Enforce correct device sequencing when configuring a new
audio route when there is an existing active audio route(s).
This patch fixed recording noise issue while playback is active.
We have some registers which require the device to be in full shutdown
or to enter full shutdown before the register settings will take effect.
Currently the driver is not shutting down the device when a new audio
route is created. If a new audio route is made active while there is
already an active audio route, then the required register sequencing is
violated. A hardware shutdown toggle when creating a new audio route
corrects the sequencing error. The device must remain in hardware
shutdown for 40ms to allow the internal hardware core to fully shutdown.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Anish Kumar <anish.kumar@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In addtion expand the table to handle other values of sysclk. Instead
of making the table 3D, expand it to a more descriptive struct. The
divisors are specified in Table 19 of the 98090 data sheet version
0p94.
The dmic frequency was previously assumed. Instead make it explicit
and configurable through device tree. This now handles independently
set pclk and dmic frequency.
Based on downstream work by Ralph Birt.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no other use for extmic_mux than setting it to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct max98090_priv member irq is now used only locally in
max98090_i2c_probe() and can be removed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All MAX98090 input clocks MCLK, LRCLK and BCLK must be running and stable
before powering on the codec in slave mode. Otherwise the PLL may not lock
to LRCLK causing silence in playback and capture. How often that happens is
somewhat hardware and clock configuration specific.
Now if wanting to follow strictly this clocks must be active before
powering the codec on requirement we should have a notification from DAI
driver to codec driver when clocks are activated and take codec out of
shutdown only after that. Plus take care of possible active bypass paths.
However, when PLL unlock occurs, MAX98090 asserts the PLL Unlock Flag which
can be configured as an IRQ source. This allows to workaround around the
issue by toggling the codec power shortly in case of PLL lock failure.
In order to prevent needlessly toggling codec power in case of short PLL
unlocks at the beginning of stream this patch implements delayed activation
for PLL unlock interrupt. Then workaround is run only when the PLL doesn't
lock at all.
Power toggling workaround for PLL unlock comes originally from
Liam Girdwood <liam.r.girdwood@linux.intel.com> and delayed activation from
me.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If master clock is provided through device tree, then update
the master clock frequency during set_sysclk.
Documentation has been updated to reflect the change.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
BCL is being configured in two places producing a warning message.
Make sure we only configure BCLK once and when we are master.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver assigns a value to the control_data field of the driver's state
struct, but never reads it again. Which means it is unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Source files shouldn't have the executable bit set.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch completes the replacement of the existing max98090 driver,
by installing a more complete driver.
Signed-off-by: Jerry Wong <jerry.wong@maximintegrated.com>
Tested-by: Matthew Mowdy <matthew.mowdy@maximintegrated.com>
Reviewed-by: Ralph Birt <ralph.birt@maximintegrated.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kuninori Morimoto