Unprivileged functions (such as VFs) may set their MTU by use of the
'control' field of MC_CMD_SET_MAC_EXT, as used in efx_mcdi_set_mtu().
If calling efx_ef10_mac_reconfigure() from efx_change_mtu(), and the
NIC supports the above (SET_MAC_ENHANCED capability), use it rather
than efx_mcdi_set_mac().
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable act is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: simplify endpoint programming
Add tests to functions so they don't update undefined endpoint
registers, rather than requiring the caller to avoid calling them.
Move the call to a workaround function required when suspending
inside the function that puts an endpoint into suspend mode. This
requires moving a few functions (which are otherwise unchanged).
Then simplify ipa_endpoint_program() to call essentially all
endpoint register update functions unconditionally.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Have functions that write endpoint configuration registers return
immediately if they are not valid for the direction of transfer for
the endpoint. This allows most of the calls in ipa_endpoint_program()
to be made unconditionally. Reorder the register writes to match
the order of their definition (based on offset).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 4.0+ does not support endpoint suspend. Put a test at
the top of ipa_endpoint_program_suspend() that returns immediately
if suspend is not supported rather than making that check in the caller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 3.5.1 has a hardware quirk that requires special
handling if an RX endpoint is suspended while aggregation is active.
This handling is implemented by ipa_endpoint_suspend_aggr().
Have ipa_endpoint_program_suspend() be responsible for calling
ipa_endpoint_suspend_aggr() if suspend mode is being enabled on
an endpoint. If the endpoint does not support aggregation, or if
aggregation isn't active, this call will continue to have no effect.
Move the definition of ipa_endpoint_suspend_aggr() up in the file so
its definition precedes the new earlier reference to it. This
requires ipa_endpoint_aggr_active() and ipa_endpoint_force_close()
to be moved as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA version 4.2 has a hardware quirk that affects endpoint delay
mode, so it isn't used there. Isolate the test that avoids using
delay mode for that version inside ipa_endpoint_program_delay(),
rather than making that check in the caller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain configurations without power management support, the
following warnings happen:
drivers/net/ethernet/mellanox/mlx4/main.c:4388:12:
warning: 'mlx4_resume' defined but not used [-Wunused-function]
4388 | static int mlx4_resume(struct device *dev_d)
| ^~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx4/main.c:4373:12: warning:
'mlx4_suspend' defined but not used [-Wunused-function]
4373 | static int mlx4_suspend(struct device *dev_d)
| ^~~~~~~~~~~~
Mark these functions as __maybe_unused to make it clear to the
compiler that this is going to happen based on the configuration,
which is the standard for these types of functions.
Fixes: 0e3e206a3e ("mlx4: use generic power management")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain configurations without power management support, gcc report
the following warning:
drivers/net/ethernet/micrel/ksz884x.c:7182:12: warning:
'pcidev_suspend' defined but not used [-Wunused-function]
7182 | static int pcidev_suspend(struct device *dev_d)
| ^~~~~~~~~~~~~~
Mark pcidev_suspend() as __maybe_unused to make it clear.
Fixes: 64120615d1 ("ksz884x: use generic power management")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Beznea says:
====================
net: macb: few code cleanups
Patches in this series cleanup a bit macb code.
Changes in v2:
- in patch 2/4 use hweight32() instead of hweight_long()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove is_udp variable that is used in only one place and use
ip_hdr(skb)->protocol == IPPROTO_UDP check instead.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not initialize queue variable. It is already initialized in for loops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hweight32() to count set bits in queue_mask.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 0 of queue_mask is set at the beginning of
macb_probe_queues() function. Do not set it again after reading
DGFG6 but instead use "|=" operator.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
bridge: mrp: Add support for getting the status
This patch series extends the MRP netlink interface to allow the userspace
daemon to get the status of the MRP instances in the kernel.
v3:
- remove misleading comment
- fix to use correctly the RCU
v2:
- fix sparse warnings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the function br_fill_ifinfo to return also the MRP
status for each instance on a bridge. It also adds a new filter
RTEXT_FILTER_MRP to return the MRP status only when this is set, not to
interfer with the vlans. The MRP status is return only on the bridge
interfaces.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the function br_mrp_fill_info which populates the MRP attributes
regarding the status of each MRP instance.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MRP attribute IFLA_BRIDGE_MRP_INFO to allow the userspace to get the
current state of the MRP instances. This is a nested attribute that
contains other attributes like, ring id, index of primary and secondary
port, priority, ring state, ring role.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is common for networking tests creating its netns and making its own
setting under this new netns (e.g. changing tcp sysctl). If the test
forgot to restore to the original netns, it would affect the
result of other tests.
This patch saves the original netns at the beginning and then restores it
after every test. Since the restore "setns()" is not expensive, it does it
on all tests without tracking if a test has created a new netns or not.
The new restore_netns() could also be done in test__end_subtest() such
that each subtest will get an automatic netns reset. However,
the individual test would lose flexibility to have total control
on netns for its own subtests. In some cases, forcing a test to do
unnecessary netns re-configure for each subtest is time consuming.
e.g. In my vm, forcing netns re-configure on each subtest in sk_assign.c
increased the runtime from 1s to 8s. On top of that, test_progs.c
is also doing per-test (instead of per-subtest) cleanup for cgroup.
Thus, this patch also does per-test restore_netns(). The only existing
per-subtest cleanup is reset_affinity() and no test is depending on this.
Thus, it is removed from test__end_subtest() to give a consistent
expectation to the individual tests. test_progs.c only ensures
any affinity/netns/cgroup change made by an earlier test does not
affect the following tests.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200702004858.2103728-1-kafai@fb.com
This patch makes a few changes to the network_helpers.c
1) Enforce SO_RCVTIMEO and SO_SNDTIMEO
This patch enforces timeout to the network fds through setsockopt
SO_RCVTIMEO and SO_SNDTIMEO.
It will remove the need for SOCK_NONBLOCK that requires a more demanding
timeout logic with epoll/select, e.g. epoll_create, epoll_ctrl, and
then epoll_wait for timeout.
That removes the need for connect_wait() from the
cgroup_skb_sk_lookup.c. The needed change is made in
cgroup_skb_sk_lookup.c.
2) start_server():
Add optional addr_str and port to start_server().
That removes the need of the start_server_with_port(). The caller
can pass addr_str==NULL and/or port==0.
I have a future tcp-hdr-opt test that will pass a non-NULL addr_str
and it is in general useful for other future tests.
"int timeout_ms" is also added to control the timeout
on the "accept(listen_fd)".
3) connect_to_fd(): Fully use the server_fd.
The server sock address has already been obtained from
getsockname(server_fd). The sockaddr includes the family,
so the "int family" arg is redundant.
Since the server address is obtained from server_fd, there
is little reason not to get the server's socket type from the
server_fd also. getsockopt(server_fd) can be used to do that,
so "int type" arg is also removed.
"int timeout_ms" is added.
4) connect_fd_to_fd():
"int timeout_ms" is added.
Some code is also refactored to connect_fd_to_addr() which is
shared with connect_to_fd().
5) Preserve errno:
Some callers need to check errno, e.g. cgroup_skb_sk_lookup.c.
Make changes to do it more consistently in save_errno_close()
and log_err().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20200702004852.2103003-1-kafai@fb.com
Florian Westphal says:
====================
mptcp: add receive buffer auto-tuning
First patch extends the test script to allow for reproducible results.
Second patch adds receive auto-tuning. Its based on what TCP is doing,
only difference is that we use the largest RTT of any of the subflows
and that we will update all subflows with the new value.
Else, we get spurious packet drops because the mptcp work queue might
not be able to move packets from subflow socket to master socket
fast enough. Without the adjustment, TCP may drop the packets because
the subflow socket is over its rcvbuffer limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When mptcp is used, userspace doesn't read from the tcp (subflow)
socket but from the parent (mptcp) socket receive queue.
skbs are moved from the subflow socket to the mptcp rx queue either from
'data_ready' callback (if mptcp socket can be locked), a work queue, or
the socket receive function.
This means tcp_rcv_space_adjust() is never called and thus no receive
buffer size auto-tuning is done.
An earlier (not merged) patch added tcp_rcv_space_adjust() calls to the
function that moves skbs from subflow to mptcp socket.
While this enabled autotuning, it also meant tuning was done even if
userspace was reading the mptcp socket very slowly.
This adds mptcp_rcv_space_adjust() and calls it after userspace has
read data from the mptcp socket rx queue.
Its very similar to tcp_rcv_space_adjust, with two differences:
1. The rtt estimate is the largest one observed on a subflow
2. The rcvbuf size and window clamp of all subflows is adjusted
to the mptcp-level rcvbuf.
Otherwise, we get spurious drops at tcp (subflow) socket level if
the skbs are not moved to the mptcp socket fast enough.
Before:
time mptcp_connect.sh -t -f $((4*1024*1024)) -d 300 -l 0.01% -r 0 -e "" -m mmap
[..]
ns4 MPTCP -> ns3 (10.0.3.2:10108 ) MPTCP (duration 40823ms) [ OK ]
ns4 MPTCP -> ns3 (10.0.3.2:10109 ) TCP (duration 23119ms) [ OK ]
ns4 TCP -> ns3 (10.0.3.2:10110 ) MPTCP (duration 5421ms) [ OK ]
ns4 MPTCP -> ns3 (dead:beef:3::2:10111) MPTCP (duration 41446ms) [ OK ]
ns4 MPTCP -> ns3 (dead:beef:3::2:10112) TCP (duration 23427ms) [ OK ]
ns4 TCP -> ns3 (dead:beef:3::2:10113) MPTCP (duration 5426ms) [ OK ]
Time: 1396 seconds
After:
ns4 MPTCP -> ns3 (10.0.3.2:10108 ) MPTCP (duration 5417ms) [ OK ]
ns4 MPTCP -> ns3 (10.0.3.2:10109 ) TCP (duration 5427ms) [ OK ]
ns4 TCP -> ns3 (10.0.3.2:10110 ) MPTCP (duration 5422ms) [ OK ]
ns4 MPTCP -> ns3 (dead:beef:3::2:10111) MPTCP (duration 5415ms) [ OK ]
ns4 MPTCP -> ns3 (dead:beef:3::2:10112) TCP (duration 5422ms) [ OK ]
ns4 TCP -> ns3 (dead:beef:3::2:10113) MPTCP (duration 5423ms) [ OK ]
Time: 296 seconds
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The script generates two random files that are then sent via tcp and
mptcp connections.
In order to compare throughput over consecutive runs add an option
to provide the file size on the command line: "-f 128000".
Also add an option, -t, to enable tcp tests. This is useful to
compare throughput of mptcp connections and tcp connections.
Example: run tests with a 4mb file size, 300ms delay 0.01% loss,
default gso/tso/gro settings and with large write/blocking io:
mptcp_connect.sh -t -f $((4 * 1024 * 1024)) -d 300 -l 0.01% -r 0 -e "" -m mmap
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to fq_codel and the other qdiscs that can set as default,
fq_pie is also suitable for general use without explicit configuration,
which makes it a valid choice for this.
This is useful in situations where a painless out-of-the-box solution
for reducing bufferbloat is desired but fq_codel is not necessarily the
best choice. For example, fq_pie can be better for DASH streaming, but
there could be more cases where it's the better choice of the two simple
AQMs available in the kernel.
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2020-07-01
This series contains updates to all Intel drivers, but a majority of the
changes are to the i40e driver.
Jeff converts 'fall through' comments to the 'fallthrough;' keyword for
all Intel drivers. Removed unnecessary delay in the ixgbe ethtool
diagnostics test.
Arkadiusz implements Total Port Shutdown for i40e. This is the revised
patch based on Jakub's feedback from an earlier submission of this
patch, where additional code comments and description was needed to
describe the functionality.
Wei Yongjun fixes return error code for iavf_init_get_resources().
Magnus optimizes XDP code in i40e; starting with AF_XDP zero-copy
transmit completion path. Then by only executing a division when
necessary in the napi_poll data path. Move the check for transmit ring
full outside the send loop to increase performance.
Ciara add XDP ring statistics to i40e and the ability to dump these
statistics and descriptors.
Tony fixes reporting iavf statistics.
Radoslaw adds support for 2.5 and 5 Gbps by implementing the newer ethtool
ksettings API in ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-07-01
This series contains updates to the ice driver only.
Jacob implements a devlink region for device capabilities.
Bruce removes structs containing only one-element arrays that are either
unused or only used for indexing. Instead, use pointer arithmetic or
other indexing to access the elements. Converts "C struct hack"
variable-length types to the preferred C99 flexible array member.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the pre-C90-extension "C struct hack" method (using a single-
element array at the end of a structure for implementing variable-length
types) to the preferred use of C99 flexible array member.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are a number of structures that consist of a one-element array as the
only struct member. Some of those are unused so remove them. Others are
used to index into a buffer/array consisting of a variable number of a
different data or structure type. Those are unnecessary since we can use
simple pointer arithmetic or index directly into the buffer to access
individual elements of the buffer/array.
Additional code cleanups were done near areas affected by this change.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
At the moment, bonding xfrm crypto offload can only be set up if the bonding
module is loaded with active-backup mode already set. We need to be able to
make this work with bonds set to AB after the bonding driver has already
been loaded.
So what's done here is:
1) move #define BOND_XFRM_FEATURES to net/bonding.h so it can be used
by both bond_main.c and bond_options.c
2) set BOND_XFRM_FEATURES in bond_dev->hw_features universally, rather than
only when loading in AB mode
3) wire up xfrmdev_ops universally too
4) disable BOND_XFRM_FEATURES in bond_dev->features if not AB
5) exit early (non-AB case) from bond_ipsec_offload_ok, to prevent a
performance hit from traversing into the underlying drivers
5) toggle BOND_XFRM_FEATURES in bond_dev->wanted_features and call
netdev_change_features() from bond_option_mode_set()
In my local testing, I can change bonding modes back and forth on the fly,
have hardware offload work when I'm in AB, and see no performance penalty
to non-AB software encryption, despite having xfrm bits all wired up for
all modes now.
Fixes: 18cb261afd ("bonding: support hardware encryption offload to slaves")
Reported-by: Huy Nguyen <huyn@mellanox.com>
CC: Saeed Mahameed <saeedm@mellanox.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: netdev@vger.kernel.org
CC: intel-wired-lan@lists.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new devlink region used for capturing a snapshot of the device
capabilities buffer which is reported by the firmware over the AdminQ.
This information can useful in debugging driver and firmware
interactions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Alex Elder says:
====================
net: ipa: endpoint configuration updates
This series updates code that configures IPA endpoints. The changes
made mainly affect access to registers that are valid only for RX, or
only for TX endpoints.
The first three patches avoid writing endpoint registers if they are
not defined to be valid. The fourth patch slightly modifies the
parameters for the offset macros used for these endpoint registers,
to make it explicit when only some endpoints are valid.
The last patch just tweaks one line of code so it uses a convention
used everywhere else in the driver.
Version 2 of this series eliminates some of the "assert()" comments
that Jakub inquired about. The ones removed will actually go away
in an upcoming (not-yet-posted) patch series anyway.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The convention throughout the IPA driver is to directly use
single-bit field mask values, rather than using (for example)
u32_encode_bits() to set or clear them.
Fix the one place that doesn't follow that convention, which sets
HOL_BLOCK_EN_FMASK in ipa_endpoint_init_hol_block_enable().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A handful of registers are valid only for RX endpoints, and some
others are valid only for TX endpoints. For these endpoints, add
a comment above their defined offset macro that indicates the
endpoints to which they apply.
Extend the endpoint parameter naming convention as well, to make
these constraints more explicit.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_MODE endpoint configuration register is only valid for TX
endpoints. Rather than writing a zero to that register for RX
endpoints, avoid writing the register at all.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_HDR_METADATA_MASK endpoint configuration register is only
valid for RX endpoints. Rather than writing a zero to that register
for TX endpoints, avoid writing the register at all.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The INIT_HOL_BLOCK_EN and INIT_HOL_BLOCK_TIMER endpoint registers
are only valid for RX endpoints.
Have ipa_endpoint_modem_hol_block_clear_all() skip writing these
registers for TX endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: small improvements
This series contains two patches that improve the error output
that's reported when an error occurs while changing the state of a
GSI channel or event ring. The first ensures all such error
conditions report an error, and the second simplifies the messages a
little and ensures they are all consistent.
A third (independent) patch gets rid of an unused symbol in the
microcontroller code.
Version 2 fixes two alignment problems pointed out by checkpatch.pl,
as requested by Jakub Kicinski.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The microcontroller shared memory area is at the beginning of the
IPA resident memory. IPA_MEM_UC_OFFSET was defined as the offset
within that region where it's found, but it's 0, and it's never
actually used. Just get rid of the definition, and move some of the
description it had to be above the definition of the ipa_uc_mem_area
structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make minor updates to error messages reported in "gsi.c":
- Use local variables to reduce multi-line function calls
- Don't use parentheses in messages
- Do some slight rewording in a few cases
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check the state of an event ring or channel both before and after
any GSI command issued that will change that state. In most--but
not all--cases, if the state is something different than expected we
report an error message.
Add error messages where missing, so that all unexpected states
provide information about what went wrong. Drop the parentheses
around the state value shown in all cases.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: simple refactorizations
This series makes three small changes to some endpoint configuration
code. The first uses a constant to represent the frequency of an
internal clock used for timers in the IPA. The second modifies a
limit used so it matches Qualcomm's internal code. And the third
reworks a few lines of code, eliminating a multi-line function call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the "limit" local variable in ipa_endpoint_init_aggr() when
setting the aggregation size limit. Simple cleanup.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Halve the time limit used when aggregation is enabled on an RX
endpoint, to half a millisecond.
Use DIV_ROUND_CLOSEST() to compute the value that represents the
time period, to get better accuracy in the event the time limit is
not an even multiple of the granularity.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer used for aggregation makes use of an internal 32 KHz clock.
The granularity of the timer is programmed by a field whose value is
computed by ipa_aggr_granularity_val(). Redefine the way that value
is computed by using a new TIMER_FREQUENCY constant representing the
underlying clock frequency.
Add two BUILD_BUG_ON() calls to ensure the value used is valid.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov says:
====================
xen networking: add XDP support to xen-netfront
The first patch adds a new extra type to enable proper synchronization
between an RX request/response pair.
The second patch implements BFP interface for xen-netfront.
The third patch enables extra space for XDP processing.
v14:
- fixed compilation warnings
v13:
- fixed compilation due to previous rename
v12:
- xen-netback: rename netfront_xdp_headroom to xdp_headroom
v11:
- add the new headroom constant to netif.h
- xenbus_scanf check
- lock a bulk of puckets in xennet_xdp_xmit()
v10:
- add a new xen_netif_extra_info type to enable proper synchronization
between an RX request/response pair.
- order local variable declarations
v9:
- assign an xdp program before switching to Reconfiguring
- minor cleanups
- address checkpatch issues
v8:
- add PAGE_POOL config dependency
- keep the state of XDP processing in netfront_xdp_enabled
- fixed allocator type in xdp_rxq_info_reg_mem_model()
- minor cleanups in xen-netback
v7:
- use page_pool_dev_alloc_pages() on page allocation
- remove the leftover break statement from netback_changed
v6:
- added the missing SOB line
- fixed subject
v5:
- split netfront/netback changes
- added a sync point between backend/frontend on switching to XDP
- added pagepool API
v4:
- added verbose patch descriprion
- don't expose the XDP headroom offset to the domU guest
- add a modparam to netback to toggle XDP offset
- don't process jumbo frames for now
v3:
- added XDP_TX support (tested with xdping echoserver)
- added XDP_REDIRECT support (tested with modified xdp_redirect_kern)
- moved xdp negotiation to xen-netback
v2:
- avoid data copying while passing to XDP
- tell xen-netback that we need the headroom space
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the patch basically adds the offset adjustment and netfront
state reading to make XDP work on netfront side.
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds a basic XDP processing to xen-netfront driver.
We ran an XDP program for an RX response received from netback
driver. Also we request xen-netback to adjust data offset for
bpf_xdp_adjust_head() header space for custom headers.
synchronization between frontend and backend parts is done
by using xenbus state switching:
Reconfiguring -> Reconfigured- > Connected
UDP packets drop rate using xdp program is around 310 kpps
using ./pktgen_sample04_many_flows.sh and 160 kpps without the patch.
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds a new extra type to be able to diffirentiate
between RX responses on xen-netfront side with the adjusted offset
required for XDP processing.
The offset value from a guest is passed via xenstore.
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer says:
====================
V3: Reorder patches to cause less code churn.
The BPF selftest 'test_progs' contains many tests, that cover all the
different areas of the kernel where BPF is used. The CI system sees this
as one test, which is impractical for identifying what team/engineer is
responsible for debugging the problem.
This patchset add some options that makes it easier to create a shell
for-loop that invoke each (top-level) test avail in test_progs. Then each
test FAIL/PASS result can be presented the CI system to have a separate
bullet. (For Red Hat use-case in Beaker https://beaker-project.org/)
Created a public script[1] that uses these features in an advanced way.
Demonstrating howto reduce the number of (top-level) tests by grouping tests
together via using the existing test pattern selection feature, and then
using the new --list feature combined with exclude (-b) to get a list of
remaining test names that was not part of the groups.
[1] https://github.com/netoptimizer/prototype-kernel/blob/master/scripts/bpf_selftests_grouping.sh
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The program test_progs have some very useful ability to specify a list of
test name substrings for selecting which tests to run.
This patch add the ability to list the selected test names without running
them. This is practical for seeing which tests gets selected with given
select arguments (which can also contain a exclude list via --name-blacklist).
This output can also be used by shell-scripts in a for-loop:
for N in $(./test_progs --list -t xdp); do \
./test_progs -t $N 2>&1 > result_test_${N}.log & \
done ; wait
This features can also be used for looking up a test number and returning
a testname. If the selection was empty then a shell EXIT_FAILURE is
returned. This is useful for scripting. e.g. like this:
n=1;
while [ $(./test_progs --list -n $n) ] ; do \
./test_progs -n $n ; n=$(( n+1 )); \
done
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/159363985751.930467.9610992940793316982.stgit@firesoul
Edward Cree