Give the stubs a VMA. This allows the removal of a truly nasty kludge to make
sure that mm->nr_ptes was correct in exit_mmap. The underlying problem was
always that the stubs, which have ptes, and thus allocated a page table,
weren't covered by a VMA.
This patch fixes that by using install_special_mapping in arch_dup_mmap and
activate_context to create the VMA. The stubs have to be moved, since
shift_arg_pages seems to assume that the stack is the only VMA present at that
point during exec, and uses vma_adjust to fiddle its VMA. However, that
extends the stub VMA by the amount removed from the stack VMA.
To avoid this problem, the stubs were moved to a different fixed location at
the start of the address space.
The init_stub_pte calls were moved from init_new_context to arch_dup_mmap
because I was occasionally seeing arch_dup_mmap not being called, causing
exit_mmap to die. Rather than figure out what was really happening, I decided
it was cleaner to just move the calls so that there's no doubt that both the
pte and VMA creation happen, no matter what. arch_exit_mmap is used to clear
the stub ptes at exit time.
The STUB_* constants in as-layout.h no longer depend on UM_TASK_SIZE, that
that definition is removed, along with the comments complaining about gcc.
Because the stubs are no longer at the top of the address space, some care is
needed while flushing TLBs. update_pte_range checks for addresses in the stub
range and skips them. flush_thread now issues two unmaps, one for the range
before STUB_START and one for the range after STUB_END.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the calculation and use of the usable address space size on the host.
task_size is gone, replaced with TASK_SIZE, which is calculated from
CONFIG_TOP_ADDR. get_kmem_end and set_task_sizes_skas are also gone.
host_task_size, which refers to the entire address space usable by the UML
kernel and which may be larger than the address space usable by a UML process,
since that has to end on a pgdir boundary, is replaced by CONFIG_TOP_ADDR.
STACK_TOP is now TASK_SIZE minus the two stub pages.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UML was panicing in the case of failures of libc calls which shouldn't happen.
This is an overreaction since a failure from libc doesn't normally mean that
kernel data structures are in an unknown state. Instead, the current process
should just be killed if there is no way to recover.
The case that prompted this was a failure of PTRACE_SETREGS restoring the same
state that was read by PTRACE_GETREGS. It appears that when a process tries
to load a bogus value into a segment register, it segfaults (as expected) and
the value is actually loaded and is seen by PTRACE_GETREGS (not expected).
This case is fixed by forcing a fatal SIGSEGV on the process so that it
immediately dies. fatal_sigsegv was added for this purpose. It was declared
as noreturn, so in order to pursuade gcc that it actually does not return, I
added a call to os_dump_core (and declared it noreturn) so that I get a core
file if somehow the process survives.
All other calls in arch/um/os-Linux/skas/process.c got the same treatment,
with failures causing the process to die instead of a kernel panic, with some
exceptions.
userspace_tramp exits with status 1 if anything goes wrong there. That will
cause start_userspace to return an error. copy_context_skas0 and
map_stub_pages also now return errors instead of panicing. Callers of thes
functions were changed to check for errors and do something appropriate.
Usually that's to return an error to their callers.
check_skas3_ptrace_faultinfo just exits since that's too early to do anything
else.
save_registers, restore_registers, and init_registers now return status
instead of panicing on failure, with their callers doing something
appropriate.
There were also duplicate declarations of save_registers and restore_registers
in os.h - these are gone.
I noticed and fixed up some whitespace damage.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some register accessor cleanups -
userspace() was calling restore_registers and save_registers for no
reason, since userspace() is on the libc side of the house, and these
add no value over calling ptrace directly
init_thread_registers and get_safe_registers were the same thing,
so init_thread_registers is gone
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Untangle UML headers somewhat and add some includes where they were
needed explicitly, but gotten accidentally via some other header.
arch/um/include/um_uaccess.h loses asm/fixmap.h because it uses no
fixmap stuff and gains elf.h, because it needs FIXADDR_USER_*, and
archsetjmp.h, because it needs jmp_buf.
pmd_alloc_one is uninlined because it needs mm_struct, and that's
inconvenient to provide in asm-um/pgtable-3level.h.
elf_core_copy_fpregs is also uninlined from elf-i386.h and
elf-x86_64.h, which duplicated the code anyway, to
arch/um/kernel/process.c, so that the reference to current_thread
doesn't pull sched.h or anything related into asm/elf.h.
arch/um/sys-i386/ldt.c, arch/um/kernel/tlb.c and
arch/um/kernel/skas/uaccess.c got sched.h because they dereference
task_structs. Its includes of linux and asm headers got turned from
"" to <>.
arch/um/sys-i386/bug.c gets asm/errno.h because it needs errno
constants.
asm/elf-i386 gets asm/user.h because it needs user_regs_struct.
asm/fixmap.h gets page.h because it needs PAGE_SIZE and PAGE_MASK and
system.h for BUG_ON.
asm/pgtable doesn't need sched.h.
asm/processor-generic.h defined mm_segment_t, but didn't use it. So,
that definition is moved to uaccess.h, which defines a bunch of
mm_segment_t-related stuff. thread_info.h uses mm_segment_t, and
includes uaccess.h, which causes a recursion. So, the definition is
placed above the include of thread_info. in uaccess.h. thread_info.h
also gets page.h because it needs PAGE_SIZE.
ObCheckpatchViolationJustification - I'm not adding a typedef; I'm
moving mm_segment_t from one place to another.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes a few functions into returning void. The return values
were not used anyway, so I think it should not be a problem. Also removed a
little leftover bit from TT mode.
Signed-off-by: Karol Swietlicki <magotari@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tidy kern_util.h. It turns out that most of the function declarations
aren't used, so they can go away. os.h no longer includes
kern_util.h, so files which got it through os.h now need to include it
directly. A number of other files never needed it, so these includes
are deleted.
The structure which was used to pass signal handlers from the kernel
side to the userspace side is gone. Instead, the handlers are
declared here, and used directly from libc code. This allows
arch/um/os-Linux/trap.c to be deleted, with its remnants being moved
to arch/um/os-Linux/skas/trap.c.
arch/um/os-Linux/tty.c had its inclusions changed, and it needed some
style attention, so it got tidied.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robert Day noticed a few unused headers in UML, so this gets rid of them.
Cc: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested by Geert Uytterhoeven - use const.h to get constants that are usable
in both C and assembly. I can't include it directly since this code can't
include kernel headers. const.h is also for numeric constants that can be
typed by tacking a "UL" or similar on the end. The constants here have to be
typed by casting them.
So, the relevant parts of const.h are copied here and modified in order to
allow the constants to be uncasted in assembly and casted in C.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch also does some improvements for uml code. Improvements include
dropping unnecessary cast, killing some unnecessary code and still some
constifying for pointers etc..
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bugs.c, for both i386 and x86_64, can undergo further cleaning -
The i386 arch_check_bugs only does one thing, so we might as
well inline the cmov checking.
The i386 includes can be trimmed down a bit.
arch_init_thread wasn't used, so it is deleted.
The panics in arch_handle_signal are turned into printks
because the process is about to get segfaulted anyway, so something is
dying no matter what happens here. Also, the return value was always
the same, so it contained no information, so it can be void instead.
The name is changed to arch_examine_signal because it doesn't handle
anything.
The caller of arch_handle_signal, relay_signal, does things in
a different order. The kernel-mode signal check is now first, which
puts everything else together, making things a bit clearer conceptually.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces a new way of checking for the cmov instruction. I use
signal handling instead of reading /proc/cpuinfo.
[ jdike - Fiddled the asm to make it obvious that it didn't mess with
any in-use registers and made test_for_host_cmov void ]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Karol Swietlicki <magotari@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates links which broke during the transition to the new UML
website.
Signed-off-by: Karol Swietlicki <magotari@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains varied fixes and improvements for some files under
arch/um/os-Linux/, such as a typo fix in a perror message, a missing
argument fix for a printf, some constifying for pointers and so on.
[ jdike - made sigprocmask failure return -errno instead of -1 ]
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
init.h started breaking now for some reason. It turns out that there wasn't a
definition of __used. Fixed this by copying the relevant stuff from
compiler.h in the userspace case, and including compiler.h in the kernel case.
[xiyou.wangcong@gmail.com: added definition of __section]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sometimes when UML is debugged gdb miss breakpoints.
When process traced by gdb do fork, debugger remove breakpoints from
child address space. There is possibility to trace more than one fork,
but this not work with UML, I guess (only guess) there is a deadlock -
gdb waits for UML and UML waits for gdb.
When clone() is called with SIGCHLD and CLONE_VM flags, gdb see this
as PTRACE_EVENT_FORK not as PTRACE_EVENT_CLONE and remove breakpoints
from child and at the same time from traced process, because either
have the same address space.
Maybe it is possible to do fix in gdb, but I'm not sure if there is
easy way to find out if traced and child processes share memory. So I
do fix for UML, it simply do not call clone() with both SIGCHLD and
CLONE_VM flags together. Additionally __WALL flag is used for
waitpid() to assure not miss clone and normal process events.
[ jdike - checkpatch fixes ]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the case of CONFIG_PRINTK being disabled. This requires a do-nothing
stub to be present in arch/um/include/user.h so that we don't get references
to printk from libc code.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The calculation of CONFIG_STUB_CODE and CONFIG_STUB_DATA didn't take into
account anything but 3G/1G and 2G/2G, leaving the other vmsplits out in the
cold.
I'd rather not duplicate the four known host vmsplit cases for each of these
symbols. I'd also like to calculate them based on the highest userspace
address.
The Kconfig language seems not to allow calculation of hex constants, so I
moved this to as-layout.h. CONFIG_STUB_CODE, CONFIG_STUB_DATA, and
CONFIG_STUB_START are now gone. In their place are STUB_CODE, STUB_DATA, and
STUB_START in as-layout.h.
i386 and x86_64 seem to differ as to whether an unadorned constant is an int
or a long, so I cast them to unsigned long so they can be printed
consistently. However, they are also used in stub.S, where C types don't work
so well. So, there are ASM_ versions of these constants for use in stub.S. I
also ifdef-ed the non-asm-friendly portion of as-layout.h.
With this in place, most of the rest of this patch is changing CONFIG_STUB_*
to STUB_*, except in stub.S, where they are changed to ASM_STUB_*.
defconfig has the old symbols deleted.
I also print these addresses out in case there is any problem mapping them on
the host.
The two stub.S files had some trailing whitespace, so that is cleaned up here.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A bunch of MTU-related cleanups in the network code.
First, there is the addition of the notion of a maximally-sized packet, which
is the MTU plus headers. This is used to size the skb that will receive a
packet. This allows ether_adjust_skb to go away, as it was used to resize the
skb after it was allocated.
Since the skb passed into the low-level read routine is no longer resized, and
possibly reallocated, there, they (and the write routines) don't need to get
an sk_buff **. They just need the sk_buff * now. The callers of
ether_adjust_skb still need to do the skb_put, so that's now inlined.
The MAX_PACKET definitions in most of the drivers are gone.
The set_mtu methods were all the same and did nothing, so they can be
removed.
The ethertap driver had a typo which doubled the size of the packet rather
than adding two bytes to it. It also wasn't defining its setup_size, causing
a zero-byte kmalloc and crash when the invalid pointer returned from kmalloc
was dereferenced.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are various uses of powers of 1000, plus the odd BILLION constant in the
time code. However, there are perfectly good definitions of *SEC_PER_*SEC in
linux/time.h which can be used instaed.
These are replaced directly in kernel code. Userspace code imports those
constants as UM_*SEC_PER_*SEC and uses these.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Put back an implementation of timeval_to_ns in arch/um/os-Linux/time.c.
tglx pointed out in his review of tickless support that there was a
perfectly good implementation of it in linux/time.h. The problem is that
this is userspace code which can't pull in kernel headers and there doesn't
seem to be a libc version.
So, I'm copying the version from linux/time.h rather than resurrecting my
version. This causes some declaration changes as it now returns a signed
value rather than an unsigned value.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, the idle loop now longer needs SIGALRM firing - it can just sleep for the
requisite amount of time and fake a timer interrupt when it finishes.
Any use of ITIMER_REAL now goes away. disable_timer only turns off
ITIMER_VIRTUAL. switch_timers is no longer needed, so it, and all calls, goes
away.
disable_timer now returns the amount of time remaining on the timer.
default_idle uses this to tell idle_sleep how long to sleep. idle_sleep will
call alarm_handler if nanosleep returns 0, which is the case if it didn't
return early due to an interrupt. Otherwise, it just returns.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable tickless support.
CONFIG_TICK_ONESHOT and CONFIG_NO_HZ are enabled.
itimer_clockevent gets CLOCK_EVT_FEAT_ONESHOT and an implementation of
.set_next_event.
CONFIG_UML_REAL_TIME_CLOCK goes away because it only makes sense when there is
a clock ticking away all the time. timer_handler now just calls do_IRQ once
without trying to figure out how many ticks to emulate.
The idle loop now needs to turn ticking on and off.
Userspace ticks keep happening as usual. However, the userspace loop keep
track of when the next wakeup should happen and suppresses process ticks until
that happens.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move timer signal initialization from init_irq_signals to a new function,
timer_init.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_interval took a timer type as an argument, but it always specified a
virtual timer. So, it is not needed, and it is gone, and set_interval is
simplified appropriately.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up the switching between virtual and real timers. The idle loop sleeps,
so the timer at that point must be real time. At all other times, the timer
must be virtual. Even when userspace is running, and the kernel is asleep,
the virtual timer is correct because the process timer will be running and the
process timer will be firing.
The timer switch used to be in the context switch and timer handler code.
This is moved to the idle loop and the signal handler, making it much more
clear why it is happening.
switch_timers now returns the old timer type so that it may be restored. The
signal handler uses this in order to restore the previous timer type when it
returns.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate hz() since its only purpose was to provide a kernel-space constant
to userspace code. This can be done instead by providing the constant
directly through kernel_constants.h.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The floating point fields in the pt_regs register file aren't used, so they
are deleted.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tidy the code affected by the floating point fixes.
A bunch of unused stuff is gone, including two sigcontext.c files,
which turned out to be entirely unneeded.
There are the usual fixes -
whitespace and style cleanups
copyright updates
emacs formatting comments gone
include cleanups
adding severities to printks
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle floating point state in across signals correctly. UML/i386 needs to
know whether the host does PTRACE_[GS]ETFPXREGS, so an arch_init_registers
hook is added, which on x86_64 does nothing.
UML doesn't save and restore floating point registers on kernel entry and
exit, so they need to be copied between the host process and the sigcontext.
save_fpx_registers and restore_fpx_registers are added for this purpose.
save_fp_registers and restore_fp_registers already exist.
There was a bunch of floating point state conversion code in
arch/um/sys-i386/ptrace.c which isn't needed there, but is needed in signal.c,
so it is moved over.
The i386 code now distinguishes between fp and fpx state and handles them
correctly. The x86_64 code just needs to copy state as-is between the host
process and the stack. There are also some fixes there to pass the correct
address of the floating point state around.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tidy the tlb flushing code.
With tt mode gone, there is no reason to have the capability to have
called directly from do_mmap, do_mprotect, and do_munmap, rather than
calling a function pointer that it is given.
There was a large amount of data that was passed from function to
function, being used at the lowest level, without being changed. This
stuff is now encapsulated in a structure which is initialized at the
top layer and passed down. This simplifies the code, reduces the
amount of code needed to pass the parameters around, and saves on
stack space.
A somewhat more subtle change is the meaning of the current operation
index. It used to start at -1, being pre-incremented when adding an
operation. It now starts at 0, being post-incremented, with
associated adjustments of +/- 1 on comparisons.
In addition, tlb.h contained a couple of declarations which had no
users outside of tlb.c, so they could be moved or deleted.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A number of files that were changed in the recent removal of tt mode
are userspace files which call the os_* wrappers instead of calling
libc directly. A few other files were affected by this, through
This patch makes these call glibc directly.
There are also style fixes in the affected areas.
os_print_error has no remaining callers, so it is deleted.
There is a interface change to os_set_exec_close, eliminating a
parameter which was always the same. The callers are fixed as well.
os_process_pc got its error path cleaned up.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes some userspace files which were calling libc through the os_*
wrappers.
It turns out that there was only one user of os_new_tty_pgrp, so it can be
deleted.
There are also some style and whitespace fixes in here.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before the removal of tt mode, access to a register on the skas-mode side of a
pt_regs struct looked like pt_regs.regs.skas.regs.regs[FOO]. This was bad
enough, but it became pt_regs.regs.regs.regs[FOO] with the removal of the
union from the middle. To get rid of the run of three "regs", the last field
is renamed to "gp".
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch folds mmu_context_skas into struct mm_context, changing all users
of these structures as needed.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_longjmp used to be needed when UML didn't have its own implementation of
setjmp and longjmp. They came from libc, and couldn't be called directly from
kernel code, as the libc jmp_buf couldn't be imported there. do_longjmp was a
userspace function which served to provide longjmp access to kernel code.
This is gone, and a number of void * pointers can now be jmp_buf *.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate some uses of __u64 in the physical memory support. It's hard to get
a definition of __u64 in both kernel and userspace code on x86_64, so this
changes them to unsigned long long.
There are also a copyright update and formatting comment removal from the
affected header.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Formatting changes in the files which have been changed in the course
of folding foo_skas functions into their callers. These include:
copyright updates
header file trimming
style fixes
adding severity to printks
These changes should be entirely non-functional.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes a number of simplifications enabled by the removal of
CHOOSE_MODE. There were lots of functions that looked like
int foo(args){
foo_skas(args);
}
The bodies of foo_skas are now folded into foo, and their declarations (and
sometimes entire header files) are deleted.
In addition, the union uml_pt_regs, which was a union between the tt and skas
register formats, is now a struct, with the tt-mode arm of the union being
removed.
It turns out that usr2_handler was unused, so it is gone.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Formatting changes in the files which have been changed in the course
of removing CHOOSE_MODE. These include:
copyright updates
header file trimming
style fixes
adding severity to printks
These changes should be entirely non-functional.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The next stage after removing code which depends on CONFIG_MODE_TT is removing
the CHOOSE_MODE abstraction, which provided both compile-time and run-time
branching to either tt-mode or skas-mode code.
This patch removes choose-mode.h and all inclusions of it, and replaces all
CHOOSE_MODE invocations with the skas branch. This leaves a number of trivial
functions which will be dealt with in a later patch.
There are some changes in the uaccess and tls support which go somewhat beyond
this and eliminate some of the now-redundant functions.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Formatting changes in the files which have been changed in the
tt-removal patchset so far. These include:
copyright updates
header file trimming
style fixes
adding severity to printks
indenting Kconfig help according to the predominant kernel style
These changes should be entirely non-functional.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes thread.h, which turns out not to be needed any more.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset throws out tt mode, which has been non-functional for a while.
This is done in phases, interspersed with code cleanups on the affected files.
The removal is done as follows:
remove all code, config options, and files which depend on
CONFIG_MODE_TT
get rid of the CHOOSE_MODE macro, which decided whether to
call tt-mode or skas-mode code, and replace invocations with their
skas portions
replace all now-trivial procedures with their skas equivalents
There are now a bunch of now-redundant pieces of data structures, including
mode-specific pieces of the thread structure, pt_regs, and mm_context. These
are all replaced with their skas-specific contents.
As part of the ongoing style compliance project, I made a style pass over all
files that were changed. There are three such patches, one for each phase,
covering the files affected by that phase but no later ones.
I noticed that we weren't freeing the LDT state associated with a process when
it exited, so that's fixed in one of the later patches.
The last patch is a tidying patch which I've had for a while, but which caused
inexplicable crashes under tt mode. Since that is no longer a problem, this
can now go in.
This patch:
Start getting rid of tt mode support.
This patch throws out CONFIG_MODE_TT and all config options, code, and files
which depend on it.
CONFIG_MODE_SKAS is gone and everything that depends on it is included
unconditionally.
The few changed lines are in re-written Kconfig help, lines which needed
something skas-related removed from them, and a few more which weren't
strictly deletions.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tidying of the UML physical memory system. These are mostly style fixes,
however the includes were cleaned as well. This uncovered a need for
mem_user.h to be included in mode_kern_skas.h.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Throw out a lot of code dealing with saving and restoring floating-point
state. In skas mode, where processes run in a restoring floating-point state
on kernel entry and exit is pointless.
This eliminates most of arch/um/os-Linux/sys-{i386,x86_64}/registers.c. Most
of what remained is now arch-indpendent, and can be moved up to
arch/um/os-Linux/registers.c. Both arches need the jmp_buf accessor
get_thread_reg, and i386 needs {save,restore}_fp_regs because it cheats during
sigreturn by getting the fp state using ptrace rather than copying it out of
the process sigcontext.
After this, it turns out that arch/um/include/skas/mode-skas.h is almost
completely unneeded. The declarations in it are variables which either don't
exist or which don't have global scope. The one exception is
kill_off_processes_skas. If that's removed, this header can be deleted.
This uncovered a bug in user.h, which wasn't correctly making sure that a
size_t definition was available to both userspace and kernelspace files.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Map all of physical memory as executable to avoid having to change stack
protections during fork and exit.
unprotect_stack is now called only from MODE_TT code, so it is marked as such.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of asm/page.h from libc code. This header seems to be
disappearing, and UML doesn't make much use of it anyway.
The one use, PAGE_SHIFT in stub.h, is handled by copying the constant from the
kernel side of the house in common_offsets.h.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the generic console operations are in a userspace file, we
can do the following:
directly call into libc instead of through the os_* wrappers
eliminate os_window_size since it has only one user
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a crash caused by an interrupt coming in when an IRQ stack
is being torn down. When this happens, handle_signal will loop, setting up
the IRQ stack again because the tearing down had finished, and handling
whatever signals had come in.
However, to_irq_stack returns a mask of pending signals to be handled, plus
bit zero is set if the IRQ stack was already active, and thus shouldn't be
torn down. This causes a problem because when handle_signal goes around
the loop, sig will be zero, and to_irq_stack will duly set bit zero in the
returned mask, faking handle_signal into believing that it shouldn't tear
down the IRQ stack and return thread_info pointers back to their original
values.
This will eventually cause a crash, as the IRQ stack thread_info will
continue pointing to the original task_struct and an interrupt will look
into it after it has been freed.
The fix is to stop passing a signal number into to_irq_stack. Rather, the
pending signals mask is initialized beforehand with the bit for sig already
set. References to sig in to_irq_stack can be replaced with references to
the mask.
[akpm@linux-foundation.org: use UL]
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
UML had two wrapper procedures for kmalloc, um_kmalloc and um_kmalloc_atomic
because the flag constants weren't available in userspace code.
kern_constants.h had made kernel constants available for a long time, so there
is no need for these wrappers any more. Rather, userspace code calls kmalloc
directly with the userspace versions of the gfp flags.
kmalloc isn't a real procedure, so I had to essentially copy the inline
wrapper around __kmalloc.
vmalloc also had its own wrapper for no good reason. This is now gone.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
run_helper and run_helper_thread had arguments which were the same in all
callers. run_helper's stack_out was always NULL and run_helper_thread's
stack_order was always 0. These are now gone, and the constants folded
into the code.
Also fixed leaks of the helper stack in the AIO and SIGIO code.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup of the SIGWINCH support.
Some code and comment reformatting.
The stack used for SIGWINCH threads was leaked. This is now fixed by storing
it with the pid and other information, and freeing it when the thread is
killed.
If something goes wrong with a WIGWINCH thread, and this is discovered in the
interrupt handler, the winch record would leak. It is now freed, except that
the IRQ isn't freed. This is hard to do from interrupt context. This has the
side-effect that the IRQ system maintains a reference to the freed structure,
but that shouldn't cause a problem since the descriptor is disabled.
register_winch_irq is now much better about cleaning up after an
initialization failure.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the host side of a console can't be opened, this will now produce visible
error messages.
enable_chan now returns a status and this is passed up to con_open and
ssl_open, which will complain if anything went wrong.
The default host device for the serial line driver is now a pts device rather
than a pty device since lots of hosts have LEGACY_PTYS disabled. This had
always been failing on such hosts, but silently.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Major tidying of the xterm console driver:
got rid of the tt-mode gdb support
tidied up the includes
fixed lots of style violations
replaced os_* calls with glibc calls in xterm.c
all printk calls now have a severity indicator
the error paths of xterm_open are closer to being right
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Distros seem to be removing PAGE_SIZE from asm/page.h. So, the libc side of
UML should stop using it.
I replace it with UM_KERN_PAGE_SIZE, which is defined to be the same as
PAGE_SIZE on the kernel side of the house. I could also use getpagesize(),
but it's more important that UML have the same value of PAGE_SIZE everywhere.
It's conceivable that it could be built with a larger PAGE_SIZE, and use of
getpagesize() would break that badly.
PAGE_MASK got the same treatment, as it is closely tied to PAGE_SIZE.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__NR_syscall_max is done in x86_64 asm-offsets; do an equivalent in
uml kern_constants.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a separate IRQ stack. This differs from i386 in having the entire
interrupt run on a separate stack rather than starting on the normal kernel
stack and switching over once some preparation has been done. The underlying
mechanism, is of course, sigaltstack.
Another difference is that interrupts that happen in userspace are handled on
the normal kernel stack. These cause a wait wakeup instead of a signal
delivery so there is no point in trying to switch stacks for these. There's
no other stuff on the stack, so there is no extra stack consumption.
This quirk makes it possible to have the entire interrupt run on a separate
stack - process preemption (and calls to schedule()) happens on a normal
kernel stack. If we enable CONFIG_PREEMPT, this will need to be rethought.
The IRQ stack for CPU 0 is declared in the same way as the initial kernel
stack. IRQ stacks for other CPUs will be allocated dynamically.
An extra field was added to the thread_info structure. When the active
thread_info is copied to the IRQ stack, the real_thread field points back to
the original stack. This makes it easy to tell where to copy the thread_info
struct back to when the interrupt is finished. It also serves as a marker of
a nested interrupt. It is NULL for the first interrupt on the stack, and
non-NULL for any nested interrupts.
Care is taken to behave correctly if a second interrupt comes in when the
thread_info structure is being set up or taken down. I could just disable
interrupts here, but I don't feel like giving up any of the performance gained
by not flipping signals on and off.
If an interrupt comes in during these critical periods, the handler can't run
because it has no idea what shape the stack is in. So, it sets a bit for its
signal in a global mask and returns. The outer handler will deal with this
signal itself.
Atomicity is had with xchg. A nested interrupt that needs to bail out will
xchg its signal mask into pending_mask and repeat in case yet another
interrupt hit at the same time, until the mask stabilizes.
The outermost interrupt will set up the thread_info and xchg a zero into
pending_mask when it is done. At this point, nested interrupts will look at
->real_thread and see that no setup needs to be done. They can just continue
normally.
Similar care needs to be taken when exiting the outer handler. If another
interrupt comes in while it is copying the thread_info, it will drop a bit
into pending_mask. The outer handler will check this and if it is non-zero,
will loop, set up the stack again, and handle the interrupt.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replaced task_protections with stack_protections since they do the same
thing, and task_protections was misnamed anyway.
This needs THREAD_SIZE, so that's imported via common-offsets.h
Also tidied up the code in the vicinity.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Declare strlcpy and strlcat more correctly.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More trimming of the page fault path.
Permissions are passed around in a single int rather than one bit per
int. The permission values are copied from libc so that they can be
passed to mmap and mprotect without any further conversion.
The register sets used by do_syscall_stub and copy_context_skas0 are
initialized once, at boot time, rather than once per call.
wait_stub_done checks whether it is getting the signals it expects by
comparing the wait status to a mask containing bits for the signals of
interest rather than comparing individually to the signal numbers. It
also has one check for a wait failure instead of two. The caller is
expected to do the initial continue of the stub. This gets rid of an
argument and some logic. The fname argument is gone, as that can be
had from a stack trace.
user_signal() is collapsed into userspace() as it is basically one or
two lines of code afterwards.
The physical memory remapping stuff is gone, as it is unused.
flush_tlb_page is inlined.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Give the page fault code a specialized path. There is only one page to look
at, so there's no point in going into the general page table walking code.
There's only going to be one host operation, so there are no opportunities for
merging. So, we go straight to the pte we want, figure out what needs doing,
and do it.
While I was in here, I fixed the wart where the address passed to unmap was a
void *, but an unsigned long to map and protect.
This gives me just under 10% on a kernel build.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename os_{read_write}_file_k back to os_{read_write}_file, delete
the originals and their bogus infrastructure, and fix all the callers.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dump core after a panic. This will provide better debugging information than
is currently available.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch starts the removal of a very old, very broken piece of code. This
stems from the problem of passing a userspace buffer into read() or write() on
the host. If that buffer had not yet been faulted in, read and write will
return -EFAULT.
To avoid this problem, the solution was to fault the buffer in before the
system call by touching the pages that hold the buffer by doing a copy-user of
a byte to each page. This is obviously bogus, but it does usually work, in tt
mode, since the kernel and process are in the same address space and userspace
addresses can be accessed directly in the kernel.
In skas mode, where the kernel and process are in separate address spaces, it
is completely bogus because the userspace address, which is invalid in the
kernel, is passed into the system call instead of the corresponding physical
address, which would be valid. Here, it appears that this code, on every host
read() or write(), tries to fault in a random process page. This doesn't seem
to cause any correctness problems, but there is a performance impact. This
patch, and the ones following, result in a 10-15% performance gain on a kernel
build.
This code can't be immediately tossed out because when it is, you can't log
in. Apparently, there is some code in the console driver which depends on
this somehow.
However, we can start removing it by switching the code which does I/O using
kernel addresses to using plain read() and write(). This patch introduces
os_read_file_k and os_write_file_k for use with kernel buffers and converts
all call locations which use obvious kernel buffers to use them. These
include I/O using buffers which are local variables which are on the stack or
kmalloc-ed. Later patches will handle the less obvious cases, followed by a
mass conversion back to the original interface.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there's a segfault inside the kernel, we want a dump of the registers at
the point of the segfault, not the registers at the point of calling panic or
the last userspace registers.
sig_handler_common_skas now uses a static register set in the case of a
SIGSEGV to avoid messing up the process registers if the segfault turns out to
be non-fatal.
The architecture sigcontext-to-pt_regs copying code was repurposed to copy
data out of the SEGV stack frame.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tidying in preparation for the segfault register dumping patch which follows.
void * pointers are changed to union uml_pt_regs *. This makes the types
match reality, except in arch_fixup, which is changed to operate on a union
uml_pt_regs. This fixes a bug in the call from segv_handler, which passes a
union uml_pt_regs, to segv, which expects to pass a struct sigcontext to
arch_fixup.
Whitespace and other style fixes.
There's also a errno printk fix.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
userspace code used to have to call the kernelspace function page_size() in
order to determine the value of the kernel's PAGE_SIZE. Since this is now
available directly from kern_constants.h as UM_KERN_PAGE_SIZE, page_size() can
be deleted and calls changed to use the constant.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up arch/um/kernel/process.c:
- lots of return(x); -> return x; conversions
- a number of the small functions are either unused, in which case they are
gone, along any declarations in a header, or could be made static.
- current_pid is ifdefed on CONFIG_MODE_TT and its declaration is ifdefed on
both CONFIG_MODE_TT and UML_CONFIG_MODE_TT because we don't know whether
it's being used in a userspace or kernel file.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To look at users I did:
$ find arch/um/ include/asm-um -name '*.[ch]'|xargs grep -r 'net_kern\.h'
+-l|xargs grep '\<user\>'
Most users just cast user to the appropriate pointer, the remaining ones are
fixed here. In net_kern.c, I'm almost sure that save trick is not needed
anymore, but I've not verified it.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
user_util.h isn't needed any more, so delete it and remove all includes of it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rescue the useful contents of the soon-to-be-gone user-util.h.
pty.c now gets ptsname from stdlib.h like it should have always done.
CATCH_EINTR is now in os.h, although perhaps all usage should be under
os-Linux at some point.
get_pty is also in os.h.
This patch restores the old definition of ARRAY_SIZE in user.h. This file is
included only in userspace files, so there will be no conflict with the
kernel's new ARRAY_SIZE. The copy of the kernel's ARRAY_SIZE and associated
infrastructure is now gone.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves all the the symbols defined in um_arch.c, which are mostly
boundaries between different parts of the UML kernel address space, to a new
header, as-layout.h. There are also a few things here which aren't really
related to address space layout, but which don't really have a better place to
go.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the declarations of the architecture hooks from user_util.h
to a new header, arch.c, and adds the necessary includes to files which need
those declarations.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch narrows the sigio interface. The boot-time SIGIO testing used to
be in start_up.c, which meant that pty_output_sigio and pty_close_sigio needed
to be global. By moving that code here, those can become static and the
declarations moved from user_util.h.
os_check_bugs is also here because it only does the SIGIO checking. If it
does more, it'll probably move back to start_up.c.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can use a gcc extension to ensure that ARRAY_SIZE() is handed an array,
not a pointer. This is especially important when code is changed from a
fixed array to a pointer. I assume the Intel compiler doesn't support
__builtin_types_compatible_p.
[jdike@addtoit.com: uml: update UML definition of ARRAY_SIZE]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a number of problems associated with network interface hotplug.
The userspace initialization function can fail in some cases, but the
failure was never passed back to eth_configure, which proceeded with the
configuration. This results in a zombie device that is present, but can't
work. This is fixed by allowing the initialization routines to return an
error, which is checked, and the configuration aborted on failure.
eth_configure failed to check for many failures. Even when it did check,
it didn't undo whatever initializations has already happened, so a present,
but partially initialized and non-working device could result. It now
checks everything that can fail, and bails out, undoing whatever had been
done.
The return value of eth_configure was always ignored, so it is now just
void.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the host_info string from util.c to um_arch.c, where it is
actually initialized and used. Also document its lack of locking.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of a bunch of unused stuff -
cpu_feature had no users
linux_prog is little-used, so its declaration is moved to the
user for easy deletion when the whole file goes away
a long-unused debugging aid in helper.c is gone
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a few miscellaneous compilation problems -
an assignment with mismatched types in ldt.c
a missing include in mconsole.h which needs a definition of uml_pt_regs
I missed removing an include of user_util.h in hostfs
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses MAX_REG_NR consistently to refer to the register file size.
FRAME_SIZE isn't sufficient because on x86_64, it is smaller than the
ptrace register file size. MAX_REG_NR was introduced as a consistent way
to get the number of registers, but wasn't used everywhere it should be.
When this causes a problem, it makes PTRACE_SETREGS fail on x86_64 because
of a corrupted segment register value in the known-good register file. The
patch also adds a register dump at that point in case there are any future
problems here.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
os_usr1_signal() is totally unused, os_usr1_process() is used only by TT mode.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove in-source externs, linux/init.h is included in all cases.
This is a fixups for "Dynamic kernel command-line" patch.
It also includes some uml __init fixups so that we can __initdata also its
command_line.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Rename saved_command_line into boot_command_line.
2. Set command_line as __initdata.
Signed-off-by: Alon Bar-Lev <alon.barlev@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86_64 needs some TLS fixes. What was missing was remembering the child
thread id during clone and stuffing it into the child during each context
switch.
The %fs value is stored separately in the thread structure since the host
controls what effect it has on the actual register file. The host also needs
to store it in its own thread struct, so we need the value kept outside the
register file.
arch_prctl_skas was fixed to call PTRACE_ARCH_PRCTL appropriately. There is
some saving and restoring of registers in the ARCH_SET_* cases so that the
correct set of registers are changed on the host and restored to the process
when it runs again.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an error message when two umids are put on the command line.
umid.h is kind of pointless since it only declares one thing, and that
is already declared in os.h.
Commented the lack of locking of some data in os-Linux/umid.h.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix formatting in the sigio code.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We shouldn't be using the os wrappers from os code - we can use libc directly.
This patch replaces wrapper calls with libc calls.
It turns out that os_sigio_async had only one caller, which was in startup.c,
so that function is moved there and its name changed.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Locking comments and emacs comment removal in the low-level memory and
temp file code.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A bunch of the signal handlers can be made static.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
syscall_index and next_syscall_index turn out not to be used.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate the open_mutex after complaints from Blaisorblade. It turns out
that the tty count provides the information needed to tell whether we are the
first opener or last closer.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the last vestiges of devfs from console registration. Change the name
of the function, plus remove a couple of unused fields from the line_driver
structure.
struct lines is no longer needed, all traces of it are gone.
The only way that I can see to mark a structure as being almost-const is to
individually const the fields. This is the case for the line_driver
structure, which has only one modifiable field - a list_head in a
sub-structure.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Whitespace fixes and emacs comment removal.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The chan_opts structure is mostly const, and needs no locking. Comment the
lack of locking on the one field that can change.
Make all the other fields const. It turned out that console_open_chan didn't
use its chan_opts argument, so that is deleted from the function and its
callers.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some whitespace and coding style cleanups in the network driver code.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The registration of host network transports needed some locking. The
transport list itself is locked, but calls to the registration routines are
not. This is compensated for by checking that a transport structure is not
yet on any list.
I also took the opportunity to const all fields in the transport structure
except the list, which obviously can be modified.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some comment and whitespace cleanups in the console and mconsole code.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Dike