* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: at91_mci: fix hanging and rework to match flowcharts
mmc: at91_mci typo
sdhci: Fix "Unexpected interrupt" handling
mmc: fix silly copy-and-paste error
mmc: move layer init and workqueue to core file
mmc: refactor host class handling
mmc: refactor bus operations
sdhci: add ene controller id
mmc: bounce requests for simple hosts
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits)
bonding/bond_main.c: make 2 functions static
ps3: gigabit ethernet driver for PS3, take3
[netdrvr] Fix dependencies for ax88796 ne2k clone driver
eHEA: Capability flag for DLPAR support
Remove sk98lin ethernet driver.
sunhme.c:quattro_pci_find() must be __devinit
bonding / ipv6: no addrconf for slaves separately from master
atl1: remove write-only var in tx handler
macmace: use "unsigned long flags;"
Cleanup usbnet_probe() return value handling
netxen: deinline and sparse fix
eeprom_93cx6: shorten pulse timing to match spec (bis)
phylib: Add Marvell 88E1112 phy id
phylib: cleanup marvell.c a bit
AX88796 network driver
IOC3: Switch to pci refcounting safe APIs
e100: Fix Tyan motherboard e100 not receiving IPMI commands
QE Ethernet driver writes to wrong register to mask interrupts
rrunner.c:rr_init() must be __devinit
tokenring/3c359.c:xl_init() must be __devinit
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (32 commits)
[libata] sata_mv: print out additional chip info during probe
[libata] Use ATA_UDMAx standard masks when filling driver's udma_mask info
[libata] AHCI: Add support for Marvell AHCI-like chips (initially 6145)
[libata] Clean up driver udma_mask initializers
libata: Support chips with 64K PRD quirk
Add a PCI ID for santa rosa's PATA controller.
sata_sil24: sil24_interrupt() micro-optimisation
Add irq_flags to struct pata_platform_info
sata_promise: cleanups
[libata] pata_ixp4xx: kill unused var
ata_piix: fix pio/mwdma programming
[libata] ahci: minor internal cleanups
[ATA] Add named constant for ATAPI command DEVICE RESET
[libata] sata_sx4, sata_via: minor documentation updates
[libata] ahci: minor internal cleanups
[libata] ahci: Factor out SATA port init into a separate function
[libata] pata_sil680: minor cleanups from benh
[libata] sata_sx4: named constant cleanup
[libata] pata_ixp4xx: convert to new EH
[libata] pdc_adma: Reorder initializers with a couple structs
...
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] vmlogrdr function annotation.
[S390] s390: rename CPU_IDLE to S390_CPU_IDLE
[S390] cio: Remove prototype for non-existing function cmf_reset().
[S390] zcrypt: fix request timeout handling
[S390] system call optimization.
[S390] dasd: Avoid compile warnings on !CONFIG_DASD_PROFILE
[S390] Remove volatile from atomic_t
[S390] Program check in diag 210 under 31 bit
[S390] Bogomips calculation for 64 bit.
[S390] smp: Merge smp_count_cpus() and smp_get_save_areas().
[S390] zcore: Fix __user annotation.
[S390] fixed cdl-format detection.
[S390] sclp: Test facility list before executing a service call.
[S390] sclp: introduce some new interfaces.
[S390] Fixed comment typo.
[S390] vmcp cleanup
* 'splice-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block:
pipe: add documentation and comments
pipe: change the ->pin() operation to ->confirm()
Remove remnants of sendfile()
xip sendfile removal
splice: completely document external interface with kerneldoc
sendfile: remove bad_sendfile() from bad_file_ops
shmem: convert to using splice instead of sendfile()
relay: use splice_to_pipe() instead of open-coding the pipe loop
pipe: allow passing around of ops private pointer
splice: divorce the splice structure/function definitions from the pipe header
splice: relay support
sendfile: convert nfsd to splice_direct_to_actor()
sendfile: convert nfs to using splice_read()
loop: convert to using splice_direct_to_actor() instead of sendfile()
splice: add void cookie to the actor data
sendfile: kill generic_file_sendfile()
sendfile: remove .sendfile from filesystems that use generic_file_sendfile()
sys_sendfile: switch to using ->splice_read, if available
vmsplice: add vmsplice-to-user support
splice: abstract out actor data
* 'trivial-2.6.23' of git://git.kernel.dk/data/git/linux-2.6-block:
Documentation/block/barrier.txt is not in sync with the actual code: - blk_queue_ordered() no longer has a gfp_mask parameter - blk_queue_ordered_locked() no longer exists - sd_prepare_flush() looks slightly different
Use list_for_each_entry() instead of list_for_each() in the block device
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
block/Kconfig already has its own "menuconfig" so remove these
Use menuconfigs instead of menus, so the whole menu can be disabled at once
cfq-iosched: fix async queue behaviour
unexport bio_{,un}map_user
Remove legacy CDROM drivers
[PATCH] fix request->cmd == INT cases
cciss: add new controller support for P700m
[PATCH] Remove acsi.c
[BLOCK] drop unnecessary bvec rewinding from flush_dry_bio_endio
[PATCH] cdrom_sysctl_info fix
blk_hw_contig_segment(): bad segment size checks
[TRIVIAL PATCH] Kill blk_congestion_wait() stub for !CONFIG_BLOCK
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This is the third submission of the network driver for PS3.
The differences from the previous one are:
- renamed source file names so that their prefix can match
with the module name
- added cbe-oss-dev@ozlabs.org line for MAINTAINER file
- changed some in copyright comments
If there are no more comments, please apply for 2.6.23.
Thank you
--
Subject: PS3: Ethernet driver
From: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Add Gigabit Ethernet support for the PS3 game console. The module will
be called ps3_gelic.
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch introduces a capability flag that is used by the DLPAR userspace
tool to check which DLPAR features are supported by the eHEA driver.
Missing goto has been included.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing). This causes DAD and RS
packets to be sent from the slave. These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).
This patch alters the behavior so that addrconf will only run on
the master device itself. I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master. This is consistent with the IPv4 behavior for bonding.
This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.
The eql driver also uses the IFF_SLAVE flag. I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on an original idea by John W. Linville.
It is the missing part of 42d45ccd60636c28e35c2016f091783bc14ad99c
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM. So we must provide its ethernet address by another way.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the IOC3 driver to use ref counting pci interfaces so that we can
obsolete the (usually unsafe) pci_find_{slot/device} interfaces and avoid
future authors writing hotplug-unsafe device drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Build fixes:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 82550 & 51 parts have an extended configuration block that
includes a bit "GMRC", required to enable the expected TCO behavior,
in config byte offset 22d. The config block sent by the failing driver
does include the extension area, but this bit is not initialised,
and the downlaod only specifies 0x16 bytes to be sent to the NIC
(thaht's bytes 00..21d). By initializing the GMRC bit, and extending
the download size for D102+ MACs, the problem is resolved.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The QE Ethernet driver was writing to the wrong register to mask interrupts.
In ucc_geth_stop(), it was clearing UCCE instead of UCCM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We intend this patch to improve spidernet interrupt handling to be
more strict. We had following problem and this patch solves it.
-when CONFIG_DEBUG_SHIRQ=y, request_irq() calls handler().
-when spider_net_open() is called, it calls request_irq() which calls
spider_net_interrupt().
-if some specific interrupt bit is set at this timing, it calls
netif_rx_schedule() and spider_net_poll() is scheduled.
-spider_net_open() calls netif_poll_enable() which clears the bit
__LINK_STATE_RX_SCHED.
-when spider_net_poll() is called, it calls netif_rx_complete() which
causes BUG_ON() because __LINK_STATE_RX_SCHED is not set.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 3cSOHO100-TX needs a mdio_sync() before mdio_read() to read the MII
transceiver registers properly. Adding EXTRA_PREAMBLE to drv_flags of the
3cSOHO100-TX will force this.
This problem exists already for years (I checked back to 2.6.8).
Setting duplex for the 3cSOHO100-TX was more or less a random process.
Till 2.6.15 it was more likely that the diver ends up in half
duplex mode, after the code change in 2.6.16 it was more likely
to end up in full duplex mode. I wonder why nobody noticed this earier.
Hopefully addresses
Bug 7454 3c59x (3cSOHO100-TX Hurricane) slow network bug
http://bugzilla.kernel.org/show_bug.cgi?id=7454
and
Bug 3654 3cSOHO100-TX: No MII transceiver present
http://bugzilla.kernel.org/show_bug.cgi?id=3654
Cc: Jonas Sandberg <jonassa@gmail.com>
Cc: Jon Sanchez <bugs@niluje.net>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use roundup() macro to size receive buffer.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If packet larger than MTU is received, the driver uses hardware to
truncate the packet. Use the status registers to catch/drop them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sonic Zhang