We need to return QLA_FUNCTION_TIMEOUT immediately otherwise we mess up the
mailbox command state machine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If there is an error creating multiple response queues then we need to revert
the request queue mapping back to request queue 0.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This function can wait for 5min under certain scenarios. One of them is when
the port is down from switch and bus reset is issued. The bus reset used to
wait for 5 minutes for the loop and upper layer callers used to hang and give
stack trace because of getting stuck for 120 sec. It is legacy code that was
used when the driver used to do queuing of the commands.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
_scsih_smart_predicted_fault is called in an interrupt and therefore
must allocate memory using GFP_ATOMIC.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Synaptics touchpads on several Dell laptops, particularly Vostro V13
systems, may not respond properly to PS/2 commands and queries immediately
after resuming from suspend to RAM. This leads to unresponsive touchpad
after suspend/resume cycle.
Adding a 1-second delay after resetting the device allows touchpad to
finish initializing (calibrating?) and start reacting properly.
Reported-by: Daniel Manrique <daniel.manrique@canonical.com>
Tested-by: Daniel Manrique <daniel.manrique@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The error check (intr_status < 0) didn't work because intr_status is
a u8. Change its type to signed int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
New product ID reported by Harvey Braun on linuxwacom mailing list
and also tested this patch with new hardware.
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
arm_dma_zone_size is used by arm_bootmem_free() which is called by
paging_init(). Thus it needs to be set before calling it.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When using only subdev user-space operations the camera
interface input was not configured properly. Fix this by
updating the corresponding data structure in set_fmt
operation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ati_remote driver currently uses 2-byte scancodes. However, one of
those bytes is actually a checksum and therefore shouldn't be considered
as part of the scancode.
Fix the driver to only use the actual data byte as a scancode and to
check the checksum itself. Update the bundled keymaps accordingly.
Since ati_remote was only migrated to the rc subsystem for 3.2, the
previous scancodes weren't emitted on any stable kernel.
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise compilation breaks with:
...
after apparently no longer included recursively from other header files.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
priv gets dereferenced in mt9t112_set_params() so we should return
before calling that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 64-bit platforms assigning a pointer to a 32-bit variable causes a
compiler warning and cannot actually work. Soc-camera currently doesn't
support any 64-bit systems, but such platforms can be added in the
and in any case compiler warnings should be avoided.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is against the mainline v3.1 release (c3b92c8) and
fixes a compile error when building for OMAP3+DSS+VOUT
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Gary Thomas <gary@mlbassoc.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The sound driver refuses to load as module, because of the missing
MODULE_LICENSE("GPL").
The file header indicates that the driver is indeed published under
the GPL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mmc_suspend_host() tries to claim host during suspend
and release it only when the bus suspend operation is
compeleted. If CONFIG_MMC_UNSAFE_RESUME is defined and
the host is flagged as removable, mmc_suspend_host()
tries to remove the card. In this process, the file system
sync can get blocked trying to acquire host which is already
claimed by mmc_suspend_host() causing deadlock.
Fix this deadlock by releasing host before ->remove() is called.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that the driver is using dev_pm_ops the suspend operations in the
platform_driver structure won't get called so don't need to be there,
and certainly shouldn't be the same function as dev_pm_ops since the
signatures are different.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not power down the card in .set_ios(), unless MMC_POWER_OFF is
requested. This fixes the SDHI functionality on ecovec.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Do not power down the card in .set_ios(), unless MMC_POWER_OFF is
requested. This fixes the MMCIF interface functionality on ecovec boards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix wrong bus_ops->sleep check. (This isn't expected to have real-world
consequences, because the mmc core always defines both 'awake' and
'sleep' ops.)
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The eMMC 4.5 devices respond to only RESET and AWAKE command in the
sleep state. Hence the mmc switch command to notify power off state
should be sent before the device enters sleep state.
This patch fixes the same.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch skips the setting of the power notify state variable
for non eMMC 4.5 devices. Also fixes the problem of omap_hsmmc
noisy/broken for suspend resume reported by Kevin Hilman.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.
This patch also enables this quirk for certain Micron cards known to
have this problem.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes: drivers/mmc/host/sdhci-cns3xxx.c:110: error: 'THIS_MODULE'
undeclared here (not in a function)
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
When we can't configure the dma channel we want to fall
back to PIO. We do this by setting host->do_dma to zero.
This does not work as do_dma is used to see whether dma
can be used for the current transfer. Instead, we have
to set host->dma to NULL.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Record the clock after the divider as that is what all SYSCLK users see.
Without this the other clock configuration in the device comes out at
half rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
efi_call_phys_prelog() sets up a 1:1 mapping of the physical address
range in swapper_pg_dir. Instead of replacing then restoring entries
in swapper_pg_dir we should be using initial_page_table which already
contains the 1:1 mapping.
It's safe to blindly switch back to swapper_pg_dir in the epilog
because the physical EFI routines are only called before
efi_enter_virtual_mode(), e.g. before any user processes have been
forked. Therefore, we don't need to track which pgd was in %cr3 when
we entered the prelog.
The previous code actually contained a bug because it assumed that the
kernel was loaded at a physical address within the first 8MB of ram,
usually at 0x100000. However, this isn't the case with a
CONFIG_RELOCATABLE=y kernel which could have been loaded anywhere in
the physical address space.
Also delete the ancient (and bogus) comments about the page table
being restored after the lock is released. There is no locking.
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Darrent Hart <dvhart@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1323346250.3894.74.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
...and report the servers that try to return a delegation when the client
is using the CLAIM_DELEG_CUR open mode. That behaviour is explicitly
forbidden in RFC3530.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.samba.org/sfrench/cifs-2.6:
cifs: check for NULL last_entry before calling cifs_save_resume_key
cifs: attempt to freeze while looping on a receive attempt
cifs: Fix sparse warning when calling cifs_strtoUCS
CIFS: Add descriptions to the brlock cache functions
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Calling __pa() with an ioremap()ed address is invalid
x86, hpet: Immediately disable HPET timer 1 if rtc irq is masked
x86/intel_mid: Kconfig select fix
x86/intel_mid: Fix the Kconfig for MID selection
* 'spi/for-3.2' of git://git.pengutronix.de/git/wsa/linux-2.6:
spi/gpio: fix section mismatch warning
spi/fsl-espi: disable CONFIG_SPI_FSL_ESPI=m build
spi/nuc900: Include linux/module.h
spi/ath79: fix compile error due to missing include
Likely misuse of & vs &&.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are currently 2 places in the state recovery code, where we do not
take sufficient precautions before accessing the state->lock_states. In
both cases, we should be holding the state->state_lock.
Reported-by: Pascal Bouchareine <pascal@gandi.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://neil.brown.name/md:
md: raid5 crash during degradation
md/raid5: never wait for bad-block acks on failed device.
md: ensure new badblocks are handled promptly.
md: bad blocks shouldn't cause a Blocked status on a Faulty device.
md: take a reference to mddev during sysfs access.
md: refine interpretation of "hold_active == UNTIL_IOCTL".
md/lock: ensure updates to page_attrs are properly locked.
Chad Dupuis