This dirver try to implement the Magic SysRq support[1] for
Amlogic Inc's meson platfo
>From the hardware perspective, the UART IP can't detect the 'BREAK' command
clearly via the status register. Instead, we rely on the combination of
'FRAME_ERR bit && ch == 0', and it works fine.
[1] Documentation/admin-guide/sysrq.rst
Signed-off-by: Yixun Lan <dlan@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sccnxp_probe() returns result of regulator_disable() that may lead
to returning zero, while device is not properly initialized.
Also the driver enables clocks, but it does not disable it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver register irq in .startup() and free the irq in
.shutdown(), then user will see the NULL interrupt output from
'cat /proc/interrupts' after the uart port test completed:
...
41: 515 0 0 0 GICv3 257 Level fsl-lpuart
42: 2 0 0 0 GICv3 258 Level
...
It is better to register all the irqs during probe function via devm_request_irq()
to avoid to call free_irq().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issue where unprintable characters can occur or output is cut off over
the serial uart / linux console depending on timing.
Problem occurs when changing the serial baud rate when setting up the
new console.The bcm63xx driver does a disable and flush of the uart tx
fifo while there is data still in the tx fifo.
If the tx fifo still has data it is trying to send out, we need to wait
until it is empty before disabling and flushing the uart.
When we now go to change the uart parameters including speed we check
if there is data currently in the tx fifo.If there is was mdelay(10)
and check again.If it tries 3 times and still has data in it we just
continue and sacrifice the tx fifo buffer.
A cleaner and more preferred approach would be to remove :
- spin_lock_irqsave()
- bcm_uart_disable()
- bcm_uart_flush()
However it is not clear if the author put those in to fix another
underlying issue.As a result this solution is a safer approach.
Output before the fix:
[0.306000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a° 0.315000] console[ttyS0] enabled
Output verified after the fix:
[0.315000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud = 1687500) is a bcm63xx_uart [0.334000] console[ttyS0] enabled
Signed-off-by: Russell Enderby <rte@gdn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul reported, that low rates like B300 make the driver to hang in
mxser_wait_until_sent. His debugging tackled the issue down to the
info->timeout computation in mxser_set_baud. Obviously, ints are used
there and they easily overflow with these low rates: B300 makes
info->timeout to be -373.
So switch all these types to unsigned as it ought to be. And use the u64
domain to perform the computation as in the worst case, we need 35 bits
to store the computed value (before division).
And use do_div not to break 32 bit kernels.
[v2] make it actually build
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Paul <Paul@abelian.netcom.co.uk>
Tested-by: <Paul@abelian.netcom.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Nothing really major this release, despite quite a lot of activity. Just lots of
things all over the place.
Some things of note include:
- Access via perf to a new type of PMU (IMC) on Power9, which can count both
core events as well as nest unit events (Memory controller etc).
- Optimisations to the radix MMU TLB flushing, mostly to avoid unnecessary Page
Walk Cache (PWC) flushes when the structure of the tree is not changing.
- Reworks/cleanups of do_page_fault() to modernise it and bring it closer to
other architectures where possible.
- Rework of our page table walking so that THP updates only need to send IPIs
to CPUs where the affected mm has run, rather than all CPUs.
- The size of our vmalloc area is increased to 56T on 64-bit hash MMU systems.
This avoids problems with the percpu allocator on systems with very sparse
NUMA layouts.
- STRICT_KERNEL_RWX support on PPC32.
- A new sched domain topology for Power9, to capture the fact that pairs of
cores may share an L2 cache.
- Power9 support for VAS, which is a new mechanism for accessing coprocessors,
and initial support for using it with the NX compression accelerator.
- Major work on the instruction emulation support, adding support for many new
instructions, and reworking it so it can be used to implement the emulation
needed to fixup alignment faults.
- Support for guests under PowerVM to use the Power9 XIVE interrupt controller.
And probably that many things again that are almost as interesting, but I had to
keep the list short. Plus the usual fixes and cleanups as always.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Andreas Schwab, Aneesh Kumar K.V, Anju
T Sudhakar, Arvind Yadav, Balbir Singh, Benjamin Herrenschmidt, Bhumika Goyal,
Breno Leitao, Bryant G. Ly, Christophe Leroy, Cédric Le Goater, Dan Carpenter,
Dou Liyang, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff Levand,
Hannes Reinecke, Haren Myneni, Ivan Mikhaylov, John Allen, Julia Lawall, LABBE
Corentin, Laurentiu Tudor, Madhavan Srinivasan, Markus Elfring, Masahiro
Yamada, Matt Brown, Michael Neuling, Murilo Opsfelder Araujo, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Rashmica
Gupta, Rob Herring, Rui Teng, Sam Bobroff, Santosh Sivaraj, Scott Wood,
Shilpasri G Bhat, Sukadev Bhattiprolu, Suraj Jitindar Singh, Tobin C. Harding,
Victor Aoqui.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UJtt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Nothing really major this release, despite quite a lot of activity.
Just lots of things all over the place.
Some things of note include:
- Access via perf to a new type of PMU (IMC) on Power9, which can
count both core events as well as nest unit events (Memory
controller etc).
- Optimisations to the radix MMU TLB flushing, mostly to avoid
unnecessary Page Walk Cache (PWC) flushes when the structure of the
tree is not changing.
- Reworks/cleanups of do_page_fault() to modernise it and bring it
closer to other architectures where possible.
- Rework of our page table walking so that THP updates only need to
send IPIs to CPUs where the affected mm has run, rather than all
CPUs.
- The size of our vmalloc area is increased to 56T on 64-bit hash MMU
systems. This avoids problems with the percpu allocator on systems
with very sparse NUMA layouts.
- STRICT_KERNEL_RWX support on PPC32.
- A new sched domain topology for Power9, to capture the fact that
pairs of cores may share an L2 cache.
- Power9 support for VAS, which is a new mechanism for accessing
coprocessors, and initial support for using it with the NX
compression accelerator.
- Major work on the instruction emulation support, adding support for
many new instructions, and reworking it so it can be used to
implement the emulation needed to fixup alignment faults.
- Support for guests under PowerVM to use the Power9 XIVE interrupt
controller.
And probably that many things again that are almost as interesting,
but I had to keep the list short. Plus the usual fixes and cleanups as
always.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Arvind Yadav, Balbir Singh,
Benjamin Herrenschmidt, Bhumika Goyal, Breno Leitao, Bryant G. Ly,
Christophe Leroy, Cédric Le Goater, Dan Carpenter, Dou Liyang,
Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff Levand, Hannes
Reinecke, Haren Myneni, Ivan Mikhaylov, John Allen, Julia Lawall,
LABBE Corentin, Laurentiu Tudor, Madhavan Srinivasan, Markus Elfring,
Masahiro Yamada, Matt Brown, Michael Neuling, Murilo Opsfelder Araujo,
Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Paul Mackerras, Rashmica Gupta, Rob Herring, Rui Teng, Sam Bobroff,
Santosh Sivaraj, Scott Wood, Shilpasri G Bhat, Sukadev Bhattiprolu,
Suraj Jitindar Singh, Tobin C. Harding, Victor Aoqui"
* tag 'powerpc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (321 commits)
powerpc/xive: Fix section __init warning
powerpc: Fix kernel crash in emulation of vector loads and stores
powerpc/xive: improve debugging macros
powerpc/xive: add XIVE Exploitation Mode to CAS
powerpc/xive: introduce H_INT_ESB hcall
powerpc/xive: add the HW IRQ number under xive_irq_data
powerpc/xive: introduce xive_esb_write()
powerpc/xive: rename xive_poke_esb() in xive_esb_read()
powerpc/xive: guest exploitation of the XIVE interrupt controller
powerpc/xive: introduce a common routine xive_queue_page_alloc()
powerpc/sstep: Avoid used uninitialized error
axonram: Return directly after a failed kzalloc() in axon_ram_probe()
axonram: Improve a size determination in axon_ram_probe()
axonram: Delete an error message for a failed memory allocation in axon_ram_probe()
powerpc/powernv/npu: Move tlb flush before launching ATSD
powerpc/macintosh: constify wf_sensor_ops structures
powerpc/iommu: Use permission-specific DEVICE_ATTR variants
powerpc/eeh: Delete an error out of memory message at init time
powerpc/mm: Use seq_putc() in two functions
macintosh: Convert to using %pOF instead of full_name
...
Here is the big staging and IIO driver update for 4.14-rc1.
Lots of staging driver fixes and cleanups, including some reorginizing
of the lustre header files to try to impose some sanity on what is, and
what is not, the uapi for that filesystem.
There are some tty core changes in here as well, as the speakup drivers
need them, and that's ok with me, they are sane and the speakup code is
getting nicer because of it.
There is also the addition of the obiligatory new wifi driver, just
because it has been a release or two since we added our last one...
Other than that, lots and lots of small coding style fixes, as usual.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa2AbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymboACfUsNhw+cJlVb25J70NULkye3y1PAAoJ+Ayq30
ckkLGakZayKcYEx50ffH
=KJwg
-----END PGP SIGNATURE-----
Merge tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the big staging and IIO driver update for 4.14-rc1.
Lots of staging driver fixes and cleanups, including some reorginizing
of the lustre header files to try to impose some sanity on what is,
and what is not, the uapi for that filesystem.
There are some tty core changes in here as well, as the speakup
drivers need them, and that's ok with me, they are sane and the
speakup code is getting nicer because of it.
There is also the addition of the obiligatory new wifi driver, just
because it has been a release or two since we added our last one...
Other than that, lots and lots of small coding style fixes, as usual.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (612 commits)
staging:rtl8188eu:core Fix remove unneccessary else block
staging: typec: fusb302: make structure fusb302_psy_desc static
staging: unisys: visorbus: make two functions static
staging: fsl-dpaa2/eth: fix off-by-one FD ctrl bitmaks
staging: r8822be: Simplify deinit_priv()
staging: r8822be: Remove some dead code
staging: vboxvideo: Use CONFIG_DRM_KMS_FB_HELPER to check for fbdefio availability
staging:rtl8188eu Fix comparison to NULL
staging: rts5208: rename mmc_ddr_tunning_rx_cmd to mmc_ddr_tuning_rx_cmd
Staging: Pi433: style fix - tabs and spaces
staging: pi433: fix spelling mistake: "preample" -> "preamble"
staging:rtl8188eu:core Fix Code Indent
staging: typec: fusb302: Export current-limit through a power_supply class dev
staging: typec: fusb302: Add support for USB2 charger detection through extcon
staging: typec: fusb302: Use client->irq as irq if set
staging: typec: fusb302: Get max snk mv/ma/mw from device-properties
staging: typec: fusb302: Set max supply voltage to 5V
staging: typec: tcpm: Add get_current_limit tcpc_dev callback
staging:rtl8188eu Use __func__ instead of function name
staging: lustre: coding style fixes found by checkpatch.pl
...
Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes, and
a new serial driver. Also in here are some much needed goldfish tty
driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWa2A+A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylNKACfWOuWb4PEGzPg2hF57V1g0cq8VXEAn0BtZT+n
uuCBV53ylesoHhEhKf/D
=g+za
-----END PGP SIGNATURE-----
Merge tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.14-rc1.
Well, not all that big, just a number of small serial driver fixes,
and a new serial driver. Also in here are some much needed goldfish
tty driver (emulator) fixes to try to get that codebase under control.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (94 commits)
tty: goldfish: Implement support for kernel 'earlycon' parameter
tty: goldfish: Use streaming DMA for r/w operations on Ranchu platforms
tty: goldfish: Refactor constants to better reflect their nature
serial: 8250_port: Remove useless NULL checks
earlycon: initialise baud field of earlycon device structure
tty: hvcs: make ktermios const
pty: show associative slave of ptmx in fdinfo
tty: n_gsm: Add compat_ioctl
tty: hvcs: constify vio_device_id
tty: hvc_vio: constify vio_device_id
tty: mips_ejtag_fdc: constify mips_cdmm_device_id
Introduce 8250_men_mcb
mcb: introduce mcb_get_resource()
serial: imx: Avoid post-PIO cleanup if TX DMA is started
tty: serial: imx: disable irq after suspend
serial: 8250_uniphier: add suspend/resume support
serial: 8250_uniphier: use CHAR register for canary to detect power-off
serial: 8250_uniphier: fix serial port index in private data
serial: 8250: of: Add new port type for MediaTek BTIF controller on MT7622/23 SoC
dt-bindings: serial: 8250: Add MediaTek BTIF controller bindings
...
Pull parisc updates from Helge Deller:
"Major changes include:
- Full support of the firmware Page Deallocation Table with
MADV_HWPOISON and MADV_SOFT_OFFLINE. A kernel thread scans
regularily for new bad memory pages.
- Full support for self-extracting kernel.
- Added UBSAN support.
- Lots of section mismatch fixes across all parisc drivers.
- Added examples for %pF and %pS usage in printk-formats.txt"
* 'parisc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (28 commits)
printk-formats.txt: Add examples for %pF and %pS usage
parisc: Fix up devices below a PCI-PCI MegaRAID controller bridge
parisc/core: Fix section mismatches
parisc/ipmi_si_intf: Fix section mismatches on parisc platform
parisc/input/hilkbd: Fix section mismatches
parisc/net/lasi_82596: Fix section mismatches
parisc/serio: Fix section mismatches in gscps2 and hp_sdc drivers
parisc: Fix section mismatches in parisc core drivers
parisc/parport_gsc: Fix section mismatches
parisc/scsi/lasi700: Fix section mismatches
parisc/scsi/zalon: Fix section mismatches
parisc/8250_gsc: Fix section mismatches
parisc/mux: Fix section mismatches
parisc/sticore: Fix section mismatches
parisc/harmony: Fix section mismatches
parisc: Wire up support for self-extracting kernel
parisc: Make existing core files reuseable for bootloader
parisc: Add core code for self-extracting kernel
parisc: Enable UBSAN support
parisc/random: Add machine specific randomness
...
Pull x86 asm updates from Ingo Molnar:
- Introduce the ORC unwinder, which can be enabled via
CONFIG_ORC_UNWINDER=y.
The ORC unwinder is a lightweight, Linux kernel specific debuginfo
implementation, which aims to be DWARF done right for unwinding.
Objtool is used to generate the ORC unwinder tables during build, so
the data format is flexible and kernel internal: there's no
dependency on debuginfo created by an external toolchain.
The ORC unwinder is almost two orders of magnitude faster than the
(out of tree) DWARF unwinder - which is important for perf call graph
profiling. It is also significantly simpler and is coded defensively:
there has not been a single ORC related kernel crash so far, even
with early versions. (knock on wood!)
But the main advantage is that enabling the ORC unwinder allows
CONFIG_FRAME_POINTERS to be turned off - which speeds up the kernel
measurably:
With frame pointers disabled, GCC does not have to add frame pointer
instrumentation code to every function in the kernel. The kernel's
.text size decreases by about 3.2%, resulting in better cache
utilization and fewer instructions executed, resulting in a broad
kernel-wide speedup. Average speedup of system calls should be
roughly in the 1-3% range - measurements by Mel Gorman [1] have shown
a speedup of 5-10% for some function execution intense workloads.
The main cost of the unwinder is that the unwinder data has to be
stored in RAM: the memory cost is 2-4MB of RAM, depending on kernel
config - which is a modest cost on modern x86 systems.
Given how young the ORC unwinder code is it's not enabled by default
- but given the performance advantages the plan is to eventually make
it the default unwinder on x86.
See Documentation/x86/orc-unwinder.txt for more details.
- Remove lguest support: its intended role was that of a temporary
proof of concept for virtualization, plus its removal will enable the
reduction (removal) of the paravirt API as well, so Rusty agreed to
its removal. (Juergen Gross)
- Clean up and fix FSGS related functionality (Andy Lutomirski)
- Clean up IO access APIs (Andy Shevchenko)
- Enhance the symbol namespace (Jiri Slaby)
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
objtool: Handle GCC stack pointer adjustment bug
x86/entry/64: Use ENTRY() instead of ALIGN+GLOBAL for stub32_clone()
x86/fpu/math-emu: Add ENDPROC to functions
x86/boot/64: Extract efi_pe_entry() from startup_64()
x86/boot/32: Extract efi_pe_entry() from startup_32()
x86/lguest: Remove lguest support
x86/paravirt/xen: Remove xen_patch()
objtool: Fix objtool fallthrough detection with function padding
x86/xen/64: Fix the reported SS and CS in SYSCALL
objtool: Track DRAP separately from callee-saved registers
objtool: Fix validate_branch() return codes
x86: Clarify/fix no-op barriers for text_poke_bp()
x86/switch_to/64: Rewrite FS/GS switching yet again to fix AMD CPUs
selftests/x86/fsgsbase: Test selectors 1, 2, and 3
x86/fsgsbase/64: Report FSBASE and GSBASE correctly in core dumps
x86/fsgsbase/64: Fully initialize FS and GS state in start_thread_common
x86/asm: Fix UNWIND_HINT_REGS macro for older binutils
x86/asm/32: Fix regs_get_register() on segment registers
x86/xen/64: Rearrange the SYSCALL entries
x86/asm/32: Remove a bunch of '& 0xffff' from pt_regs segment reads
...
Add early console functionality to the Goldfish tty driver.
When 'earlycon' kernel command line parameter is used with no options,
the early console is determined by the 'stdout-path' property in device
tree's 'chosen' node. This is illustrated in the following device tree
source example:
Device tree example:
chosen {
stdout-path = "/goldfish_tty@1f004000";
};
goldfish_tty@1f004000 {
interrupts = <0xc>;
reg = <0x1f004000 0x0 0x1000>;
compatible = "google,goldfish-tty";
};
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement tty r/w operations using streaming DMA.
Goldfish tty for Ranchu platforms has been modified to use
streaming DMA mappings for read/write operations. This change
eliminates the need for snooping through the TLB in QEMU using
cpu_get_phys_page_debug() which does not guarantee that it will
return the valid va -> pa mapping.
The streaming DMA mapping is implemented using dma_map_single() per
transfer, while dma_unmap_single() is used for unmapping right after
the DMA transfer.
Using DMA API is the proper way for handling r/w transfers and
makes this driver more portable, thus effectively eliminating
the need for virt_to_page() and page_to_phys() conversions.
This change does not affect the old style Goldfish tty behaviour
which is still used by the Goldfish emulator. Version register has
been added and probed to see which platform is running this driver.
Reading from the new register GOLDFISH_TTY_REG_VERSION using the
Goldfish emulator will return 0 and driver will work with virtual
addresses. Whereas if run on Ranchu it returns 1, and thus DMA is
used.
(Goldfish and Ranchu are code names for the first and the second
generation of virtual boards used by Android emulator.)
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Classify constants GOLDFISH_TTY_xxx into two groups: command ids and
register offsets. Apply different naming for register offsets (add
'REG_' after 'GOLDFISH_TTY_' in constant names). Change implementation
to use preprocessor's '#define' statements instead of 'enum'
declaration (as this is more common way of implementation in such
cases).
This makes the driver code easier to follow and hopefully prevents
future bugs.
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After switching to HR timers for RS485 the NULL checks for the object
inside timer functions become useless.
Remove them to avoid confusion to static analyzers.
Fixes 6e0a5de213 ("serial: 8250: Use hrtimers for rs485 delays")
Cc: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For now baud field of earlycon structure device is't initialised at all
in of_setup_earlycon (in oppositе to register_earlycon).
So when I use stdout-path to point earlycon device
(like stdout-path = &serial or stdout-path = "serial:115200n8")
baud field of earlycon device structure remains uninitialised and
earlycon initialization is not performed correctly as
of_setup_earlycon is used.
When pass all arguments via bootargs
(like bootargs = "earlycon=uart8250,mmio32,0xf0005000,115200n8")
initialization is performed correctly as register_earlycon is used.
So initialise baud field of earlycon device structure by value of
"current-speed" property from device tree or from options
(if they exist) when we use of_setup_earlycon
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make this const as it is not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty_alloc_driver() function never returns NULL, it returns error
pointers on error.
Fixes: ce808b7463 ("sparc64: vcc: TTY driver initialization and cleanup")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "tty-index" field to /proc/PID/fdinfo/N if N
specifies /dev/ptmx. The field shows the index of associative
slave pts.
Though a minor number is given for each pts instance, ptmx is not.
It means there is no way in user-space to know the association between
file descriptors for pts/n and ptmx. (n = 0, 1, ...)
This is different from pipe. About pipe such association can be solved
by inode of pipefs.
Providing the way to know the association between pts/n and ptmx helps
users understand the status of running system. lsof can utilize this field.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use this driver with 32 bit userspace applications on 64 bit
kernels a compat_ioctl is needed.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vio_device_id are not supposed to change at runtime. All functions
working with vio_device_id provided by <asm/vio.h> work with
const vio_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mips_cdmm_device_id are not supposed to change at runtime.
mips_cdmm_driver is working with const 'id_table'. So mark
the non-const mips_cdmm_device_id structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the 8250_men_mcb driver for the MEN 16Z125
IP-Core. This is a 16550-type UART with a 60 byte FIFO.
Due to strange old hardware, every board using this IP core requires
different values for uartclk. A reasonable default is included in
addition to the support of three boards. Additional values for other
boards will be added later.
This v2 has some whitespace fixes, I screwed this up yesterday.
Signed-off-by: Michael Moese <michael.moese@men.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx_transmit_buffer function should return if TX DMA has already
been started and not just skip over the buffer PIO write loop. (Which
did fix the initial problem, but could have unintentional side-effects)
Tested on an i.MX6Q board with half-duplex RS-485 and with RS-232.
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Uwe-Kleine König <u.kleine-koenig@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 514ab34dba ("serial: imx: Prevent TX buffer PIO write when a DMA has been started")
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any key on console is pressed when board is suspended,
board hangs.
Driver's interrupt handler must be guaranteed not to run while
resume/suspend_noirq() are being executed. See include/linux/pm.h
for details.
Tested on i.MX6 based board.
The idea of this fix is based on commit in official i.MX kernel tree:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git
commit 81e8e7d91d81 ("tty: serial: imx: disable irq after suspend")
Disable rx irq after suspend to avoid interrupt coming in early resume.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add suspend/resume support for UniPhier serial driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 core uses the SCR as a canary to discover if the console has
been powered-off.
This hardware does not have SCR at offset 7, but an unused register
CHAR at a different offset. As long as the character interrupt is
disabled, the register access has no impact, so it is useful as an
alternative scratch register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_register_8250_port() may allocate a different port index
than requested. The driver needs to remember the returned value of
serial8250_register_8250_port() for later use. Otherwise, the .remove
hook may unregister a different port.
Fixes: 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MediaTek BTIF controller is the serial interface similar to UART but it
works only as the digital device which is mainly used to communicate with
the connectivity module called CONNSYS inside the SoC which could be mostly
found on those MediaTek SoCs with Bluetooth feature such as MT7622 and
MT7623 SoCs.
And the controller is made as being compatible with the 8250 register
layout with extra registers such as DMA enablement so it tends to be
integrated with reusing 8250 OF driver. However, DMA mode is not being
supported yet in the current driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When moving earlycon early_param handling to serial, the devicetree
earlycons enable condition changed slightly.
We used to only do that for 'console'/'earlycon', but now would also
for 'console='/'earlycon='.
Fix it by using the same condition like before.
Fixes: d503187b6c (of/serial: move earlycon early_param handling to serial)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parisc_device_id are not supposed to change at runtime. All functions
working with parisc_device_id provided by <asm/parisc-device.h> work
with const parisc_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parisc_device_id are not supposed to change at runtime. All functions
working with parisc_device_id provided by <asm/parisc-device.h> work
with const parisc_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
66AK2G UART instances are not apart of the ALWAYS_ON power domain.
Therefore, pm_runtime calls must be made to properly insure the appropriate
power domains needed by UART are on. Keep legacy clk api calls since other
users of this driver may not support PM runtime.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use slightly more compact of_property_read_bool() calls for the boolean
properties instead of of_find_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the timers where based on the classic timers, giving a too
coarse resolution on systems with configs of less than 1000 HZ.
This patch changes the rs485 timers to hrtimers.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously the rs485 settings weren't considered when setting the RTS
line, so e.g. closing and reopening a port made serial_core to drive
the line as if rs485 was disabled.
This patch fixes those issues.
Signed-off-by: Rafael Gago Castano <rgc@hms.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use more compact of_property_read_bool() call for a boolean property
instead of of_find_property() call in sci_parse_dt().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It used to be a gap in port definitions after PORT_MAX_8250. Since the
new drivers are coming the gap become shorter and shorter until the
commit a2d6a987bf ("serial: 8250: Add new port type for TI DA8xx/66AK2x")
completely removed it.
So, while type here is just a formality, make things a little bit more
explicit for this driver and move port types to UAPI header. Note,
it uses two types for now.
Fixes: fddceb8b53 ("tty: 8250: Add 64byte UART support for FSL platforms")
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the request_irq() call to the end of the msm_startup(),
so that we don't handle interrupts while msm_startup() is
running. This avoids potential races while initialization
is in progress. For example, consider below scenario
where rx handler reads the intermediate value of dma->chan,
set in msm_request_rx_dma(), and tries to do dma mapping,
which results in data abort.
uart_port_startup()
msm_startup()
request_irq()
...
msm_request_rx_dma()
...
dma->chan = dma_request_slave_channel_reason(dev, "rx");
<UART RX IRQ>
msm_uart_irq()
msm_handle_rx_dm()
msm_start_rx_dma()
dma->desc = dma_map_single()
<data abort>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Reviewd-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to do a NULL check for debugfs_remove().
Quoting Documentation/filesystems/debugfs.txt:
"The dentry value can be NULL, in which case nothing will be removed."
, so remove the unneeded NULL check.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq() returns an error code, but the sprd_serial driver
ignores it and always returns -ENODEV. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Also, notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These uart_ops structures are only stored in the ops field of a
uart_port structure and this fields is const, so the uart_ops
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These vendor_data structures are only stored in the vendor field of
the uart_amba_port structure, as defined in the same file, and this
field is declared as const. Thus the vendor_data structures can be
const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have tty_kopen, we no longer need to export tty_open_by_driver.
This patch makes this function static.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 12e84c71b7 ("tty: export tty_open_by_driver") exports
tty_open_by_device to allow tty to be opened from inside kernel which
works fine except that it doesn't handle contention with user space or
another kernel-space open of the same tty. For example, opening a tty
from user space while it is kernel opened results in failure and a
kernel log message about mismatch between tty->count and tty's file
open count.
This patch makes kernel access to tty exclusive, so that if a user
process or kernel opens a kernel opened tty, it gets -EBUSY. It does
this by adding TTY_KOPENED flag to tty->flags. When this flag is set,
tty_open_by_driver returns -EBUSY. Instead of overloading
tty_open_by_driver for both kernel and user space, this
patch creates a separate function tty_kopen which closely follows
tty_open_by_driver. tty_kclose closes the tty opened by tty_kopen.
To address the mismatch between tty->count and #fd's, this patch adds
#kopen's to the count before comparing it with tty->count. That way
check_tty_count reflects correct usage count.
Returning -EBUSY on tty open is a change in the interface. I have
tested this with minicom, picocom and commands like "echo foo >
/dev/ttyS0". They all correctly report "Device or resource busy" when
the tty is already kernel opened.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implementation of TIOCGPTPEER has two issues.
When /dev/ptmx (as opposed to /dev/pts/ptmx) is opened the wrong
vfsmount is passed to dentry_open. Which results in the kernel displaying
the wrong pathname for the peer.
The second is simply by caching the vfsmount and dentry of the peer it leaves
them open, in a way they were not previously Which because of the inreased
reference counts can cause unnecessary behaviour differences resulting in
regressions.
To fix these move the ioctl into tty_io.c at a generic level allowing
the ioctl to have access to the struct file on which the ioctl is
being called. This allows the path of the slave to be derived when
opening the slave through TIOCGPTPEER instead of requiring the path to
the slave be cached. Thus removing the need for caching the path.
A new function devpts_ptmx_path is factored out of devpts_acquire and
used to implement a function devpts_mntget. The new function devpts_mntget
takes a filp to perform the lookup on and fsi so that it can confirm
that the superblock that is found by devpts_ptmx_path is the proper superblock.
v2: Lots of fixes to make the code actually work
v3: Suggestions by Linus
- Removed the unnecessary initialization of filp in ptm_open_peer
- Simplified devpts_ptmx_path as gotos are no longer required
[ This is the fix for the issue that was reverted in commit
143c97cc65, but this time without breaking 'pbuilder' due to
increased reference counts - Linus ]
Fixes: 54ebbfb160 ("tty: add TIOCGPTPEER ioctl")
Reported-by: Christian Brauner <christian.brauner@canonical.com>
Reported-and-tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lguest seems to be rather unused these days. It has seen only patches
ensuring it still builds the last two years and its official state is
"Odd Fixes".
Remove it in order to be able to clean up the paravirt code.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lguest@lists.ozlabs.org
Cc: rusty@rustcorp.com.au
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20170816173157.8633-3-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This reverts commit c8c03f1858.
It turns out that while fixing the ptmx file descriptor to have the
correct 'struct path' to the associated slave pty is a really good
thing, it breaks some user space tools for a very annoying reason.
The problem is that /dev/ptmx and its associated slave pty (/dev/pts/X)
are on different mounts. That was what caused us to have the wrong path
in the first place (we would mix up the vfsmount of the 'ptmx' node,
with the dentry of the pty slave node), but it also means that now while
we use the right vfsmount, having the pty master open also keeps the pts
mount busy.
And it turn sout that that makes 'pbuilder' very unhappy, as noted by
Stefan Lippers-Hollmann:
"This patch introduces a regression for me when using pbuilder
0.228.7[2] (a helper to build Debian packages in a chroot and to
create and update its chroots) when trying to umount /dev/ptmx (inside
the chroot) on Debian/ unstable (full log and pbuilder configuration
file[3] attached).
[...]
Setting up build-essential (12.3) ...
Processing triggers for libc-bin (2.24-15) ...
I: unmounting dev/ptmx filesystem
W: Could not unmount dev/ptmx: umount: /var/cache/pbuilder/build/1340/dev/ptmx: target is busy
(In some cases useful info about processes that
use the device is found by lsof(8) or fuser(1).)"
apparently pbuilder tries to unmount the /dev/pts filesystem while still
holding at least one master node open, which is arguably not very nice,
but we don't break user space even when fixing other bugs.
So this commit has to be reverted.
I'll try to figure out a way to avoid caching the path to the slave pty
in the master pty. The only thing that actually wants that slave pty
path is the "TIOCGPTPEER" ioctl, and I think we could just recreate the
path at that time.
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Eric W Biederman <ebiederm@xmission.com>
Cc: Christian Brauner <christian.brauner@canonical.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian Brauner reported that if you use the TIOCGPTPEER ioctl() to
get a slave pty file descriptor, the resulting file descriptor doesn't
look right in /proc/<pid>/fd/<fd>. In particular, he wanted to use
readlink() on /proc/self/fd/<fd> to get the pathname of the slave pty
(basically implementing "ptsname{_r}()").
The reason for that was that we had generated the wrong 'struct path'
when we create the pty in ptmx_open().
In particular, the dentry was correct, but the vfsmount pointed to the
mount of the ptmx node. That _can_ be correct - in case you use
"/dev/pts/ptmx" to open the master - but usually is not. The normal
case is to use /dev/ptmx, which then looks up the pts/ directory, and
then the vfsmount of the ptmx node is obviously the /dev directory, not
the /dev/pts/ directory.
We actually did have the right vfsmount available, but in the wrong
place (it gets looked up in 'devpts_acquire()' when we get a reference
to the pts filesystem), and so ptmx_open() used the wrong mnt pointer.
The end result of this confusion was that the pty worked fine, but when
if you did TIOCGPTPEER to get the slave side of the pty, end end result
would also work, but have that dodgy 'struct path'.
And then when doing "d_path()" on to get the pathname, the vfsmount
would not match the root of the pts directory, and d_path() would return
an empty pathname thinking that the entry had escaped a bind mount into
another mount.
This fixes the problem by making devpts_acquire() return the vfsmount
for the pts filesystem, allowing ptmx_open() to trivially just use the
right mount for the pts dentry, and create the proper 'struct path'.
Reported-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add handlers to support TTY install & cleanup operations
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handler to support TTY break_ctl operation
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handler to support TTY chars_in_buffer operation
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handlers to support TTY write & write_room operations
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handler to support TTY hangup operation
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handlers to support TTY open & close operations
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable event processing engine to handle LDC events
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RX & TX timers to perform delayed/asynchronous LDC
read and write operations.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create sysfs attribute group to show the domain name and
send break command.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables VCC port probe and removal to initialize and terminate
VCC ports respectively. When a device/port matching the VCC driver
is added, the probe function is invoked along with a reference
to the device. remove function is called when the device is
removed.
Also add APIs to cache and retrieve VCC ports from a VCC table
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and register TTY driver during module init. Cleanup
TTY driver during module exit.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add C macros to print debug messages from VCC module
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enables the Virtual Console Concentrator (VCC) module
in linux kernel
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two tty serial driver fixes for 4.13-rc5. One is a revert of a
-rc1 patch that turned out to not be a good idea, and the other is a fix
for the pl011 serial driver.
Both have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWY+1vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykreACeLI2spfagnOcnW264PGHxLMgj47EAn0JPSNIg
5FLEtVsgxMuc8kc4LkDb
=58g+
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
Sergey noticed a small but fatal mistake in __tty_insert_flip_char,
leading to an oops in an interrupt handler when using any serial
port.
The problem is that I accidentally took the tty_buffer pointer
before calling __tty_buffer_request_room(), which replaces the
buffer. This moves the pointer lookup to the right place after
allocating the new buffer space.
Fixes: 979990c628 ("tty: improve tty_insert_flip_char() fast path")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1104321a7b.
The code is not dead at all and breaks winbond-cir.
Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
00:03: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a CIR port
lirc lirc0: lirc_dev: driver ir-lirc-codec (winbond-cir) registered at minor = 0
winbond-cir 00:03: Region 0x2f8-0x2ff already in use!
winbond-cir: probe of 00:03 failed with error -16
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device-specific property should be prefixed with the vendor name,
not "linux,", as Linus Walleij pointed out. Change this and document the
bindings of this platform device.
We didn't ship the old binding in a release yet. So we can still change
it without breaking an official API.
Fixes: 380b1e2f3a ("gpio-exar/8250-exar: Make set of exported GPIOs configurable")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For debugging very early boot problems we have CONFIG_PPC_EARLY_DEBUG,
which allows configuring the kernel such that it unconditionally writes
to a particular type of console, regardless of whether that console
exists or not. This is useful sometimes when the kernel crashes before
it can even determine what platform it's on, and therefore what consoles
exist.
However if you boot a kernel built this way on a different platform, it
will generally crash because it writes to a console that doesn't exist.
A particularly nasty instance of this is if you enable the hypervisor
console early debug, and then boot that kernel on bare metal. The result
is that the kernel calls "the hypervisor" very early in boot, but the
kernel *is* the hypervisor, so we jump to the system call handler and
start executing all sorts of code that isn't ready to be run. This may
lead to a machine check or check stop depending on how lucky you are.
Luckily there is an easy way to avoid this particular case. We simply
read the MSR before installing the hooks, and if we see MSR_HV is set
then we are the hypervisor and we definitely should not use the
hypervisor console.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The work-around for Qualcomm Technologies QDF2400 Erratum 44 hinges on a
global variable defined in the pl011 driver. The ACPI SPCR parsing code
determines whether the work-around is needed, and if so, it changes the
console name from "pl011" to "qdf2400_e44". The expectation is that
the pl011 driver will implement the work-around when it sees the console
name. The global variable qdf2400_e44_present is set when that happens.
The problem is that work-around needs to be enabled when the pl011
driver probes, not when the console name is queried. However, sbsa_probe()
is called before pl011_console_match(). The work-around appeared to work
previously because the default console on QDF2400 platforms was always
ttyAMA1. The first time sbsa_probe() is called (for ttyAMA0),
qdf2400_e44_present is still false. Then pl011_console_match() is called,
and it sets qdf2400_e44_present to true. All subsequent calls to
sbsa_probe() enable the work-around.
The solution is to move the global variable into spcr.c and let the
pl011 driver query it during probe time. This works because all QDF2400
platforms require SPCR, so parse_spcr() will always be called.
pl011_console_match still checks for the "qdf2400_e44" console name,
but it doesn't do anything else special.
Fixes: 5a0722b898 ("tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44")
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While working on improving the fast path of tty_insert_flip_char(),
I noticed that by calling tty_buffer_request_room(), we needlessly
move to the separate flag buffer mode for the tty, even when all
characters use TTY_NORMAL as the flag.
This changes the code to call __tty_buffer_request_room() with the
correct flag, which will then allocate a regular buffer when it rounds
out of space but no special flags have been used. I'm guessing that
this is the behavior that Peter Hurley intended when he introduced
the compacted flip buffers.
Fixes: acc0f67f30 ("tty: Halve flip buffer GFP_ATOMIC memory consumption")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernelci.org reports a crazy stack usage for the VT code when CONFIG_KASAN
is enabled:
drivers/tty/vt/keyboard.c: In function 'kbd_keycode':
drivers/tty/vt/keyboard.c:1452:1: error: the frame size of 2240 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The problem is that tty_insert_flip_char() gets inlined many times into
kbd_keycode(), and also into other functions, and each copy requires 128
bytes for stack redzone to check for a possible out-of-bounds access on
the 'ch' and 'flags' arguments that are passed into
tty_insert_flip_string_flags as a variable-length string.
This introduces a new __tty_insert_flip_char() function for the slow
path, which receives the two arguments by value. This completely avoids
the problem and the stack usage goes back down to around 100 bytes.
Without KASAN, this is also slightly better, as we don't have to
spill the arguments to the stack but can simply pass 'ch' and 'flag'
in registers, saving a few bytes in .text for each call site.
This should be backported to linux-4.0 or later, which first introduced
the stack sanitizer in the kernel.
Cc: stable@vger.kernel.org
Fixes: c420f167db ("kasan: enable stack instrumentation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct serial_rs485 parameter is both input and output and is
supposed to hold the actually used configuration on return. So clear
unsupported settings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the board we are guessing has been listed in black list we don't need
to enable it twice. The associated driver, if any, will take care about
proper initialization.
To achieve this we split out two helper functions, i.e.
serial_pci_is_class_communication() and serial_pci_is_blacklisted() which will
be called before pcim_enable_device(). We can do this since PCI specification
requires class, device and vendor ID registers to be always present in the
configuration space.
As an example what happens before this patch applied
(These are some debug prints, don't search for them in kernel sources):
serial 0000:00:04.1: Mapped GSI28 to IRQ28
serial 0000:00:04.2: Mapped GSI29 to IRQ29
serial 0000:00:04.3: Mapped GSI54 to IRQ54
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54
After we will have just last three lines out of above.
8250_mid 0000:00:04.1: Mapped GSI28 to IRQ28
8250_mid 0000:00:04.2: Mapped GSI29 to IRQ29
8250_mid 0000:00:04.3: Mapped GSI54 to IRQ54
While here, correct a value of error code mentioned in the comment of
serial_pci_guess_board().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First 16 bits in the flags field are user-visible except
UPF_NO_TXEN_TEST. To keep it clean we introduce internal quirks and move
UPF_NO_TXEN_TEST to them. Rename the constant to UPQ_NO_TXEN_TEST to
distinguish with port flags. Users are converted accordingly.
The quirks field might be extended later to hold the additional ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
upf_t is a bitwise defined type and any assignment from different, but
compatible, types makes static analyzer unhappy.
drivers/tty/serial/serial_core.c:793:29: warning: incorrect type in assignment (different base types)
drivers/tty/serial/serial_core.c:793:29: expected int [signed] flags
drivers/tty/serial/serial_core.c:793:29: got restricted upf_t [usertype] flags
drivers/tty/serial/serial_core.c:867:19: warning: incorrect type in assignment (different base types)
drivers/tty/serial/serial_core.c:867:19: expected restricted upf_t [usertype] new_flags
drivers/tty/serial/serial_core.c:867:19: got int [signed] flags
Enforce corresponding types when upf_t being assigned.
Note, we need __force attribute due to the scope of variable. It's being
used in user space with plain old type while kernel uses bitwise one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlycon would be alive outside the init code in these cases:
1/ we have keep_bootcon in cmdline.
2/ we don't have a real console to switch to.
So remove the __init marking to avoid invalid memory access.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several error handling paths in aspeed_vuart_probe(),
where sysfs group is left unremoved. The patch fixes them.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Spreadtrum's serial device, nearly all of interrupts would be cleared
by hardware except timeout interrupt. This patch removed the operation
of clearing all interrupt in irq handler, instead added an if statement
to check if the timeout interrupt is supposed to be cleared.
Wrongly clearing timeout interrupt would lead to uart data stay in rx
fifo, that means the driver cannot read them out anymore.
Signed-off-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait queue was only initialized and then checked if it contains
active jobs but a job is never added. The last real user was removed
with commit 9d297239b8 ("serial: imx-serial - update UART IMX driver
to use cyclic DMA").
Further there is no need to release the lock for the check if the port
should be woken up, (and IMHO there never was) so drop the unlock/lock
pair in dma_tx_callback(), too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare(info->clk) is missed in of_platform_serial_probe(),
while irq_dispose_mapping(port->irq) is missed in of_platform_serial_setup().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-serial@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2442 1088 8 3538 dd2 tty/serial/jsm/jsm_driver.o
File size After adding 'const':
text data bss dec hex filename
3082 448 8 3538 dd2 tty/serial/jsm/jsm_driver.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
41180 480 185 41845 a375 drivers/tty/synclink_gt.o
File size After adding 'const':
text data bss dec hex filename
41340 320 185 41845 a375 drivers/tty/synclink_gt.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12626 18128 0 30754 7822 tty/serial/8250/8250_pci.o
File size After adding 'const':
text data bss dec hex filename
23986 6768 0 30754 7822 tty/serial/8250/8250_pci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
4030 1280 0 5310 14be tty/serial/8250/8250_exar.o
File size After adding 'const':
text data bss dec hex filename
4958 352 0 5310 14be tty/serial/8250/8250_exar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
14201 656 1760 16617 40e9 drivers/tty/moxa.o
File size After adding 'const':
text data bss dec hex filename
14329 528 1760 16617 40e9 drivers/tty/moxa.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
51755 400 513 52668 cdbc drivers/tty/synclink.o
File size After adding 'const':
text data bss dec hex filename
51883 304 513 52700 cddc drivers/tty/synclink.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
20253 1184 19904 41341 a17d drivers/tty/mxser.o
File size After adding 'const':
text data bss dec hex filename
21117 300 19904 41341 a17d drivers/tty/mxser.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12176 1520 25864 39560 9a88 drivers/tty/isicom.o
File size After adding 'const':
text data bss dec hex filename
12528 1168 25864 39560 9a88 drivers/tty/isicom.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
44660 432 104 45196 b08c drivers/tty/synclinkmp.o
File size After adding 'const':
text data bss dec hex filename
44756 336 104 45196 b08c drivers/tty/synclinkmp.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds fifo mode support for rx and tx.
A fifo configuration is set in each port structure.
Add has_fifo flag to usart configuration to use fifo only when possible.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for wake-up from low power modes. This extends stm32f7.
Introduce new compatible for stm32h7 to manage wake-up capability.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement support of RTS in USART control register
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase max number of ports for stm32h7
which supports up to 8 uart and usart instances.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct management of multi-ports. Each port has
its own last residue value and its own alias.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This mirrors commit 2a41bc2a2b but for 32-bit register definitions.
Fix a minor typo while at it.
Signed-off-by: Marius Vlad <marius.vlad0@gmail.com>
CC: Nicolae Rosia <nicolae_rosia@mentor.com>
CC: Stefan Golinschi <stefan.golinschi@gmail.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement serial console driver to complement earlycon.
Based on LeMaker linux-actions tree.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCGPTPEER is only used for unix98 PTYs, and we get a warning
when those are disabled:
drivers/tty/pty.c:466:12: error: 'pty_get_peer' defined but not used [-Werror=unused-function]
This moves the respective functions inside of the existing #ifdef.
Fixes: 54ebbfb160 ("tty: add TIOCGPTPEER ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Aleksa Sarai <asarai@suse.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0d6fce9044 ("tty: serial: lpuart: introduce lpuart_soc_data to
represent SoC property") introduced a buggy logic for detecting the 32-bit
type UART since the condition: "if (sport->port.iotype & UPIO_MEM32BE)"
is always true.
Performing such bitfield AND operation is not correct, because in the
case of Vybrid UART iotype is UPIO_MEM (2), so:
UPIO_MEM & UPIO_MEM32BE = 010 & 110 = 010, which is true.
Such logic tells the driver to always treat the UART operations as 32-bit,
leading to the driver misbehavior on Vybrid.
Fix the 32-bit type detection logic to avoid UART breakage on Vybrid.
While at it, introduce a lpuart_is_32() function to help readability.
Fixes: 0d6fce9044 ("tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property")
Reported-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function imx_transmit_buffer starts a TX DMA if DMA is enabled, since
commit 91a1a909f9 ("serial: imx: Support sw flow control in DMA mode").
It also carries on and attempts to write the same TX buffer using PIO.
This results in TX data corruption and double-incrementing xmit->tail
with the knock-on effect of tail passing head and a page of garbage
being sent out.
This seems to be triggered mostly when using RS485 half duplex on SMP
systems, but is probably not limited to just those.
Tested locally on an i.MX6Q with an RS485 half duplex transceiver on
UART3, and also by Clemens Gruber.
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Ian Jamison <ian.dev@arkver.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a3015affdf as there
are complaints that it is incorrect.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nandor Han <nandor.han@ge.com>
Cc: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
The kstrtol() function returns -ERANGE as well as -EINVAL so these tests
are not enough. It's not a super serious bug, but my static checker
correctly complains that the "r" variable might be used uninitialized.
Fixes: 5d23188a47 ("serial: sh-sci: make RX FIFO parameters tunable via sysfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like we intended to return an error code here, because we
dereference "ascport->pinctrl" on the next lines.
Fixes: 6929cb00a5 ("serial: st-asc: Read in all Pinctrl states")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code like the rest of the kernel.
Link: http://lkml.kernel.org/r/55d3e89d50bb03d603bfb28019fab07f48bdc714.1499284835.git.joe@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO line
may loose its state during suspend/resume of the system to save
power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes.
-----BEGIN PGP SIGNATURE-----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=TpW1
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing huge,
just lots of development by a number of different developers, full
details in the shortlog.
All of these have been in linux-next for a while. There will be a merge
issue with the arm-soc tree in the include/linux/platform_data/atmel.h
file. Stephen has sent out a fixup for it, so it shouldn't be that
difficult to merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpZ9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylkTgCfV2HhbxIph/aEL1nJmwW64oCXFrMAoK59ZH65
tBZIosv0d91K1A+mObBT
=adPL
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large tty/serial patchset for 4.13-rc1.
A lot of tty and serial driver updates are in here, along with some
fixups for some __get/put_user usages that were reported. Nothing
huge, just lots of development by a number of different developers,
full details in the shortlog.
All of these have been in linux-next for a while"
* tag 'tty-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty: serial: lpuart: add a more accurate baud rate calculation method
tty: serial: lpuart: add earlycon support for imx7ulp
tty: serial: lpuart: add imx7ulp support
dt-bindings: serial: fsl-lpuart: add i.MX7ULP support
tty: serial: lpuart: add little endian 32 bit register support
tty: serial: lpuart: refactor lpuart32_{read|write} prototype
tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property
serial: imx-serial - move DMA buffer configuration to DT
serial: imx: Enable RTSD only when needed
serial: imx: Remove unused members from imx_port struct
serial: 8250: 8250_omap: Fix race b/w dma completion and RX timeout
serial: 8250: Fix THRE flag usage for CAP_MINI
tty/serial: meson_uart: update to stable bindings
dt-bindings: serial: Add bindings for the Amlogic Meson UARTs
serial: Delete dead code for CIR serial ports
serial: sirf: make of_device_ids const
serial/mpsc: switch to dma_alloc_attrs
tty: serial: Add Actions Semi Owl UART earlycon
dt-bindings: serial: Document Actions Semi Owl UARTs
tty/serial: atmel: make the driver DT only
...
Here's the large set of staging and iio driver patches for 4.13-rc1.
After over 500 patches, we removed about 200 more lines of code than we
added, not great, but we added some new IIO drivers for unsupported
hardware, so it's an overall win.
Also here are lots of small fixes, and some tty core api additions (with
the tty maintainer's ack) for the speakup drivers, those are finally
getting some much needed cleanups and are looking much better now than
before. Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpY5g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykmRACfQOTfUq+BhL9Aw6UnZxI/cxnU1IgAnj51Nx2X
WH4LqHdq2xo4YKOzzVVX
=bDdB
-----END PGP SIGNATURE-----
Merge tag 'staging-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here's the large set of staging and iio driver patches for 4.13-rc1.
After over 500 patches, we removed about 200 more lines of code than
we added, not great, but we added some new IIO drivers for unsupported
hardware, so it's an overall win.
Also here are lots of small fixes, and some tty core api additions
(with the tty maintainer's ack) for the speakup drivers, those are
finally getting some much needed cleanups and are looking much better
now than before. Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (529 commits)
staging: lustre: replace kmalloc with kmalloc_array
Staging: ion: fix code style warning from NULL comparisons
staging: fsl-mc: make dprc.h header private
staging: fsl-mc: move mc-cmd.h contents in the public header
staging: fsl-mc: move mc-sys.h contents in the public header
staging: fsl-mc: fix a few implicit includes
staging: fsl-mc: remove dpmng API files
staging: fsl-mc: move rest of mc-bus.h to private header
staging: fsl-mc: move couple of definitions to public header
staging: fsl-mc: move irq domain creation prototype to public header
staging: fsl-mc: turn several exported functions static
staging: fsl-mc: delete prototype of unimplemented function
staging: fsl-mc: delete duplicated function prototypes
staging: fsl-mc: decouple the mc-bus public headers from dprc.h
staging: fsl-mc: drop useless #includes
staging: fsl-mc: be consistent when checking strcmp() return
staging: fsl-mc: move comparison before strcmp() call
staging: speakup: make function ser_to_dev static
staging: ks7010: fix spelling mistake: "errror" -> "error"
staging: rtl8192e: fix spelling mistake: "respose" -> "response"
...
Pull s390 updates from Martin Schwidefsky:
"The bulk of the s390 patches for 4.13. Some new things but mostly bug
fixes and cleanups. Noteworthy changes:
- The SCM block driver is converted to blk-mq
- Switch s390 to 5 level page tables. The virtual address space for a
user space process can now have up to 16EB-4KB.
- Introduce a ELF phdr flag for qemu to avoid the global
vm.alloc_pgste which forces all processes to large page tables
- A couple of PCI improvements to improve error recovery
- Included is the merge of the base support for proper machine checks
for KVM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
s390/dasd: Fix faulty ENODEV for RO sysfs attribute
s390/pci: recognize name clashes with uids
s390/pci: provide more debug information
s390/pci: fix handling of PEC 306
s390/pci: improve pci hotplug
s390/pci: introduce clp_get_state
s390/pci: improve error handling during fmb (de)registration
s390/pci: improve unreg_ioat error handling
s390/pci: improve error handling during interrupt deregistration
s390/pci: don't cleanup in arch_setup_msi_irqs
KVM: s390: Backup the guest's machine check info
s390/nmi: s390: New low level handling for machine check happening in guest
s390/fpu: export save_fpu_regs for all configs
s390/kvm: avoid global config of vm.alloc_pgste=1
s390: rename struct psw_bits members
s390: rename psw_bits enums
s390/mm: use correct address space when enabling DAT
s390/cio: introduce io_subchannel_type
s390/ipl: revert Load Normal semantics for LPAR CCW-type re-IPL
s390/dumpstack: remove raw stack dump
...
This implements the setup of RS232 and the switch-over to RS485 or RS422
for the Siemens IOT2040. That uses an EXAR XR17V352 with external logic
to switch between the different modes. The external logic is controlled
via MPIO pins of the EXAR controller.
Only pin 10 can be exported as GPIO on the IOT2040. It is connected to
an LED.
As the XR17V352 used on the IOT2040 is not equipped with an external
EEPROM, it cannot present itself as IOT2040-variant via subvendor/
subdevice IDs. Thus, we have to check via DMI for the target platform.
Co-developed with Sascha Weisenberger.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the SIMATIC, IOT2040 only a single pin is exportable as GPIO, the
rest is required to operate the UART. To allow modeling this case,
expand the platform device data structure to specify a (consecutive) pin
subset for exporting by the gpio-exar driver.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This prepares the addition of IOT2040 platform support by preparing the
needed setup and rs485_config hooks.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the parent of the exar gpiochip to its platform device, like other
gpiochips are doing it. In order to keep the relationship discoverable
for ACPI systems, set the platform device companion to the PCI device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commtech adapters need the MPIOs for internal purposes, and the
gpio-exar driver already refused to pick them up. But there is actually
no point in even creating the underlying platform device.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On new LPUART versions, the oversampling ratio for the receiver can be
changed from 4x (00011) to 32x (11111) which could help us get a more
accurate baud rate divider.
The idea is to use the best OSR (over-sampling rate) possible.
Note, OSR is typically hard-set to 16 in other LPUART instantiations.
Loop to find the best OSR value possible, one that generates minimum
baud diff iterate through the rest of the supported values of OSR.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon is executed quite early before the device tree probe,
so we need correctly initialize the port membase and iotype for
imx7ulp during early console setup before using.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx7ulp is basically the same as ls1021a. It's also
32 bit width register, but unlike ls1021a, it's little endian.
Besides that, imx7ulp lpuart has a minor different register layout
from ls1021a that it has four extra registers (verid, param, global,
pincfg) located at the beginning of register map, which are currently
not used by the driver and less to be used later.
To ease the register difference handling, we add a reg_off member
in lpuart_soc_data structure to represent if the normal
lpuart32_{read|write} requires plus a offset to hide the issue.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use standard port->iotype to distinguish endian difference. Note as we
read/write register by checking iotype dynamically, we need to initialize
the iotype correctly for earlycon as well to avoid a break.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com> (supporter:TTY LAYER)
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
ChangeLog:
v3->v4:
* Removed unneeded semicolon catched by 0day Robot.
v2->v3:
* Instead of using global var, use standard port->iotype to distinguish
endian difference.
v1->v2:
* No changes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the original lpuart32_read/write takes no port specific
information arguments, it's hard to distinguish port difference
within the API. Although it works before, but not suitable anymore
when adding more new chips support.
So let's convert it to accept a new struct uart_port argument
to make it be able to retrieve more port specific information.
This is a preparation for the later adding new chips support
more easily. No functions changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is used to dynamically check the SoC specific lpuart properies.
Currently only the iotype is added, it functions the same as before.
With this, new chips with different iotype will be more easily added.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the DMA buffer can affect the delta time between data being
produced and data being consumed. Basically the DMA system will move
data to tty buffer when a) DMA buffer is full b) serial line is idle.
The situation is visible when producer generates data continuously and
there is no possibility for idle line. At this point the DMA buffer is
directly affecting the delta time.
The patch will add the possibility to configure the DMA buffers in DT,
which case by case can be configured separately for every driver
instance. The DT configuration is optional and in case missing the
driver will use the 4096 buffer with 4 periods (as before), therefore no
clients are impacted by this change.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, this IRQ is always enabled. Some devices might mux these pins
to other I/Os, like I2C. This could lead to spurious interrupts.
This commit makes this IRQ optional, by using the field have_rtscts.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IRDA support is gone since commit afe9cbb1a6 ("serial: imx: drop
support for IRDA"), so remove the remaining irda members from
imx_port structure.
While at it, also remove 'trcv_delay' which is also unused.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA RX completion handler for UART is called from a tasklet and hence
may be delayed depending on the system load. In meanwhile, there may be
RX timeout interrupt which can get serviced first before DMA RX
completion handler is executed for the completed transfer.
omap_8250_rx_dma_flush() which is called on RX timeout interrupt makes
sure that the DMA RX buffer is pushed and then the FIFO is drained and
also queues a new DMA request. But, when DMA RX completion handler
executes, it will erroneously flush the currently queued DMA transfer
which sometimes results in data corruption and double queueing of DMA RX
requests.
Fix this by checking whether RX completion is for the currently queued
transfer or not. And also hold port lock when in DMA completion to avoid
race wrt RX timeout handler preempting it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BCM2835 MINI UART has non-standard THRE semantics. Conventionally
the bit means that the FIFO is empty (although there may still be a
byte in the transmit register), but on 2835 it indicates that the FIFO
is not full. This causes interrupts after every byte is transmitted,
with the FIFO providing some interrupt latency tolerance.
A consequence of this difference is that the usual strategy of writing
multiple bytes into the TX FIFO after checking THRE once is unsafe.
In the worst case of 7 bytes in the FIFO, writing 8 bytes loses all
but the first since by then the FIFO is full.
There is an HFIFO ("Hidden FIFO") capability that causes the transmit
loop to terminate when both THRE and TEMT are set, i.e. when the TX
block is completely idle. This is unnecessarily cautious, potentially
causing gaps in transmission.
Add a new conditional to the transmit loop, predicated on CAP_MINI,
that exits when THRE is no longer set (the FIFO is full). This allows
the FIFO to fill quickly but subsequent writes are paced by the
transmission rate.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function converts strings like ttyS0 and ttyUSB0 to dev_t like
(4, 64) and (188, 0). It does this by scanning tty_drivers list for
corresponding device name and index. If the driver is not registered,
this function returns -ENODEV. It also acquires tty_mutex.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes reloading of the GPIO driver for the same platform device
instance as created by the exar UART driver: First of all, the driver
sets drvdata to its own value during probing and does not restore the
original value on exit. But this won't help anyway as the core clears
drvdata after the driver left.
Set the platform device parent instead.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch handle the stable UART bindings but also keeps compatibility
with the legacy non-stable bindings until all boards uses them.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e4fda3a042 ("serial: don't register CIR serial ports") adds a
check for PORT_8250_CIR to serial8250_register_8250_port(). But the code
isn't needed as the function never takes the branch when the port is CIR
serial port.
This patch deletes the dead code.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dma_alloc_attrs directly instead of the dma_alloc_noncoherent wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This implements an earlycon for Actions Semi S500/S900 SoCs.
Based on LeMaker linux-actions tree.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that AVR32 is gone, platform_data are not used to initialize the driver
anymore, remove that path from the driver. Also remove the now unused
struct atmel_uart_data.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_default_console_device was only used by AVR32, in particular
arch/avr32/mach-at32ap/at32ap700x.c which is now gone. Remove it from the
driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting an alt_speed using the ROCKET_SPD flags has been deprecated
since v2.1.69, and has been broken since commit 6865ff222c ("TTY: do
not warn about setting speed via SPD_*") without anyone noticing.
To make things worse commit 6df3526b66 ("rocket: first pass at termios
reporting") in v2.6.25 started reporting back the actual baud rate used,
something which also required 38400 to again be set whenever changing a
SPD flag.
Drop the broken alt-speed handling altogether, and add a ratelimited
warning about using TIOCCSERIAL to change speed as being deprecated.
Note that the rocket driver has never supported using a custom divisor
(ASYNC_SPD_CUST equivalent).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting an alt_speed using the ASYNC_SPD flags has been deprecated since
v2.1.69, and has been broken since v3.10 and commit 6865ff222c ("TTY:
do not warn about setting speed via SPD_*") without anyone noticing.
Drop the broken alt-speed handling altogether, and add a ratelimited
warning about using TIOCCSERIAL to to change speed as being deprecated.
Note that using ASYNC_SPD_CUST is still supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting an alt_speed using the ASYNC_SPD flags has been deprecated since
v2.1.69, and has been broken since v3.10 and commit 6865ff222c ("TTY:
do not warn about setting speed via SPD_*") without anyone noticing.
Drop the broken alt-speed handling altogether, and add a ratelimited
warning about using TIOCCSERIAL to change speed as being deprecated.
Note that using ASYNC_SPD_CUST is still supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Contrary to what a comment claimed, the ASYNC_SPD flags and custom
divisor can be set by a non-privileged user so rate limit the
deprecation notice as was intended.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Select statements in Kconfig do not necessarily enable all required
dependencies and can lead to broken configs. This is also the case
for the "select IUCV" statement within HVC_IUCV:
warning: (HVC_IUCV) selects IUCV which has unmet direct
dependencies (NET && S390)
Just add the missing "depends on NET" to avoid broken configs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We are trying to get rid of DRIVER_ATTR(), and the hvc driver's
attribute can be trivially changed to use DRIVER_ATTR_RW().
Cc: Jiri Slaby <jslaby@suse.com>
Cc: <linuxppc-dev@lists.ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When opening the slave end of a PTY, it is not possible for userspace to
safely ensure that /dev/pts/$num is actually a slave (in cases where the
mount namespace in which devpts was mounted is controlled by an
untrusted process). In addition, there are several unresolvable
race conditions if userspace were to attempt to detect attacks through
stat(2) and other similar methods [in addition it is not clear how
userspace could detect attacks involving FUSE].
Resolve this by providing an interface for userpace to safely open the
"peer" end of a PTY file descriptor by using the dentry cached by
devpts. Since it is not possible to have an open master PTY without
having its slave exposed in /dev/pts this interface is safe. This
interface currently does not provide a way to get the master pty (since
it is not clear whether such an interface is safe or even useful).
Cc: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Valentin Rothberg <vrothberg@suse.com>
Signed-off-by: Aleksa Sarai <asarai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid future diversions between fs/compat_ioctl.c and
drivers/tty/pty.c, define .compat_ioctl callbacks for the relevant
tty_operations structs. Since both pty_unix98_ioctl() and
pty_bsd_ioctl() are compatible between 32-bit and 64-bit userspace no
special translation is required.
Signed-off-by: Aleksa Sarai <asarai@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commtech adapters apparently need the original setting as outputs, see
https://marc.info/?l=linux-gpio&m=149557425201323&w=2. Account for that.
Fixes: 7dea8165f1 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only vgacon and sisusbcon did it right, the rest (via generic code) tried
underline (usually cyan).
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again, a nice linear transfer that simplifies the code.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A nice big linear transfer, no need to flip stac/PAN/etc every half-entry.
Also, yay __put_user() after checking only read.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only read access is checked before this call.
Actually, at the moment this is not an issue, as every in-tree arch does
the same manual checks for VERIFY_READ vs VERIFY_WRITE, relying on the MMU
to tell them apart, but this wasn't the case in the past and may happen
again on some odd arch in the future.
If anyone cares about 3.7 and earlier, this is a security hole (untested)
on real 80386 CPUs.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
CC: stable@vger.kernel.org # v3.7-
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus wants to get rid of these functions, and these uses are especially
egregious: they copy a big linear array element by element.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Cc: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want the tty locking fix in here, so that maybe we can finally get it
fixed for real...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 925bb1ce47.
It causes lots of warnings and problems so for now, let's just revert
it.
Reported-by: <valdis.kletnieks@vt.edu>
Reported-by: Russell King <linux@armlinux.org.uk>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the kernel doc warnings in the driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the hooks for an optional reset controller in the 8250 device
tree node.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_cleanup_mux() is called in the line discipline close path which
is called at tty_release() time. At this stage the tty is no longer
operational enough to send any frames. Sending close frames is
therefore not possible and waiting for their answers always times
out.
This patch removes sending close messages and waiting for their answers
from the tty_release path.
This patch makes explicit what previously implicitly had been the case
already: We are not able to tell the modem that we are about to close
the multiplexer on our side. This means the modem will stay in
multiplexer mode and re-establishing the multiplexer later fails. The
only way for userspace to work around this is to manually send a close
frame in N_TTY mode after closing the mux.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sccnxp driver doesn't get the correct uart clock rate, if CONFIG_HAVE_CLOCK
is disabled. Correct usage of clk API to make it work with/without it.
Fixes: 90efa75f7a (serial: sccnxp: Using CLK API for getting UART clock)
Suggested-by: Russell King - ARM Linux <linux@armlinux.org.uk>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Historically the N_TTY driver could never fail but this has become broken over
time. Rather than trying to rewrite half the ldisc layer to fix the breakage
introduce a second level of fallback with an N_NULL ldisc which cannot fail,
and thus restore the guarantees required by the ldisc layer.
We still try and fail to N_TTY first. It's much more useful to find yourself
back in your old ldisc (first attempt) or in N_TTY (second attempt), and while
I'm not aware of any code out there that makes those assumptions it's good to
drive(r) defensively.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver calls ioremap() in the probe function but doesn't call
iounmap() in the remove function correspondingly. Do so now.
Follow commit 5c9d6abed9 ("serial: altera_jtaguart: adding iounmap()")
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e61c38d85b ("serial: imx: setup DCEDTE early and ensure DCD and
RI irqs to be off") has a flaw: While UCR3 and UFCR were modified using
read-modify-write before it switched to write register values
independent of the previous state. That's a good idea in principle (and
that's why I did it) but needs more care.
This patch reinstates read-modify-write for UFCR and for UCR3 ensures
that RXDMUXSEL and ADNIMP are set for post imx1.
Fixes: e61c38d85b ("serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mika Penttilä <mika.penttila@nextfour.com>
Tested-by: Mika Penttilä <mika.penttila@nextfour.com>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AUX/mini-UART in the BCM2835 family of procesors is a cut-down
8250 clone. In particular it is lacking support for the following
features: CSTOPB PARENB PARODD CMSPAR CS5 CS6
Add a new capability (UART_CAP_MINI) that exposes the restrictions to
the user of the termios API by turning off the unsupported features in
the request.
N.B. It is almost possible to automatically discover the missing
features by reading back the LCR register, but the CSIZE bits don't
cooperate (contrary to the documentation, both bits are significant,
but CS5 and CS6 are mapped to CS7) and the code is much longer.
See: https://github.com/raspberrypi/linux/issues/1561
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit below changed a function call from
dma_request_slave_channel_compat() to dma_request_slave_channel(), but
forgot to update the printed failure message.
Fixes: 219fb0c143 ("serial: sh-sci: Remove the platform data dma slave rx/tx channel IDs")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added meson_uart_enable_tx_engine function is only called
from the console setup, not the runtime uart, which has an open-coded
version of the same register access. This produces a harmless warning
when the console code is disabled:
drivers/tty/serial/meson_uart.c:127:13: error: 'meson_uart_enable_tx_engine' defined but not used [-Werror=unused-function]
Let's move the function inside of the #ifdef to avoid the warning.
Fixes: ba50f1df13 ("serial: meson: remove unneeded variable assignment in meson_serial_port_write")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable serdev support by using the new device-registration helpers.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new interface for registering a serdev controller and clients, and
a helper function to deregister serdev devices (or a tty device) that
were previously registered using the new interface.
Once every driver currently using the tty_port_register_device() helpers
have been vetted and converted to use the new serdev registration
interface (at least for deregistration), we can move serdev registration
to the current helpers and get rid of the serdev-specific functions.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 6fe729c4bd ("serdev: Add serdev_device_write
subroutine") the function serdev_device_write_buf cannot be used in
atomic context anymore (mutex_lock is sleeping). So restore the old
behavior.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 6fe729c4bd ("serdev: Add serdev_device_write subroutine")
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With serdev we might end up with serial ports that have no cdev exported
to userspace, as they are used as the bus interface to other devices. In
that case serial_match_port() won't be able to find a matching tty_dev.
Skip the irq wakeup enabling in that case, as serdev will make sure to
keep the port active, as long as there are devices depending on it.
Fixes: 8ee3fde047 (tty_port: register tty ports with serdev bus)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_insert_flip_string_fixed_flag() is racy against itself when called
from the ioctl(TCXONC, TCION/TCIOFF) path [1] and the flush_to_ldisc()
workqueue path [2].
The problem is that port->buf.tail->used is modified without consistent
locking; the ioctl path takes tty->atomic_write_lock, whereas the workqueue
path takes ldata->output_lock.
We cannot simply take ldata->output_lock, since that is specific to the
N_TTY line discipline.
It might seem natural to try to take port->buf.lock inside
tty_insert_flip_string_fixed_flag() and friends (where port->buf is
actually used/modified), but this creates problems for flush_to_ldisc()
which takes it before grabbing tty->ldisc_sem, o_tty->termios_rwsem,
and ldata->output_lock.
Therefore, the simplest solution for now seems to be to take
tty->atomic_write_lock inside tty_port_default_receive_buf(). This lock
is also used in the write path [3] with a consistent ordering.
[1]: Call Trace:
tty_insert_flip_string_fixed_flag
pty_write
tty_send_xchar // down_read(&o_tty->termios_rwsem)
// mutex_lock(&tty->atomic_write_lock)
n_tty_ioctl_helper
n_tty_ioctl
tty_ioctl // down_read(&tty->ldisc_sem)
do_vfs_ioctl
SyS_ioctl
[2]: Workqueue: events_unbound flush_to_ldisc
Call Trace:
tty_insert_flip_string_fixed_flag
pty_write
tty_put_char
__process_echoes
commit_echoes // mutex_lock(&ldata->output_lock)
n_tty_receive_buf_common
n_tty_receive_buf2
tty_ldisc_receive_buf // down_read(&o_tty->termios_rwsem)
tty_port_default_receive_buf // down_read(&tty->ldisc_sem)
flush_to_ldisc // mutex_lock(&port->buf.lock)
process_one_work
[3]: Call Trace:
tty_insert_flip_string_fixed_flag
pty_write
n_tty_write // mutex_lock(&ldata->output_lock)
// down_read(&tty->termios_rwsem)
do_tty_write (inline) // mutex_lock(&tty->atomic_write_lock)
tty_write // down_read(&tty->ldisc_sem)
__vfs_write
vfs_write
SyS_write
The bug can result in about a dozen different crashes depending on what
exactly gets corrupted when port->buf.tail->used points outside the
buffer.
The patch passes my LOCKDEP/PROVE_LOCKING testing but more testing is
always welcome.
Found using syzkaller.
Cc: <stable@vger.kernel.org>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Straighten out the initcall error handling to avoid deregistering a
never-registered tty driver (something which would lead to a
NULL-pointer dereference) in the most unlikely event that driver
registration fails (e.g. we've run out of major numbers).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to deregister the SPI driver before releasing the tty driver
to avoid use-after-free in the SPI remove callback where the tty
devices are deregistered.
Fixes: 72d4724ea5 ("serial: ifx6x60: Add modem power off function in the platform reboot process")
Cc: stable <stable@vger.kernel.org> # 3.8
Cc: Jun Chen <jun.d.chen@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does ioremap(port->mapbase, ALTERA_JTAGUART_SIZE),
but there is no any iounmap().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After migrating 8250_exar to MSI in 172c33cb61, we can get stuck
without further interrupts because of the special wake-up event these
chips send. They are only cleared by reading INT0. As we fail to do so
during startup and shutdown, we can leave the interrupt line asserted,
which is fatal with edge-triggered MSIs.
Add the required reading of INT0 to startup and shutdown. Also account
for the fact that a pending wake-up interrupt means we have to return 1
from exar_handle_irq. Drop the unneeded reading of INT1..3 along with
this - those never reset anything.
An alternative approach would have been disabling the wake-up interrupt.
Unfortunately, this feature (REGB[17] = 1) is not available on the
XR17D15X.
Fixes: 172c33cb61 ("serial: exar: Enable MSI support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTn_FRAME_PARITY_ODD is 0x0300
UARTn_FRAME_PARITY_EVEN is 0x0200
So if the UART is configured for EVEN parity, it would be reported as ODD.
Fix it by correctly testing if the 2 bits are set.
Fixes: 3afbd89c96 ("serial/efm32: add new driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port client data must be set when registering the serdev controller
or client deregistration will fail (and the serdev devices are left
registered and allocated) if the port was never opened in between.
Make sure to clear the port client data on any probe errors to avoid a
use-after-free when the client is later deregistered unconditionally
(e.g. in a tty-port deregistration helper).
Also move port client operation initialisation to registration. Note
that the client ops must be restored on failed probe.
Fixes: bed35c6dfa ("serdev: add a tty port controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8ee3fde047.
The new serdev bus hooked into the tty layer in
tty_port_register_device() by registering a serdev controller instead of
a tty device whenever a serdev client is present, and by deregistering
the controller in the tty-port destructor. This is broken in several
ways:
Firstly, it leads to a NULL-pointer dereference whenever a tty driver
later deregisters its devices as no corresponding character device will
exist.
Secondly, far from every tty driver uses tty-port refcounting (e.g.
serial core) so the serdev devices might never be deregistered or
deallocated.
Thirdly, deregistering at tty-port destruction is too late as the
underlying device and structures may be long gone by then. A port is not
released before an open tty device is closed, something which a
registered serdev client can prevent from ever happening. A driver
callback while the device is gone typically also leads to crashes.
Many tty drivers even keep their ports around until the driver is
unloaded (e.g. serial core), something which even if a late callback
never happens, leads to leaks if a device is unbound from its driver and
is later rebound.
The right solution here is to add a new tty_port_unregister_device()
helper and to never call tty_device_unregister() whenever the port has
been claimed by serdev, but since this requires modifying just about
every tty driver (and multiple subsystems) it will need to be done
incrementally.
Reverting the offending patch is the first step in fixing the broken
lifetime assumptions. A follow-up patch will add a new pair of
tty-device registration helpers, which a vetted tty driver can use to
support serdev (initially serial core). When every tty driver uses the
serdev helpers (at least for deregistration), we can add serdev
registration to tty_port_register_device() again.
Note that this also fixes another issue with serdev, which currently
allocates and registers a serdev controller for every tty device
registered using tty_port_device_register() only to immediately
deregister and deallocate it when the corresponding OF node or serdev
child node is missing. This should be addressed before enabling serdev
for hot-pluggable buses.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
modified the probing logic for PNP0501 devices, to remove a collision
between the generic 16550A driver and the Fintek driver, which reused
the same ACPI _HID.
The Fintek device probe is now incorporated into the common 8250 probe
path, and gets called for all discovered 16550A compatible devices,
including ones that are MMIO mapped rather than IO mapped. However,
the Fintek driver assumes the port base is a I/O address, and proceeds
to probe some arbitrary offsets above it.
This is generally a wrong thing to do, but on ARM systems (having no
native port I/O), this may result in faulting accesses of completely
unrelated MMIO regions in the PCI I/O space. Given that this is at
serial probe time, this results in hard to diagnose crashes at boot.
So let's restrict the Fintek probe to devices that we know are using
port I/O in the first place.
Fixes: fa01e2ca9f ("serial: 8250: Integrate Fintek into 8250_base")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change interrupt description from driver name to tty name
(e.g. ttyAML0). If multiple serial ports are enabled this
allows to determine which interrupt belongs to which port
in /proc/interrupts.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flag UPF_IOREMAP is used by the 8250 subsystem only, it's not used
by the serial core. Therefore I don't see any benefit in using it
here.
In addition fix the order of calls in meson_uart_release_port.
Unmapping needs to be done first, reversing call order in
meson_uart_request_port.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Member mapsize of struct uart_port is meant to store the resource size.
By using it we can get rid of meson_uart_res_size().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
val is set in both branches of the if clause, therefore the two
removed lines are dead code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to set AML_UART_TX_EN in each call to
meson_serial_port_write. In addition to meson_uart_startup
set this flag in meson_serial_console_setup and
meson_serial_early_console_setup.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stop bit value as to be or'ed, so far this worked only just by chance
because AML_UART_STOP_BIN_1SB is 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in printk message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the safe default for GPIOs with unknown external wiring.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
18a4208 introduced a change to reduce the RX DMA latency on the first reception
when the serial port was opened for reading. However it was claiming a hardirq
unsafe lock after a hardirq safe lock which is not allowed and causes lockdep
to complain verbosely.
This patch changes the code to always start RX DMA earlier, instead of
relying on the flags used to open the serial port removing the code that
was looking for the serial file flags.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of returning the requested baudrate, we better return the
actual one because it isn't always the same.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically
happen during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with overlapping major/minor numbers are
included.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_register_driver call binds the driver to a specific device
node through tty_register_driver call. This should typically
happen during device probe call.
In a multiplatform scenario, it is possible that multiple serial
drivers are part of the kernel. Currently the driver registration fails
if multiple serial drivers with overlapping major/minor numbers are
included.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DMA is enabled and used, a burst of old data may be seen on the
serial console during "poweroff" or "reboot". uart_flush_buffer()
clears the circular buffer, but sci_port.tx_dma_len is not reset.
This leads to a circular buffer overflow, dumping (UART_XMIT_SIZE -
sci_port.tx_dma_len) bytes.
To fix this, add a .flush_buffer() callback that resets
sci_port.tx_dma_len.
Inspired by commit 31ca2c63fd ("tty/serial: atmel: fix race
condition (TX+DMA)").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds a driver for the 16550-based Aspeed virtual UART
device. We use a similar process to the of_serial driver for device
probe, but expose some VUART-specific functions through sysfs too.
The VUART is two UART 'front ends' connected by their FIFO (no actual
serial line in between). One is on the BMC side (management controller)
and one is on the host CPU side.
This driver is for the BMC side. The sysfs files allow the BMC
userspace, which owns the system configuration policy, to specify at
what IO port and interrupt number the host side will appear to the host
on the Host <-> BMC LPC bus. It could be different on a different system
(though most of them use 3f8/4).
OpenPOWER host firmware doesn't like it when the host-side of the
VUART's FIFO is not drained. This driver only disables host TX discard
mode when the port is in use. We set the VUART enabled bit when we bind
to the device, and clear it on unbind.
We don't want to do this on open/release, as the host may be using this
bit to configure serial output modes, which is independent of whether
the devices has been opened by BMC userspace.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probing of THRE irq behaviour assumes the other end will be reading
bytes out of the buffer in order to probe the port at driver init. In
some cases the other end cannot be relied upon to read these bytes, so
provide a flag for them to skip this step.
Bit 19 was chosen as the flags are a int and the top bits are taken.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UPF_EXAR_EFR is set globally for each port enumerated by the driver.
Thus, no need to repeat this in individual ->setup() hook.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.
But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.
It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds spk_ttyio.c file. It contains a set of functions which implement
those methods in spk_synth struct which relate to sending bytes out using
serial comms. Implementations in this file perform the same function but
using TTY subsystem instead. Currently synths access serial ports, directly
poking standard ISA ports by trying to steal them from serial driver. Some ISA
cards actually need this way of doing it, but most other synthesizers don't,
and can actually work by using the proper TTY subsystem through a new N_SPEAKUP
line discipline. So this adds the methods for drivers to switch to accessing
serial ports through the TTY subsystem, whenever appropriate.
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This exports tty_open_by_driver so that it can be called from other
places inside the kernel. The checks for null file pointer are based on
Alan Cox's patch here:
http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1215095.html.
Description below is quoted from it:
"[RFC] tty_port: allow a port to be opened with a tty that has no file handle
Let us create tty objects entirely in kernel space. Untested proposal to
show why all the ideas around rewriting half the uart stack are not needed.
With this a kernel created non file backed tty object could be used to handle
data, and set terminal modes. Not all ldiscs can cope with this as N_TTY in
particular has to work back to the fs/tty layer.
The tty_port code is however otherwise clean of file handles as far as I can
tell as is the low level tty port write path used by the ldisc, the
configuration low level interfaces and most of the ldiscs.
Currently you don't have any exposure to see tty hangups because those are
built around the file layer. However a) it's a fixed port so you probably
don't care about that b) if you do we can add a callback and c) you almost
certainly don't want the userspace tear down/rebuild behaviour anyway.
This should however be sufficient if we wanted for example to enumerate all
the bluetooth bound fixed ports via ACPI and make them directly available.
It doesn't deal with the case of a user opening a port that's also kernel
opened and that would need some locking out (so it returned EBUSY if bound
to a kernel device of some kind). That needs resolving along with how you
"up" or "down" your new bluetooth device, or enumerate it while providing
the existing tty API to avoid regressions (and to debug)."
The exported funtion is used later in this patch set to gain access to tty_struct.
[changed export symbol level - gkh]
Signed-off-by: Okash Khawaja <okash.khawaja@gmail.com>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Here is the "big" TTY/Serial patch updates for 4.12-rc1
Not a lot of new things here, the normal number of serial driver updates
and additions, tiny bugs fixed, and some core files split up to make
future changes a bit easier for Nicolas's "tiny-tty" work.
All of these have been in linux-next for a while. There will be a merge
conflict with include/linux/serdev.h coming from the bluetooth tree
merge, which we knew about, as we wanted some of the serdev changes to
go in through that tree. I'll send the expected merge result as a
follow-on message.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWRA9rw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn8OwCXSoCtZMGl25ohu1osCL5G0UEMtgCg2Z9k7hDk
LpQTTN98hHn/VwM47ro=
=X8sk
-----END PGP SIGNATURE-----
Merge tag 'tty-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" TTY/Serial patch updates for 4.12-rc1
Not a lot of new things here, the normal number of serial driver
updates and additions, tiny bugs fixed, and some core files split up
to make future changes a bit easier for Nicolas's "tiny-tty" work.
All of these have been in linux-next for a while"
* tag 'tty-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (62 commits)
serial: small Makefile reordering
tty: split job control support into a file of its own
tty: move baudrate handling code to a file of its own
console: move console_init() out of tty_io.c
serial: 8250_early: Add earlycon support for Palmchip UART
tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44
vt: make mouse selection of non-ASCII consistent
vt: set mouse selection word-chars to gpm's default
imx-serial: Reduce RX DMA startup latency when opening for reading
serial: omap: suspend device on probe errors
serial: omap: fix runtime-pm handling on unbind
tty: serial: omap: add UPF_BOOT_AUTOCONF flag for DT init
serial: samsung: Remove useless spinlock
serial: samsung: Add missing checks for dma_map_single failure
serial: samsung: Use right device for DMA-mapping calls
serial: imx: setup DCEDTE early and ensure DCD and RI irqs to be off
tty: fix comment typo s/repsonsible/responsible/
tty: amba-pl011: Fix spurious TX interrupts
serial: xuartps: Enable clocks in the pm disable case also
serial: core: Re-use struct uart_port {name} field
...
While examining output from trial builds with -Wformat-security enabled,
many strings were found that should be defined as "const", or as a char
array instead of char pointer. This makes some static analysis easier,
by producing fewer false positives.
As these are all trivial changes, it seemed best to put them all in a
single patch rather than chopping them up per maintainer.
Link: http://lkml.kernel.org/r/20170405214711.GA5711@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jes Sorensen <jes@trained-monkey.org> [runner.c]
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kejian Yan <yankejian@huawei.com>
Cc: Daode Huang <huangdaode@hisilicon.com>
Cc: Qianqian Xie <xieqianqian@huawei.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Christian Gromm <christian.gromm@microchip.com>
Cc: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Cc: Jason Litzinger <jlitzingerdev@gmail.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix sparse warnings in drivers/of/.
- Add more overlay unittests.
- Update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names.
- Add a common DT modalias function.
- Move trivial-devices.txt up and out of i2c dir.
- ARM NVIC interrupt controller binding.
- Vendor prefixes for Sensirion, Dioo, Nordic, ROHM.
- Correct some binding file locations.
-----BEGIN PGP SIGNATURE-----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=ca1M
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- fix sparse warnings in drivers/of/
- add more overlay unittests
- update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names
- add a common DT modalias function
- move trivial-devices.txt up and out of i2c dir
- ARM NVIC interrupt controller binding
- vendor prefixes for Sensirion, Dioo, Nordic, ROHM
- correct some binding file locations
* tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (24 commits)
of: fix sparse warnings in fdt, irq, reserved mem, and resolver code
of: fix sparse warning in of_pci_range_parser_one
of: fix sparse warnings in of_find_next_cache_node
of/unittest: Missing unlocks on error
of: fix uninitialized variable warning for overlay test
of: fix unittest build without CONFIG_OF_OVERLAY
of: Add unit tests for applying overlays
of: per-file dtc compiler flags
fpga: region: add missing DT documentation for config complete timeout
of: Add vendor prefix for ROHM Semiconductor
of: fix "/cpus" reference leak in of_numa_parse_cpu_nodes()
of: Add vendor prefix for Nordic Semiconductor
dt-bindings: arm,nvic: Binding for ARM NVIC interrupt controller on Cortex-M
dtc: update warning settings for new bus and node/property name checks
scripts/dtc: Update to upstream version v1.4.4-8-g756ffc4f52f6
scripts/dtc: automate getting dtc version and log in update script
of: Add function for generating a DT modalias with a newline
of: fix of_device_get_modalias returned length when truncating buffers
Documentation: devicetree: move trivial-devices out of I2C realm
dt-bindings: add vendor prefix for Dioo
..
Tetsuo has reported that sysrq triggered OOM killer will print a
misleading information when no tasks are selected:
sysrq: SysRq : Manual OOM execution
Out of memory: Kill process 4468 ((agetty)) score 0 or sacrifice child
Killed process 4468 ((agetty)) total-vm:43704kB, anon-rss:1760kB, file-rss:0kB, shmem-rss:0kB
sysrq: SysRq : Manual OOM execution
Out of memory: Kill process 4469 (systemd-cgroups) score 0 or sacrifice child
Killed process 4469 (systemd-cgroups) total-vm:10704kB, anon-rss:120kB, file-rss:0kB, shmem-rss:0kB
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
sysrq: SysRq : Manual OOM execution
sysrq: OOM request ignored because killer is disabled
The real reason is that there are no eligible tasks for the OOM killer
to select but since commit 7c5f64f844 ("mm: oom: deduplicate victim
selection code for memcg and global oom") the semantic of out_of_memory
has changed without updating moom_callback.
This patch updates moom_callback to tell that no task was eligible which
is the case for both oom killer disabled and no eligible tasks. In
order to help distinguish first case from the second add printk to both
oom_killer_{enable,disable}. This information is useful on its own
because it might help debugging potential memory allocation failures.
Fixes: 7c5f64f844 ("mm: oom: deduplicate victim selection code for memcg and global oom")
Link: http://lkml.kernel.org/r/20170404134705.6361-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/tty/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jiri Slaby <jslaby@suse.com>
cc: linux-serial@vger.kernel.org
Move 21285 entry down alongside other UART drivers to be more consistent
with the rest of the file. It is kept before 8250 though, to preserve the
existing link ordering between those two.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it easier for job control to become optional and/or usable
independently from tty_io.c, as well as providing a nice purpose
separation. No logical changes from this patch.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow reuse without the rest of the tty_ioctl code.
No logical changes from this patch.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Antonio Borneo