Actually we can use the "clk" in the struct sdhci_pltfm_host. Also
change the "external clock" to "core clock" and kill two redundant
private functions in this driver as suggested by Ray Jui.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Actually we can use the "clk" in the struct sdhci_pltfm_host.
With this change we can also kill the private function for get
max clock in this driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is only one "clk" member in this driver specific private struct.
Actually we can use the "clk" member in the struct sdhci_pltfm_host,
and then kill this struct completely.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function clk_disable_unprepare() already take care of either error
or null cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the original tuning code, delay value is set to SD Bus Clock Delay
Register (SD_CLK_DELAY_SETTING) as (val | (Val << 7) | (val << 16)),
which means CLK_DELAY_IN1, CLK_DELAY_IN2 and CLK_DELAY_OUT are the
same and with 128 steps. This is doubtful. In CSR design specification
documents CS-304575-DR-3H, this issue is clarified, the delay[13:0] in
SD_CLK_DELAY_SETTING is simplied to the concatenation of {CLK_DELAY_IN2,
CLK_DELAY_IN1}.
Besides, for CMD19 tuning, no need to set CLK_DELAY_OUT([22,16]
of SD_CLK_DELAY_SETTING).
Signed-off-by: weijun yang <york.yang@csr.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We really don't want to get a card detect interrupt during probe time
since it can confuse things. Let's disable the card detect interrupt
until we're in a really good place: the end of probe. Let's also
simply avoid enabling the card detect interrupt if it's not used.
It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt. That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host(). On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children. I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:
Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host
Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.
The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.
We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command. This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.
Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should give dw_mmc a good reset after we apply power. On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.
Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It appears that we can confuse things if we try to turn on the MMC
clock when the power is off. Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command can terminate a data transfer between a memory card and
mmc controller.
As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.
After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
which depends on MMC_CAP_RUNTIME_RESUME capability.
On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.
And the total tuning time will be more than 400ms.
So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f4833
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
This change addresses following problem:
[ 2.560726] ------------[ cut here ]------------
[ 2.565341] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xec/0x118()
[ 2.574439] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 2.579821] Modules linked in:
[ 2.583038] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.18.0-next-20141216-00002-g4ff197fc1902-dirty #1318
[ 2.593796] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2.599892] [<c0014c44>] (unwind_backtrace) from [<c0011bbc>] (show_stack+0x10/0x14)
[ 2.607612] [<c0011bbc>] (show_stack) from [<c04953b8>] (dump_stack+0x70/0xbc)
[ 2.614822] [<c04953b8>] (dump_stack) from [<c0023444>] (warn_slowpath_common+0x74/0xb0)
[ 2.622885] [<c0023444>] (warn_slowpath_common) from [<c0023514>] (warn_slowpath_fmt+0x30/0x40)
[ 2.631569] [<c0023514>] (warn_slowpath_fmt) from [<c0063644>] (lockdep_trace_alloc+0xec/0x118)
[ 2.640246] [<c0063644>] (lockdep_trace_alloc) from [<c00df52c>] (__kmalloc+0x3c/0x1cc)
[ 2.648240] [<c00df52c>] (__kmalloc) from [<c0394970>] (clk_fetch_parent_index+0xb8/0xd4)
[ 2.656390] [<c0394970>] (clk_fetch_parent_index) from [<c0394a6c>] (clk_calc_new_rates+0xe0/0x1fc)
[ 2.665415] [<c0394a6c>] (clk_calc_new_rates) from [<c0394b40>] (clk_calc_new_rates+0x1b4/0x1fc)
[ 2.674181] [<c0394b40>] (clk_calc_new_rates) from [<c0395408>] (clk_set_rate+0x50/0xc8)
[ 2.682265] [<c0395408>] (clk_set_rate) from [<c0377708>] (sdhci_cmu_set_clock+0x68/0x16c)
[ 2.690503] [<c0377708>] (sdhci_cmu_set_clock) from [<c03735cc>] (sdhci_do_set_ios+0xf0/0x64c)
[ 2.699095] [<c03735cc>] (sdhci_do_set_ios) from [<c0373b48>] (sdhci_set_ios+0x20/0x2c)
[ 2.707080] [<c0373b48>] (sdhci_set_ios) from [<c035ddf0>] (mmc_power_up+0x118/0x1fc)
[ 2.714889] [<c035ddf0>] (mmc_power_up) from [<c035ecd0>] (mmc_start_host+0x44/0x6c)
[ 2.722615] [<c035ecd0>] (mmc_start_host) from [<c035fd60>] (mmc_add_host+0x58/0x7c)
[ 2.730341] [<c035fd60>] (mmc_add_host) from [<c037454c>] (sdhci_add_host+0x968/0xd94)
[ 2.738240] [<c037454c>] (sdhci_add_host) from [<c0377b60>] (sdhci_s3c_probe+0x354/0x52c)
[ 2.746406] [<c0377b60>] (sdhci_s3c_probe) from [<c0283b58>] (platform_drv_probe+0x48/0xa4)
[ 2.754733] [<c0283b58>] (platform_drv_probe) from [<c02824e8>] (driver_probe_device+0x13c/0x37c)
[ 2.763585] [<c02824e8>] (driver_probe_device) from [<c02827bc>] (__driver_attach+0x94/0x98)
[ 2.772003] [<c02827bc>] (__driver_attach) from [<c0280a60>] (bus_for_each_dev+0x54/0x88)
[ 2.780163] [<c0280a60>] (bus_for_each_dev) from [<c0281b48>] (bus_add_driver+0xe4/0x200)
[ 2.788322] [<c0281b48>] (bus_add_driver) from [<c0282dfc>] (driver_register+0x78/0xf4)
[ 2.796308] [<c0282dfc>] (driver_register) from [<c00089b0>] (do_one_initcall+0xac/0x1f0)
[ 2.804473] [<c00089b0>] (do_one_initcall) from [<c0673d94>] (kernel_init_freeable+0x10c/0x1d8)
[ 2.813153] [<c0673d94>] (kernel_init_freeable) from [<c0490058>] (kernel_init+0x28/0x108)
[ 2.821398] [<c0490058>] (kernel_init) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 2.828939] ---[ end trace 03cc00e539849d1f ]---
clk_set_rate() tries to take clk's prepare_lock mutex while being in atomic
context entered in sdhci_do_set_ios().
The solution is inspired by similar situation in sdhci_set_power() also called
from sdhci_do_set_ios():
spin_unlock_irq(&host->lock);
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
spin_lock_irq(&host->lock);
Note that since sdhci_s3c_set_clock() sets SDHCI_CLOCK_CARD_EN, proposed change
first resets this bit. It is reset anyway (by setting SDHCI_CLOCK_INT_EN bit
only) after call to clk_set_rate() in order to wait for the clock to stabilize
and is set again as soon as the clock becomes stable.
Signed-off-by: Paul Osmialowski <p.osmialowsk@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch provides a simple mmc-pwrseq-emmc driver, which controls
single gpio line. It perform standard eMMC hw reset procedure, as
descibed by Jedec 4.4 specification. This procedure is performed just
after MMC core enabled power to the given mmc host (to fix possible
issues if bootloader has left eMMC card in initialized or unknown
state), and before performing complete system reboot (also in case of
emergency reboot call). The latter is needed on boards, which doesn't
have hardware reset logic connected to emmc card and (limited or broken)
ROM bootloaders are unable to read second stage from the emmc card if
the card is left in unknown or already initialized state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jonas Jensen wanted to submit a patch for these, but apparently
forgot about it. I stumbled over this symptom first:
drivers/built-in.o: In function `moxart_probe':
:(.text+0x2af128): undefined reference to `of_dma_request_slave_channel'
This is because of_dma_request_slave_channel is an internal helper
and not exported to loadable module. I'm changing the driver to
use dma_request_slave_channel_reason() instead.
Further problems from inspection:
* The remove function must not call kfree on the host pointer,
because it is allocated together with the mmc_host.
* The clock is never released
* The dma_cap_mask_t is completely unused and can be removed
* deferred probing does not work if the dma driver is loaded
after the mmc driver.
This patch should fix all of the above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Host drivers have different ways to sends their "init stream" to the
card. Some need to do it as part of a request, some do it from the
->set_ios() callback in the MMC_POWER_ON state and some don't send an
"init stream" at all.
To be able to use the reset GPIOs from the simple MMC power sequence
provider, the card need to be powered and the "init stream" must not
have been sent.
To cope with these requirements, invoke mmc_pwrseq_post_power_on()
prior we change the state to MMC_POWER_ON in mmc_power_up().
Host drivers shall perform power up operations in the MMC_POWER_UP
state. Unfortunate three hosts (au1xmmc, cb710-mmc and toshsd) don't
conform to this expectation. Instead those ignore the MMC_POWER_UP
state and delays their power up operations to the MMC_POWER_ON state.
Those hosts needs to change their behavior to enable proper support for
the simple MMC power sequence provider.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Some WLAN chips attached to a SDIO interface, need a reference clock.
Since this is very common, extend the prseq_simple driver to support
an optional clock that is enabled prior the card power up procedure.
Note: the external clock is optional. Thus an error is not returned
if the clock is not found.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many WLAN attached to a SDIO/MMC interface, needs more than one pin for
their reset sequence. For example, is very common for chips to have two
pins: one for reset and one for power enable.
This patch adds support for more reset pins to the pwrseq_simple driver
and instead hardcoding a fixed number, it uses the of_gpio_named_count()
since the MMC power sequence is only built when CONFIG_OF is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I seem to understand that the sdhci-pxav3 and sdhci-pxav2 drivers are
only needed on the MMP architecture. So add a hardware dependency on
ARCH_MMP, so that other users don't get to build useless drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to erratum 'FE-2946959' both SDR50 and DDR50 modes require
specific clock adjustments in SDIO3 Configuration register.
This commit add the support of this register and for SDR50 or DDR50
mode use it as suggested by the erratum:
- Set the SDIO3 Clock Inv field in SDIO3 Configuration register to not
inverted.
- Set the Sample FeedBack Clock field to 0x1
[gregory.clement@free-electrons.com: port from 3.10]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to erratum 'ERR-7878951' Armada 38x SDHCI controller has
different capabilities than the ones shown in its registers:
- it doesn't support the voltage switching: it can work either with
3.3V or 1.8V supply
- it doesn't support the SDR104 mode
- SDR50 mode doesn't need tuning
The SDHCI_QUIRK_MISSING_CAPS quirk is used for updating the
capabilities accordingly.
[gregory.clement@free-electrons.com: port from 3.10]
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to erratum 'FE-2946959' both SDR50 and DDR50 modes require
specific clock adjustments in SDIO3 Configuration register. However,
this register was not part of the device tree binding. Even if the
binding can (and will) be extended we still need handling the case
where this register was not available. In this case we use the
SDHCI_QUIRK_MISSING_CAPS quirk remove them from the capabilities.
This commit is based on the work done by Marcin Wojtas<mw@semihalf.com>
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I observed the Host Control2 register isn't correctly restored
after runtime resuming on BG2Q. For example, the register reads
as 0x800c before runtime suspend, but it's set as 0x8004 after runtime
resuming. This could results in a non working host.
The reason is the Host Control2 is incorrectly reset when switching
voltage. We fix this by following the same sequence during initialization.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is a gap between xfer mode and command register writes,
tegra SDMMC controller can sometimes issue a spurious command before
the CMD register is written. To avoid this, these two registers need
to be written together in a single write operation.
This is implemented as an NVQUIRK as it applies to T114, T124 and
T132.
Signed-off-by: Pavan Kunapuli <pkunapuli@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is coming to fix compatibility issue of BKOPS_EN field of EXT_CSD.
In eMMC-5.1, BKOPS_EN was changed, and now it has two operational bits:
Bit 0 - MANUAL_EN
Bit 1 - AUTO_EN
In previous eMMC revisions, only Bit 0 was supported.
Signed-off-by: Alexey Skidanov <alexey.skidanov@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code checks "clk_delay_cycles > 0" to know whether the optional
"mrvl,clk_delay_cycles" is set or not. But of_property_read_u32() doesn't
touch clk_delay_cycles if the property is not set. And type of
clk_delay_cycles is u32, so we may always set pdata->clk_delay_cycles as a
random value.
This patch fix this problem by check the return value of of_property_read_u32()
to know whether the optional clk-delay-cycles is set or not.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: <stable@vger.kernel.org> # v3.6+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() is not (nor should it be) marked as __exit,
so we should not be using __exit_p() wrapper with it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() is not (nor should it be) marked as __exit,
so we should not be using __exit_p() wrapper with it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let MMC_SDHCI_BIG_ENDIAN_32BIT_BYTE_SWAPPER depend on MMC_SDHCI. Not
only this is more correct, but this also avoids breaking the alignment
of all other MMC_SDHCI_* options in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Config option MMC_RICOH_MMC's help text reads:
If unsure, say Y.
However the option defaults to N. Set the default to Y to match the
recommendation in the help text.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Philipl Langdale <philipl@overt.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DMA configuration has been removed from function mmci_dma_setup but the
local mask variable was not removed. This remains unused hence remove
it from the function and operations on it
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix a race condition that may cause an unhandled irq,
which results in big sdhci interrupt numbers and endless "mmc1: got irq
while runtime suspended" msgs before v3.15.
Consider following scenario:
CPU0 CPU1
sdhci_pxav3_runtime_suspend()
spin_lock_irqsave(&host->lock, flags);
sdhci_irq()
spining on the &host->lock
host->runtime_suspended = true;
spin_unlock_irqrestore(&host->lock, flags);
get the &host->lock
runtime_suspended is true now
return IRQ_NONE;
Fix this race by using the core sdhci.c supplied sdhci_runtime_suspend_host()
in runtime suspend hook which will disable card interrupts. We also use the
sdhci_runtime_resume_host() in the runtime resume hook accordingly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Directly return the result of mmc_blk_alloc_req() instead of assigning
and returning the variable md.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The need for reset GPIOs has several times been pointed out from
erlier posted patchsets. Especially some WLAN chips which are
attached to an SDIO interface may use a GPIO reset.
The reset GPIO is asserted at initialization and prior we start the
power up procedure. The GPIO will be de-asserted right after the power
has been provided to the card, from the ->post_power_on() callback.
Note, the reset GPIO is optional. Thus we don't return an error even if
we can't find a GPIO for the consumer.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
To add the core part for the MMC power sequence, let's start by adding
initial support for the simple MMC power sequence provider.
In this initial step, the MMC power sequence node are fetched and the
compatible string for the simple MMC power sequence provider are
verified.
At this point we don't parse the node for any properties, but instead
that will be handled from following patches. Since there are no
properties supported yet, let's just implement the ->alloc() and the
->free() callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
System on chip designs may specify a specific MMC power sequence. To
successfully detect an (e)MMC/SD/SDIO card, that power sequence must
be followed while initializing the card.
To be able to handle these SOC specific power sequences, let's add a
MMC power sequence interface. It provides the following functions to
help the mmc core to deal with these power sequences.
mmc_pwrseq_alloc() - Invoked from mmc_of_parse(), to initialize data.
mmc_pwrseq_pre_power_on()- Invoked in the beginning of mmc_power_up().
mmc_pwrseq_post_power_on()- Invoked at the end in mmc_power_up().
mmc_pwrseq_power_off()- Invoked from mmc_power_off().
mmc_pwrseq_free() - Invoked from mmc_free_host(), to free data.
Each MMC power sequence provider will be responsible to implement a set
of callbacks. These callbacks mirrors the functions above.
This patch adds the skeleton, following patches will extend the core of
the MMC power sequence and add support for a specific simple MMC power
sequence.
Do note, since the mmc_pwrseq_alloc() is invoked from mmc_of_parse(),
host drivers needs to make use of this API to enable the support for
MMC power sequences. Moreover the MMC power sequence support depends on
CONFIG_OF.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Commit 63589e92c2 ("clk: Ignore error and NULL pointers passed to
clk_{unprepare, disable}()") allows NULL or error pointer to be passed
unconditionally.
This patch is to simplify probe error and remove code paths.
However, we reserve the core clock checks in runtime suspend/resume code
because we want a little smaller latency.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Check sg_count before sending long data xfer.
Because dma_map_sg() return int, and sg_count may be negative,
so using int instead of unsigned.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error-code directly if no card exist, this can
make card remove faster.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci_f_sdh30.c:143:5-11: inconsistent IS_ERR and PTR_ERR, PTR_ERR on line 144
PTR_ERR should access the value just tested by IS_ERR
Semantic patch information:
There can be false positives in the patch case, where it is the call
IS_ERR that is wrong.
Generated by: scripts/coccinelle/tests/odd_ptr_err.cocci
CC: Vincent Yang <vincent.yang.fujitsu@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixed the following warning (reported by cppcheck):
[drivers/mmc/card/block.c:2149]: (warning) %d in format string (no. 1)
requires 'int' but the argument type is 'unsigned int'.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_host has .enable_dma callback now.
We don't need TMIO_MMC_HAVE_CTL_DMA_REG anymore.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, sh_mobile_sdhi can use 32bit DMA access in R-Cer Gen2.
Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Kevin Hao