During heavy tx traffic, control messages (sent by liquidio driver to NIC
firmware) sometimes do not get processed in a timely manner. Reason is:
the low-level metadata of control messages and that of egress network
packets indicate that they have the same priority.
Fix it by setting a higher priority for control messages through the new
ctrl_qpg field in the oct_txpciq struct. It is the NIC firmware that does
the actual setting of priority by writing to the new ctrl_qpg field; the
host driver treats that value as opaque and just assigns it to pki_ih3->qpg
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink support to netdevsim and use it to implement a simple,
profile based resource controller. Only one controller is needed
per namespace, so the first netdevsim netdevice in a namespace
registers with devlink. If that device is deleted, the resource
settings are deleted.
The resource controller allows a user to limit the number of IPv4 and
IPv6 FIB entries and FIB rules. The resource paths are:
/IPv4
/IPv4/fib
/IPv4/fib-rules
/IPv6
/IPv6/fib
/IPv6/fib-rules
The IPv4 and IPv6 top level resources are unlimited in size and can not
be changed. From there, the number of FIB entries and FIB rule entries
are unlimited by default. A user can specify a limit for the fib and
fib-rules resources:
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 96
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib-rules size 16
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib size 64
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib-rules size 16
$ devlink dev reload netdevsim/netdevsim0
such that the number of rules or routes is limited (96 ipv4 routes in the
example above):
$ for n in $(seq 1 32); do ip ro add 10.99.$n.0/24 dev eth1; done
Error: netdevsim: Exceeded number of supported fib entries.
$ devlink resource show netdevsim/netdevsim0
netdevsim/netdevsim0:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables non
resources:
name fib size 96 occ 96 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables
...
With this template in place for resource management, it is fairly trivial
to extend and shows one way to implement a simple counter based resource
controller typical of network profiles.
Currently, devlink only supports initial namespace. Code is in place to
adapt netdevsim to a per namespace controller once the network namespace
issues are resolved.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauuK/AAoJEEg/ir3gV/o+Ro4IAIBcQl4S/6jPttGDOPwElU4b
Q8MuQbnB9k36Kf6x3GrhBqwtoS3OYBLvfyOeZsghD8uyzklhnqR/psrCt1YhLXq7
aI5iFbuQucCUwIYBscuZegXBs+PTJYALoil05hOwSkwhEBZR53ZvdRQ9Jg0G0QiY
sYEYAl41A1DWQOLET5lwleUpVQnVnNvIcXqNHKBKbS4f8rmLpfsZ6YAxJiiIjeDJ
gLbsaxUyY3p77594okBk6DuFBWZsEAKwumspdSc92OEMrZSYE5ugNL+UgVEE7I8F
JgK/4OUarw3K7xwhAg//ZhTM1iRRdJv0Sz2GPhhWRzYB0jWACc3ZG2/M/WmxFIg=
=Uslu
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-27 (Misc updates & SQ recovery)
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can have interrupts left enabled form e.g: the bootloader which used
the network device for network boot. Make sure we have those disabled as
early as possible to avoid spurious interrupts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system contains several BGMAC adapters, it is nice to be able
to tell which one is which by looking at /proc/interrupts. Use the
network device name as a name to request_irq() with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the National Instruments XGE 1/10G network device.
It uses the EEPROM on the board via NVMEM.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent change to netvsc drive in how receive flags are handled
broke multicast. The Hyper-v/Azure virtual interface there is not a
multicast filter list, filtering is only all or none. The driver must
enable all multicast if any multicast address is present.
Fixes: 009f766ca2 ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.
Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.
Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ca8210_test_int_user_write() a user can request the transfer of a
frame with a length field (command.length) that is longer than the
actual buffer provided (len). In this scenario the driver will copy
the buffer contents into the uninitialised command[] buffer, then
transfer <data.length> bytes over the SPI even though only <len> bytes
had been populated, potentially leaking sensitive kernel memory.
Also the first 6 bytes of the command buffer must be initialised in case
a malformed, short packet is written and the uninitialised bytes are
read in ca8210_test_check_upstream.
Reported-by: Domen Puncer Kugler <domen.puncer@samsung.com>
Signed-off-by: Harry Morris <h.morris@cascoda.com>
Tested-by: Harry Morris <h.morris@cascoda.com>
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
ath.git patches for 4.17. Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
Remove the static array and use the generic routine to set the
Ethernet broadcast address.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().
This will fix below warning,
WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
invalid rate bw=1, mcs=9, nss=2
(unwind_backtrace) from
(cfg80211_calculate_bitrate+0x174/0x220)
(cfg80211_calculate_bitrate) from
(nl80211_put_sta_rate+0x44/0x1dc)from
(nl80211_put_sta_rate) from
(nl80211_send_station+0x388/0xaf0)
(nl80211_get_station+0xa8/0xec)
[ end trace da8257d6a850e91a ]
Fixes: 842be75c77 ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes regression caused by 0c317a02ca
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.
Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053
Fixes: 0c317a02ca ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: Yingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.
Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.
Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.
Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.
Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware of QCA6174/QCA9377 already support the feature, just enable
it to be able to handle the get_temperature command and process the event.
You can read the temperature by using the hwmon interface,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Verified with the following hardware and software combination,
QCA6174, only firmware-4.bin doesn't support this, otherwise all support.
QCA9377, all the firmwares upstreamed support this command
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
some userspace programs (e.g. hostapd) need to set the regulatory domain
before selecting the operating channel. Synchronize DFS detector regardless of
the value of ah->curchan, to avoid situations where wireless scan can't be done
on some 5GHz sub-bands, because dfs_region is constantly UNSET.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Timothy Redaelli <tredaelli@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When FW responds with a message of wrong size or type make sure
the type is checked first and included in the wrong size message.
This makes it easier to figure out which FW command failed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
NFP has a prng register, which we can read to obtain a u32 worth
of pseudo random data. Generate code for it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow atomic add to be used even when the value is not guaranteed
to fit into a 16 bit immediate. This requires the value to be pulled
as data, and therefore use of a transfer register and a context swap.
Track the information about possible lengths of the value, if it's
guaranteed to be larger than 16bits don't generate the code for the
optimized case at all.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Allow callers to control the delay slots of commands, instead of
giving them just a wait/nowait choice.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement atomic add operation for 32 and 64 bit values. Depend
on the verifier to ensure alignment. Values have to be kept in
big endian and swapped upon read/write. For now only support
atomic add of a constant.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Support calling map_delete_elem() FW helper from the datapath
programs. For JIT checks and code are basically equivalent
to map lookups. Similarly to other map helper key must be on
the stack. Different pointer types are left for future extension.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Support calling map_update_elem() from the datapath programs
by calling into FW-provided helper. Value pointer is passed
in LM pointer #2. Keeping track of old state for arg3 is not
necessary, since LM pointer #2 will be always loaded in this
case, the trivial optimization for value at the bottom of the
stack can't be done here.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a verifier helper for performing the basic state checks
before a call to a map helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Our implementation has restriction on stack pointers for function
calls. Move the common checks into a helper for reuse. The state
has to be encapsulated into a structure to support parameters
other than BPF_REG_2.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
We will reuse most of map call code gen for other map calls.
Rename the lookup gen function and use meta->func_id instead
of hard-coding lookup.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch is the front end of this optimisation, it detects and marks
those packet reads that could be cached. Then the optimisation "backend"
will be activated automatically.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch add the support for unaligned read offset, i.e. the read offset
to the start of packet cache area is not aligned to REG_WIDTH. In this
case, the read area might across maximum three transfer-in registers.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch assumes there is a packet data cache, and would try to read
packet data from the cache instead of from memory.
This patch only implements the optimisation "backend", it doesn't build
the packet data cache, so this optimisation is not enabled.
This patch has only enabled aligned packet data read, i.e. when the read
offset to the start of cache is REG_WIDTH aligned.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
fix iwlwifi_dev_ucode_error tracepoint to pass pointer to a table
instead of all 17 arguments by value.
dvm/main.c and mvm/utils.c have 'struct iwl_error_event_table'
defined with very similar yet subtly different fields and offsets.
tracepoint is still common and using definition of 'struct iwl_error_event_table'
from dvm/commands.h while copying fields.
Long term this tracepoint probably should be split into two.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
two trace events defined with the same name and both unused.
They conflict in allyesconfig build. Rename one of them.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We can set triggers that cause a debug data collection when something
of interest happens (e.g. when too many probes are lost conscutively).
Normally, this triggers don't cause the FW to be restarted, but in
some cases that may be desired, so we recover from the problem. To
support this, add a flag that indicates that the FW should be
restarted when the trigger fires.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have a boolean variable for each cause.
This costs space, and requires to check each separately
when determining low latency.
Since we have another cause incoming, convert it to an enum.
While at it, move the retrieval of the prev value and the
assignment of the new value to be inside iwl_mvm_update_low_latency
and save the need for each caller to do it separately.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some geographic profiles require specific handling. For example ETSI
profile requires special channel access handling. Add geographic
profile information to MCC_UPDATE response to allow it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A lot of new PCI IDs were added for the 9000 series. Add them to the
list of supported PCI IDs.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove fragmented_dwell_time and add num_of_fragments to support
the new API version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW does not allocate quota air time for the binding of a station
MAC before iwlmvm indicates that it is associated. Currently iwlmvm
indicates that the MAC is associated only after hearing a beacon from
the AP. In case a deauthentication frame is sent before the MAC is
associated, the frame might not be sent as the corresponding binding
is not scheduled.
To handle such cases, set IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP in the
HW flags, requesting mac80211 to call the mgd_prepare_tx() callback
before transmitting a deauthentication frame if associated but no
beacon was heard from the AP.
In addition, do not warn in iwl_mvm_mac_mgd_prepare_tx() when already
associated as now the callback can be called also when associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for Optimized Connectivity Experience (OCE). Get
capabilities from the fw, expose them with nl80211, and enable them in
UMAC scan if the relevant nl80211 flags are set by the userspace.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the scan command API with support for adaptive dwell. Adaptive
dwell is a type of scan that dynamically changes the time it remains
on each channel listening for beacons or probe responses.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes iwl_mvm_disable_txq() may be called with mac80211_queue ==
IEEE80211_INVAL_HW_QUEUE, and this would cause us to use BIT(0xFF)
which is way too large for the u16 we used to store it in
hw_queue_to_mac820211. If this happens the following UBSAN warning
will be generated:
[ 167.185167] UBSAN: Undefined behaviour in drivers/net/wireless/intel/iwlwifi/mvm/utils.c:838:5
[ 167.185171] shift exponent 255 is too large for 64-bit type 'long unsigned int'
Fix that by checking that it is not IEEE80211_INVAL_HW_QUEUE and,
while at it, add a warning if the queue number is larger than
IEEE80211_MAX_QUEUES.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case debug configuration is started with LDBG cmd also start timestamp
marker for syncing logs witn the FW.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes future bail-outs from transmitting an AMSDU more
readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
An error TX completion (CQE) which arrived on a specific SQ indicates
that this SQ got moved by the hardware to error state, which means all
pending and incoming TX requests are dropped or will be dropped and no
further "Good" CQEs will be generated for that SQ.
Before this patch TX completions (CQEs) were not monitored and were
handled as a regular CQE. This caused the SQ to stay in an error state,
making it useless for xmiting new packets.
Mitigation plan:
In case of an error completion, schedule a recovery work which would do
the following:
- Mark the TXQ as DRV_XOFF to disable new packets to arrive from the
stack
- NAPI to flush all pending SQ WQEs (via flush_in_error_en bit) to
release SW and HW resources(SKB, DMA, etc) and have the SQ and CQ
consumer/producer indices synced.
- Modify the SQ state ERR -> RST -> RDY (restart the SQ).
- Reactivate the SQ and reset SQ cc and pc
If we identify two consecutive requests for SQ recover in less than
500 msecs, drop the recover request to avoid CPU overload, as this
scenario most likely happened due to a severe repeated bug.
In addition, add SQ recover SW counter to monitor successful recoveries.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Monitor and dump xmit error completions. In addition, add err_cqe
counter to track the number of error completion per send queue.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move query SQ state function from mlx5_ib to mlx5_core in order to
have it in shared code.
It will be used in a downstream patch from mlx5e.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver callback for handling TX timeout should access some internal
resources (SQ, CQ) in order to decide if the tx timeout work should be
scheduled. These resources might be unavailable if channels are closed
in parallel (ifdown for example).
The state lock is the mechanism to protect from such races.
Move all TX timeout logic to be in the work under a state lock.
In addition, Move the work from the global WQ to mlx5e WQ to make sure
this work is flushed when device is detached..
Also, move the mlx5e_tx_timeout_work code to be next to the TX timeout
NDO for better code locality.
Fixes: 3947ca1859 ("net/mlx5e: Implement ndo_tx_timeout callback")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commit 58d522912a ("net/mlx5e: Support TX packet copy into WQE")
introduced the max inline WQE as an ethtool tunable. One commit later,
that functionality was made dependent on BlueFlame.
Commit 6982ab6097 ("net/mlx5e: Xmit, no write combining") removed
BlueFlame support, and with it the max inline WQE.
This patch cleans up the leftovers from the removed feature.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a control private flag in ethtool to enable/disable
Striding RQ feature.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Do not implicit a call to mlx5e_init_rq_type_params() upon every
change in RQ type. It should be called only on channels creation.
Fixes: 2fc4bfb725 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
It can be derived from other params, calculate it
via the dedicated function when needed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce functions to calculate them when needed.
They can be derived from other params.
This will simplify transition between RQ configurations.
In general, any parameter that is not explicitly set
or controlled, but derived from other parameters,
should not have a control-path field itself, but a
getter function.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In copying skb header to skb->data, replace the call to
skb_copy_to_linear_data_offset() with a zero offset with
the call to the no-offset function skb_copy_to_linear_data().
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pass the base dma address and offset to dma_sync_single_range_for_cpu(),
instead of doing the pre-calculation.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clean it up as it's not in use.
Fixes: d9d9f156f3 ("net/mlx5e: Expand WQE stride when CQE compression is enabled")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We turn the feature off for servers with PCI BW bounded
by a threshold (16G) and lower than MAX LINK BW.
This improves the effectiveness of CQE compression feature,
that is defaulted to ON for the same case.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Get the link/pci speed query and logic into a single function.
Unify the heuristics and use a single PCI threshold (16G) for all.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The FLOW_RSS flag was causing us to insert UDP filters when TCP was wanted.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise races are possible between ethtool ops and
efx_ef10_rx_restore_rss_contexts().
Also, don't try to perform the restore on every reset, only after an MC
reboot, otherwise we'll leak RSS contexts on the NIC.
Fixes: 42356d9a13 ("sfc: support RSS spreading of ethtool ntuple filters")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If some other operation gets the MCDI lock ahead of us and performs an MC
reboot, then our attempt to insert the filter will fail with EINVAL,
because the destination VI (spec->dmaq_id, MC_CMD_FILTER_OP_IN_RX_QUEUE) does
not exist. But the caller's request (which might e.g. be an ethtool ntuple
request from userland) isn't invalid, it just got unlucky; so return EAGAIN.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this change, the spinlock efx->filter_lock is no longer used and is
thus removed.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx->filter_lock remains in place for use on farch, but EF10 now ignores it.
EFX_EF10_FILTER_FLAG_BUSY is no longer needed, hence it is removed.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having an efx->type->filter_rfs_insert() method, just use
workitems with a worker function that calls efx->type->filter_insert().
The only user of this is efx_filter_rfs(), which now queues a call to
efx_filter_rfs_work().
Similarly, efx_filter_rfs_expire() is now a worker function called on a
new channel->filter_work work_struct, so the method
efx->type->filter_rfs_expire_one() is no longer called in atomic context.
We also add a new mutex efx->rps_mutex to protect the RPS state (efx->
rps_expire_channel, efx->rps_expire_index, and channel->rps_flow_id) so
that the taking of efx->filter_lock can be moved to
efx->type->filter_rfs_expire_one().
Thus, all filter table functions are now called in a sleepable context,
allowing them to use sleeping locks in a future patch.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronous pernet_operations are not allowed anymore.
All are asynchronous. So, drop the structure member.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use relaxed I/O on the hot path. This achieves significant performance
improvements. On a 10G link, this makes a basic iperf TCP test go from
an average of 4.5 Gbits/sec to about 9.40 Gbits/sec.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Maxime: Commit message, cosmetic changes]
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c5ad119fb6
("net: sched: pfifo_fast use skb_array") driver is exposed
to an issue where it is hitting NULL skbs while handling TX
completions. Driver uses mmiowb() to flush the writes to the
doorbell bar which is a write-combined bar, however on x86
mmiowb() does not flush the write combined buffer.
This patch fixes this problem by replacing mmiowb() with wmb()
after the write combined doorbell write so that writes are
flushed and synchronized from more than one processor.
V1->V2:
-------
This patch was marked as "superseded" in patchwork.
(Not really sure for what reason).Resending it as v2.
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_delete_all_resources_for_slave in resource tracker should free all
memory allocated for a slave.
While releasing memory of fs_rule, it misses releasing memory of
fs_rule->mirr_mbox.
Fixes: 78efed2751 ('net/mlx4_core: Support mirroring VF DMFS rules on both ports')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global pause and PFC configuration should be mutually exclusive (i.e. only
one of them at most can be set). However, once PFC was turned off,
driver automatically turned Global pause on. This is a bug.
Fix the driver behaviour to turn off PFC/Global once the user turned the
other on.
This also fixed a weird behaviour that at a current time, the profile
had both PFC and global pause configuration turned on, which is
Hardware-wise impossible and caused returning false positive indication
to query tools.
In addition, fix error code when setting global pause or PFC to change
metadata only upon successful change.
Also, removed useless debug print.
Fixes: af7d518526 ("net/mlx4_en: Add DCB PFC support through CEE netlink commands")
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauV9vAAoJEEg/ir3gV/o+Dw4H/0oT5mXUQuEdXDw3y3JtodMA
VEYjPt7EH+X0RUZcO9xkiZGwtfh5+Bk7oDB4uy5IzGdAAEgCX5VvR+m3jnbRfORm
WztMGAy1fiswavYf5tYDBjSM0HSLLKxCUJr0FcPG5DG5Fe90n0DvP2Xj0l+6R0Og
7SSwiK2UXrnfcAvDTFUgj0k2IEAUH1/dCwfruVvt4H4R1Pp6PQGBEfuEc3Jra4wi
9wYik10xQ/MTVxEtw3Om+D7CJzvSiz6DOk2Pp0Ls+1RKvKrlqWyiAOR7nswHRgIk
hnqNV3t47FP1W4bp1YpMjeQ0yi2xcJQPBzRdaf22MDaUiEBLFQBqiINPsOaniL0=
=Tqzl
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-03-23
The following series includes fixes for mlx5 netdev and eswitch.
v1->v2:
- Fixed commit message quotation marks in patch #7
For -stable v4.12
('net/mlx5e: Avoid using the ipv6 stub in the TC offload neigh update path')
('net/mlx5e: Fix traffic being dropped on VF representor')
For -stable v4.13
('net/mlx5e: Fix memory usage issues in offloading TC flows')
('net/mlx5e: Verify coalescing parameters in range')
For -stable v4.14
('net/mlx5e: Don't override vport admin link state in switchdev mode')
For -stable v4.15
('108b2b6d5c02 net/mlx5e: Sync netdev vxlan ports at open')
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes misc updates for mlx5 core and netdev dirver,
Highlights:
From Inbar, three patches to add support for PFC stall prevention
statistics and enable/disable through new ethtool tunable, as requested
from previous submission.
From Moshe, four patches, added more drop counters:
- drop counter for netdev steering miss
- drop counter for when VF logical link is down
- drop counter for when netdev logical link is down.
From Or, three patches to support vlan push/pop offload via tc HW action,
for newer HW (Connectx-5 and onward) via HW steering flow actions rather
than the emulated path for the older HW brands.
And five more misc small trivial patches.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauVxkAAoJEEg/ir3gV/o+Oi4H/1Mzv+XEuHLwVJHpzMNVLVeR
EK1GDW3724zjY24Iy+9FRppL1mV0hY3aw1qhD+rUmUKQx+Q3OBrH1WN2QJkjBkM9
i60ygFLTHvcHyPFmHtPzCckO7ODdWsXSlEwsl8kCSITQTn1Mjf6v7Mogd0CLCbwN
iu8ocpHTD+/whE5gq9aDDrGtuzgJbPiRqavvsof9pc2g1JlnvtHs9xoiN+vzoqIa
9lGS+2UM2+wFw9rMtbdaqtfVPsupMeEdGZ98chn0gpWshOvOda5NuRE59M+5un5E
C3nJ4Js//PLkvQ9Nu7+goXtbfPLCxvcuurid5TM2Su9hmD+9Us223TcAvdpOMoY=
=VdCO
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-03-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-22 (Misc updates)
This series includes misc updates for mlx5 core and netdev dirver,
Highlights:
From Inbar, three patches to add support for PFC stall prevention
statistics and enable/disable through new ethtool tunable, as requested
from previous submission.
From Moshe, four patches, added more drop counters:
- drop counter for netdev steering miss
- drop counter for when VF logical link is down
- drop counter for when netdev logical link is down.
From Or, three patches to support vlan push/pop offload via tc HW action,
for newer HW (Connectx-5 and onward) via HW steering flow actions rather
than the emulated path for the older HW brands.
And five more misc small trivial patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Napi is checking Tx queue status and waking the Tx queue if required.
Same operation is being done while freeing every Tx buffer.
So removed the duplicate operation of checking Tx queue status from the Tx
buffer free functions.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_set_drvdata() is called only after registering the net_device,
therefore we could run into a NPE if one of the functions using
driver_data is called before it's set.
Fix this by calling pci_set_drvdata() before registering the
net_device.
This fix is a candidate for stable. As far as I can see the
bug has been there in kernel version 3.2 already, therefore
I can't provide a reference which commit is fixed by it.
The fix may need small adjustments per kernel version because
due to other changes the label which is jumped to if
register_netdev() fails has changed over time.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:508:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helper functions that search for given entries in the TCAM filter
on PPv2 controller make use of dynamically alloced temporary variables,
allocated with GFP_KERNEL. These functions can be called in atomic
context, and dynamic alloc is not really needed in these cases anyways.
This commit gets rid of dynamic allocs and use stack allocation in the
following functions, and where they're used :
- mvpp2_prs_flow_find
- mvpp2_prs_vlan_find
- mvpp2_prs_double_vlan_find
- mvpp2_prs_mac_da_range_find
For all these functions, instead of returning an temporary object
representing the TCAM entry, we simply return the TCAM id that matches
the requested entry.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_hw_read function uses the 'index' field of the struct
mvpp2_prs_entry to initialize the rest of the fields. This makes it
unclear from a caller's perspective, who needs to manipulate a struct
that is not entirely initialized.
This commit makes it an init function for prs_entry, by passing it the
index as a parameter. The function now zeroes the entry, and sets the
index field before doing all other init from HW.
The function is renamed 'mvpp2_prs_init_from_hw' to make that clear.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-03-26
This series contains updates to i40e only.
Jake provides several patches which remove the need for cmpxchg64(),
starting with moving I40E_FLAG_[UDP]_FILTER_SYNC from pf->flags to pf->state
since they are modified during run time possibly when the RTNL lock is not
held so they should be a state bits and not flags. Moved additional
"flags" which should be state fields, into pf->state. Ensure we hold
the RTNL lock for the entire sequence of preparing for reset and when
resuming, which will protect the flags related to interrupt scheme under
RTNL lock so that their modification is properly threaded. Finally,
cleanup the use of cmpxchg64() since it is no longer needed. Cleaned up
the holes in the feature flags created my moving some flags to the state
field.
Björn Töpel adds XDP_REDIRECT support as well as tweaking the page
counting for XDP_REDIRECT so that it will function properly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a theoretical NULL pointer dereferencing in mt76x2_tx routine that
can occurs for injected frames in a monitor vif since vif pointer could
be NULL for that interfaces
Fixes: 2340523646 ("mt76: fix transmission of encrypted mgmt frames")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use mt76_poll_msec() in mt76pci_load_firmware to check if the firmware
has been started instead of explicitly poll MCU running register
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcms_ucode_init_buf() duplicates the ucode chunks via kmemdup()
with GFP_ATOMIC as a precondition of wl->lock acquired. This caused
allocation failures sometimes as reported in the bugzilla below.
When looking at the the real usage, one can find that it's called
solely from brcms_request_fw(), and it's obviously outside the lock.
Hence we can use GFP_KERNEL there safely for avoiding such allocation
errors.
Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=1085174
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This field did not have kerneldoc description so adding it now.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function was pretty minimal and now it is called only from one
place so just get rid of it.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function is no longer used so removing it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This changes the bus layer api by having the caller provide an
extension. With this the callback can use brcmf_fw_alloc_request()
to get the needed firmware name.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_fw_alloc_request() takes a list of required files
and allocated the struct brcmf_fw_request instance accordingly. The
request can be modified by the caller before being passed to the
brcmf_fw_request_firmwares() function.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the function brcmf_fw_get_firmwares() a bit more easy to extend
using a structure to pass the request parameters.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of defining individual filenames for firmware and nvram
use a basename and derive the names from that.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver used to create a brcmfmac dir entry at the top level
debugfs mount point. This moves the debugfs entries into the
wiphy debugfs dir entry.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework the driver so the wiphy instance holds the main driver information
in its private buffer. Previously it held struct brcmf_cfg80211_info
instance so a bit of reorg was needed. This was done so that the wiphy
name or its parent device can be shown in debug output.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When logging the chip id/revision information make use of
brcmf_chip_name() so it is always the same.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The chip id can either be four or five digits. For the chip name either
the hexadecimal value needs to be taken (four digits) or the decimal
value (five digits). The function brcmf_chip_name() does this conversion
so use it to store the name in driver revision info.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of a linux error brcmf_fil_cmd_data() blurts an error message
in which the error code is translated to an error string. However, it
maps it to a firmware error string which should not happen. Simply
print only the numeric error code and be done with it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in RT_TRACE message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net?
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct comment. Set bit 3 and bit 4 of 0x0005 register (REG_APS_FSMCO + 1)
to 0 which means disable WL suspend, not enable WL suspend.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex support multiple platforms, but this drivers doesn't support full
functions yet, so this commit adds dummy definitions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New constant and variables definitions are used by btcoex of 8822b, so
this commit add them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In connection notify v1, btcoex only need to know start/end association,
and it will discriminate 2G and 5G band in v2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Normal LPS is decomposed into pre- and post- parts, so we can issue H2C
with TDMA parameters in the "critical section" that dirver can't change
LPS state at the moment.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get phydm's counter and version from the module phydm that is not
submitted so we implement dummy functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The btcoex use the rate to rsolve IOT issue that some APs reduce TX
rate quickly, so it uses the RX rate as a clue to decide TDMA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger#lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex does different decision according to MCC or SCC status, but
driver is still SCC currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add customer_id field in structure, and then this is a clue to implement
the behavior defined by vendor LENOVO_CHINA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex uses dm's counters to check the environment is noisy or not. If it
is clean, btcoex set more time slots to WiFi so that it can transmit as
soon as possible. That will save time, and BT will have more time slots
after WiFi traffic is complete.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports "rtl_is_special_data() warn: inconsistent indenting", but
it is an obvious redundant statement so remove it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sparse reports some functions were not declared, so add 'static' as
modifier. Remove an unused function btc8821a1ant_is_wifi_status_changed()
exposed due to 'static'.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable buffer_size is re-assigned the same value, this duplicated
assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/rsi/rsi_91x_usb.c:140:4: warning: Value stored
to 'buffer_size' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently rsi code uses a VLA based on a function argument to
`rsi_sdio_load_data_master_write()`. The function call chain is
Both these functions
rsi_sdio_reinit_device()
rsi_probe()
start the call chain:
rsi_hal_device_init()
rsi_load_fw()
auto_fw_upgrade()
ping_pong_write()
rsi_sdio_load_data_master_write()
[Without familiarity with the code] it appears that none of the 4 locks
mutex
rx_mutex
tx_mutex
tx_bus_mutex
are held when `rsi_sdio_load_data_master_write()` is called. It is therefore
safe to use kmalloc with GFP_KERNEL.
We can avoid using the VLA by using `kmalloc()` and free'ing the memory on all
exit paths.
Change buffer from 'u8 array' to 'u8 *'. Call `kmalloc()` to allocate memory for
the buffer. Using goto statement to call `kfree()` on all return paths.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc()` however this code is only called on initialization
(and re-initialization) so this overhead should not degrade performance.
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the following sparse warning in mwifiex_cmd_append_11n_tlv:
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: right side has type int
Fixes: 77423fa739 ("mwifiex: fix incorrect ht capability problem")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes spelling typos found in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The linkage between the bluetooth driver and the wireless
driver is not defined properly, leading to build problems
such as:
warning: (BT_HCIRSI) selects RSI_COEX which has unmet direct dependencies (NETDEVICES && WLAN && WLAN_VENDOR_RSI && BT_HCIRSI && RSI_91X)
drivers/net/wireless/rsi/rsi_91x_main.o: In function `rsi_read_pkt':
(.text+0x205): undefined reference to `rsi_bt_ops'
As the dependency is actually the reverse (RSI_91X uses
the BT_RSI driver, not the other way round), this changes
the dependency to match, and enables the bluetooth driver
from the RSI_COEX symbol.
Fixes: 38aa4da504 ("Bluetooth: btrsi: add new rsi bluetooth driver")
Acked-by; Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-03-26
This patch series adds the ice driver, which will support the Intel(R)
E800 Series of network devices.
This is the first phase in the release of this driver where we implement
basic transmit and receive. The idea behind the multi-phase release is to
aid in code review as well as testing. Subsequent phases will implement
advanced features (like SR-IOV, tunnelling, flow director, QoS, etc.) that
build upon the previous phase(s). Each phase will be submitted as a patch
series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver now acts upon the XDP_REDIRECT return action. Two new ndos
are implemented, ndo_xdp_xmit and ndo_xdp_flush.
XDP_REDIRECT action enables XDP program to redirect frames to other
netdevs.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit tweaks the page counting for XDP_REDIRECT to function
properly. XDP_REDIRECT support will be added in a future commit.
The current page counting scheme assumes that the reference count
cannot decrease until the received frame is sent to the upper layers
of the networking stack. This assumption does not hold for the
XDP_REDIRECT action, since a page (pointed out by xdp_buff) can have
its reference count decreased via the xdp_do_redirect call.
To work around that, we now start off by a large page count and then
don't allow a refcount less than two.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the gaps created by the recent refactor of various feature flags
that have moved to the state field. Use only a u32 now that we have
fewer than 32 flags in the field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When mlx5_core is loaded it is expected to sync ports
with all vxlan devices so it can support vxlan encap/decap.
This is done via udp_tunnel_get_rx_info(). Currently this
call is set in mlx5e_nic_enable() and if the netdev is not in
NETREG_REGISTERED state it will not be called.
Normally on load the netdev state is not NETREG_REGISTERED
so udp_tunnel_get_rx_info() will not be called.
Moving udp_tunnel_get_rx_info() to mlx5e_open() so
it will be called on netdev UP event and allow encap/decap.
Fixes: 610e89e05c ("net/mlx5e: Don't sync netdev state when not registered")
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we use the global ipv6_stub var to access the ipv6 global
nd table. This practice gets us to troubles when the stub is only partially
set e.g when ipv6 is loaded under the disabled policy. In this case, as of commit
343d60aada ("ipv6: change ipv6_stub_impl.ipv6_dst_lookup to take net argument")
the stub is not null, but stub->nd_tbl is and we crash.
As we can access the ipv6 nd_tbl directly, the fix is just to avoid the
reference through the stub. There is one place in the code where we
issue ipv6 route lookup and keep doing it through the stub, but that
mentioned commit makes sure we get -EAFNOSUPPORT from the stack.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For NIC flows, the parsed attributes are not freed when we exit
successfully from mlx5e_configure_flower().
There is possible double free for eswitch flows. If error is returned
from rhashtable_insert_fast(), the parse attrs will be freed in
mlx5e_tc_del_flow(), but they will be freed again before exiting
mlx5e_configure_flower().
To fix both issues we do the following:
(1) change the condition that determines if to issue the free call to
check if this flow is NIC flow, or it does not have encap action.
(2) reorder the code such that that the check and free calls are done
before we attempt to add into the hash table.
Fixes: 232c001398 ('net/mlx5e: Add support to neighbour update flow')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Increase representor netdev RQ size to avoid dropped packets.
The current size (two) is just too small to keep up with
conventional slow path traffic patterns.
Also match the SQ size to the RQ size.
Fixes: cb67b83292 ("net/mlx5e: Introduce SRIOV VF representors")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add check of coalescing parameters received through ethtool are within
range of values supported by the HW.
Driver gets the coalescing rx/tx-usecs and rx/tx-frames as set by the
users through ethtool. The ethtool support up to 32 bit value for each.
However, mlx5 modify cq limits the coalescing time parameter to 12 bit
and coalescing frames parameters to 16 bits.
Return out of range error if user tries to set these parameters to
higher values.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add dependancy for switchdev to be congfigured as any user-space control
plane SW is expected to use the HW switchdev ID to locate the representors
related to VFs of a certain PF and apply SW/offloaded switching on them.
Fixes: e80541ecab ('net/mlx5: Add CONFIG_MLX5_ESWITCH Kconfig')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
SQs are 32 and not 16 bits, hence it's wrong to use only 16 bits to
store the sq number for which are going to set steering rule, fix that.
Fixes: cb67b83292 ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The vport admin original link state will be re-applied after returning
back to legacy mode, it is not right to change the admin link state value
when in switchdev mode.
Use direct vport commands to alter logical vport state in netdev
representor open/close flows rather than the administrative eswitch API.
Fixes: 20a1ea6747 ('net/mlx5e: Support VF vport link state control for SRIOV switchdev mode')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now that the only places which modify flags are either (a) during
initialization prior to creating a netdevice, or (b) while holding the
rtnl lock, we no longer need the cmpxchg64 call in i40e_set_priv_flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we suspend and resume, we need to clear and re-enable the interrupt
scheme. This was previously not done while holding the RTNL lock, which
could be problematic, because we are actually destroying and re-creating
queues.
Hold the RTNL lock for the entire sequence of preparing for reset, and
when resuming. This additionally protects the flags related to interrupt
scheme under RTNL lock so that their modification is properly threaded.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The iWarp client flags are all potentially changed when the RTNL lock is
not held, so they should not be part of the pf->flags variable. Instead,
move them into the state field so that we can use atomic bit operations.
This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag is modified outside of the RTNL lock and thus should not be
part of the pf->flags variable.
Use a state bit instead, so that we can use atomic bit operations.
This is part of a larger effort to remove cmpxchg64 in
i40e_set_priv_flags()
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We support outer VLAN offload in driver and HW regardless of whether
an encapsulation is present in the next headers.
Exposing this in hw_enc_features will allow us to offload outer VLANs
in cases where encapsulation protocols like VXLAN and IPsec are used.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a new macro to prevent copy-pasting the same code for each new
feature.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The function is used in en_main.c only, we can make it static and remove
its declaration from en.h
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
ethtool core code makes sure data isn't NULL before calling
get_ethtool_stats, testing it again in the driver is redundant.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The system with CONFIG_UBSAN enabled on produces the following error
during driver initialization. The reason to it that max_reg_cmds can be
larger enough to cause to "1 << max_reg_cmds" overflow the unsigned long.
================================================================================
UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1805:42
signed integer overflow:
-2147483648 - 1 cannot be represented in type 'int'
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc2-00032-g06cda2358d9b-dirty #724
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0xe9/0x18f
? dma_virt_alloc+0x81/0x81
ubsan_epilogue+0xe/0x4e
handle_overflow+0x187/0x20c
mlx5_cmd_init+0x73a/0x12b0
mlx5_load_one+0x1c3d/0x1d30
init_one+0xd02/0xf10
pci_device_probe+0x26c/0x3b0
driver_probe_device+0x622/0xb40
__driver_attach+0x175/0x1b0
bus_for_each_dev+0xef/0x190
bus_add_driver+0x2db/0x490
driver_register+0x16b/0x1e0
__pci_register_driver+0x177/0x1b0
init+0x6d/0x92
do_one_initcall+0x15b/0x270
kernel_init_freeable+0x2d8/0x3d0
kernel_init+0x14/0x190
ret_from_fork+0x24/0x30
================================================================================
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we are emulating the offload of vlan push/pop actions using
global setup as done by commit f5f8247609 ("net/mlx5: E-Switch, Support
VLAN actions in the offloads mode"). With newer NICs, we can apply a flow
action for that matter, do that while keeping the emulated path for the
older HW brands.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Newer NICs (ConnectX-5 and onward) can apply vlan pop or push as an
action taking place during flow steering. Add the core bits for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Align the checks for modify header and encap actions with the
rest of the code.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Rx interface down dropped packets - counts packets which were received
while the ETH interface was down.
This counter will be shown on ethtool as a new counter called
rx_if_down_packets.
The implementation allocates a q_counter for drop rq which gets all the
received traffic while the interface is down.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets dropped while vport down statistics:
Rx dropped while vport down - counts packets which were steered by
e-switch to a vport, but dropped since the vport was down. This counter
will be shown on ip link tool as part of the vport rx_dropped counter.
Tx dropped while vport down - counts packets which were transmitted by
a vport, but dropped due to vport logical link down. This counter
will be shown on ip link tool as part of the vport tx_dropped counter.
The counters are read from FW by command QUERY_VNIC_ENV.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added the following packets drop counter:
Rx steering missed dropped packets - counts packets which were dropped
due to miss on NIC rx steering rules.
This counter will be shown on ethtool as a new counter called
rx_steer_missed_packets.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for new FW command QUERY_VNIC_ENV.
The command is used by the driver to query vnic diagnostic statistics
from FW.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement set/get functions to configure PFC stall prevention
timeout by tunables api through ethtool.
By default the stall prevention timeout is configured to 8 sec.
Timeout range is: 80-8000 msec.
Enabling stall prevention with the auto timeout will set
the timeout to 100 msec.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The two Flow Directory auto disable flags are used at run time to mark
when the flow director features needed to be disabled. Thus the flags
could change even when the RTNL lock is not held.
They also have some code constructions which really should be
test_and_set or test_and_clear using atomic bit operations.
Create new state fields to mark this, and stop including them in
pf->flags.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag is modified during run time, possibly even when the RTNL lock
is not held. Additionally it has a few places which should be using
test_and_set or test_and_clear atomic bit operations.
Create a new state bit __I40E_UDP_SYNC_PENDING and use it instead of the
ole I40E_FLAG_UDP_FILTER_SYNC flag.
This is part of a larger effort to remove the need for using cmpxchg64
in i40e_set_priv_flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the needed capability bit and counters to device spec description.
Expose the following two counters in ethtool:
tx_pause_storm_warning_events: when the device is stalled for a period
longer than a pre-configured watermark, the counter increase, allowing
the debug utility an insight into current device status.
tx_pause_storm_error_events: when the device is stalled for a period
longer than a pre-configured timeout, the pause transmission is disabled,
and the counter increase.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The I40E_FLAG_FILTER_SYNC flag is modified during run time possibly when
the RTNL lock is not held. Thus, it should not be part of pf->flags, and
instead should be using atomic bit operations in the pf->state field.
Create a __I40E_MACVLAN_SYNC_PENDING state bit, and use it instead of
the old I40E_FLAG_FILTER_SYNC flag.
This is part of a larger effort to remove the need for cmpxchg64 in
i40e_set_priv_flags().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements multiple pieces of functionality:
1. Added ice_vsi_sync_filters, which is called through the service task
to push filter updates to the hardware.
2. Add support to enable/disable promiscuous mode on an interface.
Enabling/disabling promiscuous mode on an interface results in
addition/removal of a promisc filter rule through ice_vsi_sync_filters.
3. Implement handlers for ndo_set_mac_address, ndo_change_mtu,
ndo_poll_controller and ndo_set_rx_mode.
This patch also marks the end of the driver addition by bumping up the
driver version.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link events are posted to a PF's admin receive queue (ARQ). This patch
adds the ability to detect and process link events.
This patch also adds the ability to process resets.
The driver can process the following resets:
1) EMP Reset (EMPR)
2) Global Reset (GLOBR)
3) Core Reset (CORER)
4) Physical Function Reset (PFR)
EMPR is the largest level of reset that the driver can handle. An EMPR
resets the manageability block and also the data path, including PHY and
link for all the PFs. The affected PFs are notified of this event through
a miscellaneous interrupt.
GLOBR is a subset of EMPR. It does everything EMPR does except that it
doesn't reset the manageability block.
CORER is a subset of GLOBR. It does everything GLOBR does but doesn't
reset PHY and link.
PFR is a subset of CORER and affects only the given physical function.
In other words, PFR can be thought of as a CORER for a single PF. Since
only the issuing PF is affected, a PFR doesn't result in the miscellaneous
interrupt being triggered.
All the resets have the following in common:
1) Tx/Rx is halted and all queues are stopped.
2) All the VSIs and filters programmed for the PF are lost and have to be
reprogrammed.
3) Control queue interfaces are reset and have to be reprogrammed.
In the rebuild flow, control queues are reinitialized, VSIs are reallocated
and filters are restored.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the ability for a VSI to use multiple Tx queues. More
specifically, the patch
1) Provides the ability to update the Tx scheduler tree in the
firmware. The driver can configure the Tx scheduler tree by
adding/removing multiple Tx queues per TC per VSI.
2) Allows a VSI to reconfigure its Tx queues during runtime.
3) Synchronizes the Tx scheduler update operations using locks.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for VLANs. When a VLAN is created a switch filter
is added to direct the VLAN traffic to the corresponding VSI. When a VLAN
is deleted, the filter is deleted as well.
This patch also adds support for the following hardware offloads.
1) VLAN tag insertion/stripping
2) Receive Side Scaling (RSS)
3) Tx checksum and TCP segmentation
4) Rx checksum
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements ice_start_xmit (the handler for ndo_start_xmit) and
related functions. ice_start_xmit ultimately calls ice_tx_map, where the
Tx descriptor is built and posted to the hardware by bumping the ring tail.
This patch also implements ice_napi_poll, which is invoked when there's an
interrupt on the VSI's queues. The interrupt can be due to either a
completed Tx or an Rx event. In case of a completed Tx/Rx event, resources
are reclaimed. Additionally, in case of an Rx event, the skb is fetched
and passed up to the network stack.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch configures the VSIs to be able to send and receive
packets by doing the following:
1) Initialize flexible parser to extract and include certain
fields in the Rx descriptor.
2) Add Tx queues by programming the Tx queue context (implemented in
ice_vsi_cfg_txqs). Note that adding the queues also enables (starts)
the queues.
3) Add Rx queues by programming Rx queue context (implemented in
ice_vsi_cfg_rxqs). Note that this only adds queues but doesn't start
them. The rings will be started by calling ice_vsi_start_rx_rings on
interface up.
4) Configure interrupts for VSI queues.
5) Implement ice_open and ice_stop.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A VSI needs traffic directed towards it. This is done by programming
filter rules on the switch (embedded vSwitch) element in the hardware,
which connects the VSI to the ingress/egress port.
This patch introduces data structures and functions necessary to add
remove or update switch rules on the switch element. This is a pretty low
level function that is generic enough to add a whole range of filters.
This patch also introduces two top level functions ice_add_mac and
ice_remove mac which through a series of intermediate helper functions
eventually call ice_aq_sw_rules to add/delete simple MAC based filters.
It's worth noting that one invocation of ice_add_mac/ice_remove_mac
is capable of adding/deleting multiple MAC filters.
Also worth noting is the fact that the driver maintains a list of currently
active filters, so every filter addition/removal causes an update to this
list. This is done for a couple of reasons:
1) If two VSIs try to add the same filters, we need to detect it and do
things a little differently (i.e. use VSI lists, described below) as
the same filter can't be added more than once.
2) In the event of a hardware reset we can simply walk through this list
and restore the filters.
VSI Lists:
In a multi-VSI situation, it's possible that multiple VSIs want to add the
same filter rule. For example, two VSIs that want to receive broadcast
traffic would both add a filter for destination MAC ff:ff:ff:ff:ff:ff.
This can become cumbersome to maintain and so this is handled using a
VSI list.
A VSI list is resource that can be allocated in the hardware using the
ice_aq_alloc_free_res admin queue command. Simply put, a VSI list can
be thought of as a subscription list containing a set of VSIs to which
the packet should be forwarded, should the filter match.
For example, if VSI-0 has already added a broadcast filter, and VSI-1
wants to do the same thing, the filter creation flow will detect this,
allocate a VSI list and update the switch rule so that broadcast traffic
will now be forwarded to the VSI list which contains VSI-0 and VSI-1.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces data structures and functions to alloc/free
VSIs. The driver represents a VSI using the ice_vsi structure.
Some noteworthy points about VSI allocation:
1) A VSI is allocated in the firmware using the "add VSI" admin queue
command (implemented as ice_aq_add_vsi). The firmware returns an
identifier for the allocated VSI. The VSI context is used to program
certain aspects (loopback, queue map, etc.) of the VSI's configuration.
2) A VSI is deleted using the "free VSI" admin queue command (implemented
as ice_aq_free_vsi).
3) The driver represents a VSI using struct ice_vsi. This is allocated
and initialized as part of the ice_vsi_alloc flow, and deallocated
as part of the ice_vsi_delete flow.
4) Once the VSI is created, a netdev is allocated and associated with it.
The VSI's ring and vector related data structures are also allocated
and initialized.
5) A VSI's queues can either be contiguous or scattered. To do this, the
driver maintains a bitmap (vsi->avail_txqs) which is kept in sync with
the firmware's VSI queue allocation imap. If the VSI can't get a
contiguous queue allocation, it will fallback to scatter. This is
implemented in ice_vsi_get_qs which is called as part of the VSI setup
flow. In the release flow, the VSI's queues are released and the bitmap
is updated to reflect this by ice_vsi_put_qs.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch continues the initialization flow as follows:
1) Allocate and initialize necessary fields (like vsi, num_alloc_vsi,
irq_tracker, etc) in the ice_pf instance.
2) Setup the miscellaneous interrupt handler. This also known as the
"other interrupt causes" (OIC) handler and is used to handle non
hotpath interrupts (like control queue events, link events,
exceptions, etc.
3) Implement a background task to process admin queue receive (ARQ)
events received by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to continue the initialization flow as follows:
1) Get PHY/link information and store it
2) Get default scheduler tree topology and store it
3) Get the MAC address associated with the port and store it
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds to the initialization flow by getting switch
configuration, scheduler configuration and device capabilities.
Switch configuration:
On boot, an L2 switch element is created in the firmware per physical
function. Each physical function is also mapped to a port, to which its
switch element is connected. In other words, this switch can be visualized
as an embedded vSwitch that can connect a physical function's virtual
station interfaces (VSIs) to the egress/ingress port. Egress/ingress
filters will be eventually created and applied on this switch element.
As part of the initialization flow, the driver gets configuration data
from this switch element and stores it.
Scheduler configuration:
The Tx scheduler is a subsystem responsible for setting and enforcing QoS.
As part of the initialization flow, the driver queries and stores the
default scheduler configuration for the given physical function.
Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, VSIs, etc). This information is obtained from
the firmware and stored by the driver.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new trap for PIMv6 packets. As PIM already has a designated trap
group [ & rate limiter], simply use the same for PIMv6 as well.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following previous patches driver is ready to handle notifications
arriving from ip6mr - start processing those when they arrive following
the same manner ipmr currently goes through.
This should enable driver to start offloading ipv6 multicast routes.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the various operation structures meant for IPv6 with logic
unique to that protocol suite.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spectrum_router and spectrum_mr have several APIs that are used to
manipulate configurations originating from ipmr fib notifications.
Following previous patches all the protocol-specifics that are necessary
for the configuration are hidden within spectrum_mr. This allows us to
clean the API and make sure that other than choosing the mr_table based
on the fib notification family, spectrum_router wouldn't care about the
source of the notification when passing it onward to spectrum_mr.
This would later allow us to leverage the same code for fib
notifications originating from ip6mr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current multicast routing logic in driver assumes it's always meant to
deal with IPv4 multicast routes, leaving several placeholders for
later IPv6 support [currently usually WARN()].
This patch changes the driver's internal multicast route struct into
holding a common mr_mfc instead of the IPv4 mfc_cache.
The various placeholders are grouped into 2:
- Functions that require only the common bits; These remain and the
restriction for IPv4-only is lifted.
- Function that require IPv4-specifics - for handling these functions
we add sets of operations that encapsulate the protocol differences
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A step toward offloading IPv6 routing, this adds an additional
multicast routing table meant for IPv6 [with its underlying TCAM
region] and populates the default rule for IPv6 multicast packets.
Following this, ingress IPv6 multicast packets would be trapped and
delivered to the host CPU.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c011ec1bbf ("mlxsw: spectrum: Add the multicast routing
offloading logic") spectrum_mr did not populate the protocol portion of
the catcahall_route_params; mr-tcam logic worked correctly for ipv4
since the enum value for MLXSW_SP_L3_PROTO_IPV4 is '0'.
Explicitly fill the protocol as we'll soon need to differentiate between
ipv4 and ipv6.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields for the rmft register necessary for setting the IPv6
multicast FIB table. Add a matching wrapper function for filling
the register in the IPv6 scenario.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to what was done in commit 4af5964e58 ("mlxsw: reg:
Configure RIF to forward IPv4 multicast packets by default") we now set
two additional bits to allow IPv6 multicast forwarding.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ipmr and ip6mr are using the same mr_mfc struct at their core, we
can now refactor the ipmr_cache_{hold,put} logic and apply refcounting
to both ipmr and ip6mr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like vif notifications, move the notifier struct for MFC as well as its
helpers into a common file; Currently they're only used by ipmr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's required to create a modules.alias via MODULE_DEVICE_TABLE helper
for the OF platform driver. Otherwise, module autoloading cannot work.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_ALIAS exports information to allow the module to be auto-loaded at
boot for the drivers registered using legacy platform registration.
However, currently the driver is always used by DT-only platform,
MODULE_ALIAS is redundant and should be removed properly.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ip fragmentation match offloading for both IPv4 and IPv6. Allows
offloading frag, nofrag, first and nofirstfrag classification.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactored shared ip header code for IPv4 and IPv6 in match offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements multiple pieces of the initialization flow
as follows:
1) A reset is issued to ensure a clean device state, followed
by initialization of admin queue interface.
2) Once the admin queue interface is up, clear the PF config
and transition the device to non-PXE mode.
3) Get the NVM configuration stored in the device's non-volatile
memory (NVM) using ice_init_nvm.
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is needed to support the modem found in HP EliteBook 820 G3.
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix as in 'bonding: move dev_mc_sync after master_upper_dev_link
in bond_enslave' is needed for team driver.
The panic can be reproduced easily:
ip link add team1 type team
ip link set team1 up
ip link add link team1 vlan1 type vlan id 80
ip link set vlan1 master team1
Fixes: cb41c997d4 ("team: team should sync the port's uc/mc addrs when add a port")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_set_promiscuity(1) succeeds but dev_set_allmulti(1) fails,
dev_set_promiscuity(-1) should be done before going to the err path.
Otherwise, dev->promiscuity will leak.
Fixes: 7e1a1ac1fb ("bonding: Check return of dev_set_promiscuity/allmulti")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Beniamino found a crash when adding vlan as slave of bond which is also
the parent link:
ip link add bond1 type bond
ip link set bond1 up
ip link add link bond1 vlan1 type vlan id 80
ip link set vlan1 master bond1
The call trace is as below:
[<ffffffffa850842a>] queued_spin_lock_slowpath+0xb/0xf
[<ffffffffa8515680>] _raw_spin_lock+0x20/0x30
[<ffffffffa83f6f07>] dev_mc_sync+0x37/0x80
[<ffffffffc08687dc>] vlan_dev_set_rx_mode+0x1c/0x30 [8021q]
[<ffffffffa83efd2a>] __dev_set_rx_mode+0x5a/0xa0
[<ffffffffa83f7138>] dev_mc_sync_multiple+0x78/0x80
[<ffffffffc084127c>] bond_enslave+0x67c/0x1190 [bonding]
[<ffffffffa8401909>] do_setlink+0x9c9/0xe50
[<ffffffffa8403bf2>] rtnl_newlink+0x522/0x880
[<ffffffffa8403ff7>] rtnetlink_rcv_msg+0xa7/0x260
[<ffffffffa8424ecb>] netlink_rcv_skb+0xab/0xc0
[<ffffffffa83fe498>] rtnetlink_rcv+0x28/0x30
[<ffffffffa8424850>] netlink_unicast+0x170/0x210
[<ffffffffa8424bf8>] netlink_sendmsg+0x308/0x420
[<ffffffffa83cc396>] sock_sendmsg+0xb6/0xf0
This is actually a dead lock caused by sync slave hwaddr from master when
the master is the slave's 'slave'. This dead loop check is actually done
by netdev_master_upper_dev_link. However, Commit 1f718f0f4f ("bonding:
populate neighbour's private on enslave") moved it after dev_mc_sync.
This patch is to fix it by moving dev_mc_sync after master_upper_dev_link,
so that this loop check would be earlier than dev_mc_sync. It also moves
if (mode == BOND_MODE_8023AD) into if (!bond_uses_primary) clause as an
improvement.
Note team driver also has this issue, I will fix it in another patch.
Fixes: 1f718f0f4f ("bonding: populate neighbour's private on enslave")
Reported-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_vids_add_by_dev is called right after dev hwaddr sync, so on
the err path it should unsync dev hwaddr. Otherwise, the slave
dev's hwaddr will never be unsync when this err happens.
Fixes: 1ff412ad77 ("bonding: change the bond's vlan syncing functions with the standard ones")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code includes barrier() followed by writel(). writel() already has a
barrier on some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a barrier().
Since code already has an explicit barrier call, changing writel() to
writel_relaxed() and adding mmiowb() for ordering protection.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code includes wmb() followed by writel(). writel() already has a barrier on
some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a wmb().
Since code already has an explicit barrier call, changing writel() to
writel_relaxed().
Also add mmiowb() so that write code doesn't move outside of scope.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code includes wmb() followed by writel(). writel() already has a barrier on
some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a wmb().
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha