Reported by Stefanos Harhalakis; although 2.6.27-rc1 talks to itself using IPv6
TCP MD5 packets just fine, Stefanos noted that tcpdump claimed that the
signatures were invalid.
I broke this in 49a72dfb88 ("tcp: Fix MD5
signatures for non-linear skbs"), it was just a typo.
Note that tcpdump will still sometimes claim that the signatures are incorrect.
A patch to tcpdump has been submitted for this[1].
[1] http://tinyurl.com/6a4fl2
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix:
net/ipv4/route.c: In function 'ip_static_sysctl_init':
net/ipv4/route.c:3225: error: 'ipv4_route_path' undeclared (first use in this function)
net/ipv4/route.c:3225: error: (Each undeclared identifier is reported only once
net/ipv4/route.c:3225: error: for each function it appears in.)
net/ipv4/route.c:3225: error: 'ipv4_route_table' undeclared (first use in this function)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed, looking at tcpdumps, that timewait ACKs were getting sent
with an incorrect MD5 signature when signatures were enabled.
I broke this in 49a72dfb88 ("tcp: Fix
MD5 signatures for non-linear skbs"). I didn't take into account that
the skb passed to tcp_*_send_ack was the inbound packet, thus the
source and dest addresses need to be swapped when calculating the MD5
pseudoheader.
Signed-off-by: Adam Langley <agl@imperialviolet.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP used ip6_xmit() to send fragments after received ICMP packet too
big message. But while send packet used ip6_xmit, the skb->local_df is
not initialized. So when skb if enter ip6_fragment(), the following
code will discard the skb.
ip6_fragment(...)
{
if (!skb->local_df) {
...
return -EMSGSIZE;
}
...
}
SCTP do the following step:
1. send packet ip6_xmit(skb, ipfragok=0)
2. received ICMP packet too big message
3. if PMTUD_ENABLE: ip6_xmit(skb, ipfragok=1)
This patch fixed the problem by set local_df if ipfragok is true.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Deleting a timer with del_timer doesn't guarantee, that the
timer function is not running at the moment of deletion. Thus
in the xt_hashlimit case we can get into a ticklish situation
when the htable_gc rearms the timer back and we'll actually
delete an entry with a pending timer.
Fix it with using del_timer_sync().
AFAIK del_timer_sync checks for the timer to be pending by
itself, so I remove the check.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The thing is that recent_mt_destroy first flushes the entries
from table with the recent_table_flush and only *after* this
removes the proc file, corresponding to that table.
Thus, if we manage to write to this file the '+XXX' command we
will leak some entries. If we manage to write there a 'clean'
command we'll race in two recent_table_flush flows, since the
recent_mt_destroy calls this outside the recent_lock.
The proper solution as I see it is to remove the proc file first
and then go on with flushing the table. This flushing becomes
safe w/o the lock, since the table is already inaccessible from
the outside.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to time out dead connections quicker, keep track of outstanding data
and cap the timeout.
Suggested by Herbert Xu.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix const assignment/discard warnings in the ATM networking driver.
The lane2_assoc_ind() function needed its arguments changing to match changes
in the lane2_ops struct (patch 61c33e0129
"atm: use const where reasonable").
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bridging interfaces with different MTUs, the bridge correctly chooses
the minimum of the MTUs of the physical devices as the bridges MTU. But
when a frame is passed which fits through the incoming, but not through
the outgoing interface, a "Fragmentation Needed" packet is generated.
However, the propagated MTU is hardcoded to 1500, which is wrong in this
situation. The sender will repeat the packet again with the same frame
size, and the same problem will occur again.
Instead of sending 1500, the (correct) MTU value of the bridge is now sent
via PMTU. To achieve this, the corresponding rtable structure is stored
in its net_bridge structure.
Modified to get rid of fake_net_device as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a menuconfig directive to make all of networking support one-click
deselectable from the top-level menu.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This call is no longer needed, sockstat6 is per namespace so it is
removed at the namespace subsystem destruction.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug report from Steven Jan Springl:
Issuing the following command causes a kernel oops:
tc qdisc add dev eth0 handle ffff: ingress
The problem mostly stems from all of the special case handling of
ingress qdiscs.
So, to fix this, do the grafting operation the same way we do for TX
qdiscs. Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.
Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL. There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error occured, datagram_send_ctl() should exit immediately rather than
continue to run the for loop. Otherwise, the variable err might be changed and
the error might be hidden.
Fix this bug by using "goto" instead of "break".
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes mesh beaconing, which was broken by "mac80211: revamp
beacon configuration".
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The master interface is a virtual interface that is registered
to mac80211, changing that does not seem like a good idea at
the moment. However, since it has no sdata, we cannot accept
any configuration for it. This patch makes the cfg80211 hooks
reject any such attempt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julius Volz pointed out that the dump callbacks in nl80211 were
broken and fixed one of them. This patch fixes the other three
and also addresses the TODOs there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Julius Volz <juliusv@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In net/mac80211/tx.c, there are some #ifdef which checks
MAC80211_VERBOSE_PS_DEBUG
(which in fact is never set) instead of
CONFIG_MAC80211_VERBOSE_PS_DEBUG, as should be.
This patch replaces MAC80211_VERBOSE_PS_DEBUG with
CONFIG_MAC80211_VERBOSE_PS_DEBUG in these #ifdef commands in
net/mac80211/tx.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Return the proper error code rather than a hard-coded ENOMEM from
ieee80211_wep_init. Also, print the error code on failure.
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use dev_kfree_skb_any(); instead of dev_kfree_skb();, since
ieee80211_beacon_get function might be called from atomic.
(It's in a fail path.)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some stupid reason, I sent and old version of the patch minor kernel
doc-fix patch, and it got merged before I noticed the problem. This is an
incremental fix on top.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two mutexes in rfkill:
rfkill->mutex, which protects some of the fields of a rfkill struct, and is
also used for callback serialization.
rfkill_mutex, which protects the global state, the list of registered
rfkill structs and rfkill->claim.
Make sure to use the correct mutex, and to not miss locking rfkill->mutex
even when we already took rfkill_mutex.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill needs to unregister the led trigger AFTER a call to
rfkill_remove_switch(), otherwise it will not update the LED state,
possibly leaving it ON when it should be OFF.
To make led-trigger unregistering safer, guard against unregistering a
trigger twice, and also against issuing trigger events to a led trigger
that was unregistered. This makes the error unwind paths more resilient.
Refer to "rfkill: Register LED triggers before registering switch".
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the rfkill class does work with just get_state(), it doesn't work
well on devices that are subject to external events that cause rfkill state
changes.
Document that rfkill_force_state() is required in those cases.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Piss-poor sysctl registration API strikes again, film at 11...
What we really need is _pathname_ required to be present in already
registered table, so that kernel could warn about bad order. That's the
next target for sysctl stuff (and generally saner and more explicit
order of initialization of ipv[46] internals wouldn't hurt either).
For the time being, here are full fixups required by ..._rotable()
stuff; we make per-net sysctl sets descendents of "ro" one and make sure
that sufficient skeleton is there before we start registering per-net
sysctls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Piss-poor sysctl registration API strikes again, film at 11...
What we really need is _pathname_ required to be present in
already registered table, so that kernel could warn about bad
order. That's the next target for sysctl stuff (and generally
saner and more explicit order of initialization of ipv[46]
internals wouldn't hurt either).
For the time being, here are full fixups required by ..._rotable()
stuff; we make per-net sysctl sets descendents of "ro" one and
make sure that sufficient skeleton is there before we start registering
per-net sysctls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/ipcomp.c: In function ‘ipcomp4_init_state’:
net/ipv4/ipcomp.c:109: warning: unused variable ‘calg_desc’
net/ipv4/ipcomp.c:108: warning: unused variable ‘ipcd’
net/ipv4/ipcomp.c:107: warning: ‘err’ may be used uninitialized in this function
net/ipv6/ipcomp6.c: In function ‘ipcomp6_init_state’:
net/ipv6/ipcomp6.c:139: warning: unused variable ‘calg_desc’
net/ipv6/ipcomp6.c:138: warning: unused variable ‘ipcd’
net/ipv6/ipcomp6.c:137: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (39 commits)
[PATCH] fix RLIM_NOFILE handling
[PATCH] get rid of corner case in dup3() entirely
[PATCH] remove remaining namei_{32,64}.h crap
[PATCH] get rid of indirect users of namei.h
[PATCH] get rid of __user_path_lookup_open
[PATCH] f_count may wrap around
[PATCH] dup3 fix
[PATCH] don't pass nameidata to __ncp_lookup_validate()
[PATCH] don't pass nameidata to gfs2_lookupi()
[PATCH] new (local) helper: user_path_parent()
[PATCH] sanitize __user_walk_fd() et.al.
[PATCH] preparation to __user_walk_fd cleanup
[PATCH] kill nameidata passing to permission(), rename to inode_permission()
[PATCH] take noexec checks to very few callers that care
Re: [PATCH 3/6] vfs: open_exec cleanup
[patch 4/4] vfs: immutable inode checking cleanup
[patch 3/4] fat: dont call notify_change
[patch 2/4] vfs: utimes cleanup
[patch 1/4] vfs: utimes: move owner check into inode_change_ok()
[PATCH] vfs: use kstrdup() and check failing allocation
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
make it atomic_long_t; while we are at it, get rid of useless checks in affs,
hfs and hpfs - ->open() always has it equal to 1, ->release() - to 0.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Massage ipv4 initialization - make sure that net.ipv4 appears as
non-per-net-namespace before it shows up in per-net-namespace sysctls.
That's the only change outside of sysctl.c needed to get sane ordering
rules and data structures for sysctls (esp. for procfs side of that
mess).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
New object: set of sysctls [currently - root and per-net-ns].
Contains: pointer to parent set, list of tables and "should I see this set?"
method (->is_seen(set)).
Current lists of tables are subsumed by that; net-ns contains such a beast.
->lookup() for ctl_table_root returns pointer to ctl_table_set instead of
that to ->list of that ctl_table_set.
[folded compile fixes by rdd for configs without sysctl]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Running recent kernels, and using a particular vpn gateway, I've been
having to edit my mails down to get them accepted by the smtp server.
Git bisect led to commit e84f84f276 -
netns: place rt_genid into struct net. The conversion from a != test
to rt_is_expired() put one negative too many: and now my mail works.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Linus points out, "ct->ext" and "new" are always equal, avoid unnecessary
dereferences and use "new" directly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Patrick McHardy, introduce a __krealloc() that doesn't
free the original buffer to fix a double-free and use-after-free bug
introduced by me in netfilter that uses RCU.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Tested-by: Dieter Ries <clip2@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IN, FORWARD -- grab netns from in device, OUT -- from out device.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently not visible, because NET_NS is mutually exclusive with SYSFS
which is required by SECURITY.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Replace previous instances of the cpumask_of_cpu_ptr* macros
with a the new (lvalue capable) generic cpumask_of_cpu().
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds a minimum-length check for ICMPv6 packets, as per the previous
patch for ICMPv4 payloads.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Unlike TCP, which only needs 8 octets of original packet data, DCCP requires
minimally 12 or 16 bytes for ICMP-payload sequence number checks.
This patch replaces the insufficient length constant of 8 with a two-stage
test, making sure that 12 bytes are available, before computing the basic
header length required for sequence number checks.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This adds a sequence number check for ICMPv6 DCCP error packets, in the same
manner as it has been done for ICMPv4 in the previous patch.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The payload of ICMP message is a part of the packet sent by ourself,
so the sequence number check must use AWL and AWH, not SWL and SWH.
For example:
Endpoint A Endpoint B
DATA-ACK -------->
(SEQ=X)
<-------- ICMP (Fragmentation Needed)
(SEQ=X)
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The AWL lower Ack validity window advances in proportion to GSS, the greatest
sequence number sent. Updating AWL other than at connection setup (in the
DCCP-Request sent by dccp_v{4,6}_connect()) was missing in the DCCP code.
This bug lead to syslog messages such as
"kernel: dccp_check_seqno: DCCP: Step 6 failed for DATAACK packet, [...]
P.ackno exists or LAWL(82947089) <= P.ackno(82948208)
<= S.AWH(82948728), sending SYNC..."
The difference between AWL/AWH here is 1639 packets, while the expected value
(the Sequence Window) would have been 100 (the default). A closer look showed
that LAWL = AWL = 82947089 equalled the ISS on the Response.
The patch now updates AWL with each increase of GSS.
Further changes:
----------------
The patch also enforces more stringent checks on the ISS sequence number:
* AWL is initialised to ISS at connection setup and remains at this value;
* AWH is then always set to GSS (via dccp_update_gss());
* so on the first Request: AWL = AWH = ISS,
and on the n-th Request: AWL = ISS, AWH = ISS + n.
As a consequence, only Response packets that refer to Requests sent by this
host will pass, all others are discarded. This is the intention and in effect
implements the initial adjustments for AWL as specified in RFC 4340, 7.5.1.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This patch allows the sender to distinguish original and retransmitted packets,
which is in particular needed for the retransmission of DCCP-Requests:
* the first Request uses ISS (generated in net/dccp/ip*.c), and sets GSS = ISS;
* all retransmitted Requests use GSS' = GSS + 1, so that the n-th retransmitted
Request has sequence number ISS + n (mod 48).
To add generic support, the patch reorganises existing code so that:
* icsk_retransmits == 0 for the original packet and
* icsk_retransmits = n > 0 for the n-th retransmitted packet
at the time dccp_transmit_skb() is called, via dccp_retransmit_skb().
Thanks to Wei Yongjun for pointing this problem out.
Further changes:
----------------
* removed the `skb' argument from dccp_retransmit_skb(), since sk_send_head
is used for all retransmissions (the exception is client-Acks in PARTOPEN
state, but these do not use sk_send_head);
* since sk_send_head always contains the original skb (via dccp_entail()),
skb_cloned() never evaluated to true and thus pskb_copy() was never used.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This reverts commit f867e6af94.
Based upon discussions between Jarek and Patrick McHardy
this is field being set is more a config parameter than a
statistic. And we should add a true statistic to provide
this information if we really want it.
Signed-off-by: David S. Miller <davem@davemloft.net>
ecn_ok is not initialized when a connection is established by cookies.
The cookie syn-ack never sets ECN, so ecn_ok must be set to 0.
Spotted using ns-3/network simulation cradle simulator and valgrind.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the permission check for networking sysctl's to allow modification
when current process has CAP_NET_ADMIN capability and is not root. This
version uses the until now unused permissions hook to override the mode
value for /proc/sys/net if accessed by a user with capabilities.
Found while working with Quagga. It is impossible to turn forwarding
on/off through the command interface because Quagga uses secure coding
practice of dropping privledges during initialization and only raising via
capabilities when necessary. Since the dameon has reset real/effective
uid after initialization, all attempts to access /proc/sys/net variables
will fail.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morgan <morgan@kernel.org>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All ratelimit user use same jiffies and burst params, so some messages
(callbacks) will be lost.
For example:
a call printk_ratelimit(5 * HZ, 1)
b call printk_ratelimit(5 * HZ, 1) before the 5*HZ timeout of a, then b will
will be supressed.
- rewrite __ratelimit, and use a ratelimit_state as parameter. Thanks for
hints from andrew.
- Add WARN_ON_RATELIMIT, update rcupreempt.h
- remove __printk_ratelimit
- use __ratelimit in net_ratelimit
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All uses of list_for_each_rcu() can be profitably replaced by the
easier-to-use list_for_each_entry_rcu(). This patch makes this change for
networking, in preparation for removing the list_for_each_rcu() API
entirely.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When decompressing extremely large packets allocating them through
kmalloc is prone to failure. Therefore it's better to use page
frags instead.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch merges the IPv4/IPv6 IPComp implementations since most
of the code is identical. As a result future enhancements will no
longer need to be duplicated.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pkt_sched: sch_sfq: dump a real number of flows
atm: [fore200e] use MODULE_FIRMWARE() and other suggested cleanups
netfilter: make security table depend on NETFILTER_ADVANCED
tcp: Clear probes_out more aggressively in tcp_ack().
e1000e: fix e1000_netpoll(), remove extraneous e1000_clean_tx_irq() call
net: Update entry in af_family_clock_key_strings
netdev: Remove warning from __netif_schedule().
sky2: don't stop queue on shutdown
This patch adds test that ensure the boundary conditions for the various
constants introduced in the previous patches is met. No code is generated.
[akpm@linux-foundation.org: fix alpha]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some platforms do not have support to restore the signal mask in the
return path from a syscall. For those platforms syscalls like pselect are
not defined at all. This is, I think, not a good choice for paccept()
since paccept() adds more value on top of accept() than just the signal
mask handling.
Therefore this patch defines a scaled down version of the sys_paccept
function for those platforms. It returns -EINVAL in case the signal mask
is non-NULL but behaves the same otherwise.
Note that I explicitly included <linux/thread_info.h>. I saw that it is
currently included but indirectly two levels down. There is too much risk
in relying on this. The header might change and then suddenly the
function definition would change without anyone immediately noticing.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is by far the most complex in the series. It adds a new syscall
paccept. This syscall differs from accept in that it adds (at the userlevel)
two additional parameters:
- a signal mask
- a flags value
The flags parameter can be used to set flag like SOCK_CLOEXEC. This is
imlpemented here as well. Some people argued that this is a property which
should be inherited from the file desriptor for the server but this is against
POSIX. Additionally, we really want the signal mask parameter as well
(similar to pselect, ppoll, etc). So an interface change in inevitable.
The flag value is the same as for socket and socketpair. I think diverging
here will only create confusion. Similar to the filesystem interfaces where
the use of the O_* constants differs, it is acceptable here.
The signal mask is handled as for pselect etc. The mask is temporarily
installed for the thread and removed before the call returns. I modeled the
code after pselect. If there is a problem it's likely also in pselect.
For architectures which use socketcall I maintained this interface instead of
adding a system call. The symmetry shouldn't be broken.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <errno.h>
#include <fcntl.h>
#include <pthread.h>
#include <signal.h>
#include <stdio.h>
#include <unistd.h>
#include <netinet/in.h>
#include <sys/socket.h>
#include <sys/syscall.h>
#ifndef __NR_paccept
# ifdef __x86_64__
# define __NR_paccept 288
# elif defined __i386__
# define SYS_PACCEPT 18
# define USE_SOCKETCALL 1
# else
# error "need __NR_paccept"
# endif
#endif
#ifdef USE_SOCKETCALL
# define paccept(fd, addr, addrlen, mask, flags) \
({ long args[6] = { \
(long) fd, (long) addr, (long) addrlen, (long) mask, 8, (long) flags }; \
syscall (__NR_socketcall, SYS_PACCEPT, args); })
#else
# define paccept(fd, addr, addrlen, mask, flags) \
syscall (__NR_paccept, fd, addr, addrlen, mask, 8, flags)
#endif
#define PORT 57392
#define SOCK_CLOEXEC O_CLOEXEC
static pthread_barrier_t b;
static void *
tf (void *arg)
{
pthread_barrier_wait (&b);
int s = socket (AF_INET, SOCK_STREAM, 0);
struct sockaddr_in sin;
sin.sin_family = AF_INET;
sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK);
sin.sin_port = htons (PORT);
connect (s, (const struct sockaddr *) &sin, sizeof (sin));
close (s);
pthread_barrier_wait (&b);
s = socket (AF_INET, SOCK_STREAM, 0);
sin.sin_port = htons (PORT);
connect (s, (const struct sockaddr *) &sin, sizeof (sin));
close (s);
pthread_barrier_wait (&b);
pthread_barrier_wait (&b);
sleep (2);
pthread_kill ((pthread_t) arg, SIGUSR1);
return NULL;
}
static void
handler (int s)
{
}
int
main (void)
{
pthread_barrier_init (&b, NULL, 2);
struct sockaddr_in sin;
pthread_t th;
if (pthread_create (&th, NULL, tf, (void *) pthread_self ()) != 0)
{
puts ("pthread_create failed");
return 1;
}
int s = socket (AF_INET, SOCK_STREAM, 0);
int reuse = 1;
setsockopt (s, SOL_SOCKET, SO_REUSEADDR, &reuse, sizeof (reuse));
sin.sin_family = AF_INET;
sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK);
sin.sin_port = htons (PORT);
bind (s, (struct sockaddr *) &sin, sizeof (sin));
listen (s, SOMAXCONN);
pthread_barrier_wait (&b);
int s2 = paccept (s, NULL, 0, NULL, 0);
if (s2 < 0)
{
puts ("paccept(0) failed");
return 1;
}
int coe = fcntl (s2, F_GETFD);
if (coe & FD_CLOEXEC)
{
puts ("paccept(0) set close-on-exec-flag");
return 1;
}
close (s2);
pthread_barrier_wait (&b);
s2 = paccept (s, NULL, 0, NULL, SOCK_CLOEXEC);
if (s2 < 0)
{
puts ("paccept(SOCK_CLOEXEC) failed");
return 1;
}
coe = fcntl (s2, F_GETFD);
if ((coe & FD_CLOEXEC) == 0)
{
puts ("paccept(SOCK_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (s2);
pthread_barrier_wait (&b);
struct sigaction sa;
sa.sa_handler = handler;
sa.sa_flags = 0;
sigemptyset (&sa.sa_mask);
sigaction (SIGUSR1, &sa, NULL);
sigset_t ss;
pthread_sigmask (SIG_SETMASK, NULL, &ss);
sigaddset (&ss, SIGUSR1);
pthread_sigmask (SIG_SETMASK, &ss, NULL);
sigdelset (&ss, SIGUSR1);
alarm (4);
pthread_barrier_wait (&b);
errno = 0 ;
s2 = paccept (s, NULL, 0, &ss, 0);
if (s2 != -1 || errno != EINTR)
{
puts ("paccept did not fail with EINTR");
return 1;
}
close (s);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: make it compile]
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for flag values which are ORed to the type passwd
to socket and socketpair. The additional code is minimal. The flag
values in this implementation can and must match the O_* flags. This
avoids overhead in the conversion.
The internal functions sock_alloc_fd and sock_map_fd get a new parameters
and all callers are changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <netinet/in.h>
#include <sys/socket.h>
#define PORT 57392
/* For Linux these must be the same. */
#define SOCK_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd;
fd = socket (PF_INET, SOCK_STREAM, 0);
if (fd == -1)
{
puts ("socket(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("socket(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = socket (PF_INET, SOCK_STREAM|SOCK_CLOEXEC, 0);
if (fd == -1)
{
puts ("socket(SOCK_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("socket(SOCK_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (fd);
int fds[2];
if (socketpair (PF_UNIX, SOCK_STREAM, 0, fds) == -1)
{
puts ("socketpair(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
coe = fcntl (fds[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("socketpair(0) set close-on-exec flag for fds[%d]\n", i);
return 1;
}
close (fds[i]);
}
if (socketpair (PF_UNIX, SOCK_STREAM|SOCK_CLOEXEC, 0, fds) == -1)
{
puts ("socketpair(SOCK_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
coe = fcntl (fds[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("socketpair(SOCK_CLOEXEC) does not set close-on-exec flag for fds[%d]\n", i);
return 1;
}
close (fds[i]);
}
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dump the "flows" number according to the number of active flows
instead of repeating the "limit".
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
This is based upon an excellent bug report from Eric Dumazet.
tcp_ack() should clear ->icsk_probes_out even if there are packets
outstanding. Otherwise if we get a sequence of ACKs while we do have
packets outstanding over and over again, we'll never clear the
probes_out value and eventually think the connection is too sick and
we'll reset it.
This appears to be some "optimization" added to tcp_ack() in the 2.4.x
timeframe. In 2.2.x, probes_out is pretty much always cleared by
tcp_ack().
Here is Eric's original report:
----------------------------------------
Apparently, we can in some situations reset TCP connections in a couple of seconds when some frames are lost.
In order to reproduce the problem, please try the following program on linux-2.6.25.*
Setup some iptables rules to allow two frames per second sent on loopback interface to tcp destination port 12000
iptables -N SLOWLO
iptables -A SLOWLO -m hashlimit --hashlimit 2 --hashlimit-burst 1 --hashlimit-mode dstip --hashlimit-name slow2 -j ACCEPT
iptables -A SLOWLO -j DROP
iptables -A OUTPUT -o lo -p tcp --dport 12000 -j SLOWLO
Then run the attached program and see the output :
# ./loop
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,1)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,3)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,5)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,7)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,9)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,200ms,11)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,201ms,13)
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 40 127.0.0.1:54455 127.0.0.1:12000 timer:(persist,188ms,15)
write(): Connection timed out
wrote 890 bytes but was interrupted after 9 seconds
ESTAB 0 0 127.0.0.1:12000 127.0.0.1:54455
Exiting read() because no data available (4000 ms timeout).
read 860 bytes
While this tcp session makes progress (sending frames with 50 bytes of payload, every 500ms), linux tcp stack decides to reset it, when tcp_retries 2 is reached (default value : 15)
tcpdump :
15:30:28.856695 IP 127.0.0.1.56554 > 127.0.0.1.12000: S 33788768:33788768(0) win 32792 <mss 16396,nop,nop,sackOK,nop,wscale 7>
15:30:28.856711 IP 127.0.0.1.12000 > 127.0.0.1.56554: S 33899253:33899253(0) ack 33788769 win 32792 <mss 16396,nop,nop,sackOK,nop,wscale 7>
15:30:29.356947 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 1:61(60) ack 1 win 257
15:30:29.356966 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 61 win 257
15:30:29.866415 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 61:111(50) ack 1 win 257
15:30:29.866427 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 111 win 257
15:30:30.366516 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 111:161(50) ack 1 win 257
15:30:30.366527 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 161 win 257
15:30:30.876196 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 161:211(50) ack 1 win 257
15:30:30.876207 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 211 win 257
15:30:31.376282 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 211:261(50) ack 1 win 257
15:30:31.376290 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 261 win 257
15:30:31.885619 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 261:311(50) ack 1 win 257
15:30:31.885631 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 311 win 257
15:30:32.385705 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 311:361(50) ack 1 win 257
15:30:32.385715 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 361 win 257
15:30:32.895249 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 361:411(50) ack 1 win 257
15:30:32.895266 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 411 win 257
15:30:33.395341 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 411:461(50) ack 1 win 257
15:30:33.395351 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 461 win 257
15:30:33.918085 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 461:511(50) ack 1 win 257
15:30:33.918096 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 511 win 257
15:30:34.418163 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 511:561(50) ack 1 win 257
15:30:34.418172 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 561 win 257
15:30:34.927685 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 561:611(50) ack 1 win 257
15:30:34.927698 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 611 win 257
15:30:35.427757 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 611:661(50) ack 1 win 257
15:30:35.427766 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 661 win 257
15:30:35.937359 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 661:711(50) ack 1 win 257
15:30:35.937376 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 711 win 257
15:30:36.437451 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 711:761(50) ack 1 win 257
15:30:36.437464 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 761 win 257
15:30:36.947022 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 761:811(50) ack 1 win 257
15:30:36.947039 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 811 win 257
15:30:37.447135 IP 127.0.0.1.56554 > 127.0.0.1.12000: P 811:861(50) ack 1 win 257
15:30:37.447203 IP 127.0.0.1.12000 > 127.0.0.1.56554: . ack 861 win 257
15:30:41.448171 IP 127.0.0.1.12000 > 127.0.0.1.56554: F 1:1(0) ack 861 win 257
15:30:41.448189 IP 127.0.0.1.56554 > 127.0.0.1.12000: R 33789629:33789629(0) win 0
Source of program :
/*
* small producer/consumer program.
* setup a listener on 127.0.0.1:12000
* Forks a child
* child connect to 127.0.0.1, and sends 10 bytes on this tcp socket every 100 ms
* Father accepts connection, and read all data
*/
#include <sys/types.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <unistd.h>
#include <stdio.h>
#include <time.h>
#include <sys/poll.h>
int port = 12000;
char buffer[4096];
int main(int argc, char *argv[])
{
int lfd = socket(AF_INET, SOCK_STREAM, 0);
struct sockaddr_in socket_address;
time_t t0, t1;
int on = 1, sfd, res;
unsigned long total = 0;
socklen_t alen = sizeof(socket_address);
pid_t pid;
time(&t0);
socket_address.sin_family = AF_INET;
socket_address.sin_port = htons(port);
socket_address.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
if (lfd == -1) {
perror("socket()");
return 1;
}
setsockopt(lfd, SOL_SOCKET, SO_REUSEADDR, &on, sizeof(int));
if (bind(lfd, (struct sockaddr *)&socket_address, sizeof(socket_address)) == -1) {
perror("bind");
close(lfd);
return 1;
}
if (listen(lfd, 1) == -1) {
perror("listen()");
close(lfd);
return 1;
}
pid = fork();
if (pid == 0) {
int i, cfd = socket(AF_INET, SOCK_STREAM, 0);
close(lfd);
if (connect(cfd, (struct sockaddr *)&socket_address, sizeof(socket_address)) == -1) {
perror("connect()");
return 1;
}
for (i = 0 ; ;) {
res = write(cfd, "blablabla\n", 10);
if (res > 0) total += res;
else if (res == -1) {
perror("write()");
break;
} else break;
usleep(100000);
if (++i == 10) {
system("ss -on dst 127.0.0.1:12000");
i = 0;
}
}
time(&t1);
fprintf(stderr, "wrote %lu bytes but was interrupted after %g seconds\n", total, difftime(t1, t0));
system("ss -on | grep 127.0.0.1:12000");
close(cfd);
return 0;
}
sfd = accept(lfd, (struct sockaddr *)&socket_address, &alen);
if (sfd == -1) {
perror("accept");
return 1;
}
close(lfd);
while (1) {
struct pollfd pfd[1];
pfd[0].fd = sfd;
pfd[0].events = POLLIN;
if (poll(pfd, 1, 4000) == 0) {
fprintf(stderr, "Exiting read() because no data available (4000 ms timeout).\n");
break;
}
res = read(sfd, buffer, sizeof(buffer));
if (res > 0) total += res;
else if (res == 0) break;
else perror("read()");
}
fprintf(stderr, "read %lu bytes\n", total);
close(sfd);
return 0;
}
----------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
In the merge phase of the CAN subsystem the
af_family_clock_key_strings[] have been added to sock.c in commit
443aef0edd
(lockdep: fixup sk_callback_lock annotation). This trivial patch adds
the missing name for address family 29 (AF_CAN).
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
It isn't helping anything and we aren't going to be able to change all
the drivers that do queue wakeups in strange situations.
Just letting a noop_qdisc get scheduled will work because when
qdisc_run() executes via net_tx_work() it will simply find no packets
pending when it makes the ->dequeue() call in qdisc_restart.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (82 commits)
ipw2200: Call netif_*_queue() interfaces properly.
netxen: Needs to include linux/vmalloc.h
[netdrvr] atl1d: fix !CONFIG_PM build
r6040: rework init_one error handling
r6040: bump release number to 0.18
r6040: handle RX fifo full and no descriptor interrupts
r6040: change the default waiting time
r6040: use definitions for magic values in descriptor status
r6040: completely rework the RX path
r6040: call napi_disable when puting down the interface and set lp->dev accordingly.
mv643xx_eth: fix NETPOLL build
r6040: rework the RX buffers allocation routine
r6040: fix scheduling while atomic in r6040_tx_timeout
r6040: fix null pointer access and tx timeouts
r6040: prefix all functions with r6040
rndis_host: support WM6 devices as modems
at91_ether: use netstats in net_device structure
sfc: Create one RX queue and interrupt per CPU package by default
sfc: Use a separate workqueue for resets
sfc: I2C adapter initialisation fixes
...
I/OAT DMA performance tuning showed different optimal values of
tcp_dma_copybreak for different I/OAT versions (4096 for 1.2 and 2048
for 2.0). This patch lets ioatdma driver set tcp_dma_copybreak value
according to these results.
[dan.j.williams@intel.com: remove some ifdefs]
Signed-off-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Change icmp6_dst_gc to return the one value the caller cares about rather
than using call by reference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Th fib_table_hash is an array, so use kcalloc.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now there is spin_trylock_bh, use it rather than open coding.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This timer normally happens once a minute, there is no need to cause an
early wakeup for it, so align it to next second boundary to safe power.
It can't be deferred because then it could take too long on cleanup or DoS.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIB timer list is a trivial size structure, avoid indirection and just
put it in existing ns.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 20c2c1fd6c
(sctp: add sctp/remaddr table to complete RFC remote address table OID)
added an unused sctp_assoc_proc_exit() function that seems to have been
unintentionally created when copying the assocs code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_outq_flush() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the needlessly global qdisc_class_hash_alloc() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
The function header comments have to go with the functions
they are documenting, or things go horribly wrong when we
try to process them with the docbook tools.
Warning(include/linux/netdevice.h:1006): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1033): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1067): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1093): No description found for parameter 'dev_queue'
Warning(include/linux/netdevice.h:1474): No description found for parameter 'txq'
Error(net/core/dev.c:1674): cannot understand prototype: 'u32 simple_tx_hashrnd; '
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't create symlinks in a class to a device that is not owned by the
class. If the bluetooth subsystem really wants to point to all of the
devices it controls, it needs to create real devices, not fake symlinks.
Cc: Maxim Krasnyansky <maxk@qualcomm.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported by Alexey Dobriyan:
CHECK net/ipv4/tcp_output.c
net/ipv4/tcp_output.c:475:7: warning: dubious: !x & y
And sparse is damn right!
if (unlikely(!OPTION_TS & opts->options))
^^^
size += TCPOLEN_SACKPERM_ALIGNED;
OPTION_TS is (1 << 1), so condition will never trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clamps the cscov setsockopt values to a maximum of 0xFFFF.
Setsockopt values greater than 0xffff can cause an unwanted
wrap-around. Further, IPv6 jumbograms are not supported (RFC 3838,
3.5), so that values greater than 0xffff are not even useful.
Further changes: fixed a typo in the documentation.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Dave:
This patch adds a function to get the driver name from a struct net_device,
and consequently uses this in the watchdog timeout handler to print as
part of the message.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor nit, use size_t for allocation size and kcalloc to allocate
an array. Probably makes no actual code difference.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the bridge reference count problem and cleanups ipv6 FIB
timer management. Don't use expires field, because it is not a proper
way to test, instead use timer_pending().
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro