By the way add few chipsets that were tracked with "wl" dumps.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to properly handle early 802.11n devices like BCM4321.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spinlock protecting the L2CAP ident number can be converted into
a mutex since the whole processing is run in a workqueue. So instead
of using a spinlock, just use a mutex here.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for LE encryption is optional. When encryption is not
supported then also do not enable the encryption related events.
This moves the event mask setting to the third initialization
stage to ensure that the LE features are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no external user of the SCO timeout constants and thus
move them into net/bluetooth/sco.c where they are actuallu used.
In addition just remove SCO_CONN_IDLE_TIMEOUT since it is unused.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SCO_DEFAULT_FLUSH_TO constant has been defined, but it is not
used anywhere and so just remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There exists no external user of struct sco_conn and thus move
it into the one place that is actually using it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There exists no external user of struct sco_pinfo and sco_pi and
thus move it into the one place that is actually using it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The list of L2CAP fixed channels increased with newer versions of the
specification. This just updates the constants for it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The internals of the HCI request framework should not be leaking to
its users. Move them all into net/bluetooth/hci_core.c and provide
a simple hci_req_pending helper function for the one user outside
the framework.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There exists no external user of struct hci_pinfo and hci_pi and thus
move it into the one place that is actually using it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is only single location using struct hci_sec_filter and with
that there is no point in putting this declaration into a global
header file. So move it right next to its user and make the code
a lot more simpler.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All the HCI sockets and ioctl based definitions have been in a global
header file that also includes all the HCI protocol structures. To
make this a bit cleaner, move them into its own file.
This also adjusts fs/compat_ioctl.c to only include this new file
and not all the protocol structures that are not needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set Connectable/Discoverable mgmt handlers use a hci_request with a
proper callback to handle the HCI command sending. It makes therefore
little sense to have this extra function to be called from hci_event.c
for command failures.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCISETSCAN ioctl is the only non-mgmt user we care about for
setting the right discoverable state we can simply do the necessary
updates in the ioctl handler function instead. This then allows the
removal of the mgmt_discoverable function and should simplify that state
handling considerably.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt_connectable function has been used to ensure that the right
actions to HCI_CONNECTABLE are taken when the HCI_Write_Scan_Enable
command is triggered by something else than mgmt. The only other user
that we really care about is the HCISETSCAN ioctl code, so we can
actually more simply perform the needed changes there instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the real advertising state is now tracked with its own flag we can
simply set/unset the HCI_ADVERTISING flag in the
set_advertising_complete function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Having a single HCI_ADVERTISING flag is problematic since it tries to
track both the real advertising state and the corresponding mgmt
setting. To make the logic simpler and more reliable add a new flag that
only tracks the actual advertising state that has been written to the
controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be
initialized differently.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we have both LE scanning and advertising simultaneously enabled we
need a way to tell hci_connect_le() in which role to initiate a
connection. This patch adds a new parameter to the function to give it
the necessary information. For auto-connect and mgmt_pair_device we
always use master role, whereas for L2CAP users (in practice sockets) we
use slave role whenever HCI_ADVERTISING is set and master role
otherwise.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The auth_type value which gets assigned to hci_conn->auth_type is
something that's only used for BR/EDR connections and is of no value for
LE connections. It makes therefore little sense to pass it to the
hci_connect_le() function. This patch removes the parameter from the
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we establish connections as a consequence of receiving an
advertising report it makes no sense to wait the normal 20 second LE
connection timeout. This patch modifies the hci_connect_le function to
take an extra timeout value and uses a lower 2 second timeout for the
auto-connection case. This timeout is intentionally chosen to be just a
bit higher than the 1.28 second timeout that High Duty Cycle Advertising
uses.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for changing the public device address. This feature
is required by controllers that do not provide a public address and
have HCI_QUIRK_INVALID_BDADDR set.
Even if a controller has a public device address, this is useful when
an embedded system wants to use its own value. As long as the driver
provides the set_bdaddr callback, this allows changing the device
address before powering on the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the external configuration triggers the switch to a configured
controller, it means the setup needs to be run. Controllers that start
out unconfigured have only run limited set of HCI commands. This is
not enough for complete operation and thus run the setup procedure
before announcing the new controller index.
This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The
HCI_SETUP flag is only used once for the initial setup procedure. And
during that procedure hdev->setup driver callback is called. With the
new HCI_CONFIG the switch from unconfigured to configured state is
triggering the same setup procedure just without hdev->setup. This
is required since bringing a controller back to unconfigured state
from configured state is possible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling Device Remove with BDADDR_ANY we should in a similar way
emit Device Removed events as we do when removing a single device. Since
we have to iterate the list and call device_removed() the dedicated
hci_conn_params_clear_enabled() is not really useful anymore. This patch
removes the helper function and does the event emission and list item
removal in a single loop.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During the setup phase of a controller, the Bluetooth address will be
read and to have that original address available for later use, store
it as setup address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When one or more of the missing configuration options change, then send
this even to all the other management interface clients.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Set External Configuration management command allows for switching
between configured and unconfigured start if HCI_QURIK_EXTERNAL_CONFIG
is set by the transport driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The current existing device quirks are not documented. So instead of
spreading bits and pieces somewhere in the code, add proper comments
on where these quirks can be used and what behavior they change.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The public address configuration option is value 0x02 since the generic
external configuration is value 0x01. So adjust this accordingly and
also add the value 0x01 to the list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to make the right choice of whether to start passive scanning
or to send out a mgmt_device_found event we need to know if there are
any devices in the le_conn_params list with the auto_connect value set
to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command allows to get the list of currently known controller that
are in unconfigured state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller in an unconfigured state gets removed, then send
Unconfigured Index Removed events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Rafał Miłecki