This patch adds the regmap configuration tables and
core MFD handling for the CS47L24 and WM1831 codecs.
Note that compared to the other Arizona codecs, these devices
do not have an LDO1 or micsupp regulators, extcon driver, or
the DCVDD isolation control.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
For the WM5102 there is a dependency in the core code on wm5102_patch()
which only exists when CONFIG_MFD_WM5102 is defined. To avoid having
to sprinkle #ifdefs around the code it is given an alternative empty
stub version when CONFIG_MFD_WM5102 is deselected
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Allow the chip to completely power off if we enter runtime suspend and
there is no jack detection active. This is helpful for systems where
system suspend might remove the supplies to the CODEC, without informing
us. Note the powering off is done in runtime suspend rather than system
suspend, because we need to hold reset until the first time DCVDD is
powered anyway (which would be in runtime resume), and we might as well
save the extra power.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
arizona_extcon_do_magic does not lend a lot of clarity to the purpose
of the function, and as all the registers used are described in the
datasheet there is no need to obfuscate the code. This patch renames the
function to arizona_extcon_hp_clamp, as it controls clamping on the
headphone output.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This adds support for the Wolfson Microelectronics WM8280 and WM8281
codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
[Lee: Minor fixup to remove potentially uninitialised variable. ]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The wm5102 driver currently uses the snd_soc_codec mutex to protect its
ultrasonic response settings from concurrent access. This patch moves this
lock to the driver level. This will allow us to eventually remove the
snd_soc_codec mutex.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
We only request the control interface error IRQ if we set ctrlif_error,
as such we should only free it in that situation. Otherwise we will
attempt to free an IRQ we never requested and get a warning from the IRQ
core.
This patch moves the ctrlif_error variable into the arizona structure
and checks it in all cases we free the control interface error IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer versions of the IP have a lot of new interrupts and move several
existing interrupts. This patch adds the register definitions and regmap
hookup for these interrupts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer versions of the IP introduce short circuit protection which will
also shutdown the speaker. Rename the interrupt and associated register
bits associated with thermal events to better fit the function and avoid
conflict with future interrupt additions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
wm5110 has interrupts to signal that an output has fully enabled. This
patch adds in these interrupts although use is not made of them yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are no Arizona devices with 3 core supplies but we define a fix
array with space for 3 core supplies. Lower the ARIZONA_MAX_CORE_SUPPLIES
define to 2, to save a few bytes.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add controls to allow custom shaping of the ultrasonic response. This
custom shaping can be turned on/off at runtime, although, it should be
noted that settings will not affect a currently open audio stream,
they will be applied when the next audio stream is started.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch factors out the reading of GPIOs for the Arizona devices
into a helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch integrates the wm8997 into the Arizona mfd.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the device is used with an external DCVDD supply instead of the
internal LDO1 then an extra step is required when suspending and resuming
the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.
Do the ASoC side of this by storing the enable state in the core driver
structure and only writing to the device if a flag indicating that the
accessory detection side is in a state where it can have the headphone
output stage enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Some other device functions need to integrate with signal sources in the
audio portion (primarily for haptics) so allow CODEC to export the DAPM
context by pointing to it from the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM5110 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices. It combines an advanced DSP
feature set with a flexible, high-performance audio hub CODEC.
The support is based on the Arizona core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than open coding the enable GPIO control in the MFD core use the
API to push the management on to the regulator driver. The immediate
advantage is slight for most systems but this will in future allow device
configurations where an external regulator is used for DCVDD.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds core support for these devices.
In order to handle systems which do not use the generic clock API a
simple wrapper for the 32kHz clock domain in the devices is provided.
Once the generic clock API is widely available this code will be moved
over to use that.
For simplicity some WM5102 specific code is included in the core driver,
the effort involved in splitting the device out isn't worth it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Richard Fitzgerald