This is tested on i.MX27.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This gets rid of one more nfc_is_vX().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This commit makes problems on v1 and v2 regarding 4KiBpages more obvious.
As I don't have a 4KiB flash handy I just keep the status quo.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This gets rid of several instances of cpu_is_mx21() in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
page_read() never returns NULL, so we can remove the NULL check here.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original Broadcom partition order has the root fs in front of the
kernel, which resulted in miscalculated partition sizes.
Detect when such an image is on the flash and also reorder the partitions
accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If a context switch occurs in function omap_wait() just before the
while loop is entered, then upon return from context switch the
timeout may already have elapsed: in that case, status is never
read from NAND device, and omap_wait() returns an error.
This failure has been experimentally observed during stress tests.
This patch ensures a NAND status read is always performed before
returning, as in the generic nand_wait() function.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI
is not enabled, so make it depend on PCI.
drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class
drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If prefetch engine is busy, current code "forgets" to call
dma_unmap_single(), which results in a deadlock later, so add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some not-supported nand chips may pass the current parsing code,
and get the wrong page size and oob size. Sometimes, it's hard to notice
that you get the wrong values, because there is no warning or error.
So it's useful to print out the page size and oob size in the end of
the parsing function. We can check these values with the datasheet of the nand
chip as soon as possible.
Artem: amend the print a bit
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mxs.h does not exit in the mx6q.
So rewrite the __mxs_clrl()/__mxs_setl() and remove the mxs.h.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use cmdlinepart as the default partition parser and allow the arch setup code
to still use their own partition parsers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk+vekgACgkQdwG7hYl686N8bQCfdizsFrliKbDW20R/pO66NoAV
aloAn0ln+mwe3rIdNt8qKynW8e8dbudF
=R7XS
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd
Pull three MTD fixes from David Woodhouse:
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
* tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd:
mtd: ams-delta: fix request_mem_region() failure
jffs2: Fix lock acquisition order bug in gc path
mtd: fix oops in dataflash driver
Using a single definition for the physical and virtual address register for all
variants boards clps711x. This patch also includes the use of a single function
clps_read/write in some units.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all orion platforms can gate the clock, but if it does exist,
enable/disable it as appropriate.
v2: Fix the name of the clkdev entry.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
A call to request_mem_region() has been introduced in the omap-gpio
driver recently (commit 96751fcbe5,
"gpio/omap: Use devm_ API and add request_mem_region"). This change
prevented the Amstrad Delta NAND driver, which was doing the same in
order to take control over OMAP MPU I/O lines that the NAND device hangs
off, from loading successfully.
The I/O lines and corresponding registers used by the NAND driver are a
subset of those used for the GPIO function. Then, to avoid run time
collisions, all MPUIO GPIO lines should be marked as requested while
initializing the NAND driver, and vice versa, a single MPUIO GPIO line
already requested before the NAND driver initialization is attempted
should prevent the NAND device from being started successfully.
There is another driver, omap-keypad, which also manipulates MPUIO
registers, but has never been calling request_mem_region() on startup,
so it's not affected by the change in the gpio-omap and works correctly.
It uses the depreciated omap_read/write functions for accessing MPUIO
registers. Unlike the NAND driver, these I/O lines and registers are
separate from those used by the GPIO driver. However, both register sets
are non-contiguous and overlapping, so it would be impractical to
request the two sets separately, one from the gpio-omap, the other form
the omap-keypad driver.
In order to solve all these issues correctly, a solution first suggested
by Artem Bityutskiy, then closer specified by Tony Lindgren while they
commented the initial version of this fix, should be implemented. The
gpio-omap driver should export a few functions which would allow the
other two drivers to access MPUIO registers in a safe manner instead of
trying to manage them in parallel to the GPIO driver. However, such a
big change, affecting 3 drivers all together, is not suitable for the rc
cycle, and should be prepared for the merge window. Then, an
alternative solution is proposed as a regression fix.
For the ams-delta NAND driver to initialize correctly in coexistence
with the changed GPIO driver, drop the request_mem_region() call from
the former, especially as this call is going to be removed while the
long-term solution is implemented.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I'm seeing an oops in mtd_dataflash.c with Linux 3.3. What appears to
be happening is that otp_select_filemode calls mtd_read_fact_prot_reg
with -1 for offset and length and a NULL buffer to test if OTP
operations are supported. This finds its way down to otp_read in
mtd_dataflash.c and causes an oops when memcpying the returned data
into the NULL buf.
None of the checks in otp_read catches the negative length and offset.
Changing the length of the dummy read to 0 prevents the oops.
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Enable channel in device_issue_pending call, so that the order between
cookie assignment and channel enabling can be ensured naturally.
It fixes the mxs gpmi-nand breakage which is caused by the incorrect
order of cookie assigning and channel enabling.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <b32955@freescale.com>
Tested-by <samgandhi9@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Merge with latest Linus' tree, as I have incoming patches
that fix code that is newer than current HEAD of for-next.
Conflicts:
drivers/net/ethernet/realtek/r8169.c
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull second try at vfs part d#2 from Al Viro:
"Miklos' first series (with do_lookup() rewrite split into edible
chunks) + assorted bits and pieces.
The 'untangling of do_lookup()' series is is a splitup of what used to
be a monolithic patch from Miklos, so this series is basically "how do
I convince myself that his patch is correct (or find a hole in it)".
No holes found and I like the resulting cleanup, so in it went..."
Changes from try 1: Fix a boot problem with selinux, and commit messages
prettied up a bit.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
vfs: fix out-of-date dentry_unhash() comment
vfs: split __lookup_hash
untangling do_lookup() - take __lookup_hash()-calling case out of line.
untangling do_lookup() - switch to calling __lookup_hash()
untangling do_lookup() - merge d_alloc_and_lookup() callers
untangling do_lookup() - merge failure exits in !dentry case
untangling do_lookup() - massage !dentry case towards __lookup_hash()
untangling do_lookup() - get rid of need_reval in !dentry case
untangling do_lookup() - eliminate a loop.
untangling do_lookup() - expand the area under ->i_mutex
untangling do_lookup() - isolate !dentry stuff from the rest of it.
vfs: move MAY_EXEC check from __lookup_hash()
vfs: don't revalidate just looked up dentry
vfs: fix d_need_lookup/d_revalidate order in do_lookup
ext3: move headers to fs/ext3/
migrate ext2_fs.h guts to fs/ext2/ext2.h
new helper: ext2_image_size()
get rid of pointless includes of ext2_fs.h
ext2: No longer export ext2_fs.h to user space
mtdchar: kill persistently held vfsmount
...
... and mtdchar_notifier along with it; just have ->drop_inode() that
will unconditionally get evict them instead of dances on mtd device
removal and use simple_pin_fs() instead of kern_mount()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a number of
on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wiKV
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More device tree support updates" from Olof Johansson:
"This branch contains a number of updates for device tree support on
several ARM platforms, in particular:
* AT91 continues the device tree conversion adding support for a
number of on-chip drivers and other functionality
* ux500 adds probing of some of the core SoC blocks through device
tree
* Initial device tree support for ST SPEAr600 platforms
* kirkwood continues the conversion to device-tree probing"
Manually merge arch/arm/mach-ux500/Kconfig due to MACH_U8500 rename, and
drivers/usb/gadget/at91_udc.c due to header file include cleanups.
Also do an "evil merge" for the MACH_U8500 config option rename that the
affected RMI4 touchscreen driver in staging. It's called MACH_MOP500
now, and it was missed during previous merges.
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: SPEAr600: Add device-tree support to SPEAr600 boards
ARM: ux500: Provide local timer support for Device Tree
ARM: ux500: Enable PL022 SSP Controller in Device Tree
ARM: ux500: Enable PL310 Level 2 Cache Controller in Device Tree
ARM: ux500: Enable PL011 AMBA UART Controller for Device Tree
ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device Tree
ARM: ux500: db8500: list most devices in the snowball device tree
ARM: ux500: split dts file for snowball into generic part
ARM: ux500: combine the board init functions for DT boot
ARM: ux500: Initial Device Tree support for Snowball
ARM: ux500: CONFIG: Enable Device Tree support for future endeavours
ARM: kirkwood: use devicetree for rtc-mv
ARM: kirkwood: rtc-mv devicetree bindings
ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
ARM: kirkwood: fdt: facilitate new boards during fdt migration
ARM: kirkwood: fdt: absorb kirkwood_init()
ARM: kirkwood: fdt: use mrvl ticker symbol
ARM: orion: wdt: use resource vice direct access
ARM: Kirkwood: Remove tclk from kirkwood_asoc_platform_data.
ARM: orion: spi: remove enable_clock_fix which is not used
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Pull UML changes from Richard Weinberger:
"Mostly bug fixes and cleanups"
* 'for-linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: (35 commits)
um: Update defconfig
um: Switch to large mcmodel on x86_64
MTD: Relax dependencies
um: Wire CONFIG_GENERIC_IO up
um: Serve io_remap_pfn_range()
Introduce CONFIG_GENERIC_IO
um: allow SUBARCH=x86
um: most of the SUBARCH uses can be killed
um: deadlock in line_write_interrupt()
um: don't bother trying to rebuild CHECKFLAGS for USER_OBJS
um: use the right ifdef around exports in user_syms.c
um: a bunch of headers can be killed by using generic-y
um: ptrace-generic.h doesn't need user.h
um: kill HOST_TASK_PID
um: remove pointless include of asm/fixmap.h from asm/pgtable.h
um: asm-offsets.h might as well come from underlying arch...
um: merge processor_{32,64}.h a bit...
um: switch close_chan() to struct line
um: race fix: initialize delayed_work *before* registering IRQ
um: line->have_irq is never checked...
...
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
These changes are all specific to one board only. We're trying to keep
the number of board files low, but generally board level updates are
ok on platforms that are working on moving towards DT based probing,
which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal of
ams_delta_config and the addition of a lot of other data. The Kconfig
file has two changes in the same line, and in exynos, the power domain
cleanup conflicts with the addition of the image sensor device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HPiJ
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
"These changes are all specific to one board only. We're trying to
keep the number of board files low, but generally board level updates
are ok on platforms that are working on moving towards DT based
probing, which will eventually lead to removing them.
The board-ams-delta.c board file gets a conflict between the removal
of ams_delta_config and the addition of a lot of other data. The
Kconfig file has two changes in the same line, and in exynos, the
power domain cleanup conflicts with the addition of the image sensor
device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: Amended a fix for a mismerge to board-omap4panda.c]
Signed-off-by: Olof Johansson <olof@lixom.net>"
Fixed up some fairly trivial conflicts manually.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
i.MX35-PDK: Add Camera support
ARM : mx35: 3ds-board: add framebuffer device
pxa/hx4700: Remove pcmcia platform_device structure
ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
ARM: pxa/hx4700: Remove unwanted request for GPIO105
ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
ARM: EXYNOS: Register JPEG on nuri
ARM: EXYNOS: Register JPEG on universal_c210
ARM: S5PV210: Enable JPEG on SMDKV210
ARM: S5PV210: Add JPEG board definition
ARM: EXYNOS: Enable JPEG on Origen
ARM: EXYNOS: Enable JPEG on SMDKV310
ARM: EXYNOS: Add __init attribute to universal_camera_init()
ARM: EXYNOS: Add __init attribute to nuri_camera_init()
ARM: S5PV210: Enable FIMC on SMDKC110
ARM: S5PV210: Enable FIMC on SMDKV210
ARM: S5PV210: Enable MFC on SMDKC110
ARM: S5PV210: Enable MFC on SMDKV210
ARM: EXYNOS: Enable G2D on SMDKV310
ARM: tegra: update defconfig
...
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
As docg3 is intolerant against reentrancy, especially
because of its weird register access (ie. a register read is
performed by a first register write), each access to the
docg3 IO space must be locked.
Lock the IO space with a mutex, shared by all chips on the
same cascade, as they all share the same IO space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Group floors into a common cascade structure. This will provide a common
structure to store common data to all cascaded docg3 chips, like IO
addressing, locking protection.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After several tries with ubifs, it appears empirically that constructor
provided figures for erase/write timeouts are underestimated. A timeout
of 100ms seems to work with a 5 years worn chip, and no timeouts occur
anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The last erase block was not accessible, as the out of bound
check was incorrectly rejecting the last block.
The read/write/erase offset checks were forbidding the usage of the
last block, because of the calculation which was considering the
byte after the last instead of the last byte.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A lot of functions have been marked __devinit, but they shouldn't, because they
are needed for bbt_scan. While I believe the whole MX23 handling should be done
entirely different, I am missing the resources to fix it. So, let's have at least
the annotations correct.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
phram_setup() is only called from init_phram() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Initialization of 'erase_info->fail_addr' to MTD_FAIL_ADDR_UNKNOWN prior
erase operation is duplicated accross several MTD drivers, and also taken
care of by some MTD users as well.
Harmonize it: initialize 'fail_addr' within 'mtd_erase()' interface.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With onfi a flash is organized into one or more logical units (LUNs).
A logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Additionally, after failing in mtd_device_parse_register(), the driver
unmap/free code is now executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the FSMC NAND driver (used amongst
others on SPEAr platforms) via device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
doc_probe_device() is only called from docg3_probe() which is in .init.text,
so it must be in the same section to avoid a section mismatch warning.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The fsmc_nand driver uses cpu to read/write onto the device. This is inefficient
because of two reasons
- the cpu gets locked on AHB bus while reading from NAND
- the cpu is unnecessarily used when dma can do the job
This patch adds the support for accessing the device through DMA
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The default way of accessing nand device is using the nand width. This means
that 8bit devices are using u8 * and 16bit devices are accessed using u16 *.
This results in a non-optimal performance since the FSMC is designed to
translate the normal word accesses into device width based accesses. This patch
implements read_buf and write_buf callbacks using word by word accesses.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
fsmc controller takes time to calculate the bch8 codes and the error offsets.
The calculate logic checks for completion upto a timeout. This patch adds a
error print when this timer expires and the ecc or error offsets are not yet
calculated.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
fsmc_nand driver currently uses normal kzalloc, request_mem etc routines. This
patch replaces these routines with devm_kzalloc and devm_request_mem_region etc.
Consequently, the error and driver removal scenarios are curtailed.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
FSMC controllers provide registers to program the required timing values for
attached NAND device. The timing values used until now are relaxed and should
work for all devices.
Although, for read/write performance improvements, the fsmc nand driver should
accept nand timings as a platform data and program the timing parameters into
fsmc registers accordingly.
This patch implements this modification. Additionally, it programs the default
timing parameters if these are not passed via platform data.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ideally, the block should have 0xff written on the bad block position. Any value
other than 0xff implies a bad block. In practical situations, there can be
bit flips in the oob area as well which means that a block with 0x7f being read
at bad block position may imply a bad block but it is infact only a bit flip in
the bad block byte.
To resolve this problem, the block is marked as good if number of high bits is
greater than or equal to badblockbits (initialized to 7)
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ECC can correct up to 8 bits in 512 bytes data + 13 bytes ecc. This means that
the algorithm can correct a max of 8 bits in 4200 bits ie the error indices can
be from 0 to 4199. Of these 0 to 4095 are for data and 4096 to 4199 for ecc.
The driver flips the bit only if the index is <= 4096. This is a bug since the
data bits are only from 0 to 4095.
This patch modifies the check as < 4096
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ECC logic of FSMC works on 512 bytes data + 13 bytes ECC to generate error
indices of up to 8 incorrect bits. The FSMC driver reads 14 instead of 13 oob
bytes to accommodate for 16 bit device as well.
Unfortunately, the internal ecc state machine gets corrupted for 8 bit devices
reading 512 + 14 bytes of data resulting in error indices not getting reported.
Fix this by reading 14 bytes only for 16 bit devices
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch reimplements the passing of partition information through platform
data. This was unintentionally deleted in commit
0d04eda143
"mtd: fsmc_nand.c: use mtd_device_parse_register"
Artem: fix gcc warning about passin 0 instead of NULL.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is based on Ville Herva's similar patch to block2mtd.
Trying to pass a parameter through the kernel command line when built-in would
crash the kernel, as phram_setup() was called so early that kmalloc() was not
functional yet.
This patch only saves the parameter string at the early boot stage, and parses
it later when init_phram() is called. The same happens in both module and
built-in cases.
With this patch, I can boot with a statically-compiled phram, and mount a
ext2 root fs from physical RAM, without the need for a initrd.
This has been tested in built-in and module cases, with and without a
parameter string.
Artem: amended comments a bit
Signed-off-by: Hervé Fache <h-fache@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The last DMA command of ECC read page is used to disable the BCH module.
But the original code missed to set the pio[2] which is used to set the
GPMI_HW_GPMI_ECCCTRL register. fix it now.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Flash device drivers initialize 'ecc_strength' in struct mtd_info, which is the
maximum number of bit errors that can be corrected in one writesize region.
Drivers using the nand interface intitialize 'strength' in struct nand_ecc_ctrl,
which is the maximum number of bit errors that can be corrected in one ecc step.
Nand infrastructure code translates this to 'ecc_strength'.
Also for nand drivers, the nand infrastructure code sets ecc.strength for ecc
modes NAND_ECC_SOFT, NAND_ECC_SOFT_BCH, and NAND_ECC_NONE. It is set in the
driver for all other modes.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The read function was so far requiring the reads to be aligned on page
boundaries, and be page length multiples in size. Relieve these
constraints to ease the userspace ubifs programs runs, which read ubifs
headers of 64 bytes.
Artem: squashed a later fix from Robert Jarzmik into this patch.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds power management code with fine granularity. Every flash control
command is enclosed by runtime_put()/get()s. To make sure that no
overhead is generated by too frequent power state switches, a quality of
service request is issued.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first 3 arguments of 'mtd_device_parse_register()' are pointers,
but many callers pass '0' instead of 'NULL'. Fix this globally. Thanks
to coccinelle for making it easy to do with the following semantic patch:
@@
expression mtd, types, parser_data, parts, nr_parts;
@@
(
-mtd_device_parse_register(mtd, 0, parser_data, parts, nr_parts)
+mtd_device_parse_register(mtd, NULL, parser_data, parts, nr_parts)
|
-mtd_device_parse_register(mtd, types, 0, parts, nr_parts)
+mtd_device_parse_register(mtd, types, NULL, parts, nr_parts)
|
-mtd_device_parse_register(mtd, types, parser_data, 0, nr_parts)
+mtd_device_parse_register(mtd, types, parser_data, NULL, nr_parts)
)
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a set which fixes unnecessary flash erase and write errors
resulting from the MTD CFI driver turning off vpp while an erase is in progress.
This patch allows sa1100_set_vpp() calls to be nested by adding a reference
counter.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a set which fixes unnecessary flash erase and write errors
resulting from the MTD CFI driver turning off vpp while an erase is in progress.
This patch allows pcmciamtd_set_vpp() calls to be nested by adding a reference
counter.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a set which fixes unnecessary flash erase and write errors
resulting from the MTD CFI driver turning off vpp while an erase is in progress.
This patch allows l440gx_set_vpp() calls to be nested by adding a reference
counter.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a set which fixes unnecessary flash erase and write errors
resulting from the MTD CFI driver turning off vpp while an erase is in progress.
This patch allows physmap_set_vpp() calls to be nested by adding a reference
counter.
omap1_set_vpp() already used a reference counter. Since it is called from
physmap_set_vpp(), omap1_set_vpp() can now be simplified.
simtec_nor_vpp() already disabled hard interrupts. Since it is called from
physmap_set_vpp(), simtec_nor_vpp() can now be simplified.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a set which fixes unnecessary flash erase and write errors
resulting from the MTD CFI driver turning off vpp while an erase is in progress.
This patch ensures that only those flash operations which call ENABLE_VPP() can
then call DISABLE_VPP(). Other operations should never call DISABLE_VPP().
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a set which fixes unnecessary flash erase and write errors
resulting from the MTD CFI driver turning off vpp while an erase is in progress.
This patch ensures that only those flash operations which call ENABLE_VPP() can
then call DISABLE_VPP(). Other operations should never call DISABLE_VPP().
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current patch is required to support EVALSPEAR1340CPU
Revision 2 where a new (ONFI compliant) MT29F16G08 NAND
flash from Micron is present.
This NAND flash device defines a OOB area which is
224 bytes long (oobsize).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch improves the error correction routine for bch8
- Loop only up to number of errors detected
- Improve the error index calculation procedure
Additionally, it also renames the "correct" routine to indicate that it is bch8
specific
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since change_bit() requires a (unsigned int *) as second arg,
the correct definition of err_idx[] array declared as
local variable of fsmc_correct_data() is the following:
u32 err_idx[8];
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ALE and CLE offsets can be different on different devices. Let devices
pass these offsets to the fsmc driver through platform data.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ECC1 & ECC4 layout for NAND of different pages sizes for e.g. 512bytes,
2KiB, 4KiB and 8KiB are separated. Previously there existed one ECC4
layout for 2KiB & 4KiB page size due to which oob test module available
in drivers/mtd/nand/test was failing.
Signed-off-by: Bhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A newly erased page contains ff in data as well as spare area. While reading an
erased page, the read out ecc from spare area does not match the ecc generated
by fsmc ecc hardware accelerator. This is because ecc of data ff ff is not ff
ff. This leads to errors when file system erases and reads back the pages to
ensure consistency.
This patch adds a software workaround to ensure that the ecc check is not
performed for erased pages. This problem is solved by checking the number of
bits (in 512 byte data + 13 byte ecc) which are 0. If these number of bits are
less than 8, the page is considered erased and correction algorithm is not tried
on that page
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch reverts a change that may have been mistakenly included with the set
of patches that introduced the new mtd api entry functions. Or perhaps I am
mistaken :)
The problem is in the partition wrapper functions, where the calls to the driver
methods were replaced with calls to the new mtd api functions. This causes the
api function to be called a second time, further down the call stack. This is
not only unnecessary and redundant - because the sanity checking code and (more
restrictive) bounds checks for the partition were done in the first call - but
is potentially problematic and confusing.
For example, the call stack for a call to mtd_read() on a partitioned device
currently looks like this:
mtd_read() gets struct mtd_info for the partition
|
+-> part_read() via the pointer assigned when the partition was created
|
+->mtd_read() this time gets struct mtd_info for the master
|
+->xyz_driver_read() via the pointer asigned by the driver
It seems that this can cause a variety of problems. For example, if you want to
add code to the api function that tests a value in mtd_info that is relevant
only to the partition. Or (in my case) you want the driver to return a value
that may be different from that returned by the mtd api function.
This patch eliminates the second call to the mtd api function. It was tested on
the docg4 nand driver with a subset of the api functions, but I inspected the
rest and don't see any problems.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the name of the mtd so that it is simpler, and is easier to
cope with by mtdparts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a register used in new FLCTL hardware and a feature flag for it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of reading out the register, use a cached value. This will
make way for a proper runtime power management implementation.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Implements the command to seek and read in pages.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The nand base code wants to read out 8 bytes in the READID command.
Reflect this in the driver code.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reorders the calls to make it a bit shorter and match the calling
procedure displayed in the datasheet.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since commit ca97dec2ab the
command line parsing of MTD partitions does not work anymore.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some strange nand chip(such as Hynix H27UBG8T2A) can pass the `ONFI` signature
check. So the log can be printed out even it is not an ONFI nand indeed.
Change this log to the end of the function. Print out the log only when we
really detect an ONFI nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[1] Background :
The GPMI does ECC read page operation with a DMA chain consist of three DMA
Command Structures. The middle one of the chain is used to enable the BCH,
and read out the NAND page.
The WAIT4END(wait for command end) is a comunication signal between
the GPMI and MXS-DMA.
[2] The current DMA code sets the WAIT4END bit at the last one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^
|
|
set WAIT4END here
This chain works fine in the mx23/mx28.
[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
be set not only at the last DMA Command Structure,
but also at the middle one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^ ^
| |
| |
set WAIT4END here too set WAIT4END here
If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state.
In the next ECC write page operation, a DMA-timeout occurs.
This has been catched in the MX6Q board.
[4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(),
and use the dma_ctrl_flags:
---------------------------------------------------------
DMA_PREP_INTERRUPT : append a new DMA Command Structrue.
DMA_CTRL_ACK : set the WAIT4END bit for this DMA Command Structure.
---------------------------------------------------------
[5] changes to the relative drivers:
<1> For mxs-mmc driver, just use the new flags, do not change any logic.
<2> For gpmi-nand driver, and use the new flags to set the DMA
chain, especially for ecc read page.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q. It will also be used in the future chips.
Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.
change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
While debugging on SA11x0, the following message was observed:
"Flash device refused suspend due to active operation (state 20)"
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The gpmi driver selects the MTD_CMDLINE_PARTS directly.
But we should not select a visible symbol.
Just remove the select.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit "c797533 mtd: abstract last MTD partition parser argument" the
third argument of "mtd_device_parse_register()" changed from start address
of the MTD device to a pointer to a struct.
The "ixp4xx_flash_probe()" function was not converted properly, causing
an oops during boot.
This patch fixes the problem by filling the needed information into a
"struct mtd_part_parser_data" and passing it to
"mtd_device_parse_register()".
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.
This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some MTD drivers return -EINVAL if the 'phys' parameter is not NULL, trying to
convey that they cannot return the physical address. However, this is not very
logical because they still can return the virtual address ('virt'). But some
drivers (lpddr) just ignore the 'phys' parameter instead, which is a more
logical thing to do.
Let's harmonize this and:
1. Always initialize 'virt' and 'phys' to 'NULL' in 'mtd_point()'.
2. Do not return an error if the physical address cannot be found.
So as a result, all drivers will set 'phys' to 'NULL' if it is not supported.
None of the 'mtd_point()' users use 'phys' anyway, so this should not break
anything. I guess we could also just delete this parameter later.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:
'mtd_point()'
'mtd_read()'
'mtd_write()'
'mtd_writev()'
'mtd_panic_write()'
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add verification of the offset and length to MTD API functions and verify that
MTD device offset and length are within MTD device size.
The modified API functions are:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch also uninlines these functions and exports in mtdcore.c because they
are not performance-critical and do not have to be inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* bootloader cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not need to invoke 'mtd_can_have_bb()' before invoking
'mtd_block_isbad()' because the latter already handles the case when the MTD
device does not support bad blocks.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The main 'mtd_block_markbad()' function returns -EOPNOTSUPP if the
'->block_markbad' method is undefined, and mtdconcat should do the same.
Fix this by simply removing the 'mtd_can_have_bb()' because it is not
really necessary. It could be treated as an optimization, but this function is
expected to be used so rarely that it does not matter.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to 4 because this drivers writes at max 4 bytes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE
because this is actually the amount of data we write at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Joern Engel <joern@lazybastard.org>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Gcc complains here:
drivers/mtd/nand/docg4.c: In function ‘probe_docg4’:
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘resource_size_t’ [-Wformat]
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘resource_size_t’ [-Wformat]
We have a standard way of printing these using a format string
extension.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This has been moved from .options to .bbt_options meanwhile. So, it
currently checks for something totally different (NAND_OWN_BUFFERS) and
decides according to that.
Artem Bityutskiy: the options were moved in
a40f734 mtd: nand: consolidate redundant flash-based BBT flags
Artem Bityutskiy: CCing -stable
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using UBI on m25p80 can give messages like:
UBI error: io_init: bad write buffer size 0 for 1 min. I/O unit
We need to initialize writebufsize; I think "page_size" is the correct
"bufsize", although I'm not sure. Comments?
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We don't need to to check for mtd->resume before calling mtd_resume().
mtd_resume() should take care of that.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a driver for the M-Sys / Sandisk diskonchip G4 nand flash found
in various smartphones and PDAs, among them the Palm Treo680, HTC Prophet and
Wizard, Toshiba Portege G900, Asus P526, and O2 XDA Zinc. It was tested on the
Treo 680, but should work generically.
Since v3, this patch adds power management functions, a scan of the factory bad
block table during initialization, several fixes, and more extensive testing.
Also, the platform data header file, which only contained partitioning
information, was removed. Command-line partitioning can be used, at least until
an mtd parser is written for the saftl format with which these chips are
shipped.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the drivers in drivers/mtd/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As nand_default_block_markbad() is becoming more complex, it helps to
have code appear only in its relevant codepath(s). Here, the calculation
of `ofs' based on NAND_BBT_SCANLASTPAGE is only useful on paths where we
write bad block markers to OOB. We move the condition/calculation closer
to the `write' operation and update the comment to more correctly
describe the operation.
The variable `wr_ofs' is also used to help isolate our calculation of
the "write" offset from the usage of `ofs' to represent the eraseblock
offset. This will become useful when we reorder operations in the next
patch.
This patch should make no functional change.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtdoops usage instructions found in Kconfig have been incorrect
since:
commit 2e386e4bac
mtd: mtdoops: refactor as a kmsg_dumper
mtdoops no longer uses a console. Now, if you build it into your kernel,
you add something like the following to your command line to select
partition X as your logging partition:
mtdoops.mtddev=X
Anyway, it seems better to leave the documentation out of Kconfig.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
/*
* This is here for documentation purposes only - until these people
* submit their machine types. It will be gone January 2005.
*/
It's now seven years after that date, so let's remove this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit c4a9f88daf ([MTD] [NOR] fix ctrl-alt-del can't reboot for
intel flash bug) interferes with this work-around, causing MTD to
issue this warning:
Flash device refused suspend due to active operation (state 0)
The commit makes our work-around in the map driver unnecessary, so
let's remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Driver must cleanup all held resources during remove. It wasn't
releasing requested memory region.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It seems that we have developed a bad-block-marking "feature" out of
pure laziness:
"We write two bytes per location, so we dont have to mess with 16 bit
access."
It's relatively simple to write a 1 byte at a time on x8 devices and 2
bytes at a time on x16 devices, so let's do it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_block_bad() doesn't check the correct pages when
NAND_BBT_SCAN2NDPAGE is enabled. It should scan both the OOB region of
both the 1st and 2nd page of each block.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many NAND flash systems (especially those with MLC NAND) cannot be
reliably written twice in a row. For instance, when marking a bad block,
the block may already have data written to it, and so we should attempt
to erase the block before writing a bad block marker to its OOB region.
We can ignore erase failures, since the block may be bad such that it
cannot be erased properly; we still attempt to write zeros to its spare
area.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the following build warning:
drivers/mtd/mtdcore.c: In function ‘mtd_release’:
drivers/mtd/mtdcore.c:110: warning: unused variable ‘mtd’
This happens when neither CONFIG_MTD_CHAR nor CONFIG_MTD_CHAR_MODULE are defined.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.
Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since "length" is a u32, the error handling below didn't work when
fixup_pmc551() returns -ENODEV.
if ((length = fixup_pmc551(PCI_Device)) <= 0)
This patch changes both the type of "length" and the return type of
fixup_pmc551() to int.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Uwe Kleine-König