (first use in this function)
by removing direct references to max8907_matches[], which only exists when
CONFIG_OF is defined.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add missing platform_get_drvdata() call in max8907_regulator_remove(), this
fixes below build warning:
CC [M] drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_remove':
drivers/regulator/max8907-regulator.c:353:23: warning: 'pmic' is used uninitialized in this function [-Wuninitialized]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For linear voltage mapping, the n_voltages is (max - min) / step + 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes this build error:
drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1229:3: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
Also added string.h for kmemdup().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Allowed probing from device tree.
* Reworked the regulator driver to be represented as a single device that
provides multiple regulators, rather than as a device per regulator.
* Replaced many regulator ops with standard functions.
* Added ability to specify supplies for each regulator.
* Removed the WLED regulator. If/when we expose this in the driver, it
should be a backlight object not a regulator object.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I currently carry the series to make of_device_id->data const in the
arm-soc tree, which fixes a number of issues, but leaves one new
compiler warning about the twl-regulator driver:
drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1130:8: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]
drivers/regulator/twl-regulator.c:1139:9: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]
The warning indicates that the driver takes a static table with
initialization data for each regulator, modifies the data in place
and passes a pointer to that structure to the regulator_register
function. This is probably ok because a system contains only one
instance of each regulator, but it's still bad style because any
driver should be written to support multiple instances of the same
hardware.
This patch changes the code to dynamically allocate the memory
we pass to the regulator core so the table can be constant.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MAX77686_REGULATORS is known in compile time.
Use array to save pointer to rdev makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin