The revision checking in l2c310_enable() was not correct; we were
masking the part number rather than the revision number. Fix this
to use the correct macro.
Fixes: 4374d64933 ("ARM: l2c: add automatic enable of early BRESP")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit ca8f0b0a54 ("ARM: ensure C page table setup code follows
assembly code") did what it said on the tin, but some of the older
CPU code omitted the default cache policy from their files. This
results in the kernel running with the caches disabled. Fix this
for ARM925.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A number of configurations spit out warnings similar to:
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_588369 which has unmet direct dependencies (CACHE_L2X0)
warning: (SOC_IMX6 && SOC_VF610 && ARCH_OMAP4) selects PL310_ERRATA_727915 which has unmet direct dependencies (CACHE_L2X0)
Clean up the dependencies here:
* PL310 symbols should only be selected when CACHE_L2X0 is enabled.
* Since the cache-l2x0 code detects PL310 presence at runtime, and we will
eventually get rid of CACHE_PL310, surround these errata options with an
if CACHE_L2X0 conditional rather than repeating the dependency against
each.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM updates from Russell King:
- Major clean-up of the L2 cache support code. The existing mess was
becoming rather unmaintainable through all the additions that others
have done over time. This turns it into a much nicer structure, and
implements a few performance improvements as well.
- Clean up some of the CP15 control register tweaks for alignment
support, moving some code and data into alignment.c
- DMA properties for ARM, from Santosh and reviewed by DT people. This
adds DT properties to specify bus translations we can't discover
automatically, and to indicate whether devices are coherent.
- Hibernation support for ARM
- Make ftrace work with read-only text in modules
- add suspend support for PJ4B CPUs
- rework interrupt masking for undefined instruction handling, which
allows us to enable interrupts earlier in the handling of these
exceptions.
- support for big endian page tables
- fix stacktrace support to exclude stacktrace functions from the
trace, and add save_stack_trace_regs() implementation so that kprobes
can record stack traces.
- Add support for the Cortex-A17 CPU.
- Remove last vestiges of ARM710 support.
- Removal of ARM "meminfo" structure, finally converting us solely to
memblock to handle the early memory initialisation.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (142 commits)
ARM: ensure C page table setup code follows assembly code (part II)
ARM: ensure C page table setup code follows assembly code
ARM: consolidate last remaining open-coded alignment trap enable
ARM: remove global cr_no_alignment
ARM: remove CPU_CP15 conditional from alignment.c
ARM: remove unused adjust_cr() function
ARM: move "noalign" command line option to alignment.c
ARM: provide common method to clear bits in CPU control register
ARM: 8025/1: Get rid of meminfo
ARM: 8060/1: mm: allow sub-architectures to override PCI I/O memory type
ARM: 8066/1: correction for ARM patch 8031/2
ARM: 8049/1: ftrace/add save_stack_trace_regs() implementation
ARM: 8065/1: remove last use of CONFIG_CPU_ARM710
ARM: 8062/1: Modify ldrt fixup handler to re-execute the userspace instruction
ARM: 8047/1: rwsem: use asm-generic rwsem implementation
ARM: l2c: trial at enabling some Cortex-A9 optimisations
ARM: l2c: add warnings for stuff modifying aux_ctrl register values
ARM: l2c: print a warning with L2C-310 caches if the cache size is modified
ARM: l2c: remove old .set_debug method
ARM: l2c: kill L2X0_AUX_CTRL_MASK before anyone else makes use of this
...
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"A few fixes for dma-mapping and CMA subsystems"
* 'for-v3.16' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
CMA: correct unlock target
drivers/base/dma-contiguous.c: erratum of dev_get_cma_area
arm: dma-mapping: add checking cma area initialized
arm: dma-iommu: Clean up redundant variable
cma: Remove potential deadlock situation
This does the same as the previous commit, but for the S bit, which also
needs to match the initial value which the assembly code used for the
same reasons. Again, we add a check for SMP to ensure that the page
tables are correctly setup for SMP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix a long standing bug where, for ARMv6+, we don't fully ensure that
the C code sets the same cache policy as the assembly code. This was
introduced partially by commit 11179d8ca2 ([ARM] 4497/1: Only allow
safe cache configurations on ARMv6 and later) and also by adding SMP
support.
This patch sets the default cache policy based on the flags used by the
assembly code, and then ensures that when a cache policy command line
argument is used, we verify that on ARMv6, it matches the initial setup.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cr_no_alignment is really only used by the alignment code. Since we no
longer change the setting of cr_alignment after boot, we can localise
this to alignment.c
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
alignment.c will not be built unless CPU_CP15 is set:
config CPU_CP15
bool
config CPU_CP15_MMU
bool
select CPU_CP15
config ALIGNMENT_TRAP
bool
depends on CPU_CP15_MMU
So there's no point having conditionals on CPU_CP15 within this code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
memblock is now fully integrated into the kernel and is the prefered
method for tracking memory. Rather than reinvent the wheel with
meminfo, migrate to using memblock directly instead of meminfo as
an intermediate.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to a design incompatibility between the PCIe Marvell controller
and the Cortex-A9, stressing PCIe devices with a lot of traffic
quickly causes a deadlock.
One part of the workaround for this is to have all PCIe regions mapped
as strongly-ordered (MT_UNCACHED) instead of the default
MT_DEVICE. While the arch_ioremap_caller() mechanism allows
sub-architecture code to override ioremap(), used to map PCIe memory
regions, there isn't such a mechanism to override the behavior of
pci_ioremap_io().
This commit adds the arch_pci_ioremap_mem_type variable, initialized
to MT_DEVICE by default, and that sub-architecture code can
override. We have chosen to expose a single variable rather than
offering the possibility of overriding the entire pci_ioremap_io(),
because implementing pci_ioremap_io() requires calling functions
(get_mem_type()) that are private to the arch/arm/mm/ code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we have now removed all instances of the L2C-310 having its cache
size "modified" via platform/SoC code, discourage new cases showing
up by printing a warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We no longer need or require the .set_debug method; we handle everything
it used to do via the .write_sec method instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a common assembly implementation for PL310 resume code. Certain
platforms need to re-initialise the L2C cache early as it may preserve
data across a S2RAM cycle, and therefore must be enabled along with the
L1 cache and MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we always write to these during the cache initialisation, it is
a good idea to always have the non-secure access bit set. Set it in
core code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AXI bus protocol requires that a write response should only be
sent back to the master when the last write has been accepted. Early
BRESP allows the L2C-310 to send the write response as soon as the
store buffer accepts the write address.
Cortex-A9 processors can signal to the L2C-310 that they wish to be
notified early, and if this optimisation is enabled, the L2C-310 can
signal an early write response.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the L2 cache register saving to a more sensible location - after
the cache has been enabled, and fixups have been run. We move the
saving of the auxiliary control register into the ->save function as
well which makes everything operate in a sane and maintainable way.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a mixture of different devices with different register layouts,
but we group all the bits together in an opaque mess. Split them out
into those which are L2C-310 specific and ones which refer to earlier
devices. Provide full auxiliary control register definitions.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having SoCs work around L2C erratum themselves, move them
into core code. This erratum affects the double linefill feature which
needs to be disabled for r3p0 to r3p1-50rel0.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When Linux is running in the non-secure world, any write to a secure
L2C register will generate an abort. Platforms normally have to call
firmware to work around this. Provide a hook for them to intercept
any L2C secure register write.
l2c_write_sec() avoids writes to secure registers which are already set
to the appropriate value, thus avoiding the overhead of needlessly
calling into the secure monitor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the L2C-310 errata configuration options to arch/arm/mm/Kconfig
along side the option which enables support for this device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the way size calculation data (base of way size) out of the
switch statement into the provided initialisation data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than assuming these are always 8-way, it can be decoded from the
auxillary register in the same manner as L2C-210.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than decoding this from the ID register, store it in the
l2c_init_data structure. This simplifies things some more, and
allows us to better provide further details as to how we're
driving the cache. We print the cache ID value anyway should we
need to precisely identify the cache hardware.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
non-OF initialisation has never been used with any cache controller
which isn't an ARM cache controller, so we can safely get rid of the
old (and buggy) l2x0_*-based operations structure.
This is also the last reference to:
- l2x0_clean_line()
- l2x0_inv_line()
- l2x0_flush_line()
- l2x0_flush_all()
- l2x0_clean_all()
- l2x0_inv_all()
- l2x0_inv_range()
- l2x0_clean_range()
- l2x0_flush_range()
- l2x0_enable()
- l2x0_resume()
so kill those functions too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Broadcom L2C-310 devices use ARMs L2C-310 R2P3 or later. These
require no errata workarounds, and so we can directly call the l2c210
functions from their methods.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The L2C-220 is different from the L2C-210 and L2C-310 in that every
operation is a background operation: this means we have to use
spinlocks to protect all operations, and we have to wait for every
operation to complete.
Should a second operation be attempted while a previous operation
is in progress, the response will be an imprecise abort.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where no errata affect the L2C-310 handlers, they are functionally
equivalent to L2C-210. Re-use the L2C-210 handlers for the L2C-310
part.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement L2C-310 erratum 588369 by overriding the invalidate range
and flush range methods in the outer_cache operations structure.
This allows us to sensibly contain the erratum code in one place
without affecting other locations/implemetations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement L2C-310 erratum 727915 by overriding the flush_all method
in the outer_cache operations structure. This allows us to sensibly
contain the erratum code in one place without affecting other
locations or implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add L2C-210 specific cache operation handlers. These are tailored to
the requirements of the L2C-210 cache controller, which doesn't
require any workarounds. We avoid using the way operations during
normal operation, which means we can avoid locking: the only time
we use the way operations are during initialisation, and when
disabling the cache.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the pl310_set_debug() into the l2c-310 code area, and don't hide
it with ifdefs. Rename it to l2c310_set_debug().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The l2x0 unlocking code is only called from l2x0_enable() now, so move
the logic entirely into that function and simplify it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename the pl310 save/resume functions to have a l2c310 prefix - this
is it's official name. Use a local cached copy of the l2x0_base
virtual address, and also realise that many of the resume function
tails are the same as the enable functions, so make a call to the
enable function instead of duplicating that code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the save/resume code hooks to the non-OF implementations as well.
There's no reason for the non-OF implementations to be any different
from the OF implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than putting quirk handling in __l2c_init(), move it out to a
separate function which individual implementations can specify. This
helps to localise the quirks to those implementations which require
them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King